Casio Watch MA1106-EA User's Manual
Contents
1. To set the day 3 dials timekeeping seconds stopwatch minutes and 1 20 seconds day 1 Pull the crown out to the first click Stopwatch function Measuring capacity 59 59 95 2 Set the day by rotating the crown a Measuring unit 1 20 second 3 Push the crown back in to the normal position Measuring mode Elapsed time e Avoid changing the date setting while the current time is between 9 00 p m and F i Battery One silver oxide battery Type SR927W a Approximately 3 years on type SR927W assuming one stopwatch operation 60 min day Using the Stopwatch Stopwatch 1 20 second hand This hand rotates and Stopwatch minute hand indicates the second count fekt A during the first 30 seconds Ne Stopwatch second hand The stopwatch lets you measure elapsed time up to 59 minutes 59 95 seconds To measure elapsed time First 30 seconds 1 Press to start the stopwatch 2 Press A to stop the stopwatch e You can resume the measurement operation by pressing again 3 Check the elapsed time e The example below shows an elapsed time of 24 65 seconds Stopwatch 1 20 second hand 65 Stopwatch second hand 24 seconds e Press to reset the stopwatch This will enter the Timekeeping Mode To measure elapsed time After the first 30 seconds Press to start the stopwatch e During elapsed time measurement the stopwatch 1 20 second hand automatically rotates for the final second of each minute Press to stop th2. 2 o clock e Holding down will move the second hand at high speed until you release the button Press 8 to move the stopwatch 1 20 second hand to 12 o clock e Holding down will move the 1 20 second hand at high speed until you release the button 5 After making the adjustments you want push the crown back in to its normal position The stopwatch minute hand will move automatically to 12 o clock e Note that pulling the crown out also stops the timekeeping second hand After performing the above procedure you should also adjust the timekeeping setting
3. MA1106 EA Operation Guide 5244 CASIO e Your watch may differ somewhat from the one shown in the illustration E For a watch with an elapsed time bezel Rotate the elapsed time bezel to align the 7 mark with the i minute hand Hour hand To set the time After certain amount of time elapsed read the graduation on 1 When the second hand is at the elapsed time bezel which the minute hand points to Minute hand 12 o clock pull out the crown The elapsed time is indicated to the second click to stop it Set the hands by rotating the First click crown Rotate the crown to e Some water resistant models are equipped with a screw Setting Day move the hands clockwise lock crown Move the minute hand four or e With such models you must unscrew the crown in the gt p five minutes past the time you direction noted in the illustration to loosen it before you can want to set and then back it pull it out Do not pull too forcibly on such crowns Second click up to the proper setting e Also note that such watches are not water resistant while Setting Time Push the crown back in to their crowns are loosened Be sure to screw the crowns the normal position to restart timekeeping back in as far as they will go after making any setting Crown Normal position Day Specifications Second hand Accuracy at normal temperature 20 seconds a month Display 3 analog hands timekeeping hour and minutes stopwatch seconds
4. e stopwatch e You can resume the measurement operation by pressing again Press and the stopwatch 1 20 second hand will move to the 1 20 second count e If the elapsed time operation was stopped during the final second of each minute the stopwatch 1 20 second hand will already be pointing at the 1 20 second count Do not press at this time because doing so will restart the elapsed time operation 4 Check the elapsed time e The example below shows an elapsed time of two minutes 24 65 seconds Stopwatch 1 20 second hand L65 Stopwatch minute hand 2 minutes Stopwatch second hand 24 seconds e Press to reset the stopwatch This will enter the Timekeeping Mode Notes e Do not try to perform stopwatch operations while the crown is pulled out either to the first or second click If you try to press a button you might accidentally cause the crown to rotate and change the current time or day setting e If the starting positions of the stopwatch second hand and 1 20 second hand become misaligned use the following procedures to adjust the positions of the hands so they point to 12 o clock when the stopwatch is reset To adjust the positions of the stopwatch hands Press 8 to reset the stopwatch and check the stopwatch second hand 1 20 second hand and minute hand They all should be at 12 o clock To adjust the hands pull out the crown to the second click Press to move the stopwatch second hand to 1
Download Pdf Manuals
Related Search