Godex EZ-2300Plus
Contents
1. ame R 48 gt 6000 Plus 4 7 Installing the parallel PS 2 adapter Parallel cable 1 Check whether the printer is switched off Place the printer on a flat surface and open the printer cover p a8 y jam a A 4 p LA E a ms ae Unscrew the two screws marked in the illustration on the right and remove the left hand side of the printer housing Unscrew the screws on the parallel port cover and remove the cover EZ2000 Plus EZ6000 Plus User Manual 49 Install the parallel PS 2 adapter in its place and secure it on the housing with screws Connect the 30 pin connection cable to the motherboard Replace the left hand part of the printer housing and secure it with the screws you removed earlier Installation of the parallel PS 2 adapter is now complete EZ2000 Plus EZ6000 Plus User Manual 50 4 8 Installing the applicator interface Applicator interface Screws set of 2 Place the printer on a flat surface and open the printer cover Note Remember to switch off the printer before starting the installation Unscrew the two screws marked in the illustration on the right and remove the left hand side of the printer housing Unscrew the screws on the applicator interface cover and remove the cover EZ2000 Plus EZ6000 Plus User Manual 51 Pass the applicator cable through the opening into the housi2. cccconccccccnncnncconcncnonannnnonononnnonaroncnononnnos 60 5 6 Ribbon shield SOUS o o cea tuia o lea eo 61 a fie NEN SN UU o ee ee 62 9 97 LTOUDISSMOOUNG TT 63 EZ2000 Plus EZ6000 Plus User Manual 3 1 Barcode printer 1 1 Box content Please check that all of the following items are included with your printer Barcode printer Power cord USB cable Label stock Ribbon Empty ribbon core Quick reference guide CD with QLabel label software user manual 909898899 1 2 Specifications EZ2000 Plus series lodel EZ2200 Plus EZ2300 Plus Print Method Thermal Transfer Direct Thermal Resolution 203 dpi 8 dot mm Print Width 4 09 104 mm Min 0 16 4 mm Min 0 16 4 mm PrintLengtn My 109 4872 imm GUN Types Continuous form gap labels black mark sensing and punched hole label length set by auto sensing or programming Width Tear 1 25 4 mm Min 4 64 118 mm Max Width Cutter 4 61 117 mm Max Width Label Dispenser Rewind 4 64 118 mm Max Thickness 0 003 0 06 mm Min 0 01 0 25 mm Max Label roll diameter Max 8 203 2 mm with 3 76 2 mm core Max 6 152 4 mm with 1 5 38 1 mm core Core diameter 1 5 38 1 mm 3 76 2 mm Types Wax wax resin resin Length 1471 450 m Ribbon Width 1 18 Min 4 33 30 mm 110 mm Max Ribbon roll diameter 2 99 76 mm Core diameter 1 25 4 mm Auto ink inside and ink outside
3. Adjust Stop Position Printhead Position Stop Position Printing Mode Option Setup Sensor Setup COM Port Setup Auto Sensor LCD Language CodePage Setup Keyboard Setup Keyboard Mode Buzzer Setup Smart Backfeed_ Password TopofForm USB Ethernet Lock Setup From0to19 From 2to 7 IPS From 0 to 10 mm From 100 to 100 From 0 to 40 mm Direct Thermal Strip Mode Cutter Mode None Black Mark Gap Continuous BaudRate Party fr DataBis StopBits 4800 bps Non Parity 7 bits 1 bit 9600 bps Odd Parity _ 8 bits 2 bits 19200 bps Even Parity 38400 bps 57600 bps 115200 bps Auto Mode Gap Mode Black Mark Mode English Simplified Chinese Espa ol Italiano Deutsch Francais T rk e Code Page 850 1Code page 852 Windows 1255 US H uk H French German Spanish Italian Finnish H Dutch Belgian Recall Label L Keyboard Setup Code page setup Printing Option Clock Setup L J Exit KB Mode Enter Keyboard Q Printer Prompts Clock Setting Recall Label Indefinite Clock Display Select Label Fixed Traditional Chinese Print Quantity ON OFF ON OFF E ON FH OFF L UM r RE 1 USB jf Ethernet EVERYTHING H DARKNESS HH SPEED H STOP POS AD STOP POS 4PRINTHEA
4. 180 270 rotatable single characters 90 180 270 Resident Fonts rotatable Bitmap fonts 8 times expandable in horizontal and vertical directions Scalable fonts 90 180 270 rotatable Bitmap fonts 90 180 270 rotatable single characters 90 180 270 rotatable Download Fonts Asian fonts 90 180 270 rotatable and 8 times expandable in horizontal and vertical directions Scalable fonts 90 180 270 rotatable Ribbon EZ2000 Plus EZ6000 Plus User Manual 6 1 D Bar codes Code 39 Code 93 Code 128 subset A B C UCC EAN 128 K Mart UCC EAN 128 UPC A E add on 2 amp 5 12 of 5 2 of 5 with Shipping Bearer Barcodes Bars EAN 8 13 add on 2 5 Codabar Post NET EAN 128 DUN 14 HIBC MSI 1 Mod 10 Random Weight Telepen FIM China Postal Code RPS 128 and GS1 DataBar PDF417 Datamatrix code MaxiCode QR code and Micro QR code CODEPAGE 437 850 851 852 855 857 860 861 862 863 865 866 869 Code Pages L WINDOWS 1250 1251 1252 1253 1254 1255 Unicode UTF8 UTF16 EIE 0 vada MN downloadable from the software o D port RS 232 DB 9 USB port default on CF Card socket Ethernet 10 100Mbps print server default off disables USB when in use Backlit graphics LCD display 128 x 64 dots or 4 lines x 16 characters Control Panel Three mono color status LEDs Power on Ribbon out Media out Control keys FEED PAUSE and CANCEL Real Time Clock Power Auto Switching 100
5. file and click it to start the installation Follow the instructions on the screen The Driver Wizard guides you through the installation procedure 4 Select Install printer drivers Specify your printer model Windows Drivers File Edit View O9 0 P kK Back Forward Up Cut Favorites Tools Help Ha gt Copy Paste Search Address y Dei Windows Drivers File and Folder Tasks ca Make a new Folder des adi sPrinterDriver a Publish this Folder to the i exe web EJ Share this folder Seagull Driver Wizard Welcome to the Seaqull Driver Wizard This wizard helps you install and remove printer drivers What would you like Eo do CO Upgrade printer drivers Q Remove printer drivers Seagull Driver Wizard Specify Printer Model The manufacturer and model determine which printer driver to use Specify the model of your printer Printer Model Godex EZ 1300 Plus Godex EZ 1300 Plus GEPL Godex EZ 1305 Godex EZ 1305 GEPL Godex EZ 2100 Plus Godex EZ 2200 Godex EZ 2300 Plus Godex EZ 2200 Plus GEPL rd CF Am CA Seagull 7 1 7 M 0 08 06 2009 Source Version Browse EZ2000 Plus EZ6000 Plus User Manual 18 Specify the port used to Seagull Driver Wizard connect the printer to the Specify Port host com puter 4 port is used to connect a printer to the computer Specify Ehe port that you are using IF you are connecting using TCP IP a
6. 10 100Mbps print server default off disables USB when in use Backlit graphics LCD display 128 x 64 dots or 4 lines x 16 characters Three mono color status LEDs Power on Ribbon out Media out Control keys FEED PAUSE and CANCEL Standard Auto Switching 100 240VAC 50 60Hz Operation temperature 41 F to 104 F 5 C to 40 C Storage temperature 4 F to 122 F 20 C to 50 C Operation 30 85 non condensing Storage 10 90 non condensing CE EMC FCC Class A CB cUL CCC Length 20 15 512 mm Height 11 45 291 mm Width 10 78 274 mm Weight 33 lbs 15Kg excluding consumables Cutter Module Internal Rewinder with Label Dispenser peel Parallel port Centronics 36 pin and PS2 port Applicator Interface 1 input 3 outputs power 500mA 5V 802 11 b g wireless print server Default off disables USB when in use Must remove Ethernet card to install External label roll holder for 10 250 mm O D label rolls External label rewinder Specifications are subject to change without notice All company and or product names are trademarks and or registered trademarks of their respective owners Minimum print height specification compliance can be dependent on non standard material variables such as label type thickness spacing liner construction etc Godex is pleased to test non standard materials for minimum height printing capability Control Panel Real Time Clock Humidity
