Liebherr GNP 1956 Premium NoFrost
Contents
1. gt When mounting the pressure plates make sure they snap into place properly Transfer the spring clamp Fig 8 20 Depress the latch nose and pull the spring clamp off over it Slide the spring clamp into place on the new hinge side until it clicks into place gt Pull the bearing pin Fig 8 21 out of the door bush and transfer it to the opposite side together with the washer The latch nose must point to the inner side of the door the notch to the outer side gt Hang the door on the bearing pin Fig 6 9 at the top gt Swing the door in at the bottom and insert the bearing pin Fig 8 27 into the turn hinge If necessary turn the bearing pin until it snaps into place Insert the securing screw Fig 4 7 at the bottom into the bearing pin and tighten it with 4 Nm If necessary align the door flush with the appliance housing using the two slots in the turn hinge To do so unscrew the middle screw A WARNING Risk of injury due to the door dropping out If the bearing parts are not screwed into place firmly enough the door may drop out This may lead to severe injuries What is more the door may not close and therefore the appliance may fail to cool properly gt Screw on the bearing brackets bearing pins tightly 4 Nm Check all of the screws and retighten if necessary Depending on model and options Putting into operation 4 4 Insertion into a row of kitchen units a2. power failure for some time the appliance is faulty The audible alarm is automatically silenced the alarm symbol Fig 3 4 goes out and the temperature display stops flashing when the temperature is sufficiently cold again If the alarm status persists see Malfunction Note Food may be spoilt if the temperature is not cold enough Check the quality of the food Do not consume spoiled food 5 4 1 Muting the temperature alarm The audible alarm can be muted When the temperature is sufficiently cold again the alarm function is active again Press alarm button Fig 3 9 gt The audible alarm is silenced 5 5 Freezing food The rating plate indicates the maximum quantity of fresh food you can freeze within 24 hours see Appliance at a glance under Freezing capacity kg 24h The maximum load of frozen food for the drawers is 25 kg each and for the shelves 35 kg each A CAUTION Risk of injury due to broken glass Bottles and cans containing drinks may burst when being frozen This applies particularly to sparkling drinks gt Do not freeze bottles and cans containing drinks In order that the food is rapidly frozen through to the core do not exceed the following quantities per pack Fruit vegetables up to 1 kg Meat up to 2 5 kg Pack the food in portions in freezer bags reusable plastic metal or aluminium containers 5 6 Thawing food at room temperature inamicrowave
3. 4 Fig 9 1 Stack cabinet 3 Kitchen cabinet 2 Appliance 4 Wall For appliances supplied with wall spacers the measurement increases by 35 mm see 4 2 The appliance can be inserted into a row of kitchen units To match the appliance Fig 9 2 to the height of the row of units a suitable stack cabinet Fig 9 7 can be fitted above the appli ance When installing with kitchen units max depth 580 mm the appliance can be positioned directly next to the kitchen cabinet Fig 9 3 The appliance will project by 34 mm at the sides and 50 mm in the centre of the appliance in relation to the kitchen cabinet front Important for the ventilation Atthe back of the stack cabinet there has to be a ventilation duct of at least 50 mm depth throughout the width of the stack cabinet The ventilation space under the ceiling has to be at least 300 cm the larger the ventilation space the more energy saving the appliance is in operation If the appliance is installed with the hinges next to a wall Fig 9 4 the distance between appliance and wall has to be at least 40 mm This corresponds to the projection of the handle when the door is open 4 5 Disposing of packaging A WARNING Danger of suffocation due to packing material and plastic film gt Do not allow children to play with packing material Control The packaging is made of recyclable materials corrugated board cardboard expanded poly
4. gt The demo mode is activated Please contact the after sales service see Maintenance The outer surfaces of the appliance are warm gt The heat of the refrigeration circuit is used to prevent condensate from forming This is normal The temperature is not cold enough The door of the appliance is not properly closed Close the door of the appliance Insufficient ventilation Clear ventilation grilles The ambient temperature is too high 12 Solution see 1 2 gt The appliance was opened too frequently or for too long Wait to see whether the appliance reaches the required temperature by itself If not please contact the after sales service see Maintenance Too much fresh food was placed inside without SuperFrost Solution see 5 8 Thetemperature is incorrectly set Set the temperature to a colder setting and check after 24 hours The appliance is too close to a source of heat stove heater etc Change the position of the appliance or the source of heat The interior light is not on The appliance is not switched on Switch on the appliance The door was open longer than 15 min The interior light automatically switches off if the door has been open for about 15 min When the interior illumination does not work but the temper ature display is lit the illuminant delivery with LED illumi nant is defective A WARNING Risk of inju
