Cardo Scala Rider G9x
Contents
1. Pairing a channel will replace any existing paired device on that Channel with the newly paired device Ifyou have purchased the G9x PowerSet both units are factory paired and configured to communicate via Channel A If for any reason you have to pair them again OR if you wish to pair a different unit to make Intercom calls proceed as follows There are two ways to pair Channels A and B OPTION 1 Flash Pairing with other G9 or G9x models See note in 5 1b OPTION 2 Standard Channel A B Pairing with all models 1 Check that all units are in Standby 2 To pair Intercom Channel A press for at least 5 seconds until the RED LED begins flashing rapidly To pair Intercom Channel B press for at least 5 seconds until the BLUE LED begins flashing rapidly 3 Enter Intercom Pairing mode on the second unit following its user manual Both units will now be in Intercom Pairing mode 4 After a few seconds both units will show a solid LED for 2 seconds indicating that they are paired and ready to use 5 If Pairing is not completed within two minutes the units will return to Standby mode 5 2b CALLING INTERCOM CHANNELS A AND B There are two ways to start an intercom call with Channels A and B 10 scala rider G9x G9x PowerSet Channel A Tap Q Q OPTION 1 Voice Connect VOX Speak any word loudly into the microphone When you hear the Voice Command2. scalaricer scala rider O Bluetootti User Guide cardo 2 IL INTRODUCTION iii 3 2 CHARGING THE BATTERY eee eeeooeeeneeeeeooe 4 3 CUSTOMIZATION AND SETTINGS 00000 4 A GETTING STARTED serra 5 4 1 GENERAL FUNCTIONS Jos dan kan os on asakos si spasosebssetisn w 5 A2 STATUS LORT 5 960024506600 ata vo dokt pi ve Da RA YA aosta 6 4 3 AUDIO SOURCES AND PRIORITIES kwa pate ya asa ya kas asti 6 AA VOICE COMMAND w wi done ae eee em api an e ta kan ok eat aa e kaka ja 6 Aa VOICE CONNECT ON leu e desisat enkor enfin l n a ka ti ra ik a ik sea 7 Sc INTERCOM vi ets weds W a rana ia eae 7 5 1148 INTERCOM TOGGLING MODE ss asasen soo pau aiaosdesskese 8 5 2 INTERCOM WITH CHANNELS A AND B sereni zenneana rato 9 5 3 CLICK TO LINK CTL INTERCOM MODE 11 AOU TONAL ateste ie e ki e a r ENERE EE EAE 12 5 RECEIVING INTERCOM CALL konsa asa etat a kai ak ai pi ai a kita ssi 12 3 6 GROUP SIGNAL ciccione ae 12 6 PAIRING AND USING A MOBILE PHONE GPS OR MP3 PLAYER 12 6 1 PAIRING BLUETOOTH CHANNELS 1 AND 2 v saa ente eanessnesss 12 6 2 MAKING AND RECEIVING PHONE CALLS wit easy aaa sato it eens 13 scala rider G9x G9x PowerSet 6 3 LISTENING TO MUSIC VIA A2DP spariranno 13 64 MUSIC SHARING s s an avan asasen aksus se padon edo petardi 13 6 5 LISTENING TO MUSIC VIA THE AUX ccncncrininsrea eee peo tyaer es 14 JFM RADIO s5005beeteecseeenc Goud teat antiaerei 14
3. LE RADIOTUNING aaa a et it Got onesies aa ns 14 7 2 AUTOMATIC RADIO TUNING s satstossastsbsosdevebasetega sewen 15 8 TROUBLESHOOTING save se aou ta aou oui ayi ao ak kra ess tap e a ws 15 9 SUPPORT a a s visa nana ka tie a eske ka TA ak HA ANA 15 10 NOTICES aw aason ea mitan kwa sa ee e anka ea mase 16 IMPORTANT This is version 2 0 of the User Manual Please note that our manual is periodically updated on the Cardo website to include the very latest features and functions Please visit www cardosystems com download manuals to check if the manual you are holding is the most updated version and to download the manual in your preferred language Thank you for choosing the scala rider G9x Bluetooth communication and entertainment system for motorcycle helmets This manual will help you set up configure and operate it Ma Ifyou have purchased the G9x PowerSet your retail box contains two factory paired units Among others the scala rider G9x offers the following key features INTERCOM OPTIONS e Intercom Conference mode between 2 3 or 4 riders at a range of up to 1 6 km e Click to Link Intercom For spontaneous connection with other CTL enabled riders nearby e 1 8 Intercom Toggling with 8 additional buddies MULTIPLE DEVICE CONNECTIVITY e Bluetooth Mobile phones GPS device e Wireless MP3 connectivity via A2DP cable option also provided ENTERTAINMENT OPTIONS e Wireless music strea
4. may damage or impair hearing or lead to hearing loss Permanent hearing loss may occur if Products are used at high volume for prolonged periods of time RF Signals Most electronic equipment is shielded from RF signals However certain electronic equipment may not be shielded against the RF signals emanating from your wireless equipment Pacemakers The Health Industry Manufacturers Association recommends that a minimum separation of about six inches or 16 cm to be maintained between a mobile phone or wireless device and a pacemaker to avoid potential interference with the pacemaker Be sure not to interfere with the functionality of personal medical devices Hearing Aids Some devices may interfere with certain hearing aids In the event of such interference you should consult your hearing aid manufacturer to discuss alternatives Other Medical Devices If you use any other personal medical device consult the manufacturer of your device and or your physician to determine if it is adequately shielded from interference caused by external RF energy Your physician may be able to assist you in obtaining this information LIMITED WARRANTY Subject to the applicable laws and regulations in your jurisdiction your Product is covered by a Two Year Limited product warranty from the date of original purchase Please retain the retail sales receipt and your registration data for proof of purchase Subject to the aforementioned Cardo hereby
