SW VGA-Ars Rev E.pmd
Contents
1. Introduction cont d et SW VGArs Ars Series Switchers 9 Chapter Two Installation Installation Overview Mounting the Switcher Rear Panel Features and Connections 1 4 SW VGArs Ars Series Switchers Introduction Mounting the Switcher NOTE If you are going to connect VSW I AAP remote controls to one or more inputs identify the version of the SW VGArs Ars circuit board to ensure that the VSW I AAPs will work with this version and configure the switchers jumpers before mounting the switcher See Identifying the Board Version and Setting the SW VGA Ars Jumpers on page 2 10 Rack mounting UL requirements The following Underwriters Laboratories UL requirements pertain to the installation of the switcher into a rack figure 2 1 1 Elevated operating ambient If installed in a closed or multi unit rack assembly the operating ambient temperature of the rack environment may be greater than room ambient Therefore consider installing the equipment in an environment compatible with the maximum ambient temperature Tma specified by the manufacturer Reduced air flow Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised Mechanical loading Mounting of the equipment in the2. Mount the switcher See Mounting the Switcher the next page Attach the cables See Rear Panel Features and Connections later in this chapter E Connect power cords and turn on the devices in the following order C e Output devices projectors monitors speakers e SW VGArs Ars Series switcher e Contact closure RS 232 controller e Input devices computers audio sources Select an input using the front panel buttons or the contact closure or RS 232 controller The picture should now appear and sound should be audible SW VGA Ars models If not Ensure that all devices are plugged in and receiving power e Check the cabling and make adjustments as needed e Select a different input that is known to work to check for a display and sound 2 2 SW VGArs Ars Series Switchers Installation Furniture mounting All of the switcher models can be mounted under furniture such as a table or podium surface using optional MBU 125 under desk mounting brackets 70 077 01 All models can also be mounted through a table or podium using optional Installation cont d Installation instructions For optional rack mounting mount the SW VGArs Ars Series on an optional RSU 129 1U Universal Rack Shelf part 60 190 01 or RSB 129 1U Basic Rack Shelf part 60 604 01 figure 2 1 The switcher mounts either to the right or to the left at the front of the rack MBD 129 through desk moun
3. Remote asicor vindi vovisas o Hisce ka ax HCE PY OR KH EPFL EEFEE Identifying the Board Version and Setting the SW VGA Ars Jumpers Configuring trie switcher aep x asbeno texit ive ret UOn is a E ObEas Chapter 3 Operation sees Front Panel Controls and Indicators Front panel buttons and 1525 sse Front Panel Operations Normal and auto switch modes ssssesse Viewing the current switch mode Selecting normal switch mode ss Selecting auto switch MOE esse Selecting an input in normal switch mode SW VGArs Ars Series Switchers Table of Contents Quick Start Guide SW VGArs Ars Series cont d Input selection normal switch mode Select an input using the front panel buttons shown below or the contact closure or RS 232 controller switcher must be in normal switch mode The selected input s LED lights 1 2 3 4 5 6 Ho MODE NORMAL AUTO Input selection auto switch mode When the switcher is in auto switch mode it switches to the highest numbered input with a sync signal present The selected input s LED lights If no input has sync signals present no input is selected and no input LED lights Switch mode s
4. A E Zit FA VE YE A mu par EE uet np EKRE A aE fo HL Uh HE f DRE WEBS HH P LEO ETE AE A CLINT TP BL 8 TEUER 7 EL AEA EU WAFL 6 SALE ES 41 5 H A LU B DL MERCIER Bj LEAL PS ABR FORET ETSI T EY OE LL o SEPA SURUT Pg EDI ANTE fa 7 SE fcrt Fa MENE RU TES D EL ARUBA BAW AG FR eee EY AB rag FR AEP Wn PEHA ah Hae LH IM OE 3 o 5 VARESE S Ber FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense NOTE This unit was tested with shielded cables on the peripheral devices Shielded cables must be u
5. Chapter Four Remote Control Simple Instruction Set Control Windows Based Program Control VSW AAP Remote Control Contact Closure Remote Control IR 102 Infrared Remote Control 3 4 SW VGArs Ars Series Switchers Operation Switcher initiated unsolicited messages When a local event such as a front panel operation or error condition occurs the switcher responds by sending a message to the host The switcher initiated messages are listed below C Copyright 2002 Extron Electronics SWy VGArs Vx xx a The switcher issues the copyright message when it first powers on Vx xx is the firmware version number Inne All 41 The switcher issues the Inn message when a front panel input selection operation occurs n is the input number Reconfig The switcher initiates this message when there is a change in an audio model s audio gain setting Sigenenenenenen a The switcher initiates this message when there is a change in the status of an input n 1 indicates the video signal is present n 0 indicates the video signal is not present There are as many ns in the switcher initiated message as the maximum number of inputs for the models 2 4 or 6 For example the response Sige1e1 e1 e0 19 0 shows that the input signal is present on inputs 1 2 3 and 5 and that no signal is present on inputs 4 and 6 Error responses When the switcher receives a valid SIS command it executes the command and sends a respo
6. rack should be such that a hazardous condition is not achieved due to uneven mechanical loading Circuit overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring Appropriate consideration of equipment nameplate ratings should be used when addressing this concern Reliable earthing grounding Reliable earthing of rack mounted equipment should be maintained Particular attention should be given to supply connections other than direct connections to the branch circuit such as the use of power strips SW VGArs Ars Series Switchers Installation 2 3 Installation Installation Overview To install and set up the SW VGArs Ars Series switchers follow these steps 1 Turn all of the equipment off Ensure that the video and audio sources computers stereos tape decks or other devices the SW VGArs Ars switcher the output devices projectors speakers and contact closure control device are all turned off and disconnected from the power source 2 If you are going to connect VSW I AAP remote controls to one or more inputs identify the version of the SW VGArs Ars circuit board to ensure that the VSW I AAPs will work with this version and configure the switcher s jumpers See Identifying the Board Version and Setting the SW VGA Ars Jumpers on page 2 10
