American Standard SPEED CONNECT 4508.4 User's Manual
Contents
1. From under side of mounting surface install VALVE BODY 3 3a through valve mounting holes Threads of VALVE BODY 3 3a should extent at least 5 16 of a inch above mounting surface top Fig A Thread DECK ADAPTER 4 onto VALVE BODIES 3 3a until snug against internal stop If necessary adjust LOCKNUT 1 Tighten LOCKNUTS 4 with WRENCH 5 supplied to secure VALVE BODIES 3 3a Cass 4 Remove ESCUTCHEON 6 WASHER 7 and am 10 UPPER GASKET 8 from TRANSFER VALVE 9 j V MOUNTING Insert TRANSFER VALVE 9 into the center forward SURFACE hole of BIDET q Em Replace UPPER GASKET 8 and WASHER 7 and ESCUTCHEON 6 until it locks against internal stop Position the side threaded outlet rearward and secure MOUNTING NUT 11 N SPRAY INSTALLATION Assemble SPRAY BODY 1 to BIDET Using putty seal underside of SPRAY BODY FLANGE 2 and secure with NUT 3 Thread SPRAY HOSE 4 with SEAL WASHER 5 to SPRAY BODY 1 Connect other end of HOSE 4 with SEAL WASHER 8 to side outlet NIPPLE 7 of the TRANSFER VALVE 8 Thread SPRAY CAP 9 onto SPRAY BODY 1 3 POP UP DRAIN Remove CLEAR PLASTIC COVER 1 Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B 4 REMOVE FLANGE B Thread FLANGE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A INSTALL DRAIN FROM BELOW FI2. 8 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST IN MEXICO 01 800 839 12 00 Product names listed herein are trademarks of American Standard Inc AS America Inc 2008
3. DECK ADAPTER Find correct position of LEVER HANDLE ASSEMBLY 4 by adjusting male teeth on ADAPTER 1 to female teeth in HANDLE 4 Thread LEVER HANDLE ASSEMBLY 4 onto DECK ADAPTER 5 until snug against mounting surface OUTLINE OF BIDET With HANDLES 1 in OFF position turn on WATER iit ZZ SUPPLIES 2 and check all connections for leaks m Operate both HANDLES 1 to flush water lines thoroughly 4 Rotate TRANSFER VALVE 5 from rim wash to spray several times to check operation W Pull up POP UP KNOB 3 and fill Bidet with water Check that DRAIN STOPPER 4 makes a good seal and retains water in Bidet If STOPPER 4 does not seal properly please refer to Troubleshooting Guide in these instructions Push POP UP KNOB 3 down and check all drain connections and P trap for leaks m Tighten if necessary 1 4 CARE INSTRUCTIONS HANDLE ASSEMBLY DO SIMPLY RINSE THE PRODUCT W To change direction of handle rotation proceed as follows CLEAN WITH GCEAR WATER DRY a Turn valve to OFF position Unthread HANDLE UNTEREAD WITH A SOFT COTTON FLANNEL BASE 1 from DECK ADAPTER 2 CLOTH a Pull HANDLE ASSEMBLY off VALVE STEM 3 a Remove SPRING CLIP 4 Lift STOP WASHER 5 DO NOT DO NOT CLEAN THE turn 90 and replace Replace SPRING CLIP 4 a Find correct position of HANDLE ASSEMBLY by adjustin PRODUCT WITH SOAPS AGID male teeth on VALVE STEM 3 to female teeth in HAND
4. INCLUDING SEALS M961634 0070A VALVE MTG KIT 030281 0070A TRANSFER VALVE MOUNTING KIT 060463 0070A ADAPTER KIT 024220 0070A COUPLING NUT M952430 0070A CABLE ASSEMBLY L M962457 007A FLANGE ASSEMBLY M922872 0070A CAM SEAT INSERT M962430 0070A CAM ASSEMBLY I M962458 0070A DRAIN MOUNTING KIT M913207 0070A TAILPIECE INSERT M962463 0020A TAILPIECE amp ESCUTCHEON M952426 YYYOA DRAIN ASSEMBLY M968845 Rev 1 2 PRINCETON BIDET FITTING LESS VACUUM BREAKER MODEL NUIVIBER 4508 400 i 918428 0070A HANDLE SCREW m M962182 YYYOA HANDLE 923348 0070A HANDLE ADAPTER 013312 YYYOA ESCUTCHEON KIT m 953800 0070A TRANSFER VALVE 0006 00 Lp SS f 028645 YYYOA BIDET SPRAY 072574 0070A EXTENSION 066116 YYYOA DRAIN STOPPER M962403 YYYOA POP UP ROD Lamy 066117 YYYOA 070847 0070A DRAIN FLANGE KIT gaara Sa B ni M961711 0070A PIVOT ASSEMBLY TAILPIECE INSERT M961656 YYYOA LIFT ROD GUIDE 030280 0040A TAILPIECE WITH ESCUTCHEON POP UP DRAIN AND LIFT ROD ASSEMBLY BEFORE 04 06 028646 0070A SPRAY HOSE CONNECTION KIT Replace the YYY with appropriate finish code CHROME 002 SATIN NICKEL 295 HOT LINE FOR HELP For toll free information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to
