Aiphone AN-8000EX User's Manual
Contents
1. 192 stations for one CR 413 and 1 280 stations for seven CR 413s For the CR 273 and CR 413 Equipment rack assembly or BU 412 Blower unit installation read the installation manual supplied with the rack Note When installing the blower units terminal boards and exchanges lay the equipment rack down face up to do installation work safely Since the blower unit is installed from the inside of the rack be sure to install it first before mounting the other components Exchange 7 1 1 Setting space For maintenance works allow much space between the wall and Equipment rack 7 1 2 Caution when installing the unit Do not block the fan exhaust vent Doing so may cause heat to build up inside the AN CAUTION unit and result in fire Do not stack up 3 Exchanges or more If 2 or more Exchanges are mounted in the Equipment rack be sure to mount the perforated panel of 1 U size PF 013B or more above and below every 2 Exchanges ss Equipment rack Exchange sete hiv Using the supplied rack mounting screws install the E terminal board in a location that facilitates wiring and maintenance work taking into consideration the direction of cable entry into the rack 7 1 3 Mounting on the rack eS AN 8000EX Rack mounting bracket accessory 27 i Step 1 install the rack mounting bracket to the j Tapping screw 3 x 8 Exchange j accessory Step 2 Mount the Exchange on the Equipment rack Rack mount2. Note D Lines shouid be twisted If there is a danger of lightning strikes insert an appropriate power gap arrester into the power line Both upper and lower terminals clip terminals are internally connected E 7000TB Terminal board Station Select an appropriate UPS taking into consideration the total power consumption of all system components and the required backup time and aiso the requirement that the UPS should employ the on line power system Reference Exchange Maximum 50 W 8 Port 10M 100M Switching Hub 10W Differs depending on products AN 8000EX Exchange PAGING OUT1 PAGING OUT2 AUDIO CONTROL AUDIO CONTROL seq 71 71 10 100M RJ45 connector To network Removable terminal plug accessory 4 Control input PA Paging amplifier etc gren edema H i x 1 NS i 3 Line input General description of connection For cables refer to p 12 1 Power supply connection 4 Paging contact output terminal connection Connect the supplied power supply cord to AC Mains or a UPS Uninterruptible power supply feeder About power supply cord handling The supplied power supply cord is designed for exclusive use with the AN 8000EX Use the supplied power supply cord only with the Exchange Line terminal connection The line terminals have no polarity Refer to p 13 Connector connection Paging audio output terminal connection Paging
3. Dedicated Tool down onto the terminal from above Pressing down the YC 105 tool cuts off the excess cable end securing the connection For cables refer to p 12 Type of Cable Clipping tool YC 105 Optional Yellow ee m G ray Hook the cable onto i the termina without i stripping the cladding wee Cut end ss Terminal Terminal board E 7000TB E i mE M Saaste Bind the cables using cable m clips supplied with the E7000TB o 2 pn El 4L 9 ACCESSORIES Power supply cord 2 m cccsecseserseeree eee 1 Rack mounting bracket eeeeeee 2 O D imer PL E E E 1 Tapping screw 3 X 8 uscito erem eneee six pero uice 8 Removable terminal plug 4P 2 Rack mounting screw 5 x 12 Mini clamp connector 2P asenenc 20 with plain washer suse iro rn er HE REEF reed 4 Plastic TOOL Sorire iii dedu uris oU ere 4 Wall mounting bracket esessese 2 Machine screw M4 x 20 sseeseeesese 4 Wood screw 3 5 X 20 1 Lee rer vestra etri 4 Contains the AN 8000 setting software program and the AN 8000 series instruction manual The Setup Launcher is automatically started when the supplied CD ROM is inserted into the PC s drive Note If your PC s CD drive is not compatible with the AutoRun function the setup guide is not automatically started even when the CD is inserted Use either Explorer or My Computer to exec
