Benq FP73G, 17", 1280x1024 (SXGA), 16.2 million colours
Contents
1. The image is distorted flashes or flickers C Read the How to adjust the screen resolution on page 20 section and then select the correct resolution refresh rate and make adjustments based on these instructions The image is displaced in one direction 3 Read the How to adjust the screen resolution on page 20 section and then select the correct resolution refresh rate and make adjustments based on these instructions Need more help If your problems remain after checking this manual please contact your place of purchase or e mail us at Support BenQ com Troubleshooting 33 Supported opearting modes Incoming display mode Input timing Resolution Horizontal Vertical Pixel Comment Frequency KHz Frequency Hz Frequency MHZ 25 16 832x624 49 72 N 74 55 N 57 29 1024x768 48 36 N 60 00 N 65 00 VESA 1024x768 56 48 N 70 10 N 75 00 VESA P N 18 75 VESA N 108 00 135 00 e Modes not listed in the table may not be supported For an optimal picture we recommended you choose a mode listed in the table above e There are 22 available modes that are compatible with Windows e Image disruption may occur as a result of signal frequency differences from graphic cards which do not correspond with the usual standard This is not however an error You may improve this situation by altering an automatic setting or by manually changing the phase setting and the pixel frequency from the2. Geometry menu e Ifyou switch off the monitor interference lines can occur on your screen But do not be concerned about this as it is normal e To extend the service life of the product we recommend that you use your computer s power management function 34 Supported opearting modes Specifications BenQ FP73G Model Display type Viewable diagonal Native maximum resolution Colors Contrast Brightness Response time Viewing angle left right up down Line frequency Image frequency Image diagnostics Controls Functions Power management Max power consumption Standby power consumption Input signal Synchronization Temperature operating Air humidity operating Certifications FP73G 17 0 active TFT 432 mm 1 280 x 1 024 16 2 million 700 1 300 cd m2 6 ms 150 140 CR 10 170 170 CR 5 30 82 kHz Multi frequency monitor 56 76 Hz modes within these parameters Digital OSD Technology iKey automatic image setting 5 buttons and iKey Contrast brightness vert amp hor image position phase pixel clock color balance color palette multiple language OSD OSD position status indicator input selection VESA DPMS EPA 40 Watt lt 1 Watt 120 V lt 2 Watt 240 V RGB analog 0 7 Vpp 75 Ohm positive Digital DVI D optional TTL separate signal connection 15 pin mini D sub cable 0 C 40 C This product comply with ENERGY STAR Program Requireme
3. If there is only one monitor in the list it will already be selected for you Click the Properties button The Monitor Properties window will display If the driver provider is listed as BenQ and the model matches that of your new monitor the proper drivers are already installed and you need do nothing further Cancel out of these property windows However if BenQ is not listed as the manufacturer or the correct model is not currently shown you will need to continue with these instructions Click the Driver tab and the Update Driver button The Hardware Update Wizard will display Follow the wizard instructions noting the steps below Insert the BenQ LCD Monitor CD ROM into a CD drive on the computer you attached the monitor to Check the option Install from a list or specific location and click Next Check the option Search for the best driver in these locations and also check Search removable media then click Next Please wait while the wizard searches for drives and the BenQ LCD Monitor CD inserted in step 6 When complete the wizard should have found and selected the BenQ driver on the CD appropriate to your monitor model in this case BenQ FP73G in the location d driver BenQFP73G inf or similar The drive letter for your CD drive may differ from the example above depending upon your system it may be D or E or F etc Select single click the file named B
4. and it will have entered the address to the BenQ LCD Monitor CD Driver folder into the field titled Copy manufacturer s files from The field will contain something like D Driver or E Driver or F Driver Click the OK button This will return you to the Upgrade Device Driver Wizard Select single click the file named BenQ FP73G and click the Next button Click Next This will copy the appropriate monitor driver files to your computer Click Finish On Windows 2000 this will close the wizard and return you to the Monitor Properties window now renamed BenQ FP73G Properties Should you wish to do so this is where you can change the screen refresh rate and other monitor properties to suit your needs See How to adjust the screen refresh rate on page 21 for details In Windows 2000 click Close This will close the BenQ FP73G Properties window and return you to the Advanced Display Properties window In Windows 2000 click OK This will close the Advanced Display Properties window and return you to the Display Properties window Should you wish to do so this is where you can change the screen resolution area and color See How to adjust the screen resolution on page 20 for details Click OK Getting the most from your BenQ monitor This will close the Display Properties window and if you made any changes to the screen resolution Windows 2000 will prompt you for confirmation to effect
