Yamaha DME Musical Instrument User Manual
Contents
1. 255 255 255 0 H Wid The host address can be set from 2 to 253 for the Master device and from 3 to 253 for Slaves it Wid Always use a private address 192 168 0 2 through 192 168 255 253 unless it is absolutely necessary to use a global address Consult with the network administrator if it is necessary to use a global address DME Setup Manual 7 Master ID When a device is assigned as a Slave in Master Slave above this sets the host address for the Master device in that group This parameter cannot be set for the Master device O Link Mode Make sure that 100Base TX is selected 10 Ifthe system includes multiple DME devices repeat the above settings for each individual device Computer to DME Connection Refer to the DME manual for information on audio connection and further network connection details BEd Ifyou will be using CobraNet for audio connections the required bundle numbers and related settings must be made via the DME Designer application DMIA Ifyou will be using EtherSound for audio connections the routing and other EtherSound settings must be made via the AuviTran AVS ESMonitor software available from the AuviTran website http Wwww auvitran com view ohp products_AVS ESMonitor php Directly Connecting a Single DME Device to a Computer When only one DME device is to be controlled connect the device to the computer via a USB cable as described in DME Network Setup on2. environment USB Host Controller etc Even so simply disconnecting and connecting the USB cable will allow you to use the DME functions again DME Setup Manual Have you selected an appropriate network port in the To install one of either the DME Designer software or DME N Network Driver The software or driver can be individually installed by double clicking the Setup exe file located in the downloaded and extracted Installer DMEDesigner_ or Installer Networkdrv_ folder 1 To uninstall the DME Designer software The DME Designer software can be uninstalled either via Start Control Panel Add or Remove Programs or via Start Program Files gt YAMAHA OPT Tools DME Designer Uninstall To uninstall the DME N Network Driver The DME N Network Driver can be uninstalled via Start Control Panel Add or Remove Programs To uninstall the USB MIDI Driver The USB MIDI Driver can be uninstalled by double clicking the uninstall exe file located in the downloaded and decompressed Uninstall folder 18 Appendix DME64N 24N Network Setup via Panel Operation DME64N and DME24N device group and IP address settings can be made directly via the device s panel 1 Turn on the DME64N 24N power 2 Press the HOME key to display the main screen Level 1 On 1 Solo 1 igeScene 001 3 Press and hold the UTILITY key for more than 2 se
3. DME Designer application When the DME Designer is launched a new project will be created and a new zone Zone 1 will appear in the designer window DME Designer Main Panel Window es cr mo Ws tf pe Zone Scene Device Group m E p aj oy C i Speaker Processor M External Device i Picture rey gt Navigator Ellipse EXE Area Designer Window If the designer window shown above does not appear click the main panel window Show Hide button to reveal it 2 Place the appropriate DME objects in the designer window Select the required DME objects from the Toolkit window on the left of the display Objects can be dragged and dropped into the zone window or double clicked to place them in the current zone Drag and Drop or Double click DK Where required set the device group or sampling rate via the dialog box that appears when placing DME objects DKA Ifthe sampling rate set here and the actual sampling rate set for the DME operation are different excessive DSP may be required and operation may not be possible Be sure to match the sampling rates DME Setup Manual 12 3 As necessary double click placed DME object to open the DME configuration window Individual audio components can be placed and wired together as necessary to create configurations in the configuration window For this example you can leave the configuration empty Refer to the DME Designe
4. YAMAHA DME Setup Manual This manual describes the process of setting up a DME system from making the initial DME processor settings DME64N DME24N DMEBI C DME80 C DME4io C DME8I ES DME80 ES DME4io ES to synchronizing with the DME Designer application installed on a computer DKA For details about the DME units refer to the manual supplied with the specific device and for details about the DME Designer application refer to the pdf format DME Designer manual DKA In this document the term DME will refer to the DME64N DME24N DME8i C DME80 C DME4io C DME8i ES DME80 ES and DME4Iio ES while the term DME Satellite will refer only to the DME8i C DME8o0 C DME4io C DME8i ES DME8o0 ES and DME4io ES Software Installation DME Designer and DME N Network Driver installation page 3 USB MIDI Driver installation page 4 DME Network Setup page 6 Connecting via a USB cable and setting the DME IP address and Device Group Master Slave status from the DME Designer Computer to DME Connection page 8 The procedures for connecting a single DME unit to a computer as well as for connecting multiple DME units to a computer in the same subnet are described Refer to the DME manual for information on audio connection and further network connection details Computer Network Setup These settings must be made properly when connecting a computer to DME units via an Ethernet cable Computer TCP I
