Sony AIR-SW10Ti Speaker User Manual
Contents
1. Lights up when the sub unit is turned on Flashes when the sub unit is turned off Note If you set S AIR STANDBY to ON no sound will be output from the main unit or the subwoofer when the power of the main unit is off Using the coupling operation with the optional sub unit and optional S AIR remote commander This system is compatible with the coupling operation The coupling operation establishes a connection between the optional sub unit and optional S AIR remote commander For details refer to the Operating Instructions of the optional S AIR remote commander Troubleshooting 1 Make sure the power cord is correctly and firmly connected 2 Find your problem in the checklist below and take the indicated corrective action If the issue persists contact your nearest Sony dealer When bringing the product in for repairs be sure to bring in the entire system main unit subwoofer and wireless transceivers This product is a system product and the entire system is needed to determine the section requiring repair If the STANDBY indicator on the main unit I C indicator on the subwoofer flashes Press 1 T on the main unit or the subwoofer to turn it off then unplug the power cord After checking that there is no indication on the display reconnect the power cord and press 1 T to turn on the main unit or the subwoofer If the issue persists contact you2. Wireless Speaker System 5 2 1 Q 9 The subwoofer can be placed with the speaker side up Remote RM ANU066 This manual mainly explains operations using the remote but the same operations can also be performed using the buttons on the unit having the same or similar names To use the remote Slide and remove the battery compartment lid and insert the two supplied R03 size AAA batteries side first matching the polarities shown below Notes on using the remote With normal use the batteries should last for about six months Do not mix an old battery with a new one or mix different types of batteries e If you do not intend to use the remote for a long period of time remove the batteries to avoid damage from battery leakage and corrosion Getting Started Hooking up the system Main unit Wall socket Subwoofer Wall socket lt FM lead antenna extend horizontally White side for North American model Brown side for other models Wireless transceiver EZW RT10A Wireless transceiver Insert the supplied wireless transceiver EZW RT10A securely into the EZW RT10A slot on the rear panel of main unit and the subwoofer Check the orientation of the V mark when inserting the supplied wireless transceivers EZW RT10A Failure to do so may result in
3. or 160 then press ENTER 12 The default setting is 120 5 Press SYSTEM MENU 18 to exit the system menu SUBWOOFER PHASE In some cases main unit and subwoofer sound integration may be unsatisfactory due to phase cancelation which can be remedied by reversing the subwoofer s phase as follows 1 Press SYSTEM MENU 18 2 Press 20 repeatedly until SOUND appears then press ENTER 12 3 Press 20 repeatedly until SW PHASE appears then press ENTER 12 4 Press 20 to select NORMAL or REVERSE then press ENTER 12 The default setting is NORMAL 5 Press SYSTEM MENU 18 to exit the system menu PAE This function restores the treble frequencies lost during sound compression naturally recreating the original sound 1 Press SYSTEM MENU 18 2 Press 20 repeatedly until SOUND appears then press ENTER 12 3 Press 20 repeatedly until PAE appears then press ENTER 12 4 Press 20 to select ON or OFF then pressing ENTER 12 The default setting is OFE 5 Press SYSTEM MENU 18 to exit the system menu BASS BOOST You can boost the lower frequencies of sound sources for deeper sound
4. MULTI or PARTY The selected S AIR mode appears The default setting is underlined MULTI SOURCE Select this setting to listen to different sound sources on each sub unit PARTY Select this setting to listen to the same sound source on multiple sub units Notes When you change the S AIR mode the iPod channel is automatically selected for the connected sub units When connecting the main unit to a sub unit that is not compatible with the MULTI SOURCE mode set the main unit to the PARTY mode You can then select the S AIR channel from the sub unit When you select the PARTY mode select the function iPod or TUNER by pressing PARTY CH 15 repeatedly Using sub units when the main unit is off S AIR STANDBY mode You can stream the setting information and music to a sub unit from a unit via S AIR even when the main unit is turned off 1 Press SYSTEM MENU 18 2 Press 20 repeatedly until S AIR appears then press ENTER 12 3 Press 20 repeatedly until STANDBY appears then press ENTER 12 4 Press 20 to select ON When you set S AIR STANDBY to ON you can listen to music from a sub unit even if the main unit is turned off When the main unit is turned on you can listen to music from the main unit subwoofer and sub unit If you set the S AIR STANDBY to ON S AIR in the display on the main unit is as follows
