Home

Samsung 932B

1. Click the Apply button if you see the screen working normally after clicking Test If the screen is not normal change to a different mode lower mode of resolution colors or frequency If there is no Mode at All Display Modes select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide Linux Operating System is To execute X Window you need to make the X86Config file which is a type of system setting file Press Enter at the first and the second screen after executing the X86Config file The third screen is for setting your mouse Set a mouse for your computer The next screen is for selecting a keyboard Set a Keyboard for your computer The next screen is for setting your monitor First of all set a horizontal frequency for your monitor You can enter the frequency directly Set a vertical frequency for your monitor You can enter the frequency directly Enter the model name of your monitor This information will not affect the actual execution of X Window DW You have finished setting up your monitor Execute X Window after setting other requested hardware Monitor Driver Natural Color MagicTune 3 Natural Color O Natural Color Natural Color Pro color management system Monitor Color Cal amp Profiling Preference Copyright 2003 Samsung Electranics Ca Ltd One of the recent problems in using a compu
2. Do not place the monitor face down gt This may damage the TFT LCD surface The installation of the bracket must be done by a qualified professional t Installing the bracket by unqualified personnel may result in injury Always use the mounting device specified in the owner s manual When installing the product make sure to keep it away from the wall more than 10 cm 4 inches for ventilation purposes t Poor ventilation may cause an increase in the internal temperature of the product resulting in a shortened component life and degraded performance Do not disconnect the power cord while using the monitor t A surge may be caused by the separation and may damage the monitor Keep the plastic packaging bag out of children s reach The plastic packaging bag may cause suffocation if children play with it Notation Power Installation Cleaning and Use Others 3 Cleaning and Use When cleaning the monitor case or the surface of the TFT LCD screen wipe with a slightly moistened soft fabric Do not spray water or detergent directly onto the monitor This may cause damage electric shock or fire Use the recommended detergent with a smooth cloth Ifthe connector between the plug and the pin is dusty or dirty clean it properly using a dry cloth gt A dirty connector may cause electric shock or fire Make sure to unplug the power cord before cleaning the product gt Otherwise this may caus
3. 6 Movie For watching motion pictures such as a DVD or Video CD 7 Dynamic Contrast Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to create optimum contrast gt gt Click here to see an animation clip Brightness button Adjust buttons F A E Enter button SOURCE button E AUTO button Power button e Power indicator When OSD is not on the screen push the button to adjust brightness gt gt Click here to see an animation clip Adjust items in the menu Activates a highlighted menu item Push the SOURCE then selects the video signal while the OSD is off When the SOURCE button is pressed to change the input mode a message appears in the upper left of the screen displaying the current mode analog or digital input signal If you select the digital mode you must connect your monitor to the graphic card s DVI IN port using the DVI cable Use this button for auto adjustment gt gt Click here to see an animation clip Use this button for turning the monitor on and off This light glows blue during normal operation and blinks blue once as the monitor saves your adjustments See PowerSaver described in the manual for further information regarding power saving functions For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods Rear SAMSUNG The config
4. Press SOURCE button to have the monitor double check the input signal source If the initial screen the login screen appears boot the computer in the applicable mode the safe mode for Windows ME XP 2000 and then change the frequency of the video card Refer to the Preset Timing Modes If the initial screen the login screen does not appear contact the Service Center or your dealer You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly Adjust the maximum resolution and frequency that the monitor can handle properly If the display exceeds SXGA or 75 Hz a Not Optimum Mode Recommended Mode 1280 x 1024 60 Hz message is displayed If the display exceeds 85 Hz the display will work properly but the Not Optimum Mode Recommended Mode 1280 x 1024 60 Hz message appears for one minute and then disappears Please change to the recommended mode during this one minute period The message is displayed again if the system is rebooted The monitor is in PowerSaver mode Press a key on the keyboard to activate the monitor and cannot see the On Screen Display The screen shows strange colors or just black and white The screen suddenly has become unbalanced The screen is out of focus or OSD cannot be adjusted LED is blinking but no images on the screen There are only 16 colors shown on the screen T
5. Refer to the Preset Timing Modes The screen can be unbalanced due to the cycle of the video card signals Readjust Position by referring to the OSD Have you adjusted the resolution or frequency on the monitor Is the frequency properly adjusted when checking the Display Timing on the menu Have the Windows colors been set properly Has the video card been set properly Have you installed the monitor driver Adjust the resolution and frequency of the video card Refer to the Preset Timing Modes Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes The maximum frequency per resolution may differ from product to product Windows XP Set the resolution in the Control Panel gt Appearance and Themes Display Settings Windows ME 2000 Set the resolution in the Control Panel Display Settings Set the video card by referring to the video card manual Install the monitor driver according to the Driver Installation Instructions reads Unrecognized monitor Plug amp Play VESA DDC monitor found Check when MagicTune does not function properly MagicTune doesn t work properly See the video card manual to see if the Plug amp Play VESA DDC function can be supported Magic Tune feature is found only on PC VGA with Window OS that supports Plug and Play Have you changed your PC or video graphic car
6. a EATA Ee Py Mermer Dangan al Gutlook Capron h ina Pale Fria anan a kaa esa Hi Aor ad boong ne Perra sal rit jie Ls De de Se ee ee ca a ae eg ae HET 0 0 ES AA af Hokopodi is Mie Com peat er CITY Panzi ee AA Kolo and Support WD Ha Pa ET Kun Ear e A aten Pecado gt as lager ami Bryan lin a a ka a Waaa Pale asa a maana Click Display icon and choose the Settings tab then click Advanced Dit pe eg Fiap Ee Ther Bahi Damon Dawa pra Ent uras a Na di di E inr rra eee E ea dara eit Dismay Fiag med Pas Horas coe IE Pct Ni ne r Cr pasy a a P hir ipa E Higher 32 bi r OF pick a Control Panel icon gt Seen ah Aeh Plug and Play Monitor and 40 Prophet NI Properties Plug and Play Monitor Prope Y Gefoces Selection 54 Gerari Adapter Marston Troubleshoot Color Management Plug and Play Mono r Horeba bp Pua ard Plage Honor Dera peas Hin Pelican i Mieres Standard monitor hanes 0 nabingi 1 Locator on 20 Propia 11 Soren abres naka ED Heats e Devide Itala i i Tbus elsa la sarkig puepreela C Hide rocas that this monilas carnat daplay a l TAD Ii you are we problems palh the divica cick Troubleshoot bo Clair ted Check bos SA aba bebe ida modes hal aa Teen china pci comtecih Tha may lead to an tamara chopa and damagad Device uragas Lina iha dave estela Welcome to the Hardware
7. 0 14 Min 06 80 SAMSUNG 7267864 800 SAMSUNG 7267864 0032 0 2 201 24 18 0900 20 200 88 0 10 Min 815 56 480 0 801 801 881 80 8 200 128 0818 717 100 0800 SAMSUNG 7267864 902 10 11 30 0771 400 200 0800 7267864 0870 SAMSUNG 7267864 800 7267 800 7267 8 800 77777 8 800 080 1188 8 800 200 0400 8 800 502 0000 140 1234 1300 362 603 800 810 5858 010 6475 1880 3698 4698 http www samsung com dk http www samsung com fi http www samsung com fr http www samsung de http www samsung com hu http www samsung com it http www samsung lu http www samsung com nl http www samsung com no http www samsung com pl http www samsung com pt http www samsung com uk http www samsung com sk http www samsung com es http www samsung com se http www samsung com ch http www samsung com uk http www samsung ee http www samsung com lv http www samsung t http www samsung kz http www samsung ru http www samsung com ur http www samsung uz http www samsung com au http www samsung com cn http www samsung com hk INDIA 3030 8282 1800 1100 11 http www samsung convin INDONESIA 0800 112 8888 http www samsung com id JAPAN 0120 327 527 http www samsung com jp MALAYSIA 1800 88 9999 http www samsung com my PHILIPPINES 1800 10 SAMSUNG 7267864 http www samsung com ph SINGAPORE 1800 SAMSUNG 7267864 http www samsung com sg THAILAND 1800 29
8. 63 981 79 976 Horizontal Frequency Vertical Frequency Vertical Frequency Hz 66 667 74 551 75 062 70 086 59 940 70 087 75 000 72 809 56 250 60 317 72188 75 000 60 004 70 069 75 029 75 000 60 000 60 020 75 025 Pixel Clock MHz 30 240 57 284 100 000 25 175 25 175 28 322 31 500 31 500 36 000 40 000 50 000 49 500 65 000 75 000 78 750 108 000 108 000 108 000 135 000 Sync Polarity H V J J a Je J j The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency Unit kHz Like a fluorescent lamp the screen has to repeat the same image many times per second to display an image to the user The frequency of this repetition is called the Vertical Frequency or Refresh Rate Unit Hz SyncMaster 932BPlus 932B Model The color and appearance of the product may vary depending on the model and the product specifica tions are subject to change without prior notice for reasons of performance enhancement B Safety Precautions E Introduction Connections m Using the Software u Adjusting the Monitor Troubleshooting E Specifications E Information O Specifications specifications Powersaver Preset Timing Modes 3 Specifications General Model Name Syn
9. AF Erophot IN roporivoa a Gofur a Device Balootizn Color Conmolion Geron dapt Morbo Trabia Color hiana PA aie Pp LI Pha al Pio A L E nari int HM ore A Borren aah naka Gl Heats CO Hide dries Ue tds errors Coren cece Cisa ka tite Fen kua dra gu IN srir I apia mata Gee apr ceed Tihim an hued bo et adds cia Ara darme ts ir nae T Monitor driver installation is completed Microsoft Windows 2000 Operating System uk 8 When you can see Digital Signature Not Found on your monitor follow these steps Choose the OK button on the Insert disk window Click the Browse button on the File Needed window Choose A D Driver then click the Open button and then click the OK button How to install Click Start Setting and then Control Panel Double click the Display icon E Select the Settings tab and click the Advanced Properties button Choose Monitor Casel If the Properties button is inactive it means your monitor is properly configured Please stop installation Case2 If the Properties button is active click the Properties button then follow next steps continually O Click Driver and then click Update Driver then click the Next button Choose Display a list of the known drivers for this device so that can choose a specific driver then click Next and then click Have disk Click the Browse button then choose A D Driver Cl
