Home

Tenda 4G630 router

1. Ve To scan and connect to a remote wireless device see Universal Repeater Mode in 4 Quick Internet Setup amp Wireless Security Setup 2 To connect the device wirelessly see 2 Join Your Wireless Network 2 Configure Your PC lf your computer is set to a static or fixed IP address This is uncommon change it to Obtain an IP address automatically and Obtain DNS server address automatically from the device See 1 Configure Your PC GR Quick Setup Tenda 3 Web Login Launch a Web browser say IE Inter Mt Explorer In the address bar input the device s LAN IP address 192 168 0 1 by default and press Enter 3 Enter the login password admin by default and click Login Mobile WIFI User Name admin Login Cancel The Status screen appears Click Wizard to enter the setup wizard interface is fi Quick Setup Tenda 3G 4G Traffic Statistics WAN Status Internet Connection Status WAN IP Subnet Mask Gateway Primary DNS Server Secondary DNS Server Internet Connection Type Connect LAN Status IP Address Subnet Mask DHCP Server Wireless Status Wireless Radio SSID Wizard ie Home 3G 4G USB modem not attached 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3G 4G Disconnect 192 168 0 1 255 255 255 0 Enabled Enabled Tenda_38DDC9 Wireless Router Mode Ge 3G 4G Router Mode Universal Repeater Mode MV Auto
2. os B Features y Configurations Tenda you to reset the device Time amp Date Restore to Factory Default Firmware Upgrade To restore factory defaults click the Restore to Factory Default button below Backup amp Restore Restore to Factory Default Restore to Factory Default Change Password Logs Reboot The factory default settings are listed below e IP Address 192 168 0 1 Subnet Mask Enter 255 255 255 0 Password admin 5 5 Change Password Help The device will be reset to factory defaults if this option is enabled Default Password admin Default IP 192 168 0 1 Default Subnet Mask 255 255 255 0 Click Tools gt Change Password to enter the configuration screen It is strongly recommended that you change the factory default login password Otherwise anyone in your network can access this utility to change your settings Zoe The default login password is admin A valid password must only include letters numbers or underscore we A Features A Configurations Tenda Time amp Date Firmware Upgrade Backup amp Restore Restore to Factory Default Change Password Logs Reboot Change Password Note Password can only include letters numbers or underscore New Password Confirm New Password Cancel Configuration Procedures 5 6 Logs New Password Input a new password Click Save to save your settings Old Password
3. Wy Documents Open Explore Search For Computers Map Network Drive Disconnect Network Drive Create Shortcut Delete Rename __ Propertigs Step 2 Right click Wireless Network Connection and select View Available Wireless Networks as B Appendix Tenda Tere Disable Yiew Available Wireless Networks Status Repair C tp e Bridge Connections Create Shortcut Delete Rename Properties Step 3 Double click the name of the wireless network SSID you wish to join and then follow onscreen instructions Wireless Network Connection Network Tasks Choose a wireless network G Refresh network list Click an tem in the list below bo connect to a wireless network in range or to get more information Tenda _5G_4BC730 2 Set up a wireless network A p LO For a home or small office Unsecured wireless network Related Tasks D Tenda_5G_ 000058 Unsecured wireless network Test yank w85ap 5 0 Raas E Security enabled wireless network WPA FZ VI Learn about wireless networking i Change the order of preferred networks settings ee Change advanced a k E Security enabled wireless network WP AZ Tenda_OFFO D DG Security enabled wireless network pw PA To connect to this network click Connect You might need to enter additional information When Connected appears next to the selected wireless network SSID you have successfully connected to it Ei
4. Deele Rename Properties IN Appendix Tenda Step 2 Right click Local Area Connection and select Properties Disable Status Repair Bridge Connections Create Shortcut Delete Step 3 Scroll down to find and double click Internet Protocol TCP IP Local Area Connection Properties sde Connect using E9 Marvell Yukon 88E8057 PCI E Gigabi Configure This connection uses the following tems Client for Microsoft Networks File and Printer Sharing for Microsoft Networks QoS Packet Scheduler wi Internet Protocol TCPAIF ee a Descnption Transmission Control Protocal Internet Protocol The default wide area network protocol that provides communication across diverse interconnected networks V Show icon in notification area when connected V Notify me when this connection has limited or no connectivity Ay Appendix Tenda Step 4 Select Obtain an IP address automatically and Obtain DNS server address automatically and click OK Le Internet Protocol TCP IP Properties General Altemate Configuration You can get IP settings assigned automatically if your network supports this capability Othervase you need to ask your network administrator for the appropriate IP settings Ce Obtain an IP address automatically O Use the following IP address r rie Obtain DNS server address automatically Use the following DNS server addresses Step 5 Click O
5. Enter the current login password Help Device s default password is admin Itis advisable to change it for better security Otherwise anyone in your network may access this utility to view or change your settings Old Password Enter the old password If you use the device for the first time the password is admin by default Note Password cannot be retrieved once lost If you already changed the password and unfortunately forget restore the device to factory defaults New Password Input a new password Password must only include 3 12 characters except space Confirm New Password Re enter the new password for confirmation Confirm New Password Re enter the new password for confirmation Click Tools gt Logs to enter the configuration screen Here you can view the history of the device s actions upon system startup Time amp Date Firmware Upgrade Backup amp Restore Restore to Factory Default Change Password System Logs Refresh clear Type of logs to display ayy Index Log Content 22 2013 12 16 18 59 05 system wan up 21 2013 12 16 18 59 02 system wan down Page 321 E Help The Logs option allows you to view all events that occur upon system startup and check whether there are attacks present in your network Note Logs will be replaced automatically once it reaches 20 pages namely 200 entries e B Features A Configurations Tenda 5 7 Reboot
6. He always downloads a large volume of data from the Internet which sharply frustrates your Internet surfing experience you can use this feature to set limits for the volume of Internet traffic he can get For example you can equally split the bandwidth so your neighbor can only use up to 2M Internet traffic and you can smoothly enjoy 2M Configuration Procedures Bandwidth Control Check the Enable box to enable the feature IP Address Enter the last number of the IP address Here in this example enter 125 in both boxes Upload Limit Set a limit to regulate the uplink bandwidth of PC s on the LAN Here in this example enter 32 in both boxes Download Limit Set a limit to regulate the downlink bandwidth of PC s on the LAN Here in this example enter 256 in both boxes Enable Check to enable the current rule Add to List Click to add the current rule to the rule list Click Save to save your settings sa B Features A Configurations Tenda Advanced DDNS Settings Bandwidth Control Help Bandwidth Control Bandwidth Control Enable Use this section to manage bandwidth allocation to IP Address 192 168 0 125 devices on your LAN Upload Download Limit Set a Upload Limit 32 KB s Max Traffic limit to regulate upload download bandwidth Download Limit 5 KB s Max Traffic of PCs on the LAN Remote Web Management Upload Download Limit Seta Enable upload download limit on specified PC s DMZ Host U
7. SSID and Key and then click Next we BR Quick Setup Tenda Wizard Wizard LA Home Help 3G 4G Router Mode In this mode the router acquires SSID Tenda_38DDC9 Internet access through an activated 3G 4G USB modem which is attached to its USB port Wired WAN access is disabled Wireless Router Mode In this mode the router acquires Internet access through a wired WAN port 3G 4G access is disabled Universal Repeater Also known as Client plus AP Mode In this mode the router acquires Internet access from a remote wireless device and provides access to clients in the meantime Channel 4 Key 12345678 Security Mode Tenda optimizes wireless security Default AES under WPA2 PSK will effectively protect your network against unauthorized accesses If this field is left blank your wireless network is not secured Previous 4 Click Finish and wait for the device to restart Wizard Wizard Help we Home 3G 4G Router Mode In this mode the router will try 3G 4G access only WAN access is disabled Wireless Router Mode In this mode the router will try WAN access only 3G 4G access is disabled Configurations complete Previous Finish Zoe In Universal Repeater Mode your wireless network must operate on the same channel as the remote AP Auto switch System Mode amp Priority Auto switch System Mode If unchecked system will not switch between the 3G 4G Router Mode and Wireless Ro
8. to your local hard drive Click the Browse button to locate and select a configuration file that is saved previously to your local hard drive And then click the Restore button to reset your device to previous settings Select the configuration file that is saved previously to your local hard drive and click Open os B Features A Configurations Tenda Organize s New folder E Wm System Folder Ke Favorites ME Desktop 5 Wireless Utility dp Downloads oe lian l a 2356 KB El Recent Places WSI11E Poe File folder Ee Documents WS11E_V1 0 0 4 Setup Test a Music File folder El Pictures Videns _ RouterCftm ctg CHG File 6 56 KB ee s US 46300_EN_root_ulmage em Win en C File Ca win xp D m 2 64 MB ihe Computer File name PRouterCfm Betz All Files Click the Restore button to reset your device to previous settings 5 4 Restore to Factory Default Click Tools gt Restore to Factory Default to enter the configuration screen Here you can reset the device to factory default settings ANote If you enable this option the device will be restored to factory default values You will have to reconfigure Internet connection settings and wireless settings Do not restore factory default settings unless the following happens v You need to join a different network or unfortunately forget the login password v You cannot access the Internet and your ISP or our technical support asks
9. 2D SE FRG Gel SRNR Sea Ss PRE MAWES Saat ZTE RE RD Sa ASR ED RS HRERMAERRBS ABE SSES IN Se E VEGA dp OS SRB R SRR NASA KE EREFR CR me EE EE SE SPERBRASREA HS Bix ET erg Tenda
10. Backup amp Restore Change Password Click OK on the appearing window Message from webpage 2 Please select a directory before exporting settings Click Save on the File Download window al Do you want to save this file or find a program online to open it gt Name BackUp cfg al Type Unknown File Type 12 8KB From 192 168 0 1 While files from the Internet can be useful some files can potentially harm your computer If you do nottrust the source do notfind a program to open this file or save this file What s the risk Select a local hard drive to save the file and click Save o B Features y Configurations Tenda Organize New folder A i k Favorites RE Desktop Ja Downloads Recent Places Libraries _ Documents d Music Pictures amp Videos kb Computer a k File name RMG nae Save as type CFG File ia Hide Folders To restore configurations Click Browse Time amp Date Backup amp Restore Libraries System Folder luckyme System Folder Computer System Folder Network System Folder W311E Firmware Upgrade Note Use this section to backup current settings or restore previous settings Backup amp Restore Restore to Factory Default Change Password Logs Reboot Save Settings to Local Backup Load Settings From Local Restore Help Click Backup to save a copy of the device s current settings