5. and manufactured for a long life span and reliable operation If a malfunction nonetheless occurs during operation check whether it is due to a handling error In this case you will have to be charged for the costs incurred even during the warranty period You may be able to rectify the following faults yourself Appliance does not work The appliance is not switched on Switch on the appliance The power plug is not properly inserted in the wall socket Check power plug gt The fuse of the wall socket is not in order p Check fuse 11 Decommissioning The compressor runs for a long time The compressor switches to a low speed when little cold is needed Although the running time is increased as a result energy is saved This is normal in energy saving models SuperFrost is activated gt The compressor runs for longer in order to rapidly cool the food This is normal A LED on the bottom rear of the appliance at the compressor flashes regularly every 15 seconds The inverter is equipped with a diagnostic LED gt The flashing is normal Excessive noise gt Due to the various speed steps speed regulated compressors can generate different running noises p The sound is normal A bubbling and gurgling noise gt This noise comes from the refrigerant flowing in the refriger ation circuit gt The sound is normal A quiet clicking noise gt The noise is
6. must be used to achieve the stated energy consumption These will extend the depth of the appliance by approx 35 mm The appliance is fully functional if the spacers are not used but does have a slightly higher energy consumption Putting into operation In the case of an appliance with enclosed wall spacers mount the wall spacers on the back of the appliance at the top left and right Dispose of packaging material see 4 5 Align the appliance so that it stands firmly and on a level by applying the accompanying spanner to the adjustable height feet A and using a spirit level Note Clean the appliance see 6 2 If the appliance is installed in a very damp environment condensate may form on the outside of the appliance Always see to good ventilation at the installation site 4 3 Changing over the door hinges You can change over the door hinges if necessary Ensure that the following tools are to hand OQ Torx 25 Q Torx 15 CL Open ended spanner size 6 U Screwdriver CL Open ended spanner included in supply package Q Second person for fitting work if needed A CAUTION Risk of injury if the door tips gt Take good hold of the door gt Set down the door carefully gt Unscrew the securing screw on the bottom right turn hinge gt Open the door Hold the door on the handle side and at the bottom and lift it gt The bearing pin Fig 4 27 should come out of the turn hinge
7. of heavy soiling use a little water or neutral cleaning agent A micro fibre cloth can be used optionally Clean items of equipment by hand with lukewarm water and a little washing up liquid After cleaning Wipe dry the appliance and items of equipment Connect the appliance and switch it on again Switch on SuperFrost see 5 8 When the temperature is sufficiently cold Put the food back inside 6 3 Changing the interior light Inside the appliance an LED light is included as standard for interior lighting If an incandescent lamp is used Q Use an incandescent light with a max 15 W and E14 fighting Q The type of current alternating current and voltage at the location where the appliance is set up must agree with the information on the type plate see Appliance at a glance If an LED light is used Q Only the manufacturer s original LED light may be used The light is available through Customer Service or specialist dealers see 6 4 A WARNING Risk of injury from LED light The light intensity of the LED lighting corresponds to laser class 1 1M If the cover is removed gt Do not look directly into the light at close quarters through optical lenses Doing so may damage your eyes A WARNING Fire hazard from the LED light If different LED lights are used there is a danger of overheating or fire gt Use the manufacturer s original LED light If the light is defective exchange