5. press and for 2 seconds and follow the spoken instructions Hear Your Buddy In Standby tap and G simultaneously Name Paired Device In Standby press and O for 2 seconds Indication If 1 8 Buddies are within range purple LEDs flash for 2 seconds Enable Disable VOX In Standby press and for 2 seconds For Intercom calls Enabled Blue flash for 2 seconds only e Disabled Red flash for 2 seconds Enable Disable Spoken Status Announcements Press and for 2 seconds scala rider G9x G9x PowerSet 5 rdo 4 2 STATUS LIGHTS None scala rider is OFF 1 BLUE flash every 3 seconds Standby mode No active audio Active mode Call in progress 2 BLUE flashes every 3 seconds music or other audio source is ON 4 3 AUDIO SOURCES AND PRIORITIES If two connected audio sources try to play audio simultaneously your scala rider G9x automatically determines which audio source to play through the speakers based on the priority of the connected devices Higher Priority 1 Mobile Phone or GPS instructions 2 Intercom 3 A2DP Stereo Bluetooth audio 4 FM Radio Built in 5 AUX for corded connection i e Music Players GPS instructions from Smartphone GPS Apps are Lower Priority prioritized like A2DP audio A2DP audio priority can be configured to be higher than Intercom pi See section 3 to adjust settings e Incoming mobile phone calls interrupt ongoing intercom calls
6. 2 Check the unit is in Standby single BLUE flash every 3 seconds 3 To pair Bluetooth Channel 1 press for at least 5 seconds until the RED and BLUE LEDs begin rapidly alternating To pair Bluetooth Channel 2 press for at least 5 seconds until the RED and BLUE LEDs begin rapidly alternating To pair a GPS when LEDs begin rapidly alternating tap 4 Search for Bluetooth devices on your phone GPS MP3 player by following the device s instructions 5 After a few seconds the device will list scala rider G9x Select it 6 If prompted for a PIN or Passkey enter 0000 four zeros 7 The device will confirm that pairing has succeeded and the LED will begin flashing Blue once every 3 seconds 8 If pairing is not completed within 2 minutes the unit will return to Standby mode IMPORTANT e If you have paired 2 different mobile phones directly to your scala rider G9x you will need to set one as default for making calls If your GPS supports it you can pair the second mobile phone directly to the GPS and then pair the GPS to your scala rider G9x and so connect both mobile phones and the GPS to your scala rider G9x NOTES Not all Bluetooth mobile phones can broadcast Bluetooth Stereo music A2DP even if the phone has an MP3 player function Consult your mobile phone s User Manual for more information e Not all Bluetooth GPS devices allow connection to Bluetooth audio devices Consult your G
7. 4 Products opened disassembled or repaired by non authorized parties 5 Defects or damage due to exposure to excessive temperatures adverse weather conditions external impacts or spills of food or liquid 6 All plastic surfaces and all other externally exposed parts that are scratched or damaged after purchase Disclaimer of Warranty The device and its accessories are provided as is and as available without warranty of any kind beyond those assumed in the enclosed manual LIMITATION OF LIABILITY In no event shall Cardo be liable for any incidental special indirect punitive exemplary or consequential damages whether resulting from the use misuse or inability to use this product or from defects in the product or for any damages whatsoever resulting from the use of the product whether based on breach of contract tort including negligence product liability or otherwise even if advised of the possibility of such damages You acknowledge and agree that the limitations set forth above are fundamental elements of this agreement to which you consent and without which the product would not be provided to you absent such limitations Some states do not allow certain exclusions of incidental or consequential damages so the above limitations may not apply to you Cardo retains the exclusive right to repair or replace with a new or newly refurbished replacement Product the device or software or give a refund of the purchase pr
