Asrock K8UPGR-1689
Contents
1. EM 7 1CH 312 1 5V AGPI1 AGP 8X SATA USB2 0 DDR2 64 72 bit 184 pin module M1689 PCI1 Chipset PCI2 PANEL 1 PLED PWRBTN ARE GEI itl NM CHA AN USB4 5 USB67 TERE EREE SPEAKERI gp ast 21 20 19 18 17 16 PS2 USB PWR1 Jumper ATX 12V Power Connector ATX12V1 CPU Heatsink Retention Module ATX Power Connector ATXPWR1 CPU Fan Connector CPU FAN1 754 Pin CPU Socket 184 pin DDR DIMM Slots DDR1 2 Primary IDE Connector IDE1 Blue Secondary IDE Connector IDE2 Black AGP Slot 1 5V_AGP1 Bridge Controller Primary Serial ATA Connector SATA1 Secondary Serial ATA Connector SATA2 Clear CMOS Jumper CLRTC1 System Panel Header PANEL1 kk oN Oo SRRHRRSRR Ra 30 5em 12 0 in Chassis Speaker Header SPEAKER 1 USB 2 0 Header USB67 Blue USB 2 0 Header USB4_5 Blue Chassis Fan Connector CHA FAN1 Floppy Connector FLOPPY1 Game Port Header GAME1 Flash Memory PCI Slots PCI1 4 Internal Audio Connector CD1 Black Infrared Module Header IR1 Front Panel Audio Header AUDIO1 JL1 Jumper JR1 Jumper J11 J12 J13 Jumpers Future CPU Port FUTURE_CPU_PORT1 J1 J2 J3 J4 J7 J8 J9 J10 Jumpers 1 4 ASRock SCH UO 1 Parallel Port 8 2 RJ 45 Port 92. Please connect the CPU fan cable to this connector and match the black wire to the ground pin Please connect an ATX power supply to this connector Please note that it is necessary to connect a power supply with ATX 12V plug to this connector Failing to do so will cause power up failure Connect a Game cable to this header if the Game port bracket is installed 2 7 Serial ATA SATA Hard Disks Installation This motherboard supports Serial ATA SATA hard disks and RAID functions This section will guide you to install the SATA hard disks STEP 1 STEP 2 STEP 3 STEP 4 d Install the SATA hard disks into the drive bays of your chassis Connect the SATA power cable to the SATA hard disk Connect one end of the SATA data cable to the motherboard s SATA connector Connect the other end of the SATA data cable to the SATA hard disk 1 If you plan to use RAID 0 RAID 1 or JBOD functions on SATA SATA HDDs must be operated in RAID mode 2 RAID and non RAID mode are options under SATA Operation Mode in BIOS setup Please refer to page 28 for details They need different drivers during actual operation 19 2 8 Making a SATA Driver Diskette For SATA Operation in RAID Mode If you want to install Windows 2000 Windows XP or Windows XP 64 bit OS on your SATA HDDs you will need to make a SATA driver before you start the OS installation STEP 1 STEP 2 STEP 3 STEP 4
3. 3 Side Speaker Gray 10 4 Rear Speaker Black 11 5 Central Bass Orange 12 6 Line In Light Blue 13 7 Front Speaker Lime Microphone Pink USB 2 0 Ports USB01 USB 2 0 Ports USB23 Serial Port COM1 PS 2 Keyboard Port Purple PS 2 Mouse Port Green If you use 2 channel speaker please connect the speaker s plug into Front Speaker Jack See the table below for connection details in accordance with the type of speaker you use TABLE for Audio Output Connection Audio Output Channels Front Speaker Rear Speaker Central Bass Side Speaker nn 7 EEN 4 5 D 3 st SSE 2 Installation K8Upgarde 1689 is an ATX form factor 7 5 in x 12 0 in 19 1 cm x 30 5 cm motherboard Before you install the motherboard study the configuration of your chassis to ensure that the motherboard fits into it Pre installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard settings Before you install or remove any component ensure that the power is switched off or the power cord is detached from the power supply Failure to do so may cause severe damage to the motherboard peripherals and or components 1 Unplug the power cord from the wall socket before touching any component 2 To avoid damaging the motherboard components due to static electricity NEVER place your motherboard directly on the carpet or the like Also remember to use
4. Auto option will disable the legacy USB support 32 3 4 Hardware Health Event Monitoring Screen In this section it allows you to monitor the status of the hardware on your system including the parameters of the CPU temperature motherboard temperature CPU fan speed chassis fan speed and the critical voltage BIOS SETUP UTILITY Main Advanced H W Monitor Security Hardware Health Event Monitoring CPU Temperature 37C 98 F M B Temperature 31 C 87F CPU Fan Speed 2833 RPM Chassis Fan Speed N A Vcore 1 532 V 3 30V 3 129 V 5 00V 4 877 V Select Screen 12 00V 11 741 V Select Item General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 3 5 Boot Screen In this section it will display the available devices on your system for you to config ure the boot settings and the boot priority BIOS SETUP UTILITY Advanced H W Monitor Boot Security Exit Boot Settings Configure Settings during System Boot 1st Boot Device 1st Floppy Device 2nd Boot Device 2nd Floppy Device 3rd Boot Device 3rd Floppy Device gt Hard Disk Drives gt Removable Drives gt CD DVD Drives Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 33 3 5 1 Boot Settings Configuration BIOS SETUP UTILITY Boot Settings Configuration Ta cn ble del De bo
5. Future CPU Port allows you to upgrade your AMD 754 Pin CPU to AMD 939 Pin CPU by installing an add on ASRock 939CPU Board into this future CPU Port on K8Upgrade 1689 motherboard Before you upgrade the 754 Pin CPU to the 939 Pin CPU it is necessary to adjust the jumper settings for those required jumpers on K8Upgrade 1689 motherboard Please refer to the table below for the correct jumper settings This yellow colored Future CPU Port is not an AGP slot Please do 4 NOT insert any AGP card into it CPU Type Jumper Settings Ja J4 754 Pin CPU BEER HRA Ji J2 Default 1 2 J11 1_2 J12 1_2 J13 OJOJOJO O OJOJOJO O J3 J4 OJOJOJO O 01901 010 0 OJOJOJO O OIOJO JO O 939 Pin CPU GEIER 20050 BEN ER BERRE ES FER AREER J7 J8 Jo J10 J1 J2 Using add on ASRock 939CPU Board 2_3 J11 2_3 J12 23 J13 NOTE When adjusting the jumper settings you may use the tool Jumper Cap Remover to help you removing the jumper caps more easily This Jumper Cap Remover is bundled in your motherboard package and please follow the Jumper Cap Remover Instruction to use it properly 13 PCI Slots AGP slot PCI slots are used to install expansion cards that have the 32 bit PCI interface The AGP slot is used to install a graphics card The ASRock AGP slot has a special design of clasp that can securely fasten the inserted graphics card Please do NOT use a 3 3V AGP card on the AGP slot of this motherboa
