Toshiba 13A21 13" TV
Contents
1. SPECIFICATIONS Model 13A21 19A21 AC Power Input 120V 60Hz AC Power Consumption 54 Watts 73 Watts Picture Tube Type 13 335mm diagonal Type 19 480mm diagonal Audio Power Output Rating 1 0 Watts 1 5 Watts Speaker 3 inches 76mm Full Range 8 ohm x 1 Tuner Type 181 Channel Quartz PLL Frequency Synthesized Remote Control Infrared Direct Access 2 x AAA batteries supplied VHF 2 13 UHF CATV Receiving Channels 37 65 AA FFF 66 125 GGG 125 Antenna Input Impedance 75 Ohm VHF UHF Coaxial Input Video 1 0 Vp p 75 ohm Input Audio 300 mV 47k ohm Width 14 1 4 inches 362mm Width 19 3 16 inches 488mm Height 12 5 8 inches 320 5mm Height 16 3 8 inches 416mm Depth 14 3 16 inches 360mm Depth 18 5 16 inches 465mm Dimensions Weight 20 9 Ibs 9 5 kg 38 6 Ibs 17 5 kg ACCESSORY Remote Control with two size AAA batteries TOSHIBA AMERICA CONSUMER PRODUCTS INC Head Office 82 Totowa Road Wayne NJ 07470 National Service Division 1420B Toshiba Drive Lebanon TN 37087 TOSHIBA HAWAII INC Head Office 327 Kamakee Street Honolulu HI 96814 3J81301B U 01 06 ANTENNA CATV CONNECTIONS Printed in Thailand OWNER S MANUAL COLOR TELEVISION TOSHIBA 13A21 19A21 CAUTION Changes or modifications not expressly approved by the party responsible for compli ance with the F2. TV MA C TV Y all children TV PG parental guidance TV Y7 7 years old and above TV 14 14 years old and above TV G _ childrens program TV MA 17 years old and above When you select TV Y7 TV PG TV 14 or TV MA press the CALL button to explain the rating Press the SET or button to select the desired rating you want Press the ENTER button to select the setting ON or OFF MOVIE RATING SET lt gt SET OFF lt gt G lt gt PG lt gt PG 13 lt gt R lt gt NC 17 lt gt X G all ages R under 17 years old parental PG parental guidance guidance suggested PG 13 parental guidance less than 13 NC 17 17 years old and above years old X adult only Press the MENU button until the MENU screen is cleared NOTES If you want to change password follow steps 1 and 2 and select CHANGE PASSWORD option then enter your new password e The V Chip function is activated only on programs and tapes that have the rating signal Once you block a program using the V Chip function the blocked program cannot be watched based on the content of the show When the program starts the INPUT PASSWORD will appear on the screen When you want to release the V Chip temporarily enter the password If you change the channel or turn off the TV while the V Chip function was temporarily released the original setting will be resumed If you return to the channel you were watching you must re enter your password to tempora
3. of BARS AND THE NUMBER on the screen The same is true for decreasing the level Set the TV CABLE menu option to the appropriate position When shipped from the factory this menu option is in the CATV setting See To Memorize Channels TV VHF UHF channels CABLE CABLE TV channels CH CHANNEL and buttons Press and release the CH CHANNEL or button The channel automatically stops at the next channel set into memory Press and hold the button down to change channels more quickly For proper operation before selecting channels they should be set into the TV s memory See To Memorize Channels DIRECT CHANNEL SELECTION buttons 0 9 Press these buttons to select a channel The channel number will appear on the upper right corner of the TV screen If an invalid channel number is selected the display will revert to the previous channel TV MODE DIRECT CHANNEL SELECTION When the TV CABLE menu option is in the TV position all channels can be instantly selected by using two buttons For example to select channel 2 press 0 then 2 If you press only 2 channel selection will be delayed for a few seconds For channels 10 and above press the 2 digits in order CABLE mode direct channel selection When the TV CABLE menu option is in the CABLE position channels can be selected as follows 1 9 Press 0 twice then 1 9 as needed Example to select channel 2 press 002 10 12 Press 0 t
4. station e Check sound adjustments VOLUME and MUTE Check for sources of possible interference Poor sound or No sound e Station or CATV experiencing problems tune to another station e Make sure channels are set into memory e Check antenna or CATV connections adjust antenna e Check for sources of possible interference e Check picture control adjustments Station or CATV experiencing problems tune to another station e Make sure channels are set into memory Station is weak adjust antenna to receive desired station Check for sources of possible interference Poor picture or No picture Poor reception on some channels Station or CATV experiencing problems tune to another station e Make sure channels are set into memory e Check picture control adjustments Check antenna or CATV connections reorient antenna e Check for sources of possible interference Poor color or no color Station or CATV experiencing problems tune to another station e Make sure channels are set into memory CATV company is scrambling signal e Adjust antenna e Check all CATV connections Set TV CABLE menu option to the CABLE mode Station or CATV system problems try another station e Check antenna connections reorient antenna e Check for sources of possible interference Picture wobbles or drifts No CATV reception Horizontal or diagonal bars on screen e Make sure TV CABLE men
