CDA HVN61/81 User's Manual
Contents
1. A series of small iD or F7 is displayed After turning on a zone the indicator lights on the control panel continue to flash The saucepans make noise during cooking or your hob makes a clicking sound during cooking The fan continues to function for a few minutes after the hob is turned off IMPORTANT PLEASE NOTE In the event of any breakage crack or cracking even minima ately disconnect your appliance to prevent a risk of electric shock and contact CDA Custome There was an overflow or an object is in contact with the control panel The electronic boards heated up The cookware used is not suitable for induction or is less than 12 cm in diameter 10 cm on the 16 cm zone This is normal with some types of cookware This is caused by the transfer of energy from the hob to the cookware Cooling of the electronic components Working normally Clean the hob or remove the object and begin cooking again See the Installation section See the section on cookware for induction Rome There is no risk neither to your ob nor to your cookware Nothing F Fitting the Hob Unpacking the hob Take care not to lose or mishandle any parts Fitting position of the hob This appliance must be installed a minimum of 50mm from any back wall and a minimum of 1 cent vertical surfaces e g a tall cupboard end panel This may be reduced to 100mm if the adja2. HVN61 81 Induction Hob Manual for Installation Use and Maintenance C D A Customer Care Department The CIDIAlGroup Ltd Harby Road Langar Nottinghamshire e NG13 9HY T 01949 862 012 F 01949 862 003 E service cda eu W www cda eu Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorr product Please note that CDA reserve the right to invalidate the guarantee supplied with th installation or misuse of the appliance or use in a commercial environment This appliance is not designed to be used by people including children with reduced capacity or who lack experience or knowledge about it unless they have had supervision the appliance by someone who is responsible for their safety Under no circumstances should any external covers be removed for servicing or maintenan personnel Appliance information Please enter the details on the appliance rating plate below for reference to assist CDA Cu fault with your appliance and to register your appliance for guarantee purposes CE Declarations of Conformity This appliance has been manufactured to the strictest standards and complies with all ap Electrical safety LVD 2006 95 EC and Electromagnetic interference compatibility intended to come into contact with food conform to 89 109 EC IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN DIRECTIVE 2002 96 EC At the end of its working life the product must be tak
3. To change the timer once set Touch the Oor keys until the timer display shows the required duration To cancel the timer once set Touch the Dor keys simultaneously or reduce the time required using the O key unti display shows 0 Please note If you cancel the timer the zone will continue at the set power level until it is switched off as d Tempo function The hob is equipped with a Tempo function which allows you to see how long the zone has be set the timer for the remaining time you need it to cook perfect if you are interrupted when To see how long the zone has been on since the power level was set Touch the key at any time during cooking The timer display will flash the number of minu current power level for five seconds To set the remaining cooking time Touch the key at any time during cooking Whilst the timer display is flashing touch the time required The timer display will show the required time for three seconds and beep to co the remaining cooking time is displayed Please note Once the cooking time is set you cannot change it for five seconds after touching t display has stopped flashing the cooking time can be changed The Tempo function shows the total time elapsed since the last power level was set level the time elapsed is reset Safety Features The childlock The hob is equipped with a childlock to lock the controls This can be used when the hob is off To set the childloc
4. alternate between the power level set and PC e To cancel the precook and return to normal cooking set the power level required using th Please note Using the boost or precook function on one zone automatically limits the power level availabl side If you wish to use several pans at the same time try to use zones on opposite sides Please note e When the zone display shows PC the zone will switch off automatically after five seconds e The precook time is preset according to the power level selected e The precook function can only be used for cooking at power levels 6 12 e If you have set the direct power key to a power level below six touching that key when se set the power level at 6 The timer The timer allows you to preset the length of time any of the zones will be on between a maximum of ninety nine minutes The timer can be used on each zone separately To set the timer e First switch on the zone and set the power level Touch either the OD or keys until the timer display shows the required duration e To go straight to the maximum 99 minutes touch the a key once when the timer is swit Please note e The timer will only count down when the cookware is on the zone e The timer will count down in minutes and then in seconds for the last minute e Atthe end of the set time the zone will switch off the timer will flash O and the hob will b seconds To switch off the alert touch any key for that zone
