Wi-Ex zBoost SOHO
Contents
1. If the antennas are too close together the light on the Base Unit will flash red indicating a problem see the Light Indicators section Page 12 To capture the best signal place the Signal Antenna as high as possible and position it vertically keeping it at it at least 2 feet away from any metal The location of the Signal Antenna should be at least 15 feet higher than the Base Unit Antenna If this is not possible maximizing the horizontal separation between the 2 antennas is advised See page 6 Setting Up Your zBoost Product for additional information Antenna Bracket Assembly IMPORTANT Incorrectly mounting the Signal Antenna to the 7 mounting bracket see figure A will impede performance Ensure that the Signal Antenna is properly positioned in the mounting bracket as f pictured below To mount antenna to a pole Attach bottom of antenna to pole bracket Figure A as pictured Use U Bolt to secure bracket to pole and fasten To mount antenna to a flat surface Attach bottom of antenna to pole bracket as pictured Secure bracket to desired surface using provided screws Use of the Saddle and U Bolt are not necessary for this option Pole Bracket Saddle ZBOOST YX545 SOHO USER GUIDE Additional Cable Requirements If the distance between the Signal Antenna and the Base Unit exceeds 50 feet extension cables are available on our website or at many home improvement and electronic stores The included cable is RG59 m2. not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If the equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This transmitter must not be co located or operating in conjunction with any other antenna or transmitter In accordance with FCC requirements of human exposure to radiofrequency fields the radiating element antenna shall be installed such that a minimum separation distance of 20cm 8in is maintained from all persons Industry Canada Regulations IC ID 5544A YX545PCSCEL This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept a
3. optimize performance If you find the increased signal coverage is acceptable however no additional adjustments are needed See Light Indicator section Page 12 for more information Figure A Pole Bracket wn D 2 D oe oe os m m m ZBOOST YX545 SOHO USER GUIDE Positioning the Base Unit For the widest possible signal area it is recommended that you position the zBoost YX545 SOHO Base Unit near the middle of a room or mount it on an interior wall This Base Unit uses an omni directional antenna that delivers signal in a circular pattern around the antenna If you decide to position the Base Unit on or near an outside wall we recommend purchasing a Directional Base Unit Antenna Page iv to focus the signal in the direction of your choice The Base Unit can be mounted either directly on a wall or placed on a flat surface e g a bookshelf desk end table etc The Base Unit performs best when located at least 4 feet above the floor or approximately the height of a cell phone when it is typically in use avoid placing the Base Unit on the floor For best results avoid placing the Base Unit antenna within 2 feet of other cords metal objects or other wireless devices such as wireless routers or wireless access points Confirm That Your zBoost is Working Properly Perform the following steps to confirm that the unit is now working properly 1 Unplug the Base Unit power cord 2 Turn on your cell ph
4. zBoost YX520 I Dual band works on 900MHz and 1800Mhz We also sell zBoost ONE YX400 U for UMTS HSPA devices on the 2100MHz Frequency a frequency used for voice and data overseas Why isn t my cell phone indicating more signal with more bars You may not always observe more bars that gain on your signal meter because of the signal spreading out from the antenna If your phone has a dB meter 3dB is a significant increase of 2x 6dB is 4x and 10dB is 10x On a four bar phone one bar equals about 10dB The increase in signal you will see depends upon e The level of signal at the Signal antenna outdoor The care of the antenna placement two feet away from metal adequate antenna separation 15 feet recommended The signal already present inside related to building losses The distance of your phone device from the Base Unit signal spreads or diminishes rapidly with dis tance There are usually several cell phones in use at one time in my home will your product boost all of our signals simultaneously The zBoost YX545 SOHO is designed to cover multiple signals simultaneously and will allow multiple users to operate at the same time Does the zBoost work if you have no bars y No if no signal is present outdoors zBoost producs will not work for you Also keep in mind if your best signal is 1 bar at the Signal Antenna your coverage will be limited to a small room You could improve that with an upgrade