8. be found 14 scala rider G9x G9x PowerSet 7 2 AUTOMATIC RADIO TUNING Find new stations fast and easy by automatically creating a list of 6 temporary radio stations 1 With the radio on press for 5 seconds 2 The radio will search upwards higher frequency from the current station and store the next 6 FM stations it discovers 3 If desired repeat to store the next 6 FM stations FAN DI W These 6 temporary stations cannot be saved and do not replace the FM Presets you may have saved Turning off your scala rider will clear the temporary stations and restore the FM Presets a g cardo If your scala rider stops responding reset it by turning it off and then on again press for 2 seconds 1 In Standby press or for 5 secs until LED flashes RED BLUE 2 Press for 2 seconds until LED flashes 5 times in PURPLE Reset Pairing Deletes all paired devices For additional information J www cardosystems com DK support cardosystems com USA and Canada 1 800 488 0363 International 49 89 450 36819 IMPORTANT MULTINATIONAL COMMERCE COMPANIES AND ONLINE AUCTION WEBSITES ARE NOT AUTHORIZED TO SELL CARDO PRODUCTS AND PURCHASES FROM SUCH SITES ARE AT YOUR OWN RISK TO RECEIVE WARRANTY OR CUSTOMER SERVICE YOU MUST SUBMIT ORIGINAL RECEIPTS FROM AUTHORIZED CARDO DEALERS PRODUCTS THAT WERE IMPORTED FROM NORTH AMERICA MUST BE SERVICED IN THE USA scala ride
9. e Incoming intercom calls will interrupt ongoing A2DP music e Click to Link Intercom and 1 8 calls have the same priority Click to Link requests will not interrupt any type of Intercom call in progress and vice versa 6 scala rider G9x G9x PowerSet 4 4 VOICE COMMAND The scala rider G9x allows you to perform certain actions by simply using your voice Using advanced Voice Recognition you can control the scala rider G9x completely handsfree The default Voice Command language is English Other languages are also available see section 3 to adjust settings Throughout this manual features which are available via Voice Command are marked with the Q icon 1 With no call in progress tap e or speak any word loudly to activate VOX 2 Speak a Voice Command from the table below Current Mode Desired Action Say this 148 Intercom Call lt lt Buddy Name gt gt Intercom call with AorB Call Intercom Standby Standby FM A2DP AUX see Section 5 1 for details FM Radio Voice Command performance may vary based on environmental conditions including driving speed helmet type and ambient noise For improved performance of the Voice Command feature minimize wind impact on the microphone by using the large microphone sponge and closing the visor 4 5 VOICE CONNECT VOX The scala rider G9x offers VOX technology for safe and hands free operation of some key functions You can s
10. represents that this Product is warranted to be free from defects in materials or workmanship proof of purchase and registration required Within the subject period Cardo will at its sole option repair or replace any components that fail in normal use Such repairs or replacements will be made at no charge to the customer for parts or labor provided that the customer shall be responsible for any shipping cost This warranty does not cover failures due to abuse misuse accident or unauthorized alteration or repairs This Product is intended to be used only as a communication and entertainment device and should not be used in any location or jurisdiction where its use is prohibited The warranties and remedies contained herein are exclusive and in lieu of all other warranties express implied or statutory including any liability arising under any warranty of merchantibility or fitness for a particular purpose statutory or otherwise that Cardo specifically disclaims This warranty gives you specific legal rights which may vary from state to state or from jurisdiction to jurisdiction Cardo makes no other warranties express or implied beyond those stated specifically herein This warranty is extended by Cardo solely to the original purchaser and is not assignable or transferable to others Cardo assumes no obligation or liability for additions or modifications to this warranty unless made in writing and signed by an officer of the company Batteri
11. G9x PowerSet 11 ir 5 4 BUSY SIGNAL When attempting to establish an Intercom call with another device that is already busy a busy signal will be heard The scala rider is busy while on a phone call intercom call with Channels A and B 1 8 intercom call or Click to Link call 5 5 RECEIVING INTERCOM CALLS If a paired unit tries calling you via Intercom the call will begin almost instantly 5 6 GROUP SIGNAL Send an instant message to all paired scala rider G9 G9x and cardo SHO 1 units within a range of up to 350 m The recipients will hear a Signal voice announcement To reach a maximum number of riders the message is automatically forwarded to all paired units within the recipient s range In this manner the total range is extended to up to 1 km Send a Group Signal Double tap 9 The transfer of wireless signals is subject to multiple external factors Therefore users may use but should not rely on the Group Signal for emergency purposes 12 scala rider G9x G9x PowerSet To use a Bluetooth device with your scala rider you must first pair them Once paired they will automatically recognize each other whenever they are within range 10m 33ft Your unit has two Bluetooth channels for connection to mobile phones GPS devices and music players with A2DP 6 1 PAIRING BLUETOOTH CHANNELS 1 AND 2 1 Make sure Bluetooth is enabled on your phone GPS MP3 player