8. oven in a conventional or fan oven gt Remove only as much food as is required Use thawed food as quickly as possible gt Food once thawed should be re frozen only in exceptional cases 5 7 Setting the temperature The appliance is pre set for normal operation The temperature can be set between 14 C and 28 C the recommended temperature is 18 C gt Set temperature to be warmer press Up setting button Fig 3 7 until the temperature in the display flashes Release button gt Set temperature to be cooler press Down setting button Fig 3 2 until the temperature in the display flashes Release button gt The previous value is indicated in the temperature display To change the temperature in 1 C steps briefly press the button Or To change the temperature continuously hold down the button Depending on model and options Control gt The value is displayed flashing during the setting operation gt The actual temperature is displayed approx 5 seconds after the button is last pressed The temperature gradually adjusts to the new value 5 8 SuperFrost With this function you can freeze fresh food quickly through to the core The appliance operates with maximum refrigeration The noise of the refrigeration unit may be temporarily louder as a result In addition frozen food already in storage is given a cold reserve The food stays frozen longer as a result when you defrost
9. the appliance The maximum amount of fresh food which can be frozen in 24 h is indicated on the type plate under freezing capacity kg 24h This amount varies according to the model and climate rating You have to activate SuperFrost in good time depending on how much fresh food is to be frozen about 6 hours before placing the food inside in case of small amounts and about 24 hours in advance in case of the maximum amount of food to be frozen Wrap produce and spread it out as far as possible Do not allow produce to be frozen to touch produce that is already frozen to prevent the latter thawing You do not have to activate SuperFrost in the following cases when placing frozen food in the freezer when freezing up to approx 2 kg fresh food daily w 5 8 1 Freezing with SuperFrost Press SuperFrost button Fig 3 8 until the symbol is displayed Release button gt The freezing temperature drops the appliance operates with the maximum cooling capacity For a smaller quantity of produce to be frozen wait approx 6h Place wrapped produce in the deep bottom drawers For the maximum quantity of produce to be frozen wait approx 24 h Remove the deep bottom drawers and place produce directly on the bottom shelves gt SuperFrost is automatically deactivated Depending on the quantity placed inside after 30 h at the earliest 65 h at the latest gt The SuperFrost symbol Fig 3 5 extingu
10. Appliance at a glance Contents 1 Appliance at a glance uuursnnunennnnnnonnnnennnnnennnnnenn 2 1 1 Description of appliance and equipmert 2 1 2 Range of appliance use uusnsnneneenenenneenennnne nennen 2 1 TEONOnm ee ee 3 1 4 External dimensions of the appliance 3 1 5 Saving energy unneessesennnnnennnnnnnnnnnnnnnnnnnnnnnnnennnnnnnennnn 3 1 6 Insulation plate ce ceeccesecceeseeeseseeseeseeeesseeeneeees 3 1 7 HomeDialog ccc ceccceceseceeceseeeeeeenseeeenansereneeneees 3 1 8 OPT eea AEAEE 3 2 General safety information uuuusunnnnnnnennnn 4 3 Controls and CiSplayS cccscsseeeeeesseeeeeenseeeeeenees 5 3 1 Operating and control elements 5 3 2 Temperature display ccccccccccseccesseeeeeeeeesseeeesaees 5 4 Putting into operation uusnuunennannennnnnnnnnnnnnnnnnenn 5 4 1 Transporting the Appliance cccccceesseeeeeseeeeeeeees 5 4 2 Installing the ADPliANCE c ce eceeseeeeeeeeeeeeeeeeeeeeeees 5 4 3 Changing over the door NiNgGes cccseeceeeeseeeees 6 4 4 Insertion into a row of kitchen units u 7 4 5 Disposing of packagQing ceceeeeeeeeeeeeeeeeeeeeeeees 7 4 6 Connecting the appliance cccccceessseeeeesseeeeeees 8 4 7 Switching on the appliance ccccseseeeeeseeeeeeeeees 8 5 COIN hissed ee 8 5 1 Brightness of th
11. Fig 5 2 If the bearing pin Fig 4 27 does not come out press the pin out from underneath gt Swing door out at the bottom and remove it Fig 5 gt Unscrew the turn hinge Fig 5 2 gt Unscrew the bearing element Fig 5 3 transfer it to the opposite location hole of the turn hinge and screw it firmly into place gt Take the stopper Fig 5 4 out of the turn hinge and transfer it to the receiving hole on the opposite side of the turn hinge Carefully lift off the cover Fig 5 5 on the handle side gt Undo the screw Fig 5 6 and transfer it to the opposite side gt Put the cover Fig 5 5 back on Screw the turn hinge Fig 5 2 firmly into place on the new hinge side with 4 Nm possibly using a power screwdriver Fig 6 At the top use a screwdriver to unclip cover Fig 6 7 and cover Fig 6 8 at the front and remove by pulling out and down gt Unscrew the bearing pin Fig 6 9 and screw it firmly into place on the opposite side with 4 Nm gt Refit the cover Fig 6 7 on the side of the bearing pin insert at the back snap in at the front Fit the cover Fig 6 8 on the opposite side insert at the back snap in at the front Depending on model and options Fig 7 Lift the stopper Fig 7 72 out of the door bearing bush and transfer it Detach door handle stoppers Fig 7 70 and pressure plates Fig 7 77 and transfer to the opposite side