7. der Wandsteckdose ziehen Schutz des Netzkabels Netzkabel sollten stets so verlegt werden daf sie nicht im Weg liegen und niemand darauf treten kann oder Objekte darauf oder unmittelbar dagegengestellt werden k nnen Wartung Alle Wartungsmafsnahmen sollten nur von qualifiziertem Servicepersonal durchgef hrt werden Die internen Komponenten des Ger tes sind wartungsfrei Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall dieses Ger t selbst ffnen da beim Entfernen der Abdeckungen die Gefahr eines elektrischen Schlags und oder andere Gefahren bestehen Schlitze und ffnungen Wenn das Ger t Schlitze oder L cher im Geh use aufweist dienen diese zur Vermeidung einer Uberhitzung der empfindlichen Teile im Inneren Diese Offnungen d rfen niemals von anderen Objekten blockiert werden Litium Batterie Explosionsgefahr falls die Batterie nicht richtig ersetzt wird Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen vergleichbaren Batterietyp der auch vom Hersteller empfohlen wird Entsorgen Sie verbrauchte Batterien bitte gemaf den Herstelleranweisungen Advertencia Alimentaci n el ctrica Este equipo debe conectarse nicamente a la fuente tipo de alimentaci n el ctrica indicada en el mismo La alimentaci n el ctrica de este equipo debe provenir de un sistema de distribuci n general con conductor neutro a tierra La tercera pata puesta a tierra es una medida de seguridad no puent
8. eaaus Yes with optional 1U rack shelf part Cabl or 60 604 01 also under desk abies 60 190 01 mountable with mounting kit 70 077 01 Male to male VGA audio cables Part number and through desk with mounting kit 70 077 02 VGA A M M MD 3 2 9 m 26 490 01 Enclosure type sess Metal VGA A M M MD 6 6 1 8m 26 490 02 Enclosure dimensions 1 75 H 8 75 W x 9 5 D VGA A M M MD 12 12 3 6m 26 490 03 1U high half rack wide VGA A M M MD 25 25 7 6 m 26 490 04 4 4 cm H x 22 2 cm W x 24 1 cm D Depth excludes connectors VGA A M M MD 50 50 15 2m 26 490 08 0 Convection unvented Accessories 2 5 Ibs 0 5 kg A BI b Shipping WEINE seisersorseisisiisiss 5 lbs 3 kg peices lta mel iced Vibration 8 ISTA 1A in carton RSU 129 1U Universal rack shelf 60 190 01 International Safe Transit Association RSB 129 1U Basic rack shelf 60 604 01 PAR ETE 0 ae 3 acre MBU 125 Under desk mounting kit 70 077 01 OMIPTAICES MATRE ass A MBD 129 Th h desk ting kit 70 077 02 MTBE ns 30 000 hours ii tae poen d 3 years parts and labor pap aene SY VGA XGA 26 173 01 Ten All nominal levels are at 10 iP M 60 111 20 IR 102 remote control kit 1 3 5 mm stereo plug 10 306 01 eyes Specifications are subject to change without notice A 4 SW VGArs Ars Series Switchers Reference Information SW VGaArs Ars Series Switchers Reference Information A 5 Reference Information cont
9. 232 contact closure connector Connect a computer or RS 232 control module to this 9 pin D connector to allow remote control using the Simple Instruction Set SIS or the Extron graphical control program for Windows see chapter 4 Remote Control for details You may also connect a KP 6 remote control keypad part 60 111 20 or an IR 102 Kit infrared remote control part 70 224 01 system to this connector see figure 2 7 NOTE The switcher can be controlled only by an RS 232 device OR a contact closure device not both The cable used to connect the Remote port to a computer control system contact closure device or IR control kit may need to be modified by removing pins or cutting wires If unneeded pins are connected the switcher may hang up See chapter 4 Remote Control for additional information Contact PIN RS 232 Closure Function 1 In 1 Input 1 TX Transmit data REMOTE RX Receive data In 2 Input 2 Gnd Gnd Ground In 3 Input 3 In 4 Input 4 In 5 Input 5 In 6 Input 6 Co 60 ON DOB OMN Figure 2 7 Remote connector pinout SW VGArs Ars Series Switchers Installation 2 9 Installation cont d Audio SW VGA Ars models only 3 Audio input connector Plug a 3 5 mm stereo plug into this jack for unbalanced audio input Wire the plug as shown in figure 2 5 The number of inputs available varies with the switcher model When making connections
10. 6 mV Video output Maximum level 16 dBu unbalanced at 1 THD N Number signal type 1 VGA UXGA RGBHV RGBS RGsB 0 B RsGsBs computer video and HDTV Meludil 0 dBu 0 775 Vrms OdBV 1 Vrms OdBV 2 dBu component video pU ss suE Ev maie bns 1 15 pin HD female Audio output SW 2 4 6 VGA Ars models only Nominal level a 0 7 Vp p for RGB Number signal 76 1 stereo balanced unbalanced Minimum maximum levels 0 3 V to 1 5 Vp p follows input basi oe etas 1 3 5 mm captive screw connector 5 pole Impedance esrus 75 ohms Impe dHOB oondsestuso danh iue terres 50 ohms unbalanced 100 ohms balanced Return loss a 43 dB 5 MHz Nominal level ierra 4 dBu 1 23 V balanced DC ONSET 5 mV maximum with input at 0 offset 4 dBV 0 63 V unbalanced Maximum level Hi Z 28 dBu balanced 20 dBV unbalanced Sync at 1 THD N trente sreis RGBHV RGBS RGsB RsGsBs bi level Maximum level 600 ohm 21 dBm balanced 18 dBm unbalanced at 1 THD N and tri level sync on Y OUD UE By DO Er RGBHV RGBS RGsB RsGsBs bi level Control remote switcher and tri level sync on Y follows input 1 0 V to 5 0 Vp p Derral COMO DOLE serenan RS 232 9 pin female D connector shared iode vetet 698 with contact closure Output leve larseni TTL 5 0 Vp p unterminated Baud rate and protocol 9600 baud 8 data bits 1 st
11. 69 P 120 of SE P Extron Electronics INTERFACING SWITCHING AND DISTRIBUTION User s Manual Extron SW VGA Ars SERIES VGA AUDIO SWITCHER 6 AUTO SWITCH ACTIVE NORMAL AUTO i INPUTS a n a ERU uum REMOTE SW6 VGA Ars 1 E 5 OUTPUT 4 x Jh oC Jo of pp gureur pru Extron SW VGA Ars SERIES VGA AUDIO SWITCHER 6 AUTO SWITCH ACTIVE NORMAL AUTO sedas BE EUN uum REMOTE SW6 VGArs NL Xue of Gp 6 gt OUTPUT ol jo 1 P SW VGA Ars Series SW2 VGArs SW2 VGA Ars SW4 VGArs SW4 VGA Ars SW6 VGArs SW6 VGA Ars 68 646 01 Rev E 06 07 Extron Electronics Europe Extron Electronics Asia Extron Electronics Japan Beeldschermweg 6C 135 Joo Seng Rd 04 01 Kyodo Building 16 Ichibancho 3821 AH Amersfoort The Netherlands PM Industrial Bldg Singapore 368363 Chiyoda ku Tokyo 102 0082 Extron Electronics USA 1230 South Lewis Street Anaheim CA 92805 800 633 9876 714 491 1500 800 3987 6673 31 33 453 4040 800 7339 8766 65 6383 4400 Japan FAX 31 33 453 4050 FAX 65 6383 4664 81 3 3511 7655 FAX 81 3 3511 2007 Extron Electronics All rights reserved FAX 714 491 1517 c5 AMA Ze Pe 3 uj 9 1209 b 0 o turio www extron com Extron s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase In the event of malfunction during