11. Features A Configurations Tenda devices if any connected to the device Wireless Basic Wireless Connection Status Help Security This section displays info of connected wireless clients This section displays info of Currently Connected Clients Refresh connected wireless clients MAC Wireless MAC address of a current host Access Control Connection Status NO MAC address Bandwidth 1 70 72 30 30 4B D7 58 0 Mbps Zoe The Bandwidth here refers to the channel bandwidth instead of wireless connection rate You can know whether there are unauthorized accesses to your wireless network by viewing this connection status list 4s Bi Features A Configurations Tenda 4 Advanced Applications This section includes the following Toremotely access the device via a domain name or access a server ona LAN PC see 4 1 DDNS Settings To let an Internet user access your LAN PC without any restriction see 4 2 DMZ Host To automatically map the ports between WAN and LAN see 4 3 UPNP To enable the remote Web management feature see 4 4 Remote Web Management To regulate bandwidth see 4 5 Bandwidth Control Available only in 4G600 To restrict your LAN PCs to access certain services on the Internet via their IP addresses see 4 6 Client Filter Available only in 4G600 4 1 DDNS Settings Dynamic DNS or DDNS is a term used for the updating in real time of Internet Domain Name System DNS na
12. device s PIN code Start PIN If you enter the client s PIN code on the router clicking this button starts the PIN connection Operation Instructions PBC If you press the hardware WPS button on the device for 1 second the WPS LED will blink for about 2 minutes indicating that the PBC encryption method is successfully enabled During this time an authentication routine can be performed between your device and a WPS PBC capable wireless client Simply enable the WPS PBC on the client wireless device If it passes the authentication the wireless client device connects to your device and the WPS LED turns off Repeat the steps above if you want to add more wireless client devices to your device PIN To use this option you must know the PIN code from the wireless client and enter it in the corresponding field on your device while using the same PIN code on the client side for this connection A Note To use the WPS encryption the wireless client device must also be WPS capable The WPS becomes unavailable if you select any of the following option Open Shared WPA2 PSK plus TKIP and Mixed WPA WPA2 PSK plus TKIP 3 3 Access Control Specify a list of devices to Allow or Deny a connection to your wireless network via the devices MAC Addresses Click Wireless gt Access Control to enter the configuration screen Three options are available Disable Deny and Allow A If you want to allow all wireless clients to jo
13. in the order listed below AL Tenda_home Automatic i Appendix Tenda 5 Safety and Emission Statement CE CE Mark Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures This device complies with EU 1999 5 EC NOTE 1 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment 2 To avoid unnecessary radiation interference it is recommended to use a shielded RJ 45 cable Ve FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may Cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a
14. new devices to an existing network without entering long passphrases or configuring complicated settings Simply enter a PIN code or press the hardware WPS button and a secure wireless connection is established Wireless Basic Wireless Security Help Shared or Mixed WEP from the Security Mode Disable corresponding drop down list ASCII Enter 5 or 13 ASCII WPS Settings characters Hex Enter 10 or 16 Hex characters Access Control Connection Status WPS Disable CG Enable WPA WPA2 You can select either personal or mixed only Device Pin 69790980 ensure that either one you selectis supported on your WPS Type PBC PIN wireless clients Important If you are an Start PIN Reset OOB advanced user and have configured security mode before you can select any mode you like only to assure that the one you choose is also supported by your wireless clients if you are new to networking and have never configured this parameter before we suggest that you select WPA PSK or WPA2 PSK Cancel J Knowledge Center L WPS Select Enable Disable to enable disable the WPS encryption WPS Type Select PBC Push Button Configuration or PIN Reset OOB If clicked the WPS LED will turn off and the security function will be disabled automatically The WPS server on the router enters idle mode and will not respond to any client s WPS connection request am Features A Configurations Tenda Device PIN Displays the
15. particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna i Appendix Tenda Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This transmitter must not be co located or operating in conjunction with any other antenna or transmitter The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body NOTE 1 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment 2 To avoid unnecessary radiation interference it is recommended to use a shielded RJ 45 cable NCC Notice MH Twat
16. require the client DHCP Client List PC s MAC address for Internet connection authentication In this case simply enter the correct MAC address or click the Clone MAC button and then save your settings Clone MAC Click to copy your PC s MAC address to the device WAN Speed Restore Default MAC Clone MAC DNS Settings LA Knowledge Center Restore Default MAC Reset the device s WAN MAC address to factory default Clone MAC Clicking this button copies the MAC address of the computer that you are currently using to the router Note that you have to use the computer whose MAC address is allowed by your ISP Also you can manually enter the MAC address that you want to use To restore default MAC address Click Restore Default MAC Click Save to save your settings To copy the MAC address of the computer that you are currently using to the device Click Clone MAC Click Save to save your settings To manually enter the MAC address allowed by your ISP Enter the MAC address allowed by your ISP Click Save to save your settings as i Features A Configurations Tenda 2 6 DHCP Server DHCP Dynamic Host Configuration Protocol assigns an IP address to each device on the LAN private network When you enable the DHCP Server the DHCP Server will automatically allocate an unused IP address from the IP address pool specified in this screen to the requesting device as long as the device i
17. seconds to enable WPS quick encryption WAN Internet port for cabling the device to the Internet side LAN1 2 3 Local LAN Ethernet ports for cabling the device to I Product Overview Tenda local computers switches etc POWER Power port for connecting the device to a power outlet 2 4 Label a Madein china Tenda www tendacn com 3G 4G Wireless N300 Router Model 4G630 IP Address 192 168 0 1 User Name admin Password admin Power 12V 1A FCC ID S Ser e UNa 1 Product Model 2 Default Login IP address This IP address is to be used to access the device s settings through a Web browser 3 4 Default login user name password This information is to be used for web access authentication 5 Device s physical address I Product Overview Tenda Il Quick Setup 1 Hardware Install You can either connect to the device wirelessly or using Ethernet cables Select an install method according to your network environment A If you access the Internet via a 3G 4G USB modem see 3G 4G Router Mode B If you access the Internet by connecting the device to the Ethernet cable from the incoming Internet side see Wireless Router Mode C If you acquire Internet access from a remote AP on an existing network see Universal Repeater Mode ANote DO NOT expose the device to heat sources Disconnect the device from power supply in thunderstorm weather 8 Keep the device
18. the device Configuration Procedures Country Select your country Service Provider ISP Select your 3G 4G service provider and ISP APN Access point Name Consult your ISP if you are not clear SG Dial Number Common numbers are 99 777 and 99 1 Consult your ISP if you are not clear User Name Password Enter the user name and password for your 3G 4G Internet service Click Save in ok Knowledge Center Connect Automatically Connect automatically to the Internet after rebooting the system or connection failure fos A Features A Configurations Tenda Connect Manually Require the user to manually connect to the Internet before each session Connect On Demand Re establish connection to the Internet only when there is data transmitting Connect During Specified Time Period Connect automatically to the Internet during a specified time length Wireless Router Mode The Wireless Router Mode includes the following Internet connection types e DHCP PPPoE Static IP L2Tp PPTP A Select PPPoE if your ISP uses a PPPoE connection and gives you a PPPoE user name and a PPPoE password B Select Static IP if your ISP provides you with fixed or static IP address settings special deployment by ISP this is rare C Select DHCP Dynamic IP if your ISP does not provide you with any ISP login account or IP information D Select L2TP Layer 2 Tunneling Protocol if your ISP us
19. to save your settings Zoe Ifthe IP address you have reserved for your PC is currently used by another client then you will not be able to obtain a new IP address from the device s DHCP server instead you must manually specify a different IP address for your PC to access the Internet For PCs that have already obtained IP addresses you may need to perform as B Features A Configurations Tenda the Repair action to activate the configured static IP addresses ao Bi Features A Configurations Tenda 3 Wireless Settings To configure wireless network name channel and other basic wireless settings see 3 1 Basic To secure your wireless network see 3 2 Security To restrict access to your wireless network see 3 3 Access Control To see who are connecting to your wireless network see 3 4 Connection Status 3 1 Basic Here you can configure the basic wireless settings of the device Wireless Wireless Basic Help Security Wireless Enable GG Enable This section allows you to config basic wireless settings SSID Tenda_38DDC9 Itis advisable that you only config the SSID and channel 802 11 Mode 41b g n mixed mode settings and leave other items unchanged BSSID C8 3A 35 38 DD C9 SSID This is the public name of your wireless network SSID Broadcast Enable Disable Broadcast SSID Wireless Access Control Connection Status clients find your wireless Channel 2462MHz Channel 11 network
20. to update the Backup amp Restore Restore to Factory Default Change Password device The device restarts Logs automatically when update completes Reboot Select the firmware file you want to use and click Open Click Upgrade Click OK onthe appearing screen and wait for it to complete When upgrade is completed check the Current System Version field It should display the firmware you load 5 3 Backup amp Restore Once you have configured the device the way you want it you can save these settings to a configuration file on your local hard drive that can later be imported to your device in case that the device is restored to factory default settings Click Tools gt Backup amp Restore to enter the configuration screen Zoe It is advisable to include the file name suffix of cfg to avoid problems when renaming the file name To backup configurations Click Backup e B Features A Configurations Tenda Time amp Date Backup amp Restore Help Firmware Upgrade Note Use this section to backup current settings or restore previous settings Click Backup to save a copy Save Settings to Local Backup of the device s current settings 7 to your local hard drive Click Restore to Factory Default a Restore ee RSR and select a configuration file that is saved previously to your local hard drive And then click Logs the Restore button to reset your device to previous Reboot settings
