Home

MTD 45 Snow Blower User Manual

1. D5200_0 INTRO 1 12 7 06 10 58 am ESPRIMO D5200 User s Manual Fujitsu endeavours to ensure that the information in this document is correct but accepts no liability for any error or omission Any procedures described in this document for operating Fujitsu products should be read and understood by the operator before such products are used To ensure that Fujitsu products function without risk to safety and health such procedures should be strictly observed by the operator The development of Fujitsu products and services is continuous and published information may notbe upto date Any particular issue of a product may contain facilities not described herein It is important to check the current position with Fujitsu Specifications and statements as to performance in this document are Fujitsu estimates intended for general guidance They may require adjustment in particular circumstances and should therefore not be taken as formal offers or commitments ESPRIMO is a trademark of Fujitsu Limited The following are registered trademarks of Microsoft Corporation MS MS DOS Windows NT Windows 98 Windows Millennium Window 2000 and Windows XP Intel and Pentium are registered trademarks of Intel Corporation in the U S Celeron is a registered trademark of Intel Corporation in the U S Other product names are trademarks or registered trademarks of respective companies Other products are copyrighted by individual companies All
2. Otherwise you might get burned gt ELECTRIC SHOCK When installing memory use Fujitsu s products Otherwise it might cause an electronic shock fire or failure gt A CAUTION 6 FAILURE When installing or removing memory do not remove screws other than those specified Removing the screws other than specified might cause injuries Doing so might also cause damage to your computer INJURY Do not touch the printed board other than areas specified Touching might cause injuries Doing so might also cause damage to your computer FAILURE Do not insert and remove memory repeatedly Doing so might cause damage to your computer 28 D5200_4 24 32 28 12 7 06 10 59 am i _ ae QO Locations for memory to be installed o LE TIT To install memory insert it into the memory slot of the main unit of the personal computer 1 Memory to be installed When installing additional memory use Fujitsu recommended parts only 6 Table of combinations of memory When installing memory check the following Table for the combination of the memory capacity and slots and install correctly DIMM1 DIMM2 Total capacity 256 MB 256 MB 256 MB 256 MB 512 MB 512 MB 512 MB 1 GB 1 GB 1GB 2 GB PG IMPORTANT 6 Do not install memory other than the combination in this Table D5200_4 24 32 29 1217106 29 10 59 am E I PS PP DON U In
3. Express slot and one PCI slot can be used 5 Antitheft lock Used to connect a commercially available antitheft cable POINT The antitheft lock supports Kensington Micro Saver Security System 14 D5200_2 11 19 14 12 7 06 10 59 am AP Ps PH T 6 Main switch Turn Off when completely turning off the power to the main unit of the computer The side is On and the O side is Off If itis set to Off the main unit of the personal computer is not powered on even when pressing the power supply button However if you do not use the computer for a long time set it to Off 7 Mouse port i Used to connect the mouse to the computer CH 8 Keyboard port Used to connect the keyboard to the computer 9 Monitor port Used to connect the monitor to the computer Analog RGB monitor cables can be used 10 Parallel port B Used to connect to a printer or scanner 11 Serial port Used to connect RS 232C support devices 12 LAN port Used to connect the LAN cable 13 USB ports Used to connect USB peripheral devices to your computer Complies with USB 2 0 14 Line in jack Q It is a sound input jack Used to connect to the output jack of audio devices 15 Line out jack Y It is a sound output jack Used to connect to the input jack of audio devices When connecting to a speaker use a terminal jack with the amplifier function built in it When the headphone is connected t
4. class 1 laser products in Subchapter J ofthe Federal Regulation DHHS 21 CFR of the United States Department of Health and Human Services Also it complies with the international standard IEC 60825 1 the CENELEC standard EN 60825 1 and the Japanese standard JIS C6802 which govern Class 1 laser products CAUTION Do not touch the on board battery Risk of electric shock burn and fire Do not replace the on board battery Risk of explosion if battery is replaced by incorrect type Please contact Fujitsu or the store where you purchased this products D5200_0 INTRO 3 12 7 06 10 58 am o LE TIT KE I PS PP DON Before Reading this Manual This section describes safety precautions and convention used in this manual Be sure to read this For Safe Operation This manual contains important information for using the ESPRIMO personal computer Read this manual thoroughly before using your PC In particular Safety Precautions in this manual must be read and understood Fujitsu a participant in the U S Environmental Protection Agency s EPA Energy Start Ja Program warrants that the computer meets the Energy Start specifications arr Using this Product for High Safety Applications This productis for office personal home ordinary industry and other general use Itis not designed and manufactured for use in high safety applications Do not use this product for such applications vvithout taking measures to
5. device If you pass on the device to third parties you should include this manual QO Energy saving When the PC is delivered some energy saving functions are already set 6 Ifyou are not using your PC switch it off Inthe BIOS Setup you may set further energy saving functions for the PC Depending on the operating system you can set additional power management features Energy saving under Windows XP The Screen Saver tab allows you to set energy saving functions for your screen Select the following item in the menu Start Settings Control Panel Display Display Properties gt Screen Saver Energy saving features of monitor With the default setting Control Panel Power Options Advanced additional power management features of Windows XP are available viii D5200_0 INTRO 8 12 7 06 10 58 am D5200_0 INTRO 9 12 7 06 10 58 am FCC Class B Compliance Statement The following statement applies to the products covered in this manual unless otherwise specified herein The statement for other products will appear in the accompanying documentation NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference Causing Equipment Regulations These limits are designed to provide reasonable protection against harmful interference in a residential installation