12. ON Risk of injury and danger of damage as a result of incorrect transport Transport the appliance in a packed condition Transport the appliance upright Do not transport the appliance without assistance 4 2 Installing the appliance A WARNING Fire hazard due to dampness If live parts or the mains lead become damp this may cause short circuits The appliance is designed for use in enclosed areas Do not Operate the appliance outdoors or in areas where it is exposed to splash water or damp conditions Depending on model and options Controls and displays A WARNING Risk of fire due to short circuit If the mains cable connector of the appliance or of another appliance touch the rear of the appliance the mains cable connector may be damaged by the appliance vibrations leading to a short circuit Stand the appliance so that it is not touched by connectors or main cables gt Do not plug the appliance or any others into sockets located near the rear of the appliance A WARNING Fire hazard due to refrigerant The refrigerant R 600a is environmentally friendly but flam mable Escaping refrigerant may ignite gt Do not damage the piping of the refrigeration circuit A WARNING Fire hazard and danger of damage Do not place appliances emitting heat e g microwaves toasters etc on the appliance A WARNING Blocked ventilation openings pose a risk of fire and damage Alway
13. ance Cleaning and user maintenance must not be carried out by children without supervision When disconnecting the appliance from the supply always take hold of the plug Do not pull the cable In the event of a fault pull out the mains plug or deactivate the fuse Do not damage the mains power cable Do not operate the appliance with a defective mains power cable Have any repairs to or intervention in the appliance and any change of the mains power cable carried out by the customer service only or by other specialised personnel trained for the purpose Only assemble connect and dispose of the appliance according to the instructions Please keep these instructions in a safe place and pass them on to any subsequent owners Special purpose lamps incandescent lamps LEDs fluorescent tubes in the appliance serve to illuminate the appliance interior and are not suited for room illumination Fire hazard The refrigerant R 600a is environmentally friendly but flammable Escaping refrigerant may ignite Do not damage the refrigerant circuit pipes e Do not allow naked flames or ignition sources to enter the appliance Do not use any electrical appliances in the interior e g steam cleaners heaters ice cream maker etc If refrigerant escapes remove any naked flames or sources of ignition from the leakage area Ventilate the room well Notify the after sales service Do not store explosives
14. cines blood plasma laboratory preparations or similar substances and products covered by the 2007 47 EC Medical Devices Directive Misuse of the appliance can result in the stored prod ucts suffering harm or perishing Furthermore Depending on model and options the appliance is not suitable for operation in potentially explosive atmospheres The appliance is set to operate within specific ambient temperature limits according to its climate rating The correct climate rating for your appliance is indicated on the type plate Note Compliance with the ambient temperatures indicated is required otherwise the cooling performance is reduced Climate for ambient temperatures rating SN N up to 32 C ST up to 38 C T up to 43 C The appliance will function properly in ambient temperatures of down to 5 C 1 3 Conformity The refrigerant circuit is tested for leakage The appliance complies with the relevant safety regulations and EC Directives 2006 95 EC 2004 108 EC 2009 125 EC and 2010 30 EU Note for test institutions Tests are to be carried out according to the applicable standards and guidelines Preparation and testing of the appliances must be carried out taking the manufacturer s loading plans and the notes in the operating manual into account 1 4 External dimensions of the appli ance Fig 2 H mm GNP 1956 GNP 2356 1250 1447 For appliances
15. e right to make design equipment and technical modifications To get to know all the benefits of your new appliance please read the information contained in these instructions carefully The instructions apply to several models Differences may occur Text relating only to specific appliances is marked with an asterisk Instructions for action are marked with a the results of action are marked with a gt 1 Appliance at a glance 1 1 Description of appliance and equip ment Note Shelves drawers and baskets are arranged for optimum energy efficiency on delivery N Fig 1 1 Transport grips at back 2 Operating and control elements 3 LED interior light 4 NoFrost 5 Drawer for herbs and berries 7 Type plate 8 Drawers 9 Information system 10 VarioSpace 11 Adjustable feet transport grips at front transport castors at back 6 Cold storage accumu lator 1 2 Range of appliance use The appliance is suitable solely for cooling food in a domestic environment or similar This includes use in for example in staff kitchenettes bed and breakfast estab lishments by guests in country homes hotels motels and other forms of accommodation in catering and similar services in the whole sale trade Use the appliance solely as is customary within a domestic environment All other types of use are inadmissible The appliance is not suitable for storing and cooling medi