21. with a PPPoE username and a PPPoE password Simply enter them in corresponding fields 30 B Features A Configurations Tenda PPTP Server Address Enter the PPTP IP address provided by your ISP User Name Enter your PPTP user name 4 Password Enter your PPTP password Address Mode Select Dynamic if you don t get any IP information from your ISP otherwise select Static Consult your ISP if you are not clear IP Address Enter the IP address provided by your ISP Consult your local ISP if you are not clear Subnet Mask Enter the subnet mask Gateway Enter the gateway provided by your ISP Consult your local ISP if you are not clear Click Save to save your settings WAN MTU Setup The MTU maximum transmission unit is the largest data packet a network device transmits The normal MTU value for most Ethernet networks is 1500 bytes or 1492 bytes for PPPoE connections For some ISPs you might need to change the MTU This is rarely required and should not be done unless you are Sure it is necessary for your ISP connection When one network device communicates across the Internet with another the data packets travel through many devices along the way If a device in the data path has a smaller MTU value than the other devices the data packets have to be fragmented to accommodate the device with the smallest MTU value The best MTU value is often just the factory default value In some situations chan
22. your ISP Consult your local ISP if you are not clear Click Save to save your settings PPTP PPTP Point To Point Tunneling Protocol is a network protocol that enables the secure transfer of data from a remote client to a private enterprise server by creating a VPN across ITCP IP based data Enter your ISP provided information to establish a connection MPPE is an encryption technology developed by Microsoft to encrypt point to point links LAN Settings WAN Settings WAN Settings Internet Connection Type gt WAN Speed p PPTP Server Address IP Address DNS Settings User Name MAC Clone Password DHCP Server Address Mode Static DHCP Client List IP Address Subnet Mask Gateway MPPE CO MTU 1460 Do not change it from factory default unless necessary Save Cancel Configuration Procedures Internet Connection Type Select PPTP Help Static IP Select Static IP if your ISP provided you all the connection info IP address subnet mask gateway address and DNS address es and enter them in corresponding fields Contact your ISP if you need any help DHCP Also known as Dynamic IP connection type Select itto automatically obtain an IP address and DNS server address for Internet connection if you are not provided with any IP or user name password info by the ISP PPPoE Select PPPoE Point to Point Protocol over Ethernet if your ISP uses a PPPoE connection and provides you
23. Appendix Tenda Wireless Network Connection Network Tasks Choose a wireless network Refresh network list Click an item in the list below to connect to a wireless network in range or to get more information Tenda_OFF02D Connected Ze 2 Set up a wireless network 2 Q For a home or small office H p Security enabled wireless network WPA all Related Tasks 0 Du 1 i EE Unsecured wireless network all networking Tenda _00006E Loi se Change the order of preferred networks Unsecured wireless network all PTCL BB IPT a settings ae Change advanced P Unsecured wireless network alll cr P if Security enabled wireless network WPA aog ng Tenda_otfice p Security enabled wireless network WPAZ Bt w Disconnect Ei Appendix Tenda 3 FAQs This section provides solutions to problems that may occur during installation and operation of the device Read the following if you are running into problems If your problem is not covered here please feel free to go to www tendacn com to find a solution oor email your problems to sSupport tenda com cn or support02 tenda com cn We will be more than happy to help you out as soon as possible 1 Q cannot access the device s management interface What should do Make sure the PWR power LED on the device is on and the SYS LED blinks normally Make sure all cables are correctly connected and the corresponding LAN LED on the device
24. G Router Mode and click Next Wizard Wizard Help SW Home 3G 4G Router Mode In this mode the router acquires Internet access through an 3G 4G Router Mode activated 3G 4G USB modem which is attached to its USB Universal Repeater Mode port Wired WAN access is disabled Wireless Router Mode In this M Auto switch System Mode mode the router acquires Internet access through a wired WAN port 3G 4G access is disabled Universal Repeater Also known as Client plus AP Mode In this mode the router Wireless Router Mode fe 3G 4G Priority Ethernet Priority Configure 3G 4G Internet connection settings and then click Next If you are not sure of which service provider to use select Auto P Quick Setup Tenda Wizard Wizard Country Service Provider ISP APN Dial Number User Name Password UK Vodafone UK Vodafone UK Internet EL web Previous Help 3G 4G Router Mode In this mode the router acquires Internet access through an activated 3G 4G USB modem which is attached to its USB port Wired WAN access is disabled Wireless Router Mode In this mode the router acquires Internet access through a wired WAN port 3G 4G access is disabled Universal Repeater Also known as Client plus AP Mode In this mode the router acquires Internet access from a remote wireless device and provides access to clients in the meantime Configure your wireless network SSID C
25. Internet connection types are supported for the wired WAN connection Ethernet DHCP PPPOE PPTP L2TP and Static IP For PPTP L2TP and Static IP see 2 2 WAN Settings Universal Repeater Mode Select Universal Repeater Mode and click Next ue fi Quick Setup Tenda Wizard Wizard Help 3G 4G Router Mode In this C Wireless Router Mode mode the router acquires Internet access through an 3G 4G Router Mode activated 3G 4G USB modem which is attached to its USB port Wired WAN access is disabled Wireless Router Mode In this Auto switch System Mode mode the router acquires Internet access through a wired WAN port 3G 4G access is disabled Universal Repeater Also known as Client plus AP Mode In this mode the router acquires Internet access from a remote wireless device and provides access to clients in the meantime 3G 4G Priority Ethernet Priority Enter or select the SSID MAC Channel and security settings exactly the same as the remote AP and then click Next Tenda Wizard Wizard Remote AF s SSID Tenda_C eDA50 Remote AF s MAC CB3A 35 80 80 80 Example c 3a 35 30 10 b8 Remote AF s Channel Please select link AF s security mode from below and enter its security key Security Mode WPA PSK Cipher Type AES Security Key 12345678 Select SSID MAC Address a Security signal St Tenda _C8DA50 C 3A 35 60 80 80 WPAIAES 59 Configure your wireless network
26. K on the Local Area Connection Properties window see Step 3 for the screenshot Py Appendix Tenda 2 Join Your Wireless Network Pip To join your wireless network the PC you use must have an installed wireless network adapter If not install one The device s SSID is Tenda _XXXXXX by default where XXXXXX is the last six characters of its MAC address You can find the MAC address and or SSID on the label attached to the device s bottom Windows 7 L Step 1 Click iil or from the right bottom of your desktop Step 2 Double click the name of the wireless network SSID you wish to join and then follow onscreen instructions Currently connected to A Network 4 i gt Internet access Wireless Network Connection a Tenda_OFFO2D wat V Connect automatically Tenda_5 oul Default 5G Za Default_2 4G Za 123 Tenda_020070 WAYOS Open Network and Sharing Center When Connected appears next to the selected wireless network SSID you have successfully connected to it H Appendix Tenda Currently connected to Ch Network A Internet access L Identifying Tenda_OFFO2D No Internet access Wireless Network Connection A Tenda_OFFO2D Connected Af Tenda_5 Za Default_5G oul Default 2 46 Za 2 d Tenda_020070 oul ol ks be H Be oe E el Open Network and Sharing Center Windows XP Step 1 Right click My Network Places and select Properties di
27. N Speed DNS Settings MAC Clone DHCP Server DHCP Client List WAN Settings Internet Connection Type IP Address Subnet Mask Gateway Primary DNS Secondary DNS MTU Configuration Procedures Internet Connection Type Static IP 223 0 0 214 255 255 255 0 223 0 0 1 2 2 2 2 4444 1500 Do not change it from factory default unless necessary save Cancel Select Static IP Help Static IP Select Static IP if your ISP provided you all the connection info IP address subnet mask gateway address and DNS address es and enter them in corresponding fields Contact your ISP if you need any help DHCP Also known as Dynamic IP connection type Select itto automatically obtain an IP address and DNS server address for Internet connection if you are not provided with any IP or user name password info by the ISP os B Features A Configurations Tenda IP Address Subnet Mask Gateway Primary DNS Secondary DNS Enter the information provided by your ISP Click Save to save your settings L2TP L2TP Layer 2 Tunneling Protocol is a network protocol that enables the secure transfer of data from a remote client to a private enterprise server by creating a VPN across TCP IP based data Enter your ISP provided information to establish a connection LAN Settings WAN Settings Help WAN Settings Internet Connection Type gt Static IP Select Static IP if your ISP provided y
28. PnP Client Filter IP Range Uplink Downlink Enable Edit Delete 1 192 168 0 125 125 32 256 d Edit Delete Cancel Zoe 1M 128KByte s The volume of uplink traffic downlink traffic should not be larger than that allowed on your device s WAN Internet port Consult your ISP if you are not sure of the total volume of Internet traffic that you can have The bandwidth for ADSL DSL line usually refers to the download bandwidth 4 6 Client Filter Available only in 4G600 This section allows you to set the times specific clients can or cannot access the Internet via the devices IP addresses and service port Note that this feature is unavailable in 3G 4G Router Mode iss i Features A Configurations Tenda Advanced DDNS Settings Client Filter Help Bandwidth Control Enable Client Filter 7 This section allows you to set the times specific clients can Default Deny H Access from clients NOT included in below list to or cannot access the Internet UPnP Internet via the devices assigned IP DMZ Host addresses and port Client Filter numbers You can setthe Day access restriction or Remote Web Management Mode Pot Type Time Action permission in details Be sure SMTWTFS to statically assign IP address of the devices you wish to filter Delete All Add for this function to be consistent For more information see User Guide Cancel Tips To add a newrule simply click the Add button to edit an existing rule si
29. User Guide www tendacn com 3G 4G Wireless N150 N300 Router Copyright Statement Tenda is the registered trademark of Shenzhen Tenda Technology Co Ltd All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders Copyright of the whole product as integration including its accessories and software belongs to Shenzhen Tenda Technology Co Ltd No part of this publication can be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means without the prior written permission of Shenzhen Tenda Technology Co Ltd If you would like to know more about our product information please visit our website at http www tendacn com Disclaimer Pictures images and product specifications herein are for references only To improve internal design operational function and or reliability Tenda reserves the right to make changes to the products described in this document without obligation to notify any person or organization of such revisions or changes Tenda does not assume any liability that may occur due to the use or application of the product or circuit layout s described herein Every effort has been made in the preparation of this document to ensure accuracy of the contents but all statements information and recommendations in this document do not constitute the warranty of any kind express or impl
30. When a certain feature does not take effect or the device is malfunctioning try rebooting the device Time amp Date Reboot Help Firmware Upgrade Click the button below to restart your router Rebooting the device activates Reboot new settings All connections will be disconnected automatically while rebooting Backup amp Restore Restore to Factory Default Change Password Logs Reboot os B Features A Configurations Tenda IV Appendix 1 Configure Your PC Windows 7 Step 1 Click the icon on the right bottom corner of your desktop Step 2 Click Open Network and Sharing Center Currently connected to Se Unidentified network iia No Internet access m 11 18 2013 2 30 PM Vip lf you cannot find the icon on the right bottom corner of your desktop follow steps below Click Start gt Control Panel gt Network and Internet gt Network and Sharing Center iv Appendix Tenda Step 3 Click Local Area Connection gt Properties A kel bs zc Network and Internet Network and Sharing Center O Local Area Connection Status Control Panel Ho Change adapter sett Change advanced sh settings No Internet access No Internet Enabled 03 40 31 1 0 Gbps for VPN connection or set up a up or VPN network connection See also sj Work computers or change sharing HomeGroup Internet Options d D Intel R PRO 1000 MT Network Connection This connection uses the fol