5. 1 Location of the Cell Phone Tower in Relation to Your Home Office While cell phone providers have tried to place cell phone towers to provide the best overall coverage local ordinances and terrain features can impose restrictions on where these towers can be placed thus limiting the signal strength available at your location 2 Obstructions Caused by Buildings Terrain and Trees Cell phone signals can be completely blocked or reflected by buildings walls trees hills and other terrain features resulting in low signal strength 3 Energy Efficient Windows These new windows can also affect signal penetration into the house Yul ZBOOST YX545 SOHO USER GUIDE Preparing to Set Up Your zBoost Product Tools Neede The following tools are needed to set up zBoost 2 Philips screwdriver Cellular phone operating in the band supported by your zBoost unit Drill may be required for outdoor or attic antenna placement Check for Signal Strength Before placing a zBoost in your home make sure that you can place calls on the outside of your home in the attic at roof level or wherever you plan to place the signal antenna zBoost can only bring signal into your home when signal reaches the Signal Antenna If there is no signal the zBoost will not work for you Using your cell phone place a call from an outdoor location to confirm that enough signal is present to complete the call Ifa weak signal is availab
6. 871 1612 To get warranty service Warranty service will be provided by Wi Ex If you believe you need service for your unit contact Wi Ex at 1 800 871 1612 or support wi ex com A representative will go through a diagnostic checklist with you If it is determined that the product needs to be returned for service or exchanged you will receive a return merchandise authorization RMA number The representative will give you complete shipping details Do not return products to Wi Ex without a Return Authorization Number RMA To get out of warranty service To obtain out of warranty service contact Wi Ex at 1 800 871 1612 or support wi ex com for information on the possibility of any costs for repair or replacement of out of warranty products Reminder Record the model and serial number found on the product below Model Serial Purchase Date
7. O O AONT 6 Better Performance ee st enaa ia pia E VS TANE IETT AEN ea AE TEE RETRETAS 7 Best Performance Positioning the Base Unit Confirm That Your zBoost is Working Properly c scsssessessesesesessesesescsesessescseseescsescessseaesneseseaneneneas 10 Improving Your Coverage Area sssssssssssssssssssnsscscscsssssnsacscscscsssnssencacacecessnsseseseaeesensasaescacecensneacacscesenees zBoost Base Unit Light Indicators YX545 SOHO Technical Specifications ssccsssssssssrerscssssssssseseessssssssssssssssssssssessceesssssssssessesecsesssesseeeres 13 Frequently Asked Questions usisero eieaa E E E aa EEE E E Ea EOE ESE E EE 14 ZBoost Warranty Information cssscsssssssssssssssssscsssssscssssssssssssssssssssssssessassssesssssssssassssessssesesseseees 15 amp 16 1 ZBOOST YX545 SOHO USER GUIDE Overview Thank you for choosing zBoost You will now be able to use your cell phone INSIDE your home or office Gone are the days when you had to go to the window upstairs or walk outside to use your cell phone Like a skylight that brings sunlight into your home zBoost transports and amplifies the outdoor cellular signals into your home or office By following the easy instructions in this user guide you will be Extending Cell Zones into your home or office Why Indoor Signals Can Be Weak There are several obstacles that can contribute to the poor reception you receive in your home or office