12. A system products including computer video interfaces switchers matrix switchers distribution amplifiers signal processing devices Ethernet control interfaces and high resolution cable Extron offers solutions for integration of video and audio into presentation systems for a variety of environments such as boardrooms classrooms and training centers lecture halls command and control centers and more For the latest product information visit www extron com M N 3 Products E 0 Software k 4 Find a product and view aS KS Eq Install control and available files N configuration software amp Done X My Computer Figure 5 1 Software CD window SW VGArs Ars Series Switchers Remote Control 4 7 Software version x xx Query software version Remote Control cont d Request for part number auto video not muted audio muted Video input 2 audio input 2 front panel mode V2e A2eFe2eVmt Oe Amt 1 Vlxije A xi e F o xs e V mt x3 e A mt x3 2 Information request un d un 0 fa 0 o 5 E in ud c 66 2 E c E im Q c Q Ex E in e 5 6 gt Set switch mode to auto auto switch Set auto switch mode Set normal switch mode Set switch mode to normal Front panel mode switcher to host host to switcher SW VGArs Ars Series Switchers Remot
13. MAL SW VGA Ars SERIES VGA AUDIO SWITCHER SW VGA Ars SERIES VGA AUDIO SWITCHER 3 4 5 6 mm AUTO Figure 3 1 Front panel SW VGArs and SW VGA Ars front panels are identical Input selection buttons and LEDs When the auto switch mode is off use these buttons to select the input The LED for the selected input lights The LEDs continue to indicate the selected input when auto switch mode is on If no input LED is lit no input has active sync pulses and no input is selected 2 3 2 SW VGArs Ars Series Switchers Operation Operation cont d Ey e 2 3 e SW VGArs Ars Series Switchers Selecting auto switch mode by Press and hold the Input 1 Mode button while you press and curio release the Input 3 Auto button The Auto Switch Active LED turns on indicating auto switch mode Release the Input 1 Mode button Auto switch mode must be disabled when using the switcher with one or more VSW I AAP remote controls If the auto switch mode is enabled the input cannot be selected using the show me function Selecting an input in normal switch mode To select an input using the front panel buttons press and release the button for the desired input must be in normal switch mode The LED for the selected input lights An input can also be selected by an RS 232 device or a remote control device see chapter 4 Remote Control
14. Software version X XX Switch mode 1 normal switch mode 2 auto switch mode ASCII to HEX Conversion Table Esc 1B CR 60 1 A ES 24 5 Qo 6 gt F N V f n V NG OHNICU 4 4 SW VGArs Ars Series Switchers Remote Control Windows Based Program Control The Windows based Extron Universal Switcher Control Program which communicates with the switcher via the RS 232 port provides an easy way to configure and operate the SW VGArs Ars Series switchers The program is compatible with Windows 2000 and Windows XP Installing the software The program is contained on the Extron Software Products CD ROM disk B Install the software as follows 1 Insert the CD ROM into the drive The installation program should start automatically If it does not self start run Launch exe from the CD The Extron software CD window appears figure 5 1 Extron Software CD Microsoft Internet Explorer BAX ar File Edit view Favorites Tools Help Bac P x a A J gt search J Favorites 2 B E 9 Lj rel 33 Address a D index html u Iv Go Links Extron Software Products Extron Electronics 3 bu Software Pro f Products Software Manuals lt click to select product gt 800 633 9876 15 Home Y extron com 4 Contact Us ia Extron Software Products Disc B Issue 2007 1 For more than 20 years Extron Electronics has manufactured professional A
15. Video mute off Video mute status Audio mute on Audio mute off Sig e xz e Kae KA oSigelelele0e19 0 1 In xil All 2 InlxilVid 2 In xi Aud 2 Input selection Select video and audio input Select video input only Select audio input only Input video sensing Request all inputs status Example SW6 VGArs Request one input s status Video Mute Mute video Unmute video Read video mute Audio Mute Mute audio Unmute audio SW VGArs Ars Series Switchers Remote Control Response switcher to host host to switcher ASCII Command Command response table for SIS commands Additional description Command Remote Control cont d Timeout Pauses of 10 seconds or longer between command ASCII characters result in a timeout The command operation is aborted with no other indication Using the command response table The command response table is on the next page Lowercase letters are allowed in the command field only as indicated Symbols are used throughout the table to represent variables in the command response fields Command and response examples are shown throughout the table The ASCII to HEX conversion table below is for use with the command response table Symbol definitions gt CR LF carriage return line feed 0x0D 0A space Input number 0 through 6 0 output mute Input signal status 0 no signal detected 1 signal detected On off status 0 off 1 on
16. a RX Receive data Input 2 Gnd Ground Input 3 Input 4 Input 5 Input 6 Connect power cords and turn on the equipment in the following order output devices such as projectors monitors and or speakers SW VGArs Series switcher contact closure RS 232 controller and input devices such as computers and or audio sources OND OB ORN SW VGArs Ars Series Switchers Quick Start Guide QS 1 Table of Contents Chapter 1 Introduction cece About this Manual suse SW VGArs and SW VGA Ars Series Switchers FS aE BS arate tint cca eacnve seta neanchantieesweatunuesadoniatendaceseetiennees Chapter 2 Installation Installation Overview m8 Mounting the Switcher Rack MMO UNICO ies tnsvatareceossecatsedarsatensctenncaetscessexentantoenteees UL requirements RN TEE EO ste Installation instructions posi ccadsseneccnsviesnentaceiainadsccetacseadetapce F rniture Rear Panel Features and Connections Power 60 6006 nennen nnns 0 7 All models peu E Quo FE cR mers ere dERS Audio SW VGA Ars models only Signal output cOnrectIDI s eeiasosai e autu qus ora dt PUO IU LER DrRE All models eerte knu asd eo tire nero Ene pe n Audio SW VGA Ars models only
17. d A 6 SW VGArs Ars Series Switchers Reference Information
18. d to alertthe userof important operating and maintenance servicing instructions in the literature provided with the equipment This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product s enclosure that may present a risk of electric shock Caution Read Instructions Read and understand all safety and operating instructions before using the equipment Retain Instructions The safety instructions should be kept for future reference Follow Warnings Follow all warnings and instructions marked on the equipment or in the user information Avoid Attachments Do not use tools or attachments that are not recommended by the equipment manufacturer because they may be hazardous Consignes de S curit Francais Ce symbole sert avertir l utilisateur que la documentation fournie avecle mat riel contient des instructions importantes concernantl exploitation et la maintenance r paration Ce symbole sert avertir l utilisateur de la pr sence dansle boitier del appareil de tensions dangereuses non isol es posant des risques d lectrocution Attention Lire les instructions Prendre connaissance de toutes les consignes de s curit et d exploitation avant d utiliser le mat riel Conserver les instructionse Ranger les consignes de s curit afin de pouvoir les consulter l avenir Respecter les avertissements Observer tous les avertissements et consignes marqu