31. ave registered with your DDNS service provider Here in this example enter 123456 Domain Name Enter the DDNS domain name you have registered with your DDNS service provider Here in this example enter tenda dyndns org Click Save to save your settings DDNS Settings DDNS Settings DMZ Host DNS Settings UPnP DDNS Serice Provider Remote Web Management User Name Password Domain Name M Enable DDNS dyndns org Register Now tenda tenda dyndns org Save Cancel Advanced Help DDNS makes it possible to associate a stable domain name with a dynamically changing WAN IP address So you can access or establish web FTP severs etc on PCs in LAN without worrying about a changing IP Before configuring any DDNS settings click Register Now to register a domain name with your DDNS service provider on its website DDNS Service Provider Select your DDNS service provider from the drop down menu and enter the user name password and domain name Host Name that you registered with your DDNS service provider Click Remote Web Management enable the Remote Web Management feature enter 8090 in the Port field 218 88 93 33 in the IP Address field and then click Save to save your settings DDNS Settings Remote WEB Management DMZ Host SA E UPnP Port 8090 Remote Web Management IP Address Now you can access your device from the Internet by typing 218 88 93 33 save Can
32. away from electrical appliances such as electromagnetic cooker and cordless phone etc to avoid electromagnetic interference 3G 4G Router Mode By connecting an activated 3G 4G USB modem to your device and it gives you the freedom to roam while staying connected to the Internet Insert a 3G 4G USB modem to the device Connect the device to a power outlet Connect your desktop notebook and smart phone etc to the device Gp Quick Setup Tenda Ethernet Cable N A x Notebook Wireless Router Mode In this mode your device functions as a common wireless router Simply connect it to an Internet enabled DSL fiber optical cable modem Connect the WAN port of the device to an Internet enabled DSL fiber optical cable modem Connect the modem and the device to a power outlet Connect your desktop notebook and smart phone to the device 3G 4G Wireless Router Smart Phone ge E Power Outlet Internet DSL Modem Fiber Optical Modem Cable Modem Desktop Ethernet Cable L Ethernet Cable Phone Cable Fiber TV Cable AEA L Notebook P Quick Setup Tenda Universal Repeater Mode The universal repeater feature can be used to extend your existing wireless network coverage Connect the device to a power outlet Connect your desktop notebook and smart phone to the device 3G 4G Wireless Router Internet vu Ethernet Cable Wireless Router Notebook
33. ble on the router for one device for UPnP a special purpose service DMZ Host IP 192 168 0 100 such as Internet gaming or video conferencing Be sure to statically set the IP Address of the DMZ host for this function to be consistent Enter the static IP address ofthe PC on your LAN which you want to set as a DMZ host Once enabled the DMZ hostloses protection from device s firewall and becomes Remote Web Management Save Cancel vulnerable to attacks Configuration Procedures DMZ Host IP The IP address of the device for which the router s firewall au A Features A Configurations Tenda will be disabled Be sure to statically set the IP address of the device that serves as a DMZ host for this function to be consistent Enable Check to enable the DMZ host functionality Click Save to save your settings Zoe Security softwares such as anti virus softwares and OS built in firewall etc may affect the DMZ host feature Disable them if the DMZ host fails 4 3 UPNP The Universal Plug and Play UPnP feature allows network devices such as computers from the Internet to access resources on local host or devices as needed UPnP enabled devices can be discovered automatically by the UPnP service application on the LAN If you use applications such as multiplayer gaming peer to peer connections real time communications such as instant messaging or remote assistance a feature in Windows XP you
34. by performing a scan to see whats available When enabled your wireless network is visible to any Channel Bandwidth 20 Ce 20 40 ere 2442MHz Channel 7 wireless clients within coverage when they scan fora save Cancel wireless network when disabled your wireless network is invisible and thus secure Configuration Procedures SSID This is the public name of your wireless network Channel Select a channel or select Auto to let system automatically select one for your wireless network to operate on if you are unsure of which channel to use The best selection is a channel that is the least used by neighboring networks Click Save to save your settings Pi Features A Configurations Tenda LH 802 11 Mode Select a correct network mode according to your wireless clients Knowledge Center 11b mode This network mode delivers wireless speed up to 11Mbps and is only compatible with 11b wireless clients 11g mode This network mode delivers wireless speed up to 54Mbps and is only compatible with 11g wireless clients 11b g mixed mode This network mode delivers wireless speed up to 54Mbps and is compatible with 11b g wireless clients 11b g n mixed mode This network mode delivers wireless speed up to 300Mbps and is compatible with 11b g n wireless clients BSSID This is the MAC address of the device s wireless interface SSID Broadcast This option allows you to have your wireless network nam
35. cel Advanced Help The Remote Web Management feature allows the Router to be managed from the Internet via a web browser To use this feature Check the Enable Remote Web Management box and specify a Remote Management Port Port Remote admin port the port used to access the device from Internet or external networks your device s domain name into your browser s address or location field on your PC ao B Features A Configurations Tenda 218 88 93 33 followed by a colon and the remote management port number Here in this example enter http tenda dyndns org 8090 4 2 DMZ Host The DMZ De Militarized Zone function disables the firewall on the router for one device for a special purpose service such as Internet gaming or video conferencing applications that are not compatible with NAT Network Address Translation Click Advanced gt DMZ Host to enter the screen below Anote DMZ host poses a security risk A computer configured as the DMZ host loses much of the protection of the firewall and becomes vulnerable to attacks from external networks Hackers may use the DMZ host computer to attack other computers on your network Advanced DDNS Settings DMZ Host Help DMZ Host Note Once aPC is setto a DMZ host it will be completely exposed to Internet and may be The DMZ De Militarized Zone vulnerable to attack as firewall settings become inoperative function disables the firewall Ena
36. ction Type User Name Password MTU Configuration Procedures 1492 Do not change it from factory default unless necessary save Cancel Internet Connection Type Select PPPoE Bi Features A Configurations Tenda Help Static IP Select Static IP if your ISP provided you all the connection info IP address subnet mask gateway address and DNS address es and enter them in corresponding fields Contact your ISP if you need any help DHCP Also known as Dynamic IP connection type Select itto automatically obtain an IP address and DNS server address for Internet connection if you are not provided with any IP or user name password info by the ISP User Name Enter the ISP login name Password Enter the ISP login password Click Save to save your settings LA Knowledge Center MTU The MTU maximum transmission unit is the largest data packet a network device transmits The normal MTU value for most Ethernet networks is 1500 bytes or 1492 bytes for PPPoE connections For some ISPs you might need to change the MTU This is rarely required and should not be done unless you are Sure it is necessary for your ISP connection For more information see WAN MTU Setup Static IP Static IP is a connection mode that allows you to specify the Static IP information provided by your ISP or that corresponds with your existing networking equipment LAN Settings WAN Settings WA
37. current rule to take effect Here in this example select Mon Tue Wed Thur and Fri Click Save to save your settings Advanced DDNS Settings Client Filter Setting Help Bandwidth Control Filter Mode Deny This section allows you to set the times specific clients can DMZ Host Description access webpage or cannot access the Internet via the devices assigned IP P 192 168 0 110 192 168 0 111 numbers You can setthe Client Filter Specify a single IP address or an IP range access restriction or UPnP Remote Web Management permission in details Be sure WAN PortRange 80 80 to statically assign IP address of the devices you wish to filter Type Both fa for this function to be consistent For more Time 08 RH 00 RH 18 RH 00 E information see User Guide Day EveyDay Sun W Mon M Tue M Wed M Thu Tips To add a new rule simply click the Add button to M Fri T Sat i isti j edit an existing rule simply click the Edit or Change button next to it Deny Disallow clients at specified IP address es to access Internet Cancel Enable Client Filter Check to enable the client filter feature Select Allow from the Default drop down list and then click Save s Features y Configurations Tenda DDNS Settings Client Filter Bandwidth Control Enable Client Filter DMZ Host Default UPnP Client Filter Remote Web Management 192 168 0 110 192 168 0 111 Zoe The valid service
38. date info shall be set correctly first either manually or automatically save Cancel Go to the Status screen to make sure the system time is correctly updated 5 2 Firmware Upgrade Click Tools gt Firmware Upgrade to enter the configuration screen Firmware upgrade is released periodically to improve the functionality of your device and also to add new features If you run into a problem with a specific feature of the device log on to our Website http www tendacn com to download the latest firmware to update your device Anote Before you upgrade the firmware make sure you are having a correct firmware A wrong firmware may damage the device It is advisable that you upgrade the device s firmware over a wired connection DO NOT disconnect the power connection to the device when the upgrade is in process otherwise the router may be permanently damaged Configuration Procedures vu B Features A Configurations Tenda Click Browse Time amp Date Fireware Upgrade Help Firmware Upgrade Use this section to update your routers software for better functionality or new features To download latest firmware Select a Software File Upgrade go to www tendacn com Browse Click to locate and Current System Version 4G630_V1 0 0 1_EN Release Date Dec 11 2013 select the latest firmware for update Note Do not power off the router while upgrading otherwise it may be permanently damaged Upgrade Click
39. e SSID publicly broadcast or if you choose to disable it the SSID will be hidden Channel Bandwidth Select a proper channel bandwidth to enhance wireless performance This option is available only in 802 11b g n mixed mode Maximum wireless speed in the channel bandwidth of 20 40 is 2 times in 20 Extension Channel This is used to ensure N speeds for 802 11n devices on the network This option is available only in 11b g n mixed mode with the channel bandwidth of 20 40 3 2 Security Click Wireless gt Security to enter the configuration screen Here you can define a security key to secure your wireless network against unauthorized accesses ua B Features A Configurations Tenda Wireless Wireless Security Help SSID Tenda_38DDC9 WEP Key Select Open Shared or Mixed WEP from the Security Mode WPA2 PSK corresponding drop down list ASCII Enter 5 or 13 ASCII Cipher Type CG AES TKIP C TKIP amp AES characters Hex Enter 10 or 16 Hex characters Security Key 12345678 WPA WPA2 You can select Access Control Connection Status either personal or mixed only Key Renewal Interval 3600 seconds Key will not be updated if Key Renewal ensure that either one you Interval is set to 0 select is supported on your wireless clients WPS Settings Important If you are an advanced user and have Ge Disable Enable configured security mode before you can select any mode you like only to assure that the one you choose