8. OT cover Labor charges for set up of the unit Product replacement because of misuse accident lightning damage unauthorized repair or other cause not within the control of Wi Ex Incidental or consequential damages resulting from the product Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you e Any modifications or other changes to the product including but not limited to software or hardware modifications in any way other than as expressly authorized by Wi Ex will void this limited warranty Product that has been modified or adapted to enable it to operate in any country other than the country for which it was designed manufactured approved and or authorized or repair of products damaged by these modifications ZBOOST YX545 SOHO USER GUIDE Make sure you keep Please keep your sales receipt or other document showing proof of purchase Attach it to this User Guide and keep both nearby Also keep the original box and packing material in case you need to return your product Before requesting repair service If red light is on system is receiving signals from either the mobile device or the base station transceiver which are too strong for proper operation Please unplug your system Re orient your Signal Antenna and or Base Unit to reduce the excessive signal source Plug your system back in If still solid red call customer support 1 800
9. ais de la sortie d alimentation ou la r duction de gain et non par un att nuateur la sortie du dispositif Please note This unit has been approved for use in Canada under RSS 131 however consent for the use of this device to improve cellular or PCS coverage must be obtained through your cellular or PCS provider prior to placing the unit in operation Please refer to the Industry Canada document CPC 2 1 05 Section 6 1 available or viewable at http www ic gc ca epic site smt gst nsf en sf08942e html Safety and Product Warranty Information Copyright Notice This manual is copyrighted All rights reserved This manual whole or in part may not be copied photocopied reproduced translated or reduced to any electronic medium or machine readable form for distribution This manual whole or in part may not be modified without prior consent in writing from Wireless Extenders Copyright 2010 by Wireless Extenders Inc Trademarks Wireless Extenders Wi Ex the Wi Ex logo zBoost the zBoost logo and Extending Cell Zones are registered trademarks of Wireless Extenders Inc Safety Guidelines In accordance with FCC requirements of human exposure to radiofrequency fields the radiating element antenna shall be positioned such that a minimum separation distance of 8 inches 20cm is maintained between the radiating element and the user and or general population Limited Liability In no event shall Wireless Extenders b
10. d antenna See page iv ZBOOST YX545 SOHO USER GUIDE Warranty Information Limited 1 Year Warranty Register your product at www Wi Ex com Wi Ex warrants every Wi Ex product to be free from defects in material and workmanship under normal use for the warranty period of one year Who Is Covered You must have proof of purchase to receive warranty service A sales receipt or other documentation showing the product purchased and the purchase date is considered proof of purchase This limited warranty extends only to the original consumer purchaser or any person receiving the product as a gift from the original consumer purchaser and to no other purchaser or transferee This warranty does NOT extend to commercial users What is Covered Warranty coverage begins the day you purchase the product For one year from the original date the Wi Ex Cell Phone Signal Booster will be repaired or replaced with a new repaired refurbished or comparable product whichever is deemed necessary by Wi Ex if it becomes defective or inoperative The exchange will be made without charge to you for parts and labor You will be responsible for the cost of shipping to the location designated by Wi Ex All products including replacement products are covered only for the original warranty period When the warranty on the original product expires the warranty on the replacement product also expires What is Excluded Your warranty does N
11. e lifer i oe amplifier is operating at significantly equal Uplink 824 to 849 MHz Downlink 869 to 894 MHz sods CEL band supported A B A B Networks CDMA GSM GPRS EDGE EVDO 1xRTT UMTS HSPA 3G Solution Increase the distance between antenna and amplifier to achieve maximum performance and coverage reduced coverage Solution Increase space between base unit and antenna Solid RED System is receiving signals from either the mobile device or the base station transceiver which are too strong for proper operation Solutions Move away from receiving antenna with your cell phone Move antenna away from other devices Fast Alternating RED and GREEN The amplifier is disabled followed by no ligh nae eer Bi Solution Unplug and start over General Power Consumption Power Supply Current 3W standby 7W max signal 5 OVDC 2 0A Max Wall Supply Input Voltage 100 240VAC 50 60 Hz System Certifications FCC Parts 15 amp 24 PCS Parts 15 amp 22 CEL Industry Canada Base Unit Size and Weight 5 x7 x 1 25 9 oz Operating Conditions Indoor Use Only 40 105 F After Initial Power Up This product uses patented technology to protect the carrier network Solid GREEN Normal condition Solid RED Pai is receiving signals from either is product Is covered by patent US7 706 7 the mobile device or the base station i transceiver which are too strong for and foreign patents pendi