5. Installation Instructions PRINCETON 4508 400 Bidet Faucet and Transfer Valve with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain a feature found only on American Standard faucets Certified to comply with ANSI A112 18 1 Speed Connect Drain HUMUS ME Fewer parts installs in less time Never needs adjustment Guaranteed to seal properly the first time every time Your new American Standard faucet is designed to work only with the Speed Connect drain To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Roughing in Required tools Dimensi Sng TRANSFER VALVE FINISHED K FOR FLUSHING WALL tp BIDET OUTLINE FIM OR SPRAY c 3 IS SYMBOLIC 7 8 DIA N Screwdriver Plumbers Putty or a a ng CDOUCHE ADJ 1 1 4 2 E SPRAY N TO 2 1 4 Pg a E dH z Se eile J H MAX Phillips Screwdriver L6 FOR GROUND JOINT Channel Locks CONNECTION OR 1 2 O D SLIP INLETS REAR VIEW WITH e W WALE REMOVED Adjustable Wrench b Tubing Cutter 1 1 4 O D TAILPIECE BIDET FAUCET INSTALLATION BW en off hot and cold water supplies before beginning Place RUBBER RING 10 into ESCUTCHEON 4 Install LOCKNUT 1 and RUBBER WASHER 2 onto VALVE BODIES 3 3a
6. LE POLISH ABRASIVES HARSH Thread HANDLE ASSEMBLY onto DECK ADAPTER 2 CLEANERS OR A CLOTH WITH until snug against mounting surface A COARSE SURFACE If spout drips operate handles several times from 2 OFF to ON position Do not force handles turn anly 90 M968845 Rev 1 2 SpeedConnect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position Follow CABLE ADJUSTMENT PROCEDURE If pr icu does not raise up fully or sink drains too slowly Follow CABLE ADJUSTMENT PROCEDURE If you need to remove the Stopper Follow STOPPER REMOVAL PROCEDURE If you would like the ability to remove your Stopper simply by lifting it out of the drain Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration Fig B Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go At this point the Stopper should be in the UP position Fig B C Push DOWN on the Lift Knob to make sure it is fully down Fig C Re attach the Cable to the Drain Body Connection 2 by threading the Cable Connector 1 clockwise onto the Drain Body Connection 2 and hand tighten Fig A STOPPER REMOVAL PROCEDURE Di
7. NSTALL DIVERTER KNOB Push DIVERTER KNOB 1 onto HANDLE ADAPTER 2 Push on RING 3 and tighten with SCREW 4 Press on KNOB CAP 5 Note Screwdriver gap is for disassembling and should point downwards OUTLINE OF BIDET Insert SEAL 1 into ADAPTER 2 and tighten ADAPTER 2 to side of TRANSFER VALVE 3 Install SEAL 4 into coupling nut of TEE 5 and tighten connection to ADAPTER 2 Connect HOSE COUPLING NUTS 6 to Hot and Cold valve bodies and securely tighten 9 3 8 O D BULL NOSE WATER SUPPLY CONNECTION THREAD x RISERS COMPRESSION NUT NOTE FLEXIBLE SUPPLIES OR BULL NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY 2 Connect water supply to VALVE BODIES 7 7a with FLEXIBLE 1 2 IPS FLEXIBLE SUPPLIES 8 or 3 8 0 D BULL NOSE RISERS 9 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink copper supply when bending Use tubing cutter to cut to proper length Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant appropriate N 7 M CONNECT TO connectors and COUPLING NUTS e WASTE OUTLET Connect 1 1 4 O D tailpiece on POP UP DRAIN to 3 8 COMPRESSION waste outlet CONNECTION M968845 Rev 1 2 INSTALL HANDLES B Push ADAPTER 1 on VALVE STEM 2 so that the hole of the ADAPTER 1 without a spline is facing up See figure A Tighten THREAD ON STEM SCREW 3 to secure ADAPTER 1 TO