7. 2 Remove the lower cover plate Note Switch off the printer before starting the installation 3 Remove the two screws securing the tear off plate then remove the tear off plate 4 Secure the dispenser module on the printer using two screws EZ2000 Plus EZ6000 Plus User Manual 44 Connect the dispenser cable connector to the rewinder jack Route the connection cable along the bottom of the printer housing using the cable clips Pull out the print head release lever and turn it anticlockwise to a top right position Using the lever shown in the illustration 1 fold out the dispenser module in the direction indicated by the arrow 2 otrip a few labels off the label liner approx 400 mm and pass the label liner through the dispenser module Close the dispenser module again EZ2000 Plus EZ6000 Plus User Manual 45 11 Wind the label liner around the rewinder and secure it using the retention clip 12 Return the print head release lever to its original position Note The dispenser can only be used with labels of a minimum height of 20 mm Suggestion When using the label dispenser you should set the stop position to 25 mm 13 Close the printer cover to complete installation of the dispenser Note Before you start using the rewinder send the command AXSET REWINDER 1 to the printer to enable the rewind function EZ2000 Plus EZ6000 Plus User Manual 46 4 6 In
8. Agency Approvals EZ2000 Plus EZ6000 Plus User Manual 5 Print Method Thermal Transfer Direct Thermal 03 dpi 8 dot mm 300 dpi 12 dot mm Model EZ6200 Plus EZ6300 Plus i 2 Print Speed 6 IPS 150 mm s 4 IPS 102 mm s Print Width 61 168 mm Min 0 16 4 mm Min 0 16 4 mm Print Length ax 118 3000 mm Max 54 1371 mm Memory _ 4MB Flash 2MB for user storage 16MB SDRAM Sensor Type Adjustable reflective sensor and transmissive sensor left aligned Types Continuous form gap labels black mark sensing and punched hole label length set by auto sensing or programming Width Tear 2 50 8 mm Min 7 178 mm Max Width Cutter 6 5 165 mm Max Width Heavy duty cutter 6 8 172 mm Max Width Label Dispenser Rewind 7 178 mm Max Thickness 0 003 0 06 mm Min 0 01 0 25 mm Max Label roll diameter Max 8 203 2 mm with 3 76 2 mm core Max 6 152 4 mm with 1 5 38 1 mm core Core diameter 1 5 38 1 mm 3 76 2 mm Types Wax wax resin resin Length 1471 450 m Width 2 36 Min 6 85 60 mm 174 mm Max Ribbon roll diameter 2 99 76 mm Core diameter 1 25 4 mm Auto ink inside and ink outside Printer Language EZPL Firmware upgradable Software Spe design software QLabel IV for EZPL only Driver amp DLL Windows 2000 XP and Vista Bitmap fonts 6 8 10 12 14 18 24 30 16X26 and OCR A amp B Bitmap fonts 90
9. installed Image buffer size 1500K 000 FORM S IN MEMORY 000 GRAPHIC S IN MEMORY 000 FONT S IN MEMORY 000 ASIAN FONT S IN MEMORY 000 DATABASE S IN MEMORY 000 TTF S IN MEMORY 2048K BYTES FREE MEMORY AS4 H10 ROO0 R200 W100 Q100 0 3 EO Option DO OO AD See through Volt 0 8 0 5 0 2 0 6 Code Page 850 Date Time 2010 05 13 11 37 Network ON LINE Interface LAN MAC XX XX XX XX XX XX IP protocol dhcp IP address XXX XXX XXX XXX Netmask XXX XXX XXX XXX Gateway XXX XXX XXX XXX DNS XXX XXX XXX XXX 27 3 5 Dump mode If the label settings do not match the printer output you should switch the printer to dump mode to check whether an error has occurred during the transfer between printer and host computer In dump mode the unprocessed raw data are sent to the printer and printed This shows you quickly whether any data are sent to the printer at all Here is how you switch to dump mode 1 Switch off the printer 2 Switch on the printer keeping the FEED button pressed 3 When the message Dump Mode appears on the display release the FEED button The printer will automatically print Dump Mode Begin That means the printer is now in dump mode 4 Send commands to the printer and check whether they match the printer output To exit dump mode press the FEED button The printer will automatically print Out Of Dump Mode and switch to standby mode Alternatively you can switch off the printer to e
10. product name example Apple The input form for the second variable is now shown on the display Specify a random value example 199 The input form for the print quantity is now shown on the display opecify a quantity example 3 The printer will print three labels with the values for the two variables and the serial number specified EZ2000 Plus EZ6000 Plus User Manual 31 3 8 Error alerts In the event of a problem that prevents normal functioning of the printer you will see an error message on the display and hear some beep signals The LED indicators above the display will also light up P ME bast flashing e Slow flashing Q Light on N d A CI message displayed RIBBON MEDIA The print Please make sure Print head Both LEDs inBchamem that the print is open light up re coed mechanism is closed correctly i Once the print head pud lt Y Both Mcd 5 has cooled down 9 NET NEM flashing the printer switches process hot to standby mode Please make sure No ribbon is that the printer is loaded set to thermal direct mode Out of 3x2 ribbon beeps The ribbon is finished or Heplace the ribbon the ribbon P roll roll is not moving Please make sure that the gap sensor nabieto is positioned d correctly If that etect the d fix th paper oes not fix the Out of 1x2 problem run the media beeps auto detection function again The labels i aa
11. release lever as shown in the illustration 1 and turn it anticlockwise to a top right position 2 TPH print line adjustment When printing is slow or when printing on thick label stock the print line must be moved to the front in paper feed direction for a better print result Using a flat head screwdriver turn the screws clockwise to move the TPH forward The two screws on the left and right must be adjusted to the same position to ensure the print line and feed roller are in parallel One turn of the screw moves the print head by 0 5 mm To keep track of the change in quality you should adjust the screws by Ya turn at a time If no improvement is visible gently turn the screws clockwise as far as possible then restart the adjustment process from there EZ2000 Plus EZ6000 Plus User Manual 57 5 3 Adjusting the ribbon tension You can adjust the ribbon tension by turning the ribbon shaft knob green wheel at the base of the ribbon supply hub see illustration clockwise or anticlockwise There are 4 possible settings which are marked on the knob of the ribbon rewind hub and the ribbon supply hub When set to 1 the tension is highest while the tension is lowest at 4 If the tension is so low that the ribbon does not move forward you need to reduce the tension of the ribbon supply hub or increase the tension of the ribbon rewind hub To set the tension press in the knob and turn it clockwise