5. through 192 168 255 253 unless it is absolutely necessary to use a global address Consult with the network administrator if it is necessary t use a global address IP Address Network address Host address Master ID When a device is assigned as a Slave in Master Slave above this sets the host address for the Master device in that group This parameter cannot be set for the Master device Link Mode Make sure that 100Base TX is selected 19 DME N Network Driver Setup Details DME N Network Driver Window Select Start Control Panel DME N Network Driver to open the DME N Network Driver window The parameters in this window set up the device information to communicate with the DME N Network Driver gt DME N Network Driver Target Device List Device IP Address Device MAC Address Device Port No i 192 168 0 2 00 40 DE 25 15 48 1 192 168 0 4 00 40 DE 25 15 BO 1 192 168 0 5 00 40 DE 25 15 63 1 New Duplicate Remove Remove an Undo Device Name omes cl t SCSC W Device IP Address 192 fies fo 2 2 Device MAC Address 00 fao oe 2s is as Device Port No ji x Advanced stn O YAMAHA DME N Network Driver Ver 1 1 3 Copyright C 2004 2006 YAMAHA CORPORATION All Rights Reserved Save and Close Cancel Target Device List The name IP address MAC address and MIDI port number of all devices registered to communicate with
6. Device List Cancel Import setup from file Export setup to file BEd Ifthe IP address was not automatically detected register the DME device manually page 20 6 Select the DME unit that is to function as the Device Group Master from the Target Device List enter the Device Name and Device Port No and click the Apply button gt DME N Network Driver Target Device List Device IP Address Device MAC Address Device Port No DMEBi C 192 166 0 2 00 40 DE 25 15 46 Dee EE E New Duplicate Remove Remove an Undo Device Name DMESi C Device IP Address 192 ji i o 2 Device MAC Address fi 2s Device Port No 1 7 Apply Advanced Settings YAMAHA DME N Network Driver Yer 1 1 3 Copyright C 2004 2006 YAMAHA CORPORATION All Rights Reserved Save and Close Cancel Device Name Displayed as the port name in DME Designer Device Port No MIDI port number Set to 1 2 is also available for DME64N 24N devices 7 Click the Save and Close button to close the dialog box 11 DME Designer Operation Creating Configurations The process of launching the DME Designer application and combining and connecting various audio components to create configurations is described below The DME device s can be disconnected from the computer while creating configurations 1 Click Start gt All Programs gt YAMAHA OPT Tools gt DME Designer DME Designer to launch the
7. NETWORK 1 in the Rx field and click OK 8 Inthe main panel window click Network Setup in the Hardware menu to open the Network Setup dialog box CH Network Setup Q m Port List Tx Rx YAMAHA USB OUT 0 1 7 4M4HA4 USB IN 0 1 Network Setup Master Slave Master Slave ni be IP Address 192 168 0 3 G Utility ppe i Network Setup Word Clock Ctrl 8 a Monitor Out ctrl 9 Master ID 192 168 0 2 je Link Mode 10Base T 100Base TX O MAG Address 00 AO DE 25 15 AS Omnes 9 Make the following network settings then click OK MIDI Port List Tx Rx select YAMAHA USB OUT 0 1 YAMAHA USB IN 0 1 or Yamaha DME NETWORK 1 Yamaha DME NETWORK 1 as the DME port for the network settings Master Slave Selects Device Group Master or Slave status Master One device must be assigned as the Master in each Device Group Slave All other DME devices in the group should be set to Slave Bia When DME64N 24N and DME Satellite units are combined in a Device Group be sure to assign a DME Satellite unit as the Group Master IP Address set the IP addresses of the DME devices All DME devices in the same Device Group must be set to the same network address Network address Host address IP Address Master ID ii When only one DME device Master is used set the IP address to 192 168 0 2 Wud The subnet mask is fixed at
8. USB OUT 0 1 or Yamaha DME NETWORK 1 and when connected via Ethernet select the device name specified via the DME N Network Driver page 11 5 Select the Port item from the main panel window Setup menu to open the Port dialog box evice Group YAMAHA USB OUT 0 1 YAMAHA USB IN 0 1 DME Group No Assign No Assign gt i Cancel 6 Select the output and input ports specified in step 4 in the Tx and Rx fields and the appropriate Device Group in the Device Group field then click OK DME Setup Manual 14 7 Click the Synchronization item in the main panel window Tools menu to open the Synchronization dialog box DME objects placed in the DME Designer application will be displayed in the DME Designer list on the left and DME devices connected to the network will be displayed in the Network list on the right Synchronization il Go Off line Group DME Group z DME Designer Network IP Address IP Address DME4io 192 168 000 004 mn 992 168 000 004 DME4io C DME24N 192 168 000 007 maa 992 168 000 007 DME24N Message Close this window after synchronization V Store Project File into DME after synchronization BEd If multiple Device Groups have been set up select the Device Group to be synchronized from the Group list 8 Click the DME Designer list IP Address field and select the IP address corresponding to the DME device H Synchronization i Go Off l
9. before installing this software 1 Open the downloaded and extracted DME Designer Combo Installer V folder will be the version number on the actual file and double click the setup exe file located in the Installer folder The DME Designer Combo Installer setup dialog window will appear on the display DME Designer DME N Network Driver Ver 3 0 0 Welcome to the InstallShield Wizard for OME Designer Combo Please quit all applications 2 Follow the on screen instructions to install the software The DME Designer will be installed first followed by the DME N Network Driver If a previous version of the DME Designer and or DME Network Driver exists on the computer the older software will be uninstalled before installation of the new software begins After the older software has been uninstalled you will be asked to restart the computer In this case the computer must be restarted before the installation process can continue The installer will automatically be re launched and the installation will continue after the computer has been restarted The software will be installed in a DME Designer folder in the Program Files YAMAHA OPT Tools folder default DMIA Refer to the pdf format DME Designer manual for operating instructions The manual is not installed by the installer Download the manual separately from the Downloads page on the Yamaha Pro Audio website http www yamahaproaudio com B