6. LBA Mode Supported Block Mode 16Sectors PIO Mode 4 Async DMA MultiWord DMA 2 Ultra DMA Ultra DMA 6 S M A R T Supported Select Screen E Se s SC i Sector Transfer Gen Change Option DMA Mode Auto General Help S M A R T Disabled Load Defaults 32Bit Data Transfer Disabled Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 28 TYPE Use this item to configure the type of the IDE device that you specify Configuration options Not Installed Auto CD DVD and ARMD Not Installed Select Not Installed to disable the use of IDE device Auto Select Auto to automatically detect the hard disk drive 4 After selecting the hard disk information into BIOS use a disk utility such as FDISK to partition and format the new IDE hard disk drives This is necessary so that you can write or read data from the hard disk Make sure to set the partition of the Primary IDE hard disk drives to active CD DVD This is used for IDE CD DVD drives ARMD This is used for IDE ARMD ATAPI Removable Media Device such as MO LBA Large Mode Use this item to select the LBA Large mode for a hard disk gt 512 MB under DOS and Windows for Netware and UNIX user select Disabled to disable the LBA Large mode Block Multi Sector Transfer The default value of this item is Auto If this feature is enabled it will enhance hard disk performance by reading or writing more data during each transf
7. Enabled Bank Interleaving Interleaving allows memory accesses to be spread out over banks on the same node or accross nodes decreasing access contention Burst Length Burst length can be set to 8 or 4 beats 64 Bit Dq must use the 4 beats CAS Latency CL Use this item to adjust the means of memory accessing Configuration options Auto 2 0 3 0 and 2 5 TRCD Use this to adjust TRCD values Configuration options Auto 2CLK 3CLK 4CLK 5CLK and 6CLK TRAS Use this to adjust TRAS values Configuration options Auto 5CLK 6CLK 7CLK 8CLK 9CLK 10CLK 11 CLK and 12CLK TRP Use this to adjust TRP values Configuration options Auto 2CLK 3CLK 4CLK 5CLK and 6CLK MA Timing Use this to adjust values for MA timing Configuration options 2T 1T The default value is 2T 25 3 3 2 Chipset Configuration 133 CON Om N 08 2 OM NE F1 AG Advanced ED Enable Disable onboard OnBoard LAN Enabled Audio device AGP Aperture Size 64 MB AGP Data Rate 8X AGP Fast Write Disabled PCI Primary Graphics Adapter HT Speed Auto HT Width Auto Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc OnBoard AC97 Audio Select Auto or Disabled for the onboard AC97 Audio feature OnBoard LAN This allows you to enable or disable the onboard LAN feature AGP Apert
8. ISRock K8Upgrade 1689 User Manual Version 1 0 Published April 2005 Copyright 2005 ASRock ING All rights reserved Copyright Notice No part of this manual may be reproduced transcribed transmitted or translated in any language in any form or by any means except duplication of documentation by the purchaser for backup purpose without written consent of ASRock Inc Products and corporate names appearing in this manual may or may not be regis tered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Disclaimer Specifications and information contained in this manual are furnished for informa tional use only and subject to change without notice and should not be constructed as a commitment by ASRock ASRock assumes no responsibility for any errors or omissions that may appear in this manual With respect to the contents of this manual ASRock does not provide warranty of any kind either expressed or implied including but not limited to the implied warran ties or conditions of merchantability or fitness for a particular purpose In no event shall ASRock its directors officers employees or agents be liable for any indirect special incidental or consequential damages including damages for loss of profits loss of business loss of data interruption of business and the like even if ASRock has been advised of
9. RAID Mode If you want to install Windows 2000 Windows XP or Windows XP 64 bit OS on your SATA HDDs operating in non RAID mode you don t need to make a SATA driver diskette before OS installation 4 Windows 98 SE and Windows ME must be installed by SATA operating in RAID mode and you don t need to make a SATA driver diskette for these two OS before OS installation 20 3 BIOS SETUP UTILITY 3 1 Introduction This section explains how to use the BIOS SETUP UTILITY to configure your system The Flash Memory on the motherboard stores the BIOS SETUP UTILITY You may run the BIOS SETUP UTILITY when you start up the computer Please press lt F2 gt during the Power On Self Test POST to enter the BIOS SETUP UTILITY otherwise POST will continue with its test routines If you wish to enter the BIOS SETUP UTILITY after POST restart the system by pressing lt Ctl gt lt Alt gt lt Delete gt or by pressing the reset button on the system chassis You may also restart by turning the system off and then back on Because the BIOS software is constantly being updated the following BIOS setup screens and descriptions are for reference purpose only and they may not exactly match what you see on your screen 3 1 1 BIOS Menu Bar The top of the screen has a menu bar with the following selections Main To set up the system time date information Advanced To set up the advanced BIOS features H W Monitor To display current hardware