16. e temperature display 8 5 2 IMIG PRO OTM G eis cesawetninwenteatarlnacectenmnancotivedesvoecemeattc 8 Do D 910 a2 2 M aa eee en eee tee eer creer renee ene tee en cree 8 5 4 Temperature alarim ccccccccccsssececsseeesseeeeseeeeseees 8 5 5 Freezing 1000 9 56 Thawing T000 ne ureee ea 9 5 7 Setting the temperature u4s4uunnnnn nennen naar 9 58 SUBEIEIOSE nennen 9 59 DAWES eines nee ee pinsin is 9 5 10 SNENOS esise s 10 5 11 Vallospateksinene e aa iaaa 10 5 12 Information system uessnenseeennsnnnennennnnn nennen nn 10 5 13 Drawer for herbs and berries 4400444 een 10 5 14 Cold storage accumulators us 440R ernennen 10 6 Ma ntenance nn 10 6 1 Defrosting with NOFTOSt ccccsseeeeeeeeeeeeeeeeeeees 10 6 2 Cleaning the appliance cccccsssseeeeesseeeeeseeeeees 10 6 3 Changing the interior light cccccssseeeeeeeeeeeeeees 11 6 4 Customer SEFVICE ccccccsseeeeceeseeeeseueeeeeeseneeeeenees 11 7 MAONO O sssrinin 11 8 Decommissioning urssnuerennnnnennnnnennnnnennnnnennnnen 12 8 1 Switching off the appliance 44usne nen 12 8 2 Taking the appliance out of service 12 9 Disposing of the appliance uuusnnunnnennnnnnnnnnnnn 12 The manufacturer works constantly on the further development of all the types and models Therefore please understand that we have to reserve th
17. ere bodily injury WARNING _ identifies a dangerous situation which if not obviated may result in death or severe bodily injury CAUTION identifies a dangerous situation which if not obviated may result in minor or medium bodily injury NOTICE identifies a dangerous situation which if not obviated may result in damage to property Note identifies useful information and tips Depending on model and options 3 Controls and displays 3 1 Operating and control elements ia xe N y 1 x A Lp Down er On Off SuperFrost Alarm D Fig 3 1 Up setting button 2 Down setting button 3 Menu symbol 4 Alarm symbol 5 SuperFrost symbol 6 Temperature display 7 On Off button 8 SuperFrost button 9 Alarm button 10 Power failure symbol 11 Child proofing symbol 12 HomeDialog symbol 3 2 Temperature display The following are displayed in normal operation the warmest freezing temperature The temperature display flashes the temperature setting is being changed after switch on the temperature is not yet cold enough the temperature has risen several degrees Dashes flash in the display the freezer temperature is above 0 C The following displays indicate malfunction Possible causes and corrective action see Malfunction FOtoFS The power failure symbol I flashes 4 Putting into operation 4 1 Transporting the appliance A CAUTI
18. es on the display gt The menu symbol Fig 3 3 shines Briefly press the SuperFrost button Fig 3 8 to confirm When et is indicated in the display Tto activate the child lock briefly press the C l SuperFrost button Fig 3 8 gt The child lock symbol Fig 3 11 shines c flashes in the display When cd is indicated in the display to deactivate the child lock briefly press the SuperFrost button Fig 3 8 gt The child lock symbol Fig 3 11 goes out c flashes in the display To deactivate the set up mode press On Off button Fig 3 7 Or Wait for 5 minutes gt The temperature is indicated again in the temperature display 5 3 Door alarm If the door is open for longer than 60 seconds the audible warning will sound The audible alarm is automatically silenced when the door is closed 5 3 1 Muting the door alarm The audible alarm can be muted when the door is open The sound switch off function is active as long as the door is left open Press alarm button Fig 3 9 gt The door alarm is silenced 5 4 Temperature alarm The audible alarm sounds if the freezer temperature is not cold enough The temperature display and the alarm symbol Fig 3 4 flash at the same time The cause of the temperature being too high may be Depending on model and options warm fresh food was placed inside too much warm ambient air flowed in when rearranging and removing food
19. garien www liebherr com
20. ggressive scouring sand chloride chemical or acid based cleaning agents gt Do not use chemical solvents gt Do not damage or remove the type plate on the inside of the appliance It is important for the customer service Do not pull off bend or damage cables or other compo nents gt Do not allow any cleaning water to enter the drain channel ventilation grille or electrical parts Please use soft cleaning cloths and a universal pH neutral cleaning agent Please use cleaning and care products suitable for contact with foodstuffs in the appliance interior Empty appliance Pull out the power plug Clean plastic outer and inner surfaces with lukewarm water and a little washing up liquid Depending on model and options NOTICE The stainless steel doors are finished with a high quality surface coating and must not be treated with the enclosed care product as otherwise the surface coating will be damaged 27 Please only use a soft clean cloth to wipe the coated door surfaces In the case of heavy soiling use a little water or neutral cleaning agent A micro fibre cloth can be used optionally When soiled clean stainless steel side walls with a commercially available stainless steel cleaning agent Then apply the enclosed stainless steel care product evenly in the direction of polishing Use only a soft clean cloth to wipe side walls and door surfaces with a paint finish In the case