10. combination of YAMAHA USB IN 0 2 and YAMAHA USB OUT 0 2 can also be used for the DME64N 24N Settings combining different port numbers i e YAMAHA USB IN 0 1 and YAMAHA USB OUT 0 2 or YAMAHA USB IN 0 2 and YAMAHA USB OUT 0 1 cannot be used Is the USB MIDI Driver Thru ON OFF parameter set to OFF Go to Start Control Panel Yamaha USB MIDI Driver and make sure that the Thru ON OFF parameter is set to OFF e Have you selected the same USB ports in both the DME Designer and another MIDI application Change the port setting so that the DME Designer and the other MIDI applications use different ports e Does the number of registered MIDI devices exceed the Windows limit The Windows operating system allows a maximum of 10 MIDI device drivers to be installed and registered In some cases changing the USB port to which a device is connected can cause it to be recognized as a different device thereby artificially exceeding the limit If MIDI doesn t function properly try uninstalling and then re installing the USB MIDI Driver Are you using the latest USB MIDI Driver supporting DME The latest driver supporting DME can be downloaded from the Yamaha website htto www yamahaproaudio com Did you launch DME Designer after connecting a USB cable and turning the device ON Be sure to connect the USB cable and turn the device on before launching DME Designer
11. immediately after an undo operation or after the control panel is launched Device information When a device that is registered for communication with the DME N Network Driver is selected in the Target Device List the communication parameters for that device can be viewed and edited in the device information fields Device Name This is the name of the device selected in the Target Device List The initial default settings are UNIT1 through UNIT256 but the name can be edited as required in this field Device IP Address The IP address of the device selected in the Target Device List can be set via these fields Refer to page 7 for details on checking and setting its IP address Bia The IP address must be set properly or communication with the device will not be possible Device MAC Address The MAC Media Access Control address of the device selected in the Target Device List can be set via these fields The MAC address of each device is permanently assigned when the device is manufactured and cannot be changed The MAC address parameter is included to prevent data from being sent to the wrong device if the IP address in inadvertently set incorrectly Refer to page 7 for details on checking its MAC address Bia The MAC address must be set properly or communication with the device will not be possible DKCH The MAC address of the connected device cannot be changed Device Port No The MIDI port number
12. shall terminate automatically and immediately without notice from Yamaha Upon such termination you must immediately destroy the licensed SOFTWARE any accompanying written documents and all copies thereof 4 DISCLAIMER OF WARRANTY ON SOFTWARE You expressly acknowledge and agree that use of the SOFTWARE is at your sole risk The SOFTWARE and related documentation are provided AS IS and without warranty of any kind DME Setup Manual NOTWITHSTANDING ANY OTHER PROVISION OF THIS AGREEMENT YAMAHA EXPRESSLY DISCLAIMS ALL WARRANTIES AS TO THE SOFTWARE EXPRESS AND IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NON INFRINGEMENT OF THIRD PARTY RIGHTS SPECIFICALLY BUT WITHOUT LIMITING THE FOREGOING YAMAHA DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR FREE OR THAT DEFECTS IN THE SOFTWARE WILL BE CORRECTED 5 LIMITATION OF LIABILITY YAMAHA S ENTIRE OBLIGATION HEREUNDER SHALL BE TO PERMIT USE OF THE SOFTWARE UNDER THE TERMS HEREOF IN NO EVENT SHALL YAMAHA BE LIABLE TO YOU OR ANY OTHER PERSON FOR ANY DAMAGES INCLUDING WITHOUT LIMITATION ANY DIRECT INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES EXPENSES LOST PROFITS LOST DATA OR OTHER DAMAGES ARISING OUT OF THE USE MISUSE OR INABILITY TO USE THE SOFTWARE EVEN IF YAMAHA OR AN AUTHORIZED DEALER HAS BEEN ADVISED OF THE POSSIBIL
13. the DME N Network Driver are shown in this list Click the title bars to sort accordingly When a device is selected in the list information related to that device will be viewed and edited in the Device information area below the list Device Name Device IP Address Device MAC Address Device Port No The name IP address MAC address and MIDI port number of the corresponding device Refer to the Device information area for details New Button Click this button to add a new device to the list Edit the device s parameters as required via the fields in the Device information area below the list the click the APPLY button to add the specified device Duplicate Button This button adds a device to the list by copying the data from the currently selected device Edit the new device s parameters as required via the fields in the Device information area below the list then click the APPLY button to add the specified device Remove Button Deletes the selected device from the list If the removed device is not the lowest device in the list all devices DME Setup Manual below the removed device will be shifted upward to maintain the continuity of the list Remove ALL Button Deletes all devices from the list Undo Button This button provides a one step undo function that allows you to undo a single operation and revert to the previous state The Undo button will be grayed out and inaccessible
14. 0 5 ar to Device List Cancel i j Import setup from file Export setup to file Auto Detect Allows automatic detection of connected devices that Can communicate with the DME N Network Driver A maximum of 254 addresses 4 through ax xxx 254 can be detected DMIA Only MAC addresses of devices on the same subnet as the computer can be detected Before searching for MAC addresses make sure that the computer is connected to the subnet to be searched and that an appropriate IP address is assigned 1 Detect from Specifies the start IP address for automatic detection 2 Detect to Specifies the end IP address for automatic detection 3 Currently searching Displays the IP address being checked during automatic detection No display when automatic detection is not in progress DME Setup Manual 4 Start Button Initiates automatic detection and causes the detected device list to be updated accordingly This button is grayed out and is not accessible during automatic detection 5 Abort Button Aborts automatic detection This button is grayed out when automatic detection is not in progress 6 Detected Device List This list shows all detected devices that are capable of communication with the DME N Network Driver No devices will be displayed initially Add Checkbox Checked devices will be added to the Target Device List when the Add to Device List bu