5. lights up 7 Turn off the system Press 1 1 The system turns on 15 seconds before the preset time If the system is on at the preset time the Play Timer will not function Do not operate the system from the time the system turns on until playback starts To check the setting 1 Press CLOCK TIMER 16 SELECT flashes 2 Press ENTER 12 Press 20 repeatedly until PLAY SEL appears then press ENTER 12 To cancel the timer Repeat the same procedure above until OFF in step 3 and then ENTER 12 To change the setting Start over from step 1 Notes for the iPod iPhone user Make sure the iPod iPhone is not playing when using the Play Timer The Play Timer may not be activated depending on the status of the connected iPod iPhone Tip The Play Timer setting remains as long as the setting is not canceled manually Enjoying the music in multiple rooms using the optional sub units When you listen to music from an optional sub unit you can use the following functions Selecting the S AIR mode PARTY mode MULTI SOURCE mode When connecting to multiple sub units you can listen to different sound sources on each sub unit MULTI SOURCE mode or the same sound source on each sub unit PARTY mode by selecting the S AIR mode accordingly Press S AIR MODE 25 repeatedly to select
6. of the polarized or Corporation is under license Other trademarks and trade 10 Protect the power cord from being walked on or pinched names are those of their respective owners All other trademarks and registered trademarks are of their respective holders In this manual and marks are not specified grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the 12 Use only with the cart stand tripod 13 Unplug this apparatus during lightning storms or when 14 Refer all servicing to qualified service personnel The following FCC statement applies only to the version of this model manufactured for sale in the U S A Other versions may not comply with FCC technical regulations NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency en
7. set at the factory to A 4 Confirm the connection status Once connection between the main unit and the subwoofer is established the S AIR indicator 9 on the subwoofer lights up Tip You can also connect up to 10 optional sub units to the main unit In this case set the S AIR ID to the same ID as the main unit For details on the S AIR ID of the sub unit refer to the Operating Instructions supplied with the sub unit Identifying the subwoofer with your main unit Pairing operation It is easy to set the same S AIR ID for the main unit and the subwoofer to establish the connection However if a neighbor has an AIR SW10Ti system with the same S AIR ID as your S AIR main unit the neighbor may be able to hear the audio transmitted from your main unit on the neighbor s subwoofer Also you may be able to hear the audio transmitted from your neighbor s main unit on your subwoofer To prevent this you can identify the subwoofer with your main unit by performing the pairing operation Before pairing Connection is established by the S AIR ID example Neighboring Your AIR SW10Ti system AIR SW10Ti system Subwoofer Subwoofer ID A ID A oN oN eG Ae eS LK n PD oN ATN EON a oN a AA ID A ID A Main unit Main unit After pairing Connection is established between the subwoofer and your main unit Neighboring Your AIR SW10Ti system
8. subwoofer closer together Stop using any equipment that generates electromagnetic energy such as a microwave oven Place the main unit and subwoofer away from other wireless devices Stop using any other wireless devices Change the S AIR ID settings of the main unit and subwoofer Change the RF CHANGE setting on the main unit The S AIR channel fails to change when you connect the main unit to an optional sub unit Check that the main unit and sub unit are connected properly If you are using a sub unit which is not compatible with the MULTI SOURCE mode set the main unit to the PARTY mode iPod iPhone There is no sound Make sure the iPod iPhone is connected securely Make sure the iPod iPhone is playing music Adjust the volume of the main unit Update your iPod iPhone to use the latest software The iPod iPhone cannot be operated by the main unit Check that the iPod iPhone and main unit are connected properly Depending on the iPod iPhone model you are using and its status it may not be possible to operate the iPod iPhone using the main unit Update your iPod iPhone to use the latest software The sound is distorted Turn down the volume of the main unit Set the EQ setting of the iPod iPhone to Off or Flat The iPod iPhone cannot be charged Make sure the iPod iPhone is connected securely Check that the power cord is connected se