19. de partes que se desean destacar en el contenido de la documentaci n suministrada con los equipos Este s mbolo se utiliza para advertir al usuario sobre la presencia de elementos con voltaje peligroso sin protecci n aislante que puedan encontrarse dentro dela caja o alojamiento del producto y que puedan representar riesgo de electrocuci n Precaucion Leer las instrucciones Leer y analizar todas las instrucciones de operaci n y seguridad antes de usar el equipo Conservar las instrucciones Conservar las instrucciones de seguridad para futura consulta Obedecer las advertencias Todas las advertencias e instrucciones marcadas en el equipo o en la documentaci n del usuario deben ser obedecidas Evitar el uso de accesorios No usar herramientas o accesorios que no sean especificamente recomendados por el fabricante ya que podrian implicar riesgos x ak 2508 PX RUE KEANE 50 ABE USA GLR Ezi WAER XA BARA PUBL FAL PSA IRBE HU PETENTE P Bt H o RAER 4S WRA JN Rs FB JP MEAE AI RE eee BAL fy HE BI TT HAASE ge A fe y I ERREP ZUNA MAMEN ARO SEP gt
20. during shipment Returned units must include the serial number and a description of the problem as well as the name of the person to contact in case there are any questions Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality performance merchantability or fitness for any particular use In no event will Extron Electronics be liable for direct indirect or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage Please note that laws vary from state to state and country to country and that some provisions of this warranty may not apply to you Warning Power sources This equipment should be operated only from the power source indicated on the product This equipment is intended to be used with a main power system with a grounded neutral conductor The third grounding pin is a safety feature do not attempt to bypass or disable it Power disconnection To remove power from the equipment safely remove all power cords from the rear of the equipment or the desktop power module if detachable or from the power source receptacle wall plug Power cord protection Power cords should be routed so that they are not likely to be stepped on or pinched by items placed upon or against them Servicing Refer all servicing to qualified service personnel There are no user serviceable parts inside To preve
21. e Control Additional description ASCiCommand Response Command response table for SIS commands continued Command 4 6 In figure 5 3 indicates that the input signal is present and is selected c indicates that the input signal is present but not selected W indicates that the input signal is not present Click the EN button to refresh the input signal status Using the help system For information about program features you can access the help program in any of the following ways e Click Start Programs Extron Electronics Universal Switcher Help 4 e From within the Windows based switcher control program select Help gt Contents on the task bar e From within the Windows based switcher control program press the F1 key VSW I AAP Remote Control Each input of an SW VGArs Ars Series switcher can be connected to a VSW I AAP passive interface The VSW I AAP features a computer video input and pass through an unbalanced stereo input and pass through and an input select Show Me button Pressing the VSW I AAP s Show Me button causes the switcher to select the input connected via that AAP Projector e s AAP AAP Figure 5 4 VSW I AAP application SW VGArs Ars Series Switchers Remote Control 4 9 Remote Control cont d 2 Click the Software tab figure 5 1 3 Scroll to the desired program and click Install figure 5 2 Un
22. e connector on figure 2 3 and figure 2 4 and each VGA connector 2 and 4 on figure 2 3 and figure 2 4 on the rear panel of the switcher Lift the top cover off of the switcher Remove 2 Lift Cover nuts each side Straight Up of each 9 pin and 15 pin connector Figure 2 8 Removing the cover 2 10 SW VGArs Ars Series Switchers Installation Installation cont d es P SW VGArs Ars Series Switchers 2 lt There are six jumpers on the circuit board numbered JMP5 gt JMP7 JMP9 JMP11 JMP 13 and JMP15 that control connection with one or more VSW I AAP control panels figure 2 9 and figure 2 10 T A OPEN CLOSED All jumpers are set open removed by default The jumpers in the table below must be set closed installeded when a VSW I AAP is connected to the associated input Chapter Three Close the indicated jumpers in the table below to adjust the appropriate settings VSW I AAP VSW I AAP connected to Jumper connected to Jumper Umpui owes ipea impu we Inputs aues mpus smeo inpute Operation Figure 2 10 Jumper positions vs VSW I AAP input connections Front Panel Controls and Indicators These jumpers enable disable VGA connector pin 5 control for each input Close install the jumper for a specific VGA input to allow the VSW I AAP s show me signal to select that input NOTE When an input is not conn
23. earia ni eliminaria Desconexi n de alimentaci n el ctrica Para desconectar con seguridad la acometida de alimentaci n el ctrica al equipo desenchufar todos los cables de alimentaci n en el panel trasero del equipo o desenchufar el m dulo de alimentaci n si fuera independiente o desenchufar el cable del recept culo de la pared Protecci n del cables de alimentaci n Los cables de alimentaci n el ctrica se deben instalar en lugares donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos Reparaciones mantenimiento Solicitar siempre los servicios t cnicos de personal calificado En el interior no hay partes a las que el usuario deba acceder Para evitar riesgo de electrocuci n no intentar personalmente la reparaci n mantenimiento de este equipo ya que al abrir o extraer las tapas puede quedar expuesto a voltajes peligrosos u otros riesgos Ranuras y aberturas Si el equipo posee ranuras o orificios en su caja alojamiento es para evitar el sobrecalientamiento de componentes internos sensibles Estas aberturas nunca se deben obstruir con otros objetos Bater a de litio Existe riesgo de explosi n si esta bater a se coloca en la posici n incorrecta Cambiar esta bater a nicamente con el mismo tipo o su equivalente recomendado por el fabricante Desachar las bater as usadas siguiendo las instrucciones del fabricante Precautions Safety Instructions English Thissymbolisintende