15. Control Panel gt DME N Network Driver to open the DME N Network Driver dialog box DME N Network Driver Target Device List Advanced Settings YAMAHA DME N Network Driver Yer 1 1 3 Copyright C 2004 2006 YAMAHA CORPORATION ll Rights Reserved Save and Close Cancel 3 Click the Advanced Settings button to open the Advanced Settings dialog box DME devices connected to the network can be automatically detected via this dialog box Advanced Settings Auto Detect Detect From 192 168 f fo Detect to 192 168 0 A 10 GI Add Device IP Address Device MAC Address Cancel Import setup From file Export setup to file 4 Enter the IP address range over which you would like to automatically detect connected DME devices in the Detect from and Detect to fields and click Start Automatic DME device detection will begin 5 When automatic DME device detection has finished check the Add box of the DME device DME Setup Manual that is to function as the Device Group Master and click Add to Device List The Advanced Seitings dialog box will close and return to the DME N Network Driver dialog box Advanced Settings Auto Detect Detect From fisz fies Jo iz Detect to 192 oO 10 Start Add Device IP Address Device MAC Address 192 168 0 2 00 40 DE 25 15 48 192 168 0 4 00 40 DE 25 15 B0 O 192 168 0 5 00 A0 DE 251563 Add to
16. G INSTALLING COPYING OR OTHERWISE USING THIS SOFTWARE YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE IF YOU DO NOT AGREE WITH THE TERMS DO NOT DOWNLOAD INSTALL COPY OR OTHERWISE USE THIS SOFTWARE IF YOU HAVE DOWNLOADED OR INSTALLED THE SOFTWARE AND DO NOT AGREE TO THE TERMS PROMPTLY DELETE THE SOFTWARE 1 GRANT OF LICENSE AND COPYRIGHT Yamaha hereby grants you the right to use the software program s and data SOFTWARE accompanying this Agreement The term SOFTWARE shall encompass any updates to the accompanying software and data The SOFTWARE is owned by Yamaha and or Yamaha s licensor s and is protected by relevant copyright laws and all applicable treaty provisions While you are entitled to claim ownership of the data created with the use of SOFTWARE the SOFTWARE will continue to be protected under relevant copyrights e You may use the SOFTWARE on your computer s e You may make one or reasonable copies of the SOFTWARE in machine readable form for backup purposes only if the SOFTWARE is on media where such backup copy is permitted On the backup copy you must reproduce Yamaha s copyright notice and any other proprietary legends that were on the original copy of the SOFTWARE You may permanently transfer to a third party all your rights in the SOFTWARE provided that you do not retain any copies and the recipient reads and agrees to the terms of this Agreement RESTRICTIONS e You may not engage in rever
17. ITY OF SUCH DAMAGES In no event shall Yamaha s total liability to you for all damages losses and causes of action whether in contract tort or otherwise exceed the amount paid for the SOFTWARE 6 THIRD PARTY SOFTWARE Third party software and data THIRD PARTY SOFTWARE may be attached to the SOFTWARE If in the written materials or the electronic data accompanying the Software Yamaha identifies any software and data as THIRD PARTY SOFTWARE you acknowledge and agree that you must abide by the provisions of any Agreement provided with the THIRD PARTY SOFTWARE and that the party providing the THIRD PARTY SOFTWARE is responsible for any warranty or liability related to or arising from the THIRD PARTY SOFTWARE Yamaha is not responsible in any way for the THIRD PARTY SOFTWARE or your use thereof e Yamaha provides no express warranties as to the THIRD PARTY SOFTWARE IN ADDITION YAMAHA EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE as to the THIRD PARTY SOFTWARE e Yamaha shall not provide you with any service or maintenance as to the THIRD PARTY SOFTWARE e Yamaha is not liable to you or any other person for any damages including without limitation any direct indirect incidental or consequential damages expenses lost profits lost data or other damages arising out of the use misuse or inability to use the THIRD PARTY
18. P settings page 9 DME N Network Driver settings page 11 DME Designer Operation Creating Configurations page 12 Explains the process of launching the DME Designer application and combining and connecting various audio components to create configurations Going Online page 14 Explains how to go online and transfer configurations created using the DME Designer application to DME devices Troubleshooting page 17 Appendix DME64N 24N Network Setup via Panel Operation page 19 DME N Network Driver Setup Details page 20 DME Setup Manual 1 Software Installation Begin by downloading the DME Designer Combo Installer and the USB MIDI Driver from the Downloads page on the Yamaha Pro Audio website htto www yamahaproaudio com System Requirements 1 GHz or higher Intel Core Pentium Celeron family processor 1 4 GHz or higher Intel Core Pentium Celeron family processor DME Setup Manual 2 DME Designer and DME N Network Driver Installation ee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee ee Install the DME Designer application and DME N Network Driver from the DME Designer Combo Installer by following the procedure outlined below DMIA The following procedure is applicable even if an older version of the DME Designer and or DME N Network Driver is already installed DK Be sure to read the license agreement at the end of this document