5. to return to normal TV viewing a The chart below is typical of many cable system channel allocations CATV CHART Number on this TV 14 15 16 17 18 19 20 21 22 Corresponding CATV channel A B ej D E F G H I 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 J K L M N O P Q R S T U V W AA BB CC DD 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 EE FF GG HH II JJ KK LL MM NN OO PP QQ RR SS TT UU WV 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 WW _ AAA BBB CCC DDD EEE FFF GGG HHH lll JJJ KKK LLL MMMNNN OOO PPP QQQ 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 RRR SSS TTT UUU VVV WWW XXX YYY ZZZ 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 A 5 A 4 A 3 A 2 A 1 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 01 1143 114 115 116 117 118 119 120 121 122 123 124 125 5A NOTE Contact your cable company to determine the type of cable system used in your area AUTOMATIC CHANNEL MEMORY Press the MENU button Bee ZEN PICTURE E LANGUAGE E V CHIP SET Press the SET or button until the indicator next to CH SET begins to flash then press the ENTER button ENTER MENU Press the SET or button until the indicator next to AUTO CH MEMORY begins to flash then press the ENTER button The TV will begin memorizing all the channels available in your area Channel numbers will rema
6. when the signal is received again If the channels are changed the Captions will be delayed approximately 10 seconds The Captions will appear in places on the screen where they will least interfere with the picture usually on the bottom of the screen News programs will usually show three line Closed Captions which scroll onto the screen Most other shows provide two or three lined Captions placed near the character who is speaking so the viewer can follow the dialogue Words in italics or underlined describe titles words in foreign languages or words requiring emphasis Words that are sung usually appear enclosed by musical notes For television programs broadcasting with Closed Captions look in your TV guide for the Closed Captions symbol CC e When activating the Closed Captioned Decoder there will be a short delay before the Closed Captioned text appears on the screen e Closed Captioned text is only displayed in locations where it is available e If no caption signal is received no captions will appear but the television will remain in the Caption Mode e Misspellings or unusual characters may occasionally appear during Closed Captioning This is normal with Closed Captioning especially with live programs This is because during live programs captions are also entered live These transmissions do not allow time for editing e When Captions are being displayed on screen displays such as volume and mute may not be seen or may inte
7. CC Rules could void the user s authority to operate this equipment ATTENTION If you purchase a universal remote control from your local retailer please contact the remote manufacturer for the required programming code TV CATV MODE SELECTION When shipped from the factory the TV CABLE menu option is set to the CABLE Cable Television mode If not using CABLE set this menu option to TV mode FEATURES Quartz PLL Frequency Synthesized Tuning System Electronically locks in and memorizes available channels for perfect reception 181 Channel Tuner The tuning system is capable of receiving all 68 VHF UHF standard broadcast channels that are available in your area When operating on a cable system it can tune to the standard VHF channel frequencies plus up to 113 cable channel frequencies The actual number of channels received depends upon channel reception in your area or your cable system On Screen 3 Language Display This TV can display the on screen language in English Spanish or French Picture Adjustments Using The Remote Control The On Screen display allows precise remote control adjustment of BRIGHTNESS COLOR CONTRAST SHARPNESS and TINT Sleep Timer Operable from the remote control this TV can be programmed up to 120 minutes to turn off automatically Memory Back Up This system prevents loss of memorized channel selections in case a power interruption to the TV should occur Closed Captioned Decoder Displa