21. ishes once freezing is completed Place produce in the drawers and push the latter back in again gt The appliance continues to operate in the energy saving normal mode 5 9 Drawers Note The energy consumption increases and the cooling perform ance decreases if there is insufficient ventilation For appliances with NoFrost gt Leave the bottom drawer in the appliance Always keep the air slits of the fan free at the rear wall Maintenance To store frozen food directly on the shelves pull the drawer forwards and lift it out 5 10 Shelves gt To remove the shelf lift up at the front and pull out To put the shelf back simply push in as far as it will go 5 11 VarioSpace Apart from being able to remove the drawers you can also remove the shelves creating space for large items of frozen food Poultry meat large pieces of game and high bakery products can be frozen in one piece and prepared gt The maximum load of frozen food for the drawers is 25 kg each and for the shelves 35 kg each Fig 10 1 Ready made meals ice 4 Sausages bread cream 2 Pork fish 3 Fruit vegetables 5 Game mushrooms 6 Poultry beef veal 5 13 Drawer for herbs and berries In the drawer for herbs and berries you can freeze berries herbs vegetables and other small items of food without them sticking together Items being frozen will largely retain their shape and it will be easier
22. it as follows Depending on model and options Malfunction Fig 11 Switch off the appliance Pull out the power plug or switch off the fuse gt Exchange the light under the control panel according to illus tration 6 4 Customer service First check whether you can correct the fault yourself by refer ence to the list see Malfunction If this is not the case please contact the customer service whose address is given in the enclosed customer service list A WARNING Risk of injury if repair work is not carried out professionally gt Have any repairs and action not expressly specified on the appliance and mains cable carried out by service personnel only see Maintenance gt Read the appliance designation Fig 12 1 service No Fig 12 2 and serial No Fig 72 3 off the type plate located inside the appliance on the left hand side UL T BEER index EEI EEL Samice No Sevko TEE H E T a Bo a D Fig 12 Notify the customer service specifying the fault appliance designation Fig 12 7 service No Fig 12 2 and serial No Fig 12 3 gt This will help us to provide you with a faster and more accu rate service Keep the appliance closed until the customer service arrives gt The food will stay cool longer Pull out the mains plug not by pulling the connecting cable or switch off the fuse 7 Malfunction Your appliance is designed
23. og system can be used to network a number of Liebherr appliances situated for example in the basement with a main appliance sited for example in the kitchen and control them via the latter You will find more information on the benefits requirements and principle of operation on the internet at www liebherr com 1 8 SmartGrid Depending on model and options your J appliance is prepared for the advanced SmartGrid technology SmartGrid is a future option for reducing household electricity costs via an intelligent meter supplied by the energy provider In the event of surplus energy being generated for instance by regenerative sources households are supplied with low cost electricity SmartGrid ready upright freezers are prepared for this future technology With an appropriate additional module you will be in a position to optimise your electricity costs For more information about the benefits requirements and operating principle visit the homepage of your energy provider and www liebherr com General safety information 2 General safety information Danger for the user This appliance can be used by children of 8 years old and over and also by persons with restricted physical sensory or mental capacity or lack of experience and knowl edge if they are supervised or have been instructed on safe use of the appliance and understand the resulting risks Children must not be allowed to play with the appli
24. or sprays using combustible propellants such as butane propane pentane etc in the appliance To identify these spray cans look for the list of contents printed on the can or a flame symbol Gases possibly escaping may ignite due to electrical components Keep burning candles lamps and other items with naked flames away from the appliance so that they do not set the appliance on fire Please be sure to store alcoholic drinks or other packaging containing alcohol in tightly closed containers Any alcohol that leaks out may be ignited by electrical components Danger of tipping and falling Do not misuse the plinth drawers doors etc as a step or for support This applies particu larly to children Danger of food poisoning Do not consume food which has been stored too long Danger of frostbite numbness and pain Avoid lasting skin contact with cold surfaces or refrigerated frozen food or take protective steps e g wear gloves Do not consume ice cream water ice or ice cubes immediately and do not consume them too cold Danger of injury and damage Hot steam can lead to injury Do not use elec trical heating or steam cleaning equipment open flames or defrosting sprays to defrost Do not use sharp implements to remove the ice Please observe the specific information in the other sections DANGER identifies a situation involving direct danger which if not obviated may result in death or sev