10. drive connected to the Floppy B Disabled system Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 30 3 3 7 Super IO Configuration BIOS SETUP UTILITY Advanced Configure Super IO Chipset Allow BIOS to Enable or Disable Floppy Controller Serial Port Address 3F8 IRQ4 Infrared Port Address Disabled Parallel Port Address 378 Parallel Port Mode ECP EPP EPP Version 1 9 ECP Mode DMA Channel DMA3 Parallel Port IRQ IRQ7 OnBoard Game Port Enabled Select Screen OnBoard MIDI Port Disabled Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc OnBoard Floppy Controller Use this item to enable or disable floppy drive controller Serial Port Address Use this item to set the address for the onboard serial port or disable it Configuration options Disabled 3F8 IRQ4 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 Infrared Port Address Use this item to set the address for the onboard infrared port or disable it Configuration options Disabled 2F8 IRQ3 and 2E8 IRQ3 Parallel Port Address Use this item to set the address for the onboard parallel port or disable it Configuration options Disabled 378 and 278 Parallel Port Mode Use this item to set the operation mode of the parallel port The default value
11. is ECP EPP If this option is set to ECP EPP it will show the EPP version in the following item EPP Version Configuration options Normal Bi Directional and ECP EPP EPP Version Use this item to set the EPP version Configuration options 1 9 and 1 7 ECP Mode DMA Channel Use this item to set the ECP mode DMA channel Configuration options DMAO DMA1 and DMA3 Parallel Port IRQ Use this item to set the IRQ for the parallel port Configuration options IRQ5 and IRQ7 31 OnBoard Game Port Use this item to enable the Game Port or disable it OnBoard MIDI Port Use this itme to select the address for the MIDI Port or disable it Configura tion options Disabled 300 and 330 3 3 8 USB Configuration BIOS SETUP UTILITY Advanced USB Configuration To enable or disable r the onboard USB controllers USB 2 0 Support Enabled Legacy USB Support Disabled Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc USB Controller Use this item to enable or disable the use of USB controller USB 2 0 Support Use this item to enable or disable the USB 2 0 support Legacy USB Support Use this item to enable or disable the support to emulate legacy I O devices such as mouse keyboard etc Or you may select Auto so that the system will start to auto detect if there is no USB device connected
12. status Boot To set up the default system device to locate and load the Operating System Security To set up the security features Exit To exit the current screen or the BIOS SETUP UTILITY Use lt lt gt key or lt gt gt key to choose among the selections on the menu bar and then press lt Enter gt to get into the sub screen 21 3 1 2 Navigation Keys Please check the following table for the function description of each navigation key Navigation Key s Function Description lt gt Moves cursor left or right to select Screens er Moves cursor up or down to select items To change option for the selected items lt Enter gt To bring up the selected screen lt F1 gt To display the General Help Screen lt F9 gt To load optimal default values for all the settings lt F10 gt To save changes and exit the BIOS SETUP UTILITY lt ESC gt To jump to the Exit Screen or exit the current screen 3 2 Main Screen When you enter the BIOS SETUP UTILITY the Main screen will appear and display the system overview BIOS SETUP UTILITY Main Advanced H W Monitor Boot Security Exit System Overview Use Enter TAB or SHIFT TAB to select a field 00 09 System Date Thu 04 26 2005 Use or to configure system Time BIOS Version K8Upgrade 1689 BIOS P1 0 Processor Type AMD Athlon tm 64 Processor 3400 Processor Speed 2200 MHz L1 Cache Size 128KB L2 Cache Size 1024KB Select Screen Select Ite
13. 2 2 Drivers Menu The Drivers Menu shows the available devices drivers including ASRock Ex press GbL PCI Express LAN card driver if the system detects the installed devices Please install the necessary drivers to activate the devices 4 2 3 Utilities Menu The Utilities Menu shows the applications software that the motherboard supports Click on a specific item then follow the installation wizard to install it 4 2 4 Contact Information If you need to contact ASRock or want to know more about ASRock welcome to visit ASRock s website at http www asrock com or you may contact your dealer for further information 37 APPENDIX AMD s Cool n Quiet Technology For power saving sake it is strongly recommended to enable AMD s Cool n Quiet technology under Windows system When using this feature please make sure to install AMD Processor Driver from the Support CD first If you are using Windows 2000 XP operating system please follow the instruction below to enable AMD s Cool n Quiet technology 1 From the Windows 2000 XP operating system click the Start button Select Settings then Control Panel 2 Switch to Classic View for Windows XP only 3 Double click the Display icon in the Control Panel then select the Screen Saver tab 4 Click the Power button The following dialog box appears 5 From the Power schemes combo list box select Minimal Power Management 6 Click