10. Update Wizard Tinig kasa haka pau naal sota bor 040 2001 Plug and Ple Monos 51 2001 0 if pour hard come wiih an relation CD Tu wia oles Sana ee akbay fe To update thee ceiver for thie device What de you mani the wizaid lo do h ribal the kaban aiara Recommended ay AE I ie ikanta ale alar he dibres poll bambi bo penal gire Te well des here Sarai Hardware Update Wizard have a dak that Dorina the deves poo want lo maladi chek Maree D 2 Search ka the basi diva in hese locator eta relate an an la pata and tam able peda The belt dmo found Kal be malaked Sesch remowable mada Boppy DOM Include thes Icon in he peach E BIL mercy an E it youn Choose this option ko select the desce dire homa bet Windows does mot gusarias that the deer pou choca veal ba he beret match for pour hudas Click the Browse button then choose A D Driver and choose your monitor model in the model list and click the Next button Install From Disk Hardware Update Wizard Sold the dewee diwei you want lo malal Lor thin haide rebel the manulachutet s matallabon dk and then z i Pues ik Seino the kau are modal of youn kaaa derrito aed ee cite Kesi IN pau make sure thal the conect dive is selected below i EE has i dick alionana Ha hasi you mari bi ribal bek Hawa Dok Moda Samsung pas Copy manulactuser s hes hom y Thin driwer is ot digitally signed Have Cink Tal na he ya marina bi mala
11. and monitor settings In most cases the monitor installation will proceed automatically unless the user wishes to select alternate settings Dot Acceptable TFT LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm one millionth above are used for this product But the pixels of RED GREEN BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen This is not from bad quality and you can use it without any problelms For example the number of TFT LCD sub pixels contained in this product are 3 932 160 Design and specifications are subject to change without prior notice Class B Equipment Information Communication equipment for residential use This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas Class B equipment emits less electromagnetic waves than Class A equipment specifications Powersaver Preset Timing Modes O PowerSaver This monitor has a built in power management system called PowerSaver This system saves energy by switching your monitor to low power mode when it has not been used for a certain amount of time The monitor automatically returns to normal operation when you press a key on the keyboard For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods The PowerSaver system operates
12. eka le Coco If you can see following Message window then click the Continue Anyway button Then click the OK button Hardware Installation The software you ane installing for this hardware Samsung eam has nai Paced Window Logo being ko wendy d compabbdiy al fined OP Tell 1 e the bating ix gta Continuing yout installation of this awa mag impair or destabilize the conect operation of your system either immediately of m the future Microsoft strongly recommends thal gow stop hit installation now and contact the hardware vendor for software that haz passed Windows Logo testing 1 STOP Instalator This monitor driver is under certifying MS logo and this installation doesn t damage your system The certified driver will be posted on Samsung Monitor homepage http www samsung com Click the Close button then click the OK button continually Hardware Update Wizard aaa Gora Dia Completing the Hardware Update Wizard ia Samsung sao The wat kai feted ritaling the softener koi Diya Priis gt EE a Samsung kaka Drives Bata TU 1200 Diyes Yasay 1000 Digital Signs hol kal eigen Drvar Dota To vis details about the dira kilan To pasale iho derea dos iha Asus L Bol Back Driver tha daa bada after upang iho diyes roll back bo ina paro maabala chorea DE Raha ban the warned Ta umma the drem Advanced Co cme Plug and bary Monitor anal
13. high humidity and exposed to chemical substances and where it operates for 24 hours such as at airports train stations etc Failure to do so may cause serious damage to your monitor Place your monitor in a location with low humidity and a minimum of dust gt Failure to do so may cause electric shock or fire inside the monitor Do not drop the monitor when moving it This may cause damage to the product or the person carrying it Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf t Dropping the product may cause damage to the product or the person carrying it Do not place the product on the floor t Take care as someone specifically children may trip over it Do not place the product on an unstable or small surface area gt Place the product on an even and stable surface as the product may fall and cause harm to someone walking by specifically children To prevent the spread of fire keep candles or other open flames away from this product at all times Otherwise this may cause fire Keep any heating devices away from the power cable t A melted coating may cause electric shock or fire Do not install the product in places with poor ventilation for instance a bookshelf closet etc Any increase in the internal temperature may cause fire Put down the monitor carefully t Failing to do so may damage the monitor
14. image or blurriness may appear gt Change the mode to energy saving mode or set a screensaver to a changing picture when away from the monitor for an extended period of time Adjust the resolution and frequency to the level appropriate for the model gt An inappropriate resolution may cause undesirable picture quality 17 inch 43 cm 1280 x 1024 19 inch 48 cm 1280 x 1024 Viewing the monitor continuously at a too close angle may result in damage to your eyesight To ease eye strain take at least a five minute break after every hour of using the monitor Do not install the product on an unstable uneven surface or a location prone to vibrations E o Vs o O wt Cel gt Dropping the product may cause damage to the product or the person carrying it Using the product in a location prone to vibrations may shorten the lifetime of the product or may cause the product to catch fire When moving the monitor turn off and unplug the power cord Make sure that all cables including the antenna cable and cables connected to other devices are disconnected before moving the monitor gt Failure to disconnect cables may damage it and cause fire or electric shock Place the product out of children s reach as they could damage by hanging onto it gt A falling product may cause injury to the person or even fatality When not using the product for an extended period of time keep the
15. installation CD into the CD ROM drive Click the MagicTune installation file Select installation Language Click Next When the Installation Shield Wizard window appears click Next Select agree to the terms of the license agreement to accept the terms of use Choose a folder to install the MagicTune program Click Install The Installation Status window appears SoS eS 9 Click Finish 10 When the installation is complete the MagicTune executable icon appears on your desktop Double click the icon to start the program Han MagicTune execution icon may not appear depending on specification miira of computer system or monitor ERC ERA RARA ERE ERRE FFAA FEF vio Installation Problems MagicTune The installation of MagicTune can be affected by such factors as the video card motherboard and the network environment vee O System Requirements OS e Windows 2000 e Windows XP Home Edition e Windows XP Professional e Windows Vista It is recommended using MagicTune in Windows 2000 il n lure igya or later Hardware e 32MB Memory above e 60MB Hard disk space above For more information visit the MagicTune website Uninstall The MagicTune program can be removed only by using the Add or Remove Programs option of the Windows Control Panel Perform the following steps remove MagicTune 1 Go to Task Tray Start Settings and select Contr
16. is not from bad quality and you can use it without uneasiness gt For example the number of TFT LCD sub pixels that is contained in this product are 3 932 160 When cleaning the monitor and the panel outside please apply the recommended small amount of cleaner by using a soft cloth to polish Do not force the LCD area but rub softly If excessive force is applied you can have a stain on it If you are not satisfied with the picture quality you can get better quality of picture by performing the auto adjustment function in display screen that is appeared as window termination button is pressed If there s still noise after the automatic adjustment use the FINE COARSE adjustment function When viewing a fixed screen for an extended period of time a residual image or blurriness may appear Change the mode to energy save or set a screensaver to move the picture when you need to be away from the monitor for an extended period of time Contact SAMSUNG WORLDWIDE Terms For Better Display Authority 3 Authority G Information in this document is subject to change without notice 2007 Samsung Electronics Co Ltd All rights reserved Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co Ltd is strictly forbidden Samsung Electronics Co Ltd shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use o
17. lt P SyncMaster 732NPlus 932BPlus 732N 932B it Prepall a pr ao Introduction Connections Software wo Using the A O OS dadas The color and appearance of the product may vary depending on the model and the product specifica tions are subject to change without prior notice for reasons of performance enhancement u Safety Precautions E Introduction Connections m Using the Software e Adjusting the Monitor Troubleshooting Specifications Information O Safety Precautions Notation Power Installation Cleaning and Use Others 3 Notation Please read the following safety instructions as they are designed to prevent damage to property and harm to the user ce Warning Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment ER Notational Conventions SN Prohibited D t di bl a Q o not disassemble E Q Do not touch 5 Ground to prevent an electric shock Q Important to read and understand at all times Disconnect the plug from the outlet Notation Power Installation Cleaning and Use Others 3 Power When not used for extended period of time set your computer to DPMS If using a screen saver set it to active screen mode The images here are for reference only and are not applicable in all cases or countries Shortcut to Anti Afterimage Instructions Do not us
