Audiovox SS91 User's Manual
Contents
1. 8 Mail this form along with your payment to Credit card purchasers can order additional or replacement Aa transmitters by phone Simply dial 1 800 645 4994 and follow the instructions from the operator interface Audiovox Electronics Corp 150 Marcus Blvd Hauppauge N Y 11788 Attn TRANSMITTER DEPARTMENT 128 8840 7of8 2010 Audiovox Electronics Corp 150 Marcus Blvd Hauppauge NY 11788 128 8840 128 8840 8 of 82. AUTO SECURITY Model SS91 Transmitter Programming Guide These transmitters makes use of icons symbols to identify the reac tion your security system keyless entry and or remote start system where applicable will have when any icon button is pressed These icons are programmed at time of installation to meet the needs of the individual and to complement the vehicle that the system is installed in To replace a transmitter or add transmitters please follow the programming instructions listed on the pages of this manual RECEIVER BUTTON CHANNEL SYSTEM FUNCTION Lock And Arm Alarm also initiate and terminates Panic Unlock And Disarm also initiates and terminates Panic Programmable to unlock drivers door and or all doors Lock and arm unlock and disarm May be programmed to unlock driver s door or all doors Also will initiate and terminate Panic Pulsed or switched output to control Remote Trunk Release or optional device connected to channel 3 When pressed and release two times will provide pulsed output or activate the Remote Start option when installed When so equipped this button can be used to operate an optional device connected to channel 4 When so equipped this button can be used to operate an optional device connected to channel 5 Where So Equipped 128 8840 1 of 8 Although the most common use of the transmitter buttons are shown on the front page of this g
3. a code has been stored there will be two options 1 Enter the transmitter program mode of the receiver channel to be reprogrammed Using any unused button or combination of but tons push out the stored code by pressing the unused button until a long chirp is heard then repeat 3 additional times After this you 128 8840 4of8 can add any desired unused transmitter button This action erases only the button stored of the transmitter you are programming All other codes will remain stored Enter the transmitter program mode Using any transmitter button press and hold until a long chirp is heard If a single chirp or multiple chirps up to 7 chirps are heard the unit is indicating that the transmitter has already been programmed elsewhere in the re ceiver Release the transmitter button and within 5 seconds press and hold until a long chirp is heard This action forces the unit to erase all stored codes of that transmitter The unit then exits the program mode the siren emits the program mode exit chirp pattern All transmitter buttons for that transmitter must now be reprogrammed Any other transmitter stored in the unit s memory still remain operational If the button is released and not pressed again within the 5 second period no change in programming has been made to the receiver channel The programmer can move onto a different channel or erase the transmitter codes as described in 1 above BATTERY REPLACEMENT T
4. e and turn the ignition switch to the on position 2 Press and release the valet push button switch three times NOTE Some systems may use a combination push button LED switch others may use an intergrated push button LED receiver In these systems the push button and the dash mounted LED or the receiver push button LED are one and the same 3 The LED will flash 1x and the siren will chirp 1x indicating that the system is ready to accept programming of channel 1 which is arm lock disarm unlock unlock 2 and panic functions 4 Press and hold the lock or lock unlock symbol button of the transmit ter you wish to program for 4 seconds or until a long chirp is heard from the siren Repeat step 4 for each transmitter you wish to program NOTE If your transmitter button has the Lock Unlock icon on one button press and release the valet push button switch 2 times then move on to step 8 5 Press and release the valet push button switch one time to advance to channel 2 The siren will chirp 2 times and the dash mounted LED will 128 8840 2of8 Flash 2 times indicating that the unit is ready to accept programming for channel 2 which is only used for separate lock and unlock button transmitters and is the disarm unlock unlock 2 and panic 6 Press and hold the unlock symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren Repeat step 6 for each transmi
5. he transmitter incorporates a small LED visible through the case which is used to indicate battery condition You will notice a decrease in transmitter range as the battery condition deteriorates Transmit ter battery replacement is recommended at least every 10 to 12 months depending upon how frequently the transmitter is used o replace the battery 1 Remove the 3 small 0 Phillips head screw from the rear of the case 2 Remove the rear cover to access the discharged battery paying attention to the proper polarity orientation A Carefully remove and properly dispose of the discharged battery 4 Insert the new battery close the case then reinstall the 3 small case screw removed in step 1 5 If you accidently dislodge the circuit board from the transmitter hous ing be certain that the rubber membrane is seated properly and the buttons are properly exposed from the front view of the case then insert the circuit board and return to step 4 SS91P uses CR2032 Coin Cell Type Batteries SEE ASSOCIATED DIAGRAMS ON FOLLOWING PAGE 128 8840 5of8 Remove three 0 philips head screws where indicated to gain access to the CR 2032 battery Carefully remove Retes transmitter back cover Carefully remove the discharged battery by sliding it out from under the clip in the direction indicated by the arrow in the diagram below Properly dispose of the exhausted battery and insert a new CR2032 taking care to arrange it