24. ected via a VSW I AAP that input s jumper should be in the default open position Front Panel Operations Each jumper when closed installed allows the switcher to receive the show me signal from the VSW I AAP on that input s VGA connector When a jumper is open removed that input cannot receive the signal Auto switch mode must be disabled when using the switcher with one or more VSW I AAP remote controls If the auto switch mode is enabled the input cannot be selected using the show me function 2 12 SW VGArs Ars Series Switchers Installation 3 Mode button Use this button with either the Auto or the Normal button to manually turn auto switch mode on or off Mode is a secondary function of the Input 1 button 4 Normal button Use this button with the Mode button to manually turn auto switch mode off Normal is a secondary function of the Input 2 button 5 Auto button Use this button with the Mode button to manually turn auto switch mode on On 4 input and 6 input switchers Auto is a secondary function of the Input 3 button Front Panel Operations Plug in all system components and turn on the input devices desktop computers laptops etc and the output monitor Select an input The image should appear on the monitor Normal and auto switch modes All SW VGArs Ars Series switchers can operate in either normal manual switch mode or auto switch mode In auto switch
25. election Select the switch mode as follows 1 Pressing and hold the Input 1 Mode button 2 While holding the Input 1 Mode button press and release either the Input 2 Normal normal switch mode or Input 3 Auto auto switch mode button Release the Input 1 Mode button The Auto Switch Active LED lights when the switcher is in auto switch mode Troubleshooting If the picture does not appear and sound is not audible SW VGA Ars models Ensure that all devices are plugged in and receiving power If the switcher is in auto switch mode ensure that at least one input device is outputting video to the switcher Check the cabling and make adjustments as needed Select a different input that is know to work to check for a display and sound SW VGArs Ars Series Switchers Quick Start Guide 53e SW VGArs Ars Series Switchers Chapter One Introduction About this Manual SW VGArs and SW VGA Ars Series Switchers All trademarks mentioned in this manual are the properties of their respective owners 68 646 01 Rev E 06 07 SW VGArs Ars Series Switchers Table of Contents Switchers Included parts iube rid iain 0 EA 6665507 65 nennen nnne nnns Table of Contents cont d Command response table for SIS commands Chapter 4 gt Remote Control Simple Instruction Set Control Host to switcher communications Switcher initiated unsolicited
26. ion Specifications Max rise fall 4 2 ns 0 Positive or negative follows input Video Audio SW 2 4 6 VGA Ars models only Gr eC E Unity Banc WI EDO usnso cesa open idis 350 MHz 3 dB GAI ene RENE RES Unbalanced output 6 dB Crosstalk occcccssssssssssnssnseneee 68 dB 6 10 MHz aed AA Frequency 0 20 Hz to 20 kHz 0 05 dB Video input THD Noise ioci iens 0 01 1 kHz at nominal level Number signal 76 2 4 or 6 depending on the model MM gt 90 dB at maximum output unweighted VGA UXGA RGBHV RGBS RGsB 9 45 dB 20 kHz 72 dB 1 kHz or below RsGsBs computer video and HDTV 60 Hz component video St h HON once 80 dB 20 Hz to 20 kH oxicticsvsicvarsncsancteowestincseckes 2 4 or 6 depending on the model 15 pin mee tees a dios HD female M Nominal level 22 ptt 0 7 Vp p for RGB Audio impui D AAO VGA Ars models only Vine asc ena level ee Analog 0 3 V to 1 5 Vp p with no offset Number signal type secese 2 4 or 6 depending on the model stereo re ad eet 75 ohms erence Horizontal frequency 15 to dA5 kiz COMME CIOL S een te ont ptm 2 4 or 6 depending on the model Vertical frequency s s s 30 Hz to 170 Hz id mm female stereo mini jacks tip L Return loss sese 40 dB 8 5 MHz ring R sleeve Gnd Input coupling ce DC siia lt 10 ohms unbalanced DC coupled Nominal level 10 dBV 31
27. iversal Switcher 29 031 02 Bu Oct 6 2006 5 3 ME Install Control software for 6 the MAV 62 MMY Switchers YOS Swe Mx SW 4 amp 5 MX SW 6 Component Model 8 10 Plus and AVV Switchers Figure 5 2 Software installation 4 Follow the on screen instructions By default the Windows installation of the Universal Switchers Control Program creates a C Program Files Extron UnivSW and it places four icons into a group folder named Extron Electronics Universal Switcher The four installed icons are e Check for Universal Switcher Updates e Uninstall Universal Switcher e Universal Switcher Control Program e Universal Switcher Help Using the software Run the program as follows 1 Click Start Programs Extron Electronics Universal Switcher Control Pgm 2 Click the comm port that is connected to the switcher s RS 232 port 3 The Extron Universal Switcher Control Program window figure 5 3 displays the input signal status for each input signal present or not present and the selected input a Extron s UNIVERSAL SW Control Progra OEA File Configure e OO w Video PERIERE e Audio ODE el Auto Switch Refresh Input signal Status Figure 5 3 Universal Switcher Control program window SW VGArs Ars Series Switchers Remote Control 4 8 Remote Contr
28. messages Error responses ccccccceeeeeeeesseeeeeeeeeeeeseneeesens e Ra Vae ME Co bU rn Evan RP TONERS ERE Using the command response table Symbol definitions suec oett rr Windows Based Program Control Installing the software sss Using the software ecce Using the help system VSW I AAP Remote Control Contact Closure Remote Control IR 102 Infrared Remote Control Appendix A Reference Information Specifications Part Numbers Features e Up to two four or six inputs depending on the model e Input sensing present or not present and reporting on the RS 232 port e 350 MHz 3 dB bandwidth e Auto switch mode button or remote selectable e O pin contact closure RS 232 remote control connector e Compatible with Extron VSW I AAP VGA Audio input module with the Show Me control button figure 1 2 a Ew Figure 1 2 Typical application with VSW I AAP e Rack and under desk mountable e 1U half rack width enclosure e Internal universal power supply Input output connectors VGA female 15 pin HD e Compatible with VGA SVGA XGA SXGA and UXGA computers e Compatible with Mac and Quadra computers with optional Extron Mac VGA Adapter 26 340 01 SW VGaArs Ars Series Switchers Introduction 1 3 Introduction About this Ma