12. OM BUDDY Cardo intercom model A and B There are three ways to pair with 1 8 intercom buddies Section Click to Link 1 on 1 spontaneous intercom LI OPTION 1 Pairing via the Cardo Community 5 3 conversations with random riders i th compatibl 41148 SS patible Teer vou ni e na aller Easily find and add your friends to your 1 8 Buddy list via the paired to your scala rider G9x Cardo Community at http community cardosystems com OPTION 2 Flash Pairing with other G9 or G9x models Use Flash Pairing to pair within seconds 1 Remove both units from their Audio Kits and check they are in Standby slow single blue flashing 2 Bump the two units gently against each other and hold them side by side 8 scala rider G9x G9x PowerSet Sie 5 1d CALLING 1 8 INTERCOM BUDDIES There are two ways to start an intercom call with 1 8 buddies Q OPTION 1 Voice Connect VOX Speak any word loudly into the microphone When you hear the Voice Command tone say the name of a 1 8 Intercom Buddy i e John Smith fel CEVAT i ae OPTION 2 Manual Mode 3 If Flash Pairing was successful a purple light aopears for g purple Ig pp SAY THE NAME CHOOSE THE NAME 2 seconds from your Buddy List Press for 2 seconds Hear the names of all pre paired You can also Flash Pair intercom channels A and B by pressing either channel bu
13. PS User Manual for more information After pairing you may need to tap to connect 6 2 MAKING AND RECEIVING PHONE CALLS Answer a call Tap or speak any word loudly to answer by VOX Reject a call Remain silent for 15 seconds or press a for 2 seconds deat iw OSS Voice Dial if supported Tap and follow the prompt from the by mobile phone mobile Double tap Hot Dial Double tap or tap Q and O simultaneously Set default mobile While on a phone call press for 5 seconds Change default mobile In Standby press and for 5 seconds INTERCOM CONFERENCE MODE Add Remove Channel A Tap while on a phone call to from a call Add Remove Channel B Tap Q while on a phone call to from a call This feature is not available during intercom or mobile calls t Before using Hot Dial configure your Hot Dial number via the Cardo Community If you have 2 mobile phones paired directly to your scala rider G9x you will need to set one of them to use as default for outgoing calls cardo Q 6 3 LISTENING TO MUSIC VIA A2DP The scala rider G9x can also receive audio via the enclosed cable from non Bluetooth MP3 Players or audio sources as described in section 6 5 Available only on AVRCP compatible Bluetooth audio sources In standby press for 2 seconds or use Voice Command Pause Stop Press for 2 seconds or use Voice Command Next Track With music ON press for 2 seconds or us
14. a In standby press G for 2 seconds or use Voice Music Sharing does not transmit voice audio and cannot be used as Command an Intercom call Radio Off Press for 2 seconds or use Voice Command a Next Station With radio ON tap or use Voice Command 6 5 LISTENING TO MUSIC VIA THE AUX The USB AUX jack can be used to connect a non Bluetooth audio With Radio ON press and Q simultaneously for source with a 3 5 mm Ye stereo jack using the enclosed cable Default Off 2 seconds 7 1 RADIO TUNING Preset stations can be saved via the Cardo Community the Cardo Smartset App or directly from your scala rider G9x 1 Turn on the Radio 2 Select a Preset number you wish to set Preset 1 6 by tapping O until the desired preset is heard 3 Find an FM station to save using Seek or Scan 1 Check that the scala rider is in Standby Seekup down choose a preset by tapping O 2 Connect the MP3 cable to the Music Player s jack and insert the A Ri Press or for 2 seconds other end of the cable into the USB AUX jack FM station Tap within 20 seconds to save to current preset To listen to music from a cable connected device operate the Music Player using its buttons as usual FF REW PLAY PAUSE Scan and Save With Radio ON press for 5 seconds Automatically To stop search tap scans up fora Tap G within 20 seconds to save to current preset station To continue scan wait for the next station to
15. as successfully passed all interoperability tests that are specified in the Bluetooth specification However interoperability between the device and other B uetooth enabled products is not guaranteed Copyright The contents of this User Guide including all text illustrations and drawings are the exclusive intellectual property of Cardo Systems Inc the Company and are protected by copyright laws They are not in the public domain Any partial or total reproduction translation and or dissemination without the prior written authorization by the Company are strictly prohibited Any rights not expressly granted herein are reserved IMPORTANT SAFETY AND WARRANTY INFORMATION WAIVER AND GENERAL RELEASE WARNING Cardo Systems Inc Cardo or the Company notifies you that your complete and undivided attention is required when using a communication device the Product while riding Failure to avoid potentially hazardous situations could result in accident resulting in serious injury or death Cardo advises you to take all necessary precautions and remain alert to the traffic weather and all road conditions It is best to stop away from traffic prior to activating or deactivating the Product or initiating or receiving any calls Donot perform pairing linking or similar operations while riding All publications are intended to address technical capabilities and should not be construed as encouraging the operation
