Euro Seat 2 Seating Basic Operating Instructions
Contents
1. 11 MANUAL RECLINE Figure 3 Manual Recline Seatback Adjustment Figure 4 Minimum and Maximum Manual Recline Angles www pridemobility com Euro Seat 2 12 Basic Operation Instructions Seat Angle Dump Adjustment Your seat may be equipped with a mechanism that allows you to adjust the seat angle dump from 5 to 10 in 2 5 increments To adjust the seat angle dump 1 Remove the occupant from the power chair 2 Remove the seat angle adjustment bolt See figure 5 3 Adjust the seat to the desired angle 4 Reinstall the seat angle adjustment bolt Figure 5 Seat Angle Dump Adjustment Euro Seat 2 www pridemobility com Basic Operation Instructions Seat Width Adjustment You can adjust the seat width from 40 6 to 50 8 cm 16 in to 20 in To adjust the seat width 1 Ze 3 4 5 6 Remove the seat cushion Loosen the armrest receiver hardware See figure 6 Reposition the armrest receiver to the desired seat width Tighten the armrest receiver hardware Adjust the width of the other armrest if necessary Replace the seat cushion Leg Rest Width Adjustment You can adjust the leg rest width from 40 6 to 50 8 cm 16 in to 20 in To adjust the leg rest width 1 2 3 Remove the seat cushion Loosen the leg rest receiver hardware See figure 7 Reposition the leg rest receiver to the desired seat2. be equipped with a positioning belt that can be adjusted for operator comfort See figure 16 The positioning belt is designed to support the operator so that he she does not slide down or forward in the seat The positioning belt is not designed for use as a restraining device in a motor vehicle WARNING The positioning belt is not designed for use asa A seat belt in a motor vehicle Nor is your power chair ANN suitable for use as a seat in any vehicle Anyone traveling 4 y ina vehicle should be properly belted into seats approved by the vehicle manufacturer To install the positioning belt 1 Insert the screw through the washer and the mounting tab at the end of the positioning belt See figure 16 2 Install the screw through the steel spacer washer and then the seatback including the large zinc spacer 3 Install the washer and nut to the assembly and then tighten the nut using two adjustable wrenches 4 Repeat steps 1 3 for the other side To adjust the positioning belt 1 Once seated insert the metal tab on one side of the belt into the plastic housing on the opposite side until you hear a click 2 Pull the excess strap attached to the metal tab until it is secure but not so tight as to cause discomfort Euro Seat 2 www pridemobility com Basic Operation Instructions 21 To release the positioning belt 1 Press the push button mechanism on the plastic housing MANDATORY Make sure the positioning belt is prop
3. power chair owner s manual WARNING Should the fittings on your Euro Seat 2 become loose report the problem immediately to your authorized Pride Provider WARNING Pride does not recommend using the Euro Seat 2 as a Seat in a motor vehicle The user should transfer into the vehicle seat and use the vehicle installed belt restraint system if and whenever feasible If your mobility device is equipped with a manufacturer installed transit securement system please refer to the supplemental safety information provided with your mobility device x N WARNING Do not exceed the weight capacity listed in your power 4 N chair owner s manual or 136 kg 300 Ibs whichever is less WARNING Extreme temperatures can affect the temperature of Euro Seat 2 components and may cause skin irritation Use caution when your power chair has been used or stored in an extremely hot or cold environment WARNING Standard foam cushions and other body supports are not designed for the relief of pressure If you suffer from pressure sores or if you are at risk for pressure sores you may need a specialized seating system or a device to control your posture Consult your doctor or therapist to determine if you need such a device for your well being www pridemobility com Euro Seat 2 8 Basic Operation Instructions HEADRESTS ARMRESTS Available in two basic styles EURO HEADREST QUANTUM HEADREST DROP IN ARMREST LINE BACKS MANUAL REC