12. the label i Possible reason Paper jam oaper feed problem Please follow the CF card Both 2x2 The CF card instructions in Ho flashing beeps o Section 4 4 to formatted formatted format the CF card EZ2000 Plus EZ6000 Plus User Manual 32 File name not found File name already exists The memory is full Unable to find file The file name already exists Delete data you no longer need from the memory or use a CF card Use the X4 command to print all file names and check whether the file exists in the memory Change the name of the file and try storing it again 3 9 Instructions for using the CF card All EZ2000 Plus and EZ6000 Plus series printers will recognise the CF card If the printer s internal memory is not sufficient to store label formats graphics or fonts you can use the CF card as an external memory to increase the storage capacity Please follow these instructions when using the CF card 1 Remember to switch off the printer before installing the CF card or removing it from the card slot 2 The CF card must be formatted to FAT16 before you can use it as external memory for the printer When an unformatted CF card is detected the printer beeps three times and the STATUS indicator flashes orange 3 To format the CF card press the FEED button The printer then formats the card to FAT16 When formatting is complete the LED indicator lights up green 4 f you do not wish t
13. the nut 11 Screw the antenna onto the antenna connector You can now adjust the angle of the antenna as required 12 Replace the left hand part of the printer housing to complete the installation Note 1 Once you have finished installing the Ethernet module the command AXSET USBETHERNET 1 must be sent to the printer to enable the Ethernet module While the Ethernet module is enabled the USB port is disabled To enable it again send the command XSET USBETHERNET 0 to the printer Note 2 The wireless network must be configured via a network cable EZ2000 Plus EZ6000 Plus User Manual 55 5 Maintenance and adjustment 5 1 Installing removing the print head modul 1 Open the printer cover I Note Remember to switch off the printer before removing the print head module Pull out the print head release lever as shown in the illustration 1 and turn it anticlockwise to a top right position 2 Hold the print head module at the front and gently pull it out If you cannot remove the module by gently pulling it use a screwdriver as shown in the illustration Hold the module at the front and slide it into the printer along the guide rails Firmly press the module in so the contacts are fully connected EZ2000 Plus EZ6000 Plus User Manual 56 5 2 Adjusting the print line Please contact your local dealer for technical support 1 Open the printer cover Pull out the print head
14. the printer housing Now attach the rewinder connector bracket supplied Connect the rewinder connector bracket to the motherboard as shown in the illustration Remove the cover for the rewinder module Remove the retention clip from the rewinder Secure the rewinder on the printer housing using the four screws supplied Note Please make sure that all rewinder cable connectors are arranged on the side of the motherboard before you tighten the screws that secure the rewinder 13 Connect the Rewinder full switch to the jack on the rewinder connector bracket EZ2000 Plus EZ6000 Plus User Manual 40 14 Install the motor in the back section of the printer housing and align it with the 4 screw holes 15 Do not tighten the screws fully to leave room for installing the belt If required adjust the position of the motor during installation of the belt Now tighten the screws securing the motor 18 Gently pull the rewinder connection cables so they are fully inside the printer housing EZ2000 Plus EZ6000 Plus User Manual 41 Connect the cable with the 5 pin connector to the jack marked CUTTER on the motherboard Connect the cable with the 4 pin connector to the jack marked STRIP on the motherboard Connect the remaining connector to the motor Attach the motor cable and the Rewinder full cable to the motor bracket using the cable tie Note You should position the
15. 240VAC 50 60Hz Operation temperature 41 F to 104 F 5 C to 40 C Envirenment Storage temperature 4 F to 122 F 20 C to 50 C E Operation 30 85 non condensing ey Storage 10 90 non condensing Agency Approvals CE EMC FCC Class A CB cUL CCC Length 20 31 516 mm Height 11 22 285 mm Width 13 58 345 mm Weight 36 8 lbs 16 7Kg excluding consumables Cutter Module Internal Rewinder with Label Dispenser peel Parallel port Centronics 36 pin and PS2 port Applicator Interface 1 input 3 outputs power 500mA 5V 802 11 b g wireless print server Default off disables USB when in use Must remove Ethernet card to install External label roll holder for 10 250 mm O D label rolls External label rewinder Specifications are subject to change without notice All company and or product names are trademarks and or registered trademarks of their respective owners Minimum print height specification compliance can be dependent on non standard material variables such as label type thickness spacing liner construction etc Godex is pleased to test non standard materials for minimum height printing capability EZ2000 Plus EZ6000 Plus User Manual 7 1 3 Interfaces Parallel port Handshaking DSTB is sent to the printer BUSY to the host computer e Parallel cable compatible with IBM computers Pinout See below Strobe Data 0 7 Acknowledge Busy Paper empty Select Aut
16. 5 CISPR 22 3rd Edition 1997 Class A ANSI C63 4 2001 CNS 13438 IEC60950 1 2001 GB4943 2001 GB9254 1998 GB17625 1 2003 EN60950 1 2001 CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions opecifications are subject to change without notice EZ2000 Plus EZ6000 Plus User Manual 1 Safety instructions Please read the following instructions carefully 1 Keep the equipment away from humidity Before you connect the equipment to the power outlet please check the voltage of the power source Make sure the printer is off before plugging the power connector into the power jack It is recommended that you connect the printer to a surge protector to prevent possible transient overvoltage damage Be careful not to get liquid on the equipment to avoid electrical shock For safety and warranty reasons ONLY qualified service personnel should open the equipment Do not repair or adjust energized equipment under any circumstances EZ2000 Plus EZ6000 Plus User Manual 2 T BAHGODE PRINTER TTT 4 ES Miser doom Ed 4 25 pPECMICa ON NE T ODDS 4 CERIS RII SR A ETE o 8 1 4 Getting to know your DIN avi eee eee shed Un ense ibl Eae usu cu due AAA AA 11 2 PRINTER SETUP uan 13 2 1 Loading the labels ds 13 2 2 LO AGING ne AID utu nita teet sedan du SES KEN P