9. turn off the clock display to minimize the amount of power consumed power save mode Press DISPLAY 19 when the clock is displayed Press the button again to display the clock Note When displaying the menu no information appears in the display Using the timers The system offers two timer functions If you use both timers the Sleep Timer has priority Sleep Timer You can fall asleep to music This function works even if the clock is not set Press SLEEP 17 repeatedly to select the setting time OFF 90min 30min 20min 10min gt OFF Play Timer You can wake up to iPod iPhone or tuner at a preset time Make sure you have set the clock 1 Press VOLUME 8 to adjust the volume 2 Press CLOCK TIMER 16 3 Press 20 repeatedly until PLAY SET appears then press ENTER 12 ON TIME appears and the hour indication flashes 4 Set the time to start playback Press 20 repeatedly to set the hour then press ENTER 12 The minute indication flashes Use the same procedure above to set the minutes OFF TIME appears and the hour indication flashes 5 Use the same procedure in step 4 to set the time to stop playback 6 Select the sound source Press 20 repeatedly to select iPod or TUNER then press ENTER 12 The display shows the timer settings
10. AIR SW10Ti system Subwoofer Subwoofer ID A ID A Teo a gO BES oN LN ms Not Pairing connected E I Paa aak FRR Main unit Main unit 1 Place the main unit near the subwoofer 2 Check that the power of the main unit and the subwoofer is turned on 3 Check that the S AIR ID of the main unit is the same as the S AIR ID of the subwoofer 4 Perform the pairing operation of the main unit and the subwoofer as follows Main unit Press SYSTEM MENU 18 Press 20 repeatedly until S AIR appears then press ENTER 12 Press 20 repeatedly until PAIRING appears then press ENTER 12 OK flashes Press ENTER 12 again PAIRING flashes and the main unit is ready for pairing with the subwoofer Subwoofer Press PAIRING 11 on the rear panel of the subwoofer using a pointed object When pairing is performed COMPLETE is displayed on the main unit for 2 seconds and the PAIRING indicator 11 on the subwoofer lights up To cancel pairing Change the S AIR IDs of the main unit and the subwoofer to different S AIR IDs To stop the pairing operation midway It takes a few seconds to complete the pairing of the main unit and subwoofer after pressing PAIRING 11 on the rear panel of the subwoofer in step 4 You can undo the pairing setting before c
11. Press BASS BOOST 23 repeatedly to select ON or OFF The default setting is OFF PRESET EQ You can select the sound effect Press EQ 22 repeatedly to select FLAT ROCK POP or JAZZ The default setting is ROCK SUBWOOFER LEVEL You can adjust the subwoofer s level Press SUBWOOFER LEVEL 13 repeatedly to switch the level 3 6dB 2 4dB 1 2dB 0 OdB 1 2dB 2 40B 3 6dB The default setting is 1 Turning off the beep sound When you press a touch sensitive button a beep sounds The following steps show you how to disable the beep Press SYSTEM MENU 18 2 Press 20 repeatedly until SYSTEM appears then press ENTER 12 3 Press 20 repeatedly until BEEP appears then press ENTER 12 4 Press 20 to select OFF then press ENTER 12 When you enable the beep select ON in step 4 Hy Changing the display You can change the information in the display While the main unit is on Press DISPLAY 19 Each time you press the button the display changes as follows Frequency gt Clock When an optional sub unit is connected to the unit the sub unit can display the same information except for the clock While the main unit is off The clock is displayed You can