16. e Voice Command a With music ON press for 2 seconds or use Voice Command With music ON press scans up or 6 scans down for 5 sec The first few seconds of each audio track will be played stop Scan To stop the scan on the current track say any word loudly into the microphone or press for 2 seconds With some phones you may need to repeat this action SWITCHING BETWEEN A2DP AUDIO SOURCES If a Music Player is paired the scala rider G9x will use it as the default A2DP audio source 1 Stop the music playback from the current device 2 Start music playback from the other device 6 4 MUSIC SHARING Music sharing allows rider and passenger to listen to the za Same music within a range of 33 ft 10m e e Music sharing works only with A2DP Bluetooth stereo enabled audio sources In order to share your music with your riding partner your scala rider SENDER needs to be paired to the other unit RECEIVER on CHANNEL A and the RECEIVER must be in Standby mode scala rider G9x G9x PowerSet 13 Your scala rider G9x includes a built in FM radio with a During A2DP music playback press for 2 seconds Press for 2 seconds 6 Preset memory and RDS Radio Data System W RDS allows the radio to automatically retune to the Phone Intercom calls and GPS audio navigation will override music strongest frequency available for the FM station you playback are listening to when the signal becomes too weak an
17. ept any interference including interference that may cause undesired operation of the device FCC RF Radiation Exposure Statement This equipment complies with FCC IC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance The antenna used for this transmitter must not transmit simultaneously with any other antenna or transmitter except in accordance with FCC IC multi transmitter product procedures Industry Canada IC This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device IC RF Radiation Exposure Statement This equipment complies with the RSS 102 exemption from routine RF exposure evaluation for use in an uncontrolled environment 16 scala rider G9x G9x PowerSet European CE Notice Your Cardo product the Product is in conformity with the following essential requirements of Council Directive 1999 5 EC referred to as R amp TTE Directive Articles 3 1a 3 1 b and 3 2 The Product is manufactured in accordance with Annex Il of the above directive Declaration of Conformity DOC The Product is compliant with and adopts the Bluetooth Specification 3 0 Class 1 EDR and h
18. es are warranted only if the battery capacity falls below 50 of rated capacity or if the battery develops leakage Cardo IMPORTANT Do notstore your Product without charging it from time to time for periods in excess of six months as this may cause irreversible damage to the capacity of your battery Your warranty will not cover such events This warranty also becomes void if a any of the seals on the case or battery are broken or Product or battery show signs of tampering b the battery is used in equipment other than the equipment for which it was intended c the Product is used in contravention of its intended purpose d the Product was purchased from online auctions Cardo assumes no responsibility resulting from the use of non Cardo components or products in conjunction with its Products and specifically the use of third party chargers or Bluetooth devices Furthermore Cardo is not responsible for any damage to any part of the Product resulting from the use of ancillary equipment not furnished by Cardo which is attached to or used in connection with the Product Not covered by the warranty 1 Defects or damage resulting from the use of this Product in other than its normal and customary manner 2 Defects or damage from misuse accident or neglect 3 Defects caused by improper operation maintenance installation adjustment or modification of any kind incl long term storage without periodic charging of the battery
19. et VOX to either start an intercom call or activate the Voice Command VOX Activation Speak any word loudly into the microphone Speak any word loudly into the microphone Reject a call Remain silent for about 15 seconds See section 3 to adjust settings High Use this setting if it is difficult to activate VOX Low Use this setting if it is too easy to activate VOX VOX Sensitivity Default Medium VOX can be set to activate the Voice Command default or to start an Intercom Call See section 3 to adjust settings VOX Operation Mode Enable Disable In Standby press and 6 simultaneously for VOX For Intercom 2 seconds Voice Command e Enable Blue flash for 2 seconds only e Disable Red flash for 2 seconds So The scala rider G9x allows full duplex intercom communication at a range of up to 1 6 km subject to terrain and within line of sight Open the antenna for maximum range To chat with someone via Intercom first pair your scala rider G9x to the second unit Pairing is a one time process Once paired the units should automatically recognize each other whenever in range f if you have purchased the scala rider G9x PowerSet the box contains two factory paired units configured to communicate via Channel A Intercom Compatibility Your scala rider G9x is compatible with all scala rider intercom models In addition it is also compatible with the cardo SHO 1 and Schubert s SRC System Intercom range