8. NCE TO RAIN OR MOISTURE TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT Limited United States Warranty Toshiba America Consumer Products Inc TACP and Toshiba Hawaii Inc THI make the following limited warranties These limited warranties extend to the original con sumer purchaser or any person receiving this set as a gift from the original consumer pur chaser and to no other purchaser or trans feree Limited One 1 Year Warranty TACP and THI warrant this product and its parts against defects in materials or work manship for a period of one 1 year after the date of original retail purchase During this period TACP and THI will repair or replace a defective part at their option with a new or refurbished part without charge to you Au thorized TACP THI service station personnel will come to your home when warranty serv ice is required Depending on the type of re pair required the service will either be per formed in your home or the set will be taken to the authorized TACP THI service station for repair and returned to your home at no cost to you Limited Two 2 Year Warranty of Picture Tube TACP and THI further warrant the picture tube in this product against defects in materials or workmanship for a period of two 2 years after the date of original retail purchase REMO
9. TE CONTROL During this period TACP and THI will repair or replace a defective picture tube at their op tion with a new or refurbished picture tube without charge to you except that if a defec tive picture tube is replaced after one 1 year from the date of original retail purchase you pay labor charges involved in the replace ment Rental units The warranty for rental units begins with the first rental of thirty 30 days from the date of shipment to the rental firm whichever comes first Commercial units Products sold and used for commercial use have a limited ninety 90 day warranty for all parts labor and picture tube Owner s manual and registration card You should read this owner s manual thor oughly before operating this product You should complete and mail the enclosed registration card within ten days after you or the person who has given you this product as a gift pur chased this product This is one way to en able TACP THI to provide you with better cus tomer service and improved products Fail ure to return the registration card will not af fect your rights under this warranty The above warranties are subject to the fol lowing conditions e You must retain your bill of sale or provide other proof of purchase e All warranty servicing of this product must be made by an Authorized TACP THI Service Station These warranties are effective only if the prod uct is purchased and operated in
10. ange to a higher numbered channel set into memory Press the button to change to a lower numbered channel set into memory 13 ENTER Button Press to enter or select information for On Screen operations CAP TEXT Button Press this button to switch between normal TV and the two Closed Caption modes captions and 1 2 of full screen text Closed Captioning will display text on screen for hearing impaired viewers 15 1 2 Button Switches between Channel 1 and Channel 2 in the Closed Caption mode LOCATION OF CONTROLS 19A21 13A21 123456 7 PHONE Earphone Jack Plug an earphone or monaural headphones with an 1 8 miniplug into this jack for private listening POWER indicator Lights up when the power is turned on Remote Sensor Signals from the Remote Control unit are received here POWER Button Press to turn the TV on or off VOLUME A F Buttons Press to raise or lower the level of the sound MENU Buttons Press both VOLUME A F Buttons at the same time to display the On Screen menu functions SET Buttons Press to select the desired setting during On Screen operations 23456 7 6 CHANNEL A F Buttons Press to select a higher or lower numbered channel set into memory ENTER Button Press to enter or select information for On Screen operations RESET Button Press while in the On Screen menu mode to reset the On Scr
11. ate VHF UHF Antennas Connect the 75 ohm cable from the VHF antenna and the UHF antenna twin lead to a combiner not supplied Attach the combiner to the antenna jack NOTE If your VHF antenna has a twin lead wire use the 300 75 ohm matching transformer not supplied then connect the transformer to the combiner For Subscribers to Basic Cable TV Service For basic cable service not requiring a converter This television has an extended tuning range and can tune most cable channels without using a cable company supplied converter box Some cable companies offer premium pay channels in which the signal is scrambled Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable descrambler box connect the CATV 75 ohm coaxial cable directly to the antenna jack on the back of the television For Subscribers to Scrambled Cable TV Service If you subscribe to a cable service which requires the use of a converter descrambler box connect the incoming cable to the converter descrambler box and connect the output of the box to the antenna jack on the back of the television Follow the connections shown left Set the television to the output of the converter descrambler box usually channel 3 or 4 and use the converter descrambler box to select channels For Subscribers to Unscrambled Basic Cable with Scrambled Premium Channels If you subscribe to a cable se