29. mode the highest numbered input with a sync signal present is automatically selected for output If no sync signal is present no input is selected Input selection by the front panel buttons is blocked while the switcher is in auto switch mode However the front panel LEDs remain functional and the buttons can be used to view or change the mode Viewing the current switch mode You can determine the current switch mode at any time by noting the state of the Auto Switch Active LED This LED is lit if the switcher is in auto switch mode Selecting normal switch mode Press and hold the Input 1 Mode button while you press and release the Input 2 Norm button The Auto Switch Active LED turns off indicating normal switch mode Release the Input 1 Mode button SW VGArs Ars Series Switchers Operation 3 3 Operation Front Panel Controls and Indicators Noia Lhe front panels are identical for the non audio SW VGArs and audio SW VGA Ars models Figure 3 1 shows the controls and indicators on the front panel of the SW6 VGArs Ars Series switchers Front panel buttons and LEDs Auto Switch Active LED When this LED is on it indicates that the auto switch mode is active Extron rn 0 0 E O A 5 MODE NORMAL AUTO SW VGA Ars SERIES VGA AUDIO SWITCHER Extron 1 2 3 4 AUTO SWITCH 5 EN N N cys Ac ve MODE NORMAL AUTO Extron 1 2 AUTO SWITCH 5 NH N ACT VE MODE NOR
30. nse to the host device If the switcher is unable to execute the command because the command is invalid or it contains invalid parameters the switcher returns an error response to the host The error response codes are E01 Invalid input channel number out of range E06 Invalid input channel change auto switch mode active E09 2 1 Invalid function mode parameter E102 Invalid command E13 2 Invalid value out of range E14 2 Illegal command for this configuration SW VGArs Ars Series Switchers Remote Control 4 3 Remote Control The SW VGArs Ars Series switcher s rear panel Remote connector figure 4 1 can be connected to the serial port output of a host device such as a computer or control system to an Extron IR 102 Kit Universal Remote Control OR to a remote contact closure device Other than the IR 102 Kit remote communications with the switcher are via Extron s Simple Instruction Set SIS or Extron s Windows based control program or they can be pin programmed for use with a contact closure device Contact PIN RS 232 Closure Function 1 In 1 Input 1 TX Transmit data REMOTE RX Receive data In 2 Input 2 Gnd Gnd Ground In 3 Input 3 In 4 Input 4 In 5 Input 5 In 6 Input 6 Figure 4 1 Remote connector pinout Co 60 ON OMN The 345 232 protocol of the rear panel Remote connector is 9600 baud 1 stop bit no parity and no flow control The connec
31. nt the risk of shock do not attempt to service this equipment yourself because opening or removing covers may expose you to dangerous voltage or other hazards Slots and openings If the equipment has slots or holes in the enclosure these are provided to prevent overheating of sensitive components inside These openings must never be blocked by other objects Lithium battery There is a danger of explosion if battery is incorrectly replaced Replace it only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions Avertissement Alimentations Ne faire fonctionner ce mat riel qu avec la source d alimentation indiqu e sur l appareil Ce mat riel doit tre utilis avec une alimentation principale comportant un fil de terre neutre Le troisieme contact de mise la terre constitue un dispositif de s curit n essayez pas de la contourner ni de la d sactiver D connexion de l alimentation Pour mettre le mat riel hors tension sans danger d connectez tous les cordons d alimentation de l arri re de l appareil ou du module d alimentation de bureau s il est amovible ou encore de la prise secteur Protection du cordon d alimentation Acheminer les cordons d alimentation de mani re ce que personne ne risque de marcher dessus et ce qu ils ne soient pas cras s ou pinc s par des objets R paration maintenance Faire ex cuter toutes les i
32. nterventions de r paration maintenance par un technicien qualifi Aucun des l ments internes ne peut tre r par par l utilisateur Afin d viter tout danger d lectrocution l utilisateur ne doit pas essayer de proc der lui m me ces op rations car l ouverture ou le retrait des couvercles risquent de l exposer de hautes tensions et autres dangers Fentes et orifices Si le boitier de l appareil comporte des fentes ou des orifices ceux ci servent emp cher les composants internes sensibles de surchauffer Ces ouvertures ne doivent jamais tre bloqu es par des objets Lithium Batterie Il a danger d explosion s ll y a remplacment incorrect de la batterie Remplacer uniquement avec une batterie du meme type ou d un ype equivalent recommande par le constructeur Mettre au reut les batteries usagees conformement aux instructions du fabricant Vorsicht Stromquellen Dieses Ger t sollte nur ber die auf dem Produkt angegebene Stromquelle betrieben werden Dieses Ger t wurde f r eine Verwendung mit einer Hauptstromleitung mit einem geerdeten neutralen Leiter konzipiert Der dritte Kontakt ist f r einen Erdanschlu amp und stellt eine Sicherheitsfunktion dar Diese sollte nicht umgangen oder aufer Betrieb gesetzt werden Stromunterbrechung Um das Ger t auf sichere Weise vom Netz zu trennen sollten Sie alle Netzkabel aus der R ckseite des Ger tes aus der externen Stomversorgung falls dies m glich ist oder aus
33. nual This manual contains information about the Extron SW VGArs Ars Series switchers and how to operate and configure them SW VGArs and SW VGA Ars Series Switchers The SW VGArs Ars Series switchers are two four or six input VGA switchers each with a buffered output and 350 MHz 3 dB bandwidth figure 1 1 They accept VGA SVGA XGA SXGA and UXGA computer video input the VGA Ars models also include audio input and output The SW VGArs and SW VGA Ars Series switchers can also switch Macintosh signals when used with an optional Mac VGA adapter part 36 340 02 Eniron Extron KP 6 Keypad Remote 90659 9 686 5 o Ce Cee Gmo Sound System Projector Figure 1 1 Typical SW VGArs switcher application The switchers are in rack mountable 1U high half rack width metal enclosures with internal universal 100 240 VAC 50 60 Hz power supplies All models have contact closure and RS 232 remote control capability through the 9 pin Remote connector see the Remote connector pinout table on page 4 2 The KP 6 wired remote control and the IR 102 Kit infrared remote control are optional remote controls The KP 6 has a 25 foot cable The IR 102 Kit has an operating range of approximately 30 feet Front panel buttons a contact closure or RS 232 controller or the autoswitching option can be used for input selection 1 2 SW VGArs Ars Series Switchers Introduction