4. installation 7 1 Rack Mounting A Elevated Operating Ambient If installed in a closed or multi unit rack assembly the operating ambient temperature of the rack environment may be greater than room ambient Therefore consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature Tma specified by the manufacturer B Reduced Air Flow Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised C Mechanical Loading Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading D Circuit Overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring Appropriate consideration of equipment nameplate ratings should be used when addressing this concern E Reliable Earthing Reliable earthing of rack mounted equipment should be maintained Particular attention should be given to supply connections other than direct connections to the branch circuit e g use of power strips The Exchange can be mounted on the CR 273 or CR 413 or standard EIA 19 Equipment rack These racks when fuily equipped with exchanges can provide the following capacity of stations 128 stations for one CR 273
5. power cord to an AC in personal injury and or property damage outlet use the AC outlet with current capacity allowable to the unit 2 GENERAL DESCRIPTION AIPHONE s AN 8000EX is an exchange used for the AN 8000 Series Network Intercom System IP network compatible intercom employing packet audio technology By connecting IP intercom exchanges which permit connection of up to 16 stations per exchange to a network LAN or WAN an optimal system for in house or wide area information communications such as duplex conversations between stations and paging broadcasts can be constructed Since up to 80 exchanges can be combined systems of up to a total of 1 280 stations can be realized The system s echo cancellation feature makes hands free duplex conversation possible conversations made without using a handset at both parties between stations Technology related to audio transmission over a network A circuit that prevents acoustic feedback or echo generated when the voice output from the station s internal speaker enters the microphone Warning This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures 3 FEATURES e Exchanges can be distributed over a data communications network e Can be connected to an existing local area network LAN or wide area network WAN The system can also be easily connected to fiber optic netw
6. 000TB Terminal Board Wining 5i et laces e Eee deco e bietet 18 d ACCESSORIES osten uua Rusia e aoc om d 16 1 SAFETY PRECAUTIONS e Before installation or use be sure to carefully read all the instructions in this section for correct and safe operation Be sure to follow all the precautionary instructions in this section which contain important warnings and or cautions regarding safety e After reading keep this manual handy for future reference Safety Symbol and Message Conventions Safety symbols and messages described below are used in this manual to prevent bodily injury and property damage which could result from mishandling Before operating your product read this manual first and understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards A WARNING CAUTION WARNING When installing the Unit a e Do not expose the unit to rain or an environment where it may be splashed by water or other liqu ds as doing so may result in fire or electric shock Use the unit only with the voltage specified on the unit Using a voltage higher than that which is specified may result in fire or electric shock Do not cut kink otherwise damage nor modify the power supply cord In addition avoid using the power cord in close proximity to heaters and never place heavy objects including the unit itself on the power cord as doing so may result in fire or electric shock A
7. audio output terminals have no polarity Refer to p 14 Removable terminal plug connection Specification of paging audio output 0 dB 600 2 balanced Paging contact output terminals have no polarity Refer to p 14 Removable terminal plug connection Specification of paging contact output No voltage make contact output Withstand voltage Max 24 V DC Control current Max 0 5 A Network connection Can be connected to a network of 10BASE T 100BASE TX in auto sensing Use a UTP category 5 straight through cable for this connection Station connection The connection method differs depending on types of stations For details refer to the instruction manual supplied with each station OdB 1V 44 12 8 2 Type of Cable The types of cables are to be determined according to the following conditions Twisted pair wires such as those used for electronic push button telephone are to be used for wiring between the Exchange and the stations in principle UTP category 5 Straight through cables with RJ45 connector are to be used for wiring the equipments connected to IP network The number of cables pairs laid should be determined considering the possibility of future expansion of the system Outdoor wires should be used where wiring passes through inaccessible areas such as ceilings or under floors where the maintenance is not performed indoor wires may also be used however in case where