5. by a qualified electrician who is a member a will comply with the 1 E E and local regulations This appliance is intended to be connected to fixed wiring and is not suitable for conne 13a supply This appliance is intended to be connected to fixed wiring by a double pole switch having a a least 3mm in all poles The switch must be positioned no further than 2m from the appliance This appliance is supplied with a 3 core mains cable the wires are in accordance with the folla Green amp Yellow Earth Blue Neutral Brown Live Please note e The mains cable must only be replaced by a qualified service engineer and must be of eq better rating i e 2 5mm HO5V2V2 F e This appliance is intended to be connected to the mains supply with a cable of cross secti cable will not fit the terminal connections e The marking of the current rating of the fuse or circuit breaker protecting this appliance should b socket outlet e Assembly and electrical connection should be carried out by specialised personnel When installing this product we recommend you seek the help of another individual Black grey Green yellow Green yellow N L O N L O Use a 32A circuit breaker or fuse Fig 7 CDA To contact our Customer Care Department or for Service please contact us on the details below
6. the power off Touch the key for the zone used or reduce the power level on the zone by touching the display switches off Direct power keys e The hob is equipped with two keys to allow access to a specific power level for ease of use e After turning the power on for the zone required touch either of the direct power keys as other power level touch either Oor keys until the required power level is shown ont Low heat Power level 6 CIN High heat Power level 10 e Itis possible to adjust the direct power keys if necessary To do so when the hob is switch key for approximately five seconds until the hob beeps and the display shows the current or Y keys until the zone display shows the required power level The hob will beep aft to confirm the new power level has been set Boost The hob is equipped with a boost function once the zone is switched on allowing a higher for an unspecified length of time To turn on the boost function touch the Y key bo wil the pan has reached the temperature required then select the required power level by tou V or Please note e The boost function does not switch off automatically You must set a power level when b Precook preheat function for power levels 6 12 Touch and hold the key until the zone display shows 12 and then touch the amp key agai for five seconds during which you must set the power level required as described above selection and the zone display will
7. DA Customer Care A Customer Care Department The CDA Group Ltd Harby Road Langar Nottinghamshir T 01949 862 012 F 01949 862 003 E service cda eu W www cda eu Troubleshooting On first use Possible Causes What should you do The display shows a series of digits and l Working normally symbols on first connection The electrical connection of the hob is incorrect Installation blows a fuse or only one side of the hob works Nothing the hob will be ready to use within approximately 30 seconds Check that it is set up properly see the Electrical Connection section The hob produces an odour during the N Heat a saucepan full of water on each ew appliance first cooking sessions cooking zone for 30 minutes On switching on Possible Causes What should you do The hob does not work and the lights on the control panel do not switch on The hob is not oe and the display shows a non standard graphic The hob is not working and the display shows 2 1 The hob is not connected to the power supply or the power supply is faulty The electronics are not functioning correctly The childlock is on Check the electrical circuit breaker and fuses Call CDA Customer Care Switch off the childlock before trying to use the hob Possible Causes What should you do The hob has stopped operating The hob beeps at approximately ten second intervals and a em or F7 is displayed on the zone display
8. en to a special local authority waste c providing appliance recycling services Disposing of a household appliance separately avoids possible negative consequences for the enables the constituent materials to be recovered saving both energy and resources As a remi household appliances separately the product is marked with a crossed out wheeled dustbin A Please note e Induction hobs become hot and remain hot during and immediately after use Do nott been allowed to cool e Keep children away from the appliance when in use e Never use the hob top for storage e Pan handles should never stand out beyond the edge of the worktop This will ensure Do not lean over the hob when it is in use e Follow the cleaning instructions carefully e Ensure the base of the saucepan is clean and dry before placing it on the hob e Avoid hard shocks from cookware the vitroceramic glass surface is highly resistant bu e Donot place hot lids flat on the hob top A suction effect could cause damage to the e Do not drag cookware across the hob top in the long term this could cause damage to e Do not store cleaning or flammable products in the unit below the hob e Always use appropriate cookware Do not cook unopened tins of food directly on the hob e Never put cooking foil or plastic materials on the ceramic surface when the hob is hot and cause damage to the hob e This hob Class 3 has been designed for use only as a cooking ap
