Metra XSVI-6522-NAV car kit
Contents
1. XSVI 652e2 NAV INSTALLATION INSTRUCTIONS NOTE ASWC SOLD SEPERATELY In the Chrysler vehicles listed on back there are no 12 volt accessory wires in the factory radio harness making the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 6522 NAV is designed to provide a 12 volt 10 amp switched accessory output along with the rest of the wires needed to install an aftermar ket radio The R A P Retained Accessory Power function is retained by the XSVI 6522 NAV Along with OE equipped steering wheel controls using the steering wheel control output of the aftermarket radio if equipped The XSVI 6522 NAV also provides essential wires required for aftermarket ra dios that have navigation Provided is VSS Vehicle Speed Sense Reverse and Parking Brake This cuts down the installation time since the installer does not have to look for these wires in the vehicle Note The XSVI 6522 NAV does not retain OEM amplifiers Wiring the XSVI 6522 NAV Wiring up the XSVI 6522 NAV is like wiring up any other wire harness that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio Navigation wire colors Blue Pink VSS Vehicle Speed Sense Green Violet Reverse Lt Green Parking Brake Once all connections have been made plug in the afterma2. 0 e CHALLENGER 2009 UP e CHARGER 2008 2010 e DAKOTA 2008 UP e DURANGO 2008 UP e GRAND CARAVAN 2008 10 e JOURNEY 2009 2010 e MAGNUM 2008 10 e NITRO 2007 UP e RAM 1500 2009 UP e RAM 2500 3500 2011 UP JEEP e COMMANDER 2008 2010 e COMPASS 2009 UP e GRAND CHEROKEE 2008 2011 LIBERTY 2008 UP e PATRIOT 2009 2010 e WRANGLER 2007 UP INSTXSVI 6522 NAV REV 03 17 11 1 800 221 0932 www metraonline com METRA ELECTRONICS CORPORATION COPYRIGHT 2010 APPLICATIONS CHRYSLER e 200 2011 e 300 2008 2010 e ASPEN 2008 2009 e SEBRING 2007 2010 e TOWN amp COUNTRY 2008 UP DODGE e AVENGER 2008 UP e CALIBER 2009 10 e CHALLENGER 2009 UP e CHARGER 2008 2010 e DAKOTA 2008 UP e DURANGO 2008 UP e GRAND CARAVAN 2008 10 e JOURNEY 2009 2010 e MAGNUM 2008 10 e NITRO 2007 UP e RAM 1500 2009 UP e RAM 2500 3500 2011 UP JEEP e COMMANDER 2008 2010 e COMPASS 2009 UP e GRAND CHEROKEE 2008 2011 e LIBERTY 2008 UP e PATRIOT 2009 2010 e WRANGLER 2007 UP INSTXSVI 6522 NAV REV 03 17 11 1 800 221 0932 www metraonline com METRA ELECTRONICS CORPORATION COPYRIGHT 2010 XSVI 652e2 NAV INSTALLATION INSTRUCTIONS NOTE ASWC SOLD SEPERATELY In the Chrysler vehicles listed on back there are no 12 volt accessory wires in the factory radio harness making the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 6522 NAV is designed to prov
3. APPLICATIONS CHRYSLER e 200 2011 e 300 2008 2010 e ASPEN 2008 2009 e SEBRING 2007 2010 TOWN amp COUNTRY 2008 UP DODGE e AVENGER 2008 UP e CALIBER 2009 10 e CHALLENGER 2009 UP e CHARGER 2008 2010 e DAKOTA 2008 UP DURANGO 2008 UP e GRAND CARAVAN 2008 10 e JOURNEY 2009 2010 e MAGNUM 2008 10 e NITRO 2007 UP e RAM 1500 2009 UP e RAM 2500 3500 2011 UP JEEP e COMMANDER 2008 2010 e COMPASS 2009 UP e GRAND CHEROKEE 2008 2011 LIBERTY 2008 UP e PATRIOT 2009 2010 e WRANGLER 2007 UP INSTXSVI 6522 NAV REV 03 17 11 1 800 221 0932 www metraonline com METRA ELECTRONICS CORPORATION COPYRIGHT 2010 APPLICATIONS CHRYSLER e 200 2011 e 300 2008 2010 e ASPEN 2008 2009 e SEBRING 2007 2010 e TOWN amp COUNTRY 2008 UP DODGE e AVENGER 2008 UP e CALIBER 2009 10 e CHALLENGER 2009 UP e CHARGER 2008 2010 e DAKOTA 2008 UP e DURANGO 2008 UP e GRAND CARAVAN 2008 10 e JOURNEY 2009 2010 e MAGNUM 2008 10 e NITRO 2007 UP e RAM 1500 2009 UP e RAM 2500 3500 2011 UP JEEP e COMMANDER 2008 2010 e COMPASS 2009 UP e GRAND CHEROKEE 2008 2011 e LIBERTY 2008 UP e PATRIOT 2009 2010 e WRANGLER 2007 UP INSTXSVI 6522 NAV REV 03 17 11 1 800 221 0932 www metraonline com METRA ELECTRONICS CORPORATION COPYRIGHT 2010 APPLICATIONS CHRYSLER e 200 2011 e 300 2008 2010 e ASPEN 2008 2009 e SEBRING 2007 2010 TOWN amp COUNTRY 2008 UP DODGE e AVENGER 2008 UP e CALIBER 2009 1