12. SONY Wireless Audio System Operating Instructions AIR SW10Ti S AIR DIGITAL WIRELESS 2009 Sony Corporation To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture Printed in China To reduce the risk of fire do not cover the ventilation opening of the apparatus with newspapers tablecloths curtains etc Do not place the naked flame sources such as lighted candles on the apparatus To reduce the risk of fire or electric shock do not expose this apparatus to dripping or splashing and do not place objects filled with liquids such as vases on the apparatus As the main plug is used to disconnect the unit from the mains connect the unit to an easily accessible AC outlet Should you notice an abnormality in the unit disconnect the main plug from the AC outlet immediately The unit is not disconnected from the mains as long as it is connected to the AC outlet even if the unit itself has been turned off Do not install the appliance in a confined space such as a bookcase or built in cabinet Do not expose batteries or apparatus with battery installed to excessive heat such as sunshine fire or the like The nameplate is located on the bottom exterior of the main unit ATS SW10Ti Notice for the customers in the U S A This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of
13. To resume playback press PAI 6 again Selecta menu or 4 PO You can scroll up or down track for the iPod iPhone menus playback Skip a track Haa gt r 7 Find a pointina Hold down Ke PPI 7 during track playback and release the button at the desired point Choose the selected item ENTER 12 You can choose the selected item much like the center button on the iPod Return to the previous menu iPod MENU RETURN 21 You can return to the previous menu much like the Menu button on the iPod iPhone To use the unit as a battery charger You can use the main unit as a battery charger for the iPod iPhone Charging begins when the iPod iPhone is placed on the iPod iPhone connector The charging status appears on the iPod iPhone display For details refer to the user s guide of your iPod iPhone To stop charging the iPod iPhone Remove the iPod iPhone Notes While playing the tuner in the PARTY mode you cannot operate the iPod iPhone When placing or removing the iPod iPhone handle the iPod iPhone in the same angle as that of the iPod iPhone connector on the system and do not twist or sway the iPod iPhone to prevent connector damage Do not carry the main unit with an iPod iPhone set on the connector Doing so may cause a malfunction When placing or removing the iPod iPhone brace the main unit with one hand and take care n
14. curely Tuner Severe hum or noise or stations cannot be received TUNED or ST flashes on the display Connect the antenna properly Find a location and an orientation that provide good reception and then set up the antenna again Keep the antenna away from the power cord to avoid picking up noise Connect a commercially available external antenna Turn off nearby electrical equipment To reset the main unit to factory settings If the main unit still does not operate properly reset the main unit to factory settings 1 Disconnect and reconnect the power cord then turn on the main unit Press SYSTEM MENU 18 Press 20 repeatedly until SYSTEM appears then press ENTER 12 N gt Press 20 repeatedly until RESET appears then press ENTER 12 RESET OK appears Press ENTER 12 again to confirm the setting wn All user configured settings such as preset radio stations timer and the clock are deleted To reset the subwoofer to factory settings If the subwoofer still does not operate properly reset the subwoofer to factory settings 1 Disconnect and reconnect the power cord then turn on the subwoofer N Press PAIRING 11 on the rear panel of the subwoofer and I 1 for 3 seconds on the subwoofer at the same time The pairing setting you configured is de
15. damage to the main unit and subwoofer Notes Make sure to turn off the main unit and the subwoofer when inserting or removing the supplied wireless transceivers EZW RT10A Failure to do so may result in damage to the main unit and subwoofer Do not touch the terminals of the supplied wireless transceivers EZW RT10A Do not insert any device other than the supplied wireless transceivers EZW RT10A into the EZW RT10A slot E FM antenna Find a location and an orientation that provide good reception and then set up the antenna Keep the antenna away from the power cord to avoid picking up noise Power Connect the power cord to a wall socket To use the iPod iPhone Insert a Universal Dock Adapter into the Dock 4 before use Use the supplied Universal Dock Adapter with the main unit for iPhone and iPhone 3G as follows The adapter number is shown on the bottom of Dock Adapter iPhone iPhone 3G When you use other iPod models use the adapter supplied with your iPod model or purchase a compatible Dock Adapter from Apple Inc To remove the Dock Adapter pull it up with your fingernail or a flat object using the slot inside the adapter Connector Dock Adapter To set the clock Use buttons on the remote to set the clock on the main unit 1 Press 1 1 to turn on the main unit 2 Select the cl