12. e liable for any direct indirect special punitive incidental exemplary or consequential damages or any damages whether in an action under contract negligence or any other theory arising out of or in connection with the set up of use of inability to use or performance of the information services products and materials available from this manual These limitations shall apply notwithstanding any failure of essential purpose of any limited remedy Because some jurisdictions do not allow limitations on how long an implied warranty last or the exclusion or limitation of liability for consequential or incidental damages the above limitations may not apply to you For full warranty guidelines see page 15 Changes or modifications not expressly approved by Wi Ex could void the user s authority to operate this equipment and or void the product warranty ZBOOST YX545 SOHO USER GUIDE Package Contents zBoost YX545 SOHO Before you begin make sure all of the following parts came with your zBoost YX545 Literature Contents O Set up overview for zBoost YX545 SOHO User Guide online only Product Contents zBoost Base Unit zBoost Base Unit Antenna Power Supply RG 59 mini Coax Cable 50 ft Signal Antenna Signal Antenna Mounting Hardware iii ZBOOST YX545 SOHO USER GUIDE Optional zBoost Accessories The following accessories are available to improve sig
13. ecreasing the distance will limit zBoost performance If 15 feet of separation is not possible you may try our new METRO model which was designed for lofts and urban dwellings and requires no vertical separation Keep the Base Unit off the floor and at least 2 feet away from other cords metal objects or other wireless devices such as wireless routers or wireless access points The zBoost SOHO performs best when there are no obstructions between the zBoost Base Unit and your mobile device Upon initial power up a solid GREEN light should appear indicating normal conditions If a RED light appears adjustments may be needed to optimize performance If you find the increased signal coverage is acceptable however no additional adjustments are needed See Light Indicator section Page 12 for more information An 8 inch window entry cable may beneeded for this option It is availavle for purchase at www Wi Ex com Part YX030 08W ZBOOST YX545 SOHO USER GUIDE BEST PERFORMANCE Attic Outdoor placement The following instructions are recommended for the best reception f Using your cell phone as a signal meter confirm that either your attic or your roof will deliver optimal signal strength to the Signal Antenna Identify the best location for attachment of the mounting bracket such as an attic cross or main beam The coverage your zBoost provides is largely determined by the quality of signal received by the Signa
14. emarks eni ae a a E E EA E EEA EAE EO E a sveensedsateavenstidss ii Safety Guidelines ii Limited Liability cerota neiust E AEE eae ia aie ii Package Contents zBoost YX545 PCS CEL sessessessesesresesreseosesreseesesroseoseseosesreseosesrosesresesesseseeseseeseseeses iii Optional zBoost Accessories s ssssssecssssssssssseceessssssssssecsccscssssesesessssssesesensssssssesessseesessssseseseseesessssseessesees iv Table of Content ssscsccsssssssssssessesssssssssessssssscesssesscsssasssssesessssssssssesesessscsssssesessasecesesssessssasecesessesesssasseesoes 1 Overview Why Indoor Signals Can Be Weak Preparing to Set Up Your zBoost Product s sssssssssssssssssssssssssssesessssssssssssssssssesssessceesssssssssessesscesssseeeenes 3 Tools Needed danii ea EE avastsis ates A st Waste A A A E ET ER 3 Ch ck for Signal Strength seruit neater AEA VE EAE 3 Determine the Needed Coverage Area Determine the Location of Signal Antenna and Base Unit Antenna sssssssssssssssssssesrresrrssresriesrrsssessreess 4 Additional Cable Requirements Misis ania AA A E A AAAS 5 Securing Cable witha Drip Loopreeci A pared i a a a a A Sie iaae 5 Power Requirements wed Setting Up Your zBoost Signal Booster ssssssssssssssssessssssssssssessssssssssesssessesssssssessesssssssssssessesscssssssesessers 6 Placementiof the Signal l ANTENNA naiaren A ANAA A suiacnaiueld oh RAA 6 Easiest See Uparta siete SE E E E R RO