18. with a VESA DPMS compliant video card installed in your computer Use the software utility installed on your computer to set up this feature Power off State Normal Operation Power saving mode EPA ENERGY 2000 Power Indicator Blue Blue Blinking Off Power Consumption Less than 34 W Less than 1 W Less than 1 W This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality As an ENERGY STAR Partner SAMSUNG has determined that this ENERGY STAR product meets the ENERGY STAR guidelines for energy efficiency 3 Preset Timing Modes specifications PowerSaver Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes the screen will be adjusted automatically However if the signal differs the screen may go blank while the power LED is on Refer to the video card manual and adjust the screen as follows Display Mode MAC 640 x 480 MAC 832 x 624 MAC 1152 x 870 IBM 640 x 350 IBM 640 x 480 IBM 720 x 400 VESA 640 x 480 VESA 640 x 480 VESA 800 x 600 VESA 800 x 600 VESA 800 x 600 VESA 800 x 600 VESA 1024 x 768 VESA 1024 x 768 VESA 1024 x 768 VESA 1152 x 864 VESA 1280 x 960 VESA 1280 x 1024 VESA 1280 x 1024 Horizontal Frequency KHz 35 000 49 726 68 681 31 469 31 469 31 469 37 500 37 861 35 156 37 879 48 077 46 875 48 363 56 476 60 023 67 500 60 000
19. 3232 02 689 3232 http www samsung com th TAIWAN 0800 329 999 http www samsung com tw VIETNAM 1 800 588 889 http www samsung com vn Middle East amp Africa SOUTH AFRICA 0860 7267864 SAMSUNG http www samsung com za 800SAMSUNG 7267864 U A E 8000 4726 http www samsung com mea Contact SAMSUNG WORLDWIDE Terms For Better Display Authority 3 Terms O Dot Pitch The image on a monitor is composed of red green and blue dots The closer the dots the higher the resolution The distance between two dots of the same color is called the Dot Pitch Unit mm Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user The frequency of this repetition per second is called the Vertical Frequency or Refresh Rate Unit Hz Example If the same light repeats itself 60 times per second this is regarded as 60 Hz Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle The inverse number of the Horizontal Cycle is called Horizontal Frequency Unit kHz G Interlace and Non Interlace Methods Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non Interlace method while showing odd lines and then even lines in turn is called the Interlace method The Non Interlace method is used for the majority of monitors to ens
20. 7864 http www samsung com mx Latin America ARGENTINE 0800 333 3733 http www samsung com ar BRAZIL 4004 0000 http www samsung com br CHILE 800 726 7864 SAMSUNG http www samsung com cl COLOMBIA 01 8000112112 http www samsung com co COSTA RICA 0 800 507 7267 http www samsung com latin ECUADOR 1 800 10 7267 http www samsung com latin EL SALVADOR 800 6225 http www samsung com latin GUATEMALA 1 800 299 0013 http www samsung com latin JAMAICA 1 800 234 7267 http www samsung com latin PANAMA 800 7267 http www samsung com latin PUERTO RICO 1 800 682 3180 http www samsung com latin REP DOMINICA 1 800 751 2676 http www samsung com latin TRINIDAD 4 TOBAGO 1 800 7267 864 http www samsung com latin VENEZUELA 0 800 100 5303 http www samsung com latin Europe BELGIUM CZECH REPUBLIC DENMARK FINLAND FRANCE GERMANY HUNGARY ITALIA LUXEMBURG NETHERLANDS NORWAY POLAND PORTUGAL REPUBLIC OF IRELAND SLOVAKIA SPAIN SWEDEN SWITZERLAND U K CIS ESTONIA LATVIA LITHUANIA KAZAKHSTAN RUSSIA UKRAINE UZBEKISTAN Asia Pacific AUSTRALIA CHINA HONG KONG 02 201 2418 844 000 844 Distributor pro eskou republiku http www samsung com be http www samsung com cz Samsung Zit Ceska organiza ni slo ka yskocilova 4 14000 Praha 4 7070 19 70 030 6227 515 3260 SAMSUNG 7267864 0 15 min 01805 121213
21. Europe only Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal PRODUCT INFORMATION Image Retention Free LCD Monitors and TVs may have an image retention when switching from one image to another especially after displaying a stationary image for a long time This guide is to demonstrate a correct usage of LCD products in order to protect them from Image retention Warranty Q Warranty does not cover any damage caused by image retention Burn in is not covered by the warranty What is Image retention During normal operation of a LCD panel pixel image retention doesn t occur However if the same image is displayed for a l
22. P Set the resolution in the Control Panel gt Appearance and Themes gt Display gt Screen Saver Set the function in the BIOS SETUP of the computer Windows ME 2000 Set the resolution in the Control Panel Display Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Manual How can clean the outer case LCD Panel Disconnect the power cord and then clean the monitor with a soft cloth using either a cleaning solution or plain water Do not leave any detergent or scratches on the case Do not let any water enter the monitor Check List Q amp A Self Test 3 Self Test Self Test Feature Check Warning Messages Environment Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly Self Test Feature Check zia Tum off both your computer and the monitor Unplug the video cable from the back of the computer E Tum on the monitor If the monitor is functioning properly you will see a box in the illustration below Check Signal Cable This box appears during normal operation if the video cable becomes disconnected or damaged Tum off your monitor and reconnect the video cable then tum on both your computer and the monitor If your monitor screen remains blank after using the previous procedure check your video controller and computer system your monitor is functioning p
23. age may indicate that the monitor is out of scan range or that you need to check the signal cable Not Optimum Mode Recommended Mode 1280 x 1024 60Hz Environment sl The location and the position of the monitor may influence the quality and other features of the monitor If there are any sub woofer speakers near the monitor unplug and relocate the woofer to another room Remove all electronic devices such as radios fans clocks and telephones that are within 3 feet one meter of the monitor Useful Tips si A monitor recreates visual signals received from the computer Therefore if there is a problem with the computer or the video card this can cause the monitor to become blank have poor coloring become noisy and video mode not supported etc In this case first check the source of the problem and then contact the Service Center or your dealer Judging the monitor s working condition If there is no image on the screen or a Not Optimum Mode Recommended Mode 1280 x 1024 60 Hz message comes up disconnect the cable from the computer while the monitor is still powered on If there is a message coming up on the screen or if the screen goes white this means the monitor is in working condition In this case check the computer for trouble SyncMaster 732NPlus 732N Modi E The color and appearance of the product may vary depending on the model and the product specifica tions are subject t
24. c 20 Sec 200 Sec MENU gt poll gt a F gt gt dE gt MENU Play Stop OQ 99 99 ee Menu Description Play Stop Image parameters are replaced with the factory default values Image Reset Q Q MENU a T gt e gt gt MENU Color parameters are replaced with the factory default Color Reset values Q Q MENU a T gt la gt ll Sa gt MENU a Information i Menu Description Shows a video source display mode on the OSD screen Information MENU gt de SyncMaster 932BPlus 932B Model E The color and appearance of the product may vary depending on the model and the product specifica tions are subject to change without prior notice for reasons of performance enhancement B Safety Precautions E Introduction u Connections m Using the Software E Adjusting the Monitor E Troubleshooting E Specifications E Information O Adjusting the Monitor Control Buttons Direct Functions OSD Function 3 Control Buttons O 94 0 O MENU IL Opens the OSD menu Also use to exit the OSD menu or return to the previous menu W These buttons allow you to adjust items in the menu E Press this button to activate a highlighted menu item SOO AUTO When the AUTO button is pressed the Auto Adjustment screen appears as shown in the animated screen on the center Control Buttons Direct Functions OSD Function 3 Direct Functions G AUTO Menu Descripti
25. cMaster 932BPlus SyncMaster 932B LCD Panel Size 19 Diagonal 48 cm Display area 376 32 mm H x 301 056 mm V Pixel Pitch 0 294 mm H x 0 294 mm V Synchronization Horizontal 30 81 kHz Vertical 56 75 Hz Display Color 8 bit color 16 2M Resolution Optimum resolution 1280 x 1024 60 Hz Maximum resolution 1280 x 1024 75 Hz Input Signal Terminated RGB Analog DVI Digital Visual Interface Compliant Digital RGB 0 7 Vp p 5 TTL level V high 2 2 0V V low lt 0 8V Maximum Pixel Clock 135 MHz Analog Digital Power Supply AC 100 240 V 10 96 50 60 Hz Signal Cable 15pin to 15pin D sub cable Detachable DVI D to DVI D connector Detachable Option Dimensions W x H x D Weight 418 0 x 418 0 x 199 0 mm 16 4 x 16 4 x 7 8 inch 4 0 kg 8 8 Ibs Environmental considerations Operating Temperature 50 F 104 F 10 C 40 C Humidity 10 80 non condensing Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 95 non condensing Plug and Play Capability This monitor can be installed on any Plug amp Play compatible system The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings In most cases the monitor installation will proceed automatically unless the user wishes to select alternate settings Dot Acceptable TFT LCD panels manufactured by using advanced semiconductor technology wit
26. ce please call the phone number on the Information section or contact your dealer Symptom No images on the screen cannot turn on the monitor Check List Is the power cord connected properly Can you see Check Signal Cable on the screen If the power is on reboot the computer to see the initial screen the login screen which can be seen Can you see Not Optimum Mode Recommended Mode 1280 x 1024 60 Hz on the screen There is no image on the screen Is the power indicator on the monitor blinking at 1 second intervals Solutions Check the power cord connection and supply Connected using the D sub cable Check the signal cable connection If the initial screen the login screen appears boot the computer in the applicable mode the safe mode for Windows ME XP 2000 and then change the frequency of the video card Refer to the Preset Timing Modes If the initial screen the login screen does not appear contact the Service Center or your dealer You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly Adjust the maximum resolution and frequency that the monitor can handle properly If the display exceeds SXGA or 75 Hz a Not Optimum Mode Recommended Mode 1280 x 1024 60 Hz message is displayed If the display exceeds 85 Hz the display will work properly but the Not Optimum Mode R
27. combination of characters and background color with large difference in luminance Avoid using Grey colors which can cause Image retention easily Avoid Colors with big difference in luminance Black amp White Grey Ex SYSTEM 245 Recommended settings Bright colors with little difference in luminance Change the characters color and background color every 30 minutes Ex SYSTEM 245 SYSTEM 245 STATUS OK STATUS OK Every 30 minutes change the characters with movement AA UUZE he PUYAT KA1710 12 00 KA1710 12 00 UA0110 13 30 PALIT E LIAN11N 12 20 AA0002 14 00 FA7777 14 15 DJ The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it Image retention may not occur when a LCD panel is operated under normal conditions Normal conditions are defined as continuously changing video patterns When the LCD panel is operated for a long time with a fixed pattern over 12 hours there may be slight difference in voltage between electrodes that work the liquid crystal LC ina pixel The voltage difference between electrodes increases with time forcing the liquid crystal to lean When this occurs the previous image may be seen when the pattern is changed To prevent this the accumulated voltage difference must be decreased Common Electrode ITO Black Matrix Color Filter Gate Pixel Electrode Storage Capacito