40. e PPPoE or Dynamic IP Internet connection type You need to change the MTU size Try changing the MTU to 1450 or 1400 If this does not help gradually reduce the MTU from the maximum value until the problem disappears For details see WAN MTU Setup My Appendix Tenda 4 Remove Wireless Network from Your PC When you change your wireless network For example change your device s SSID or security key the old wireless settings on your PC will not be updated accordingly you must manually remove them from your PC otherwise you may not be able to wirelessly connect to the device This section explains how to remove a wireless network from your PC Windows 7 Right click the Network icon and select Properties Map network dive Disconnect network drive Create shortcut Delete Properties Select Manage Wireless Networks 2 67 2808 a 66 F gt Control Panel Network and Internet gt Network and Sharing Center 4 e Control Panel Home e View your basic network information and set up connections _ Manage wireless networks SE gt See full map Ss x Change adapter settings TEST PC Tenda_home Internet Change advanced sharing This computer settings l g View your active networks Connect or disconnect A Tenda home ccess type we Internet aie Connections dl Wireless Network Connection 8 Public network Gann havea Change your networking settings CN Set up a new co
41. eater Mode port Wired WAN access is disabled Wireless Router Mode In this M Auto switch System Mode mode the router acquires Internet access through a wired WAN port 3G 4G access is disabled Universal Repeater Also known as Client plus AP Mode In this mode the router acquires Internet access from a remote wireless device and provides access to clients in the meantime Ge 3G 4G Priority Ethernet Priority 2 Select DHCP and click Next Wizard Wizard Help SW Home 3G 4G Router Mode In this Internet Connection Type DHCP mode the router acquires Internet access through an activated 3G 4G USB modem Previous which is attached to its USB port Wired WAN access is disabled Configure your wireless network SSID Channel Key and then click Next 2g Quick Setup Tenda Wizard Wizard SSID Tenda_38DDC9 Channel Auto 12345678 Security Mode Tenda optimizes wireless security Default AES under WPA2 PSK will effectively protect your network against unauthorized accesses Previous 4 Click Finish and wait for the device to restart Wizard Wizard Configurations complete Previous Finish Wireless Router Mode PPPoE Select Wireless Router Mode and click Next o fi Quick Setup Tenda Help 3G 4G Router Mode In this mode the router will try 3G 4G access only WAN access is disabled Wireless Router Mode In this mode the router will try WAN access only 3G 4G access is disab
42. ed Universal Repeater Also known as Client plus AP Mode In this mode the router acquires Internet access from a remote wireless device and provides access to clients in the meantime Configure your wireless network SSID Channel Key and then click Next vw Wi Quick Setup Tenda GO Zoe Wizard Wizard G Home SSID Tenda_38DDC9 Channel Auto 12345678 Security Mode Tenda optimizes wireless security Default AES under WPA2 PSK will effectively protect your network against unauthorized accesses Ifthis field is left blank your wireless network is not secured Previous Click Finish and wait for the device to restart Wizard Wizard L2 Home Configurations complete Previous Finish Help 3G 4G Router Mode In this mode the router acquires Internet access through an activated 3G 4G USB modem which is attached to its USB port Wired WAN access is disabled Wireless Router Mode In this mode the router acquires Internet access through a wired WAN port 3G 4G access is disabled Universal Repeater Also known as Client plus AP Mode In this mode the router acquires Internet access from a remote wireless device and provides access to clients in the meantime Help 3G 4G Router Mode In this mode the router will try 3G 4G access only WAN access is disabled Wireless Router Mode In this mode the router will try WAN access only 3G 4G access is disabled Five
43. es an L2TP connection E Select PPTP Point to Point Tunneling Protocol if your ISP uses a PPTP connection DHCP DHCP or Dynamic IP is a connection mode that allows the device to automatically acquire IP information from your ISP or your existing networking equipment o A Features A Configurations Tenda LAN Settings WAN Settings WAN Speed DNS Settings MAC Clone DHCP Server DHCP Client List WAN Settings Internet Connection Type MTU Configuration Procedures DHCP gt 1500 Do not change it from factory default unless necessary Save Cancel Internet Connection Type Select DHCP Click Save to save your settings PPPoE Help Static IP Select Static IP if your ISP provided you all the connection info IP address subnet mask gateway address and DNS address es and enter them in corresponding fields Contact your ISP if you need any help DHCP Also known as Dynamic IP connection type Select itto automatically obtain an IP address and DNS server address for Internet connection if you are not provided with any IP or user name password info by the ISP PPPoE is a connection mode associated with some DSL connections that requires user name and password Contact your ISP if you need assistance with these login credentials LAN Settings WAN Settings WAN Speed DNS Settings MAC Clone DHCP Server DHCP Client List WAN Settings Internet Conne
44. figuration screen Vip Configured time and date settings will be lost if the device gets disconnected from power supply However it will be updated automatically when the device reconnects to the Internet To activate time based features e g Client Filter the time and date settings should be set correctly first either manually or automatically A To synchronize with Internet time servers Internet Time Server Check to enable the feature If enabled time and date will be updated automatically from the Internet Sync Interval Specify a time interval for periodic update of time and date information from the Internet Time Zone Select your current time zone 4 Click Save to save your settings Go to the Status screen to make sure the system time is correctly updated so A Features A Configurations Tenda Time amp Date Firmware Upgrade Backup amp Restore Restore to Factory Default Change Password Logs Reboot Note Time amp Date Internet Time Server Sync Interval Time Zone Input Time And Date 2 hours GMT 08 00 Bejing China Hong 2013 12 p16 18 43 11 Copy Local Time Save Cancel Help This page is used to setthe device s system time You can choose to setthe time manually or getthe GMT time from the Internet and the system will automatically connect to NTP server to synchronize the time Note System time will be lost when the device is disc
45. figurations Tenda 3G 4G Traffic Statistics Help IG AG Traffic Statistics Here is only for monitoring Internet data traffic passing Upload Speed 0 06 KB s through the 3G 4G modem that is attached to the Download Speed 0 16 KB s router TXData 47 11 KB RXData 246 6 KB Connected Time 00 09 56 Total Statistics 9937 KB Clear Note This traffic statistics is for references only For actual statistics info consult your ISP WAN Status in Wireless Router Mode Status WAN Status Help Internet Connection Status Connected Here you can view the WAN status LAN status wireless WANIP 223 0 0 214 status and system status of the device SubnetMask 255 255 255 0 Gateway 223 0 0 1 Primary DNS Serer 2 2 2 2 Secondary DNS Serer 4444 Internet Connection Type Dynamic IP Cor Disconnect WAN Status in Universal Repeater Mode Status WAN Status Help Repeater Status Connected Here you can view the WAN status LAN status wireless 20 Fim Features y Configurations Tenda GI WAN IP Subnet Mask Gateway Primary DNS Server Secondary DNS Server This type of information appears only if the router successfully connects to the Internet via a PPPoE or a DHCP dynamic IP connection However if you connect the router to the Internet with static IP settings provided by your ISP these fields will display the settings you entered whether the router successfully connects to the Internet or not If there is no available sec
46. ging the MTU value fixes one problem but causes another Leave the MTU unchanged unless one of these situations occurs A You have problems connecting to your ISP or other Internet service and either your ISP or our technical support suggests changing the MTU value Below Web based applications might require an MTU change A secure Website that does not open or displays only part of a Web a B Features A Configurations Tenda page Yahoo email MSN portal B You use VPN and encounter serious performance problems C You used a program to optimize MTU for performance reasons and now you have connectivity or performance problems If you suspect an MTU problem try changing the MTU to 1400 If this does not help gradually reduce the MTU from the maximum value of 1500 until the problem disappears The common MTU sizes and applications are listed in the table below 1500 Typical for connections that do not use PPPoE or VPN 1492 Used in PPPoE environments Maximum size to use for pinging Larger packets are 1472 fragmented 1468 Used in some DHCP environments 1436 Used in PPTP environments or with VPN Note A wrong improper MTU value may cause Internet communication problems For example you may be unable to access certain Websites frames within Websites secure login pages FTP or POP servers 2 3 WAN Speed Available only in Wireless Router Mode Click Basic gt WAN Speed to enter the configuration
47. hannel Key and then click Next Wizard Wizard GO SSID Channel Security Mode secured Key Tenda_38DDC9 Auto 12345678 Tenda optimizes wireless security Default AES under WPA2 PSK will effectively protect your network against unauthorized accesses If this field is left blank your wireless network is not Previous Click Finish and wait for the device to restart Wizard Configurations complete Previous Finish Help 3G 4G Router Mode In this mode the router acquires Internet access through an activated 3G 4G USB modem which is attached to its USB port Wired WAN access is disabled Wireless Router Mode In this mode the router acquires Internet access through a wired WAN port 3G 4G access is disabled Universal Repeater Also known as Client plus AP Mode In this mode the router acquires Internet access from a remote wireless device and provides access to clients in the meantime Help 3G 4G Router Mode In this mode the router will try 3G 4G access only WAN access is disabled Wireless Router Mode In this mode the router will try WAN access only 3G 4G access is disabled o fi Quick Setup Tenda Wireless Router Mode DHCP Select Wireless Router Mode and click Next Wizard Help 3G 4G Router Mode In this mode the router acquires Internet access through an 3G 4G Router Mode activated 3G 4G USB modem which is attached to its USB Universal Rep
48. ied About this Manual Thank you for choosing Tenda Before you start please read this User Guide which instructs you to install and configure your device This User Guide is applicable to 4G600 and 4G630 Unless otherwise specified the 4G630 is used as an example throughout this User Guide Convention This user guide uses the following formats to highlight special messages This format is used to highlight information of importance or special interest Ignoring this type of note may result in ineffective configurations loss of data or damage to device This format is used to highlight a procedure that will save time or resources LU Knowledge Center Description of fields on the device GUI Technical Support Website http www tendacn com Email support02 tenda com cn Skype tendasz YouTube Tendasz1999 Hotline 1 800 570 5892 USA 061 1300787922 Australia 064 800787922 New Zealand 0852 36120883 Hong Kong s Contents ADOUC CNIS MANUAL ageet II CO 6 W110 E II TeCMMICAY OUP POM EE II T PROGUUCE OF Crvlew E 1 UR Ge EE l 2 Cetin e Re YOUR DOV O eers e a re a Ne l 2 1 What It Looks E EE l PA E A b EE 2 GN e EE SE 3 Day BEE 4 DT QUICK Sep ea E A E E E EE E E 5 OR EE KE EE A P whe E E A N E A EE T E T 5 3G 4G Router Mode ssnnnssnnnssennssennssersssersssersseersssrossrrosseroserroserrsserrssrersserossereserreseere 5 Wireless Outer MOdG EE 6 Universal Repea