34. ol cont d Contact Closure Remote Control The Remote connector also provides a way to select an input to the switcher using a remote contact closure device Contact closure control uses pins on the Remote connector that are not used by the RS 232 interface The contact closure pin assignments are shown in figure 4 1 on page 4 2 SW VGArs Ars Series Switchers To select a different input number using a contact closure device momentarily short the pin for the desired input number to logic ground pin 5 To force one of the inputs to be always selected leave the short to logic ground in place The short overrides front panel input selections IR 102 Infrared Remote Control The optional Extron IR 102 kit consists of the following components e JR 102 handheld remote control unit e VersaTools IR 102 remote receiver with 3 cable and RS 232 connector Appendix A e IR detector with 6 cable and captive screw connector e External 12 VDC power supply Install and operate the remote control in accordance with the IR 102 User s Guide included with the remote SWO6 VGA Ars Switcher RS 232 8 ES Reference Information Extron t 0 N IR 102 Remote IR 102 Remote Control IR Detector Control Receiver Specifications Part Numbers Figure 5 4 IR 102 Remote application 4 10 SW VGArs Ars Series Switchers Remote Control Reference Informat
35. op bit no parity Input impedar OCs 510 ohms l Serial control pin configurations 2 TX 3 RX 5 GND OULD UT I POCA Ce session 75 ohms l 8 RS 232 9 pin female D connector shared Max propagation delay 47 ns with RS 232 A 2 SW VGArs Ars Series Switchers Reference Information SW VGArs Ars Series Switchers Reference Information A 3 Reference Information cont d Contact closure pin configurations Part Numbers 1 input 1 4 input 2 6 input 3 7 input 4 8 input 5 9 input 6 Switchers so pu witcher M l Part number Sound Switche odels art numbe Show Me contact closure Pin 5 of each VGA input connector The SW2 VGArs 60 257 02 input is active selected when pin 5 SWI STU Bre 08257822 momentarily goes to gound This applies only to units with firmware version 2 00 SW VGArs 60 258 02 or higher SW4 VGA Ars 60 258 22 0 Extron s control configuration program SW6 VGArs 60 259 02 for Windows SW6 VGA A 60 259 22 Extron s Simple Instruction Set SIS Included parts General EUER NN ioe mein ne so ane internal autoswitchable AC power cord Temperature humidity Storage 40 to 158 F 40 to 70 C Tweeker VGA Ars models only 10 to 90 noncondensing Operating 32 to 122 F 0 to 50 C 10 to 90 noncondensing SW VGA Ars Series Switcher User s Manual Universal Switcher Control Program CD esies eii ured i
36. s sur le mat riel ou pr sent s dans la documentation utilisateur Eviter les pi ces de fixation Ne pas utiliser de pi ces de fixation ni d outils non recommand s par le fabricant du mat riel car cela risquerait de poser certains dangers Sicherheitsanleitungen Deutsch Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung Instandhaltung geben DiesesSymbolsollden Benutzer darauf aufmerksam machen da im Inneren des Geh uses dieses Produktes gef hrliche Spannungen die nicht isoliert sind und die einen elektrischen Schock verursachen k nnen herrschen Achtung Lesen der Anleitungen Bevor Sie das Ger t zum ersten Mal verwenden sollten Sie alle Sicherheits und Bedienungsanleitungen genau durchlesen und verstehen Aufbewahren der Anleitungen Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie aufbewahren damit Sie im Bedarfsfall darauf zur ckgreifen k nnen Befolgen der Warnhinweise Befolgen Sie alle Warnhinweise und Anleitungen auf dem Ger t oder in der Benutzerdokumentation Keine Zusatzgerate Verwenden Sie keine Werkzeuge oder Zusatzger te die nicht ausdr cklich vom Hersteller empfohlen wurden da diese eine Gefahrenquelle darstellen k nnen Instrucciones de seguridad Espanol Este s mbolo se utiliza para advertir al usuario sobre instrucciones importantes de operaci n y mantenimiento o cambio
37. sed with the unit to ensure compliance with FCC emissions limits Quick Start Guide SW VGaArs Ars Series Install and operate the SW VGArs Ars Series switchers as follows Step 1 Turn all of the equipment off and disconnect it from the power source Step 2 Mount the switcher in a rack or furniture or place it on a desktop Step 3 2 e Video Input Audio Input Connect up to six video input cables Condor depending on the switcher model Ars models only Connect up to six audio e input cables depending on the switcher model Step 4 OUTPUT Connect the video output cable Step 5 Ars models coat Sa Ae AEN Connect the sleeve only Cable the ca SS 3 to ground audio output See caution i Gs Connecting the connector for Unbalanced Output sleeve to a negative stereo or mono terminal will balanced or Ring damage the audio output circuits LnNdino Sleeve s unbalanced at audio output Balanced Output Step 6 REMOTE Connect an RS 232 OR a contact closure controller Wire the connector as shown Coa in the table at right Contact PIN RS 232 Closure Function Step 7 1 In 1 Input 1 TX Transmit dat
38. the warranty period attributable directly to faulty workmanship and or materials Extron Electronics will at its option repair or replace said products or components to whatever extent it shall deem necessary to restore said product to proper operating condition provided that it is returned within the warranty period with proof of purchase and description of malfunction to USA Canada South America and Central America Europe Africa and the Middle East Extron Electronics Europe Extron Electronics Beeldschermweg 6C 1001 East Ball Road 3821 AH Amersfoort Anaheim CA 92805 USA The Netherlands Asia Japan Extron Electronics Asia Extron Electronics Japan 135 Joo Seng Road 04 01 Kyodo Building PM Industrial Bldg 16 Ichibancho Singapore 368363 Chiyoda ku Tokyo 102 0082 Japan This Limited Warranty does not apply if the fault has been caused by misuse improper handling care electrical or mechanical abuse abnormal operating conditions or non Extron authorized modification to the product If it has been determined that the product is defective please call Extron and ask for an Applications Engineer at 714 491 1500 USA 31 33 453 4040 Europe 65 6383 4400 Asia or 81 3 3511 7655 Japan to receive an RA Return Authorization number This will begin the repair process as quickly as possible Units must be returned insured with shipping charges prepaid If not insured you assume the risk of loss or damage
39. tible with the VSW I AAP REAR PANEL Revision label Board Version EXTRON 20 1118 02 A ER nnnnnnnn nnnn 49113 ER number and final digit of part number may change Figure 2 9 Board version and location of jumpers Set the jumpers for the switcher See Configuring the switcher on the next page Set the cover in place and resinstall the screws and connector nuts removed in step 2 SW VGArs Ars Series Switchers Installation 2 11 a 1 n ia di pep 1 Se gE E b Installation cont d Identifying the Board Version and Setting the SW VGA Ars Jumpers If you plan to use the switcher with VSW I AAP remote controls you must configure the switcher It is more convenient to do this before installing tt in a rack or furniture and making connections Using the SW VGA Ars switcher with VSW I AAP control panels requires you to set internal jumpers in the switcher When you open the switcher you can also check the circuit board installed in the switcher to ensure that it is compatible with the VSW I AAP control panels NOTE On the VSW I AAP remote control ensure that jumper J6 is installed Refer to the VSW I AAP manual for details 1 If applicable disconnect all power to the switcher and any attached devices 2 Remove the eight screws from the switcher three on each side of the switcher and two on top figure 2 8 Remove the two connector nuts from the Remot