28. computer If you installed a new video card or if you assembled the PC check if the installed the adapter video driver and the monitor driver Check if the scanning ratio of the video screen is set to between 56 Hz 75 Hz Do not exceed 75 Hz when using the maximum resolution If you have problems in installing the adapter video driver boot the computer in Safe Mode remove the Display Adapter at the Control Panel System Device Administrator and then reboot the computer to reinstall the adapter video driver X f problems repeatedly occur contact an authorized service center B Q amp A Question How can change the frequency How can adjust the resolution Check List Q amp A Self Test Answer The frequency can be changed by reconfiguring the video card Note that video card support can vary depending on the version of the driver used Refer to the computer or the video card manual for details Windows XP Set the resolution in the Control Panel gt Appearance and Themes Display Settings Windows ME 2000 Set the resolution in the Control Panel Display Settings Contact the video card manufacturer for details How can set the Power Saving function Windows XP Set the resolution in the Control Panel gt Appearance and Themes Display Screen Saver Set the function in the BIOS SETUP of the computer Windows ME 2000 Set the resolution in
29. d Did you install the program Install the monitor driver according to the Driver Installation Instructions To check whether your PC is available for MagicTune feature follow the steps below When Windows is XP Control Panel Performance and Maintenance System gt Hardware Device Manager gt Monitors gt After deleting Plug and Play monitor find Plug and Play monitor by searching new Hardware MagicTune is an additional software for the monitor Some graphic cards may not support your monitor When you have a problem with the graphic card visit our website to check the compatible graphic card list provided http www samsung com monitor magictune Download the latest program The program can be downloaded http www samsung com monitor magictune Reboot the computer after installing the program for the first time If a copy of the program is already installed remove it reboot the computer and then install the program again You need to reboot the computer for it to operate normally after installing or removing the program Visit the MagicTune website and download the installation software for MagicTune MAC D Check the following items if there is trouble with the monitor Check if the power cord and the video cables are properly connected to the computer Check if the computer beeps more than 3 times when booting If it does ask the service center to check the main board of the
30. de for a certain time period You can set the amount of time the menu will wait before it is turned off 5 Sec 10 Sec 20 Sec 200 Sec MENU gt poll gt a F gt gt dE gt MENU Play Stop OQ 99 99 ee Menu Auto Source Image Reset Color Reset E Information zi Description Select Auto Source for the monitor to automatically select the signal source MENU gt gt H gt gt gt MENU Image parameters are replaced with the factory default values MENU gt gt H gt a F gt H gt gt MENU Color parameters are replaced with the factory default values MENU sa gt H gt a gt H gt dy gt MENU Play Stop 909 29 99 Menu Description Shows a video source display mode on the OSD screen Information MENU gt di SyncMaster 732NPlus 732N Model The color and appearance of the product may vary depending on the model and the product specifica tions are subject to change without prior notice for reasons of performance enhancement B Safety Precautions B Adjusting the Monitor O Troubleshooting 3 Check List A Introduction E Troubleshooting Connections E Using the Software u Specifications E Information Check List Q amp A Self Test Before calling for assistance check the information in this section to see if you can remedy any problems yourself If you do need assistan
31. e Blinking Off Power Consumption Less than 38 W Less than 1 W Less than 1 W This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality As an ENERGY STAR Partner SAMSUNG has determined that this product meets the ENERGY STAR guidelines for energy efficiency IS Preset Timing Modes ENERGY STAR specifications PowerSaver Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes the screen will be adjusted automatically However if the signal differs the screen may go blank while the power LED is on Refer to the video card manual and adjust the screen as follows Display Mode MAC 640 x 480 MAC 832 x 624 MAC 1152 x 870 IBM 640 x 350 IBM 640 x 480 IBM 720 x 400 VESA 640 x 480 VESA 640 x 480 VESA 800 x 600 VESA 800 x 600 VESA 800 x 600 VESA 800 x 600 VESA 1024 x 768 VESA 1024 x 768 VESA 1024 x 768 VESA 1152 x 864 VESA 1280 x 960 VESA 1280 x 1024 VESA 1280 x 1024 Horizontal Frequency KHz 35 000 49 726 68 681 31 469 31 469 31 469 37 500 37 861 35 156 37 879 48 077 46 875 48 363 56 476 60 023 67 500 60 000 63 981 79 976 Horizontal Frequency Vertical Frequency Hz 66 667 74 551 75 062 70 086 59 940 70 087 75 000 72 809 56 250 60 317 72 188 75 000 60 004 70 069 75 029 75 000 60 000 60 020 75 025 Pixel Cloc
32. e a damaged or loose plug This may cause electric shock or fire Do not pull the plug out by the wire nor touch the plug with wet hands This may cause electric shock or fire Use only a properly grounded plug and receptacle An improper ground may cause electric shock or equipment damage Class Equipment only Insert the power plug firmly so that it does not come loose gt A bad connection may cause fire Do not bend the plug excessively and wire nor place heavy objects upon them which could cause damage This may cause electric shock or fire Do not connect too many extension cords or plugs to one outlet This may cause fire Do not disconnect the power cord while using the monitor gt A surge may be caused by the separation and may damage the monitor Do not use the power cord when the connector or plug is dusty gt If the connector or plug of the power cord is dusty clean it with a dry cloth gt Using the power cord with a dusty plug or connector may cause an electric shock or fire To disconnect the apparatus from the mains the plug must be pulled out from the mains socket therefore the mains plug shall be readily operable Installation This may cause electric shock or fire Notation Power Installation Cleaning and Use Others Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust high or low temperatures
33. e electric shock or fire Unplug the power cord from the power outlet and wipe the product using a soft dry cloth Do not use any chemicals such as wax benzene alcohol thinners insecticide air freshener lubricant or detergent Contact the SAMSUNG customer care center or Customer Center for interior Wi cleaning once a year gt Keep the product s interior clean Dust which has accumulated in the interior over an extended period of time may cause a malfunction or fire Notation Power Installation Cleaning and Use Others 3 Others Do not remove the cover or back This may cause electric shock or fire Refer to a qualified servicing company If your monitor does not operate normally in particular if there is any unusual sound or smell coming from the monitor unplug it immediately and the Service Center This may cause electric shock or fire Keep the product away from places exposed to oil smoke or moisture do not install inside a vehicle This may cause a malfunction electric shock or fire In particular avoid operating the monitor near water or outdoors where it could be exposed to snow or rain If the monitor is dropped or the casing is damaged turn the monitor off and unplug the power cord Then contact the Service Center The monitor may malfunction causing electric shock or fire Disconnect the plug from the outlet during storms or lightning or if it is not us
34. ecommended Mode 1280 x 1024 60 Hz message appears for one minute and then disappears Please change to the recommended mode during this one minute period The message is displayed again if the system is rebooted The monitor is in PowerSaver mode Press a key on the keyboard to activate the monitor and restore the image on the screen If there is still no image press the button Then press any key on the keyboard again to activate the monitor and restore the image on the screen cannot see the On Screen Display The screen shows strange colors or just black and white The screen suddenly has become unbalanced The screen is out of focus or OSD cannot be adjusted LED is blinking but no images on the screen There are only 16 colors shown on the screen The screen colors have changed after changing the video card There is a message that reads Unrecognized monitor Plug amp Play VESA DDC monitor found Check when MagicTune does not function properly Have you locked the On Screen Display OSD Menu to prevent changes Is the screen displaying only one color as if looking at the screen through a cellophane paper Have the screen colors become strange after running a program or due to a crash between applications Has the video card been set properly Have you changed the video card or the driver Have you adjusted the resolution or frequency to the
35. ed for a long period of time gt Failure to do so may cause electric shock or fire Do not try to move the monitor by pulling only the wire or the signal cable This may cause a breakdown electric shock or fire due to damage to the cable Do not move the monitor right or left by pulling only the wire or the signal cable This may cause a breakdown electric shock or fire due to damage to the cable Do not cover the vents on the monitor cabinet gt Bad ventilation may cause a breakdown or fire Do not place water containers chemical products or small metal objects on the monitor A nga This may cause a malfunction electric shock or fire tg Di If a foreign substance enters the monitor unplug the power cord and contact the a Service Center o dad pw Keep the product away from combustible chemical sprays or inflammable substances This may cause an explosion or fire Never insert anything metallic into the monitor openings This may cause electric shock fire or injury Do not insert metal objects such as chopsticks wire and tools or inflammable objects such as paper or matches into the vent headphone port or AV ports or etc gt This may cause electric shock or fire If an alien substances or water enters the product turn the product off unplug the power connector from the wall outlet and contact the Service Center When viewing a fixed screen for an extended period of time residual