19. SOFTWARE 7 GENERAL This Agreement shall be interpreted according to and governed by Japanese law without reference to principles of conflict of laws Any dispute or procedure shall be heard before the Tokyo District Court in Japan If for any reason a court of competent jurisdiction finds any portion of this Agreement to be unenforceable the remainder of this Agreement shall continue in full force and effect 8 COMPLETE AGREEMENT This Agreement constitutes the entire agreement between the parties with respect to use of the SOFTWARE and any accompanying written materials and supersedes all prior or contemporaneous understandings or agreements written or oral regarding the subject matter of this Agreement No amendment or revision of this Agreement will be binding unless in writing and signed by a fully authorized representative of Yamaha U R G Pro Audio amp Digital Musical Instrument Division Yamaha Corporation 2007 Yamaha Corporation MW BO 22
20. Was the USB cable disconnected during operation If the USB cable is accidentally disconnected DME designer will not recognize the device even if the cable is reconnected You will have to restart DME Designer When controlling the DME from your computer via Ethernet the DME does not operate correctly e Is the Ethernet cable connected correctly e Is the DME N Network Driver set up appropriately Did you enter an appropriate IP address Is the computer network setup appropriate Select Start gt Control Panel Network Connections Local Area Connection and confirm the network setup Are the settings of DME and peripheral network devices including switching hubs appropriate Refer to the relevant owner s manuals for the DME and peripheral network devices including switching hubs for details DME Designer Are you using the latest DME N Network Driver supporting DME The latest driver supporting DME can be downloaded from the Yamaha website htto www yamahaproaudio com Do you have security software running on your system Try to disable the security software once Set it to allow use of TCP port 12300 on the network card being used by the DME N Network Driver Cannot suspend or resume the computer correctly e Do not suspend the computer while the DME Designer is running If you are using Windows 2000 you may not be able to Suspend resume normally depending on the particular
21. al 1 Start the computer and log on with administrator privileges while power to the DME is off 2 Select Start gt Control Panel and then Switch to Classic View in the upper left of the display to show all control panels and icons 3 Select System gt Hardware gt Driver Signing File Signature Verification and check the radio button to the left of Ignore lInstall all files regardless of file signature and click OK Restore this setting to its original state after the installation has been completed 4 While the DME power is still off connect the computer to the DME unit via a USB cable 5 Turn the DME power on and the Found New Hardware Wizard message will appear automatically 6 Select Install from a list or specific location Advanced gt Search for the best driver in these locations check only Include this location in the search click Browse to specify the downloaded and extracted Driver folder then click OK 7 Click Next to start the installation 8 Whena message appears indicating that the driver has been successfully installed click Finish 9 Restart the computer when a message appears prompting you to do so The driver has been installed E Windows 2000 1 Start the computer and log on with administrator privileges while power to the DME is off 2 Select My Computer gt Control Panel gt System gt Hardware gt Driver Sign
22. are Device Manager The Device Manager window appears 2 Make sure that no or x marks appear at Universal serial bus controller or USB Root Hub If you see the or x mark the USB controller is disabled Refer to the owner s manual of your computer for details e Is any unknown device registered If driver installation fails the DME will be shown as an Unknown device and you will not be able to install the driver Delete the Unknown device by following the steps below 1 Select Start Control Panel System gt Hardware Device Manager The Device Manager window appears 2 Look for Other devices 3 i you find Other devices double click it to extend the tree to look for Unknown device If one appears select it and click the Remove button 4 Remove the USB cable from the DME and make the connection again 5 Install the driver again according to the instructions described on page 4 DME Setup Manual When controlling the DME from your computer via USB the DME does not operate correctly e Did you install the USB MIDI driver e Is the USB cable connected correctly e Have you selected an appropriate port in the DME Designer Make sure that the settings in the DME Designer have the combination of YAMAHA USB IN 0 1 Yamaha DME NETWORK 1 and YAMAHA USB OUT 0 1 Yamaha DME NETWORK 1 The
23. cess gt Get Word Glock Fs lt Success gt Start Event Logger lt Success gt Start Event Scheduler lt Success gt Start Wave Manager lt Success gt Start Monitoring Point List lt Success gt Get Component Preset OME4io O Setup lt Success gt Get Component Preset DME24N Setup lt Success gt Transmission complete PTT TTT TT be TT TT TT Close this window after synchronization J Store Project File into DME after synchronization To go offline either click the main panel window On line button or the Go Off line button in the Synchronization dialog box For more in depth information on using the DME Designer application for system design refer to the pdf format DME Designer manual If you will be using CobraNet for audio connections the required bundle numbers and related settings must be made via the DME Designer application If you will be using EtherSound for audio connections the routing and other EtherSound settings must be made via the AuviTran AVS ESMonitor software DME Setup Manual 16 Troubleshooting The USB MIDI Driver cannot be installed e Is the USB cable connected correctly e Is the USB function enabled on your computer When you connect the DME to the computer for the first time if the Add New Hardware Wizard does not appear the USB function on the computer may be disabled Perform the following steps 1 Select Start Control Panel System gt Hardw