16. eo reception Presetting radio stations Use buttons on the remote to preset stations 1 Tune in the desired station 2 Press SYSTEM MENU 18 3 Press 20 repeatedly until TUNER appears then press ENTER 12 4 Press 20 repeatedly until MEMORY appears then press ENTER 12 TUNED ST PARTY Preset number 5 Press 20 repeatedly to select your desired preset number If another station is already assigned to the selected preset number that station is replaced by the new station 6 Press ENTER 12 Repeat steps 1 through 6 to store other stations You can preset up to 20 FM stations The preset stations are retained for about half a day even if you disconnect the power cord or if a power failure occurs To call up a preset radio station Press PRESET 24 repeatedly Adjusting the sound The main units DSP Digital Signal Processor system provides the following optional sound settings CROSSOVER You can set the frequency that is output by the subwoofer A lower setting value will provide deeper bass 1 Press SYSTEM MENU 18 2 Press 20 repeatedly until SOUND appears then press ENTER 12 3 Press 20 repeatedly until CROSSOVER appears then press ENTER 12 4 Press 20 to change the crossover frequency Hz from 80 100 120 140
17. er cord are connected and turn on the main unit and subwoofer There is no sound from the main unit Turn off the main unit and then turn it on again Check that the power cord is connected securely and the main unit is turned on Increase the volume of the main unit There is no sound from the subwoofer If you use another main unit place it more than 8 m away from the main unit Confirm the S AIR IDs of the main unit and the subwoofer Check the pairing setting Place the main unit and subwoofer closer together Stop using any equipment that generates electromagnetic energy such as a microwave oven Place the main unit and subwoofer away from other wireless devices Stop using any other wireless devices Change the S AIR ID settings of the main unit and the subwoofer Turn off the main unit and the subwoofer and then turn them on again Check that the power cord is connected securely and the main unit and subwoofer are turned on Increase the volume of the main unit Change the RF CHANGE setting on the main unit The subwoofer does not work effectively for music without lower frequencies There is no sound from an optional sub unit For details on the sub unit refer to the Operating Instructions supplied with the sub unit There is noise or sound skips If you use another main unit place it more than 8 m away from the main unit Place the main unit and
18. ergy AIR SW10Ti is an S AIR compatible packaged product that consists of one S AIR main unit and one subwoofer bracket or table specified by the You can enjoy high quality sound by connecting the manufacturer or sold with the subwoofer wirelessly The subwoofer can be used only apparatus When a cart is used use AA with this main unit caution when moving the cart In addition connecting the S AIR main unit hereafter app Aratus combination to avoid injury called main unit to optional S AIR sub units hereafter from tip over TEN called sub units using S AIR technology you can use each unit in a remote location For example you can install optional sub units one in a study room and the other in a bedroom and install the system in the living room You can then listen to music from the system located in the living room by controlling the sub units Up to 10 optional sub units can be connected to a main unit manufacturer unused for long periods of time Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped S AIR Sony Audio Interactive Radio frequency Recent times have seen the rapid spread of DVD media Digital Broadcasting and other high quality media To e