25. produced whenever the refrigeration unit motor automatically switches on or off gt The sound is normal A hum It is briefly a little louder when the refrigeration unit the motor switches on gt The refrigeration increases automatically when the Super Frost function is activated fresh food has just been placed in the appliance or the door has been left open for a while gt The sound is normal The ambient temperature is too high Solution see 1 2 Vibratory noise The appliance is not fixed to the ground The running of the cooling unit therefore makes objects and adjacent furniture vibrate Adjust appliance via the height adjustable feet gt Move bottles and containers apart The temperature display indicates F to F93 There is a fault gt Please contact the after sales service see Maintenance Power failure flashes in the temperature display Ir The highest temperature reached during power failure is indi cated in the temperature display The freezer temperature rose too high over the last hours or days due to a power failure or power interruption When the power interruption is over the appliance will continue to operate in the last temperature setting To cancel the display of the warmest temperature press alarm button Fig 3 9 Check the quality of the food Do not consume spoiled food Do not re freeze thawed food DEMO shines in the temperature display
26. ry from LED light The light intensity of the LED lighting corresponds to laser class 1 1M If the cover is removed gt Do not look directly into the light at close quarters through optical lenses Doing so may damage your eyes v vy Change the lighting see Maintenance 8 Decommissioning 8 1 Switching off the appliance Press the On Off button Fig 3 7 until the display goes dark Release button gt If the appliance cannot be switched off the child lock function is active see 5 2 8 2 Taking the appliance out of service Empty the appliance Pull out the power plug Clean the appliance see 6 2 Leave the door open to prevent odour 9 Disposing of the appliance The appliance contains some reusable materials and should be disposed of properly not simply with unsorted household refuse Appliances which are no longer needed must be disposed of in a professional and appropriate way in accordance with the current local regulations and laws When disposing of the appliance ensure that the refrigeration circuit is not damaged to prevent uncontrolled escape of the refrigerant it contains data on type plate and oil Disable the appliance Pull out the plug gt Cut through the connecting cable Depending on model and options Disposing of the appliance Depending on model and options 13 Liebherr Hausger te Marica EOOD 4202 Radinovo Bezirk Plovdiv Bul
27. s keep the ventilation openings clear Always ensure that the appliance is properly ventilated NOTICE Risk of damage due to condensate Do not install the appliance directly alongside a further refrigerator freezer L In the event that the appliance is damaged contact the supplier immediately before connecting to the mains U The floor at the site must be flat and level Q Do not install the appliance in a location where it is exposed to direct radiation of the sun next to a cooker heater and similar Q The ideal installation site is a dry well ventilated room Q Always stand the appliance backed directly to the wall using the enclosed wall spacers see below Q The appliance may be moved only when it is empty L Do not install the appliance without assistance Q Standard EN 378 specifies that the room in which you install your appliance must have a volume of 1 m per 8 g of R 600a refrigerant used in the appliance If the room in which the appliance is installed is too small a flammable gas air mixture may form in the event of a leakage in the refrigera tion circuit The quantity of refrigerant used in your appliance is indicated on the type plate on the inside of the appliance gt Detach the connecting cable from the rear of the appliance removing the cable holder at the same time because other wise there will be vibratory noise gt Remove all transit supports The spacers supplied with some appliances
