Gamber-Johnson 7170-0125 mounting kit
Contents
1. Armrest Printer 24 Adjustment 25 20 x 50 Button Head Screws Insert 4 25 20 x 75 Carriage Bolts from inside of File Box Fig 3 Vertical Surface Mount 4 25 Flat Washers 4 25 20 Nylok Nuts The Vertical Surface Mount is attached to the end of the File Box 4 25 20 x 75 Carriage Bolts are inserted from the inside of the File Box and 4 Flat Washers and 4 Nylok Nuts installed on the outside The Armrest or Armrest Printer is inserted and secured in position by tightening the 3 8 bolt See Fig 3 3 of 4 INSTALLATION INSTRUCTIONS Product Date Form Faceplates 02 23 01 INST3 ASSEMBLING MCS FACEPLATES Refer to figure 1 DUAL LOCK FASTENER 1 Check that the following pieces are present Dual lock fastener supplied w console box 1 faceplate vertical offset 1 faceplate top bracket 1 flat washer 6 1 6 32 nut 2 For each faceplate slide the faceplate vertical offset item 1 on the stud in faceplate top bracket item 2 Add flat washer item 3 and hex nut item 4 Remove the extra strips of dual lock fastener pressed onto each console box under holddown rails cut to same length as D 312 each faceplate remove protective film covering the adhesive strip and apply to top bracket as shown 3 If the faceplates are being mounted in an older style MCS Console Box those with threaded inserts on the top surface of the side panels holddown screws passing th2. 2 A of 4
3. that the location chosen does not interfere with the proper operation of or cause damage to wiring fuel or hydraulic lines the exhaust system or drive train components and vehicle controls like gear shift lever airbag sensors or airbag deployment zone Using the Console and File Box as templates mark the mounting hole location on the vehicle floor Drill mounting holes thru vehicle floor 25 20 grade 5 bolts flat washers lock washers and hex nuts are recommended 2 f drilling into the vehicle floor is not possible the Console and File Box may also be attached to a Gamber Johnson MCS Long or Short Top Plate amp Vehicle Specific Leg kit Check with Gamber Johnson if a Vehicle Leg kit and Top Plate are available for your application Leg kits are typically installed by removing one or two of the bolts securing the driver and passenger seats inserting leg kit between seat bracket and vehicle floor reinstalling the seat bolts Specific instructions are supplied with each leg kit The Console and File Box are then bolted to the Top Plate using 25 20 x 1 00 Carriage Bolts 25 Lock Washers 25 20 Hex Nuts 2 of 4 Install the control heads accessories and blank panels into the console box Assemble faceplates to control heads as described in instruction sheet INST 3 see page 4 Electrically connect the equipment at this time allowing extra wire length for servicing the equipment File Box Console Box Armrest or
4. INSTALLATION INSTRUCTIONS Product Revision Form Work Truck Console w File Box Rev A INST 587 7170 0125 Work Truck Console w File Box and Armrest 7170 0164 Work Truck Console w File Box and Armrest Printer Printing Spec PS 001 The Work Truck Console w File Box Kits provide lockable storage for supplies and equipment A cupholder radios and control heads can be mounted in the Console box Letter size hanging folders can be stored in the File Box Carrying cutouts on sides aid in moving and installing The Workstation weighs approximatly 50 Ibs use caution when moving and installing The units are typically installed between the driver and passenger seats with Console Box installed toward the front of the vehicle and the File Box openning for the drivers access This allows the Vertical Surface Mount and Armrest or Armrest Printer to mounted on the end of the File Box See Fig amp Fig 2 Armrest 7170 0125 7170 0164 Fig Fig 2 Product Mounting Disclaimer Gamber Johnson is not liable under any theory of contract or tort hw for any loss damage personal injury special incidental or consequential damages for personal injury or other damage of any nature arising directly or indirectly asa result of the improper installation or use of its products in vehicle or any other application In order to safely install and use Gamber Johnson products full consideration of vehicle occupants vehicle systems i e the location of f
5. rough slots in existing face plates or blank panels DO NOT attach the strip of dual lock fastener on each faceplate as described above When installing faceplates into these MCS Console Boxes mark any that cover the threaded inserts and drill a 312 diameter clearance hole as shown in Figure 1 ASSEMBLING MCS FACEPLATES TO CONTROL HEADS AND I NSTALLING IN MCS CONSOLE BOXES Refer to figures VASE 1 Install the faceplates on each control head as shown in figure 2 Adjust the faceplates so the mounting holes in the sides of the control head line up in the slots of the faceplate vertical offsets and so the desired amount of the control head will extend from the console Make sure to allow enough room underneath for any connectors that may be required Test the fit of each control head the tallest heads may need to be installed near the higher end of the console 2 Arrange the control heads in the console box as desired Blank panels of various sizes have been provided to act as spacers between each control head if needed Secure in place by attaching a piece of dual lock fastener to each end of the blank panel and then pressing the strips of dual lock fastener on the faceplates blank panels and console box together 3 Attach the MCS Console Box holddowns to the sides of the console box and over faceplates with 6 10 32 x 38 Phillips head machine screws FACE PLATES one HARDWARE SUPPLIED BY CUSTOMER BLANK PANELS EQUIPMENT FIGURE
6. uel lines brakes lines electrical drive train or other systems air bags and other safety equipment is required Gamber Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications and recommendations Gamber Johnson product instruction sheets or workmanship standards as endorsed through the Gamber Johnson Certified Installer Program copyright 2012 Gamber Johnson LLC If you need assistance or have questions call Gamber Johnson at 1 800 456 6868 of 4 There are two ways to install and attach the Console and File Box Kits to the vehicle floor The first requires drilling holes into the vehicle floor the second uses the existing seat bolts The Console and File boxes can be attached directly to the vehicle floor Mounting holes are provided in the bottom of each Customer to supply nescessary hardware The height and angle of the Console Box can be adjusted if needed to allow 2 4 of vertical adjustment or to compensate for an uneven vehicle floor by removing the 4 25 20 x 50 Button Head Screws from the sides of the Console Box repositioning the slots on the Console Box with the threaded inserts on the Console Base and reinstalling the Button Head Screws See Fig 3 Position the Workstation in vehicle Depending on vehicle used and desired location a center console or seat section may need to be removed Check
Download Pdf Manuals
Related Search