14. Inc Suspend to RAM Use this item to select whether to auto detect or disable the Suspend to RAM feature Select Auto will enable this feature if the OS supports it If you set this item to Disabled the function Repost Video on STR Resume will be hidden Repost Video on STR Resume This feature allows you to repost video on STR resume It is recommended to enable this feature under Microsoft Windows 98 ME Restore on AC Power Loss This allows you to set the power state after an unexpected AC power loss If Power Off is selected the AC power remains off when the power recovers If Power On is selected the AC power resumes and the system starts to boot up when the power recovers Ring In Power On Use this item to enable or disable Ring In signals to turn on the system from the power soft off mode PCI Devices Power On Use this item to enable or disable PCI devices to turn on the system from the power soft off mode PS 2 Keyboard Power On Use this item to enable or disable PS 2 keyboard to turn on the system from the power soft off mode RTC Alarm Power On Use this item to enable or disable RTC Real Time Clock to power on the system 27 3 3 4 IDE Configuration BIOS SETUP UTILITY Advanced DISABLED disables the integrated IDE Controller PRIMARY enables only OnBoard SATA Controller Enabled the Primary IDE SATA Operation Mode SATA Controller SECONDARY enables gt Primary IDE Master Har
15. OK to implement settings If you are using Windows 98SE ME operating system please follow the instruction below to enable AMD s Cool n Quiet technology 1 From the Windows 98SE ME operating system click the Start button Select Settings then Control Panel 2 Double click the Display icon in the Control Panel then select the Screen Saver tab 3 From the Energy saving features of monitor group click the Settings button 4 From the Power Options Properties dialog box select AMD s Cool n Quiet Technology tab 5 Click the Performance combo list box to select desired mode Auto matic mode is the recommended setting 6 Click OK to implement settings 38
16. R266 Max 2GB IDE1 ATA 133 Ultra DMA Mode 6 IDE2 ATA 133 Ultra DMA Mode 6 Supports up to 4 IDE Devices 2 x SATA Connectors Supports up to 2 SATA Devices at 1 5Gb s Data Transfer Rate Supports up to 2 Floppy Disk Drives 7 1 channels AC 97 Audio Speed 802 3u 10 100 Ethernet Supports Wake On LAN CPU Temperature Sensing Motherboard Temperature Sensing CPU Overheat Shutdown to Protect CPU Life ASRock U COP see CAUTION 2 CPU Fan Tachometer Chassis Fan Tachometer Voltage Monitoring 12V 5V 3 3V Vcore Supports CPU upgrade from AMD 754 Pin CPU to AMD 939 Pin CPU see page 13 for details 4 x PCI Slots PCI Specification 2 2 1 x AGP Slot Supports 1 5V 8X 4X AGP Card see CAUTION 3 8 USB 2 0 Ports 4 Ready to Use USB 2 0 Ports on the I O Panel Plus 2 On Board Headers Supporting 4 Extra USB 2 0 Ports see CAUTION 4 1 PS 2 Mouse Port 1 PS 2 Keyboard Port 1 Serial Port COM1 1 Parallel Port ECP EPP Support BIOS OS 4 Ready to Use USB 2 0 Ports 1 RJ 45 Port Audio Jack Side Speaker Rear Speaker Central Bass Line In Front Speaker Microphone see CAUTION 5 AMI Legal BIOS Supports Plug and Play ACPI 1 1 Compliance Wake Up Events SMBIOS 2 3 1 Support CPU Frequency Stepless Control only for advanced users reference see CAUTION 6 Microsoft Windows 98 SE ME 2000 XP compliant CAUTION 1 For power saving sake it is strongly recommended to enable AMD s Cool n Qu
17. SB Configuration DI ORRE NM AUNNIT ND Advanced H W Monitor Boot Security Exit Advanced Settings Options for CPU WARNING Setting wrong values in below sections may cause system to malfunction gt Chipset Configuration gt ACPI Configuration gt IDE Configuration gt PCIPnP Configuration gt Floppy Configuration gt SuperIO Configuration gt USB Configuration Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Setting wrong values in this section may cause the system to malfunction 3 3 1 CPU Configuration BIOS SETUP UTILITY CPU Configuration Select how to set the CPU host frequency Actual Frequency MHz 200 Spread Spectrum Disabled Cool n Quiet Enabled Processor Maximum Multiplier x11 Processor Maximum Voltage 1 550 V Multiplier Voltage Change Auto Memory Clock Auto Flexibility Option Disabled Bank Interleaving Auto Select Screen Burst Length 8 Beats Select Item CAS Latency CL Auto Change Option TRCD Auto General Help TRAS Auto Load Defaults TRP ute Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 23 CPU Host Frequency While entering setup BIOS auto detects the present CPU host frequency of this motherboard The actual CPU host frequency will show in the following item Spread Spectrum This item should always be Disabled
18. STEP 5 Insert the ASRock Support CD into your optical drive to boot your system Do NOT insert any floppy diskette into the floppy drive at this moment During POST at the beginning of system boot up press lt F11 gt key and then a window for boot devices selection appears Please select CD ROM as the boot device When you see the message on the screen Do you want to generate Serial ATA driver diskette YN press lt Y gt Then you will see these messages Please insert a diskette into the floppy drive WARNING Formatting the floppy diskette will lose ALL data in it Start to format and copy files YN Please insert a floppy diskette into the floppy drive and press lt Y gt The system will start to format the floppy diskette and copy SATA drivers into the floppy diskette Once you have the SATA driver diskette ready you may start to install Windows 2000 Windows XP Windows XP 64 bit on your system directly without setting the RAID configuration on your system or you may start to use ALi RAID BIOS Setup Utility to set RAID 0 RAID 1 JBOD configuration before you install the OS Before you start to configure the RAID function you need to check the installation guide in the Support CD for proper configuration Please find the document Guide to SATA Hard Disks Installation and RAID Configuration at the following path in the Support CD RAID_SETUP_GUIDE English PDF 2 9 SATA Operating in non