8. XTURE From under side of BIDET Tighten LOCKNUT 1 firmly with Adjustable install DRAIN BODY 1 up Wrench or Channel Locks through drain outlet Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the BIDET Install FOAM GASKET 3 and FLANGE 4 onto drain body from above BIDET and tighten FLANGE 4 firmly FLANGE GASKET Check DRAIN FLANGE in BIDET to ensure that WHITE FOAM GASKET 1 is fully compressed and not visible Fig A POP UP ROD ASSEMBLY Insert LIFT ROD GUIDE 1 and CABLE CONNECTOR 2 SLOTTED MOUNTING N UT through rear hole making sure SEAL WASHER 3 is properly seated Fig B e 4 IAS ILLUSTRATION NOT VISIBLE SHOWN LESS 2 From below slip slot in MOUNTING NUT 4 over CABLE 5 VALVES Thread NUT 4 onto lift rod guide shank to secure ROD GUIDE 11 to bidet Hand tighten only Fig B M968845 Rev 1 2 ATTACH CABLE CONNECTOR POP UP KNOB 1 must be fully down Fig A Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig B Your new POP UP DRAIN installation is now complete Fig C Note Tailpeice on pop up drain 1 1 4 O D is 1 1 4 O D Fig C CHECK OPERATION OF POP UP Operate LIFT KNOB 1 to verify that STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions I
9. e See CABLE ADJUSTMENT PROCEDURE in Locked Mode Troubling Shooting Guide to complete installation Stopper will be Vandal Proof in Locked mode and not be removable Unlocked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig H To install the stopper in Unlocked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig H Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J lt LOOP TOWARD Re install the Cam Cap making sure the guide teeth are facing FRONT OF BIDET outward If the Cam Cap does not snap into place then rotate the Cam to make sure it is fully inserted Fig K Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Unlocked Mode Troublingshooting Guide to complete installation Stopper will be in Unlocked mode and removable INSTALL CAM CAP M968845 Rev 1 2 Yimuritau Standard LD M962404 YYYOA HANDLE KIT M962248 0070A DECK ADAPTER KIT M962481 YYYOA LIFT ROD GUIDE 918555 0070A 3 HANDLE SCREW 918049 0070A ADAPTER H 994053 0070A 2 CARTRIDGE M9682475 YYYOA POP UP ROD ew DD t 033772 0070A TEE AND HOSE KIT me
10. sconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration Fig B Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain Fig D Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal Fig E The Stopper can now be removed by lifting it out of the Drain Fig F CAM REMOVE CAM CAP M968845 Rev 1 2 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways Locked Mode Stopper cannot be removed or Unlock Mode Stopper is removable Locked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig G To install the stopper in Locked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig G Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J Re install the Cam Cap making sure the guide teeth are facing SM n esa Peipin ek outward If the Cam Cap does not snap into place then rotate the Cam to make sure it is fully inserted Fig K Re attach Cabl
Download Pdf Manuals
Related Search