15. ini For better performance you may replace it with RG 6 cable for satellite TV The total cable length should not exceed 70 feet unless you also purchase an upgraded signal antenna see page iv A longer cable is helpful only if it allows you to place the Signal Antenna in a location where you measure stronger signal Avoid placing the Signal Antenna near metal such as wiring A C ducts metal siding truss plates etc When connecting the cable to the antenna run the cable straight down from the antenna Avoid draping the coax near the antenna Grounding the Signal Antenna If you decide to place the Signal Antenna outdoors it must be properly grounded See page iv for a recommented grounding kit The set up must be in accordance with Article 810 of the National Electric Code NEC A listed antenna discharge unit must be provided for the lead in coaxial cable per NEC article 8 10 20 or the shield of the coaxial cable must be permanently and effectively grounded in accordance with NEC article 8 10 21 Please consult a professional installer or electrician for more information See page iv Securing Cable with a Drip Loop If you place the Signal Antenna outdoors create a drip loop with the coaxial cable at the point where the cable enters the building through an outside wall This can be done by twisting and securing the cable into a loop no less than 4 across near the entry point This will help prevent moisture from ga
16. ional antenna that delivers signal in a circular pattern around the antenna 6 Connect the zBoost Base Unit to the provided power supply and plug into a power outlet When your zBoost system is in place and fully connected walk throughout your home or office and verify that you are able to reliably place calls If the signal strength has improved your zBoost is working Remember coverage varies based on outdoor signal level building construction and antenna placement Coverage in adjoining rooms next to above or below will be reduced by walls and ceiling floors ZBOOST YX545 SOHO USER GUIDE NOTE The zBoost YX545 SOHO requires at least 15 feet of vertical separation between the Base Unit and the Signal Antenna Generally increasing this distance up to 40 feet will increase the performance and decreasing the distance will limit zBoost performance If 15 feet of separation is not possible you may try our new METRO model which was designed for lofts and urban dwellings and requires no vertical separation Keep the Base Unit off the floor and at least 2 feet away from other cords metal objects or other wireless devices such as wireless routers or wireless access points The zBoost SOHO performs best when there are no obstructions between the zBoost Base Unit and your mobile device Upon initial power up a solid GREEN light should appear indicating normal conditions If a RED light appears adjustments may be needed to
17. l Antenna 2 Secure the mounting bracket at the highest possible point and at least 3 feet 1 meter away from metal objects such as pipes metal siding A C unit etc Best Performance Place Signal Antenna on roof or in attic 3 Position the mounting bracket such that the Signal Antenna will be vertical and attach the Signal Antenna See page 4 for more information 4 Connect the supplied coaxial cable to the base of the Signal Antenna Run the coaxial cable along a descending pipe or through a wall that that leads closest to the location of the Base Unit Use the provided 50 feet of RG 59 mini coaxial cable to connect the Signal Antenna and the Base Unit Should you need additional cable length 15 foot extensions Part YX30 15w are available at www Wi Ex com Please note Cable longer than 75 feet is not recommended Base Unit Antenna zBoost Base Unit Coaxial Cable Power Supply NOTE Refrain from securing cable or drilling holes until the system has been tested 5 From the other end connect the coax cable it to the Base Unit Assemble the Base Unit Antenna Connect the Base Unit Antenna to the Base Unit and place it where you need signal Place the zBoost Base Unit where you want to create a Cell Zone For the widest possible signal area it is recommended that you position the Base Unit near the middle of a room or mount it on an interior wall This Base Unit uses an omni direct