19. a grounded wrist strap or touch a safety grounded object before you handle components 3 Hold components by the edges and do not touch the ICs 4 Whenever you uninstall any component place it on a grounded anti static pad or in the bag that comes with the component 5 When placing screws into the screw holes to secure the motherboard to the chassis please do not over tighten the screws Doing so may damage the motherboard 10 2 1 Step 1 Step 2 Step 3 j Step 4 2 2 CPU Installation Unlock the socket by lifting the lever up to a 90 angle Position the CPU directly above the socket such that the CPU corner with the golden triangle matches the socket corner with a small triangle Carefully insert the CPU into the socket until it fits in place The CPU fits only in one correct orientation DO NOT force the CPU into the socket to avoid bending of the pins When the CPU is in place press it firmly on the socket while you push down the socket lever to secure the CPU The lever clicks on the side tab to indicate that it is locked B w M Socket Corner vermkever 902 Up SC e S Pa i ER ii 3 Triangle EU Ida AE PR Al STEP 1 STEP 2 STEP 3 STEP 4 Lift Up The Socket Lever Match The CPU Golden Triangle Push Down And Lock To The Socket Corner The Socket Lever Installation of CPU Fan and Heatsink After you install the CPU into this motherboard it is necessary to i
20. d Disk only the Secondary IDE gt Primary IDE Slave Not Detected Controller gt Secondary IDE Master ATAPI CDROM BOTH enables both IDE gt Secondary IDE Slave Not Detected Controllers IDE Configuration gt Select Screen i Select Item Change Option F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit v02 54 C Copyright 1985 2003 American Megatrends Inc OnBoard IDE Controller You may enable either the primary IDE channel or the secondary IDE channel Or you may enable both the primary and the secondary IDE channels by selecting Both Set to Disabled will disable the both Configuration options Disabled Primary Secondary Both OnBoard SATA Controller Use this item to enable or disable the OnBoard SATA Controller feature SATA Operation Mode Use this item to adjust SATA Operation Mode The default value of this option is RAID If you don t want to operate RAID function on SATA HDDs please select non RAID IDE Device Configuration You may set the IDE configuration for the device that you specify We will use the Primary IDE Master as the example in the following instruction which can be applied to the configurations of Primary IDE Slave Sec ondary IDE Master and Secondary IDE Slave as well BIOS SETUP UTILITY Advanced Primary IDE Master Select the type of device connected Device Hard Disk to the system Vendor MAXTOR 6L080J4 Size 80 0 GB
21. er PIO Mode Use this item to set the PIO mode to enhance hard disk performance by optimizing the hard disk timing DMA Mode DMA capability allows the improved transfer speed and data integrity for compatible IDE devices S M A R T Use this item to enable or disable the S M A R T Self Monitoring Analysis and Reporting Technology feature Configuration options Disabled Auto Enabled 32 Bit Data Transfer Use this item to enable 32 bit access to maximize the IDE hard disk data transfer rate 29 3 3 5 PCIPnP Configuration BIOS SETUP UTILITY ET Advanced PCI PnP Settings Value in units of PCI EE clocks for PCI device latency timer register WARNING Setting wrong values in below sections may cause system to malfunction PCI IDE BusMaster Enabled Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Setting wrong values in this section may cause the system to malfunction PCI Latency Timer The default value is 32 It is recommended to keep the default value unless the installed PCI expansion cards specifications require other settings PCI IDE BusMaster Use this item to enable or disable the PCI IDE BusMaster feature 3 3 6 Floppy Configuration In this section you may configure the type of your floppy drive BIOS SETUP UTILITY Advanced Floppy Configuration Select the type of n NO floppy
22. for better system stability Cool n Quiet Use this item to enable or disable AMD s Cool n Quiet technology Processor Maximum Multiplier It will display Processor Maximum Multiplier for reference Processor Maximum Voltage It will display Processor Maximum Voltage for reference Multiplier Voltage Change This item is set to Auto by default If it is set to Manual you may adjust the value of Processor Multiplier and Processor Voltage However it is recom mended to keep the default value for system stability BIOS SETUP UTILITY Advanced CPU Configuration If AUTO FID VID will CPU Host Frequency Auto be left at the rated Actual Frequency MHz 200 frequency voltage If Spread Spectrum Disabled Manual FID VID will Cool n Quiet Enabled be set based on User Processor Maximum Multiplier x11 Selection in Setup Processor Maximum Voltage 1 550 V Processor Multiplier x8 Processor Voltage 1 500V Memory Clock Auto Select Screen Flexibility Option Disabled Select Item Bank Interleaving Auto Change Option Burst Length 8 Beats General Help CAS Latency CL Auto Load Defaults TRCD Auco Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc BIOS SETUP UTILITY Advanced Cool n Quiet Processor Maximum Multiplier Processor Maximum Voltage Multiplier Voltage Change Processor Multiplier Processor Voltage Memory Clock Flexibility Option Bank Interleaving Bu
