Acer AL1715M (White) 17" LCD Monitor
Contents
1. 5 Connecting the AC Power 5 Connecting the Audio Cable For AL1715 m and AL1715 bm 6 Power Management System 6 Chapter 2 Display Controls 7 General Instructions 7 Front Panel Control 8 How To Adjust A Setting 9 Adjusting The Picture 9 Chapter 3 Technical Information 11 Specifications 11 Standard Timing Table2. 13 Troubleshooting 15 2 Preface This manual is designed to assist users in setting up and using the LCD Monitor Information in this document has been carefully checked for accuracy however no guarantee is given to the correctness of the contents The information in this document is subject to change without notice This document contains proprietary information protected by copyright All rights are reserved No part of this manual may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer FCC Statement Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the inter
3. Power Indicator Green Power On mode Orange off mode MENU ENTER Activate OSD menu when OSD is OFF or activate de activate adjustment function when OSD is ON or Exit OSD menu when in Volume Adjust OSD status lt Volume Activates the volume control when the OSD is OFF only for Audio model or navigate through adjustment icons when OSD is ON or adjust a function when function is activated gt Volume Activates the volume control when the OSD is OFF only for Audio model or navigate through adjustment icons when OSD is ON or adjust a function when function is activated Auto Adjust button Exit 1 When OSD menu is in active status this button will act as EXIT KEY EXIT OSD menu 2 When OSD menu is in off status press this button for 2 seconds to activate the Auto Adjustment function The Auto Adjustment function is used to set the HPos VPos Clock and Focus NOTES Do not install the monitor in a location near heat sources such as radiators or air ducts or in a place subject to direct sunlight or excessive dust or mechanical vibration or shock Save the original shipping carton and packing materials as they will come in handy if you ever have to ship your monitor For maximum protection repackage your monitor as it was originally packed at the factory To keep the monitor looking new periodically clean it with a soft cloth Stubborn stains may be removed with a cloth lightly dampened
4. 1800 1280 112 96 312 135 00 75Hz 75 00 1000 960 3 1 36 64 1688 1280 112 48 248 108 1280x1024VESA 1024 60Hz 60 1066 1024 3 1 38 80 1688 1280 144 16 248 135 1280x1024VESA 1024 75Hz 75 1066 1024 3 1 38 Note Mode 640x350 640x400 and 720x400 will locate on middle position but cannot be expanded to full screen on vertical direction 15 Troubleshooting This LCD Monitor has pre adjusted using factory standard VGA timings Due to the output timing differences among various VGA cards in the market users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected Attention This LCD Monitor Supports Multiple VGA Modes Refer to the Standard Timing Table for a listing of modes supported by this LCD Monitor PROBLEM Picture is unclear and unstable The picture is unclear and unstable please perform the following steps 1 Enter PC to Shut Down Windows status while you re in MS Windows environment except Windows XP In Windows XP open the specific application where the problems appear 2 Check the screen to see if there s any black vertical stripes appear If there are take advantage of the Clock function in OSD menu and adjust by increment or decrement numbers until those bars disappear 3 Move to Phase function in OSD menu again and adjust the monitor screen to its most clear display 4 Click No on
5. 1 Table of Contents Preface 2 FCC Statement Warning 2 Canadian DOC Notice 2 Important Safety Instructions 3 Chapter 1 Installation 4 Unpacking 4 Connecting the LCD Monitor and Base 4 Viewing Angle Adjustment 4 Detaching LCD Monitor from Its Stand 5 Interface for Arm Applications 5 Connecting the Display