49. in your wireless network select Disable a4 B Features A Configurations Tenda B If you want to allow ONLY the specified wireless clients to join your wireless network select Allow C If you want to disallow ONLY the specified wireless clients to join your wireless network select Deny Wireless Access Control Application Example To only allow your own notebook at the MAC address of C8 3A 35 CC 34 25 to join your wireless network Select Allow Enter C8 3A 35 C0C 34 25 Click Add to add the MAC address to the MAC address list Click Save to save your settings Basic Security Access Control Connection Status Vip Wireless Access Control Configure the wireless interface MAC address filtering policy MAC Filter Allow MAC address Action A 35 LG 34 25 Index MAC Address Delete 1 C8 3A 35 C0 34 25 Delete Cancel Wireless Help Specify a list of devices to allow or disallow a connection to your wireless network via the devices MAC addresses To deactivate this feature select Disable to activate it select Allow or Deny If you don t want to configure the complex wireless security settings and want to disallow others to join your wireless network you can configure a wireless access control rule to allow only your own wireless device 3 4 Connection Status Click Wireless gt Connection Status Here you can see a list of wireless P
50. interface Here you can configure the WAN speed and duplex mode z2 B Features A Configurations Tenda LAN Settings WAN Speed Help WAN Settings Speed Duplex pws Aging and the lenath of an Ethernet cable may reduce WAN Speed transmission capability In this Save Cancel case select 10M Full Duplex or the mode specified by the MAC Clone ISP from the Speed Duplex drop down listto improve DHCP Server performance DNS Settings DHCP Client List Zoe The device operates in Auto Auto negotiation mode by default Usually it works for most cases In some situations you might need to change the speed duplex mode For example if the cable connected to your device s WAN port is longer than 100m you may need to use 10M full duplex or 10M half duplex for better performance Ensure that your device s WAN port operates with the same speed and duplex mode as the remote link partner Otherwise your device s WAN port may not receive and send data 2 4 DNS Settings Click Basic gt DNS Settings to enter the configuration interface a B Features A Configurations Tenda LAN Settings DNS Settings Help WAN Settings DNS Settings M DNS server translates or resolves domain names into Primary DNS Address 202 96 134 33 IP addresses To manually configure the DNS server WAN Speed DNS Settings Secondary DNS Address 202 96 128 68 addresses check the Set MAC Clone DNS Manually box to obtain DNS server IP add
51. is also supported by your wireless clients if you are new to networking and have never configured this parameter before we suggest that you select WPA PSK or WPA2 PSK Save Cancel Configuration Procedures Configure Security Mode Cipher Type and Security Key Click Save to save your settings LA Knowledge Center WEP WEP is intended to provide data confidentiality comparable to that of a traditional wired network Open If selected wireless speed can reach up to 54Mbps Shared If selected wireless speed can reach up to 54Mbps Default Key Select a key to be effective for the current WEP encryption For example if you select Key 2 wireless clients must join your wireless network using this Key 2 WPA PSK WPA personal supports AES and TKIP cipher types WPA2 PSK WPA2 personal supports AES TKIP and TKIP AES cipher types Mixed WPA WPA2 PSK If selected both WPA PSK and WPA2 PSK secured wireless clients can join your wireless network AES If selected wireless speed can reach up to 300Mbps B Features A Configurations Tenda TKIP If selected wireless speed can reach up to 54Mbps TKIP amp AES If selected both AES and TKIP secured wireless clients can join your wireless network Key Renewal Interval Enter a valid time period for the key to be changed WPS Wi Fi Protected Setup makes it easy for home users who know little of wireless security to establish a home network as well as to add
52. is on Verify that your PC s TCP IP settings are configured correctly If you select the Use the following IP address option set your PC s IP address to any IP address between 192 168 0 2 192 168 0 254 Or you can select the Obtain an IP address automatically option Delete your browser cache and cookies or use a new browser Make sure you enter 192 168 0 1 in your browser s address bar Open your browser and click Tools gt Internet Options gt Connections gt LAN Settings uncheck the Use a proxy server for your LAN option Press the WPS Reset button for over 6 seconds to restore your device to factory default settings Then log in to your device again 2 Q changed the login password and unfortunately forget it What should do Press the WPS Reset button for over 6 seconds to restore your device to factory default settings 3 Q My computer shows an IP address conflict error when it connects to the ay Appendix Tenda device What should I do Make sure there are no other DHCP servers on your LAN or other DHCP servers are disabled Make sure the device s LAN IP is not used by other devices on your LAN The device s default LAN IP address is 192 168 0 1 Make sure the statically assigned IP addresses to the PC s on LAN are not used by others device s 4 Q cannot access email and the Internet Some Websites do not open What should do This problem mainly happens to users who use th
53. led 3G 4G Router Mode Dials up an Internet connection using an inserted 3G 4G network adapter Universal Repeater This is the Client plus AP Mode In this mode the router acquires Help 3G 4G Router Mode In this mode the router will try 3G 4G access only WAN access is disabled Wireless Router Mode In this mode the router will try WAN access only 3G 4G access is disabled Wizard Wizard Help 3G 4G Router Mode In this mode the router acquires Internet access through an 3G 4G Router Mode activated 3G 4G USB modem which is attached to its USB Universal Repeater Mode port Wired WAN access is disabled Wireless Router Mode In this M Auto switch System Mode mode the router acquires Internet access through a wired WAN port 3G 4G access is disabled Universal Repeater Also known as Client plus AP Mode In this mode the router acquires Internet access from a remote wireless device and provides access to clients in the meantime Ge 3G 4G Priority Ethernet Priority Select PPPoE enter the PPPoE User Name Password and click Next Wizard Wizard Help 3G 4G Router Mode In this Internet Connection Type PPPOE mode the router acquires Internet access through an PPPoE User Name activated 3G 4G USB modem which is attached to its USB disabled Wireless Router Mode In this Previous mode the router acquires RE Internet access through a wired WAN port 3G 4G access is disabl
54. lowing items JZ Q05 Packet Scheduler J File and Printer Sharing for Microsoft Networks at Intemet Protocol Version 6 TCP IP v6 S Intemet Protocol Version A TCP Pwd wi Link Layer Topology Discovery Mapper Lo Driver wi Link Layer Topology Discovery Responder Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks My Appendix Tenda Step 5 Select Obtain an IP address automatically and Obtain DNS server address automatically and click OK Internet Protocol Version 4 TCP IPv4 Properties General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically gt Use the following IP address IF address Subnet mask Default gateway Obtain DNS server address automatically CC Use the following DNS server addresses Preferred DNS server Alternate ONS server Validate settings upon exit Step 6 Click OK on the Local Area Connection Properties window see Step 4 for the screenshot Windows XP Step 1 Right click My Network Places on your desktop and select Properties D Ka SE Open Explore Search for Computers Map Network Drive Disconnect Network Drive Create Shortcut
55. lt Subnet Mask is 255 255 255 0 for example Click Basic gt WAN Settings to configure your Internet connection settings 3G 4G Router Mode oa B Features A Configurations Tenda Tenda LAN Settings WAN Settings Help WAN Settings Country UK Connect on Demand is specially recommended for those who do not need to always stay connected and wantto save available volume DNS Settings l Service Provider Vodafone Pre pay DHCP Server ISP Vodafone Pre pay i DHCP Client List of Internet traffic or bill In this connection mode a 3G 4G connection automatically starts when there is outbound traffic to the Internet and it automatically terminates to save your bill ifthere is no Internet activity APN pp vodafone co uk Dial Number 99F Advanced PPP Settings UserName Password Select your connect mode Click Save and reboot the device to acitvate your settings Ge Connect Automatically Connect automatically to the Internet after system reboot or connection failure Connect Manually Require the user to manually connect to Internet before each session Connect On Demand Re establish connection to the Internet only when there is data transmitting Max Idle Time 60 C Connect During Specified Time Period Connect automatically to Internet during a specified time length Note To activate te Connec during Specified Time feature you must first configure system time Tools gt Time amp Date for
56. may need to enable Universal Plug and Play UPnP for better experience Click Advanced gt UPnP to enter the configuration screen The UPnP feature is enabled by default Advanced DDNS Settings Help DMZ Host Enable UPnP M The Universal Plug and Play UPnP feature allows network Genie devices such as computers from Internet to access Remote Web Management resources on local host or devices as needed UPnP enabled devices can be discovered automatically by the UPnP service application on the LAN Presently itis only supported by operating systems like Windows ME and Windows XP or later a B Features A Configurations Tenda 4 4 Remote Web Management The Remote Web Management allows the device to be configured and managed remotely from the Internet via a Web browser Click Advanced gt Remote Web Management to enter the configuration screen Advanced DDNS Settings Remote WEB Management Help DMZ Host Enable The Remote Web Management feature allows the Router to be managed from the Internet via a web UPnP Remote Web Management i IP Address 0 0 0 0 browser To use this feature Check the Enable Remote Web Management box and specify a Remote Management Port Port Remote admin port the port used to access the device from Internet or external networks IP Enter the IP address of a trusted PC from Internet or Cancel other external networks which you want to authorize to manage
57. me servers We use a numeric IP address allocated by Internet Service Provider ISP to connect to the Internet the address may either be stable static or may change from one session on the Internet to the next dynamic However a numeric address is inconvenient to remember an address which changes unpredictably makes connection impossible The DDNS provider allocates a static host name to the user whenever the user is allocated a new IP address this is communicated to the DDNS provider by software running on a computer or network device at that address the provider distributes the association between the host name and the address to the Internet s DNS servers so that they may resolve DNS queries Thus uninterrupted access to devices and services whose numeric IP address may change is maintained Click Advanced gt DDNS Settings to enter the screen below P Features A Configurations Tenda Advanced DDNS Settings DDNS Settings Help DMZ Host DNS Settings E Enable DDNS DDNS makes it possible to associate a stable domain DDNS Service Provider no ip com Register Now name with a dynamically changing WAN IP address So User Name you can access or establish web FTP severs etc on PCs UPnP Remote Web Management Password in LAN without worrying about a changing IP Before Domain Name configuring any DDNS settings click Register Now to register a domain name with your DDNS service provider on its website DDNS Se