23. iet technology under Windows system See APPENDIX on page 38 to enable AMD s Cool n Quiet technology While CPU overheat is detected the system will automatically shutdown Before you resume the system please check if the CPU fan on the motherboard functions properly and unplug the power cord then plug it back again To improve heat dissipation remember to spray thermal grease between the CPU and the heatsink when you install the PC system Do NOT use a 3 3V AGP card on the AGP slot of this motherboard It may cause permanent damage Power Management for USB 2 0 works fine under Microsoft Windows XP SP1 2000 SP4 It may not work properly under Microsoft Windows 98 ME For microphone input this motherboard supports both stereo and mono modes For audio output this motherboard supports 2 channel 4 channel 6 channel and 8 channel modes Please check the table on page 9 for proper connection Although this motherboard offers stepless control it is not recommended to perform over clocking Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU 1 3 Motherboard Layout OAN OO P Go MM dk ek ao FON 1 2 3 4 5 19 1cm 7 5 in PS2_USB_PWRI d D TT ER ATXPWRI ATX12V1 140d 7371VvYVvd Socket 754 DDR 1 64 72 bit 184 pin module FSB800 DDR400
24. m Total Memory 512MB Change Field 512MB 166MHz DDR333 Select Field None General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc System Time Hour Minute Second Use this item to specify the system time System Date Day Month Date Year Use this item to specify the system date If ASRock 939CPU Board is installed into the FUTURE CPU PORT on this motherboard you will see the below Main screen when entering the BIOS SETUP UTILITY 22 BIOS SETUP UTILITY Main Advanced H W Monitor Boot Security Exit System Overview Use Enter TAB or SHIFT PAR to 00 09 select a field sn Fri 07 09 2004 Ure aor to configure system Time BIOS Version K8Upgrade 1689 BIOS P1 0 Processor Type AMD Athlon tm 64 Processor 3400 Processor Speed 2200 MHz L1 Cache Size 128KB L2 Cache Size 1024KB Select Screen Select Item Total Memory 512MB Change Field Single Channel Memory Mode Select Field DDR 1 K8_939 512MB 133MHz DDR266 General Help DDR 2 K8_939 None Load Defaults DDR 3 K8_ 939 None Save and Exit DDR 4 K8_939 None Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 3 3 Advanced Screen In this section you may set the configurations for the following items CPU Configuration Chipset Configuration ACPI Configuration IDE Configuration PCIPnP Configuration Floppy Configuration SuperlO Configuration and U
25. nstall a larger heatsink and cooling fan to dissipate heat You also need to spray thermal grease between the CPU and the heatsink to improve heat dissipation Make sure that the CPU and the heatsink are securely fas tened and in good contact with each other Then connect the CPU fan to the CPU FAN connector CPU_FAN1 see Page 8 No 5 For proper installation please kindly refer to the instruction manuals of the CPU fan and the heatsink 11 2 3 Installation of Memory Modules DIMM This motherboard is equipped with two 184 pin DDR Double Data Rate DIMM slots Please make sure to disconnect power supply before adding or removing DIMMs or the system components Step 1 Unlock a DIMM slot by pressing the retaining clips outward Step 2 Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot P i Ip damn re Ne EE E _ break lt notch lt break cs The DIMM only fits in one correct orientation It will cause permanent 4 damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation Step 3 Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated 12 2 4 Expansion Slots Future CPU Port PCI Slots and AGP Slot There are 1 Future CPU Port 4 PCI slots and 1 AGP slot on K8Upgrade 1689 motherboard Future CPU Port Yellow Colored Port
26. ort CD updated the content of this manual will be subject to change without notice In case any modifications of this manual occur the updated version will be available on ASRock website without further notice You may find the latest memory and CPU support lists on ASRock website as Because the motherboard specifications and the BIOS software might be well ASRock website http www asrock com 1 1 Package Contents 1 x ASRock K8Upgrade 1689 Motherboard ATX Form Factor 7 5 in x 12 0 in 19 1 cm x 30 5 cm 1 x ASRock K8Upgrade 1689 Quick Installation Guide 1 x ASRock K8Upgrade 1689 Support CD 1 x Ultra ATA 66 100 133 IDE Ribbon Cable 80 conductor 1 x 3 5 in Floppy Drive Ribbon Cable 1 x Serial ATA SATA Data Cable Optional 1 x Serial ATA SATA HDD Power Cable Optional 1 x ASRock I O Plus Shield 1 x COM Port Bracket 1 2 Specifications Platform CPU Chipsets Memory IDE Serial ATA Floppy Port Audio LAN Hardware Monitor Future CPU Port PCI Slots AGP slot USB 2 0 ASRock 8CH I O ATX Form Factor 7 5 in x 12 0 in 19 1 cm x 30 5 cm 754 Pin Socket Supporting advanced 64 bit AMD Athlon 64 and 32 bit Sempron Processor Supports AMD s Cool n Quiet Technology see CAUTION 1 Bridge ALi M1689 Chipset 1 For 939 Pin CPU FSB 1 GHz 2 0 GT s 2 For 754 Pin CPU FSB 800 MHz 1 6 GT s 2 x DDR DIMM Slots DDR1 and DDR2 Support PC3200 DDR400 PC2700 DDR333 PC2100 DD
27. ot from network feature Bootup Num Lock Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Boot From Network Use this item to enable or disable the Boot From Network feature Boot Up Num Lock If this item is set to On it will automatically activate the Numeric Lock function after boot up 34 3 6 Security Screen In this section you may set or change the supervisor user password for the system For the user password you may also clear it BIOS SETUP UTILITY Advanced H W Monitor Boot Security Security Settings Install or Change the password Supervisor Password Not Installed User Password Not Installed Change User Password Select Screen Select Item Change General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 35 3 7 Exit Screen BIOS SETUP UTILITY Advanced H W Monitro Boot Security Exit Options Exit system setup after saving the changes Discard Changes and Exit Discard Changes F10 key can be used for this operation Load Optimal Defaults Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Save Changes and Exit When you select this option it will pop out the following message Save configuration changes and exit set