5. left or P right keys to highlight a menu item and press the Enter key to display the Menu item settings Main Menu Main Menu Auto Setup kEm OSD Luminance ut Language e Geometry L2 j Recall l Color a Miscellaneous Luminance sub menu Luminance Brightness Contrast Press the or P keys to adjust the degree of Brightness Luminance Press the Exit key to return to previous menu Brightness ee gt S25 Press the or P keys to adjust the degree of Contrast Luminance Press the Exit to return to previous menu suns Contrast ee gt SCO How to adjust your monitor 25 Geometry sub menu Geometry H Position V Position Press the or P keys to adjust the display Horizontal Position Press the Exit key to return to previous menu Press the or P keys to adjust the display Vertical Position Press the Fxit key to return to previous menu Press the or P key to adjust the monitor Pixel Clock Press the Fxit key to return to previous menu Press the or P keys to adjust the degree of screen display Phase Press the Fxit key to return to previous menu How to adjust your monitor Geometry H Position gt SCO Geometry V Position lt EG gt 5o Geometry Pixel Clock lt EG gt SCO Geometry Phase eu gt SC30 Color sub menu Bluish Reddish Normal User Preset Bluish_ applies a cool tint to the image and is
6. monitor eee eseeeeecceecceecceeccesccesccesscesecesscensceseeeses 13 How to install the monitor on a NEW computer seessessesssesessresseesssesssessseessresssessees 14 How to upgrade the monitor on an existing COMPUEE eee eeeseeeeseeeseeeeceeeeeeeees 15 How to installon Windows XP Systeri iersinii eaei 16 How to install on Windows 2000 system ccsssccsscccesecsecesesceseeceseeceseeeseseeseeeesees 17 How to complete the Windows Upgrade Device Driver Wizard ceesceseseeeees 18 Howto adjust the Screen TESOUTION sorserien a E eisi 20 How to adjust the ser en refresh rate suiriri ea A E E 21 How to set the picture Optimizanon ssia oa a aa 22 Howto adut your Monitor anea n R RA 23 A lookatthecontrorpane ss E EA 23 Hotkey MONE a E E AN 24 Miminen iR E aee TET TEE E N cect en ie 25 Troubleshooter E AEE E E T Hee ea eewnese 32 Frequently asked questions FAQ essessssssesssessssssesssesseessesssesseessesssesseessesseesseessesses 32 AEO on o E A ere ar EA EEE EET 33 Supported O Pearle MO GES atire rA E O E RN 34 OPEC 8 ar 10 S ar E EN EEE 35 Table of Contents 3 Getting started When unpacking please check you have the following items If any are missing or damaged please contact the place of purchase for a replacement BenQ LCD Monitor Quick Start Guide CD ROM Power Cord signal Cable D Sub Signal Cable DVI D optional N 7 Q Consider keeping the box and packaging in storage fo
7. BenQ FP73G LCD Color Monitor 17 0 LCD Panel Size User s Manual Welcome Copyright Copyright 2006 by BenQ Corporation All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of BenQ Corporation Disclaimer BenQ Corporation makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties merchantability or fitness for any particular purpose Further BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of BenQ Corporation to notify any person of such revision or changes Please follow these safety instructions for best performance and long life for your monitor Power Safety e The AC plug isolates this equipment from the AC supply e The power supply cord serves as a power disconnect device for pluggable equipment The socket outlet should be installed near the equipment and be easily accessible e This product should be operated from the type of power indicated on the marked label If you are not sure of the type of power available consult your dealer or local power company Care And Cle
8. aning e Cleaning Always unplug your monitor from the wall outlet before cleaning Clean the LCD monitor surface with a lint free non abrasive cloth Avoid using any liquid aerosol or glass cleaners e Slots and openings on the back or top of the cabinet are for ventilation They must not be blocked or covered Your monitor should never be placed near or over a radiator or heat source or ina built in installation unless proper ventilation is provided e Never push objects or spill liquid of any kind into this product Servicing e Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltages or other risks If any of the above mentioned misuse or other accident such as dropping or mishandling occurs contact qualified service personnel for servicing Table of Contents COPING SSLARLCC cece cto scares 5 tetera E A cared cde cas A E E E 5 Gettin gs TO KMOW VOUT THOM OF serros a Ee i aaa a 6 FROM VIGW scisdedetvsuactesusasisdusssudaiveudencdenedaduccnuerbsuseuusasnnuuabeeeesvanaeeeeuaaseseuuaaseteusesedesstonenenee 6 BAEN Gi ere eer rere TCE SEE nee Ere DUR eR NCTE ere eet eee 6 How to assemble your monitor hardware sccssccsssccsscessccescesecsesecessecssecesecceneceseesenseens 7 How to detach the stand base 2 5055 ckide dn danse anene 10 How to use the monitor wall mounting kit eseessseseeessesssessressesssessressesssessesseessesses 1 Getting the most from your BenQ