36. eo card Connect the signal cable to the 15 pin D sub port on the back of your monitor RGB IN iza Connected to a Macintosh Connect the monitor to the Macintosh comp uter using the D sub connection cable Turn on your computer and monitor If your monitor displays an image installation is completed Connecting Cables Using the Stand 3 Using the Stand Folding the base You can tilt the monitor upwards at an angle of 0 to18 SyncMaster 932BPlus 932B Model The color and appearance of the product may vary depending on the model and the product specifica tions are subject to change without prior notice for reasons of performance enhancement B Safety Precautions E Introduction Connections m Using the Software E Adjusting the Monitor 2 Troubleshooting E Specifications E Information O Connections Connecting Cables Using the Stand 3 Connecting Cables Rear of Monitor 9 Rear of Computer Macintosh SAMSUNG Connect the power cord for your monitor to the power port on the back of the monitor Plug the power cord for the monitor into a nearby outlet E Use a connection appropriate to the computer you are using Using the D sub Analog connector on the video card Connect the signal cable to the 15 pin D sub port on the back of your monitor RGB IN YA Using the DVI Digital connector on the video card Connect the DVI Cable to the DVI IN port on
37. ext Internet Game Sport Movie and Dynamic Contrast Brightness Menu Description Brightness When OSD is not on the screen push the button to adjust brightness 3 OSD Function Control Buttons Direct Functions OSD Function MM Picture Brightness Contrast ES Color MagicColor Color Tone Color Control Gamma BI Image Coarse Fine Sharpness H Position V Position J OSD Language H Position V Position Transparency Display Time E Setup Image Reset Color Reset EN Information W Picture Not available in MagicBright mode of Dynamic Contrast aih Menu Description Play Stop You can use the on screen menus to change the brightness according to personal preference Direct Access Feature When OSD is not on the screen EHOHHIESE push the button to adjust brightness Q Q Click here to see an animation clip MENU gt gt gt a MENU You can use the on screen menus to change the contrast according to personal preference Contrast Not available in MagicColor mode of Full and Intelligent Q Q MENU gt gt 4 7 gt H gt T5 MENU O ES Color Not available in MagicBright mode of Dynamic Contrast aiis Menu MagicColor Color Tone Color Control Gamma E Image la Description MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality O Off Returns to the or
38. f this material Samsung is the registered trademark of Samsung Electronics Co Ltd Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation VESA DPMS and DDC are registered trademarks of Video Electronics Standard Association the ENERGY STAR name and logo are registered trademarks of the U S Environmental Protection Agency EPA As an ENERGY STAR Partner Samsung Electronics Co Ltd has determined that this product meets the ENERGY STAR guidelines for energy efficiency All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners MEXICO IMPORTADO POR SAMSUNG ELECTRONICS MEXICO S A de C V Via Lopez Portillo No 6 Col San Fco Chilpan Tultitlan Estado de Mexico C P 54940 Tel 01 55 5747 5100 01 800 726 7864 EXPORTADO POR Samsung Electronics CO LTD 416 Mae tan 3dong Yeongtong gu Suwon City Gyeonggi do Korea
39. h precision of 1ppm one millionth above are used for this product But the pixels of RED GREEN BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen This is not from bad quality and you can use it without any problelms For example the number of TFT LCD sub pixels contained in this product are 3 932 160 Design and specifications are subject to change without prior notice D Class B Equipment Information Communication equipment for residential use This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas Class B equipment emits less electromagnetic waves than Class A equipment specifications PowerSaver Preset Timing Modes D PowerSaver This monitor has a built in power management system called PowerSaver This system saves energy by switching your monitor to low power mode when it has not been used for a certain amount of time The monitor automatically returns to normal operation when you press a key on the keyboard For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer Use the software utility installed on your computer to set up this feature Power off State Normal Operation Power saving mode EPA ENERGY 2000 Power Indicator Blue Blu
40. he screen colors have changed after changing the video card There is a message that indicator on the monitor blinking at 1 second intervals Connected using the DVI cable Have you locked the On Screen Display OSD Menu to prevent changes Is the screen displaying only one color as if looking at the screen through a cellophane paper Have the screen colors become strange after running a program or due to a crash between applications Has the video card been set properly Have you changed the video card or the driver Have you adjusted the resolution or frequency to the monitor restore the image on the screen If there is still no image press the SOURCE button Then press any key on the keyboard again to activate the monitor and restore the image on the screen You may get a blank screen if you boot the system before you connect the DVI cable or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals Connect the DVI cable and then reboot the system Unlock the OSD by pressing the MENU 11 button for at least 5 seconds Check the signal cable connection Make sure the video card is fully inserted in it s slot Reboot the computer Set the video card by referring to the video card manual Adjust screen image position and size using the OSD Adjust the resolution and frequency at the video card
41. hoose your monitor model in the model list then click the OK button O SAMSUNG monitor metales Select the display edapier on which you wart to intall he monitos Sala the miro aich you wai bo inatali If you can see following message window then click the Continue Anyway button Then click the OK button Microsoft Windows XP 2000 Operating System The software pou are installing for this hardware Samsung nl has not passed Windows Logo testing to werily its compatbdiy wath Windows XP Tel ma why thes basting is imputari Continuing your installation of this software may impair or destabilize the comect operation of your system either i of in the future Microsoft strongly recommends that pou stop this installation now and contact the hardware vendor for software that haz passed Windows Logo testing This monitor driver is under certifying MS logo and this installation doesn t damage your system The certified driver will be posted on Samsung Monitor homepage http www samsung com Monitor driver installation is completed O Installing the Monitor Driver Manual Windows Vista Windows XP Windows 2000 Windows ME Windows NT Linux Microsoft Windows Vista Operating System ii Insert your Manual CD into your CD ROM drive Click 4 Start and Control Panel Then double click on Ap pearance and Personalization apor ide Wal Weal ia ama ee Poe Po meee Phl
42. ick the Open button then click the OK button Choose your monitor model and click the Next button then click Next button D Click the Finish button then the Close button If you can see the Digital Signature Not Found window then click the Yes button And click the Finish button then the Close button Microsoft Windows Millennium Operating System i Click Start Setting and then Control Panel Double click the Display icon Select the Settings tab and click the Advanced Properties button Select the Monitor tab Click the Change button in the Monitor Type area Choose Specify the location of the driver Choose Display a list of all the driver in a specific location then click the Next button Click the Have Disk button Specify A D driver then click the OK button T Select Show all devices and choose the monitor that corresponds to the one you connected to your computer and click OK D Continue choosing Close button and OK button until you close the Display Properties dialogue box Microsoft Windows NT Operating System tl O Click Start Settings Control Panel and then double click Display icon In the Display Registration Information window click the Settings tab and then click All Display Modes Select a mode that you wish to use Resolution Number of colors and Vertical frequency and then click OK
43. ie and Dynamic Contrast Brightness Menu Description Brightness When OSD is not on the screen push the button to adjust brightness BD SOURCE Menu Description SOURCE Selects the Video signal while the OSD is off Analog Digital ID OSD Function Picture Brightness ES Color MagicColor 5 Image Coarse HH OSD Language E Setup Auto Source O Information Contrast Color Tone Fine H Position Image Reset Control Buttons Direct Functions OSD Function Color Control Gamma Sharpness H Position V Position V Position Transparency Display Time Color Reset O E Picture Not available in MagicBright mode of Dynamic Contrast si Menu Description Play Stop You can use the on screen menus to change the brightness according to personal preference Direct Access Feature When OSD is not on the screen Q Q EHUNMESS push the button to adjust brightness F Click here to see an animation clip MENU gt gt gt gt MENU You can use the on screen menus to change the contrast according to personal preference Not available in MagicColor mode of Full and Intelligent Q Q Contrast MENU gt gt 4 7 gt H gt T5 MENU ES Color Not available in MagicBright mode of Dynamic Contrast uk Menu MagicColor Color Tone Color Control Gamma E Image la Description MagicColor is a new technology that Samsung has exclusively developed to imp
44. ie and Dynamic Contrast Each mode has its own pre configured brightness value You can easily select one of seven settings by simply pressing MagicBright control button Brightness button Adjust buttons W44 Enter button E AUTO button Power button 6 Power indicator 1 Custom Although the values are carefully chosen by our engineers the pre configured values may not be comfortable to your eyes depending on your taste If this is the case adjust the brightness and contrast by using the OSD menu 2 Text For documentations or works involving heavy text 3 Internet For working with a mixture of images such as texts and graphics 4 Game For watching motion pictures such as a game 5 Sport For watching motion pictures such as a sport 6 Movie For watching motion pictures such as a DVD or Video CD 7 Dynamic Contrast Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to create optimum contrast gt gt Click here to see an animation clip When OSD is not on the screen push the button to adjust brightness gt gt Click here to see an animation clip Adjust items in the menu Activates a highlighted menu item Use this button for auto adjustment gt gt Click here to see an animation clip Use this button for turning the monitor on and off This light glows blue during normal operation and blinks blue once as the monitor saves your adj