58. mply click the Edit or Change button next to it LA Knowledge Center Default The default policy for the client filter For the packets that do not match the set rule the default rule is applied Filter Mode Specify a filter mode for the rule v Deny Disallow the packets that match the set rule to pass the router For other packets that do not match the set rule the default policy is applied v Allow Allow the packets that match the set rule to pass the router For other packets that do not match the set rule the default policy is applied Client Filter Application Example To prohibit PCs within the IP address range of 192 168 0 110 192 168 0 111 from accessing Web pages during the time period of 8 00 18 00 from Monday to Friday follow the steps below Click Add to add a filter rule Filter Mode Select Deny Description Briefly describe the current rule This field is optional Oo IP Enter 192 168 0 110 as the starting IP address and 192 168 0 111 as the ending IP address so A Features Configurations Tenda WAN Port Range Enter a service port number Here in this example enter 80 in both boxes HTTP port 80 is the standard protocol for Web servers Type Select a protocol for the traffic If you are unsure select Both Time Specify a time period for the current rule to take effect Here in this example select 8 00 18 00 Day Select a day or several days of the week for the
59. nda Lease Time The lease time is a time length that the IP address is assigned to each device before it is refreshed Click Save to save your settings Zoe By default the device functions as a DHCP server Do not disable the DHCP server feature unless you want to manually configure the TCP IP settings for all the PCs on your LAN Lease time will be renewed automatically upon expiry If you are not an advanced user the default DHCP server settings are recommended 2 DHCP Client List Click Basic gt DHCP Client List Here you can see a list of the DHCP dynamic clients if any By viewing this list you can know whether there are unauthorized accesses LAN Settings Static Assignment Help WAN Settings IP Address 192 168 0 The DHCP Client List displays information of devices that have obtained IP addresses from the device s DHCP Server If you would like some MAC Clone Index IP Address MAC Address Delete devices on your network to always have the same IP DHCP Server addresses you can use this Cancel feature and manually add a DHCP Client List DHCP Client List static DHCP Reservation entry for each such device WAN Speed ga WAC Address DNS Settings Refresh Important To activate new settings you must click the Save button Note Remember to reboot INVE 20130508IP 192 168 0 156 c8 9c dce 3b ac 89 23 44 42 device after you finish Host Name IP Address MAC Address Lease Time Also y
60. nnection or network Select the wireless network and click Remove network Py Appendix Tenda k aaa Ea E ec tr Ne OU eu gt Control Panel Network and Internet Manage Wireless Networks v gt Manage wireless networks that use Wireless Network Connection 8 Windows tries to connect to these networks in the order listed below Add Adapter properties Profiletypes Network and Sharing Center Networks you can view modify and reorder 2 wr Tenda_home Security WPA Personal Type Any supported Automatically connect A KK Tenda_AAAABA Security WPA Personal Type Any supported Automatically connect Windows XP Right click My Network Places and select Properties Open Explore Search For Computers Map Network Drive Disconnect Network Drive Create Shortcut Delete Rename Right click Wireless Network Connection and then select Properties Py Appendix Tenda _ LAN or High Speed Internet Create Shortcut Delete Rename Properties Click Wireless Networks select the wireless network name under Preferred networks and then click the Remove button A Local Area Connection Z Properties a KA Genersl Wireless Networks Advanced Available networks To connect to disconnect from or find out more information about wireless networks in range click the button below Prefered networks Automatically connect to available networks
61. ondary DNS server nothing appears in the secondary DNS server field LAN Status LAN Status IF Address 192 168 0 1 Subnet Mask 255 255 255 0 DHCP Server Enabled Anote The DHCP Server is disabled in Universal Repeater Mode Wireless Status Wireless Status Wireless Radio Enabled SSID Tenda _38DDC9 602 11 Mode 11b a n mixed mode channel Auto security Mode Disabled a Features A Configurations Tenda System Status System Status System Time 2013 12 16 17 33 13 Up Time 00 03 47 Firmware Version 4G6630_V1 0 0 1_EN Hardware Version VD LAN MAC Address C6 34 35 38 DD C8 WAN MAC Address C6 34 35 36 DD C8 Connected Clients 4 L Knowledge Center WAN MAC Address The device s current WAN MAC address System Time Current system time on this device The device automatically synchronizes the system time with Internet time servers Up Time Displays the time duration indicating how long the router has been up since startup Up time is recounted and renewed upon power off Connected Clients Displays the number of DHCP clients z2 Features y Configurations Tenda 2 Basic Settings To change the device s login IP address see 2 1 LAN Settings To set up the Internet see 2 2 WAN Settings To set up speed and duplex mode for the WAN port see 2 3 WAN Speed Available only in Wireless Router Mode To configure DNS server see 2 4 DNS Settings To clone MAC address
62. onnected from power supply However it will be updated automatically when the device reconnects to Internet To activate time based features e g firewall the time and date info shall be set correctly first either manually or automatically In the Universal Repeater Mode the Internet Time Server Enable feature is not available so you can only set the time and date manually B To set time and date manually synchronize with your PC Internet Time Server Uncheck to disable the feature Specify the time and date manually or click Copy Local Time to automatically copy your PC s time to the device Click Save to save your settings oo B Features y Configurations Tenda Time amp Date Firmware Upgrade Backup amp Restore Restore to Factory Default Change Password Logs Reboot Time amp Date Internet Time Server Sync Interval Time Zone Input Time And Date E GMT 08 00 Bejing China Hong 142 16 18 43 11 Copy Local Time Help This page is used to setthe device s system time You can choose to set the time manually or getthe GMT time from the Internet and the system will automatically connect to NTP server to synchronize the time Note System time will be lost when the device is disconnected from power supply However it will be updated automatically when the device reconnects to Internet To activate time based features e g firewall the time and
63. ou all the _ L2TP Server Address IP Address connection info IP address subnet mask gateway User Name address and DNS address es and enter them in Password corresponding fields Contact DHCP Server your ISP if you need any help DNS Settings MAC Clone Address Mode Static DHCP Also known as DHCP Client List Dynamic IP connection type IP Address Select itto automatically obtain an IP address and Subnet Mask DNS server address for Internet connection if you are Gateway not provided with any IP or l user name password info by MTU 1458 Do not change it from the ISP PPPoE Select PPPoE Point to Point Protocol over Ethernet if your ISP uses a PPPoE connection and provides you with a PPPoE user name and a PPPoE password Simply enter them in corresponding fields factory default unless necessary save Cancel Configuration Procedures Internet Connection Type Select L2TP L2TP Server Address Enter the L2TP IP address provided by your ISP User Name Enter your L2TP user name 4 Password Enter your L2TP Password Address Mode Select Dynamic if you don t get any IP information from your ISP otherwise select Static Consult your ISP if you are loo B Features A Configurations Tenda not clear IP Address Enter the IP address provided by your ISP Consult your local ISP if you are not clear 9 Subnet Mask Enter the subnet mask Gateway Enter the gateway provided by
64. ou can specify a reserved IP address for a PC on your LAN That PC will always receive the same IP address each time when it accesses the DHCP a7 B Features A Configurations Tenda server Reserved IP addresses could be assigned to servers that require permanent IP settings Static Assignment Application Example To have a PC at the MAC address of 44 37 E6 4F 37 38 always receive the same IP address of 192 168 0 123 LAN Settings Static Assignment Help WAN Settings IP Address 192 168 0 123 The DHCP Client List displays information of devices that WAN Speed have obtained IP addresses from the device s DHCP Server If you would like some MAC Address 44 37 CES CAE 137 DNS Settings MAC Clone Index IP Address MAC Address Delete devices on your network to always have the same IP DHCP Server 1 192 168 0 123 44 37 E6 4F 37 38 Delete addresses you can use this feature and manually add a DHCP Client List static DHCP Reservation entry Cancel for each such device DHCP Client List Important To activate new settings you must click the Refresh Save button Note Remember to reboot device after you finish Host Name IP Address MAC Address Lease Time INVE 20130508IP 192 168 0 156 c8 9c dce 3b ac 89 23 44 42 Configuration Procedures Enter the last number of the IP address you want to reserve Here in this example enter 123 Enter the MAC address of 44 37 E6 4F 37 38 Click Add Click Save
65. port number range is 1 65535 E Allow Access from clients NOT included in below list to Internet Port Type Time SMTWTFS Delete All Cancel Day Add Action Advanced Help This section allows you to set the times specific clients can or cannot access the Internet via the devices assigned IP addresses and port numbers You can set the access restriction or permission in details Be sure to statically assign IP address of the devices you wish to filter for this function to be consistent For more information see User Guide Tips To add a new rule simply click the Add button to edit an existing rule simply click the Edit or Change button next to it Deny Disallow clients at specified IP address es to access Internet If you have not set up the system time for this device click Tools gt Time amp Date to configure correct time and date settings for the rule s to be effective ss A Features A Configurations Tenda 5 Tools To configure system time see 5 1 Time amp Date To upgrade firmware see 5 2 Firmware Upgrade To backup or restore configurations see 5 3 Backup amp Restore To restore factory default settings see 5 4 Restore to Factory Default To change login password see 5 5 Change Password To view logs see 5 6 Logs To restart device see 5 7 Reboot 5 1 Time amp Date Click Tools gt Time amp Date to enter the con
66. resses DHCP Server Cancel from your ISP automatically leave the same box DHCP Client List unchecked Ifthe DNS IP Addresses entered are incorrect web pages will not be able to open Thus itis advisable not to change the default settings here Configuration Procedures DNS Settings Check uncheck to enable disable the DNS settings Primary DNS Address Enter the IP address of the primary DNS server provided by your ISP Secondary DNS Address If a secondary DNS server address is available enter it here This field is optional Click Save to save your settings Anote The default DNS settings are recommended Only change the DNS default settings if you know that your ISP requires specific servers If incorrect DNS settings are configured Webpages may not open 2 5 MAC Clone Available only in Wireless Router Mode Some ISPs Internet Service Providers require end user s MAC address to access their network This feature copies your current PC s MAC address to the device Click Basic gt MAC Clone to enter the configuration screen a4 B Features A Configurations Tenda LAN Settings MAC Clone Help WAN Settings MAC Address C8 34 35 38 DD C3 WAN MAC Address The device s WAN MAC address seen from the Internet side by your ISP Normally you don t need to change its default MAC Clone Save Cancel value Normally you dont need to change the default WAN DHCP Server MAC value However some ISPs may