9. at even surface a N Q You should position the monitor and angle the screen to minimize unwanted reflections from other light sources How to assemble your monitor hardware 7 2 Connect the PC video cable Either gt Do not use both DVI D cable and D Sub cable on the same PC The only case in which both cables can be used is if they are connected to two different PCs with appropriate video systems Connect one end of the DVI D cable to the monitor DVI D socket and the other end to the DVI D port on your computer optional 7 The DVI D format is used for direct digital connection between source video and digital LCD monitors or Or projectors The digital video signals produce a superior quality picture than analog video signals O Connect the plug of the D Sub cable at the end without the ferrite filter to the monitor D Sub socket Connect the other plug of the D Sub cable at the end with the ferrite filter to the computer video D Sub socket Tighten all finger screws to prevent the plugs from accidently falling out during use 3 Connect the power cable to the monitor Plug one end of the power cord into the socket labelled POWER IN on the rear of the monitor Do not connect the other end to a power point just yet 8 How to assemble your monitor hardware 4 Route the cables via the cable clip Release the cable retaining clip by squeezing the clip inwards as illustrated Position t
10. ch its Found New Hardware wizard Follow the wizard instructions until it asks you to select a monitor model At that point click the Have Disk button insert the BenQ LCD Monitor CD ROM and select the appropriate monitor model Further details and step by step instructions for both an automatic new or upgrade existing installation follow See e How to install the monitor on a new computer on page 14 e How to upgrade the monitor on an existing computer on page 15 gt If you require a User Name and Password to login to your Windows computer you must be logged on as an Administrator or as a member of the Administrators group in order to install the monitor driver software Furthermore if your computer is connected to a network which has security access requirements network policy settings may prevent you from installing software on your computer Getting the most from your BenQ monitor 13 14 How to install the monitor on a new computer This instruction details the procedure for selecting and installing the BenQ LCD Monitor driver software on a new computer which has never had a monitor driver installed before This instruction is only suitable for a computer which has never been used before and for which the BenQ LCD Monitor is the first ever monitor to be connected to it If you are adding the BenQ LCD Monitor to an existing computer that has already had another monitor connected to it and has monitor driver software install
11. ed you should not be following these instructions You should instead be following the instructions for How to upgrade the monitor on an existing computer 1 Follow the instructions in How to assemble your monitor hardware on page 7 When Windows 2000 or later starts it will automatically detect the new monitor and launch the Found New Hardware Wizard Follow the prompts until it displays the option to Install Hardware Device drivers 2 Insert the BenQ LCD Monitor CD ROM into a CD drive on the computer 3 Check Search for a suitable driver for my device option and click Next 4 Check the option for CD ROM drives uncheck all others and click Next 5 Look to confirm that the wizard has selected the correct name of your monitor as BenQ FP73G and click Next 6 Click Finish 7 Restart the computer Getting the most from your BenQ monitor How to upgrade the monitor on an existing computer This instruction details the procedure for manually updating the existing monitor driver software on your Microsoft Windows computer It is currently tested as compatible and recommended only for Windows 2000 and Windows XP Operating System OS gt The BenQ LCD Monitor driver for your model may well function perfectly with other versions of Windows however as at the time of writing BenQ has done no testing of this driver on other versions of Windows and cannot guarantee its operation on those systems Installing monitor drive