20. ice at its sole discretion SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY scala rider G9x G9x PowerSet 17 Su Warranty Service To obtain warranty service your Product must be registered Register online at www cardosystems com registration Please present the Product along with your registration number bill of sale receipt at any authorized Service Center or at the store from which you have purchased the Product To obtain warranty service contact Cardo s product support and obtain an RMA tracking number or contact your local Cardo authorized dealer Ship securely with a copy of the original sales receipt which is required as proof of purchase for warranty repairs The RMA tracking number should be written on the outside of the package Send the Product freight charges prepaid to the Cardo address as directed by Cardo Online Auction Purchases Online auction confirmations are not accepted for warranty verification To obtain warranty service an original or copy of the sales receipt from the original retailer is required Cardo will not replace missing components from online auction sites Other manufacturers Cardo is not responsible for and expressly disclaims any responsibility for how Cardo Products are used or misused arising out of use with products services or information of other vendors WAIVER AND GENERAL RELEASE By using the Product you will waive substantial legal rights
21. ider G9x experience and encourage you to write us at support cardosystems com with any questions suggestions or comments you may have Under tough environmental conditions dense forest narrow buildings heavy traffic intercom range will be reduced Once conditions improve the range will increase again scala rider G9x G9x PowerSet 3 4 Channel A MP3 Voice Command Channel B FM scala rider G9x button layout Make sure that the battery is fully charged for at least 4 hours before initial use gt zZ Charging with the wall charger is faster than via a computer USB port RED LED ON Charging RED LED OFF Charging complete iPhones running iOS 5 and up have a Bluetooth headset battery indicator feature to view the battery level of your scala rider on your iPhone s screen The icon appears automatically once you have paired and connected the scala rider to the iPhone For more info consult the status icons section in your iPhone s user guide The scala rider G9x is waterproof and dustproof However when in use the USB silicone cover should be kept tightly closed to prevent moisture from entering the unit scala rider G9x G9x PowerSet Get the most out of your scala rider by changing the settings and customizing your unit according to your own personal preferences There are three ways to change the settings via the Cardo Community on a PC Mac the SmartSet A
22. including the right to sue Please read the following carefully before using the Product By using the Product you are irrevocably releasing indemnifying from any liability loss claim and expense including attorneys fees and holding Cardo harmless for any bodily injuries harm or death as well as losses or damages in goods to any vehicles including your own or to any property or asset that belong to you or to third parties any of which may result from using the Product under any circumstances or conditions and irrespective of jurisdiction 18 scala rider G9x G9x PowerSet 1 You your heirs legal representatives successors or assigns hereby voluntarily and forever release discharge indemnify and hold harmless Cardo from any and all litigation claims debts demands actions and liability which may arise directly or indirectly from using the Product for any distress pain suffering discomfort loss injury death damages to or in respect to any person or property however caused WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE and which may hereafter accrue to you on some future date as a result of said use to the fullest extent permitted by law 2 You fully understand and assume the risks in using the Product including risk of negligent acts or omissions by others All risks for operating the Product are assumed solely by the user of the Product 3 You confirm that you are physically capable to use the Product and that y