12. ed service station for repair and returned to your home at no cost to you If your TV requires service call toll free 1 800 631 3811 Toll Free 1 800 631 3811 In Hawaii If your TV requires service call 808 591 9281 327 Kamakee Street Honolulu HI 96814 Limitations All warranties implied by state law including the implied warranties of merchantability and fitness for a particular purpose are expressly limited to the duration of the limited warranties set forth above With the exception of any warranties im plied by state law as hereby limited the forego ing warranty is exclusive and in lieu of all other warranties guarantees agreements and simi lar obligations of manufacturer or seller with re spect to the repair or replacement of any parts In no event shall TACP or THI be liable for con sequential or incidental damages No person agent distributor dealer or company is authorized to change modify or extend the terms of these warranties in any manner what soever The time within which action must be commenced to enforce any obligation of TACP or THI arising under this warranty or under any statute or law of the United States or any state thereof is hereby limited to 90 days from the date you discover or should have discovered the defect This limitation does not apply to im plied warranties arising under state law This warranty gives you specific legal rights and you may also have other rights
13. een picture adjustments to their factory preset positions 7 AUDIO VIDEO IN Jack Audio and video signal cables from an external source can be connected here SETTING LANGUAGE This TV can display the channel number on screen displays and picture adjustments on the screen in English Spanish or French On screen language selection step 3 will automatically appear on the screen when you press the MENU button initially Select the language you prefer first then proceed with the other menu options Press the MENU button N ee H PICTURE E LANGUAGE Press the SET or button to select the LANGUAGE mode then press the ENTER button aS V CHIP SET ENTER MENU Press the SET or button until the gt indicator points to the desired language English ENGLISH LANGUAGE IDIOMA LANGUE Spanish ESPANOL or French FRANCAIS then gt ENGLISH press the ENTER button ESPANOL FRANCAIS ENTER MENU Press the MENU button again NOTE If Spanish or French is chosen the Closed Caption indicators will be in the selected language but the Closed Caption text will not be affected by the language selection TV OPERATION To turn on the TV press the POWER button The VOLUME can be adjusted to a desired level by pressing the VOL VOLUME or button The sound level will be indicated on the TV screen by GREEN BARS AND A NUMBER As the sound level increases so do the number
14. ery leakage 5 Do not try to recharge batteries not intended to be recharged they can overheat and rupture Follow battery manufacturer s directions TO USE AC POWER SOURCE Use the AC polarized line cord provided for operation on AC Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet AC Outlet NOTE Wider Hole and Blade 3 If you Polarized AC Cord Plug One blade is wider than the other 3J81301A E 3 1 Never connect the AC line cord plug to other than the specified voltage 120V 60Hz Use the attached power cord only 2 If the polarized AC cord does not fit into a non polarized AC outlet do not attempt to file or cut the blade It is the user s responsibility to have an electrician replace the obsolete outlet cause a Static discharge when touching the unit and the unit fails to function simply unplug the unit from the AC outlet wait a few minutes and plug it back in The unit should return to normal operation 1 POWER Button Press to turn the TV on Press again to turn the TV off 2 Direct Channel Selection Buttons 0 9 Allows direct access to any channel 3 CH RTN Button This button allows you to go back to the previous channel selected by just pressing the CH RTN button Press this button again to return to the channel you were watching 4 SLEEP Button To set the TV to turn off after a preset amount of time press t
15. he SLEEP button on the remote control The clock will count down 10 minutes each time the button is pressed in the order of 120 110 100 20 10 0 5 2 01 5 31 PM After the sleep time is programmed the display will disappear then reappear momentarily every ten minutes to remind you the sleep timer function is operating To confirm the sleep time setting press the SLEEP button once and the remaining time will be momentarily displayed To cancel sleep time press the SLEEP button repeatedly until the display turns to 0 5 VOL VOLUME Buttons Press the button to increase or the button to decrease the volume level 6 MENU Button Press to display the On Screen menu function 7 SET Buttons Press to select the desired setting during On Screen operations 8 RESET Button Press to reset the On Screen picture adjustments to their factory preset positions 9 TV VIDEO Button Switches between TV and external inputs 10 RECALL Button When you press this button the channel number will appear in the upper right corner of the screen Press the button again to remove display from the screen 11 MUTE Button To turn off the sound press this button once The TV will be silenced and the symbol MUTE will appear on the screen The muting feature can be released by pressing the MUTE button again or one of the VOL or buttons 12 CH CHANNEL Buttons Press the button to ch