17. D POS HH PRINTING MODE H OPTION SETUP SENSOR SETUP FF OFF OFF COMPORT SETUP L J AUTO SENSOR LCD LANGUAGE H CODEPAGE KEYBOARD 4 BUZZER SMART BACKFEED TOP OF FORM Items marked are the default settings 26 EZ2000 Plus EZ6000 Plus User Manual 3 4 Self test The self test function lets you check whether the printer is functioning normally Here is how you run a self test 1 2 3 Switch off the printer Switch on the printer keeping the FEED button pressed until you hear 3 beeps and the message Self test is shown on the display After about one second the printer will automatically print out the list below That means the printer is functioning normally Model amp Version Serial port setup USB port setting Test pattern Number of DRAM installed Image buffer size Number of forms Number of graphics Number of fonts Number of Asian fonts Number of Databases Number of Scalable fonts Free memory size Speed Density Ref Point Print direction Label width Form length Stop position Cutter Label Dispenser Mode Sensor Setting Code Page Current time setting in RTC Network connection status Network connection interface MAC address of LAN WLAN module IP protocol setting IP address of LAN WLAN module Netmask setting Gateway setting DNS setting EZ2000 Plus EZ6000 Plus User Manual EZXXXX VX XXX Serial port 96 N 8 1 int usb sw setting ext USB 1 DRAM
18. E Ld cdo 16 2 3 Connecting the printer to the host computer esse eee eee eee eee 17 2 4 Installing NE ENE ancianas 18 3 OPERATOR PANEL 5r rasa 20 3 1 Operator panel IMrOQUCUOM sietan a a Eae a A a aN N 20 3 2 Function buttons Tanesha T 20 X E INS MOS TE ET a 22 S elc BI A PP e 27 A OTROS 28 3 5 EaDEl Size calibFallOizs dei a eo tA ae 28 3 7 KEVDO SA MOG Ci o 29 3 0 69 Bel a oe ee ene eo ee nee ee eT een eee eee ee ee utut er dust das 32 3 9 Instructions for using the CF Card eee eee 33 A AGCESSOBIES TTT 34 4 1 Internal rewinder EZ2000 PIUS sse eee ee eee 34 4 2 Installing the rewinder guide EZ2000 PIUS see eee ee 36 4 3 Labeldispenser tEZ2000 PIUS oi dies 37 4 4 Internal rewinder for EZ6000 PIUS sees eee eee eee eee 39 4 5 Installing the label dispenser EZ6000 Plus with rewinder 44 4 6 Installing tie CUTIGE sees ene mes aiuti Veo co dae vc tede lee orien kk Ste storie inan 47 4 7 Installing the parallel PS 2 adapter sse eee 49 4 8 Installing the applicator interface see eee eee eee 51 5 MAINTENANCE AND ADJUSTMENT 56 5 1 Installing removing the print head module sse eee eee eee 56 5 2 Adjustng Ime sls Tan IE a iia 57 5 3 AdJjustinig the ribbon TENSION asii arc a re ead mca e bc d cow Ma eie tia o Edd 58 5 4 Cleaning the thermal print head eee eee 59 5 5 Adjusting the balance and print head tensiON
19. EZ2000 Plus EZ6000 Plus User Manual 4 M a a a Printer Language Ferri Godex Eltron Printer Language GZPL Godex Zebra Printer Label design software QLabel IV for EZPL only Driver amp DLL Windows 2000 XP and Vista Bitmap fonts 6 8 10 12 14 18 24 30 16X26 and OCRA amp B Bitmap fonts 90 180 270 rotatable single characters 90 180 270 Resident Fonts rotatable Bitmap fonts 8 times expandable in horizontal and vertical directions Scalable fonts 90 180 270 rotatable Bitmap fonts 90 180 270 rotatable single characters 90 180 270 rotatable Download Fonts Asian fonts 90 180 270 rotatable and 8 times expandable in horizontal and vertical directions Scalable fonts 90 180 270 rotatable 1 D Bar codes Code 39 Code 93 Code 128 subset A B C UCC EAN 128 K Mart UCC EAN 128 UPC A E add on 2 amp 5 2 of 5 2 of 5 with Shipping Bearer Bars EAN 8 13 add on 2 5 Codabar Post NET EAN 128 DUN 14 HIBC MSI 1 Mod 10 Random Weight Telepen FIM China Postal Code RPS 128 Barcodes and GS1 DataBar 2 D Bar codes PDF417 Datamatrix code MaxiCode QR code and Micro QR code CODEPAGE 437 850 851 852 855 857 860 861 862 863 865 866 869 137 Code Pages WINDOWS 1250 1251 1252 1253 1254 1255 Unicode UTF8 UTF16 downloadable from the software Serial port RS 232 DB 9 USB port default on CF Card socket Ethernet
20. Installation of the rewinder guide is now complete Now load the label stock Pass the label stock through the rewinder from the bottom up Secure the label stock on the rewinder using the retention clip Note Make sure you choose the correct rewind direction Close the printer cover to complete the installation Note 1 Before you start using the rewinder please make sure that you have carried out all the steps as shown in the illustrations Note 2 To use the label dispenser you have to remove the rewinder guide again EZ2000 Plus EZ6000 Plus User Manual 36 e 3 Label dispenser EZ2000 Plus Unscrew the screw marked in the illustration on the front of the printer which secures the lower cover plate Remove the lower cover plate Note Switch off the printer before Starting the installation Place the printer the right way up again Pull out the print head release lever as shown in the illustration 1 and turn it anticlockwise to a top right position 2 Remove the retention clip Now load the label roll into the printer Note A label liner thickness of 0 06 mm 10 a weight of 65 g ni 6 and a label height of 20 mm are recommended Suggestion When using the label dispenser you should set the stop position to 12 mm Strip a few labels off the label liner approx 400 m Then pass the label liner through the print mechanism and from the bottom up onto the re
21. Rewinder full cable underneath the belt to avoid possible faults Now replace the power supply unit and connect it to the motherboard Replace the left hand part of the printer housing and secure it with screws Remove the lower cover plate from the front of the printer by unscrewing the screw marked in the illustration Remove the lower cover plate Mount the rewinder guide on the print mechanism and secure it with SCrews EZ2000 Plus EZ6000 Plus User Manual 42 Now load the label stock Pass the label stock through the rewinder from the bottom up Secure the label stock on the rewinder using the retention clip Note Make sure you choose the correct rewind direction 29 Replace the printer cover to complete the installation Note 1 Before you start using the rewinder please make sure that you have carried out all steps as shown in the illustrations Then send the command AXSET REWINDER 1 to the printer to enable the rewind function Note 2 To use the label dispenser you have to remove the rewinder guide again EZ2000 Plus EZ6000 Plus User Manual 43 4 5 Installing the label dispenser EZ6000 Plus with rewinder Cable clips set of 2 Screws set of 2 Note For EZ 6200 Plus the printing soeed will be limited to 4 IPS when the rewinder or label dispenser is enabled Unscrew the screw marked in the illustration on the front of the printer which secures the lower cover plate
22. Search Address V Printers and Faxes Printer Tasks 2 Printers and Faxes File Edit View Favorites Tools Help Add a printer So Set up Faxing EZ2000 Plus EZ6000 Plus User Manual 19 2 Operator panel 3 1 Operator panel introduction ia PAUSE LED LED indicators E fan RIBBON MEDIA The POWER Ready LED lights up when the printer POWER has started up and is ready FEED I PAUSE CANCEL to print 0 RIBBON Ribbon status indicator MEDIA Media status indicator 3 2 Function buttons introduction FEED button When you press the FEED button the printer moves the label to the defined stop position If you are using continuous labels pressing the FEED button will move label stock until you release the button again If you are using individual labels pressing the FEED button will move only one label If the label does not stop at the correct position you need to run the auto detection function on the label stock see Section 3 6 I PAUSE button Pressing the PAUSE button while the printer is in standby mode will set the printer to pause mode The message Pause is shown on the LCD display In this mode the printer can receive commands but it can only process them when it is reset to standby mode Pressing the PAUSE button again will reset the printer to standby mode Pressing the PAUSE button during printing will interrupt printing When the PAUSE button is pressed again the print