4. rain snow ice salt or standing water whenever possible Maintain and store in a clean and dry condition WARNING Pride strongly recommends that you do not smoke cigarettes while seated in your Euro Seat 2 although the seating system has passed the necessary testing requirements for cigarette smoking You must adhere to the following safety guidelines if you decide to smoke cigarettes while seated in your seating system Y Do not leave lit cigarettes unattended E Keep ashtrays a safe distance from the seat cushions Always make sure cigarettes are completely extinguished before disposal WARNING Never use any chemicals to clean a vinyl seat as they may cause the seat to become slippery or dry out and crack Use soapy water and dry the seat thoroughly WARRANTY Refer to your power base owner s manual for warranty information www pridemobility com Euro Seat 2 APPENDIX I SPECIFICATIONS Euro Seat 2 Specifications Table Seat Weight Manual Recline 16 in seat 29 71 kg 65 5 lbs Sling Back 18 in seat 35 61 kg 78 5 lbs Solid Back 20 in seat 36 74 kg 81 0 lbs Solid Back Power Tilt 16 in seat 31 07 kg 68 5 lbs Sling Back 18 in seat 37 19 kg 82 0 lbs Solid Back 20 in seat 38 33 kg 84 5 Ibs Solid Back Power Recline 16 in seat 36 51 kg 80 5 Ibs Solid Back 18 in seat 36 97 kg 81 5 Ibs Solid Back 20 in seat 38 10 kg 84 0 Ibs Solid Back Power Tilt Power Recline 16
5. BASIC OPERATION INSTRUCTIONS Euro Seat 2 Mobility Products Corp SAFETY GUIDELINES WARNING An authorized Pride Provider or a qualified 4 N technician must perform the initial setup of this product d and must perform all of the instructions in this manual The symbols below are used throughout this owner s manual and on the product to identify warnings and important information It is very important for you to read them and understand them completely WARNING Indicates a potentially hazardous condition TN situation Failure to follow designated procedures can 4 N cause either personal injury component damage or K malfunction On the product this icon is represented as black symbol on a yellow triangle with a black border MANDATORY These actions should be performed as N specified Failure to perform mandatory actions can cause personal injury and or equipment damage On the product A this icon is represented as a white symbol on a blue dot with a white border PROHIBITED These actions are prohibited These actions should not be performed at any time or in any circumstances Performing a prohibited action can cause personal injury and or equipment damage On the product this icon is represented as a black symbol with a red circle and a red slash NOTE These instructions are compiled from the latest specifications and product information available at the time of publication
6. LINE With this option the seatback can be manually adjusted between 90 and POWER RECLINE With this option the seatback can be adjusted between 90 and 135 Figure 1 Euro Seat 2 Components Euro Seat 2 www pridemobility com Basic Operation Instructions 9 COMFORT ADJUSTMENTS There are several adjustments that can be made to the Euro Seat 2 to increase your comfort such as seat height and angle armrest position and controller position WARNING The center of gravity of your seating system was factory set to a position that meets the needs of the demographic majority of users Your authorized Pride Provider has evaluated your seating system and made any necessary adjustments to suit your specific requirements Do not change your seating configuration without first contacting Pride Mobility Products or your authorized Pride Provider ff NI WARNING Some power chair components are heavy You Y may need assistance to lift or carry them Please refer to d the specifications table for specific component weights before you disassemble the power chair WARNING Remove the occupant from the power chair before making any adjustments WARNING Be sure that the controller s power is turned off and the power chair is not in freewheel mode before performing any adjustment procedures You may need the following to make comfort adjustments E metric standard socket set and ratchet E adjustable wrench E metric standar
7. We reserve the right to make changes as they become necessary Any changes to our products may cause slight variations between the illustrations and expla nations in this manual and the product you have purchased The latest current version of this manual is available on our website CE O ACN 088 609 661 Copyright O 2010 Pride Mobility Products Corporation INFMANU3835 Rev B May 2010 Euro Seat 2 www pridemobility com TABLE OF CONTENTS LABEL INFORMATION 4 INTRODUCTION 5 THE EURO SEAT 2 7 PRECAUTIONARY GUIDELINES 7 COMFORT ADJUSTMENTS 9 CONTROLLER POSITION 18 POSITIONING BELT cias 20 POWER ACCESSORIES 22 CARE AND MAINTENANCE 23 WARRANTY cicala 23 APPENDIX SPECIFICATIONS 24 www pridemobility com Euro Seat 2 LABEL INFORMATION PRODUCT SAFETY SYMBOLS The symbols below are used on the seating system to identify warnings mandatory actions and prohibited actions It is very important for you to read and understand them completely e Read and follow the informati