19. leted Messages CANCEL Time out without pairing COMPLETE Pairing is completed PAIRING Pairing is in progress TIME NG The Play Timer start and end times are set to the same time Notes on use of the S AIR product As the S AIR product transmits sound by radio waves sound may skip if radio waves are obstructed This is a characteristic of radio waves and is not a malfunction of the system As the S AIR product transmits sound by radio waves equipment that generates electromagnetic energy such as a microwave oven may interfere with sound transmission of the system As the S AIR product uses the radio waves that share the same frequency as other wireless systems such as wireless LAN or Bluetooth devices interference or poor transmission may result In this case take the following steps Do not install S AIR products near other wireless systems Do not use S AIR products and other wireless systems at the same time The transmission distance differs depending on the usage environment Find a location where transmission between the unit and subwoofer is most effective and install the unit and subwoofer there On safety Completely disconnect the power cord from the wall socket if the main unit and subwoofer are not going to be used for an extended period of time When unplugging them always grip the plug Never pull the cord itself Should any solid object or liquid get into the main unit
20. nsure that the subtle nuances of these high quality media are transmitted with no deterioration Sony has developed a technology called S AIR for the radio transmission of digital audio signals with no compression and has incorporated this technology into the EZW RT10A This technology transfers digital audio signals with no compression using the 2 4 GHz band range of ISM band Industrial Scientific and Medical band such as wireless LANs and Bluetooth applications and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Main unit ATS SW10Ti Wireless Audio Transmitter Touch sensitive buttons Operation using the touch sensitive button that beeps Subwoofer SA WA10R
21. ock set mode Press CLOCK TIMER 16 to select the clock set mode If PLAY SET flashes press 20 repeatedly to select CLOCK and then press ENTER 12 3 Set the time Press 20 repeatedly to set the hour then press ENTER 12 Use the same procedure to set the minutes When you turn off the unit the clock display appears in the display Note The clock settings are lost when you disconnect the power cord or if a power failure occurs To adjust the volume Press VOLUME 8 Establishing the S AIR connection You can easily establish the connection by setting the same S AIR ID for the main unit and the subwoofer 1 Check that the wireless transceivers are inserted securely in the main unit and the subwoofer 2 Press 1 1 on the main unit and the subwoofer to turn them on 3 Set the same S AIR ID for the main unit and the subwoofer as follows Main unit Press SYSTEM MENU 18 Press 20 repeatedly until S AIR appears then press ENTER 12 Press 20 repeatedly until S AIR ID appears then press ENTER 12 Press 20 repeatedly to select A B or C then press ENTER 12 Subwoofer Set the S AIR ID selector 10 on the rear panel to the same S AIR ID as the main unit Tip The S AIR ID is
22. ompleting the pairing If you have done the pairing operation of only the main unit repeat to of step 4 again If you have done the pairing operation of both the main unit and subwoofer repeat Q to of step 4 and press PAIRING 11 on the rear panel of the subwoofer Tip You can also pair the main unit with optional sub units For details on turning on the pairing function refer to the Operating Instructions supplied with the sub unit If the S AIR connection is unstable Since the S AIR product uses radio waves that share the same frequency 2 4 GHz as other wireless systems such as wireless LAN or Bluetooth devices interference or poor transmission may result if you use other wireless devices near the system In this case the connection may be improved by changing the RF CHANGE Radio Frequency Change setting on the main unit 1 Press SYSTEM MENU 18 2 Press 20 repeatedly until S AIR appears then press ENTER 12 3 Press 20 repeatedly until RF CHANGE appears then press ENTER 12 4 Press 20 repeatedly to select the desired setting The default setting is underlined AUTO Normally select this setting The main unit changes the RF CHANGE setting to ON or OFF automatically ON The main unit transmits sound by searching for the best channel for transmission OFF The main uni