24. conds to display the Utility screen Infa Het Oi F Lack Labe COHE 24H Jers igon CUS ae J BS APr 2a 15 ag 14 Bat tery COR J 4 Press the UTILITY a few times until the Net page appears Info Het Dise Lock fF Naster Slave IF Ad 132 165 Gee Ae O master ID l Q Link Mode eabASE Tx HAC Adr CeBRGDESSeer9 DME Setup Manual 5 Use the A and V keys to move the cursor to the parameters listed below and press the ENTER key The corresponding editing dialog will appear Make the settings indicated for each parameter below and press the ENTER key each time to confirm and enter the settings Master Slave Selects Device Group Master or Slave status Master One device must be assigned as the Master in each Device Group Slave All other DME devices in the group should be set to Slave DK When DME64N 24N and DME Satellite units are combined in a Device Group be sure to assign a DME Satellite unit as the group Master IP Address Set the IP addresses of the DME devices All DME devices in the same Device Group must be set to the same network address DK When only one DME device Master is used set the IP address to 192 168 0 2 DLH The subnet mask is fixed at 255 255 255 0 DLH The host address can be set from 2 to 253 for the Master device and from 3 to 253 for Slaves Bid Always use a private address 192 168 0 2
25. ction The Local Area Connection Properties dialog box will be displayed 2 Select Internet Protocol Version 4 TCP Ipv4 on the Networking tab then click Properties The Internet Protocol Version 4 TCP IPv4 Properties dialog box will be displayed 3 Click Use the following IP address on the General tab 4 Enter your computer s IP address into IP address the Gateway s IP address into Default gateway and 255 255 255 0 into Subnet mask BL When the computer and DME devices are connected in the same subnet as described on page 8 the network address must be set to that same address as the DME devices while the host address must be set to a different value DK When the computer and DME devices are connected in the same subnet Set the gateway IP host address to 254 Internet Protocol Version 4 TCP IPv4 Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 192 168 0 100 Subnet mask 255 255 255 0 Default gateway 192 168 0 254 Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server 5 Click OK 6 Restart your computer DME Setup Manual E W
26. ents gt e ex Eee DME Designer Amy Music Emy Pictures Br Setup01 F Setup02 File name Untitled Save as type Project File with wave daf Cancel l Security ID Administrator Password Confirm Password DME Setup Manual 13 Going Online After connecting the computer to the DME devices and going online you can transfer configurations created using the DME Designer application to the DME devices The DME devices and DME Designer are online when they are connected and able to communicate with each other DME devices can also be controlled in real time when online 1 Connect the DME devices to the computer as described on page 8 and turn the DME power on 2 Launch the DME Designer application select the Open command from the main panel File menu and open the previously saved project file Bia The DME Designer can also be launched and the project file automatically loaded by simply double clicking the project file icon 3 Click the MIDI Setup button to open the MIDI dialog box DMIA Ifthe DME ports are not displayed check that the DME power is on and re launch the DME Designer application Device Microsoft GS Wavetable SW Synth YAMAHA USB OUT 0 1 YAMAHA USB OUT 0 2 Cancel 4 Select the input and output ports to be used to control the Device Group Master then click OK When connected via USB select YAMAHA USB IN 0 1 or Yamaha DME NETWORK 1 and YAMAHA
27. ia DME Designer V3 cannot communicate with DME devices using firmware version 2 or earlier If you are using DME Designer V3 be sure to update the DME device firmware to the latest version that can be downloaded from Yamaha Pro Audio website http www yamahaproaudio com DK The installer will launch automatically when the computer is restarted after the uninstall process but in rare cases the installer may be hidden by the task bar In such cases click this icon to continue the installation DME Setup Manual 3 USB MIDI Driver Installation DMIA You can also refer to the installation guide supplied with the driver for detailed installation procedures E Windows Vista E Windows XP Start the computer and log on with administrator privileges while power to the DME is off Connect the computer to the DME unit via a USB cable Turn the DME power on Found New Hardware will be displayed Select Locate and install driver software recommended Don t search online When a message appears prompting you to insert the supplied disc select I don t have the disc Show me other options Browse my computer for driver software advanced gt Browse specify the downloaded and extracted Driver folder then click OK Click Next to start installation When a message appears indicating that the driver has been successfully installed click Finish The driver has been installed DME Setup Manu
28. igned as the master device IP Address All devices to be included in the same group must be assigned the same network address The Device Group Master is specified by its host address Network address Host address IP Address Master ID USB cable 2 Turn the DME power on 3 Click Start gt All Programs gt YAMAHA OPT Tools gt DME Designer DME Designer to launch the DME Designer application 4 Click the MIDI Setup button to open the MIDI dialog box BEd Ifyou can t locate the MIDI Setup button on the display it is most probably hiding in the taskbar Double click it to open the MIDI dialog box Device In YAMAHA USB IN 0 1 YAMAHA USB IN 0 2 AMARA USB DUT D YAMAHA USB OUT 0 2 MIDI Pad cA det BE og Cancel Help 5 Select the YAMAHA USB IN 0 1 or Yamaha DME NETWORK 1 input port in the In field and the YAMAHA USB OUT 0 1 or Yamaha DME NETWORK 1 output port in the Out field and click OK BEd Ifthe DME port does not appear in the MIDI dialog box check that the DME device s power is turned on and re launch the DME Designer application DME Setup Manual 6 6 From the DME Designer main panel click Port in the Setup menu to open the Port dialog box Device Group YAMAHA USB IN 0 1 No Assign No Assien 7 Select YAMAHA USB OUT 0 1 or Yamaha DME NETWORK 1 in the Tx field and YAMAHA USB IN 0 1 or Yamaha DME