8. d hex key set Seat Height and Angle Adjustment The Euro Seat 2 is usually connected to a power base with four steel towers You can change the seat height by raising these towers If you raise or lower only one set of seat towers front or rear you can also change the seat base angle To change the seat height or seat angle 1 Remove the retaining pin from each of the four seat mount connectors See figure 2 2 Raise or lower each seat tower to the desired position To change the angle set either the front or rear seat towers higher or lower than the other 3 Reinstall the retaining pin into each seat mount connector www pridemobility com Euro Seat 2 Basic Operation Instructions 10 CONNECTOR Figure 2 Seat Height Angle Adjustment www pridemobility com Euro Seat 2 Basic Operation Instructions Manual Recline Seatback Adjustment Your seat may be equipped with a manual recline lever that allows you to adjust the seatback angle from the minimum recline position 90 from the seat base to the max imum recline position 135 from the seat base See figures 3 and 4 To adjust the seatback angle 1 With your back pressed firmly against the seatback squeeze the manual recline lever mounted to the armrest See figure 3 2 Set the seatback at the desired angle by leaning forward or back 3 Release the manual recline lever when the seatback is at the desired angle
9. ee figure 14 Slide the controller out of the loosened clamp assembly Loosen the setscrews on the clamp assembly on the other armrest Remove the manual recline lever assembly and insert it into the clamp assembly on the opposite armrest See figure 3 8 Tighten the setscrews to secure the manual recline lever assembly in the figure 8 clamp 9 Insert the controller into the remaining open clamp assembly 10 Tighten the setscrews to secure the controller in the figure 8 clamp qe o LONA Euro Seat 2 www pridemobility com Basic Operation Instructions 19 11 Use wire ties to secure the controller harness and the manual recline lever cable to your seating system 12 Route the controller harness along the seat frame and reconnect the controller See figure 15 To change the controller extension 1 Turn off the power to the controller 2 Loosen the setscrews on the mounting assembly located on the armrest See figure 13 or 14 3 Slide the controller into or out of the mounting assembly to the desired position 4 Tighten the setscrews to secure the controller in the mounting assembly FIGURE 8 MOUNTING BLOCK _ jo Se CLAMP MOUNTING SCREWS ASSEMBLY Figure 13 Controller Position Figure 14 Controller Position Adjustment Mounting Block Adjustment Figure 8 Assembly Figure 15 Harness Routing www pridemobility com Euro Seat 2 20 Basic Operation Instructions POSITIONING BELT Your Euro Seat 2 may
10. erly secured to the seating system and is adjusted for operator TN comfort before each use a MANDATORY Inspect the positioning belt for loose or damaged parts before each use of the power chair If you discover a problem contact your authorized Pride Provider for maintenance and repair DEN t WASHER SCREW ZINC SPACER Figure 16 Positioning Belt Attachment www pridemobility com Euro Seat 2 22 Basic Operation Instructions POWER ACCESSORIES Your Euro Seat 2 may be equipped with optional power positioning such as a power tilt power recline and power front riggings Refer to the supplemental controller information supplied with your power chair owner s manual for instructions on how to operate power accessories See figures 17 and 18 for range of motion of the power tilt and recline Figure 18 Euro Seat 2 Power Recline Range of Motion NOTE When the seat is tilted or reclined past 120 an inhibit switch will cut power to the motors of your power chair Returning the seat to an angle of less than 120 degrees will restore power to the motors Euro Seat 2 www pridemobility com Basic Operation Instructions 23 CARE AND MAINTENANCE EH Make sure all hardware is secured properly but do not overtighten any hardware MB To clean the Euro Seat 2 wipe it with a cloth dampened with mild soap and water Thoroughly dry the unit before using PROHIBITED Avoid exposure to
11. in seat 38 10 kg 84 0 Ibs Solid Back 18 in seat 38 56 kg 85 0 lbs Solid Back 20 in seat 39 69 kg 87 5 lbs Solid Back 16 in x 16 in 16 in x 18 in 18 in x 18 in 20 in x 20 in Seat Upholstery Drop in Headrests Euro style Quantum Headrest optional 2 styles Weight Capacity 136 kg 300 Ibs Back Height Euro Seat 2 www pridemobility com NOTES www pridemobility com Euro Seat 2 NOTES Euro Seat 2 www pridemobility com NOTES www pridemobility com Euro Seat 2 Pride Mobility Products Corp Pride Mobility Products Corporation 182 Susquehanna Avenue Exeter PA 18643 2694 USA Pride Mobility Products Company 380 Vansickle Road Unit 350 St Catharines Ontario L2R 6P7 Canada Pride Mobility Products Ltd 32 Wedgwood Road Bicester Oxon OX26 4UL UK Pride Mobility Products Australia Pty Lid 21 Healey Road Dandenong 3175 Victoria Australia Pride Mobility Products Italia S r l Via del Progresso ang Via del Lavoro Loc Prato della Corte 00065 Fiano Romano RM Pride Mobility Products Europe B V Castricummer Werf 26 1901 RW Castricum The Netherlands NFMANU3835