45. iginal mode Demo The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left Full Displays not only vivid natural color but also more realistic natural skin color with clearness Intelligent Displays vivid natural color with clearness MENU gt gt H gt gt gt MENU The tone of the color can be changed and one of four modes can be selected Cool Normal Warm and Custom Not available in MagicColor mode of Full and Intelligent MENU a gt H gt a Ko H gt MENU Adjusts individual Red Green Blue color balance Red Green Blue Not available in MagicColor mode of Full and Intelligent MENU gt Koala T gt H gt Y gt MENU Gamma correction changes the luminance of the colors with intermediate luminance Mode 1 Mode 2 Mode 3 MENU gt gt H gt a F gt H gt gt MENU Play Stop 909 ee 99 99 Menu Coarse Fine Sharpness H Position V Position CH OSD uk Description Removes noise such as vertical stripes Coarse adjustment may move the screen image area You may relocate it to the center using the horizontal control menu MENU sa F gt H gt H a gt MENU Removes noise such as horizontal stripes If the noise persists even after fine tuning repeat it after adjusting the frequency clock speed MENU gt am
46. k MHz 30 240 57 284 100 000 25 175 25 175 28 322 31 500 31 500 36 000 40 000 50 000 49 500 65 000 75 000 78 750 108 000 108 000 108 000 135 000 Sync Polarity H V of ya J The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency Unit kHz Vertical Frequency Like a fluorescent lamp the screen has to repeat the same image many times per second to display an image to the user The frequency of this repetition is called the Vertical Frequency or Refresh Rate Unit Hz The color and appearance of the product may vary depending on the model and the product specifica tions are subject to change without prior notice for reasons of performance enhancement B Safety Precautions Adjusting the Monitor u Connections E Specifications E Introduction u Using the Software Troubleshooting E Information O Information Contact SAMSUNG WORLDWIDE Terms For Better Display Authority 3 Contact SAMSUNG WORLDWIDE f you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center North America U S A 1 800 SAMSUNG 7267864 http Awww samsung com CANADA 1 800 SAMSUNG 7267864 http www samsung com ca MEXICO 01 800 SAMSUNG 726
47. monitor Unlock the OSD by pressing the MENU MI button for at least 5 seconds Check the signal cable connection Make sure the video card is fully inserted in it s slot Reboot the computer Set the video card by referring to the video card manual Adjust screen image position and size using the OSD Adjust the resolution and frequency at the video card Refer to the Preset Timing Modes The screen can be unbalanced due to the cycle of the video card signals Readjust Position by referring to the OSD Have you adjusted the resolution or frequency on the monitor Is the frequency properly adjusted when checking the Display Timing on the menu Have the Windows colors been set properly Has the video card been set properly Have you installed the monitor driver See the video card manual to see if the Plug amp Play VESA DDC function can be supported Magic Tune TM feature is found only on PC VGA with Window OS that supports Plug and Play Adjust the resolution and frequency of the video card Refer to the Preset Timing Modes Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes The maximum frequency per resolution may differ from product to product Windows XP Set the resolution in the Control Panel Appearance and Themes Display Settings Windows ME 2000 Set the resolution in the Control Panel Display Set
48. o pao mm poo rs lumigaya ed iri d pae a E Ce ee oie bers ee AS aa Wa aa mm de mban ua ee ee eee Wa ma ee oe ee ee ee ee eee ee Le Pe al ca a E cs e E SE E sk as A fe pimpe ee ee ee A pE E ing a a Tg Mp e e e al aga ka aa nj m KH Bigg A ba la eee eee Ser re oe EIAI iep HAN pang bia quel 5 ka Bay oe toros O Click Properties in the Monitor tab If the Properties button is deactivated it means the configuration for your monitor is completed The monitor can be used as is If the message Windows needs is displayed as shown in the figure below click Continue f Ment Tee i pie mede Than Ped eri CAD LA sen caret cy cacy aay ied o a Aspar andi damaged hard hee Account Control helps sop unauthorined changes to your compuler This monitor driver is under certifying MS logo and this installation doesn t damage your system The certified driver will be posted on Samsung Monitor homepage http www samsung com Click pa Driver in the Driver tab 0 6000 ENE maraot radicar Ta wawa Cet ele eco a orar lea To updale Ea giam poes dor A daraga Hahayaan mba mi Bi Pa a Check the Browse my computer for driver software checkbox and click Let me pick from a list of device drivers on my COMPUT Here 00 aU A each dos cher LOPD DET earth automatically dos upiabed driver oyhan iraan all pe ka pa pa el iha e
49. o change without prior notice for reasons of performance enhancement B Safety Precautions E Introduction Connections m Using the Software u Adjusting the Monitor Troubleshooting E Specifications E Information O Specifications specifications Powersaver Preset Timing Modes 3 Specifications General Model Name SyncMaster 732NPlus SyncMaster 732N LCD Panel Size 17 Diagonal 43 cm Display area 337 92 mm H x 270 336 mm V Pixel Pitch 0 264 mm H x 0 264 mm V Synchronization Horizontal 30 81 kHz Vertical 56 75 Hz Display Color 8 bit color 16 2M Resolution Optimum resolution 1280 x 1024 60 Hz Maximum resolution 1280 x 1024 75 Hz Input Signal Terminated RGB Analog 0 7 Vp p 5 TTL level V high 2 0V V low lt 0 8V Maximum Pixel Clock 135 MHz Analog Power Supply AC 100 240 V 10 96 50 60 Hz Signal Cable 15pin to 15pin D sub cable Detachable Dimensions W x H x D Weight 376 0 x 380 0 x 177 0 mm 14 8 x 14 9 x 6 9 inch 3 2 kg 7 0 lbs Environmental considerations Operating Temperature 50 F 104 F 10 C 40 C Humidity 10 80 non condensing Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 95 non condensing Plug and Play Capability This monitor can be installed on any Plug amp Play compatible system The interaction of the monitor and the computer systems will provide the best operating conditions
50. ol Panel in the menu If the program runs on Windows XP go to Control Panel in the Start menu 2 Click the Add or Remove Programs icon in Control Panel 3 In the Add or Remove Programs screen scroll down to find MagicTune Click on it to highlight it 4 Click the Change Remove button to remove the program 5 Click Yes to begin the uninstall process 6 Wait until the Uninstall Complete dialog box appears Visit the MagicTune website for technical support for MagicTune FAQs questions and answers and software upgrades SyncMaster 732NPlus 732N Model El The color and appearance of the product may vary depending on the model and the product specifica tions are subject to change without prior notice for reasons of performance enhancement B Safety Precautions E Introduction u Connections m Using the Software E Adjusting the Monitor E Troubleshooting E Specifications E Information O Adjusting the Monitor Control Buttons Direct Functions OSD Function 3 Control Buttons MENU IL Opens the OSD menu Also use to exit the OSD menu or return to the previous menu W These buttons allow you to adjust items in the menu E Press this button to activate a highlighted menu item SOO AUTO When the AUTO button is pressed the Auto Adjustment screen appears as shown in the animated screen on the center Control Buttons Direct Functions OSD Function O Direct Function
51. on When the AUTO button is pressed the Auto Adjustment screen appears as shown in the animated screen on the center Auto adjustment allows the monitor to self adjust to the incoming Analog signal The values of fine coarse and position are adjusted automatically Available in Analog mode only AUTO To make the automatic adjustment function sharper execute the AUTO function while the AUTO PATTERN is on t If auto adjustment does not work properly press AUTO button again to adjust picture with more accuracy t If you change resolution in the control panel auto function will be executed automatically OSD Lock amp Unlock AUTO button MENU button Menu OSD Lock amp Unlock Description This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings Lock Hold down the menu button for more than five seconds to activate the OSD adjustment lock function Unlock Hold down the menu button for more than five seconds to deactivate the OSD adjustment lock function Though the OSD adjustment lock function is activated you can still adjust the brightness and contrast and adjust MagicBright La using the Direct button O MagicBright Menu Description Push the MagicBright button to circle through available preconfigured MagicBright modes Seven different modes Custom Text Internet Game Sport Mov
52. ong time a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal This may cause the liquid crystal to build up in a certain areas of the display Thus the previous image is retained when switching to a new video image All display products including LCD are subject to image retention This is not a product defect Please follow the suggestions below to protect your LCD from image retention Power Off Screen Saver or Power Save Mode Ex Turn the power off when using a stationary pattern Turn the power off for 4 hours after 20 hours in use Turn the power off for 2 hours after 12 hours in use Usea Screen saver if possible Screen saver in one color or a moving image is recommended Set the Monitor to power off with the PC Display Properties Power Scheme Suggestions for specific applications Ex Airports Transit Stations Stock Markets Banks and Controlling Systems We recommend that you follow set up of your display system program as below Display Information together with Logo or Moving image cycle Ex Cycle Display Information for 1 hour followed by a Display Logo or moving image for 1 minute Change the Color Information periodically Use 2 different colors Ex Rotate the Color Information with 2 colors every 30 minutes Type 1 Type 1 FLGHT TIME 0Z348 20 30 FLGHT TIME gt Beye 20 30 UA102 21 10 lt UA102 21 10 Avoid using a
53. onitor Check if the power cord and the video cables are properly connected to the computer Check if the computer beeps more than 3 times when booting If it does ask the service center to check the main board of the computer Ifyou installed a new video card or if you assembled the PC check if the installed the adapter video driver and the monitor driver Check if the scanning ratio of the video screen is set to between 56 Hz 75 Hz Do not exceed 75 Hz when using the maximum resolution Ifyou have problems in installing the adapter video driver boot the computer in Safe Mode remove the Display Adapter at the Control Panel System Device Administrator and then reboot the computer to reinstall the adapter video driver f problems repeatedly occur contact an authorized service center Check List Q amp A Self Test O Q amp A Question Answer How can change the frequency The frequency can be changed by reconfiguring the video card Note that video card support can vary depending on the version of the driver used Refer to the computer or the video card manual for details How can adjust the resolution Windows XP Set the resolution in the Control Panel gt Appearance and Themes Display Settings Windows ME 2000 Set the resolution in the Control Panel Display Settings Contact the video card manufacturer for details How can set the Power Saving function Windows X
