Home

Enterasys VHIM Expansion Module

image

Contents

1. VHIM 2GT L3 1000BASE T GIGABIT ETHERNET EXPANSION MODULE QUICK INSTALLATION GUIDE ENTERASYS NETWORKS 9033695 01 NOTICE ONLY QUALIFIED PERSONNEL SHOULD PERFORM INSTALLATION PROCEDURES Enterasys Networks reserves the right to make changes in specifications and other information contained in this document without prior notice The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made The hardware firmware or software described in this manual is subject to change without notice IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL INDIRECT SPECIAL OR CONSEQUENTIAL DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO LOST PROFITS ARISING OUT OF OR RELATED TO THIS DOCUMENT WEB SITE OR THE INFORMATION CONTAINED IN THEM EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED OF KNEW OF OR SHOULD HAVE KNOWN OF THE POSSIBILITY OF SUCH DAMAGES Enterasys Networks Inc 500 Spaulding Turnpike Portsmouth NH 03801 2002 Enterasys Networks Inc All Rights Reserved Printed in the United States of America Order Number 9033695 March 2002 LANVIEW is a registered trademark of Enterasys Networks ENTERASYS NETWORKS NETSIGHT MATRIX WEBVIEW and any logos associated therewith are trademarks of Enterasys Networks SPECTRUM is a registered trademark of Aprisma Management Technologies Inc All other product names mentioned in this manual may be tradem
2. arks or registered trademarks of their respective companies FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with this user s guide may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation WARNING Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment INDUSTRY CANADA NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le pr sent appareil num rique n
3. at 5e 100 ohm 328 ft RJ 45 50 125 um or 62 5 125 um table seers multimode fiber ee MMF or SMF SC or ST below 1000Base SX Fiber Diameter Range 62 5 125 um MMF 160 MHz km 2 220 m 7 722 ft 200 MHz km 2 275 m 7 902 ft 50 125 um MMF 400 MHz km 2 500 m 7 1641 ft 500 MHz km 2 550 m 7 1805 ft 1000Base LX Fiber Bandwidth Range 2 m 5 km 16 404 ft 100Base T 1000Base T 1000Base SX 1000Base LX Diameter 9 um SMF 62 5 125 um MMF 500 MHz km 2 550 m 7 1805 ft 50 125 um MMF 400 MHz km 2 550 m 7 1805 ft 500 MHz km 2 550 m 7 1805 ft Note Network diameter is defined as the wire distance between two end stations in the same collision domain VERTICAL HORIZON FAST ETHERNET SWITCH 1000BASE T GIGABIT ETHERNET EXPANSION MODULE Enterasys s VHIM 2GT L3 1000Base T Gigabit Ethernet Expansion Module provides two Gigabit ports that can be used for a high speed backbone or server connections It contains two 1000Base T ports that can be connected to a site up to 100 m 328 ft away with Cat 5 Ethernet cable VHIM 2GT L3 C e1000 1000 eLink CO eLink CS act O act Gigabit Port LEDs Gigabit port LEDs are located on the front panel of the module to the left of the represented port These LEDs provide port status for at a glance network monitoring The following table details the indicator functions provided by the VHIM 2GT L3 Expa
4. hem from being unscrewed by hand 7 Connect the network cable Connect Ethernet cable to the port on the newly installed module See Connectivity Guidelines in this guide for further information Switch 8 Power on the switch Reconnect the previously removed power sources to the switch The switch s front panel LEDs should indicate the status of the new connection Check the LED indicators for the Gigabit port to ensure that they are operating correctly Refer to the table of LEDs in this guide for a description of the LED indications If the module does not respond see Troubleshooting below More details concerning connection options and network applications can be found in the VH 2402 L3 Installation Guide Information on the module s configuration options can be found in the Management Guide that is included with the base unit TROUBLESHOOTING If you experience any problems with the module check the following items before contacting Enterasys s Technical Support e Ensure the VH 2402 L3 switch with the Gigabit Expansion Module is powered up e Ensure that the device attached to the module is powered up and operating correctly e Ensure that the module is properly seated in the slot e Verify that the attached device is configured to match the communication mode used by the module 1 Gbps and half or full duplex e Check the connectors on both ends of