23. User Manual E2000 Plus E76000 Plus P N 920 011911 05 1 FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a CLASS A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at own expense EMS AND EMI COMPLIANCE STATEMENT FOR EUROPEAN USERS This equipment has been tested and passed with the requirements relating to electromagnetic compatibility based on the standards EN 55022 1998 A1 2000 A2 2003 CISPR 22 Class A EN 55024 1998 A1 2001 A2 2003 IEC 61000 4 Series EN 61000 3 2 2000 amp EN 61000 3 3 1995 The equipment has also been tested and passed in accordance with the European otandard EN55022 for the both Radiated and Conducted emissions limits EZ PLUS SERIES TO WHICH THIS DECLARATION RELATES IS IN CONFORMITY WITH THE FOLLOWING STANDARDS EN55022 1998 CLSPR 22 Class A EN55024 1998IEC 61000 4 Serial EN61000 3 2 2000 EN 6100 3 3 1995 CFR 47 Part 1
24. ard or the FEED button on the printer when the message Exit keyboard mode Y N appears on the display To switch back to keyboard mode either start up the printer again or select Keyboard mode in settings mode If you wish to make any changes to the keyboard settings please refer to the Settings diagram in Section 3 3 Printing a stored label in keyboard mode Product name Price Serial Number At least one form must be stored in the printer To create a sample label as shown above copy the commands in the left hand column and send them to m the printer using QLabel or C0 00001 1 Serial Number HyperTerminal V00 16 Product Name jcO V01 16 Price jcO The sample form contains 2 variables AF 330 566 1 1 0 0 C0 and a serial number Product name AH 212 168 1 1 0 0 V00 Price and Serial Number Printing E 1 0 0 V01 will start only when values have been set for all 3 variables owitch off the printer connect the PS 2 keyboard to the PS 2 printer port and switch the printer on again Press ENTER to switch to keyboard mode 5 Press ENTER to select a file Note Press tor to select the previous or next form in the list EZ2000 Plus EZ6000 Plus User Manual 29 EZ2000 Plus EZ6000 Plus User Manual 30 The input form for the serial number is now shown on the display Specify a start value example 00001 The input form for the first variable is now shown on the display opecify a
25. bels on label liner or labels with tag holes Continuous medium For continuous label stock Baud rate Default 9600 bps bits per second 4800 bps 9600 bps 19200 bps 38400 bps 57600 bps 115200 bps Parity Default None RS232 serial settings None Odd Even Data length Default 8 bits 7 bits 8 bits Stop bit Default 1 bit 1 bit 2 bits Default Automatic Automatic Automatic detection of label type labels with black marks die cut labels or continuous label stock and label height Gap mode For die cut labels on label liner or labels with tag holes Reflective mode For labels or normal paper with black Accessories options Paper settings Sensor type marks on the reverse side EZ2000 Plus EZ6000 Plus User Manual 23 Default English English oimplified Chinese Traditional Chinese LCD language Spanish Italian German French Turkish Default Code page 850 Code page 850 Code page 852 Code page 437 Code page 860 Code page 863 Code page 865 Code page 857 Code page 861 Code page 862 Code pages installed Code page 855 Code page 866 Code page 737 Code page 851 Code page 869 Windows 1252 Windows 1250 Windows 1251 Windows 1253 Windows 1254 Windows 1255 Default US US International English UK French German Spanish Italian Finnish Dutch Flemish Retrieve label Retrieval of a label from the memory Keyboard layout Layout of the keyboard Code page setting Code page setting Print option Pri
26. ck the software settings driver settings or command codes One or both LEDs light up red Look for the error alert in the table in Section 3 8 and printing is interrupted Error alerts Check whether the cutter is functioning normally and whether it is cutting at all Only if a cutter is installed The label stock passes through Please make sure that the label stock is loaded the the printer but no image is right way up and that it is suitable material printed Please make sure that the ribbon is loaded correctly Clear the paper jam Remove any label material left on the thermal print head and clean the print head using a soft lint free cloth dipped in alcohol Check the thermal print head for dust or other dirt label material or ribbon residue Check for errors in the application software There is no printed image on Check the ribbon for wrinkles part of the label or the image is Check the power supply blurred Run a self test Section 3 4 and check the test print pattern to see whether the print head prints over the entire width of the medium Check the quality of the print medium Run the auto detection function Section 3 6 The printed image is positioned Check the label height setting incorrectly or a label is missed Check whether there is paper or dust covering the out during printing Sensor Check the paper guide settings labels in a straight line labels completely When using the cutter the Check w
27. ead should be cleaned once a week Note 27 Please make sure that there are no metal fragments or other hard particles on the soft cloth used to clean the print head EZ2000 Plus EZ6000 Plus User Manual 59 5 5 Adjusting the balance and print head tension Open the printer side cover Pull out the print head release lever as shown in the illustration 1 and turn it anticlockwise to a top right position 2 When using a variety of label stock and ribbons the ink may not be ERU evenly distributed If there is no ST ps printed image on one side of the i paper or the ribbon wrinkles the print head pressure must be readjusted using the TPH spring boxes aS BE AN 3 Move the TPH spring boxes as shown in the illustration to change the print head pressure The wider the medium you are using the further out the TPH spring boxes must be moved If there is no quality improvement you need to change the pressure on the TPH spring boxes Turning the screw clockwise increases the pressure while turning it anticlockwise reduces the pressure EZ2000 Plus EZ6000 Plus User Manual 60 5 6 Ribbon shield settings The use of different ribbon materials may cause wrinkling of the ribbon which in turn affects the print result as illustrated by the examples in a and b To change the print quality you can adjust the ribbon shield screws If your print result looks like the example in a you need to tur