12. ellaneous Input Select D sub Miscellaneous Sharpness Sharp 72 3 4 5 Soft Miscellaneous Display Information 1024 x 768 60 Hz How to adjust your monitor 31 Troubleshooting Frequently asked questions FAQ The image is blurred 3 Read the How to adjust the screen resolution on page 20 section and then select the correct resolution refresh rate and make adjustments based on these instructions 3 How do you use a VGA extension cable Remove the extension cable for the test Is the image now in focus If not optimize the image by working through the instructions in the How to adjust the screen refresh rate on page 21 section It is normal for blurring to occur due to conduction losses in extension cables You can minimize these losses by using an extension cable with better conduction quality or with a built in booster gt Does the blurring only occur at resolutions lower than the native maximum resolution Read the How to adjust the screen resolution on page 20 section Select the native resolution Pixel errors can be seen 3 One of several pixels is permanently black one or more pixels are permanently white one or more pixels are permanently red green blue or another color e Clean the LCD screen e Cycle power on off e These are pixels that are permanently on or off and is a natural defect that occurs in LCD technology The image has a faulty coloration It has a yell
13. enQ FP73G on the CD and click the Next button This will copy and install the appropriate monitor driver files to your computer Click Finish This will close the wizard and return you to the Monitor Properties window now renamed BenQ FP73G Properties Click Close OK and OK This will close the Display Properties windows You do not need to restart Windows XP as the BenQ LCD monitor drivers will operate immediately with no further action required by you Getting the most from your BenQ monitor How to install on Windows 2000 system Cs You do not need to follow this instruction if you are installing onto a computer which has a Windows XP or later version system In that case see the instructions at How to install on Windows XP systems on page 16 1 Open Display Properties The quickest shortcut to Display Properties is through the Windows desktop Right click the desktop and select Properties from the popup menu Alternatively the Windows menu to Display Properties is located in Control Panel In Windows 2000 version Control Panel is located under the Settings menu item Click Start Settings Control Panel Display The Display Properties window will display 2 Click the Settings tab and the Advanced button The Advanced Display Properties window will display 3 In Windows 2000 click the Monitor tab and the Properties button The Monitor Properties window will display 4 In Windows 2000 click the Driver
14. factory pre set to the PC industry standard white color Reddish applies a warm tint to the image and is factory pre set to the news print standard white color Normal allows video and still photographs to be viewed with natural coloring This is the factory default color User Preset User Preset is provided so you can tailor the image color tint to suit your liking The blend of the Red Green and Blue primary colors can be altered to change the color tint of the image The default start setting is 50 Decreasing one or more of the colors will reduce their respective influence on the color tint of the image e g if you reduce the Blue level the image will gradually take on a yellowish tint If you reduce Green the image will become a magenta tint User Preset Red Green Blue 3 To reset the defaults see Recall sub menu on page 30 for details How to adjust your monitor 27 28 OSD sub menu OSD So TET e H Position V Position OSD Time Press the or P keys to adjust the Horizontal Position of the OSD Press the Exit key to return to previous menu Press the or P keys to adjust the Vertical Position of the OSD Press the Exit key to return to previous menu Press the or P keys to adjust the display time of the OSD Press the Exit key to return to previous menu How to adjust your monitor OSD H Position lt gt SCO OSD V Position lt Ee gt 50 Lan
15. guage sub menu English Francais Deutsch ltaliano Espanol Magyar Language Pycckni Nederlands Polski Cesky Svenska Portuguese SiCG BiH CRO Romana Press the or P keys to select a language to have the OSD display menus in that language Press the Exit key to return to previous menu gt Picture may differ from the Language menu on your monitor depending on the product supplied in your region How to adjust your monitor 29 30 Recall sub menu Recall Color Recall Recall All Press the or P keys to select Color Recall Press the Enter key to recall color settings or press the Exit key to return to previous menu Press the or P keys to select Recall All Press the Enter key to recall position and color settings or press the Exit key to return to previous menu How to adjust your monitor Recall Color Recall YES Recall Recall All YES Miscellaneous sub menu Miscellaneous re Input Select y sharpness Display Information Input Select Press the or P keys to select D sub analog or DVI digital input to activate the new settings Press the Exit key to return to previous menu Sharpness Press the or P keys to adjust the degree of Sharpness Press the Exit key to return to previous menu Display Information Select Display Information to display the current monitor property settings Press the Fxit key to return to previous menu Misc