29. indows XP 1 Select Start gt Control Panel The Control Panel is displayed 2 If the Control Panel is in Category display click Switch to Classic View 3 Double click Network Connections gt Local Area Connection The Local Area Connection Status dialog box will be displayed 4 Click Properties on the General tab The Local Area Connection Properties dialog box will be displayed 5 Select Internet Protocol TCP IP on the General tab then click Properties The Internet Protocol TCP IP Properties dialog box will be displayed 6 Click Advanced then Properties on the Options tab The TCP IP Filtering dialog will be displayed 7 Select Permit All for TCP Ports then click OK The display returns to the Advanced TCP IP Settings dialog Click OK to return to the Internet Protocol TCP IP Properties dialog TCP IP Filtering Enable TCP IP Filtering All adapters Permit All Permit All Permit All Permit Only Permit Only Permit Only TCP Ports UDP Ports IP Protocols 8 Click Use the following IP address on the General tab 9 Enter your computer s IP address into IP address the Gateway s IP address into Default gateway and 255 255 255 0 into Subnet mask BL When the computer and DME devices are connected in the same subnet as described on page 8 the network addres
30. ine Close Group DME Group s DME Designer Network DME4io 192 168 000 004 192 168 000 Select IP Address 192 168 aul eu IP Address mmm 192 168 000 004 DME4io C mm1 92 168 000 00 DME24N 9 Click the Go On line button and a dialog box confirming the sync direction will appear A Sync Direction DME Designer gt Device DME Designer lt Device i Cancel DME Setup Manual 15 10 Select the DME Designer gt Device button then click OK and the DME Designer configuration will be transferred to the DME device When synchronization has finished the Go On line button will be grayed out and the main panel window On line button will light DKA When a configuration has already been transferred to a DME unit we recommend using the DME Designer lt Device button for synchronization The transfer time is faster than using the DME Designer gt Device button However if the configuration has been edited it is necessary to use the DME Designer gt Device button Synchronization Go On line Go Off line Group DME Groupi Device Group DME Designer Network Mute Rx Tx IP Address DME4io G 192 168 000 004 mn 192 168 000 004 DME4io C DME24N 192 168 000 007 mza 92 168 000 007 DME24N Message Clear Zone ID lt Success gt Write Zone ID lt Success gt Synchronize Zone lt Success gt Recall Scene No 1 lt Success gt Get Word Clock Fs lt Suc
31. ing gt File Signature Verification and check the radio button to the left of Ignore lInstall all files regardless of file signature and click OK Restore this setting to its original state after the installation has been completed 3 While the DME power is still off connect the computer to the DME unit via a USB cable 4 Turn the DME power on and the Found New Hardware Wizard message will appear automatically Click Next 5 Select Search for a suitable driver for my device recommended Specify a location click Browse to specify the downloaed and extracted Driver folder then click OK 6 Click Next to start the installation 7 Whena message appears indicating that the driver has been successfully installed click Finish 8 Restart the computer when a message appears prompting you to do so The driver has been installed DME Setup Manual DME Network Setup After connecting the computer to the DME unit via a USB cable the Device Group and IP address for each DME unit can be individually set from the DME Designer DK These parameters can also be set directly via the panel controls and displays of the DME64N and DME24N page 19 Device Group When a system uses multiple DME units the DME units can be controlled from the DME Designer application in Device Groups Since all devices in a group are controlled via the Device Group Master one device in each group must be ass
32. of the device selected in the Target Device List can be set via this menu The MIDI port number also functions as device ID number It can be set to 1 or 2 for DME64N 24N units It should be set to 1 for DME Satellite units DK The MIDI port number must be set properly or communication with the device will not be possible Apply Button Click the Apply button after editing the Device Name Device IP Address Device MAC Address or Device Port No parameters to actually apply the changes Also 20 devices added to the Target Device List by pressing the NEW or DUPLICATE buttons will only actually be registered for communication with the DME N Network Driver when the Apply button is pressed Advanced Settings Button Opens the Advanced Settings window This window provides access to advanced settings For details refer to the section below Advanced Settings Window Click the Advanced Settings button in the DME N Network Driver window to open the Advanced Settings window The parameters in this window set up the DME N Network Driver for automatic device detection and allow saving and loading setup files Advanced Settings Auto Detect Oe From 194 168 fo j2 2 192 168 OF 10 at Start 5 Device MAC Address 00 40 DE 25 15 46 00 40 DE 25 15 B0 00 40 DE 25 15 63 dd Device IP Address Device Name 192 168 0 2 DME8i C 192 165 0 4 192 168