16. hen remaining 2 digits Example to select channel 12 press 012 13 99 Press the 2 digits in order Example to select channel 36 press 36 100 125 Press the 3 digits in order Example to select channel 120 press 120 NOTE If the station being viewed stops broadcasting the TV will automatically shut off after 15 minutes 3J81301A E 4 CLOSED CAPTION WHAT IS CLOSED CAPTIONING This television has the capability to decode and display Closed Captioned television programs Closed Captioning will display text on the screen for hearing impaired viewers or it will translate and display text in another language TO VIEW CLOSED CAPTIONS Press the CAP TEXT button on the remote control to switch between normal TV and the two Closed Caption Modes Captions and 1 2 of Full Screen Text Captions This Closed Caption Mode will display text on the screen in English or another language depending on the setting of the Closed Captions 1 2 button Generally Closed Captions in English are transmitted on Captions Channel 1 and Closed Captions in other languages are transmitted on Captions Channel 2 Text The Text Closed Caption Mode will usually fill 1 2 of full screen with a programming schedule or other information After selecting a Closed Caption Mode it will stay in effect until it is changed even if the channel is changed If the Captions signal is lost due to a commercial or a break in the signal the Captions will reappear
17. in red until auto memorizing is complete E TV gt CABLE va E AUTO CH MEMORY aN E ADD DELETE ENTER MENU Press the MENU button twice to return to normal TV viewing TO ADD DELETE CHANNELS Press the MENU button AoT ZEN PICTURE E LANGUAGE E V CHIP SET Press the SET or button until the indicator next to CH SET begins to flash then press the ENTER button ENTER MENU Press the SET or button until the indicator next to ADD DELETE begins to flash then press the ENTER button E TV gt CABLE E AUTO CH MEMORY A amp Me Select the desired channels to be added or deleted using the Direct Channel Selection buttons 10 keys 0 9 the CH or button or the SET or button Nas E ADD DELETE aN ENTER MENU Press the ENTER button to select ADD or DELETE If an unmemorized channel was selected step 4 the channel indication will be red Press the ENTER button if you wish to ADD the unmemorized channel The channel indicator will change from red to green when a channel is added and the channel will be memorized If a memorized channel was selected step 4 the channel indication will be green Press the ENTER button if you wish to DELETE the channel from memory The channel indicator will change from green to red when a channel is deleted Repeat Steps 4 and 5 for each channel to be added or deleted 2 ENTER MENU 6 Press the MENU button th
18. of TV To playback from the camcorder connect e yay Ai the camcorder to the TV as shown Front of TV f f To Audio Video tf ED e AV OUT jack Q out VIDEO AUDIO not supplied not supplied 3J81301A E 5 ADJUSTING PICTURE You can adjust the settings for color sharpness contrast brightness and tint Press the MENU button Press the SET or button until the indicator next to PICTURE begins to flash then press the ENTER button Press the ENTER button repeatedly to select the item you want to adjust BRIGHTNESS gt CONTRAST gt COLOR gt TINT gt SHARPNESS Press the SET or button to adjust the setting BRIGHTNESS increase brightness decrease brightness CONTRAST increase contrast decrease contrast COLOR be brilliant color be pale color TINT be greenish color be reddish color SHARPNESS makes picture clearer makes picture softer TO RETURN TO INITIAL SETTING Press the RESET button while the picture adjusting mode appears on screen TROUBLESHOOTING GUIDE Before requesting service please refer to the following chart for the symptom and possible solution SYMPTOMS POSSIBLE SOLUTIONS e Make sure the power cord is plugged in e Try another AC outlet e Power is off check fuse or circuit breaker Unplug unit for an hour then plug it back in TV does not operate Station or CATV experiencing problems tune to another