67. rnal Remote Web Management Save Cancel networks Type http 102 33 66 88 8090 into your browser s address or location field and you can remotely access the router from your home J Knowledge Center IP Address Here you can specify the IP address for remote management If set to 0 0 0 0 the device becomes remotely accessible to all the PCs on the Internet or other external networks Port This is the management port to be open to outside access The default setting is 8080 This can be changed 4 5 Bandwidth Control Available only in 4G600 If there are multiple PCs behind your device competing for limited bandwidth resource then you can use this feature to specify a reasonable amount of ss A Features A Configurations Tenda bandwidth for each such PC so that no one will be over stuffed or starved to death Note that this feature is unavailable in 3G 4G Router Mode Advanced DDNS Settings Bandwidth Control Help Bandwidth Control Bandwidth Control 7 Enable Use this section to manage bandwidth allocation to devices on your LAN Cancel Upload Download Limit Set a limit to regulate Client Filter upload download bandwidth of PCs on the LAN Remote Web Management Upload Download Limit Set a DMZ Host UPnP upload download limit on specified PC s Bandwidth Control Application Example You share a 4M broadband service with your neighbor at the IP address of 192 168 0 125
68. rvice Provider Select your DDNS service provider Cancel from the drop down menu and enter the user name password and domain name Host Name that you registered with your DDNS service provider Zoe To use the DDNS feature you need to have an account with one of the DDNS Service Providers in the drop down list first DDNS Application Example If your ISP gives you a dynamic changing public IP address you want to access your router remotely see 4 4 Remote Web Management but you cannot predict what your router s WAN IP address will be and the address can change frequently In this case you can use a commercial Dynamic DNS service It lets you register your domain to their IP address and forwards traffic directed at your domain to your frequently changing IP address If your DDNS service provider provides you with a DDNS account User Name tenda Password 123456 Domain Name tenda dyndns org and you want to use the PC at the IP address of 218 88 93 33 to remotely access this device on the port number of 8090 Then follow the steps below DDNS Settings Check the Enable DDNS box DDNS Service Provider Select your DDNS service provider from the drop down list Here in this example select dyndns org User Name Enter the DDNS user name you have registered with your as B Features A Configurations Tenda DDNS service provider Here in this example enter tenda 4 Password Enter the DDNS Password you h
69. s set to Obtain an IP Address Automatically If you disable this feature you have to manually configure the TCP IP settings for all PCs on your LAN to access the Internet Click Basic gt DHCP Server to enter the screen below Here you can change the DHCP IP address pool and lease time LAN Settings DHCP Server WAN Settings DHCP Server WAN Speed Start IP DNS Settings End IP MAC Clone Lease Time DHCP Server DHCP Client List Configuration Procedures M Enable 192 168 0 100 192 168 0 200 1 day Cancel Help The Dynamic Host Configuration Protocol DHCP is an automatic configuration protocol used on IP networks If you enable the built in DHCP server on the router it will automatically configure the TCP IP protocol settings for all PC s in the LAN including IP address subnet mask gateway and DNS Start IP Enter the starting IP address for the DHCP servers IP assignment End IP Enter the ending IP address for the DHCP servers IP assignment Lease Time The lease time is atime length thatthe IP address is assigned to each device before itis refreshed DHCP Server Enable Check uncheck the box to enable or disable the DHCP server feature Start IP End IP You can specify the starting and ending addresses of the IP address pool here These addresses should be part of the same IP address subnet as the device s LAN IP address 36 A Features A Configurations Te
70. see 2 5 MAC Clone Available only in Wireless Router Mode To configure DHCP server see 2 6 DHCP Server To assign static IP addresses and view LAN device information see 2 7 DHCP Client List Anote In the Universal Repeater Mode only the LAN Settings screen is available 2 1 LAN Settings Here you can configure the LAN IP address and subnet mask This IP address is to be used to access the device s settings through a Web browser Be sure to make a note of any changes you apply to this page Vip Default IP address and subnet mask are respectively 192 168 0 1 and 299 2959 255 0 If you change the LAN IP address of the device you have to open a new connection to the new IP address and log in again Also you have to set the default gateway addresses of all LAN PCs to this new IP address The device s LAN IP address and WAN IP address must be on different IP Ei Features Configurations Tenda segments If not it will not be able to access the Internet WAN Settings IP Address 192 16810 4 WAN Speed Subnet Mask 255 255 255 0 DNS Settings MAC Clone Save wl e Cancel DHCP Server DHCP Client List Configuration Procedures Change the IP address to the one you wish to use 192 168 10 1 Click Save to save your settings 2 2 WAN Seitings Help Use this section to configure device s LAN IP address and Subnet Mask The default IP address is 192 168 0 1 and the defau
71. switch System Mode Ge 3G 4G Priority Ethernet Priority Help Here you can view the WAN status LAN status wireless status and system status of the device Help 3G 4G Router Mode In this mode the router acquires Internet access through an activated 3G 4G USB modem which is attached to its USB port Wired WAN access is disabled Wireless Router Mode In this mode the router acquires Internet access through a wired WAN port 3G 4G access is disabled Universal Repeater Also known as Client plus AP Mode In this mode the router 4 Quick Internet Setup amp Wireless Security Setup Read the following and determine your Internet connection type Then follow the right setup wizard A If you access the Internet via a 3G 4G USB modem see 3G 4G Router o fi Quick Setup Tenda Mode B If your ISP provides you with a cable from the incoming Internet side but no ISP login account or IP information your ISP uses a DHCP connection See Wireless Router Mode DHCP C If your ISP provides you with a cable from the incoming Internet side and a PPPoE login account your ISP uses a PPPoE connection See Wireless Router Mode PPPoE D If you acquire Internet access from a remote AP on an existing network see Universal Repeater Mode E To learn about the Auto switch System Mode 3G 4G Priority and or Ethernet Priority see Auto switch System Mode amp Priority 3G 4G Router Mode Select 3G 4
72. ter e EE 7 EREECHEN DEE 7 9D Web LOSIN BEE 8 4 Quick Internet Setup amp Wireless Security Setup eege 9 AG Rouer EE 10 Witeless Ron r Mo DICTI EE 12 Wireless Router Mode PPPOE cece ccc ccc eee eee nent e eee e eects eee eens nee eee eneennee ees 13 Universal Repeater Ee 15 AULO S witch System Mode amp Priority eege Eege EE Ee NEE ge 17 LU Features amp CO Ol SU E icra care cteessinsacccascnawseetsracsaoce itera sannnncennsaaersetasacacacseaeseansnnnsees 19 ee EE 19 RE E 19 LAN SCAT EE 21 Wt GICs SS CAUUS nace cc cmetcacea acaeanns kocatessicucsnee seach soticananns cont padidcnauracenge uaeacenoescetannsiceasaanne 21 Dy CCCI EE ereechbar tee Se GE EE 23 2 1 LAN Settings E 23 EK ENEE 24 2 3 WAN Speed Available only in Wireless Router Moden 32 De JOINS SOUS EE 33 2 5 MAC Clone Available only in Wireless Router Mode ccc cece cece eee e eect ee enees 34 DO WTO SC E 36 Drak AO Cae Ce TG eebe a1 SNE CUI EE 40 PEDA ee 40 i COUN EE 41 E E e eh Ge EN EE 44 4 Advanced EE 47 wL DDNS S EE 47 E Eeer 50 Be WINE EE 51 4 4 Remote Web Management 52 4 5 Bandwidth Control Available only in AGo00t eee nent e eee eneeeeeee ees 53 4 6 Client Filter Available only in AGoo 0t nee e ee ee ene eens eeeneennee ees 55 e EE 59 Det Time RE EE 59 32 Firmware 1 POC E 61 Ster EENEG 62 Jet eStore de RE e DE EC EE 65 5 5 Change PAG SW O0 Gis echo nisadisesnuseee pied ne neoedene boresencaconseenp
73. usbionc beneseessenedeneaesasdernsetdona beoade 66 DCO E 67 Deh IRC EE 68 WE Er EE E 69 CO ie YO TEE 69 WN ee EE 69 Windows EE 71 2 Join Vout Wireless INCiw Ok E 74 NY TOS EE 74 WMO WS EE 13 AN EE 78 4 Remove Wireless Network from Your EE eege ee EE e EES 80 WIM O Wis EE 80 WY Td OWS OO EE 8 Product Overview 1 Package Contents Unpack the package Your box should contain the following items 3G 4G Wireless Router Ethernet Cable Power Adapter Install Guide Vv Vv V V Resource CD If any of the parts are incorrect missing or damaged contact your Tenda dealer Keep the carton including the original packing materials in case you need to return the product for repair 2 Getting to Know Your Device 2 1 What It Looks like I Product Overview Tenda 2 2 LED Wa Be Zen oe T DM e d Ke a I i Zei KI The device is receiving electric power Blinking System is starting up properly Blinking The device is functioning properly I Product Overview Tenda The WAN LAN WLAN interface is transmitting Blinking data WAN LAN WiFi The WAN LAN interface is connected correctly The WiFi radio is on The USB port is connected correctly This icon indicates no actual meaning It is only for decoration 2 3 Button amp Interface USB port for attaching a 3G 4G USB Modem Pressing this button for over 6 seconds resets the WPS Reset device to factory default settings or 1 3
74. uter Mode lf the Auto switch System Mode and 3G 4G Priority are selected system will prioritize the 3G 4G Router Mode when detecting the coexistence of an a fi Quick Setup Tenda Ethernet cable and a 3G 4G USB modem operate in the 3G 4G Router Mode when only detecting a 3G 4G USB modem toggle to the Wireless Router Mode when only detecting an Ethernet cable If the Auto switch System Mode and Ethernet Priority are selected system will prioritize the Wireless Router Mode when detecting the coexistence of an Ethernet cable and a 3G 4G USB modem toggle to the 3G 4G Router Mode when only detecting a 3G 4G USB modem operate in the Wireless Router Mode when only detecting an Ethernet cable as fi Quick Setup Tenda lll Features amp Configurations 1 Status Click Status to enter the Status screen WAN Status WAN Status in 3G 4G Router Mode Status WAN Status Help 3G 4G Traffic Statistics internet Connection Status Connected Here you can view the WAN status LAN status wireless WANIP 10 30 233 107 status and system status of the device SubnetMask 255 255 255 255 Gateway 10 0 0 1 Primary DNS Server 221 12 1 227 Secondary DNS Serer 221 12 33 227 Internet Connection Type 3G 4G Disconnect 3G 4G Traffic Statistics To view the 3G 4G traffic statistics click Status gt 3G 4G Traffic Statistics This screen is available only in the 3G 4G Router Mode P Features Con
75. your router remotely Note If the IP address is 0 0 0 0 it indicates that all WAN IP can access the web Zoe For better security configure a port number between 1025 and 65535 as the remote Web management interface do not use the number of any common service port 1 1024 Make sure your WAN IP address Internet IP address is a public IP address Private IP addresses are not routed on the Internet It is unsafe to make your router remotely accessible to all PCs on external network For the purpose of security we suggest that you only enter the IP address of the PC that is to be used to remotely manage your device Remote Web Management Application Example To access your device WAN IP address 102 33 66 88 at your home from the B Features A Configurations Tenda PC 218 88 93 33 at your office via the port number of 8090 follow the steps below Enable Check to enable the remote Web management feature Port Enter 8090 IP Address Specify the IP address for remote management Here in this example enter 218 88 93 33 Click Save to save your settings Advanced DDNS Settings Remote WEB Management Help Management feature allows from the Internet via a web IP Address 218 88 93 33 browser To use this feature Check the Enable Remote Web Management box and specify a Remote Management Port Port Remote admin port the port used to access the device from Internet or exte

Tenda 4G630 router

Contents

Download Pdf Manuals

Related Search

Related Contents