28. rd It may cause permanent damage For the voltage infor mation of your AGP card please check with the AGP card vendors Installing an expansion card Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Before installing the expansion card please make sure that the power supply is switched off or the power cord is unplugged Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation Remove the system unit cover if your motherboard is already installed in a chassis Remove the bracket facing the slot that you intend to use Keep the screws for later use Align the card connector with the slot and press firmly until the card is completely seated on the slot Fasten the card to the chassis with screws Replace the system cover 14 2 5 Jumpers Setup The illustration shows how jumpers are setup When the jumper cap is placed on pins the jumper is Short If no jumper cap is placed on pins the jumper is Open The d illustration shows a 3 pin jumper whose pin1 B e Nig and pin2 are Short when jumper cap is ik placed on these 2 pins ahon Bpa Jumper Settin PS2_USB_PWR 1 1_2 23 Short pin2 pin3 to enable Reg OK con 5VSB standby for PS 2 or USB wake up events Note To select 5VSB it requires 2 Amp and higher standby current provided by power supply JL1 JR1 Jumper HODE see p 8 No 27 JL1 JR1 No
29. refer to the instruction of your IDE device vendor for the details Besides to optimize compatibility and performance please connect your hard disk drive to the primary IDE connector IDE1 blue and CD ROM to the secondary IDE connector IDE2 black Serial ATA Connectors These two Serial ATA SATA SATA1 see p 8 No 12 wl ml connectors support SATA data SATA2 see p 8 No 13 cables for internal storage devices The current SATA SATA2 SATA1 interface allows up to 1 5 Gb s data transfer rate Serial ATA SATA Either end of the SATA data cable Data Cable can be connected to the SATA hard disk or the SATA connector on the motherboard 16 Serial ATA SATA Power Cable v A Optional connect to the SATA HDD a power connector 4 connect to the power supply USB 2 0 Header 9 pin USB67 see p 8 No 17 USB 2 0 Header 9 pin USB4_5 ae P 5 P 5 see p 8 No 18 Infrared Module Header 5 pin IR1 see p 8 No 25 Internal Audio Connectors 4 pin CD1 CD R GND CD1 see p 8 No 24 GND CD L Front Panel Audio Header Na 9 pin AUDIO1 BACKOUT R BACKOUT L see p 8 No 26 AUD OUT R MIC POWER MIC 17 Please connect the black end of SATA power cable to the power connector on each drive Then connect the white end of SATA power cable to the power connector of the power supply ASRock 8CH I O accommo dates 4 default USB 2 0 ports If those USB 2 0 ports on
30. rst Length CAS Latency CL TRCD TRAS TRP E 1 EEE ed Select DRAM commands 1 550 V and address timing Manual x8 1 500V Auto Disabled Auto 8 Beats Auto Auto Select Screen Auto Select Item Auto Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 24 Processor Multiplier This item will show when Multiplier Voltage Change is set to Manual otherwise it will be hidden You may set the value from x4 up to x25 but no higher than the value of Processor Maximum Multiplier For example if the value of Processor Maximum Multiplier is x11 the actual value of multiplier will be x11 even if you set this item to a value higher than x11 However for system stability it is not recommended to adjust the value of this item Processor Voltage This item will show when Multiplier Voltage Change is set to Manual otherwise it will be hidden You may set the value from 1 550V down to 0 800V However for safety and system stability it is not recommended to adjust the value of this item Memory Clock This item can be set by the code using Auto You can set one of the standard values as listed 133 MHz DDR266 166 MHz DDR333 200 MHz DDR400 Flexibility Option The default value of this option is Disabled It will allow better tolerance for memory compatibility when it is set to
31. seeeeerterrrrrrrrrrrrnnnne 26 37929 AGPI GOMIGUIAUON asst orerar E E mrs 27 3 3 4 IDE CONIQUrANION EE 28 305 PGI PAP CON IQUEANION S eege 30 3 3 6 Floppy Configuration rrrrnrrrvnnrvrrerrrrrrrrrrrrnrnrnnnnnnnnnnnn 30 3 3 7 Super IO Configuration 31 3 38 USB COnMIgUrAON EE 32 3 4 Hardware Health Event Monitoring Screen 33 3 5 IBOOK SC CON ae 33 3 5 1 Boot Settings Configuration 34 30 Securty STEN r e 35 BU SEN 36 3 4 Software Support ccccceccecseeeeseeceeeeeseeseeseenerseeees 37 4 1 Install Operating System 37 4 2 Support CD Information rrnnnnnonnovnnnvnnnnnnnnnvnvvnnvnnvnnnnnnvenenneeneennn 37 4 2 1 Running Support CID 37 422 Drivers Men sicer e 37 4 2 3 Utilities Menu sree ar a 37 4 2 4 Contact Information ccccsccccccccecceceeeeeeeeeeeeeeeeeeeseeees 37 APPENDIX AMD s Cool n Quiet Technology 38 4 1 Introduction Thank you for purchasing ASRock K8Upgrade 1689 motherboard a reliable motherboard produced under ASRock s consistently stringent quality control It de livers excellent performance with robust design conforming to ASRock s commit ment to quality and endurance In this manual chapter 1 and 2 contain introduction of the motherboard and step by step guide to the hardware installation Chapter 3 and 4 contain the configuration guide to BIOS setup and information of the Supp