28. er resumes printing Example While a 10 label print job is running you press the PAUSE button to pause the printer Two of the labels have been printed To resume printing and print the remaining eight labels you press the PAUSE button again CANCEL button Pressing the CANCEL button during printing cancels a print job The message Print job cancelled is shown on the LCD display The current print job is cancelled Example While a 10 label print job is running you press the CANCEL button Two of the labels have been printed The print job is cancelled and the remaining eight labels are not printed EZ2000 Plus EZ6000 Plus User Manual 20 You can combine the FEED PAUSE and CANCEL buttons in a number of ways to perform different printer functions Button Beeps LCD display Function gt Switch on the printer and keep Self test O Power 3 beeps self test the gt button pressed until you hear 3 beeps 3 Dum Now in Dump After the self test keep the iua gt Power beeps gt Mode button pressed until you hear a On 1 beep beep Switch on the printer and keep Auto Il Power Auto Sensing n UE on the printer and keep Factory gt i 2x2 Coto detad i the and buttons settings Power On beeps pressed until you hear 2 beeps d This resets the printer to the factory settings Switch on the printer and keep Download Power 1 beep DL Mode Vx xx the L button pressed until you mode On hear a bee
29. he adjustable paper guide Note Pass the labels through the printer as shown in the illustration 10 Return the print head release lever to its original position Then close the printer cover EZ2000 Plus EZ6000 Plus User Manual 15 2 2 Loading the ribbon Place the printer on a flat surface and open the printer cover Pull out the print head release lever as shown in the illustration 1 and turn it anticlockwise to a top right position 2 Place a new ribbon on the ribbon supply hub Then place an empty ribbon core on the ribbon rewind hub The two illustrations on the right show you how to install the ribbon depending on the ribbon type ink side in or out Pass the ribbon under the print head and back up on the other side Attach it to the empty ribbon core Note Do not pass the ribbon under the sensor EZ2000 Plus EZ6000 Plus User Manual 16 2 3 Connecting the printer to the host computer Please make sure that the printer is switched off Connect the power cord to the AC adapter and connect the adapter to the printer Connect the USB cable to the printer and host computer Switch on the printer The operator panel should now light up pP us EZ2000 Plus EZ6000 Plus User Manual 17 2 4 Installing the driver 1 Insert the product CD in the CD DVD drive of the host computer and open the Windows Drivers folder on the CD Select the icon for the driver
30. hether the cutter has been correctly installed labels are not fed through or cut Check whether the paper guides are functioning off incorrectly correctly The label dispenser is not Check whether there is dust on the label dispenser functioning normally Check whether the label stock is positioned correctly Note J If any problems occur that are not described here please contact your dealer The label stock jams during printing EZ2000 Plus EZ6000 Plus User Manual 63
31. ibbon only thermal paper printing DTP Please check which printing method you are using and alter the settings accordingly in the printer driver printer menu and or software 2 1 Loading the label roll Place the printer on a flat surface and open the printer cover Pull out the print head release lever as shown in the illustration 1 and turn it anticlockwise to a top right position 2 Pull the release catch for the label roll guide to the right as shown by the blue arrow 1 Now slide the label roll guide forward and fold it up as shown by the blue arrow 2 EZ2000 Plus EZ6000 Plus User Manual 13 Place the label roll on the label supply hub pushing it right up to the printer housing Do not apply too much pressure to avoid damaging the label stock Fold the label roll guide back down and push it against the label roll Note When moving the label roll guide hold it only by the end that is attached to the bracket not by its top Load the label roll into the printer as shown in the illustration Pass it through the printer as indicated by the blue arrows Pass the label stock through the sensor and up to the tear off plate Note Remember to set the movable sensor to gap black mark or tag hole by changing the position of the sensor with the adjustment wheel EZ2000 Plus EZ6000 Plus User Manual 14 The labels pass between the wall of the printer housing and t
32. in Mini Din Jack 1 gt Black 2 Brown 3 gt Red 4 Orange 5 gt Yellow 6 gt Green 7 gt Blue 8 Purple ADD DBRINTIN 4 ADD DRIN ADD DIO Housing 2 00 5x2 EZ2000 Plus EZ6000 Plus User Manual 10 1 4 Getting to know your printer External view A Operator panel with LCD display Lower cover plate Viewing window Printer cover Eh OMN O ONO Ol 12 1 Feed slot for continuous labels He CF card slot 4 Parallel port optional 4 WLAN antenna interface optional 5 Ethernet port 6 Serial port DB 9 L0 4 8 Appliatorinterface optiona 1 1 9 USBpot 3 10 On Off swith 10 Feed slot for continuous labels EZ2000 Plus EZ6000 Plus User Manual 11 Internal view 12 11 1 gt 10 3 4 5 9 6 8 7 Ribbon rewind hub Ribbon supply hub Print mechanism 6 Release lever for printhead 0 9 Labeltensionguide 0 eee ph RB wd NUR RUE ees ee SE Movable sensor EZ2000 Plus EZ6000 Plus User Manual 12 2 Printer setup This printer supports the following printing methods Thermal transfer Requires a ribbon for transferring a printed image to a medium printing TTP Direct thermal Does not require a r
33. n ribbon shield screw A clockwise If your print result looks like the example in b you need to turn ribbon shield screw B clockwise TA TEST Ml COMPANY NAME SAMPLE IN 1234567890 a LABEL TEST ANTI VTL COM PANY NAME SAMPLE gil TT 1 234567890 b 2 Tokeep track of the change in print quality you should adjust the screws by half a turn at a time Print a test page If there is no improvement in the print result turn the screw by another half turn Do not turn the adjustment screw more than two full turns Note If you adjust the screw by more than two full turns the paper feed may no longer function correctly In that case unscrew the ribbon shield screws fully and restart the adjustment process EZ2000 Plus EZ6000 Plus User Manual 61 5 7 Cutter settings Socket head screws for adjusting the cutter are located on both sides of the cutter In the event of a paper jam the cutter will no longer function correctly Switch off the printer and use a hex key M3 to turn the socket head screw Turn the key anticlockwise to remove the jammed paper When you have removed the jammed paper you can switch the printer back on The cutter will automatically reset Note The label medium should be at least 30 mm long to ensure correct functioning of the cutter EZ2000 Plus EZ6000 Plus User Manual 62 5 8 Troubleshooting Problem the display does not light up Che