12. increase your ability to use and enjoy your Pride product NOTE If you ever lose or misplace your product registration card or your copy of this manual contact us and we will be glad to send you a new one immediately My Authorized Pride Provider Is Name Address Phone Number Purchase Date Euro Seat 2 www pridemobility com Basic Operation Instructions 7 THE EURO SEAT 2 The Euro Seat 2 is a unique seating system designed specifically for the Pride Power Chair It is fully adjustable to meet the individual needs of the user and it 15 mounted to a Pride power base to provide maximum maneuverability Reusable hook and loop fasteners are included in your owner s package for use in attaching the seat cushion to the seat base These fasteners are not intended for use on cushions with anti skid material as they may damage the seat cushion Figure 1 provides information on Euro Seat 2 components Use this diagram to familiarize yourself with the function and location of each component before using the Euro Seat 2 PRECAUTIONARY GUIDELINES Before using the Euro Seat 2 please read the following These guidelines are provided for your benefit and will aid you in the safe operation of the seating system Turn off the power before you are seated in the Euro Seat 2 Always have assistance when you are being seated in the Euro Seat 2 E Follow all of the procedures and heed the warnings as explained in your
13. ls The top height adjustment range is 7 62 cm 3 in in 0 95 cm 3 8 in increments The bottom height adjustment range is 7 62 cm 3 in in 2 54 cm 1 in increments Figure 8 Armrest Removal installation POSITION POSITION To remove the armrest assembly 1 Rotate the armrest lock lever forward See figure 8 2 Lift up the armrest assembly Euro Seat 2 www pridemobility com Basic Operation Instructions To install the armrest assembly 1 2 Place the armrest assembly into the armrest lock See figure 8 Rotate the armrest lock lever rearward To adjust the top height 1 2 If present remove the optional locking pin See figure 9 Pull the armrest up to raise or press the release lever to lower the armrest to the desired height If applicable reinsert the locking pin Repeat for the other armrest if necessary To adjust the bottom height 1 gt Remove the two button head screws from the detent bar See figure 10 Slide the armrest up or down Line up the holes in the armrest Reinstall the two button head screws into the detent bar Repeat for the other armrest if necessary www pridemobility com 15 Figure 9 Armrest Top Height Adjustment BUTTON HEAD SCREWS ARMREST LOCK LEVER Figure 10 Armrest Bottom Height Adjustment Euro Seat 2 16 Headrest Adjustment Your seat is equipped with either a Euro style or Quantum style headrest T
14. o adjust the Euro style headrest height 1 Loosen the headrest receiver lock lever See figure 11 2 Slide the headrest up or down to the desired position 3 Tighten the headrest receiver lock lever to secure the headrest to the desired position To adjust the height depth or angle of the headrest 1 Loosen the adjustment screws that correspond to the desired adjustments See figure 12 Position the headrest to the desired position Tighten the adjustment screws Basic Operation Instructions RECEIVER LOCK ANA LEVER a Di i Figure 11 Euro style Headrest Height Adjustment NOTE Once adjustments have been made and the headrest is in the desired position make sure that all of the hardware is tight Euro Seat 2 Y WARNING Do not extend the overall headrest height more 4 than 17 78 cm 7 in above the headrest bracket www pridemobility com Basic Operation Instructions 17 HORIZONTAL ANGLE ADJUSTMENT HEIGHT ADJUSTMENT Figure 12 Quantum style Headrest Adjustments www pridemobility com Euro Seat 2 18 Basic Operation Instructions CONTROLLER POSITION You can position the controller for either left hand or right hand use You can also adjust the extension of the controller from the armrest MANDATORY Prevent controller harness damage Avoid routing the controller harness on the outside of the armrest pad Route the harness under the arm
15. on in the owner s manual K EN Avoid exposure to rain snow ice salt or standing water whenever possible Maintain and store in a clean and dry AS condition EMI RFI This product has been tested and passed at an immunity level of 20 V m Use correct tie down points for controller harness to prevent the harness from getting caught in the drive tires FO pinched in the seat frame or damaged when passing 0 o through doorways Indicates that tested and ai approved seating system Refer to Manual for approved conforms to ISO 7176 19 requirements product configuration s Euro Seat 2 www pridemobility com Basic Operation Instructions 5 INTRODUCTION WELCOME to Pride Mobility Products Pride The product you have purchased combines state of the art components with safety comfort and styling in mind We are confident that the design features will provide you with the conveniences you expect during your daily activities Understanding how to safely operate and care for this product should bring you years of trouble free operations and service Read and follow all instructions warnings and notes in this manual before attempting to operate your product for the first time You must also read all instructions warnings and notes contained in any supplemental instruc tional booklets for the controller front riggings and or seating system that accompanied your power chair before initial operation You