6. 879 1056 800 128 40 88 40 VESA 600 60Hz 60 317 628 600 4 1 23 800x600 48 077 1040 800 120 56 64 50 VESA 600 72Hz 72 188 666 600 6 37 23 14 TIMING FH KHZ FV HZ SYNC POLARITY TOTAL DOT LINE ACTIVE DOT LINE SYNC WIDTH DOT LINE FRONT PORCH DOT LINE BACK PORCH DOT LINE PIXEL FOREQ MHZ 800x600 46 875 1056 800 80 16 160 49 5 VESA 600 75Hz 75 625 600 3 1 21 1024x768 48 363 1344 1024 136 24 160 65 XGA 60 004 806 768 6 3 29 1024x768 53 964 1328 1024 176 16 112 71 664 COMPAQ XGA 66 132 816 768 4 8 36 1024x768 56 476 1328 1024 136 24 144 75 VESA 768 70Hz 70 069 806 768 6 3 29 1024x768 60 023 1312 1024 96 16 176 78 75 VESA 768 75Hz 75 029 800 768 3 1 28 1024x768 60 24 1328 1024 96 32 176 80 APPLE MAC 768 75 02 803 768 3 3 29 1152x864 54 054 1480 1152 96 40 192 80 60Hz 59 270 912 864 3 13 32 1152x864 63 851 1480 1152 96 32 200 94 499 70Hz 70 012 912 864 3 1 44 1152x864 67 50 1600 1152 128 64 256 108 00 75Hz 75 00 900 864 2 2 32 1280x960 60 00 1800 1280 112 96 312 108 00 60Hz 60 00 1000 960 3 1 36 1280x960 70 00 1800 1280 112 96 312 126 00 70Hz 70 00 1000 960 3 1 36 1280x960 75 00
7. with a mild detergent solution Never use strong solvents such as thinner benzene or abrasive cleaners since these will damage the cabinet As a safety precaution always unplug the monitor before cleaning it 9 How To Adjust A Setting 1 Press the MENU button to activate the OSD window 2 Press lt or gt to select the desired function 3 Press the MENU button to select the function that you want to adjust 4 Press lt or gt to change the settings of the current function 5 To exit and save select the exit function If you want to adjust any other function repeat steps 2 4 Adjusting The Picture The descriptions for function control LEDS Main Menu Icon Sub Menu Icon Sub Menu Item Description Contrast Adjusts the contrast between the foreground and background of the screen image Brightness Adjusts the background brightness of the screen image Focus Adjusts picture Focus Clock Adjusts picture Clock H Position Adjust picture Focus V Position Adjust picture Clock N A Warm Set the color temperature to warm white N A Cool Set the color temperature to cool white User Red User Green User Blue Adjusts Red Green Blue intensity 10 N A English N A N A Deutsch N A Fran ais N A Espa ol N A Italiano N A N A Multi language selection H Position Adjust the horizontal position of the OSD V Position Adjust
8. Shut Down Windows and back to the normal PC operating environment PROBLEM There is no picture on LCD Monitor If there s no picture on the LCD Monitor please perform the following steps 1 Make sure the power indicator on the LCD Monitor is ON all connections are secured and the system is running on the correct timing Refer to Chapter 3 for information on timing 2 Turn off the LCD Monitor and then turn it back on again If there is still no picture press the Adjustment Control button several times 3 If step 2 doesn t work connect your PC system to another external CRT If your PC system Functions properly with a CRT Monitor but it does not function with the LCD Monitor the output timing of the VGA card may be out of the LCD s synchronous range Please change to an alternative mode listed in the Standard Timing Table or replace the VGA card and then repeat steps 1 and 2 PROBLEM There is no picture on LCD Monitor If you have chosen an output timing that is outside of the LCD Monitor s synchronous range Horizontal 24 80 KHz and Vertical 49 75 Hz the OSD will display a Out of Range message Choose a mode that is supported by your LCD Monitor Also if the signal cable is not connected to LCD monitor at all or properly the monitor screen will display a message No Input Signal
9. e settings in memory 12 Power Management Mode Power Consumption AC Input LED Color On 60W maximum 240 VAC Green Off 3W maximum 240 VAC Yellow Soft switch off 3W maximum 240 VAC Dark Disconnected 3W maximum 240 VAC Yellow Standby Suspend Off Dark DC Power off Meeting VESA DPMS requirements measured from AC Input end of AC power cord Sync Input Signal Separate TTL compatible horizontal and vertical synchronization Polarity Positive and negative Plug amp Play Supports VESA DDC2B functions External Connection Power Input AC input AC socket Video Cable 1 8M with 15 pin D sub connector Audio Cable 1 8M with Stereo Jack Environment Operating Condition Storage Condition Temperature Relative Humidity Temperature Relative Humidity 5 C to 40 C 41 F to 104 F 20 to 80 20 C to 60 C 4 F to140 F 5 to 85 Power Supply AC Input Input Voltage Single phase 100 240VAC 50 60 Hz Input Current 1 2 A maximum Size and Weight Dimensions 377 W x 393 H x 159 8 D mm Net Weight 5 0 5 kg Gross Weight 7 0 5 kg Pin Assignment Signal PIN Description PIN Description PIN Description 1 5 6 10 11 15 1 2 3 4 5 Red Green Blue Digital GND Digital GND 6 7 8 9 10 Red Rtn Green Rtn Blue Rtn 5V Hot Plug Detect 11 12 13 14 15 NC SDA H Sync V Sync SCL 13 Standard Timing Table If the selected timi
