PYLE Audio PT-669D Cassette Player User Manual
Contents
1. 2 MADE IN CHINA2. Panel Information COUNTER ONSTANDEY DECK A PLAYBACK naa ti REC CrO2 REC PLAYBACK BECK B Saree oe a ena memes SAE St gt lt lt gt gt m 2 u dam 5 r e 1 ON STANDBY SWITCH Press button to switch ON the unit and press again to switch OFF unit into STANDBY MODE If the unit is left unattended for long period remove the plug from the power socket 2 CASSETTE HOLDER 3 PEAK LEVEL INDICATOR These indicate the recording level during recording and output level during playback The LED indication varies with the signal strength during recording and playback HIGH SPEED This lights when in the high speed dubbing DYNAMIC NR When you need the Dynamic noise reduction push the level switch to the left PLAY CrO2 METAL This lights when the CrO2 metal function is operated REC CrO2 This lights when CrO2 function is operated 4 TAPE COUNTER AND RESET BUTTON DECK B When recording or playing you can use the tape counter to count the tape length 5 REC LEVEL SWITCH Adjust the record level 6 CASSETTE OPERATION BUTTONS REC This lights when deck B is in the recording the record pause mode 0O 09 pla
3. since this may result in deterioration in performance of malfunction intended to alert the user to the presence of important Locations exposed to direct sunlight or near objects radiating operating and maintenance servicing instructions in the heat such as heating appliances literature accompanying the appliance ll Locations exposed to moisture or humidity ld Locations with poor ventilation exposed to dust and dirt WARMING To prevent fire or shock hazard do not expose this Locations which are unstable and not perfectly flat or which are appliance to rain or moisture susceptible to vibration Do not wipe with thinners Power plug When disconnecting the power cord from the power outlet always take hold of the plug and not the wire and pull free Never connect or disconnect the power plug with wet hands since you may receive an electric shock Remember to disconnect the power plug from the power outlet when you do not intend to use the unit for a prolonged period of time Wipe the panels and case from time to time with a soft cloth Using any kind of thinner alcohol or volatile liquid will mar the surface cause blotching on the exterior and erase the markings and should therefore be avoided Do not use insecticide sprays in the vicinity Dripping warning The product shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the product
4. LAY button Adjust the Amplifier Volume and Graphid Equalizer controls for your desired sound level and taste Press the STOP EJECT button to stop playback at any time Fast forward and rewind Deck A or Deck B For fast winding or rewinding the tape press the FFWD or REW button Press the STOP EJECT button when the desired location has been reached When the end of the tape has been reached the FFWD or REW button will be released automatically Pause DECK A or Deck B Press the PAUSE button to momentarily stop tape travel during playback or recording Re press the button for pause release and playback or recording tape re start Full automatic stop Deck A or Deck B Press the STOP EJECT button to stop playback or recording at any time When the end of the tape has been reached any of the PLAY REC REW or FFED buttons if pressed will be automatically released and the head block completely separates from the tape and capstan This protects tape and prevents pinch roller wearing out Recording Deck B When recording use the Deck B Operating Procedures Manually level control recording This unit has record level volume to adjust the record level Usually the volume has a center click When it reaches the center click position the tape can be recorded normally If the sound source signal is too strong a red spot will be appeared in the record level indicator You can adjust the record level volume to left position and vi