18. le at ground level check the signal strength in your attic or at roof level location where the signal will likely be stronger and where the Signal Antenna can be placed for best performance If you can reliably make and receive calls outside your home then zBoost can bring the signal into your home If only one signal bar is displayed on your cell phone outside indoor coverage will be limited to one small room We recommend placing the Signal Antenna outside and or purchasing a Wi Ex upgrade Signal Antenna for increased coverage see page iv Cell phone signal bars are approximate and vary from phone to phone The number of bars can fluctuate widely depending on the location of the phone the position or angle of the phone weather etc Most cell phone signal meters update every 6 to 10 seconds An increase of only one bar typically indicates a 4x to 10x signal increase ZBOOST YX545 SOHO USER GUIDE Determine the Needed Coverage Area Identify the location in your home office where you need signal coverage the most The zBoost YX545 SOHO can cover upto 2500 square feet coverage varies based on outdoor signal level building construction and placement of antennas Walls ceilings or floors will reduce the coverage area MASTER BEDROOM BEDROOM Determine the Location of Signal Antenna and Base Unit Antenna It is recommended that the Signal Antenna and Base Unit Antenna have at least 15 feet of vertical separation
19. nal reception and provide increased coverage in your home or office Please see our website for complete selection To order call 1 800 871 1612 or visit www Wi Ex com YX545 Dual Band Part Description Bi Directional receiving Signal Antenna upgrade YX039 PCS CEL 13 dBi PCS 8 dBi CEL porc Diona cing Sigal Anma pee OOO E ving sil anon upgrade 62 rxas rcs Dison sing Sigal Anson upgrade 138 YX024 PCS Directional transmitting Base Unit Antenna upgrade 7 dBi YX026 CEL Directional receiving Signal Antenna upgrade 11 dBi Directional transmitting Base Unit Antenna upgrade YRO27 PCS CEL 9 dBi PCS 6 dBi CEL Directional transmitting window mount Base Unit Antenna upgrade YXO28 PCS CEL 9 dBi PCS 6 dBi CEL 15 ft Signal Antenna coax extension low loss RG 6 35 ft Signal Antenna coax extension cable low loss RG 6 Omni Directional transmitting ceiling mount Base Unit Antenna 2 YX050 PCS CEL dBi PCS 1 dBi CEL o YX055 CEL CEL Directional Outdoor Yagi Antenna 15 dBi ZBOOST YX545 SOHO USER GUIDE Table of Contents About zBoose from Wie Bx suira gii RAKAR ERR RRRA A E RAR i FOG Trformiation esseeccessiti seenzess sassieoncss aa a a a a a a a aa l i Industry Canada Regulations Safety and Product Warranty Information ssssssssssssssssssssssesscsssssssssssssscessssesssssssscssessesssssssssesessesesseseee ii Copyright Notices Sepa r in ETE E ERRE A AA AR ii Trad
20. ng proper operation Solution Please unplug your system Re orient your Signal Antenna and or Base Unit to reduce the excessive signal source Plug your system back in If still solid red call customer support 1 800 871 1612 ZBOOST YX545 SOHO USER GUIDE Frequently Asked Questions What can I expect my cell phone signal range and strength to be inside my home or office The closer you are to the base the stronger the signal This will vary with different conditions Some of the conditions that will affect the improved coverage area are signal strength outdoors the type of building materials in the home the placement of the unit and the antenna s proximity to cellular towers You can expect that your indoor coverage will be improved You will be able to make calls where you couldn t before The degree of improvement will depend upon many factors The intent of zBoost products are to bring outside coverage inside Just as the signal bars move up and down when outside the boosted signal will fluctuate in a similar fashion Is a cellular phone signal booster the same as a wireless router will it help my WiFi signal The Wi Ex unit will not help your WiFi service This unit is designed to work with wireless PCS and Cellular phones and devices The WIFI in your home or office operates on a different frequency Is your product available for international use Yes we have products that work on European frequencies Our