10. ference by one or more of the following measures Reposition or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced monitor technician for help Warning Use only shielded signal cables to connect I O devices to this equipment You are cautioned that changes or modifications not expressly approved by the party responsible for comliance could void your authority to operate the equipment Canadian DOC Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe B repecte toutes les exigences du R glement sur le mat riel brouilleur du Canada 3 Important Safety Instructions Please read the following instructions carefully This manual should be retained for future use 1 To clean LCD Monitor screen Power off LCD Monitor and unplug the AC Cord Spray a non solvent cleaning solution onto a rag Gently clean the screen with dampened rag 2 Do not place the LCD Monitor near a window Exposing the monitor to rain water moisture or sunlight can severely damage it 3 Do not apply pressure to the LCD screen Excess pressure may cause permanent damage to the display 4 Do not remove the cover or attempt to service this unit by yourself Ser
11. g 1 6 2 Connect the power cord to an AC power source Figure 1 6 6 Connecting the Audio Cable For AL1715 m and AL1715 bm 1 Connect the audio cable to the LINE OUT jack on your PC s audio card or to the front panel s AUDIO OUT jack of your CD ROM drive See Fig 1 7 2 Connect the other end of the audio cable to the LCD Monitor s LINE IN jack Figure 1 7 Power Management System This LCD Monitor complies with the VESA DPMS version 1 0 Power Management guidelines The VESA DPMS provides four power saving modes through detecting a horizontal or vertical sync signal When the LCD Monitor is in power saving mode the monitor screen will be blank and the power LED indicator will light yellow 7 Chapter 2 Display Controls General Instructions Press the power button to turn the monitor on or off The other control buttons are located at front panel of the monitor See Figure 2 1 By changing these settings the picture can be adjusted to your personal preferences The power cord should be connected Connect the video cable from the monitor to the video card Press the power button to turn on the monitor position The power indicator will light up Figure 2 1 External Controls 1 Auto Adjust Key Exit 4 MENU ENTER 2 lt Volume 5 LED 3 gt Volume 6 Power Key 8 Front Panel Control Power Button Press this button to turn the monitor ON or OFF And display the monitor s state
12. ng is NOT included in table below this LCD monitor will use the most suitable available timing TIMING FH KHZ FV HZ SYNC POLARITY TOTAL DOT LINE ACTIVE DOT LINE SYNC WIDTH DOT LINE FRONT PORCH DOT LINE BACK PORCH DOT LINE PIXEL FOREQ MHZ 640x350 31 469 800 640 96 16 48 25 175 VGA 350 70 087 449 350 2 37 60 640x400 24 83 848 640 64 64 80 21 05 NEC PC9801 56 42 440 400 8 7 25 640x400 31 469 800 640 96 16 48 25 175 VGA GRAPH 70 087 449 400 2 12 35 640x400 31 5 800 640 64 16 80 25 197 NEC PC9821 70 15 449 400 2 13 34 640X480 31 469 800 640 96 16 48 25 175 VESA PAL 50 030 629 480 2 62 85 640x480 31 469 800 640 96 16 48 25 175 VGA 480 59 94 525 480 2 10 33 640x480 35 00 864 640 64 64 96 30 24 APPLE MAC 480 66 67 525 480 3 3 39 640x480 37 861 832 640 40 16 120 31 5 VESA 480 72Hz 72 809 520 480 3 1 20 640x480 37 5 840 640 64 16 120 31 5 VESA 480 75Hz 75 500 480 3 1 16 720x400 31 469 900 720 108 18 54 28 322 VGA 400 TEXT 70 087 449 400 2 12 35 832x624 APPLE 49 725 1152 832 64 32 224 57 2832 MAC 800 74 55 667 624 3 1 39 800x600 35 156 1024 800 72 24 128 36 SVGA 56 25 625 600 2 1 22 800x600 37