9. k Touch the Y key for approximately three seconds until the LED above the childlock key illumi confirm the childlock is switched on To turn off the childlock Touch the key for approximately three seconds until the LED above the childlock key goes to confirm the childlock is switched off Use of the childlock when the hob is off The childlock LED will illuminate briefly when any zone control key is touched Use of the childlock when the hob is in use The zone control display will alternate between showing the selected power level and the A 1 in use For any zone not in use the display will show the 7 locked symbol the hob will beep and th briefly when the control keys are touched It is possible to switch off a zone when the childlock is on for safety reasons Residual Heat Indicators The hob is equipped with residual heat indicators to warn when any of the zones are still hot t An H will flash in the relevant zone display after cooking until the zone is at a safe temperature Please note You should avoid touching the zones when the hob is in use or when an H is showing on the z In the event of a power cut the residual heat indicators will illuminate after the power supply i there is no power supply to the hob the residual heat indicators will not work so extra care m Temperature Limiter The hob is equipped with a temperature limiting sensor that adjusts the power output of the cookware becomes too hot preventing damage to the co
10. okware and to the hob itself Small Object Safety The hob will not operate if a small object is left on the hob top for example a fork The zone c warn there is something too small on the hob Please note Several small objects left together may be detected by the hob as a piece of cookware In this c the objects may heat up Overflow Protection The hob is equipped with a sensor that will switch off the hob and display the WD symbol the following situations e Overflow from the pan spills over the control keys A damp cloth is placed over the control keys e A metallic object is placed over the control keys Auto stop Protection The hob is equipped with a sensor that will switch off the hob after a factory set period of tim on the power level set The hob will show AS or A in the zone display and beep for approxim off the alert touch any key Efficient Use of your Hob The hob is equipped with zones of different sizes designed to accommodate most shap results only use pans with flat bottoms and choose an appropriate zone depending on the ficient use of the hob is shown below where the pan and zone are correctly chosen Use pan lids where possible to minimize the energy usage of your appliance It is very important that the pans used on the hob are made of a suitable material and have base of the pan must be clean before use to prevent any scratches on the hob top Care and Maintenance Always disconnect the ap
11. pliance Any other use incorrect and therefore dangerous FOR THOSE WITH HEART PACEMAKERS OR ACTIVE IMPLANTS The function of this hob conforms to current electromagnetic interference standards and t with legal requirements 2004 108 CE directives To avoid interference between your hob and a pacemaker your pacemaker must be design compliance with the regulations that apply to it As such CDA guarantee only that our pro With regard to the compliance of the pacemaker or any potential incompatibility you sho the manufacturer or your attending physician Important Do not use the hob if the glass surface is cracked or damaged to prevent the risk of ele from the power supply e Ensure that the power cable of a connected electrical appliance near the hob is not in c cooking zones Cooking on Induction The principle of induction cooking is based on magnetic effect When you put your cookware on an induction zone and switch it on the electronic boards currents in the base of the cookware and instantly raise its temperature This heat is then t the cookware The best cookware to use with induction cooking has thick flat bases as the heat will be be more evenly Most cookware is compatible with induction cooking There are three ways to check the s 1 Using a magnet to see if the base of the pan is magnetic if three magnet sticks then t 2 Place the pan on one of the cooking zones switched on to power level 4 if the display r cook