23. or a subwoofer unplug the unit in question and have it checked by qualified personnel before operating it again The power cord should only be changed by a qualified service facility On placement Do not place the unit and subwoofer in an inclined position or in locations that are extremely hot cold dusty dirty or humid or lacking adequate ventilation Also do not place in a location subject to vibration direct sunlight or bright light Be careful when placing the unit and the subwoofer on surfaces that have been specially treated for example with wax oil polish as staining or discoloration of the surface may result On heat buildup Heat buildup of the unit and subwoofer during operation is normal and no cause for alarm Cleaning the cabinet Clean the cabinet with a soft dry cloth Do not use any type of abrasive pad scouring powder or solvent such as thinner benzine or alcohol Main unit ATS SW10Ti Wireless Audio Transmitter AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION The United States model only With 8 ohm loads both channels driven from 200 15 000 Hz rated 5 watts per channel minimum RMS power with no more than 10 total harmonic distortion from 200 milliwatts to rated output Amplifier section DIN power output rated 5 5 watts 8 ohms at 1 kHz DIN Continuous RMS power output reference 5 5 watts 8 ohms at 1 kHz 10 THD Wireless
24. ot to press the controls of the iPod iPhone by mistake Before disconnecting the iPod iPhone pause playback The volume level of the main unit does not change even if adjusted on the iPod iPhone The main unit is designed for iPod iPhone only You cannot connect any other portable audio players Depending on the iPod iPhone model you are using and its status operations using the main unit may not be accepted or the wrong operations may be performed Sony cannot accept responsibility in the event that data recorded to an iPod iPhone is lost or damaged when using the iPod iPhone with this S AIR product Listening to the radio 1 Select FM Press FUNCTION repeatedly or TUNER on the unit 5 2 Perform tuning For automatic tuning Press and hold TUNING 7 until the frequency indication changes and then release AUTO lights up Scanning stops automatically when a station is tuned in and then TUNED and ST for FM stereo programs only appear TUNED ST PARTY When tuning in an FM station if TUNED does not appear and the scanning does not stop press TUNING 7 repeatedly to tune in the desired station For manual tuning Press TUNING 7 repeatedly to tune in the desired station Tip To reduce static noise on a weak FM stereo station press FM MODE 14 repeatedly until MONO appears to turn off ster
25. r nearest Sony dealer General The remote does not function Remove any obstacles between the remote and the remote sensor and position the unit away from fluorescent lights Point the remote at the remote sensor 3 Move the remote closer to the unit The S AIR indicator 9 on the main unit does not light up and the S AIR indicator 9 on the subwoofer flashes Check that the power cords are connected securely and the main unit and the subwoofer are turned on Check that the supplied wireless transceivers are inserted securely in the main unit and subwoofer Connecting the main unit and the subwoofer is not possible The S AIR indicator 9 on the main unit is turned off and or the S AIR indicator 9 on the subwoofer flashes Check that the supplied wireless transceivers are inserted securely in the main unit and subwoofer If you use another S AIR unit place it more than 8 m away from the main unit Confirm the S AIR IDs of the main unit and subwoofer The main unit is paired with another subwoofer Pair the main unit with the subwoofer you are using The main unit is paired with another subwoofer Cancel pairing Place the main unit and subwoofer away from other wireless devices Stop using any other wireless devices The main unit or the subwoofer is turned off Make sure the pow
26. r the wireless transceiver EZW RT10A This Class B digital apparatus complies with Canadian ICES 003 Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device http Awww sony net This equipment complies with IC radiation exposure limits set forth for uncontrolled equipment and meets the RSS 102 of the IC radio frequency RF Exposure rules This equipment should be installed and operated with at least 20 cm and more between the radiator and person s 1 Read these instructions body excluding extremities hands wrists feet and 2 Keep these instructions ankles 3 Heed all warnings 4 Follow all instructions e 5 Do not use this apparatus near water License and Trademark Notice 6 Clean only with dry cloth S AIR and its logo are trademarks of Sony Corporation 7 Do not block any ventilation openings Install in iPod isa trademark of Apple Inc registered in the US accordance with the manufacturer s instructions k EE other FOR kof Apple I 8 Do not install near any heat sources such as radiators Tk on sa ae nr k PPan me dbyth heat registers stoves or other apparatus including E Biuetooth Word MALK And togosare owned by the amplifiers that produce heat Bluetooth SIG Inc and any use of such marks by Sony 9 D Ra ot defeat fs safety purpo se
