AT&T 9210 User's Manual
Contents
1. make sure the dial mode is set to dial pulse see INSTALLATION If the above suggestions don t solve the problem try re initializing the handset and base Disconnect the power to the base Remove the handset battery pack Wait afew minutes Connect the power to the base Insert the handset battery pack 6 Put the handset in the base to re initialize OrPWN If you hear a two beep signal when you try to use the handset e You might be out of range Move closer to the base and try again If moving closer to the base doesn t help try following the directions above for re initializing the handset and base The handset battery charge may have become low Try charging the handset battery If the phone does not ring when you receive a call e Make sure the handset ringer is on e Make sure the telephone line cord is connected firmly to the base and the telephone jack e Make sure the AC adapter is plugged firmly into an outlet not controlled by a wall switch You might be too far from the base move closer e You might have too many extension phones on your telephone line to allow all of them to ring Try unplugging some of them DIFFICULTY If you hear noise or interference when using the phone e Make sure the base antenna is fully upright e You may be out of range Move closer to the base e Press and release to change to another of the 30 channels available If noise is exceptionally loud mo2. in base TELEPHONE MEMORY This cordless phone can store 10 telephone numbers each up to 16 digits long You can dial numbers stored in memory just by pressing MEMORY and a number button Store Memory Numbers 1 Make sure the handset is off 2 Press PROGRAM 3 Press the number button 0 9 where you want to store the telephone number 4 Dial the telephone number up to 16 digits OR Press REDIAL to store the last number dialed 5 Press MEMORY PAUSE T e Store a Pause in a Memory Number Press to store a two second pause in the dialing sequence Each press adds another two second pause and counts as one digit QoreR PROG MEMORY CHANNEL O A 6 Change Replace a Stored Memory Number Store a new number in its place f b 6 Dial Memory Numbers 1 Press PHONE 2 Press and release MEMORY then press the number button 0 9 where the memory number is stored Directory Label Use the self adhesive directory label to keep a record of the numbers or names stored in memory It s best to write on the label before applying it to the phone BATTERIES Charging the Handset Battery Pack This battery should remain charged up to six days with the ringer turned on and up to 12 days with the ringer off A fully charged battery provides an average talk time of about six hours The battery pack needs charging when e Anew battery is insta
3. REVISED 10 17 00 AT amp T USER S esi 900 MHz Cordless Telephone 9210 Fold open this manual for information about this telephone s installation and operation Please also read Part 1 Important Product Information For Customer Service Or Product Information Visit Our Website At www telephones att com AT amp T and the globe symbol are registered trademarks of AT amp T Corp licensed to Advanced American Telephones 2000 Advanced American Telephones All rights reserved Printed in Mexico 850004300 Issue 1AT amp T 10 00 INSTALLATION Before You Install 1 Choose a location for the base near an electrical outlet and a telephone jack 2 Install the handset battery Remove b Plug battery battery pack connector compartment into handset cover by pressing on the indentation and sliding downward Table Desk Installation Standard electrical outlet This phone requires a modular telephone jack and a standard electrical outlet 110v AC not controlled by a wall switch Connect the telephone line cord 2 Connect the power cord 3 Charge the handset battery Place the handset in the base Charge the battery for at least 24 hours the first time After the first charge the battery is typically fully charged overnight 4 Check for dial tone After the batteries are charged pick up the handset and press PHONE you should hear a dial tone Place battery pack and wires in compartm
4. ent Replace cover by sliding it up into place Modular telephone jack Use only the power A cord supplied with this product If you need a replacement call 1 800 222 3111 5 Set the dial mode If you have touch tone service the phone is ready to use as soon as the batteries are charged If you have dial pulse rotary service you ll need to change the dial mode When the phone is off press PROGRAM 64 Memory to set the dial mode to dial pulse To return to touch tone dialing press PROGRAM INSTALLATION Wall Installation Standard electrical 1 Connect the telephone Modular line cord telephone jack Mounting studs Connect the power cord Mount the base on the wall Align holes on base with mounting studs on wall jack Pull base down on mounting studs until it locks into place Place power cord as shown so it hangs straight down between base and wall Use only the power cord supplied with this product Follow Steps 3 5 in A If you need areplacement call 1 800 222 3111 Table Desk Installation TELEPHONE OPERATION Headset Jack You can use this telephone hands free when you install a 2 5 mm headset SKU 24099 purchased separately Plug the headset into the jack under the small rubber flap Do not force the connection but make sure the plug fits securely Handset Volume Adjust volume