4. ide a 12 volt 10 amp switched accessory output along with the rest of the wires needed to install an aftermar ket radio The R A P Retained Accessory Power function is retained by the XSVI 6522 NAV Along with OE equipped steering wheel controls using the steering wheel control output of the aftermarket radio if equipped The XSVI 6522 NAV also provides essential wires required for aftermarket ra dios that have navigation Provided is VSS Vehicle Speed Sense Reverse and Parking Brake This cuts down the installation time since the installer does not have to look for these wires in the vehicle Note The XSVI 6522 NAV does not retain OEM amplifiers Wiring the XSVI 6522 NAV Wiring up the XSVI 6522 NAV is like wiring up any other wire harness that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio Navigation wire colors Blue Pink VSS Vehicle Speed Sense Green Violet Reverse Lt Green Parking Brake Once all connections have been made plug in the aftermarket radio if not done already Do not plug in the ASWC into the XSVI harness yet Initialize the XSVI interface With all connections made and harnesses connected to the vehicle turn the ignition key to the ON position for thirty seconds then turn the key off After the XSVI is initialized plug in the ASWC and refer to the ASWC instructions
5. navigation Provided is VSS Vehicle Speed Sense Reverse and Parking Brake This cuts down the installation time since the installer does not have to look for these wires in the vehicle Note The XSVI 6522 NAV does not retain OEM amplifiers Wiring the XSVI 6522 NAV Wiring up the XSVI 6522 NAV is like wiring up any other wire harness that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio Navigation wire colors Blue Pink VSS Vehicle Speed Sense Green Violet Reverse Lt Green Parking Brake Once all connections have been made plug in the aftermarket radio if not done already Do not plug in the ASWC into the XSVI harness yet Initialize the XSVI interface With all connections made and harnesses connected to the vehicle turn the ignition key to the ON position for thirty seconds then turn the key off After the XSV is initialized plug in the ASWC and refer to the ASWC instructions
6. rket radio if not done already Do not plug in the ASWC into the XSVI harness yet Initialize the XSVI interface With all connections made and harnesses connected to the vehicle turn the ignition key to the ON position for thirty seconds then turn the key off After the XSV is initialized plug in the ASWC and refer to the ASWC instructions XSVI 6522 NAV INSTALLATION INSTRUCTIONS NOTE ASWC SOLD SEPERATELY In the Chrysler vehicles listed on back there are no 12 volt accessory wires in the factory radio harness making the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 6522 NAV is designed to provide a 12 volt 10 amp switched accessory output along with the rest of the wires needed to install an aftermar ket radio The R A P Retained Accessory Power function is retained by the XSVI 6522 NAV Along with OE equipped steering wheel controls using the steering wheel control output of the aftermarket radio if equipped The XSVI 6522 NAV also provides essential wires required for aftermarket ra dios that have navigation Provided is VSS Vehicle Speed Sense Reverse and Parking Brake This cuts down the installation time since the installer does not have to look for these wires in the vehicle Note The XSVI 6522 NAV does not retain OEM amplifiers Wiring the XSVI 6522 NAV Wiring up the XSVI 6522 NAV is like wiring up any other wire harness that wo
7. uld attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio Navigation wire colors Blue Pink VSS Vehicle Speed Sense Green Violet Reverse Lt Green Parking Brake Once all connections have been made plug in the aftermarket radio if not done already Do not plug in the ASWC into the XSVI harness yet Initialize the XSVI interface With all connections made and harnesses connected to the vehicle turn the ignition key to the ON position for thirty seconds then turn the key off After the XSV is initialized plug in the ASWC and refer to the ASWC instructions XSVI 652e2 NAV INSTALLATION INSTRUCTIONS NOTE ASWC SOLD SEPERATELY In the Chrysler vehicles listed on back there are no 12 volt accessory wires in the factory radio harness making the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 6522 NAV is designed to provide a 12 volt 10 amp switched accessory output along with the rest of the wires needed to install an aftermar ket radio The R A P Retained Accessory Power function is retained by the XSVI 6522 NAV Along with OE equipped steering wheel controls using the steering wheel control output of the aftermarket radio if equipped The XSVI 6522 NAV also provides essential wires required for aftermarket ra dios that have
Download Pdf Manuals
Related Search