34. ng Connect the applicator cable to the jack marked APP on the motherboard Secure the applicator interface using two SCrews Replace the left hand part of the printer housing and secure it with the screws you removed earlier to complete the installation EZ2000 Plus EZ6000 Plus User Manual 52 Installing the WLAN module EZ2000 Plus EZ6000 Plus 4 9 Ethernet cable 1 8 m Fastening screws set of 2 Screws for Ethernet module set of 2 WLAN module 7 10 le Connection cable module to motherboard 7 WLANantenna 8 Nut 9 10 Antenna bracket Make sure that the printer is switched off and the power cord disconnected from the printer Place the printer on a clean flat surface and open the printer cover Remove the left hand part of the printer housing Remove the covers from the network interface and antenna jack Secure the Ethernet module on the bracket Now plug the cable connector into the network card socket EZ2000 Plus EZ6000 Plus User Manual 53 Plug the other end of the connection cable into the motherboard socket Secure the module bracket on the inside of the printer housing at the back Push the antenna connector through the antenna bracket Attach the antenna bracket to the back of the printer EZ2000 Plus EZ6000 Plus User Manual 54 10 Putthe washer on the antenna connector and secure the connector on the antenna bracket using
35. nt quantity setting ey pearl mods Clock setup Sets the time on the clock shown on the display Exit keyboard mode Resets the printer to normal mode and ready to receive print jobs from the host computer Keyboard layout Default ON ON Switches beep signals on or off OFF No backfeed ON This function requires a dispenser or cutter OFF Default OFF password ON When password protection is enabled you need a password to access the settings OFF Default ON ON Always starts printing at the top of the page OFF EZ2000 Plus EZ6000 Plus User Manual 24 Default USB Ethernet Enables the Ethernet ee Lets you preview and check the settings Locks the value s of any setting When a value is locked it cannot be altered by changes to the driver or by sending a command You can lock the following values EVERYTHING locks all values DARKNESS SPEED STOP POS AD STOP POS PRINTHEAD POS Lock setup PRINTING MODE OPTION SETUP SENSOR SETUP COMPORT SETUP AUTO SENSOR LCD LANGUAGE CODEPAGE KEYBOARD BUZZER SMART BACKFEED TOP OF FORM Note 1 The default settings are the original factory settings If you have changed the settings your current settings will be displayed in settings mode Note 27 The printer will store your changes even after it is switched off You can change the settings again in settings mode EZ2000 Plus EZ6000 Plus User Manual 25 Settings mode diagram Darkness Speed
36. o Linefeed Computer printer Computer Printer Printer Printer Printer Computer printer N C oignal Gnd Chassis Gnd 5V max 500mA Signal Gnd Initialize Error Signal Ground N C Select in Computer Computer printer Printer Computer printer Serial port Default Baud rate 9600 no parity 8 data bits 1 stop bit XON XOFF protocol and settings RTS CTS RS232 housing DB9 ae SO DB9 plug 45V max 500mA TXD c co JO Ci ON Computer Printer Note The total current to the parallel and serial ports may not exceed 500 mA EZ2000 Plus EZ6000 Plus User Manual 8 USB port Connector type Pin No Function PS 2 port Pin No pt ft 2 fe a 5 Function PS 2 computer to printer interface Printer DATA N C Bb U N Bss O OO C1 O Internal interface UART1 wafer E O U N X RXD CTS GND T CO i O A lt U lt N RTS E RST 5 GND 5 cO CO OD O D o IGO ON O 010 A G N i e aL N O UART2 wafer JJ lt gt U G N CD K JJ Y Cp CO z 3 2 O OD o Y O lx Ix noil o 0O 0 JO 0 A O N EZ2000 Plus EZ6000 Plus User Manual 2 3 Add on module Applicator wafer Printing out Print error out Printed out Applicator module 5V AAA MM D Print in GND N C GND O IO O JO GQ E O M 7P
37. o format the CF card press the CANCEL button 5 Once formatting is complete a folder Godex is created This folder including its content formats images and fonts is managed by the printer Do not edit it manually 6 Thefollowing CF cards are supported CompactFlash Type I CompactFlash CF v1 4 specification Capacity 128 MB 1 GB File system FAT16 EZ2000 Plus EZ6000 Plus User Manual 33 4 Accessories 4 1 Internal rewinder EZ2000 Plus Note Maximum height of the rewound medium 118 mm Suggestion Medium thickness 0 06 mm 0 25 mm Place the printer on a flat surface and open the printer cover Note Hemember to switch off the printer before starting the installation Remove the cover for the rewinder module EZ2000 Plus EZ6000 Plus User Manual 34 Remove the retention clip from the rewinder Secure the rewinder on the printer housing using the four screws supplied Now connect the rewinder cable to the printer housing Installation of the rewinder module is now complete EZ2000 Plus EZ6000 Plus User Manual 35 7 2 Installing the rewinder guide EZ2000 os Unscrew the screw marked in the ed illustration on the front of the printer which secures the lower cover plate 2 Remove the lower cover plate Note Switch off the printer before starting the installation Mount the rewinder guide on the print mechanism and secure it with SCrews
38. or anticlockwise as required G Qutside ene Ir Increasing the tension of the ribbon rewind hub will remove any wrinkling of the ribbon during printing which results from the use of different ribbon materials For details about the wrinkling creasing of ribbons see Section 5 6 If you are using a very narrow ribbon the printer may not move the label stock forward particularly with a ribbon that is less than 2 wide In that case reduce the tension by turning the knob of the ribbon supply hub anticlockwise If the tension is too high the ribbon core may be crushed and thus impossible to remove In that case reduce the tension of the ribbon supply hub and the ribbon rewind hub by turning the knobs anticlockwise EZ2000 Plus EZ6000 Plus User Manual 58 5 4 Cleaning the thermal print head Dirt on the print head or ribbon may result in inadequate print quality no printed image on part of the label The printer cover should therefore be kept closed whenever possible Keeping dirt and dust away from the paper or labels ensures a good print quality and a longer lifespan of the print head Here is how you clean the print head Switch off the printer Open the printer cover Remove the ribbon Release the print head by turning the print head release lever To remove any label residue or other dirt from the print head see blue arrow please use a soft lint free cloth dipped in alcohol Note 1 The print h
39. p This mode is for download of the firmware only Switch on the printer and keep Settings 3 beeps Setting mode the button pressed for about mode 3 4 seconds until you hear 3 beeps EZ2000 Plus EZ6000 Plus User Manual 21 3 3 Settings mode In settings mode you can change different settings such as the printing mode accessories options or media type 1 Switch on the printer and make sure that the message Ready is shown on the display 2 Press the PAUSE button and keep it pressed for about 3 4 seconds until you hear 3 beeps and the message Settings is shown on the display 3 ln settings mode the buttons have the following functions Minus Enter Menu Next Plus Exit t II 4 Before you exit settings mode the printer will prompt you to save the changes you have made Once you have saved or discarded your changes the printer will switch back to standby mode Press the button and keep it pressed for about 3 4 seconds until you hear 3 beeps and the message Settings is shown on the display The options available are shown in the lower section of the display LCD Language Enter Exit LCD Language Enter Next EZ2000 Plus EZ6000 Plus User Manual In settings mode the first line always shows the name of a setting the second line the current selection or value To change the current selection or value press the ENTER button The current selection or value is highligh