12. pliance from the power supply before undertaking any cleaning o Important e Steam cleaners must not be used when cleaning this appliance You should use a non abrasive cleaner to clean the hob top Any abrasive cleaner including Q could erase the control panel markings Sugar and starch can cause permanent damage to the surface of the hob Wipe away any spill Wipe over the zone to be cleaned with a N and hot ganing O water and then wipe off with a soft dry cloth Wipe over the zone to be cleaned with a sponge and hot water using a ceramic scraper to remove any large marks or stains and then wipe off with a soft dry cloth Accumulated baked on stains Cleaning sponge or glass scraper dirt sugar spills or melted plastics and soft cloth Pour a small amount of warm white vinegar onto the stain leave it to stand and then wipe off with a soft dry cloth Rings and hard water residues White vinegar and soft cloth Cleaning agent for vitroceramic Shiny metallic streaks glass etc Slow boiling e g spa ghetti soups stews potatoes Use specialist vitroceramic glass cleaner preferably one with silicone for its protective properties If your hob is not working 1 Check that the zone is switched on 2 Check that the mains supply has not been switched off 3 Check that the fuse in the spur has not blown In the event of a fault with the hob please advise CDA Customer Care of any fault code sh Contact C
13. that you increase the ventilation of the hob by creating an opening in the side a e Ensure that the top rail is removed prior to installation and that no unit cross member is bla e If the hob is to be located above a working drawer we recommend that the drawer is not us example dusters or towels this is to minimize the risk of the cooling system air intakes being O Air intake Air outlet B O Vitroceramic glass Power cord 2 le a How to install the hob Overall dimensions of the hob HVN61FR Width 580 mm Depth 510 mm HVN81FR Width 770 Worktop cut out dimensions HVN61FR Width 560 mm Depth 490 mm HVN81FR Width 750 1 Make the required hole in the worktop Before doing this you must check the instructic hood to ensure that you will have the required clearance The cut out Fig 6 shows a 6 the cut out edge The distance from the hob when fitted to the back wall is 50mm If a splashback worktop upstand is to be fitted take this into account when cutting the that the hob should be positioned away from the rear wall or splashback is 50mm 2 Fix the foam seal underneath the appliance by following the outline of the worktop upa This ensures an airtight seal with the worktop Do not use silicone type sealant Above an oven y Mains Electricity Connection Warning this appliance must be earthed We recommend that the appliance is connected
14. tiles or steel for example These dimensions are shown in Fig 6 Ventilation requirements This appliance must be installed to allow air to flow freely to the air intake A in figure 3 and fi 3 Failure to allow sufficient ventilation could cause damage to the hob and constitutes incorre covered by the warranty If fitting a cooker hood above the hob If a cooker hood is to be installed above the hob the height of the hood above the hob must b recommended Fig 5 If the instructions supplied with the hood dictate that the hood must b than 600mm then that height is the minimum required Wall furniture requirements The minimum height of any cabinet immediately above the hob is 900mm The minimum heig including light pelmets is 400mm unless they are manufactured from a material resistant to Notes e Do not position this appliance above a refrigeration unit The heat generated may cause th e This appliance is designed to be installed into cabinet units capable of withstanding tempe above ambient temperature e Never place perishable foods cleaning products or flammable items in the cupboard belo e Ifan oven is to be installed below the hob the thermal safety system on the hob will not al same time as a pyrolytic programme on the oven e The hob is equipped with an anti overheating safety device that can be activated if the hob that is not sufficiently ventilated In the event that this occurs the control panel will show recommend
15. ware is compatible If the display flashes the cookware cannot be used on an indu 3 Check the instructions or packaging of the pans for the symbols indicating suitability fo Using your Hob HVN61FR Zones HVN81FR Zones 1 Front left 2 8 kW 180 mm 5 Front left 2 2 kW 160 2 Back left 2 8 kW 180 mm 6 Back left 31 kW 210 m 3 Back right 31 kW 210 mm 7 Back right 2 2 kW 160 4 Front right 2 2 kW 160 mm 8 Frontright31 kW 210 ontrol panel 9 Power key 10 Power level keys 11 Direct power key 12 Zone indicator Y 13 Boost 9 14 Direct power key 2 15 Tempo function 16 Timer keys Childlock 17 The table below offers guidance as to what each power level is for For melting butter chocolate or keeping food warm 3 4 Keeping food hot or to heat small quantities of liquid 5 6 Heat larger quantities of liquid sauces etc 7 8 Slow boiling e g spaghetti soups stews potatoes 9 10 Gentle frying Browning meats frying fish omelettes Using your Hob To switch the zone on Touch the key for the zone required The zone display will flash 0 and the hob will bee Please note If a power level is not set within five seconds the zone will switch off automatic To set the power level Touch the key to increase the power level from 1 lowest to 12 maximum and the e To go straight to 12 touch the key when the zone is switched on To turn
Download Pdf Manuals
Related Search