5. lled in the handset The phone beeps twice when you press PHONE e The phone light flashes slowly Place the handset in the base so the CHARGING light turns on The battery pack is typically fully charged in eight hours You can keep the battery fully charged by returning the handset to the base after each use If you repeatedly get a low battery indicator even after eight hours of charging the battery should be replaced Use only Replacement battery 3301 SKU 91076 CAUTION Charge the battery provided with or identified for use with this product only in accor dance with the instructions and limitations specified in the User s Manual Part 1 Replacing the Handset Battery Pack 1 Remove the battery compartment cover on the handset by pressing on the indentation and sliding the cover downward 2 Lift out the old battery pack and disconnect 3 Plug battery pack connector into handset Place the battery pack and wires in the compartment 4 Replace the cover by sliding it up into place 5 The new battery pack must be charged before using the phone Place the handset in the base and allow it to charge for at least 24 hours the first charge The telephone might operate before that but for best performance let the battery pack charge fully OPERATING RANGE This cordless telephone operates within the maximum power allowed by the Federal Communications Commission FCC Even so this handset and base can communicate
6. of what you hear through the handset End a Call Place handset in base OR Make or Answer a Call Lift handset from base OR Press PHONE Press OFF Exit programming Flash Call Waiting Cancel a page Access special telephone company subscriber services Redial Press PHONE then press to call the last number dialed up to 24 digits Temporary Tone Dialing Press to change from dial pulse to touch tone dialing during a call This is useful if you have dial pulse rotary service and need to send touch tone signals for access to telephone banking or long distance services 1 Dial the number 2 Press Buttons pressed after this send touch tone signals 3 After you hang up the phone automatically returns to dial pulse rotary service Change Channel Switch to a clearer channel Handset Ringer Style Battery Save Select from four different handset ringer styles or turn the ringer off and extend battery life 1 Make sure the handset is off 2 Press PROGRAM 3 Press 0 or to select your ringer style you will hear a sample or press to turn the ringer off 4 Press MEMORY When the ringer is off select a ringer style to turn it on again TELEPHONE OPERATION Indicates handset is in use Page Handset Locator Press once to page the handset for up to one minute OR Press twice to cancel Indicates handset is charging
7. over only acertain distance which can vary with the locations of the base and handset the weather and the construction of your home or office For best performance keep the base antenna fully upright If you receive a call while you are out of range the handset might not ring or if it does ring the call might not connect when you press PHONE Move closer to the base then press PHONE to answer the call If you move out of range during a phone conversation you might hear noise or interference To improve reception move closer to the base If you move out of range without pressing OFF your phone will be left off the hook To hang up properly walk back into range periodically pressing GFF IN CASE OF If you have difficulty operating this phone try the suggestions below For Customer Service visit our website at www telephones att com or call 1 800 222 3111 Please retain your receipt as your proof of purchase If the phone doesn t work at all check these items first e Make sure the AC adapter is plugged into an outlet not controlled by a wall switch e Make sure the telephone line cord is plugged firmly into the base unit and the modular jack e Make sure the base antenna is fully upright If the handset does not beep when you press PHONE the battery might need charging Make sure the battery pack is installed correctly e Ifyou have dial pulse rotary service on your phone line
8. ve closer to the base before changing channels Household appliances plugged into the same circuit as the base can sometimes cause interference Try moving the appliance or the base to another outlet The layout of your home or office might be limiting the operating range Try moving the base to another location preferably on an upper floor e If the buttons don t work try placing the handset in the base for at least 15 seconds If you hear other calls while using your phone e Press to change to another channel e Disconnect the base from the modular jack and plug in a corded telephone If you still hear other calls the problem is probably in your wiring or local service Call your local telephone service company If you lose a call after changing channels You were probably almost out of range Move closer to the base before changing channels Before placing another call set the handset in the base for at least 15 seconds If you are unable to operate special telephone services or other equipment requiring touch tone signals If you have dial pulse rotary service follow the directions under Temporary Tone Dialing in the TELEPHONE OPERATION section of this manual
Download Pdf Manuals
Related Search