21. nna and the Signal Antenna Purchase an upgrade antenna available at www Wi Ex com NOTE The zBoost YX545 SOHOrequires at least 15 feet of vertical separation between the Base Unit and the Signal Antenna Generally increasing this distance up to 40 feet will increase the performance and decreasing the distance will limit zBoost performance If 15 feet of separation is not possible you may try our new METRO model which was designed for lofts and urban dwellings and requires no vertical separation Keep the Base Unit off the floor and at least 2 feet away from other cords metal objects or other wireless devices such as wireless routers or wireless access points The zBoost SOHO performs best when there are no obstructions between the zBoost Base Unit and your mobile device BEDROOM ZBOOST YX545 SOHO USER GUIDE ZBOOST YX545 SOHO USER GUIDE zBoost Base Unit Light Indicators Technical Specifications At Initial Power Up Only Solid GREEN Normal condition at power up Slowly Alternating RED and GREEN zBoost is working but at reduced performance and coverage due to non ideal setup Product Specifications for zBoost YX545 SOHO Dual Band PCS band Frequency Uplink 1850 to 1910 MHz Downlink 1930 to 1990 MHz PCS band supported A D B E EC Networks CDMA GSM GPRS EDGE EVDO 1xRTT UMTS HSPA 3G Fast Flashing RED Indicates insufficient distance between the an chaa adto amplifier Th
22. ny interference received including interference that may cause undesired operation The term IC before the radio certification number only signifies that Industry Canada technical specifications were met RF Exposure The manufacturer s rated output power of this equipment is for single carrier operation For situations when multiple carrier signals are present the rating would have to be reduced by 3 5 dB especially where the output is re radiated and can cause interference to adjacent band users This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device ZBOOST YX545 SOHO USER GUIDE Cet appareillage num rique de la classe B r pond toutes les exigences de l interf rence canadienne causant des r glements d quipement L op ration est sujette aux deux conditions suivantes 1 ce dispositif peut ne pas causer l interf rence nocive et 2 ce dispositif doit accepter nimporte quelle interf rence re ue y compris l interf rence qui peut causer l op ration peu d sir e Le fabricant nominale de la puissance de sortie de ce mat riel est simple transporteur Pour les situations lorsque plusieurs signauxporteurs sont pr sents valuation devrait tre r duite de 3 5 dB en particulier lorsque le signal de sortie est r mise et peut provoquer des interf rences adjacentes la bande utilisateurs Ce pouvoir est de la r duction par le bi
23. one and check the signal meter 3 Plug the power cord into the Base Unit 4 Hold your cell phone about 5 feet from the Base Unit and then turn it on Wait up to 1 minute for the cell phone to register the signal coming from the Base Unit By If the signal meter shows improvement your zBoost unit is working properly Cell phone signal bars are approximate and vary from phone to phone The number of bars can fluctuate widely depending on the location of the phone the position or angle of the phone weather etc Most cell phone signal meters update every 6 to 10 seconds An increase of only one bar typically indicates a 4x to 10x signal increase THE BEST INDICATOR OF PRODUCT PERFORMANCE IS THE ABILITY TO RELIABLY PLACE AND RECEIVE CALLS WHERE YOU COULD NOT BEFORE SETTING UP THE YX545 SOHO ZBOOST YX545 SOHO USER GUIDE Improving Your Coverage Area When your zBoost system is in place and fully connected you should walk throughout the room and see that you are able to reliably place calls Remember coverage varies based on outdoor signal level building construction and antenna placement Coverage in adjoining rooms next to above or below will be reduced due to walls or ceiling floors Should you desire to improve coverage you may Relocate the Signal Antenna in order to capture a better signal higher is usually better and outside is better than inside Increase the distance between the Base Unit Ante
24. thering at entry point and leaking into the building Consult a professional installer if you need more information Power Requirements The Base Unit can be plugged into a standard 2 or 3 prong 110 VAC receptacle using the Included power supply The power supply consumes less than 10W less than 0 2A The zBoost YX545 SOHO base unit MUST only be used with the provided power adaptor Use of other power adaptors will void the warranty and may damage the unit Use of other equipment is not FCC approved ZBOOST YX545 SOHO USER GUIDE Setting Up Your zBoost Signal Booster Placement of the Signal Antenna Choosing the best location for the Signal Antenna provides the best performance and the largest area of improved signal Determine the location that provides the strongest signal using the signal strength indicator on your cell phone Find the location that provides the most bars of signal strength and place the Signal Antenna at or near that location Assemble the Signal Antenna mounting bracket as shown on page 4 Avoid placing the Signal Antenna near metal such as wiring A C ducts metal siding truss plates etc When connecting the cable to the antenna run the cable straight down from the antenna Avoid draping the coax near the antenna Choose 1 of the following 3 options for setting up your zBoost system O EASIEST Inside by a window Locate a window where you get service 1 Mount the Signal Antenna abo