23. la rider G9x You can instantly initiate 1 on 1 intercom calls with other riders near you without being paired Think of it as a private channel that you can set up on the go with other riders that you see along the way Click to Link can be disabled effectively blocking any attempt by a third party to send a Click to Link request to you La Start a CTL call request Double tap Q Pairing search lasts up to 10 sec 1 Pair Rider 1 to Passenger 2 using Channel A see 5 2a e End a CTL call Tap Mor 2 Pair Rider 3 to Passenger 4 using Channel A see 5 2a Cancel a CTL call request 3 Pair Passenger 2 to Passenger 4 using Channel B see 5 2a In this configuration the two passengers numbered 2 and 4 are Accepta CTL call When hearing the CTL ringtone Tap Q or each using two Bluetooth connections say any word loudly to answer by VOX Reject a CTL call While hearing the CTL ringtone Calling Remain silent until the ring tone stops or press Q or for 2 seconds 1 Make sure all four units are in Standby 2 Passenger 2 should tap O to call Passenger 4 Enable Disable CTL Via the Settings Menu Cardo Community iN cunt audie is heard on bothunits Enabled by default and the Cardo Smartset App 3 Rider 1 should tap to call Passenger 2 4 Rider 3 should tap Q to call Passenger 4 If other riders are nearby your next Click to Link call may randomly connect to any of them scala rider G9x
24. ming via devices supporting Bluetooth Stereo A2DP and AVRCP profiles e Music Sharing Rider and Passenger can enjoy the same stereo music via A2DP MP3 Players non Bluetooth via cable e Built in FM Radio with 6 station presets and automatic tuning CARDO COMMUNITY e Download software upgrades enhancements and new features Set up your 1 8 Intercom buddies So e Create find and join riding tours e Customize your scala rider G9x settings ADVANCED TECHNOLOGY Voice Command and VOX technology Make Receive mobile calls by voice command Make intercom calls by voice command AGC technology Automatic Gain Control allowing the automatic adjustment of volume according to ambient noise and riding speed You can also control the volume level manually AGC sensitivity levels can be customized to suit your personal preferences VOX technology and Voice Command for safe and hands free operation of key functions VOX sensitivity levels can be customized to suit your personal preferences PLC software Packet Loss Concealment for real time compensation of audio losses in challenging environments Software updates via the Cardo Community on PC Mac Cardo SmartSet App for settings customization on the go Spoken status announcements so that you always know to whom or to what device you are connected Volume Per Mode Volume is set and saved at different levels for each audio source We wish you a great scala r
25. of Cardo s Products in any manner thatis unsafe or prohibited by law Exercise all due caution while using this Product and obey all applicable traffic laws Always ride and use the Product in a safe manner Do not become distracted by the Product while riding on a vehicle When riding always consider road traffic terrain and other conditions to maximize safety Do not operate the Product if it becomes unsafe to do so Insome regions or states the use of mobile communications systems is prohibited or restricted Check all laws and regulations that apply to your region before using the Product and be mindful that compliance with all laws and regulations is the user s responsibility Use the Product in motion only where and inthe manner that such devices are permitted by applicable law The Product should not be used in contravention of local state or federal laws and regulations Please check federal state and local laws and regulations before using your Cardo Product No part of the body should come in contact with the antenna during operation of the equipment Use Product only where safe and avoid usage at gas stations fuel depots or around explosives Use with hearing aids and medical devices only after consulting a physician or specialist Make sure to install and mount the Product in a stable manner HEALTH WARNINGS Hearing Loss Audio devices can cause hearing loss Employ care and avoid exposure to excessive volume levels that
26. ou have no medical conditions or needs that may infringe upon your abilities to do so in a safe manner You further confirm that you will not consume any alcohol that may affect your alertness or any mind altering substance and will not carry use or consume these substances before or during the use of the Product 4 You fully acknowledge our warnings and understand that a risks exist in using the Product while in traffic including but not limited to injury or illness strains fractures partial and or total paralysis death or other ailments that could cause serious disability b these risks may be caused by the negligence of the manufacturers or its agents or any third party involved in the Product c these risks and dangers may arise from foreseeable or unforeseeable causes You hereby assumeall risks and dangers and all responsibility for any losses and or damages whether causedin whole orin part by the negligence or other conduct of others including Cardo 5 By using the Product you confirm that you have read this release of liability and fully understand and accept its terms and conditions www cardosystems com