28. styrene parts polythene bags and sheets polypropylene straps nailed wooden frame with polyethylene panel Take the packaging material to an official collecting point oN 4 6 Connecting the appliance NOTICE Risk of damage to the electronic control system gt Do not use stand alone inverters conversion of d c to a c three phase or energy saving plugs A WARNING Fire and overheating hazard Do not use extension cables or multiple socket outlets The type of current alternating current and voltage at the installation site have to conform with the data on the type plate see Appliance at a glance The socket must be properly earthed and fused The tripping current for the fuse must be between 10 A and 16 A The socket must be easily accessible so that the appliance can be quickly disconnected from the supply in an emergency It must be outside the area of the rear of the appliance Check the electrical connection Plug in the power plug 4 7 Switching on the appliance Switch on the appliance approx 2 hours before adding frozen food for the first time Do not load food to be frozen before the tempera ture display reads 18 C Press On Off button Fig 3 7 gt The temperature display and the alarm symbol flash until the temperature is sufficiently low If the temperature is above O C dashes flash If it is below the current temperature flashes gt The interior light is on
29. supplied with wall spacers the measurement increases by 35 mm see 4 2 Depending on model and options Appliance at a glance 1 5 Saving energy Always ensure good ventilation Do not cover ventilation openings or grille Donot place appliance in areas of direct sunlight or next to a stove heater or similar object The energy consumption depends on the installation condi tions e g the ambient temperature see 1 2 Keep the time the appliance is open to a minimum The lower the temperature setting the higher the power consumption Store food logically see Appliance at a glance Ensure that all food is well packed and covered for storage This will prevent frost from forming First cool warm food to room temperature before storing it Accumulated dust increases the energy F consumption Once a year dust the refrigerating unit together with the metal grille of the heat exchanger at the back of the appliance 1 6 Insulation plate The insulation plate for part load operation is available as an accessory from specialist dealers If you do not store much food in the appli ance you can reduce the power consump tion by as much as 50 by using the insu lation plate Up to 5 drawers can be de energised depending on model At least 3 drawers are necessary for cooling More information accompanies the insulation plate 1 7 HomeDialog Depending on model and options the Home Dial
30. to remove exactly the right quantity later on 5 13 1 Using the special drawer for herbs and berries Spread the items out loosely in the special drawer for herbs and berries Allow the food to freeze through for 10 to 12 h Transfer the frozen food to freezer bags or containers Store freezer bags or containers in a drawer To thaw the items spead them out loosely again 5 14 Cold storage accumulators The cold storage accumulators prevent the temperature from rising too fast in the event of power failure 10 5 14 1 Using cold storage accumulators Place the cold storage accu mulators in the special drawer for herbs and berries to save space Place the frozen cold storage accumulators on the frozen food in the upper front area of the freezer compartment 6 Maintenance 6 1 Defrosting with NoFrost The NoFrost system automatically defrosts the appliance The moisture condenses on the evaporator is periodically defrosted and evaporates gt The appliance does not have to be manually defrosted 6 2 Cleaning the appliance A WARNING Risk of injury and damage as a result of hot steam Hot steam can lead to burns and can damage the surfaces gt Do not use any steam cleaners NOTICE Incorrect cleaning damages the appliance gt Do not use cleaning agents in concentrated form gt Do not use any scouring or abrasive sponges or steel wool gt Please do not use any a
31. when the door is open gt If DEMO is displayed demo mode is activated Please contact the after sales service 5 Control 5 1 Brightness of the temperature display You can adjust the brightness of the temperature display to the light conditions of the room in which the appliance is installed 5 1 1 Adjusting the brightness The brightness is adjustable between h no illumination and hS maximum luminosity To activate setting mode press the SuperFrost button Fig 3 8 for approx 6 seconds gt The display indicates c gt The menu symbol Fig 3 3 shines Using the Up setting button Fig 3 7 or Down setting button Fig 3 2 select h gt To confirm briefly press the SuperFrost button Fig 3 8 To make the display brighter press Up button Fig 3 1 6 To make the display darker press Down button Fig 3 2 To confirm press SuperFrost button Fig 3 8 gt The brightness is adjusted to the new value gt To deactivate the set up mode press On Off button Fig 3 7 Or Wait for 5 minutes gt gt The temperature is indicated again in the temperature display 5 2 Child proofing The child proofing function enables you to make sure that the appliance is not inadvertently switched off by playing children FO 5 2 1 Setting the child lock function To activate setting mode press the SuperFrost button Fig 3 8 for approx 6 seconds gt c flash
Download Pdf Manuals
Related Search