19. ree times after adding or deleting all of the desired channels to return to normal TV viewing CONNECTION TO OTHER EQUIPMENT The exact arrangement you use to interconnect various video and audio components to the TV is dependent on the model and features of each component Check the Owner s Manual provided with each component for the location of video and audio inputs and outputs The connection diagrams in the following are offered as suggestions You may need to modify them to accommodate your particular assortment of components The diagrams are intended to show compo nent video and audio interconnections only Press the TV VIDEO selector button to select the AV mode to use the TV as a monitor Operate your VCR as usual 2 To connect the TV to a TV Game TV AV SELECTION The TV can also be used as a display device If you connect the TV to VCR camcorder or TV for many video games However due to the wide variety of different types of signal Bree you can select by pressing the TV VIDEO generated by these devices and subsequent Press the TV VIDEO button repeatedly to select the ea Welded cece y nave nor al desired mode i weet ae diagrams You ll need to consult each component s VIDEO will display on the screen for 4 seconds Owner s Manual for additional information VIDEO To Audio Video OUT Front of TV tt ie 1 To connect the TV to a VCR not steplied VCR 3 To connect the TV to a camcorder Front
20. rfere with Closed Captions Some cable systems and copy protection systems may interfere with the Closed Captioned signal e If using an indoor antenna or if TV reception is very poor the Closed Caption Decoder may not appear or may appear with strange characters or misspelled words In this case adjust the antenna for better reception or use an outdoor antenna SETTING V CHIP This TV is fitted with a V CHIP controller which provides you with channel viewing access controls and restrictions This function is to prevent your children from watching violence or sexual scenes that you may choose to exclude Press the MENU button and press the SET or button to select the V CHIP SET option then press the ENTER button Enter your password 4 digits using the Direct channel selection buttons 0 9 In the event of entering incorrect password press the RESET button Then press the ENTER button Enter the same password for confirmation then press the ENTER button Press the SET or button to select the V CHIP option Press the ENTER button to select the ON Press the SET or button to select the TV RATING or MOVIE RATING option Press the ENTER button la Ale gt Press the SET or button to select the desired rating for the applicable video or TV channel Press the ENTER button TV RATING SET lt gt SET OFF lt gt TV Y lt gt TV Y7 lt gt TV G lt gt gt TV PG lt gt TV 14 lt gt
21. rily release your V Chip function again When you watch the TV from the cable box or the VCR with the RF Modulator then you release the V Chip temporarily the V Chip setting will not be resumed until you turn off the TV The TV channel is not used in this case When changing the channel with the cable box or the VCR approximately 10 seconds will pass until the program appears 5 2 01 5 31 PM _ ae TO MEMORIZE CHANNELS This TV is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory skipping over unwanted channels Before selecting channels they must be programmed into the TV s memory In addition to normal VHF and UHF channels this TV can receive up to 113 Cable TV channels To use this TV with an antenna set the TV CABLE menu option to the TV setting When shipped from the factory this menu option is in the CABLE setting TV CABLE SELECTION Press the MENU button A M NU E CH SET WS PICTURE Press the SET or button until the indicator next to CH SET begins to flash then press the ENTER button E LANGUAGE E V CHIP SET ENTER MENU Press the SET or button until the indicator next to TV CABLE begins to flash S E TV gt CABLE A amp NA Press the ENTER button to select the TV or CABLE mode The AJ arrow indicates the selected mode BAU MEMORY E ADD DELETE o Press the MENU button twice
22. rvice in which basic cable channels are unscrambled and premium channels require the use of a converter descrambler box you may wish to use a two set signal splitter sometimes called a two set coupler and an A B switch box from the cable installer or an electronics supply store Follow the connections shown left With the switch in the B position you can directly tune any nonscrambled channels on your TV With the switch in the A position tune your TV to the output of the converter descrambler box usually channel 3 or 4 and use the box to tune scrambled channels 5 17 01 12 40 PM oe as Your responsibility In the Continental U S The lightning flash with arrowhead symbol within an CAUTION S OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock operating and maintenance servicing instructions in the literature accompanying the appliance The exclamation point within an equilateral triangle is N intended to alert the user to the presence of important CAUTION BLADE EXPOSURE WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIA
23. the U S A or Puerto Rico e Labor service charges for set installation set up adjustment of customer controls and instal lation or repair of antenna sys tems are not covered by this warranty Reception problems caused by inadequate antenna systems are your responsibility Warranties extend only to defects in materials or workmanship as limited above and do not extend to any product or parts which have been lost or discarded by you or to damage to products or parts caused by misuse accident damage caused by Acts of God such as lightning or fluctuations in electric power improper installation improper maintenance or use in violation of instruc tions furnished by us or to units which have been modified or had the serial number removed altered defaced or rendered illegible How to obtain warranty service If after following all of the operating instruc tions in this manual and checking the sec tion Troubleshooting you find that service is needed e Call the TACP toll free number 1 800 631 3811 after you find a defective product or part to find the nearest Toshiba Authorized Service Station e Please present your bill of sale or other proof to the Authorized Service Station Authorized TACP THI service station person nel will come to your home when warranty service is required Depending on the type of repair required the service will either be performed in your home or the set will be taken to the TACP THI Authoriz
24. u option is in the appropriate mode If using antenna check UHF antenna connections Batteries are weak dead or inserted incorrectly Remote is out of range move closer to TV within 15 feet Make sure Remote is aimed at sensor e Confirm there are no obstructions between the Remote and the TV Make sure the power cord is plugged in No reception above channel 13 No Remote operation e No broadcast on station tuned Sleep Timer is set e Power interrupted e TV station experiencing problems or program tuned is not closed captioned Try another channel e Check CATV connection or VHF UHF antenna reposition or rotate antenna e Press CAP TEXT button to turn on the closed caption decoder Select proper language in the menu options TV shuts off Closed Caption is not activated Display is not shown in your language 5 2 01 5 31 PM
25. which may vary from state to state Some states do not allow limitation on how long an implied warranty lasts when an action may be brought or the exclusion or limitation of incidental or consequential damages so the above provisions may not apply to you REV 9 01 98 Before using the remote control transmitter batteries must first be installed HOW TO INSTALL BATTERIES 1 Open the battery compartment cover 2 Install two AAA penlight size batteries 3 Replace the battery compartment cover POWER SOURCE Use two AAA size penlight batteries supplied for the transmitter The batteries may last approximately one year depending on how much the remote control is used For best performance it is recommended that batteries should be replaced on a yearly basis or when the remote operation becomes erratic Do not mix old and new batteries or different types BATTERY PRECAUTIONS These precautions should be followed when using batteries in this device 1 Use only the size and type of batteries specified 2 Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment Reversed batteries may cause damage to the device 3 Do not mix different types of batteries together e g Alkaline and Carbon zinc or old batteries with fresh ones 4 If the device is not to be used for a long period of time remove the batteries to prevent damage or injury from possible batt
26. ys text captions or 1 2 of full screen text on the screen for hearing impaired viewers Front Audio Video In Jack A VCR or other video device may be hooked up V Chip The V Chip function can read the rating of a TV program or movie content if the program is encoded with this information V Chip will allow you to set a restriction level T ombination VHF UHF Antenna Single 75 ohm cable SEEM 300 ohm twin lead wire Ep o Splitter PERREN 89 75 OHM MATCHIN m off the Splitter E ee CHING not supplied UHF Antenna 300 ohm twin lead wire L f Antenna Single lt 9 ohim cable z 75 ohm cable A ohm ieai ie e ohm twin lead wire COMBINER not supplied me 2 MATCHING TRANSFORMER Incoming CATV not supplied i CONVERTER DESCRAMBLER FC 7 rw 5 S A 3J81301B E 2 company Combination VHF UHF Antenna Single 75 ohm cable or 300 ohm twin lead wire Connect the 75 ohm cable from a combination VHF UHF antenna to the antenna jack If your combination antenna has a 300 ohm twin lead wire use the 300 75 ohm matching transformer not supplied Combination VHF UHF Antenna Separate VHF and UHF 300 ohm twin leads Connect the UHF twin lead wire to a combiner not supplied Connect the VHF twin lead to the 300 75 ohm matching transformer not supplied Attach the transformer to the combiner Attach the combiner to the antenna jack Separ
Download Pdf Manuals
Related Search