16. h rate You don t have to choose the highest possible refresh rate on an LCD display because it is not technically possible for an LCD display to flicker The best results are obtained by using the factory modes already set in your computer There is a table with the factory modes in the specification section of this User s Manual N 7 V You can choose 60 70 and 75 Hertz but not 72Hz for the native resolution of 1280x1024 1 Double click the Display icon in Control Panel 2 From the Display Properties window select the Settings tab and click the Advanced button 3 Select the Adapter tab and select an appropriate refresh rate to match one of the applicable factory modes as listed in the specification table 4 Click Change OK then Yes 5 Close the Display Properties window How to adjust the screen refresh rate 21 How to set the picture optimization 22 The easiest way to obtain an optimal display is to use the 7key function Press the key to optimize and adjust the screen settings automatically for you Refer to How to adjust your monitor on page 23 for button locations and functionality If you wish to you can always adjust the screen settings manually using the buttons on the monitor panel To assist you in this endeavour BenQ has provided a screen test image utility which you can use to check for screen color grayscale and line gradient display To make sure the 7key function performs well you have to selec
17. he cables together and reinsert the clip over them to retain the cables neatly in place behind the monitor stand 5 Connect to and turn on the power Plug the other end of the power cord into a power point and turn it on Turn on the monitor by pressing the power button on the front of the monitor Turn on the computer too and follow the instructions in Section 4 Getting the most from your BenQ monitor on page 13 to install the monitor software How to assemble your monitor hardware 9 How to detach the stand base 1 Prepare the monitor and area Turn off the monitor and the power before unplugging the power cable Turn off the computer before unplugging the monitor signal cable Cs Please be careful to prevent damage to the monitor Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls Protect the monitor and screen by clearing a flat open area on your desk and placing a soft item like a towel on the desk for padding before laying the screen face down on a flat clean padded surface 2 Release the locking clip on one side of the stand base whilst pulling the edge of the base away from the stand arm 3 Release the other locking clip to detach the stand base from the monitor stand arm 10 How to assemble your monitor hard
18. hese keys amp switch 1 iKey Adjust vertical position phase horizontal position and pixel clock automatically 2 Exit key Back to previous menu or exit OSD This key is also the hot key for Input Select 3 Left key For Left Decrease adjustment Left key is the hot key for Contrast 4 gt Right key For Right Increase adjustment Right key is the hot key for Brightness 5 Enter key Activate OSD enter sub menu select items and confirm selection 6 Power Turn the power on or off How to adjust your monitor 23 24 Hot key mode The monitor keys perform as hotkeys to provide direct access to particular functions whenever the menu isn t currently displaying on screen Brightness hot key Press the B key to enter the Brightness menu Further press the dor gt keys to adjust the f Brightness degree of screen brightness and press the Fxit key to exit OSD ll tll Contrast hot key Press the 4 key to enter the Contrast menu Further press the qo gt keys to adjust the Contrast degree of screen contrast and press the Exit key to exit OSD a eae Input Select hot key Press the Exit key to enter the Input Select menu Further press the or P keys to indicate the input source and press the Enter key When done press the Exit key to exit OSD Input Select D sub How to adjust your monitor Main menu mode Press the Enter key to display the Main Menu Use the 4
19. ion To attach the rear cover 1 Tilt the rear cover forward and insert the two tabs on the front edge into the recesses of the screw plate No tools are required 2 Position the two tabs on left side of the rear cover to fit into the grooves in the screw plate 3 Push the other two tabs on the right side of the rear cover inward so that they could snap into the aligned grooves There will be a clicking sound as the rear cover is perfectly attached 12 Howto assemble your monitor hardware Getting the most from your BenQ monitor To gain the most benefit from your new BenQ color LCD flat screen monitor you should install the custom BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor CD ROM The circumstances under which you connect and install your BenQ LCD Monitor will determine which process you need to follow to successfully install the BenQ LCD Monitor driver software These circumstances relate to which version of Microsoft Windows you are using and whether you are connecting the monitor and installing the software onto a new computer without existing monitor driver software or whether you are upgrading an existing installation which already has existing monitor driver software with a newer monitor In either case however the very next time you turn on your computer after connecting the monitor to your computer Windows will automatically recognise the new or different hardware and will laun