54. p gt H gt a F gt H gt 4 gt MENU Changes the clearance of image Not available in MagicColor mode of Full and Intelligent MENU gt F gt H gt a gt H gt MENU Changes the horizontal position of the monitor s entire display MENU gt F gt lH gt a F gt H gt F MENU Changes the vertical position of the monitor s entire display MENU gt poll gt a po H gt i F MENU Play Stop 99 99 Menu Language H Position V Position Transparency Display Time D Setup ik Description You can choose one of nine languages English Deutsch Espa ol Francais Italiano Svenska PyYCCKHA Portugu s T rk e The language chosen affects only the language of the OSD It has no effect on any software running on the computer MENU gt gt el gt e gt MENU You can change the horizontal position where the OSD menu appears on your monitor MENU gt amp gt H gt a F gt H gt a MENU You can change the vertical position where the OSD menu appears on your monitor MENU sa poll gt a F gt gt dE MENU Change the transparency of the background of the OSD MENU gt F gt llo a F gt la gt MENU The menu will be automatically turned off if no adjustments are made for a certain time period You can set the amount of time the menu will wait before it is turned off 5 Sec 10 Se
55. product unplugged gt Otherwise this may cause heat emission from the accumulated dirt or degraded insulation causing electric shock or fire Do not place your children s favorite toys or any other objects of interest on the product gt Children may try to climb on the product to retrieve an object The product could fall causing injury or even fatality When lifting up or moving the monitor do not lift the monitor upside down while holding only the stand This may cause your monitor to fall and become damaged or cause personal injury Good Postures When Using the Monitor Try to maintain a good posture when using the monitor e Keep your back straight e Keep a distance of about 45 50 cm between your eyes and the monitor screen Look at the screen from slightly above it and have the monitor directly in front of you e Tilt the monitor upwards by 10 20 degrees Adjust the monitor height so that the top of the monitor is slightly below eye level e Adjust the monitor angle so that there is no reflected light on the screen Try to maintain your arms perpendicular to your armpits e Keep your arms level with the back of your hands e Keep the angle of the elbow perpendicular e Keep the angle of the knees at more than 90 degree Do not let your feet fall up from the floor Adjust the arm position so that it is below the heart Correct Disposal of This Product Waste Electrical amp Electronic Equipment
56. r Cs Our LCD Monitor satisfies ISO13406 2 Pixel fault Class II SyncMaster 732NPlus 732N Model Po y The color and appearance of the product may vary depending on the model and the product specifica tions are subject to change without prior notice for reasons of performance enhancement u Safety Precautions E Introduction u Connections m Using the Software E Adjusting the Monitor Troubleshooting E Specifications E Information O Introduction Package Contents Your Monitor 3 Package Contents Please make sure the following items are included with your monitor If any items are missing contact your dealer Contact a local dealer to buy optional items Unpacking Monitor Manual ro Warranty Card User s Guide Monitor Driver Quick Setup Guide Not available in all Natural Color software locations MagicTune software Cable Power Cord D sub Cable D Others m ao ma ma Si i Tay SY Cleaning Cloth Will be applied to black and high gloss models only Package Contents Your Monitor 3 Your Monitor Front a O O MENU button M Open the OSD menu Also use to exit the OSD menu or return to the previous menu MagicBright button MagicBright is a new feature providing optimum viewing environment ata depending on the contents of the image you are watching Currently seven different modes are available Custom Text Internet Game Sport Mov
57. roperly G Warning Messages uli If there is something wrong with the input signal a message appears on the screen or the screen goes blank although the power indicator LED is still on The message may indicate that the monitor is out of scan range or that you need to check the signal cable Not Optimum Mode Recommended Mode 1280 x 1024 60Hz Environment zi The location and the position of the monitor may influence the quality and other features of the monitor gt If there are any sub woofer speakers near the monitor unplug and relocate the woofer to another room Remove all electronic devices such as radios fans clocks and telephones that are within 3 feet one meter of the monitor D Useful Tips zi A monitor recreates visual signals received from the computer Therefore if there is a problem with the computer or the video card this can cause the monitor to become blank have poor coloring become noisy and video mode not supported etc In this case first check the source of the problem and then contact the Service Center or your dealer Judging the monitor s working condition If there is no image on the screen or a Not Optimum Mode Recommended Mode 1280 x 1024 60 Hz message comes up disconnect the cable from the computer while the monitor is still powered on gt If there is a message coming up on the screen or if the screen goes white this means the monitor is in working condition In this ca
58. rove digital image and to display natural color more clearly without disturbing image quality O Off Returns to the original mode Demo The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left Full Displays not only vivid natural color but also more realistic natural skin color with clearness Intelligent Displays vivid natural color with clearness MENU gt gt H gt gt gt MENU The tone of the color can be changed and one of four modes can be selected Cool Normal Warm and Custom Not available in MagicColor mode of Full and Intelligent MENU a gt H gt a Ko H gt MENU Adjusts individual Red Green Blue color balance Red Green Blue Not available in MagicColor mode of Full and Intelligent MENU gt Koala T gt H gt Y gt MENU Gamma correction changes the luminance of the colors with intermediate luminance Mode 1 Mode 2 Mode 3 MENU gt gt H gt a F gt H gt gt MENU Play Stop 909 ee 99 99 Menu Coarse Fine Sharpness H Position V Position CH OSD uk Description Removes noise such as vertical stripes Coarse adjustment may move the screen image area You may relocate it to the center using the horizontal control menu MENU sa F gt H gt H a gt MENU Removes noise such as horizontal stripe
59. s G AUTO Menu Description When the AUTO button is pressed the Auto Adjustment screen appears as shown in the animated screen on the center Auto adjustment allows the monitor to self adjust to the incoming Analog signal The values of fine coarse and position are adjusted automatically Available in Analog mode only AUTO To make the automatic adjustment function sharper execute the AUTO function while the AUTO PATTERN is on t If auto adjustment does not work properly press AUTO button again to adjust picture with more accuracy t If you change resolution in the control panel auto function will be executed automatically OSD Lock amp Unlock AUTO button MENU button Menu OSD Lock amp Unlock Description This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings Lock Hold down the menu button for more than five seconds to activate the OSD adjustment lock function Unlock Hold down the menu button for more than five seconds to deactivate the OSD adjustment lock function Though the OSD adjustment lock function is activated you can still adjust the brightness and contrast and adjust MagicBright La using the Direct button O MagicBright Menu Description Push the MagicBright button to circle through available preconfigured MagicBright modes Seven different modes Custom T
60. s If the noise persists even after fine tuning repeat it after adjusting the frequency clock speed MENU gt amp gt H gt a F gt H gt 4 gt MENU Changes the clearance of image Not available in MagicColor mode of Full and Intelligent MENU gt F gt H gt a gt H gt MENU Changes the horizontal position of the monitor s entire display MENU gt F gt lH gt a F gt H gt F MENU Changes the vertical position of the monitor s entire display MENU gt poll gt a po H gt i F MENU Play Stop 99 99 Menu Language H Position V Position Transparency Display Time D Setup ik Description You can choose one of nine languages English Deutsch Espa ol Francais Italiano Svenska PyYCCKHA Portugu s T rk e The language chosen affects only the language of the OSD It has no effect on any software running on the computer MENU gt gt el gt e gt MENU You can change the horizontal position where the OSD menu appears on your monitor MENU gt amp gt H gt a F gt H gt a MENU You can change the vertical position where the OSD menu appears on your monitor MENU sa poll gt a F gt gt dE MENU Change the transparency of the background of the OSD MENU gt F gt llo a F gt la gt MENU The menu will be automatically turned off if no adjustments are ma
61. se check the computer for trouble SyncMaster 932BPlus 932B Model gt The color and appearance of the product may vary depending on the model and the product specifica tions are subject to change without prior notice for reasons of performance enhancement B Safety Precautions B Adjusting the Monitor O Troubleshooting 3 Check List A Introduction E Troubleshooting Connections E Using the Software u Specifications E Information Check List Q amp A Self Test Before calling for assistance check the information in this section to see if you can remedy any problems yourself If you do need assistance please call the phone number on the Information section or contact your dealer Symptom No images on the screen cannot turn on the monitor Check List Is the power cord connected properly Can you see Check Signal Cable on the screen If the power is on reboot the computer to see the initial screen the login screen which can be seen Can you see Not Optimum Mode Recommended Mode 1280 x 1024 60 Hz on the screen There is no image on the screen Is the power Solutions Check the power cord connection and supply Connected using the D sub cable Check the signal cable connection Connected using the DVI cable If you still see an error message on the screen when the monitor is connected properly check to see if the monitor status is set to analog
62. td Pe Br ird eo ooo Fat pew ree bet ore peck bem a lit of decos Scheer GA Muu Tes fet all Ch oreo deyr ufar mpa adt Ior dria r anal al dire wees r ibr peer ery ee re Click Have Disk and select the folder for example D Drive where the driver setup file is located and click OK Select the dived dr you wari Lo AKA fee tha Kaini be ecient es e iia Slate a Paa a Pe rie Pama Py erst il Pl ir Pe ee pets ir a chet Merve ie Hint Na Cara Pl karaan Select the model that matches your monitor from the list of monitor models on the screen and click Next Sohne the denne dina you ward o pial fee thea hardware A a e nr bred Sickel er Pare p deed Pres E aml Fria S ai a rra Pe dr paa ma NG rd e Hang Gaii played in sequence ET MWisdosa haa suo Addy ped year diet sols x abung oo Ta upime a ee ahea Ga Trem a e a acl haci la Pe preci Cit e pei dere T cara pa ee rad WA ds modes that he monitor cannot display Citira de check bene adora you lo pelect deplay modes that tha nog OR cono tarro desplay correctly The may lead bo n unusable E The my mupa EO Gaplay andor damaged hardware BI Extend the desktop onto the mortor Microsoft Windows XP Operating System ih Insert the CD into the CD ROM drive Click Start gt Control Panel then click the Appearance and Themes icon elit Pa Oe 0 8 Per Bue Te po sae i Erer Pe Dear a AS internet Caper gt