40. ting brackets 70 077 02 Furniture mount the switcher as follows sf RSU 129 1U Universal Rack Shelf s nn 1 Attach the mounting brackets to the switcher with the Faceplate provided machine screws figure 2 2 o 8 y Front false faceplate uses 2 Ge Through Desk Kit Under Desk Kit Figure 2 2 Under surface or through surface mounting For through surface mounting cut the proper sized hole in the mounting surface For through surface mounting hold the switcher with the attached brackets against the underside of the table or other furniture Mark the location of the screw holes of the bracket on the mounting surface For through surface mounting drill four 3 32 2 mm diameter pilot holes 1 4 6 3 mm deep in the mounting surface at the marked screw locations For through surface mounting insert four 8 wood screws through the bracket and into the four pilot holes Tighten all four screws to secure the switcher in place For under surface mounting insert 8 wood screws into the four pilot holes Tighten each screw into the mounting surface until just less than 1 4 of the screw head protrudes For under surface mounting align the mounting screws with the slots in the brackets and place the switcher against the surface with the screws through the bracket slots For under surface mounting slide the switcher slightly forward or back then tighten all four scre
41. to the switcher using existing audio cables see figure 2 5 A stereo audio connector consists of a tip ring and sleeve The ring tip and sleeve wires are also shown on the audio output captive screw audio connector diagram figure 2 6 Tip L Sleeve GND TT l mmm Ring R N Tip L n Sleeve GND Figure 2 5 3 5 mm stereo audio plug Signal output connection All models Output connector Connect the monitor to this female 15 pin HD connector Audio SW VGA Ars models only 5 Audio output connector Insert a 3 5 mm 5 pole one piece captive screw audio connector into this connector Wire the connector as shown in figure 2 6 CAUTION Connect the sleeve to ground Gnd Connecting the sleeve to a negative terminal will damage the audio output circuits Tip 6 3 Tip OL at NO GROUND HERE 6 3 Ring Coos 6 4 Sleeve s HEIs 3 m 1 gt per OL 3 Tip 5 QL g NO GROUND HERE XS s Ring Ds QI 3 he 16 5 mm MAX Unbalanced Balanced Do not tin the wires Stereo Output Stereo Output Figure 2 6 Captive screw connector for wiring audio output 2 8 SW VGArs Ars Series Switchers Installation See the revision label the board figure 2 9 which list the board s part number Use this information to check compatibility with the VSW I AAP s NOTE If the board s part number is not 20 1182 0n this SW VGA Ars is not compa
42. tor has the pin assignments shown in figure 4 1 For RS 232 and IR control use a control cable with only pins 2 3 and 5 connected To accomplish this either cut the wires to the other pins in hard shelled connectors or remove the unneeded pins from molded plugs For contact closure use a control cable with pins 2 and 3 NOT connected To accomplish this either cut the wires to these pins in hard shelled connectors or remove these pins from molded plugs Simple Instruction Set Control Host to switcher communications SIS commands consist of one or more characters per field No special characters are required to begin or end a command character sequence When a command is valid the switcher executes the command and sends a response to the host device All responses from the switcher to the host end with a carriage return and a line feed CR LF 41 which signals the end of the response character string A string is one or more characters SW VGArs Ars Series Switchers Remote Control Audio mute status Read audio mute x2 No signal is present on inputs 4 and 6 starting from input 1 n is the maximum number of Select input Xi video only audio breakaway Each X2 response is the signal status of an input Select input Xi video and audio Select input xi audio only audio breakaway The input signal is present on inputs 1 2 3 and 5 inputs for this model Xtl s signal status Video mute on
43. varies with the switcher model These input connectors are also compatible with Extron VSW I AAP VGA video and audio input modules with the Show Me control button Refer to the VSW I AAP user s manual for details SW VGArs Ars Series Switchers Installation 2 7 Installation cont d Rear Panel Features and Connections All connectors are on the rear panel Depending on the model of the switcher the number of connectors on the rear panel varies Figure 2 3 shows the rear panels of the SW VGArs switchers Figure 2 4 shows the rear panels of the S W VGA Ars switchers REMOTE SW2 VGArs 0 0 OUTPUT ee 8 HEMOTE SWA VGArs 0 0 OUTPUT ee DIE SW6 VGArs 65 o amp e E JE e oie e 5 OHz Figure 2 3 Rear panel SW VGArs switchers no audio input or output connectors Power connection 1 AC power connector Plug a standard IEC power cord into this connector to connect the switcher to a 100 to 240 VAC 50 Hz or 60 Hz power source 2 6 SW VGArs Ars Series Switchers Installation Meg The length of exposed wires is critical The ideal length is 3 16 5 mm e Ifthe stripped section of wire is longer than 3 16 the exposed wires may touch each other causing a short circuit between them e Ifthe stripped section of wire is shorter than 3 16 wires can be easily pulled out even if tightly fastened by the captive screws Remote connection 6 Remote RS
44. ws to secure the switcher in place SW VGArs Ars Series Switchers Installation 2 5 2 4 40 x 3 16 Screws NOTE Using screws longer than 3 16 will damage the unit and void the warranty Use 2 mounting holes on opposite corners Figure 2 1 Rack mounting the switcher If rubber feet were previously installed on the bottom of the switcher remove them Mount the SW VGArs Ars Switcher on the rack shelf using two 4 40 x 3 16 screws in opposite diagonal corners to secure the switcher to the shelf figure 2 1 Attach a blank panel or other unit s to the rack shelf Insert the shelf into the rack aligning the holes in the shelf with those of the rack Secure the shelf to the rack using the supplied machine screws This shelf can be mounted in the front or in the rear of the rack SW VGArs Ars Series Switchers Installation Screws 000 0 em 6 Ec OUTPUT OUTPUT P ose n 6 6 REMOTE SWA VGA Ars oe EH ir 0 60Hz 5 02 o VGA Ars B meii T eE e Figure 2 4 Rear panel SW VGA Ars switchers with audio input and output connectors Signal input connections All models Computer input connectors Connect the computer input VGA SVGA XGA SXGA or UXGA to one of these female 15 pin HD connectors The number of available inputs
Download Pdf Manuals
Related Search