20. nts Computer Monitors Version 4 0 10 90 TCO 03 TUV Ergonomics TUV GS FCC Class B ISO 13406 2 VCCI CB Report CE C Tick BSMI Fimko GOST CSA CCC Specifications 35 Operating voltage Automatic switched mode power supply 90 264 V 47 63 Hz Dimensions H x W x D 363 8 x 356 5 x 135 mm Weight 3 7 kg 36 Specifications
21. ow blue or pink appearance On the monitor press Enter key and press dor key to move to the Recall icon and press Enter key to enter Recall sub menu Press dor key to select Color Recall and select Yes in Color Recall sub menu then press Enter key to recall to factory settings If the image is still not correct and the OSD also has faulty coloration this means one of the three primary colors is missing in the signal input Now check the signal cable connectors If any pin is bent or broken off please contact your dealer to get necessary support No image can be seen 3 Is the prompt on the display illuminated in green If the LED is illuminated in green and there is a message Out of Range on the screen this means you are using a display mode that this monitor does not support please change the setting to one of the supported mode Please read Supported opearting modes on page 34 section Is the prompt on the display illuminated in orange If the LED is illuminated in orange the power management mode is active Press any button on the computer keyboard or move the mouse If that does not help check the signal cable connectors If any pin is bent or broken off please contact your dealer to get necessary support J Is the prompt on the display not illuminated at all Check the power supply mains socket the external power supply and the mains switch 32 Troubleshooting
22. r software involves selecting an appropriate information file inf on the BenQ LCD Monitor CD ROM for the particular model monitor you have connected and letting Windows install the corresponding driver files from the CD You need only steer it in the right direction Windows has an Upgrade Device Driver Wizard to automate the task and guide you through the file selection and installation process See e How to install on Windows XP system on page 16 e How to install on Windows 2000 system on page 17 Getting the most from your BenQ monitor 15 16 How to install on Windows XP system l 10 11 Open Display Properties The quickest shortcut to Display Properties is through the Windows desktop Right click the desktop and select Properties from the popup menu Alternatively the Windows menu to Display Properties is located in Control Panel In Windows XP version Control Panel is located directly under the main Start menu item The menu options displayed will depend upon which type of view is selected for your system e Under the Classic view click Start Control Panel Display e Under the Category view click Start Control Panel Appearance and Themes Change the screen resolution The Display Properties window will display Click the Settings tab and the Advanced button The Advanced Display Properties window will display Click the Monitor tab and select the Plug and Play Monitor from the list
23. r use in the future when you may need to transport the monitor The fitted foam packing is ideal for protecting the monitor during transport Getting started 5 Getting to know your monitor Front View Back View STL AAATAAAANAAARAABAARADAARAARARD 1 Power AC input jack 2 DVI D Connector 3 D Sub Connector 6 Getting to know your monitor How to assemble your monitor hardware gt If the computer is turned on you must turn it off before continuing Do not plug in or turn on the power to the monitor until instructed to do so 1 Attach the monitor base Cs Please be careful to prevent damage to the monitor Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls Protect the monitor and screen by clearing a flat open area on your desk and placing a soft item like the monitor packaging bag on the desk for padding Lay the screen face down on a flat clean padded surface Whilst holding the monitor firmly against the desk pull the monitor stand arm upwards clear of the monitor Orient and align the stand base socket with the end of the stand arm then push them together until they click and lock into place Gently attempt to pull them back apart to check that they have properly engaged on its stand on a fl