63. ter is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor the Natural Color S W is the very solution for this problem It is a color administration system developed by Samsung Electronics in association with Korea Electronics 4 Telecommunications Research Institute ETRI This is only available for Samsung monitors and ensures that the color of the images on the monitor are the same as the printed or scanned images For more information refer to Help F1 in the software program Installing the Natural Color Software Insert the CD included with the Samsung monitor into the CD ROM Drive The initial Natural Color screen will appear Click on Natural Color in the startup window to install the Natural Color software To install the program manually insert the CD included with the Samsung monitor into the CD ROM Drive click the Windows Start button select Run Enter D Color NCProSetup exe and then press the lt Enter gt key If the drive where the CD is inserted is not D enter the applicable drive Uninstalling the Natural Color Software Program Select Settings Control Panel from the Start menu and then double click Add Delete a program Select Natural Color from the list and then click the Add Delete button Monitor Driver Natural Color MagicTune 3 MagicTune Installation Insert the
64. the Control Panel Display Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Manual How can clean the outer case LCD Panel Disconnect the power cord and then clean the monitor with a soft cloth using either a cleaning solution or plain water Do not leave any detergent or scratches on the case Do not let any water enter the monitor Check List Q amp A Self Test 3 Self Test Self Test Feature Check Warning Messages Environment Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly O Self Test Feature Check ik Turn off both your computer and the monitor Unplug the video cable from the back of the computer Turn on the monitor If the monitor is functioning properly you will see a box in the illustration below Check Signal Cable This box appears during normal operation if the video cable becomes disconnected or damaged E Tum off your monitor and reconnect the video cable then turn on both your computer and the monitor If your monitor screen remains blank after using the previous procedure check your video controller and computer system your monitor is functioning properly O Warning Messages ul If there is something wrong with the input signal a message appears on the screen or the screen goes blank although the power indicator LED is still on The mess
65. the back of your Monitor DVI IN Connected to a Macintosh Connect the monitor to the Macintosh computer using the D sub connection cable Turn on your computer and monitor If your monitor displays an image installation is completed Connecting Cables Using the Stand 3 Using the Stand Folding the base You can tilt the monitor upwards at an angle of 0 to18 The color and appearance of the product may vary depending on the model and the product specifica tions are subject to change without prior notice for reasons of performance enhancement B Safety Precautions E Introduction Connections m Using the Software Adjusting the Monitor Troubleshooting B Specifications a Information O Using the Software Monitor Driver Natural Color MagicTune 3 Monitor Driver When prompted by the operating system for the monitor driver insert the CD ROM included with this monitor Driver installation is slightly different from one operating system to another Follow the directions appropriate for the operating system you have Prepare a blank disk and download the driver program file at the Internet web site shown below Internet web site http www samsung com Worldwide http www samsung com monitor U S A http www sec co kr monitor Korea http www samsungmonitor com cn China Installing the Monitor Driver Automatic Insert the CD into the CD ROM drive Click Windows C
66. tings Set the video card by referring to the video card manual Install the monitor driver according to the Driver Installation Instructions Install the monitor driver according to the Driver Installation Instructions To check whether your PC is available for MagicTune feature follow the steps below When Windows is XP Control Panel gt Performance and Maintenance gt System Hardware Device Manager Monitors After deleting Plug and Play monitor find Plug and Play monitor by searching new Hardware MagicTune is an additional software for the monitor Some graphic cards may not support your monitor When you have a problem with the graphic card visit our website to check the compatible graphic card list provided http www samsung com monitor magictune MagicTune Have you changed Download the latest program The program can be doesn t work your PC or video downloaded http www samsung com monitor magictune properly graphic card Did you install the Reboot the computer after installing the program for the program first time If a copy of the program is already installed remove it reboot the computer and then install the program again You need to reboot the computer for it to operate normally after installing or removing the program Visit the MagicTune website and download the installation software for MagicTune MAC D Check the following items if there is trouble with the m
67. tional items Unpacking Monitor Manual ro Warranty Card User s Guide Monitor Driver Quick Setup Guide Not available in all Natural Color software locations MagicTune software Cable Power Cord D sub Cable D Others Cleaning Cloth Will be applied to black and high gloss models only GO Sold separately DVI Cable 3 Your Monitor G Front Package Contents Your Monitor MENU button M MagicBright button aa o O Open the OSD menu Also use to exit the OSD menu or return to the previous menu MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching Currently seven different modes are available Custom Text Internet Game Sport Movie and Dynamic Contrast Each mode has its own pre configured brightness value You can easily select one of seven settings by simply pressing MagicBright control button 1 Custom Although the values are carefully chosen by our engineers the pre configured values may not be comfortable to your eyes depending on your taste If this is the case adjust the brightness and contrast by using the OSD menu 2 Text For documentations or works involving heavy text 3 Internet For working with a mixture of images such as texts and graphics 4 Game For watching motion pictures such as a game 5 Sport For watching motion pictures such as a sport
68. uration at the back of the monitor may vary from product to product POWER port DVI IN port RGB IN port G 00 Kensington Lock Connect the power cord for your monitor to the power port on the back of the monitor Connect the DVI Cable to the DVI IN port on the back of your monitor Connect the signal cable to the 15 pin D sub port on the back of your monitor The Kensington lock is a device used to physically fix the system to something when using it in a public place The locking device has to be purchased separately For using a locking device contact the place of purchase See Connecting Cables for further information regarding cable connections SyncMaster 732NPlus 732N Model The color and appearance of the product may vary depending on the model and the product specifica tions are subject to change without prior notice for reasons of performance enhancement Safety Precautions E Introduction Connections m Using the Software E Adjusting the Monitor 2 Troubleshooting E Specifications E Information O Connections Connecting Cables Using the Stand ID Connecting Cables Rear of Monitor Rear of Computer Macintosh SAMSUNG Connect the power cord for your monitor to the power port on the back of the monitor Plug the power cord for the monitor into a nearby outlet E Use a connection appropriate to the computer you are using Using the D sub Analog connector on the vid
69. ure a clear image The Interlace method is the same as that used in TVs G Plug 8 Play This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically This monitor follows the international standard VESA DDC for the Plug amp Play function Resolution The number of horizontal and vertical dots used to compose the screen image is called the resolution This number shows the accuracy of the display A high resolution is good for performing multiple tasks as more image information can be shown on the screen Example If the resolution is 1280 x 1024 this means the screen is composed of 1280 horizontal dots horizontal resolution and 1024 vertical lines vertical resolution Contact SAMSUNG WORLDWIDE Terms For Better Display Authority 3 For Better Display Adjust computer resolution and screen injection rate refresh rate oncomputer as described below to enjoy the best quality of picture You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT LCD gt Resolution 1280 x 1024 gt Vertical frequency refresh rate 60 Hz TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm one millionth above is used for this product But the pixels of RED GREEN BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen This
70. ustments See PowerSaver described in the manual for further information regarding power saving functions For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods Rear SAMSUNG The configuration at the back of the monitor may vary from product to product POWER port Connect the power cord for your monitor to the power port on the back of the monitor RGB IN port Connect the signal cable to the 15 pin D sub port on the back of your monitor E Kensington Lock The Kensington lock is a device used to physically fix the system to something when using it in a public place The locking device has to be purchased separately For using a locking device contact the place of purchase See Connecting Cables for further information regarding cable connections SyncMaster 932BPlus 932B Model Poy The color and appearance of the product may vary depending on the model and the product specifica tions are subject to change without prior notice for reasons of performance enhancement u Safety Precautions E Introduction u Connections m Using the Software E Adjusting the Monitor Troubleshooting E Specifications E Information O Introduction Package Contents Your Monitor 3 Package Contents Please make sure the following items are included with your monitor If any items are missing contact your dealer Contact a local dealer to buy op

Samsung 932B

Contents

Download Pdf Manuals

Related Search

Related Contents