32. te If the jumpers JL1 and JR1 are short both the front panel and the rear panel audio connectors can work Clear CMOS Jumper 1 2 2 3 ae mo cnn see p 8 No 14 Default Clear CMOS Note CLRTC1 allows you to clear the data in CMOS The data in CMOS includes system setup information such as system password date time and system setup parameters To clear and reset the system parameters to default setup please turn off the computer and unplug the power cord then use a jumper cap to short pin2 and pin3 on CLRTC1 for 3 seconds Please remember to put the jumper cap back to the default setting short pint and pin2 after clearing the CMOS 15 2 6 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers Do NOT place jumper caps over these headers and connectors Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard Floppy Connector 33 pin FLOPPY1 see p 8 No 20 the red striped side to Pin1 Note Make sure the red striped side of the cable is plugged into Pin1 side of the connector Primary IDE Connector Blue Secondary IDE Connector Black 39 pin IDE1 see p 8 No 8 39 pin IDE2 see p 8 No 9 connect the blue end em rem connect the black end to the motherboard AD to the IDE devices 80 conductor ATA 66 100 133 cable Note If you use only one IDE device on this motherboard please set the IDE device as Master Please
33. the I O panel are not sufficient this USB 2 0 header is available to support 2 additional USB 2 0 ports ASRock 8CH I O accommo dates 4 default USB 2 0 ports If those USB 2 0 ports on the I O panel are not sufficient this USB 2 0 header is available to support 2 additional USB 2 0 ports This header supports an optional wireless transmitting and receiving infrared module These connectors allow you to receive stereo audio input from sound sources such as a CD ROM DVD ROM TV tuner card or MPEG card This is an interface for front panel audio cable that allows convenient connection and control of audio devices System Panel Header oe 9 pin PANEL1 GND see p 8 No 15 DUMMY RESET GND HDLED HDLED Chassis Speaker Header 4 pin SPEAKER 1 SPEAKER DUMMY see p 8 No 16 DUMMY 5V Chassis Fan Connector 3 pin CHA_FAN1 see p 8 No 19 Pe CHA_FAN_ SPEED CPU Fan Connector CPU_FAN_SPEED 3 pin CPU_FAN1 12V GND see p 8 No 5 ATX Power Connector 20 pin ATXPWR1 see p 8 No 4 ATX 12V Power Connector 4 pin ATX12V1 see p 8 No 2 Game Port Header 15 pin GAME 1 see p 8 No 21 18 This header accommodates several system front panel functions Please connect the chassis speaker to this header Please connect a chassis fan cable to this connector and match the black wire to the ground pin
34. the possibility of such damages arising from any defect or error in the manual or product FE This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation ASRock Website http www asrock com Contents BT e Le Dt e TION LEN 5 19 PACKAGES eat Ee EE 5 Age SPECIES Hesse nas er ne 6 129 Motherboard os 9 TA INSROCK SCO en 10 IASTANGN ON ER Seen 10 Pre installation Precautions cccccccccssseeeeeeeeeeeeeeesuaeseeseeeeeeeeeaaaees 10 2 1 VGPU IMStANAN OM san 11 2 2 Installation of CPU Fan and Heatsink eeen 11 2 3 Installation of Memory Modules DIMM ssseeseeeeeeneenneennennnnn 12 2 4 Expansion Slots Future CPU Port PCI and AGP Slots 2 2 13 2 9 JUMpes SQUID Husa etan 15 2 6 Onboard Headers and Connectors rrrrrrrrrnrrrarrrrnrnnnnnnnrnvrnnnn 16 2 7 Serial ATA SATA Hard Disks Installation 19 2 8 Making a SATA Driver Diskette For SATA Operation in RAID Moder 20 2 9 SATA Operating in non RAID Mode rrrnnnnnnnrorrrrnrvrvrvvenernennr 20 BIOS SETUP UTILITY sen 21 del Modul va 21 SA BIOS MEBERG 21 12 NG KOSER 22 32 Man Scree EE 22 3 3 Advanced EE 23 ol GPU e Tute IL DEE 23 3 3 2 Chipset Configuration sssssssssssese
35. up Select OK to save the changes and exit the BIOS SETUP UTILITY Discard Changes and Exit When you select this option it will pop out the following message Dis card changes and exit setup Select OK to exit the BIOS SETUP UTILITY without saving any changes Discard Changes When you select this option it will pop out the following message Dis card changes Select OK to discard all changes Load Optimal Defaults When you select this option it will pop out the following message Load optimal defaults Select OK to load the default values for all the setup configurations 36 4 Software Support 4 1 Install Operating System This motherboard supports various Microsoft Windows operating systems 98 SE ME 2000 XP Because motherboard settings and hardware options vary use the setup procedures in this chapter for general reference only Refer to your OS documentation for more information 4 2 Support CD Information The Support CD that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard features 4 2 1 Running The Support CD To begin using the support CD insert the CD into your CD ROM drive The CD automatically displays the Main Menu if AUTORUN is enabled in your computer If the Main Menu did not appear automatically locate and double click on the file ASSETUP EXE from the BIN folder in the Support CD to display the menus 4
36. ure Size It refers to a section of the PCI memory address range used for graphics memory It is recommended to leave this field at the default value unless the installed AGP card s specifications requires other sizes AGP Data Rate For an AGP 3 0 card you may set AGP Data Rate between 8X or 4X and the default value is 8X For an AGP 2 0 card you may set AGP Data Rate among 4X 2X and 1X and the default value is 4X AGP Fast Write Use this item to enable or disable the feature of AGP fast write protocol support Primary Graphics Adapter This item will switch the PCI Bus scanning order while searching for video card It allows you to select the type of Primary VGA in case of multiple video controllers HT Width You may set the HyperTransport width as 8 BIT 16 BIT or Auto The default value is Auto HT Speed You may set the HyperTransport speed as Auto 200 MHz 400 MHz 600 MHz 800 MHz or 1000 MHz The default value is Auto 26 3 3 3 ACPI Configuration BIOS SETUP UTILITY Advanced ACPI Settings Select auto detect or disable the STR feature Repost Video on STR Resume No Restore on AC Power Loss Power Off Ring In Power On Disabled PCI Devices Power On Disabled PS 2 Keyboard Power On Disabled RTC Alarm Power On Disabled Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends
Download Pdf Manuals
Related Search