8. fire AC inlet Connects the supplied power cord Note If there is a danger of lightning strikes insert an appropriate surge arrester into the power line Cord clamp Pass the power cord through this clamp to ensure that the plug cannot be pulled out when the unit is mounted to a wall Refer to p 9 Power indicator POWER Green Lights when power is supplied to the exchange MAC address This is the address used by the exchange Since the relationship of each exchange location to its MAC address is established when setting the network attributes keep track of this relationship for later use The inherent address assigned to each network component expressed in 12 digit hexadecimal notation PAGNG OUT PAGING QUT2 AUDO CONTROL AUDO CONTROL 10 1004 FILM DM Ld d E i E 10 Line connection terminal LINE 11 12 Connect the station to each terminal using a mini clamp connector Refer to p 13 Paging output terminals PAGING OUT 1 2 AUDIO CONTROL Includes audio outputs 0 dB 600 O balanced and contact outputs no voltage make 24 V DC 0 5 A MAX Connect using a removable terminal plug Refer to p 14 Network connection terminal 10 100M Connects a 10BASE T or 100BASE TX compatible network Ethernet RJ45 jack OdBz1V 7 INSTALLATION The exchange can be installed in any of three ways 1 rack mounting 2 wall mounting and 3 desk top
9. ing screw 5 x 12 with plain washer accessory 7 2 Desk Top Installation When installing the Exchange on a desk secure the supplied plastic feet to bottom surface of the Exchange using the supplied machine screws Machine screw M4 x 20 E i N Plastic foot accessory a od Au 8000EX lt 7 3 Wall Mounting Step 1 Install the supplied wall mounting bracket to the Exchange using each 2 supplied screws and removed screws from the case Wall mounting bracket accessory AN 8000EX 7 Tapping screw 3 x 8 amp w removed from the case Tapping screw 3 x 8 accessory Siep 2 Mount the Exchange on the wall Notes Use appropriate screws for the construction of wall Wood screws 3 5 x 20 are supplied with the AN 8000EX e The socket outlet shall be installed near the equipment and shall be easily accessible Protect against disconnection Power supply plug Unlock cord clamp and run the power supply cord through it Note Keep the cable length between a power supply plug and cord clamp as short as possible Uf Power supply cord Cord clamp AN Wood screw 3 5 x 20 accessory d 10 8 WIRING 8 1 Connection Diagram AN 8000EX Exchange LINE 16 lines 232D 0281B DAS L i Mini clamp connector DDK i To AC mains or a UPS accessory i Uninterruptible power supply system j
10. ions AN 8000MS AN 8010MS AN 8011MS AN 8020MS AN 8031MS RS 191 AN 8050DS Others YC 280 YC 290 YC 241 YC 251 YC 150 YS 13A E 7000TB CHR 273 CR 413 IP intercom Exchange Multifunctional Master Station Standard Master Station Standard Hands Free Master Station industrial Use Master Station Flush Mount Master Station Option Handset Door Station Wall mounting bracket for the AN 8000MS 8010MS 8020MS Wall mounting bracket for the AN 8011MS Back box for the AN 8031MS Wall mount box for the AN 8031MS Back box for the AN 8050DS Wall mount box for the AN 8050DS 40 Station Terminal Board Equipment Rack Equipment Rack 6 NOMENCLATURE AND FUNCTIONS Front AIPHOHE RESET LNGACT STATUS POWER oo Q4 Qed Qes DO 05 F9 FF 00 CQ tte ette i Reset key RESET Pressing this key reactivates the exchange LNK ACT indicator LNK ACT Green Lights when connected to a network and flashes while transmitting or receiving data Status indicator STATUS Red Continuously lights while data is written to an internal storage medium FlashMemory and flashes to indicate such exchange malfunctions as cooling fan failure 6 Functional earth terminal SIGNAL GND Ground this terminal Note This terminal is not a safety ground Cooling fan A CAUTION Do not block the fan exhaust vent Doing so may cause heat to build up inside the unit and resuit in