6. so that the is facing up toward the symbol on the battery clip This device complies with FCC Rules Part 15 Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference that may be received including interference that may cause undesired operation NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment 128 8840 6 of 8 ORDER FORM FOR SS 91 Transmitter Attention Transmitter Ordering Department i Important To help us expedite your order please print all of the amp information legibly and mail this form and your payment according to the instructions below Indicate the pad number of your transmitter selected from the pads shown above Note Transmitter model number found on back of case 1 Name 2 Address 3 4 5 City State Zip Code Telephone Number Total Number Of Transmitters Required Cost Per Transmitter is 75 00 Multiply By Number Of Transmitters X 6 Enter Total Amount Enclosed New York State Residents must include the appropriate sales tax 7 Method of Payment 0 Mastercard Q Visa L Check or Money Order do not send cash Make Checks Payable To Audiovox Corporation CreditCard Number Credit Card Expiration Date
7. tter you wish to program 7 Press and release the valet push button switch one time to ad vance to channel 3 The siren will chirp 3 times and the dash mounted LED will Flash 3 times indicating that the unit is ready to accept programming for channel 3 which is the trunk release alternate output channel of the system 8 Press and hold the trunk key symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren Repeal step 8 for each transmitter yon wish to program 9 Press and release the valet push button switch one time to advance to channel 4 if so equipped The siren will chirp 4 times and the dash mounted LED will Flash 4 times indicating that the unit is ready to accept programming for channel 4 optional device where equippe 10 Press and hold the Option button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren Repeat step 10 for each transmitter you wish to program 11 Press and release the valet push button switch one time to ad vance to channel 5 if so equipped The siren will chirp 5 times and the dash mounted LED will Flash 5 times indicating that the unit is ready to ao programming for channel 5 optional device where equippe 12 Prese and hold the second Option button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren Repeat step 12 for each transmitter you
8. uide any button or button combination can be programmed into any receiver channel Additionally if all 4 buttons are used and you require access to a 5th channel you would program a combination of buttons to control the 5th function i e you have programmed lock for arm unlock for disarm trunk for trunk release and OPT1 Sliding Door where applicable and you ve added a win dow up module that you want independent control of you would pro gram unlock and trunk buttons pressed simultaneously into the receiver to control this function independently Also if you do not program a transmitter button into channel 2 which is the separate unlock dis arm channel then whatever button is programmed into channel 1 will serve as both lock arm amp unlock disarm PROGRAMMING TRANSMITTERS NOTE Itis important to remember that during the programming mode each individual step must be completed within 15 seconds of the previous step If the 15 second time limit expires between steps the unit will automatically exit the program mode This is indicated by a long chirp from the siren Non alarm models will flash the parking lights only to confirm the transmitter code has been learned and stored NOTE Because the system may be capable of sounding a siren the vehicle horn or both where the siren chirp is referenced be low the siren may chirp the horn may beep or both devices may sound TO PROGRAM ADDITIONAL TRANSMITTERS 1 Enter the vehicl
9. will continue to be used Enter the transmitter program mode 1 Turn the ignition switch to the ON position 2 Within 10 seconds press and release the valet program switch three times Siren emits 1 short chirp indicating channel 1 has been entered 3 Within 10 Seconds press and hold the ARM or ARM DISARM button of the first transmitter you wish to remain stored into the control unit until a single chirp is heard from the siren Repeat this for each transmitter you wish to remain stored in the control unit The receiver stores up to four transmitters To be certain all transmitter slots in the receiver are occupied with transmitters you wish to con tinue to use and all others are erased you will have to fill all four receiver slots If in step 3 you identified one transmitter you will have to fill the additional 3 slots If in step 3 you identified two transmitters you will have to fill the additional two slots etc 4 Press and hold any unused button or combination of buttons until a long chirp is heard from the siren Release and press the button or button combination again and again until all remaining slots are full NOTE The button or combination of buttons entered will also control the arm or arm disarm function until additional transmitters are added All unwanted transmitters are now deleted REPRIORITIZING A TRANSMITTER S PROGRAMMING To reprogram a receiver channel with a different transmitter button once
10. wish to program 13 Within 10 seconds press and release the valet program switch one time Siren emits 6 short chirps indicating channel 6 has been entered 14 Within 10 Seconds Press and hold the unlock button or any unused button s of the first transmitter you wish to control Channel 6 output Driver Priority 1 until a long chirp is heard from the siren Repeat this for each transmitter you wish to operate the Channel 6 output Driver Priority 1 15 Within 10 seconds press and release the valet program switch one time Siren emits 7 short chirps indicating channel 7 has been entered 128 8840 3 of 8 16 Within 10 Seconds Press and hold the unlock button or any unused button s of the first transmitter you wish to control Channel 7 output Driver Priority 2 until a long chirp is heard from the siren Repeat this for each transmitter you wish to operate the Channel 7 output Driver Priority 2 NOTE Channels 6 and 7 can be used as a separate output to control a function other than driver priority Simply program ming any unused transmitter button other than the unlock button will allow complete independent control of these outputs ERASING TRANSMITTERS IF THEY HAVE BEEN LOST OR STOLEN NOTE Before you begin to erase the lost or stolen transmitter s have all transmitters available that you wish to remain programmed These will be used during the program process to identify transmitters that
Download Pdf Manuals
Related Search