27. sufficient magnitude to constitute a risk of electric shock to persons This symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance The following indications are located on the bottom exterior of the main unit ATS SW10Ti RISK OF ELECTRIC SHOCK DO NOT OPEN H Owner s Record The model and serial numbers of the main unit are located on the bottom of the main unit and those of the subwoofer are located at the rear of the subwoofer Record these numbers in the space provided below Refer to them whenever you call upon your Sony dealer regarding this product Model No Serial No Important Safety Instructions CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment 4 125 804 11 1 For the wireless transceiver EZW RT10A This equipment must not be co located or operated in conjunction with any other antenna or transmitter This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency RF Exposure Guidelines in Supplement C to OET65 This equipment should be installed and operated with at least 20cm and more between the radiator and person s body excluding extremities hands wrists feet and ankles Notice for the customers in Canada Fo
28. t 60 Hz 10 THD Wireless transceiver EZW RT10A Communication System S AIR Specification version 1 0 Frequency band 2 4000 GHz 2 4835 GHz Modulation method DSSS Power requirements DC 3 3 V 350 mA Dimensions w h d 50 x 13 x 60 mm Mass 24g Speaker Speaker system Woofer 100 mm cone type bass reflex Rated impedance 6 ohms General Power requirements 120V AC 60Hz Power consumption 17 watts Dimensions w h d Approx 123 x 282 x 375 mm Mass Approx 4 3 kg Supplies accessories Wireless transceiver EZW RT10A 2 Remote commander RM ANU066 1 R03 size AAA batteries 2 FM lead antenna 1 Universal Dock Adapters for iPhone 2 Design and specifications are subject to change without notice Halogenated flame retardants are not used in the certain printed wiring boards
29. t transmits sound using a fixed channel for transmission When you select this setting select the S AIR ID that provides the best connection 5 Press ENTER 12 to exit the system menu Turning the subwoofer on off in sync with the main unit When the subwoofer is on or in power save mode press 1 T on the main unit to begin using the system By pressing I T on the main unit to turn it off the subwoofer will enter power save mode Each time you press I T on the main unit the subwoofer will be turned on off in sync with the main unit You can check the power status of the subwoofer by the 1 indicator 2 on the subwoofer Subwoofer status indication indicator Status Green Power on Orange Power save mode You can turn on the subwoofer by pressing I T on the main unit Red Standby mode You cannot turn on the subwoofer by pressing I T on the main unit To turn on the subwoofer press I T on the subwoofer Playing the iPod iPhone 1 Select the iPod function Press FUNCTION repeatedly or iPod on the unit 5 2 Place the iPod iPhone on the iPod iPhone connector L 3 Start playback Press Pll 6 To control the iPod iPhone You can control your iPod iPhone with the following buttons on the main unit To Press Pause playback PG
30. transceiver EZW RT10A Communication System S AIR Specification version 1 0 Frequency band 2 4000 GHz 2 4835 GHz Modulation method DSSS Power requirements DC 3 3 V 350 mA Dimensions w h d 50 x 13 x 60 mm Mass 24g Tuner section FM stereo FM superheterodyne tuner Tuning range 87 5 108MHz 100kHz step Antenna FM lead antenna Antenna terminals 75 ohms unbalanced Intermediate frequency 10 7 MHz Speaker section Speaker system Full range 60 mm cone type Rated impedance 8 ohms iPod iPhone section Compatible iPod iPhone models iPod nano iPod touch 4th generation iPhone 3G 2nd generation video iPod nano 3rd generation iPod touch video iPod classic lst generation iPod nano iPhone 2nd generation iPod aluminum 5th generation video iPod nano 1st generation iPod iPod 4th generation 4th generation color display iPod mini General Power requirements 120V AC 60Hz Power consumption 15 watts Dimensions w h d Approx 310 x 121 x 162 mm Mass Approx 1 7 kg Subwoofer SA WA10R Wireless Speaker System AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION The United States model only With 6 ohm loads from 50 120 Hz rated 50 watts minimum RMS power with no more than 10 total harmonic distortion Amplifier section DIN power output rated 40 watts 6 ohms at 60 Hz DIN Continuous RMS power output reference 50 watts 6 ohms a
Download Pdf Manuals
Related Search