Beckett CG25 User's Manual
Contents
1. free the internal gas tube C 2 Gently rock the internal gas tube C to loosen the Burner Model tube from the burner housing D Restrictor Restrictor Part Number Inside Diameter 401 CG10 1 3246700U 3 Inspect the O rings and insure that they are prop ee eee erly lubricated A silicon O ring lubricant is recom CG10 2 3246 701U 042 mended but automotive chassis or bearing grease CG10 3 CG10 25 is an acceptable substitute CG10 1S 3246703U 4 Referring to Figure 2 place the restrictor F with CG10 35 CG10 65 pre attached pre lubricated O ring G into the CG10 4S internal gas tube C Use your hand to press the CG10 5S 3245707U restrictor into the tube The O ring will hold the restrictor in place So CG15 2S 32 5 Insure that the O ring H attached to the outside diameter of internal gas tube is properly lubricated eer and seated against the flange on the internal gas CG16 45 tube CG25 1S 32467 6 Install the internal gas tube C back into the hous CG25 25 ing refer to Figure 1 Fit the end of the tube into CG25 3S the external gas manifold E CG25 4S 3246716U 7 Re install the jacking screw B Refer to the CG25 5S above notice for installation details CG50 1S 8 Fill out and place the supplied Conversion Data CG50 2S 3246719U Plate adjacent to the rating plate CG50 3S 9 Complete and attach the supplied Adjustment Data CG50 4S 3246721U s r CG50 5S With the gas restrictor installed as shown in F2. Propane Restrictor Geckett COMMERCIAL PRODUCTS Conversion Kt Product Description The Beckett Propane Restrictor Conversion Kit allows for the conversion of CG10 CG15 CG25 and CG50 burners for use with propane gas With the proper installation of the restrictor and attached O ring adjustments and settings for propane use will be the same as the adjustments and settings for natural gas use as detailed in the burner manual This conversion kit shall be AWARNING installed by a qualified service agency in accordance with the manufactur er s instructions and all applicable codes and requirements of the authority having jurisdiction In Canada in accordance with the requirements of the CAN CGA B149 Installation Code If the information in these instructions is not followed exactly a fire explosion or production of carbon monoxide may result causing property damage personal injury or loss of life The qualified service agency is responsible for the proper instal lation of this kit The installation is not proper and complete until the operation of the converted appli ance is checked as specified in the manufacturer s instructions supplied with the kit Please carefully read and comply with the instruction manual supplied with the specific burner being convert ed Figure 1 Components Installation Note that Steps 1 and 2 on the reverse side refer to fully assembled burners Skip to Step 3 when convert
3. igures 1 amp 2 all burner air adjustments and gas manifold pressure adjustments for propane will be approximately the same as the natural gas adjustments shown in the burner manual or printed on the Mfr s Settings label on the burner housing For a copy of the current burner manual go to http www beckettcorp com protect tech asp If furtherTechnical assistance is required call 800 645 2876 Monday thru Friday 8AM to 5PM EST Printed in USA R W Beckett Corporation P O Box 1289 Elyria OH 44036 Canada R W Beckett Canada Ltd Unit 3 430 Laird Road Guelph Ontario N1G 3X7 2 Form No 61708 R01 08 08
4. ing a burner without the air tube assembly installed Refer to Figures 1 and 2 when performing the following steps CG15 is shown in the illustrations NOTICE CG25 and CG50 are similar CG10 is similar with the exception of having the gas gun assem bly mounted into the air tube instead of the housing Figure 2 Assembly Location Illustrations Ho Coe o ooms Illustrations Te enna cas aio Propane Rericor Te Rericoro ing Cu Gee bern ob Burner Housing NOTICE Use authorized replacement parts only Restrictors are precision ma Figure 3 Gas Gun Installation chined parts and O rings are rated for fuel contact Do not attempt to replicate or modify any parts Refer to JACKING SCREW Table 1 TIGHTEN SECURELY lt _ The gun assembly is secured inside fol lt lt l E CLIP SHOULD BE FLUSH NOTICE J y i B i WITHSCREWTORMI the air tube by a spring loaded jacking screw It is spring loaded in order to control the force it can impose on the gun assembly When installing the jacking screw look inside the air tube to verify that the pointed tip of the jacking screw pin is seated into the small slot on the locating pad on top of the gun There is also an external verification of correct assembly when the screw is fully tightened the e clip on the top of the center pin should come flush with the top of the screw Refer to Figure 3 1 Remove the jacking screw B from the housing to
Download Pdf Manuals
Related Search