33. page 6 USB cable Connecting Multiple DME Devices to a Computer in the Same Subnet Connect multiple DME devices to the computer via a switching hub and Ethernet cables Device Group Ethernet straight cable Ethernet straight cable Computer IP Address 192 168 0 100 DME Satellite IP Address 192 168 0 3 Master ID 2 DME64N 24N IP Address 192 168 0 250 Master ID 2 BEd It is possible to connect the computer to the Device Group Master using a USB cable It is also possible to connect the computer to a Slave DME using a USB cable if a DME Satellite is assigned as the Device Group Master BEd Use a switching hub that is capable of 100Base TX operation Bia The maximum length of cables that can be used to connect DME units to a switching hub is 100 meters Proper operation at this length however will depend on the quality of the hub and cables used and cannot be guaranteed Bia Use CAT5 STP shielded twisted pair type cable to maximize resistance to electromagnetic interference DME Setup Manual 8 Computer Network Setup These settings must be made when DME devices are connected via Ethernet cables Computer TCP IP Settings The computer s IP address and TCP IP filtering must be set up to allow network communication with the DME device s E Windows Vista 1 Select Start gt Control Panel gt Network and Sharing Center Manage network connections Local Area Conne
34. r manual for detailed information on creating configurations i Desiener Sele g E gt iz ty H Ch ion iE Os i dh as z i DME8i CZonel DME Group Confieuration1 E fo x E Ambient Noise Compensi a 4 Audio Detector Auto Gain Control H Crossover Crossover Processor aCrossover ProcessorI fe Delay fl Dynamics H BEQ Fader H Feedback Suppressor Filter El Meter i Miscellaneous Mixer i Auto Mixer o 2 Channel Channel CobraNet Input ice D Eee a 12 Channel EE 16 Channel H Auto Mixerl m Delay Matrix Matrix Mixer 4 Select the Scene Manager item from the main panel window Tools menu to open the Scene Manager dialog box The specified configuration parameter settings can be saved as a scene via the Scene Manager dialog box Scene Manager Cut Copy Paste Insert Clear Recall Safe DME Group Benetin Nane centiewation _ Edt Secu Recall Securit Fade Fade Mode Level 1 Level 1 i OFF No Data No Data No Data No Data No Data No Data No Data No Data No Data No Data No Data b Scene Link Recall Detail gt gt LA 5 Select the row containing the scene you want to save and click the Store button 6 Configurations and other settings can be saved as project files daf extension by selecting the Save As command from the main panel window File menu Save n My Docum
35. s must be set to that same address as the DME devices while the host address must be set to a different value Bia When the computer and DME devices are connected in the same subnet Set the gateway IP host address to 254 Internet Protocol TCP IP Properties General fou can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 192 168 0 100 Subnet mask 255 255 255 0 Default gateway 192 168 0 254 Use the following DNS server addresses Preferred DNS server Alternate DNS server 10 Click OK 11 Restart your computer E Windows 2000 1 Select Start gt Settings gt Control Panel gt Network and Dial Up Connections gt Local Area Connection The Local Area Connection Status dialog box will be displayed 2 Steps 4 and after are the same as for Windows XP DME Setup Manual 10 DME N Network Driver Settings In order for the computer to recognize the DME device s it is necessary to register the IP address and device name of the DME device that is the Device Group Master 1 Connect the DME device s to the computer as described on page 8 and turn the DME power on 2 Double click Start gt
36. se engineering disassembly decompilation or otherwise deriving a source code form of the SOFTWARE by any method whatsoever You may not reproduce modify change rent lease or distribute the SOFTWARE in whole or in part or create derivative works of the SOFTWARE You may not electronically transmit the SOFTWARE from one computer N to another or share the SOFTWARE in a network with other computers You may not use the SOFTWARE to distribute illegal data or data that violates public policy You may not initiate services based on the use of the SOFTWARE without permission by Yamaha Corporation Copyrighted data including but not limited to MIDI data for songs obtained by means of the SOFTWARE are subject to the following restrictions which you must observe Data received by means of the SOFTWARE may not be used for any commercial purposes without permission of the copyright owner Data received by means of the SOFTWARE may not be duplicated transferred or distributed or played back or performed for listeners in public without permission of the copyright owner The encryption of data received by means of the SOFTWARE may not be removed nor may the electronic watermark be modified without permission of the copyright owner 3 TERMINATION This Agreement becomes effective on the day that you receive the SOFTWARE and remains effective until terminated If any copyright law or provisions of this Agreement is violated the Agreement
37. tton below is clicked Devices that are already registered cannot be checked Device IP Address The IP address of the corresponding detected device Device Name If a name has been registered for the detected device it will be displayed here otherwise no name will be displayed Device MAC Address The MAC address of the corresponding detected device 7 Add to Device List Button Devices with checked Add checkboxes will be added to the Target Device List when this button is clicked Cancel Button Closes the window without making any changes 9 Import Setup from File Button When working in a different environment it is possible to load a previously saved setup file Click to open the Open window Select a setup file and then click the Open button to import the corresponding settings Export Setup to File Button lt is possible to save the setup data to a file that can then be reloaded when working in a different environment Click to open the Save As window Enter a file name and click the Save button to save the setup file 21 ATTENTION SOFTWARE LICENSE AGREEMENT PLEASE READ THIS SOFTWARE LICENSE AGREEMENT AGREEMENT CAREFULLY BEFORE USING THIS SOFTWARE YOU ARE ONLY PERMITTED TO USE THIS SOFTWARE PURSUANT TO THE TERMS AND CONDITIONS OF THIS AGREEMENT THIS AGREEMENT IS BETWEEN YOU AS AN INDIVIDUAL OR LEGAL ENTITY AND YAMAHA CORPORATION YAMAHA BY DOWNLOADIN
Download Pdf Manuals
Related Search