5. PYLE gt PRO MECHANICAL DECK PT 669D Ce Precautions Thank you for purchasing this product Taking time to read these operating instructions carefully before use will acquaint you fully amp with all its features and help ensure optimum performance In order to simplify the explanation illustrations may sometimes differ from the originals CAUTION DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lighting flash with arrowhead symbol within an equilateral is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is Do not remove the case and bottom panel Any inspections or adjustments inside the unit may lead to malfunctions and electric shocks Do not touch any of the inside parts Do not block the ventilation holes Do not block the ventilation holes on the top of the unit by placing records or other objects over them This will increase the inside temperature may lead to a failure or malfunction Installation precautions Do not install the unit in any of the following locations
6. ce versa In normal state the sound source level is between the red and green spots that s OdB 1 Press the STOP EJECT button and insert a cassette 2 When CrO2 tape is used for recording press the REC CrO2 switch 3 Press the record button The level meter at the peak level indicator will shift and the REC light will be lit up indicating t hat recording is underway 4 Press the STOP EJECT button to stop recording at any time Pause Press the PAUSE button to momentarily stop tape travel during recording Re press the button to pause release and recording restart Dubbing operation Deck A Deck B This unit enables you to dub a recorded tape to another tape by using the built in double deck mechanisms It is performed only one way from the Deck A to Deck B Preparation 1 Insert a cassette for playback in DECK A Select tape DIRECTION button FFWD or REW for the desired location of the tape to the beginning Insert a cassette into DECK B Select the dubbing speed by the dubbing High speed switch There are two dubbing speeds High speed and Normal speed High speed doubles Normal speed For high speed dubbing press High speed switch the light in the indicator will be lit up and the high speed dubbing is then activated Normal speed dubbing requires no pressing of the High speed switch and no light will be shown at the indicator at all Press the PAUSE button of DECK A Then press the PLAY button of DECK A Press t
7. he RECORD button of DECK B Oy a ae te Rh Rh Press the PAUSE button again of DECK A to release the pause mode The unit will start the synchronized dubbing operation To stop dubbing operation press the STOP EJECT button of DECK B N Note Do not change dubbing speed during dubbing operation Specifications Type Track system Tape speed Stereo double cassette deck 4 track 2 channel 4 8 cm sec Frequency response 20dB recording Chrome tape Normal tape 0dB recording Chrome tape Normal tape S N ratio Wow and flutter Crosstalk Harmonic distortion Channel separation Head 40 15 000Hz 3dB 40 14 000 Hz 3dB 40 8 000 Hz 3dB 40 8 000 Hz 3dB 58dB lt 0 2 DN 45500 40dB 1KHz Less than 1 at 1KHz OVU 3 rd H D Normal tape 40dB 1KHz Deck A for Auto playback Motors Fast Forward Rewind time Input terminals LINE IN x 2 Output terminals LINE OUT x 2 Power requirement For U K For U S A 8 Canada Power consumption Dimensions Weight ACCESSORIES Deck B for recording playback 2 gap ferrite head for erasure Design and specifications are subject to change without notice DC servo motor x 2 Approx 100 Sec with C 60 cassette Min input level 80mV Input impedance 50kQ Output 600mV 0dB Output impedance 5kQ AC 220V 50Hz 240V 50Hz 110V 60Hz 10W 420mm x 130mm x 220mm WxHxD 4Kg 8 5lbs Pin plug cord
8. y Press to play the tape rewind Press to rewind the tape mr fast forward Press to fast forward the tape m lt stop eject Press to stop the tape Pressing this button after the tape stops opens the cassette holder Hl pause Press to temporarily stop the tape in the record or playback mode Press it again to release the pause mode and restart the tape 7 REC CrO2 SWITCH For recording with CrO2 tape 8 HIGH SPEED DUBBING SWITCH When you need dubbing press this switch and the relative light will be lit 9 DUBBING SWITCH Press the DUBBING switch to get set for further record functions meanwhile relative light will be indicated 10 PLAY CrO2 METAL SWITCH Set these switches to NORM when using normal tape to CrO2 when using chrome tape and to METAL when using metal tape Operating Procedures o INTEGRATED CIRCUIT AC 220V 230V 50Hz REMOTE SYSTEM TO AMP od TAPE EQ CD LOGIC TAPE Be Les ea El ODODODOD IO ateo 0000 OOOOODO Playback a recorded tape DECK A or DECK B 1 2 3 4 5 Switch on the power of the unit Press the Stop Eject button and insert a recorded cassette tape For CrO2 metal tape further press the CrO2 metal switch and the light at the indicator will be lit up Press the P
Download Pdf Manuals
Related Search