24. t one of the supported modes If the zkey does not work properly and the NON PRESET MODE message is on the OSD it means you are not using one of the supported modes Please set your monitor to use one of the supported modes as listed at the end of this manual l Run the test program auto exe from CD ROM You could also use any other image such as the desktop of your operating system However we recommend that you use auto exe As you run auto exe a test pattern displays Press the ikey button on the monitor Press the Enter key to access the monitor On Screen Display OSD menu If you notice a vertical noise like a curtain effect shimmering of vertical lines press the lt or gt keys to select Geometry and press the Enter key Then press the or P keys to select Pixel Clock and press the Enter key again Then press the or P key to adjust the monitor until the noise disappears If you notice a horizontal noise press the or P keys to select Geometry and press the Enter key Then press the dor keys to select Phase and press the Enter key again Then press the dor keys to adjust the monitor until the noise disappears How to set the picture optimization How to adjust your monitor A look at the control panel es FO 123 4 5 6 There are 6 keys for user s control including 7Key Exit Enter lt and gt key and a power switch The following descriptions are the introduction of t
25. tab and the Update Driver button The Upgrade Device Driver Wizard will display See How to complete the Windows Upgrade Device Driver Wizard on page 18 Getting the most from your BenQ monitor 17 18 How to complete the Windows Upgrade Device Driver Wizard l 10 11 12 oe 14 Load the BenQ LCD Monitor CD ROM which came with your monitor Insert the CD ROM into a CD drive on the computer you attached the monitor to The autorun User s Guide language selection page will display in your web browser You can select a language and view the online version of this manual from the next window You could then print it out for reference if you wish to work off line When youre ready Cancel the browser as it is not required for the Windows Upgrade Device Driver Wizard Launch the Windows Upgrade Device Driver Wizard and click Next Check the option Display a list of known drivers and click Next Click the Have Disk button The Install From Disk window will display Click the Browse button and navigate to the BenQ LCD Monitor CD ROM This is the CD you loaded in step 1 above The CD Drive will have a Windows designated drive letter like D or E or F Select the drive letter corresponding to the drive you put the CD into Double click the folder labelled Driver The contents of the Driver folder will display Click the Open button This will return you to the Install from Disk window
26. the changes and further confirmation to accept the changes Click OK and Yes respectively Getting the most from your BenQ monitor 19 How to adjust the screen resolution 20 Due to the nature of liquid crystal display LCD technology the picture resolution is always fixed The best possible picture for your FP73G is achieved with a resolution of 1280x1024 This is called Native Resolution or maximal resolution that is the clearest picture Lower resolutions are displayed on a full screen through an interpolation circuit Image blurring across pixel boundaries can occur with the interpolated resolution depending upon the image type and its initial resolution Cs To take full advantage of LCD technology you should select the native resolution setting of 1280x1024 1 Open Display Properties and select the Settings tab You can open Display Properties by right clicking on the Windows desktop and selecting Properties from the pop up menu 2 Use the slider in the Screen area section to adjust the screen resolution Select the recommended resolution of 1280x1024 then click Apply N L Q If you select some other resolution be aware that this other resolution is interpolated and may not accurately display the screen image as well as it could do at the native resolution setting 3 Click OK then Yes 4 Close the Display Properties window How to adjust the screen resolution How to adjust the screen refres
27. ware How to use the monitor wall mounting kit The back of your LCD monitor has a VESA standard mount with 100mm pattern allowing the installation of a wall mount bracket Before starting to install a monitor wall mounting kit please read the precautions carefully Precautions e Install your monitor and monitor mounting kit on a wall with flat surface e Ensure that the wall material is stable to support the weight of the monitor e Turn off the monitor and the power before disconnecting the cables from the LCD monitor 1 Remove the monitor base Lay the screen face down on a clean and well padded sur face Detach the monitor base as instructed in How to detach the stand base on page 10 2 Remove the monitor stand Use a a cross pointed screwdriver to release the screws that fixing the monitor stand to the monitor C The use of a magnetic head screwdriver is recommended to avoid of losing the screws Then pull the monitor stand backward away from the monitor N 7 Q In case you intend to use your monitor on the stand in the future please keep the monitor base monitor stand and screws somewhere safe for future use How to assemble your monitor hardware 11 3 Remove the rear cover Pull around the edge of the rear cover and slightly lift it to reveal the screw plate at the back of the monitor 4 Follow the instruction manuals of the wall mount bracket you purchased to complete the installat
Download Pdf Manuals
Related Search