25. ve the window The coverage your zBoost provides is largely determined by the quality of signal received by the Signal Antenna 2 Assemble the Base Unit Antenna Place the Base Unit in desired location where you want to create a Cell Zone 15 feet of vertical separation between the Base Unit and Signal Antenna is recommended Connect the Base Unit Antenna to the Base Unit and place it where you need signal Easiest Set up Place Signal Antenna inside by a window Attach the coaxial cable to the Signal Antenna 3 4 Connect the other end of the coaxial cable to the Base Unit 5 Attach the Base Unit Antenna to the Base Unit and position it vertically 6 Connect the Power Supply to the Base Unit and plug into a power outlet NOTE The zBoost YX545 SOHO requires at least 15 feet of vertical separation between the Base Unit and the Signal Antenna Generally increasing this distance up to 40 feet will increase the performance and decreasing the distance will limit zBoost performance If 15 feet of separation is not possible you may try our new METRO model which was designed for lofts and urban dwellings and requires no vertical separation Keep the Base Unit off the floor and at least 2 feet away from other cords metal objects or other wireless devices such as wireless routers or wireless access points The zBoost SOHO performs best when there are no obstructions between the zBoost Base Unit and
26. your mobile device Upon initial power up a solid GREEN light should appear indicating normal conditions If a RED light appears adjustments may be needed to optimize performance If you find the increased signal coverage is acceptable however no additional adjustments are needed See Light Indicator section Page 12 for more information ZBOOST YX545 SOHO USER GUIDE BETTER PERFORMANCE Outside of a window Locate a window where you get signal 1 Mount the Signal Antenna outside of the window The coverage your zBoost provides is largely determined by the quality of signal received by the Signal Antenna 2 Assemble the Base Unit Antenna Place the Base Unit in desired location where you want to create a Cell Zone 15 feet of vertical separation between the Base Unit and Signal Antenna is recommended Attach the coaxial cable to the Signal Antenna 4 Run the coaxial cable from the Signal Antenna through the window an optional window entry kit is available see page iv and to the Base Unit Better Performance Place Signal Antenna 5 Attach the Base Unit Antenna to the Base Unit and position it outside of window vertically 6 Connect the Power Supply to the Base Unit and plug into a power outlet NOTE The zBoost SOHO requires at least 15 feet of vertical separation between the Base Unit and the Signal Antenna Generally increasing this distance up to 40 feet will increase the performance and d
27. zBoost extending cell zones By VV i E Xom zBoost YX545 SOHO User Guide 30 day money back guarantee when you buy directly from Wi Ex If product is purchased from a reseller or third party you must use their return policy 1 Year Manufacturer Warranty Register your zBoost product at www Wi Ex com v2 0910 ZBOOST YX545 SOHO USER GUIDE ZBOOST YX545 SOHO USER GUIDE About zBoost from Wi Ex Wi Ex is the leader in cell phone signal boosters zBoost enhances the performance of your cell phone PDA and wireless data card Compatibility Dual Band zBoosts are compatible with 800MHz and 1900MHz regardless of technology including CDMA and GSM Patented technologies protect the carrier network 1 year manufacturer warranty register your product at www Wi Ex com zBoost products have more awards more sales and more locations than all other signal boosters COMBINED FCC Information FCC ID SO4YX545 PCS CEL Warning Changes or modifications to this device not expressly approved by Wi Ex could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if
Download Pdf Manuals
Related Search