13. r dealer immediately Connecting the LCD Monitor and Base When you open the box to take the base and put on the desk first Then connect the LCD Monitor and base please See fig 1 1 Figure 1 1 Viewing Angle Adjustment The LCD Monitor is designed to allow users to have a comfortable viewing angle The viewing angle can be adjusted from 5 to 15 See fig 1 2 Figure 1 2 Warning Do not force the LCD Monitor over its maximum viewing angle settings as stated above Attempting this will result in damaging the Monitor and Monitor stand 5 Detaching LCD Monitor from Its Stand Unscrew screws the swivel base support column and pull down the hinge to release Figure 1 3 Interface for Arm Applications Before installing to mounting device please refer to Fig 1 3 The rear of this LCD display has four integrated 4 mm 0 7 pitches threaded nuts as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1 4 These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard paragraphs 2 1 and 2 1 3 version 1 dated 13 November 1997 Figure 1 4 Connecting the Display 1 Power off your computer 2 Connect one end of the signal cable to the LCD Monitor s VGA port See Fig 1 5 3 Connect the other end of the signal cable to the VGA port on your PC 4 Make sure connections are secure Figure 1 5 Connecting the AC Power 1 Connect the power cord to the LCD Monitor See Fi
14. the vertical position of the OSD OSD Timeout Adjust the OSD timeout N A Auto Config Auto Adjust the H V Position Focus and Clock of picture N A Information Show the resolution H V frequency and input port of current iput timing N A Reset Clear each old status of Auto configuration and set the color temperature to Cool N A Exit Save user adjustment and OSD disappear 11 Chapter 3 Technical Information Specifications LCD Panel Size 17 43 cm Display Type Active matrix color TFT LCD Resolution 1280 x 1024 Display Dot 1280 x RGB x 1024 Display Area mm H x V 337 92 x 270 336 Display Color 262K Brightness 250 cd m2 typical 200 cd m2 minimum Contrast Ratio 430 1 typical Response Time Ta 25 C Tr Tf 20ms Lamp Voltage 700 Vrms typical Lamp Current 6 5 mA rms typical Viewing Angle Vertical 65 65 Horizontal 80 80 Display Colors 16 7M with FRC or Dithering Video Input Signal Input Impedance Polarity Amplitude Multi mode Supported Analogue RGB 0 7Vp p 75 Ohm 2 Positive Negative 0 0 7 0 05 Vp Horizontal Frequency 24 80 KHz Vertical Frequency 49 75 Hz Control Power switch On Off switch with LED indicator Audio AL1715 m AL1715 bm Input 500mVrms Output 1W 1W OSD Brightness Contrast Horizontal Position Vertical Position Phase Clock Display Mode Setup Digital Digital Digital Digital Digital Digital Use EEPROM to sav
15. vicing of any nature should be performed by an authorized technician 5 Store LCD Monitor in a room with a room temperature of 20 60 C or 4 140 F Storing the LCD Monitor outside this range could result in permanent damage 6 If any of the following occurs immediately unplug your monitor and call an authorized technician Monitor to PC signal cable is frayed or damaged Liquid spilled into LCD Monitor or the monitor has been exposed to rain LCD Monitor or the case is damaged 7 Only use the supplied main lead to connect the monitor For a nominal current up to 6A and a device weight above 3 kg a line not lighter than H05VV F 3G 0 75 mm2 must be used 4 Chapter 1 Installation Unpacking Before unpacking the LCD Monitor prepare a suitable workspace for your Monitor and computer You need a stable and clean surface near a wall power outlet Make sure that LCD Monitor has enough space around it for sufficient airflow Though the LCD Monitor uses very little power some ventilation is needed to ensure that the Monitor does not become too hot AL1715 AL1715 b AL1715 m AL1715 bm AUDIO No No Yes Yes After you unpack the LCD Monitor make sure that the following items were included in the box LCD Monitor User s Manual 1 8M Monitor to PC VGA Cable 1 8M Stereo Jack Audio Cable for AL1715 m and AL1715 bm 1 8M Power Cord Base If you find that any of these items is missing or appears damaged contact you
Download Pdf Manuals
Related Search