11. nsert the cable without stripping the cable jacket wee For cabies refer to p 12 Type of Cable TS Step 2 With a pair of pliers lightly pinch the mini clamp cover b 4 and after ensuring that the cable is securely inserted firmly squeeze on the cover Note Squeeze on the mini clamp cover until it is correctly locked O Step 3 Insert the wired connector plug into the exchange s connector socket until it locks into place AN 8000EX Rear panel 49 14 8 4 2 Removable terminal plug connection Step 1 Strip a cable jacket of approx 7 mm to expose inner cable 7 mm For cables refer to p 12 Type of Cable a Note Do not solider plate on exposed inner cables when using a stranded wire Step 2 Loosen the terminal screws and insert the cables Step 3 Tighten the terminal screws securely Notes e Tug lightly on the cable to be sure that it does not pull free If the cable pulls free loosen the terminal screw again and reconnect from Step 2 e Use the screwdriver appropriate to the screws tightened into the terminal plug Step 4 Insert the wired terminal plug into the terminal block of the Exchange AN 8000EX rear panel Removable terminal plug accessory 8 5 E 7000TB Terminal Board Wiring For cable connection to the E 7000TB Terminal Board use the optional YC 105 clipping tool Hook the end of the cable onto the terminal and with the cable end in hand press the YC 105
12. orks without restrictions on operating distance e The dedicated software program enables centralized control with a personal computer e System maintenance verifying operation log and Line supervision can also be performed with a personal computer and Internet browser 4 SPECIFICATIONS Number of Exchanges connectable to LAN Maximum 80 Line Capacity Maximum 1 280 80 Exchanges x 16 stations per Exchange Speech Link Capacity Internal 4 links External Speech Link maximum 8 links Multicast paging Link maximum 4 links Unicast paging 1 link simultaneous access capacity Paging Zones Capacity Maximum 160 With 80 Exchanges Paging Zone Maximum 79 Multicast paging Maximum 16 Unicast paging System Settings Personal computer setting using a dedicated software program over LAN Network Related Voice delay time 80 or 320 ms selectable Usage bandwidth Maximum 2 08 Mbps one way when 16 Unicast pagings are made Maximum 130 kbps two way per call 5 SYSTEM CONFIGURATION EXAMPLE MC KT DAR foci o AIPHONE o 9 9 To LAN AN 8000EX Amplifier Speaker LES Os LY UPS DH To AC Mains Uninterruptible power supply feeder LLR S020 ooo CCCo CIID O Hal i Z e wH 0000000 See ETEBRTEHEFEIEEFTEHIT ES iti j ACORDADO adc TM TEN AN 8000MS AN 8010MS AN 8011MS AN 8020MS RS 191 AN 8031MS AN 8050DS fExchange AN 8000EX Stat
13. rop metallic objects or flammable materials in the ventilation slots of the unit s cover as this may result in fire or electric shock e Do not touch a plug during thunder and lightning as this may result in electric shock A CAUTION When installing the Unit Never plug in nor remove the power supply plug with wet hands as doing so may cause electric shock e When unplugging the power supply cord be sure to grasp the power supply plug never pull on the cord itself Operating the unit with a damaged power supply cord may cause a fire or electric shock e Do not block the fan exhaust vent on the unit s rear Doing so may cause heat to build up inside the unit and result in fire Be sure to follow the instructions below when rack When the Unit is in Use mounting the unit Failure to do so may cause a fire or personal injury Do not place heavy objects on the unit as this may cause it to fall or break which may result in personal injury and or property damage In addition the object itself may fall off and cause injury and or damage Install the equipment rack on a stable hard floor Fix it with anchor bolts or take other arrangements to prevent it from falling down To mount the unit on the equipment rack CR 273 or CR 413 use the rack mounting hardware Do not stand or sit on nor hang down from the unit supplied with the unit as this may cause it to fall down or drop resulting When connecting the unit s