40. r another port type not listed below create a new port Tvpe Serial Port 9600 91 Local Pork Virtual printer port for USE USBO02 Virtual printer port for LISB IP 192 168 1 7 Standard TCP IP Port 192 168 1 7 LPR Create Port Configure Part Enter a printer name and mU assign the appropriate rights Specify Printer Name Names are used to identify the printer on this computer and an the network Enter a name For this printer Printer name Use this printer as the default printer Specify whether or not you want to share this printer with other network users When sharing vou must provide a share name 2 Do not share this printer Once the installation is mE complete a summary of the printer setti ngs is displayed Names are used to identify the printer on this computer and an Ehe network Specify Printer Name Check whether the printer Enter a name Far this printer settings are correct and click Finish to start copying the d river fi les Use this printer as the default printer Printer name EI Ex rU RE Specify whether or not vau want to share this printer with other network users When Wait u ntil copyi ng IS sharing vou must provide a share name com plete then finish the e Do nat share this printer aries gece EAS Once the driver installation is complete the new printer should be visible in the EF Printers and Faxes folder wy gt E amp 89 B Lp Cut Copy Paste
41. stalling the cutter Cable clips Note 1 Remember to switch off the printer before installing the cutter Note 2 Do not use to cut adhesive labels Glue residue will be left on the cutter blade and impair its functioning The cutter has a blade life of 500 000 cuts when using paper weighing 160 g m and 250 000 cuts when using paper weighing 200 g m Unscrew the screw marked in the illustration on the front of the printer which secures the lower cover plate 2 Remove the lower cover plate Note Switch off the printer before starting the installation Remove the two screws securing the tear off plate then remove the tear off plate EZ2000 Plus EZ6000 Plus User Manual 47 Secure the cutter module on the printer housing using the screws Connect the cutter cable connector to the cutter jack on the printer Route the connection cable along the bottom of the printer housing using the cable clips Place the cutter cover over the cutter module and secure it using the screw you removed from the lower cover plate Now load the label roll into the printer and close the printer cover Note 1 Check whether the cutter function is enabled in the printer Note 2 Labels or paper should be at least 30 mm high Suggestion After installation of the cutter module set the stop position to 26 mm EZ2000 Plus or 30 mm EZ6000 Plus EZ2000 Plus EZ6000 Plus User Manual i k
42. ted When you change a setting the first line shows the name of the setting the second line the current selection Plus The button increases the value Minus The button reduces the value Next The button switches to the next settings option The following table lists descriptions of the available settings and options Default 10 Sets the temperature during printing Values range from O to 19 the default setting is 10 Sets the print speed inches per second ips Default 12 Stop position The stop position determines how far the printed label is moved out tear off position cut off position Default 0 Adjusts the printer s stop position Values range from 0 to 10 This value changes the stop position irrespective of the driver or software settings Default 0 Vertical position Sets the 0 position of the print head Values range from 100 to 100 Default Thermal transfer Adjust stop position Thermal transfer Requires a ribbon to transfer a printed Printing mode image to a label Direct thermal No ribbon is required for printing but a direct thermal print medium must be loaded Default Option disabled Dispenser mode Select to enable the dispenser mode Cutter mode Select to enable the cutter mode Option disabled Select this setting to disable both options Default Die cut labels Black marks For labels or normal paper with black marks on the reverse side Die cut labels For die cut la
43. winder EZ2000 Plus EZ6000 Plus User Manual 37 Wind the label liner around the rewinder and secure it using the retention clip Return the print head release lever to its original position Note Please make sure that the label stock rewinds the right way onto the rewind hub Replace the lower cover plate on the printer and secure it with screws Press the lower part of the stripper sensor to fold it out The sensor locks ina horizontal position Close the printer cover to complete installation of the dispenser EZ2000 Plus EZ6000 Plus User Manual 38 4 4 Internal rewinder for EZ6000 Plus For EZ 6200 Plus the printing speed will be limited to 4 IPS when the rewinder or label dispenser is enabled Place the printer on a flat surface and open the printer cover Remove the screws securing the left hand part of the housing and the printer cover and remove these two parts of the housing Note Remember to switch off the printer before starting the installation Remove the connectors from the power supply unit in the two places marked Remove the two screws that secure the power supply unit on the bottom of the printer housing Remove the power supply unit Remove the cable connecting the motherboard and the connector bracket EZ2000 Plus EZ6000 Plus User Manual 39 Remove the two screws securing the connector bracket from the inside of
44. xit dump mode 3 6 Label size calibration The printer can automatically detect and store label height That means the host computer does not need to transmit the label height to the printer 1 Check that the label sensor is positioned correctly 2 Switch off the printer 3 owitch on the printer keeping the PAUSE button pressed When you hear 3 beeps and the message Auto Sensing Mode appears on the display release the PAUSE button The printer will now automatically measure the label size and store this information 4 Thelabel height in mm is shown on the display After displaying the label height the printer switches back to standby mode EZ2000 Plus EZ6000 Plus User Manual 28 3 7 Keyboard mode The printers of the EZ2000 Plus and EZ6000 Plus series support keyboards with a PS 2 interface provided the parallel PS 2 adapter is installed Here is how you connect a PS 2 keyboard 1 Switch off the printer and plug the PS 2 connector into the appropriate printer port 2 Switch on the printer The message Keyboard mode Y N is shown on the display Press the FEED button on the printer or the ENTER key on the keyboard to switch to keyboard mode In keyboard mode you can go back to the previous page at any time by pressing the ESC key on the keyboard or the CANCEL button on the printer If you keep going back you will eventually be prompted to exit keyboard mode To exit keyboard mode press the ENTER key on the keybo
Download Pdf Manuals
Related Search