27. pp or from the Settings Menu on your device Cardo SmartSet Community App Settings Menu Set your Buddy name for 1 8 Intercom Add friends to your Buddy list Create and join tours and invite your friends Set up Intercom to Phone feature Download the latest firmware upgrade Set the 6 FM radio presets Set your Hot Dial number Change A2DP Intercom audio priority Change the Voice Recognition language Disable Spoken Status Announcements Change AGC sensitivity for the speakers Change VOX Operation Mode Change VOX sensitivity for the microphone Disable Click to Link CARDO COMMUNITY WEB PLATFORM Visit http community cardosystems com Minimum Requirements Windows XP Mac OS X 10 5 CARDO SMARTSET APP 4 Download on the App Store ANDROID APP ON P gt Google play SETTINGS MENU The Settings menu is built in to your scala rider and is available in several languages EnterMenu In Standby press and O for 2 seconds ExitMenu Press for 2 seconds Cardo 4 1 GENERAL FUNCTIONS Power ON OFF Press for 2 seconds ON 3 BLUE flashes ascending tone OFF 3 RED flashes decending tone Tap or to adjust and set volume of current audio source Volume Tap and 6 simultaneously Battery level In Standby press for2 seconds indicator Blue LED Full charge e Purple LED Half charge e Red LED Almost empty Enter Settings Menu In Standby
28. r G9x G9x PowerSet 15 Su Federal Communications Commission FCC Statement 15 21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user s authority to operate the equipment 15 105 b This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 ofthe FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must acc
29. tone say Call Intercom to start an intercom call with A and or B subject to who is present VOX Intercom call with only A or B will end automatically after 30 seconds of silence Wi OPTION 2 Manual Mode Use this to start an Intercom call with either Channel B Tap O To end a call tap Q or Q again If you are already in an Intercom call with A or B you can add another rider A or B by tapping the other channel button or another rider can join the intercom call in the same way THREE WAY INTERCOM Use vo Ma go d Rider 2 Rider 3 Rider 1 Pairing Rider 1 is paired to Rider 2 and also to Rider 3 1 Rider 1 pairs to Rider 2 using Channel A see 5 2a 2 Rider 1 pairs to Rider 3 using Channel B see 5 2a Zio IMPORTANT Three Way Conference Mode Considerations IMPORTANT Four Way Conference Mode Considerations During a 4 Way Intercom call the two passengers who maintain two active connections will not be able to receive mobile phone calls or GPS instructions as long as the conference call is in progress During a 3 Way Intercom Conference call with 2 other participants Rider 1 will not be able to receive mobile phone calls or GPS navigation instructions as long as the call is in progress 5 3 CLICK TO LINK CTL INTERCOM MODE Click to Link is a spontaneous social feature of your sca
30. tton or before bumping the units together 1 8 buddies When you hear the name of OPTION 3 Standard 1 8 Pairing Tap and say the name of the Buddy you wish to call with cardo SHO 1 G9 and G9x models the 1 8 Buddy tap or say any word loudly 1 In Standby press for 5 seconds to enter pairing mode into the microphone To cancel Buddy List playback 2 Repeat on the second unit Press for 2 seconds 3 If pairing was successful a purple light appears for 2 seconds If your scala rider G9x already has a full list of 8 paired 1 8 Intercom Buddies pairing another buddy will replace the buddy that you have not spoken to for the longest time Ifa 1 8 intercom buddy is not in range or moves out of range you have the option to set up the IC to Phone feature via the Cardo Community to remain in contact by diverting Intercom calls to your mobile phones 5 1c PAIRED DEVICE INDICATION You can see which units within a range of 20m are your 1 8 5 2 INTERCOM WITH CHANNELS A AND B Intercom Buddies Start multi party conversations using Intercom Channels A and B This mode is suitable for 2 3 or 4 way calls In Standby press and O for 2 seconds If 1 8 Buddies are within range the LEDs on both units will turn PURPLE for 2 seconds Paired Device Indication scala rider G9x G9x PowerSet 9 ra 5 2a PAIRING INTERCOM CHANNELS A AND B
31. with other models is limited to the distance of the device with the shorter range For more info please visit www cardosystems com G9xcompatibility scala rider G9x G9x PowerSet 7 a Cardo Intercom communication is possible using one of the three 5 1 1 8 INTERCOM TOGGLING MODE Intercom modes Pair with up to 8 other devices 1 8 Buddies and connect with them one at a time by saying their name 5 1a CONFIGURING YOUR BUDDY NAME Before using 1 8 Intercom you should assign your device a Buddy Name so that other 1 8 participants can call you by this name If you change your Buddy Name you must pair again with your w 1 8 Buddies for their device to receive your new Buddy Name 4 Ses Visit the Cardo Community to configue your Buddy Name see ati Section 3 Until you configure a Buddy Name your unit will be known by its generic 1 8 Buddy name scala rider G9x Hear Your In Standby tap QO and O simultaneously You will hear 1 8 Intercom Toggling 2 way Intercom conversations Buddy Name the Buddy name of your scala rider G9x through the within a group of up to eight other speakers between scala rider 148 Buddies Play Paired Sa n cardo Buddy List In Standby press for 2 seconds HO 1 only Section Intercom via Channels Intercom Conferencing 2 way n Pe 5 2 A and B with any 3 way and 4 way using Channels 5 1b PAIRING WITH A 1 8 INTERC
Download Pdf Manuals
Related Search