16. r safety depends upon you as well as your provider caretaker or healthcare profes sional in using good judgement This manual is to be used in addition to the power base owner s manual that came with your power chair If there is any information in this manual which you do not understand or if you require additional assistance for setup or operation please contact your authorized Pride Provider Failure to follow the instructions warnings and notes in this manual and those located on your Pride product can result in personal injury and or product damage and will void Pride s product warranty PURCHASER S AGREEMENT By accepting delivery of this product you promise that you will not change alter or modify this product or remove or render inoperable or unsafe any guards shields or other safety features of this product fail refuse or neglect to install any retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product INFORMATION EXCHANGE We want to hear your questions comments and suggestions about this manual We would also like to hear about the safety and reliability of your new Pride product and about the service you received from your authorized Pride Provider www pridemobility com Euro Seat 2 6 Basic Operation Instructions Please notify us of any change of address so we can keep you apprised of important information about safety new products and new options that can
17. rest or toward the N inside of the armrest pad Use correct tie down points for se the controller harness to prevent the harness from getting caught in the drive tires pinched in the seat frame or damaged when passing through doorways NOTE Your controller will be attached either by a mounting block or a figure 8 assembly Be sure to follow the correct set of instructions below when changing the position of your controller To change the controller position in a mounting block 1 Turn off the power to the controller 2 Unplug the controller connector from the power base Refer to your power chair owner s manual 3 Remove any wire ties securing the controller harness to the armrest 4 Loosen the mounting screws in the controller mounting block See figure 13 5 Move the controller mounting block and controller to the other armrest and tighten the mounting screws 6 Use wire ties to secure the controller harness and the manual recline lever cable to the armrests 7 Route the controller harness along the seat frame and reconnect the controller to the power base See figure 15 To change the controller position in a figure 8 assembly 1 Turn off the power to the controller 2 Unplug the controller connector from the power base Refer to your power chair owner s manual Remove any wire ties securing the controller harness to the armrest Loosen the setscrews on the figure 8 clamp assembly located on the armrest S
18. width Tighten the leg rest receiver hardware Adjust the width of the other leg rest if necessary Replace the seat cushion 13 Figure 7 Leg Rest Width Adjustment www pridemobility com Euro Seat 2 14 Basic Operation Instructions WARNING Do not attempt to lift or move your power chair or seating system by any of its removable parts including the armrests front riggings seat cushions seatback shrouds or controller Use only solid non removable frame components to lift or move your power chair or seating system WARNING Avoid putting all of your weight on the Euro Seat A 2 armrests and do not use the armrests for weight bearing Y purposes such as transfers Such use may cause the power chair to tip resulting in a fall from the power chair personal injury Re WARNING The controller and controller bracket are load bearing items on your seating system Do not use the controller or controller bracket for weight bearing puposes such as transfers Such use may cause damage to these components resulting in a fall from the seating system and personal injury Armrest Height Adjustment Armrest height adjustments can be made on both the top and the bottom of the armrest The total height adjustment range is 15 24 cm 6 in from 27 94 43 18 cm 11 17 in This range is measured from the seat pan to the top of the armrest pad Top height adjustments do not require any too
Download Pdf Manuals
Related Search