14. there is no risk of deterioration due to exposure to heat etc Note Specifications related to each junction are as follows Mini clamp connector AN 8000EX line terminal Conductor diameter 0 4 0 65 mm AWG22 26 Solid wire Outside diameter 1 05 mm or below Clip terminal E 7000TB Conductor diameter 0 4 0 8 mm AWG20 26 Solid wire Outside diameter 9 1 5 mm or below Removable terminal plug AN 8000EX Paging output Conductor diameter 0 5 2 mm AWG12 24 Solid wire Stranded wire 8 3 Relations Between Core Diameter of Cable and Maximum Cable Length Refer to the following table as guidelines when designing the distance between the Exchange and stations so that loop resistance value becomes 170 Q or less Conductor diameter Loop resistance Maximum cable length between the Exchange and station mm I Assuming that the foop resistance is 170 Q 8 4 Connector Connection Mini clamp connectors for line terminals and detachable terminal plugs for paging output terminal are supplied with the AN 8000EX Exchange Perform each connector connection as follows 8 4 1 Mini clamp connector connection Connect the mini clamp connector supplied with the AN 8000EX to a cable using a commercially available tool pliers Step 1 Cut off two cable ends in equal fength and insert them Cover transparent side N securely to a cover section transparent side of the mini clamp connector Note I
15. ute the following files or use Start Run in the Task Bar and enter the following command Drive where CD is placed Mndex html For example when placing the CD in the d drive d index htm Version update information eee Please contact to the AIPHONE sales office to obtain the up to date version for firmware software and the instruction manuals e The software version number can be confirmed using the Help menu The current firmware version can be confirmed on the system management screen displayed when the browser establishes the connection to the Exchange e The instruction manual version number can be confirmed by checking the preparation date month and year shown at the lower right corner of the last page Example Prepared in November 2004 200411 Zh ATR REO
16. v Al PHON E INSTALLATION MANUAL IP INTERCOM EXCHANGE AN 8000EX Thank you for purchasing AIPHONE s IP Intercom Exchange Please carefully follow the instructions in this manual to ensure long trouble free use of your equipment TABLE OF CONTENTS 1 SAFETY PRECAUTIONS 2 eene ces 3 2 GENERAL DESCRIPTION eerte tetra trees 4 S PEAPUHES L ace n dete drei tuni ast tte ime E p e 4 a SPECIFICATIONS desc bim e E e E ese eet Die D d 4 5 SYSTEM CONFIGURATION EXAMPLE eanna 5 6 NOMENCLATURE AND FUNCTIONS re 0 RR ERREUR ick a abus dct Gods EATA EAE E E 6 ic MR ios E das tpg wae Siena sn dio Ws vi Galea alin wee bu Bone soe Gua ghee So th vena Wiad hes Sout 6 7 INSTALLATION 7 1 Rack Mounting DONG Mis SERING SPACE C CCP f 7 1 2 Caution when installing the unit iion eoo oe qui tertie aU doe OU eo Pe Rc ceca ts 7 7 1 3 Mounting on the TACK acaios fapseilecatentassn rue ea RADO C em D Es 8 722 Desks TOD UVStAN ANON soit d deat FEED as ert rese devote Ped 8 e mr M MOUNT a T T 9 8 WIRING 8 1 Connection Diagram s uoces eb etu epe oder ce teme tu te adve osea EOD ea 10 8 2 TVDe Ol CANS cose Me pw CE E p C f 12 8 3 Relations Between Core Diameter of Cable and Maximum Cable Length 12 8 4 Connector Connection 9 4 1 Mini clamp connector Connection iiiioa oec itane exar re eura eed Pare 13 8 4 2 Removable terminal plug connection sssseeeee 14 8 5 E 7
17. void installing or mounting the unit in unstable locations such as on a rickety table or a slanted surface Doing so may result in the unit falling down and causing personal injury and or property damage Install the unit only in a location that can structurally support the weight of the unit and the mounting bracket Doing otherwise may result in the unit falling down and causing personal injury and or property damage When the Unit is in Use Should the following irregularity be found during use immediately switch off the power disconnect the power supply plug from the AC outlet and contact your nearest AIPHONE sales office Make no further attempt to operate the unit in this condition as this may cause fire or electric shock indicates a potentially hazardous situation which if mishandled could result in death or serious personal injury Indicates a potentially hazardous situation which if mishandled could result in moderate or minor personal injury and or property damage If you detect smoke or a strange smell coming from the unit lf water or any metallic object gets into the unit If the power supply cord is damaged exposure of the core disconnection etc If it is malfunctioning no tone sounds TO prevent a fire or electric shock never open nor remove the unit case as there are high voltage components inside the unit Refer all servicing to your nearest AIPHONE sales office e Do not insert nor d
Download Pdf Manuals
Related Search