Chief MAC722
Contents
1. Head Assembly Head Assembly 1 MAC722 Right Head Assembly PAC722 Right F 4 5 16 18 x 3 1 2 Installation Instructions MAC722 PAC722 Assembly and Installation The MAC722 and PAC722 side by side accessories are for use with Chief carts and stands 1 Remove and save four fasteners holding the faceplate on the cart or stand column and remove faceplate See Figure 1 6 Figure 1 2 Use the four fasteners removed in Step 1 to fasten the extension assembly A to the cart stand column See Figure 2 Qe Back of column Figure 2 Attach faceplates B and C OR D and E to the extension assembly A using two 5 16 18 x 3 1 2 button head cap screws F and two 5 16 locking nuts G for each faceplate See Figure 3 PAC722 Right Head Assembly shown Figure 3 Measure distance from center of display to outside edge Measure distance from center of faceplate to center of extension assembly A See Figure 4 Center of faceplate Measure this distance Center of extension assembly A ul N Figure 4 MAC722 PAC722 Install2. INSTALLATION INSTRUCTIONS Medium Large Side by Side Accessory for Carts and Stands CHIEF MAC722 722 Our Mounts Your Vision MAC722 PAC722 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions LEGEND CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or v
3. and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure 8 Remove pin and nut and move to lower holes A padlock or bolt may be placed through latch holes Figure 8 Tilting Display The display s can be tilted up to 59 either backward or forward from a straight upright position 1 Turn knob counterclockwise on back of faceplate to loosen the tilt See Figure 9 Place optional bolt not provided here to lock in an upright position 2 3 5 Figure 9 Tilt display as desired to a maximum of 5 either forward or backward Turn knob clockwise to tighten display on head assembly See Figure 9 A CAUTION Tighten knob on back of faceplate to prevent damage to the stand or cart If leaving the display in a straight upright position it is recommended that a bolt not provided be placed through the faceplate See Figure 9 to lock the display into the upright position Repeat Steps 1 4 for remaining faceplate and display Cable Management The display power cords can be run through the front of the extension assembly A See Figure 10 The cords can then run through the extension assembly to the center of the assembly See Figure 10 When the cords are run to the center of the extension assembly they can either exit ou
4. ation Instructions IMPORTANT In the compressed configuration the minimum display size is 38 In the extended configuration the maximum display size is 55 6 Adjust extension assembly A as necessary by removing the carriage bolt allen nut and washer on each end of the extension assembly so that distance between the center of the faceplate and center of the extension assembly matches dimension measured in Step 5 See Figure 5 WARNING IMPROPER INSTALLATION CAN LEAD TO CART STAND OR DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Extension measurement MUST be the same for both sides of the MAC722 PAC722 Two holes for full extension PAC722 shown Figure 5 Attaching Displays WARNING EXCEEDING MAXIMUM WEIGHT CAPACITY MAY LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to ensure the total amount of weight placed on the MAC722 does not exceed 125 Ibs 56 7 kg 62 5 Ibs 28 3 faceplate OR on the PAC722 does not exceed 150 Ibs 68 0 kg 75 lbs 34 0 per faceplate WARNING Before attaching displays to the MAC722 PAC722 ensure the stand or cart is on a level surface CAUTION Load displays at same time so that load MAC722 PAC722 is evenly distributed CAUTION ALWAYS remove the displays BEFORE adjusting the height of the stand or cart 1 Adjust the stand or cart to the desired height by slightly lif
5. ixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas 4 Chiave a punte aperte Steeksleutel Cl a fourche Installation Instructions MAC722 PAC722 DIMENSIONS 33 50 58 80 MAXIMUM DISPLAY WIDTH L oo U o EXTENDED CONFIGURATION pes 39 18 MINIMUM DISPLAY WIDTH COMPRESSED CONFIG URATION MAC 722 4 01 FROM FRONT 5 TILT PAC 722 FROM CART STAND FRONT 58 80 MAXIMUM DISPLAY WIDTH f T see 20 0 EXTENDED CONFIG URATIO N 14 00 39 18 14 00 MINIMUM DISPLAY WIDTH COMPRESSED CONFIG URATION MAC722 PAC722 Installation Instructions TOOLS REQUIRED FOR INSTALLATION b as 3 16 Included ff 1 2 12 7mm PARTS M 1 PAC722 Left Head Assembly MAC722 Left
6. oiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located on the accessory does not exceed MAC 722 125 Ibs 56 7 kg 62 5 Ibs 28 3 per faceplate PAC 722 150 Ibs 68 0 kg 75 Ibs 34 0 per faceplate Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Hex Head Wrench Llave de cabeza hexagonal Sechskantschlussel Chave sextavada Chiave esagonale Zeskantsleutel Cl a t te hexagonale Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar f
7. t the front or down through the cart or stand column See Figure 10 Any accessory power cords can be run through the front and down through the column See Figure 10 Figure 10 MAC722 PAC722 Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8807 002006 Rev02 2010 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 10 10 USA International Europe Asia Pacific gt 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 n O
8. ting the inner column pulling out knob on the center post and turning 90 in either direction to disengage the locking mechanism See Figure 6 Inner Column v 2 Raise or lower the center post then turn the knob 90 either direction to engage the knob and lock the stand at desired height See Figure 6 Figure 6 3 Attach interface brackets to the displays following the instructions included with the bracket 4 While supporting both sides of display align four mounting buttons on display or interface bracket with four mounting holes in head assembly See Figure 7 and See Figure 8 Figure 7 Installation Instructions MAC722 PAC722 WARNING EACH DISPLAY MAY WEIGH IN EXCESS OF 40 LBS Always use two people and proper lifting techniques when installing or positioning display on stand 5 Lower display into place listening for audible click to ensure recessed area of mounting buttons are properly seated in lower area of mounting holes See Figure 7 and See Figure 8 WARNING IMPROPER INSTALLATION CAN LEAD TO STAND OR DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Ensure mounting buttons are completely engaged in mounting holes NOTE Holes are provided in the faceplate for use with a padlock or similar locking device if desired In addition the pin
Download Pdf Manuals
Related Search