5. le connection to the switch 2 Remove network cables If you are replacing a module remove the cable attached to the port on the module 3 Loosen the screws on the installed module or slot faceplate Using your fingers or a flat head screwdriver turn the screws securing the module or faceplate on the slot in a counter clockwise direction until they are free of the chassis Be sure not to completely remove the screws from the module or faceplate 4 Remove the installed module or faceplate Firmly pull on the screws until the module is free of the switch Carefully slide the module straight out of the slot Keep the original faceplate for future use If you should remove the module replace the faceplate to prevent dust and debris from entering the unit and to maintain proper air flow switch son 08 00 or at oe ey bracket 5 Insert the new module into the switch Holding the new module with the text on the front panel upright carefully slide the module into the switch slot and press gently until it snaps into place Be sure the new module s front panel is flush with the switch panel Switch Module 6 Secure the new module Secure the new module in place by screwing the attached screws clockwise into the switch s chassis Tighten them enough to secure the module but not so tight as to prevent t
6. met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la class A prescrites dans le R glement sur le brouillage radio lectrique dict par le minist re des Communications du Canada ZOE HAMMER ESERIES VOU 1 ORR EIS 9 SAAR CT OBRE RE TMT S Loe hk PAW PLEMADEY COBSICMH Ee eRe ALSBRIKSILUGBOKT Class A ITE Notice WARNING This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures EC CONFORMANCE DECLARATION European contact Enterasys Networks Ltd Nexus House Newbury Business Park London Road Newbury Berkshire RG14 2PZ England This information technology product complies with ISO IEC Guide 22 and EN45014 It conforms to the following specifications EN55022 1988 CISPR 22 1985 Class A EN50082 1 IEC 1000 4 2 3 4 6 This information technology product complies with the requirements of the Low Voltage Directive 73 23 EEC and the EMC Directive 89 336 EEC and carries the CE Mark accordingly SAFETY WARNING Before installing or removing the VHIM 2GT L3 first disconnect the switch from the main power supply For full safety instructions please refer to the user guide that accompanies the switch Warning Optical Safety for Fiber CLASS I LASER Optic Modules DEVICE When using a fiber optic media expansion module never look at the transmit laser while it is po
7. nsion Module LEDs 1000 Steady Green Port operating at 1000Mbps in Full duplex mode established on the port the port INSTALLING THE MODULE CAUTION The VHIM 2GT L3 module is designed for the VH 2402 L3 switch only Do not try to install this module in any other units The VHIM 2GT L3 Expansion Module installs in the expansion slot on the front panel of the VH 2402 L3 switch To install the module follow the instructions below Equipment Checklist After unpacking the VHIM 2GT L3 Expansion Module check the contents of the box to be sure you ve received the following items e One VHIM 2GT L3 Expansion Module e This document Handling the Module CAUTION The VHIM 2GT L3 Expansion Module can easily be damaged by electrostatic discharge To prevent electrostatic damage observe the following guidelines e Do not remove the module from its packaging until you are ready to install it e Do not touch any of the module s pins connectors or components e Hold the module only by its edges or front panel e Wear an anti static wristband connected to a suitable earth ground whenever handling the module e Store or transport this module only in appropriate anti static packaging Instructions CAUTION The switch must be powered off before installing or replacing any module 1 Power off the switch Disconnect the AC power cord from the switch If a redundant power unit RPU is present disconnect its DC cab
8. the cable to be sure they are properly engaged
9. wered on Also never look directly at the fiber TX port and fiber cable ends when they are powered on Avertissment Sax T DISPOSITIF P LASER DE optiques s curit sur le CLASSE plan optique Ne regardez jamais le laser tant qu il est sous tension Ne regardez jamais directement le port TX Transmission fibres optiques et les embouts de c bles fibres optiques tant qu ils sont sous tension Warnhinweis Faseroptikanschl sse LASERGER T Optische Sicherheit DER KLASSE Niemals ein bertragungslaser betrachten w hrend dieses eingeschaltet ist Niemals direkt auf den Faser TX Anschlu und auf die Faserkabelenden schauen w hrend diese eingeschaltet sind SPECIFICATIONS Ports 2 1000Base T Communication Mode Half or full duplex auto negotiation for duplex mode and flow control Network Interface RJ 45 connector Cat 5e Ethernet cable Switch Method Store and forward Size 4 82 x 3 57 x 1 08 in 12 25 x 90 70 5 x 2 74 cm Power Consumption 2 4W maximum Temperature Operating 32 to 131 F 0 to 55 C Storage 40 to 131 F 25 to 55 C Humidity Operating 5 to 95 Emissions FCC Class A VCCI class A BSMI class A EN55022 Class A C Tick class A CE Mark Immunity IEC 1000 4 2 3 4 6 Standards IEEE 802 3ab Gigabit Ethernet ISO IEC 8802 3 Connector Max 10Base T Cat 3 4 5 100 m 100 ohm UTP 328 ft seis 100 m Cat 5 100 ohm 328 ft RJ 45 100 m C

Download Pdf Manuals

image

Related Search

Related Contents

The INSIDER  USER'S manUal  Manual de instrucciones  BB422 Series User Manual  FX3U-4AD-PNK-ADP USER`S MANUAL  User Manual - File Management  Arat NS1347 holder  th-22a/22at /22e th-42a/ 42at i 42e instruction manual  Samsung DVD-R121 manual de utilizador  HK654200XB EN User manual  

Copyright © All rights reserved.
Failed to retrieve file