6. into the extension cord does not exceed the extension cord ampere rating Also make sure that the total rating of all products plugged into the wall outlet does not exceed 15 amperes Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points that could resultin a fire or electric shock Never spill liquid of any kind on the product Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage points or other risks Refer all servicing to qualified service personnel D5200_0 INTRO 2 12 7 06 10 58 am eo Lim TIT 13 14 15 16 17 Unplug this product from the vvall outlet and refer servicing to qualified service personnel under the follovving conditions a When the power cord or plug is damaged or frayed b If liquid has been spilled into the product c Ifthe product has been exposed to rain or water d Ifthe product does not operate normally when the operating instructions are followed Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition e Ifthe product has been dropped or the cabinet has been damaged f If the product exhibits a distinct change in performance indicating a need for service Use only t
7. medias Note Writing capability of the optical drive will depend on the optical drive that is bundled with the desktop 10 CD access indicator Lights up when data is being read from CD ROM DVD disc and when audio CDs are played 11 Foot For vertical positioning it serves to prevent the computer from falling The cables of the keyboard and the mouse can be collected through the slot of the foot 12 Floppy disk drive Used to write data to a floppy disk or to read data from a floppy disk 13 Floppy disk access indicator Lights up when data is being written to a floppy disk or when data is read from a floppy disk 14 Floppy disk eject button Pressed to eject a floppy disk Do not press this button when the floppy disk access indicator lights up Note Items 12 13 and 14 are applicable only for units bundled with Slim Optical or Slim Floppy Drive Combo 13 D5200_2 11 19 13 12 7 06 10 59 am 1 Power Outlet Used to connect the power cable to the monitor 2 Power Inlet Used to connect the power cable 3 Key hole for a padlock Install a commercially available key 4 Half Height expansion card slot Insert the expansion card to expand the functions of the personal computer Expansion cards that support one PCI
8. one above the other The PC can be used either horizontally or vertically We recommend that you place your equipment on a surface with good anti slip qualities In view of the multitude of different finishes and varnishes used on furniture it is possible that the rubber plastic feet of the devices will mark the surface they stand on E Installing the Feet POINT 6 6 The cables of the keyboard and the mouse can be collected through the slot of the foot The slot tor passing through the cable D5200_1 01 10 2 12 7 06 10 58 am e 00 CE II U Vertical positioning When this personal computer is vertically installed away from a wall install the feet with the following steps 1 Align the feet to the width of the main unit of the personal computer 2 Install the feet on the main unit of the personal computer Secure them in the screw holes on the back of the feet with screws D5200_1 01 10 3 12 7 06 10 58 am Q Horizontal positioning 1 Disassemble the foot D5200_1 01 10 4 12 7 06 10 58 am e 70 PS III POINT e For vertical installation the main unit of the personal computer can be installed by fitting the five rubbers attached to the four corners and center of the main unit of the personal computers When installing rubbers secure them in the positions where the foot does not touch when it is vertically installed Wipe dust off the location where rubbers for the m
9. satisfy the high safety requirements High safety applications require extremely high level of safety and involve serious hazards to life and health if the required safety is not assured High safety applications include the following 6 Nuclear reaction control in nuclear facilities automatic aviation control air traffic control mass transportation control life supporting medical equipment and missile launch control The computer includes limited life devices such as a CRT an LCD and a hard disk and if they are used continuously for an extended period of time it may become necessary to replace them earlier than expected The components come with one year warranty warranty periods may vary depending on the type of contract Besides the useful life the brightness of the LCD monitor decreases with the time for which itis used Backing Up the Data The customer is responsible for maintaining the integrity of data including the basic and application software stored or installed on the product We do not warrantthe integrity of data stored or installed onthe personal computer the customer sent for repair Take appropriate measures such as making a backup We assume no responsibility for loss of data and any direct or incidental damage due to any cause other than those specified in the warranty This computer is designed for use within the country If you are using it abroad please do so at your own respons
10. x 1000 x 1000 bytes With the calculation that 1 MB 1024 x 1024 bytes and 1 GB 1024 x 1024 x 1024 bytes the capacity actually displayed on Windows becomes less than the disk capacity described in this manual 3 There is no guarantee that your adapter can carry out communication normally with any other USB support peripheral devices When USB 1 1 compliance peripheral devices are connected they can be used by specifications for USB 1 1 The max rating of USB devices is 500mA per port Please see the manual with the USB devices 4 Toreduce energy consumption when powering off switch the main switch to the o side or unplug the power plug from the AC cable 5 The power consumption is for system only not including outlet devices 6 Values differ depending on the device configuration you use 7 Service Pack2 is applied at shipment POINT Note that for improvement specifications for this personal computer are subject to change 38 without notice D5200_5 33 39 38 12 7 06 11 00 am eo Lim TIT on 00 09 A l l T 39 D5200_5 33 39 39 12 7 06 11 00 am
11. Card POINT 6 Shutoff your computer after the initial Windows setup before proceeding to installing expansion card ZN WARNING ELECTRIC SHOCK A e Before installing or removing expansion cards turn off the computer and connected devices and unplug the computer Otherwise you might get an electric shock HIGH TEMPERATURE Before installing or removing expansion cards allow for sufficient times after turning off and unplugging the computer Otherwise you might get burned gt ELECTRIC SHOCK When installing expansion cards use Fujitsu s products Otherwise it might cause an electronic shock fire or failure gt A CAUTION 6 FAILURE When installing or removing expansion cards do not remove screws other than those specified Removing the screws other than specified might cause injuries Doing so might also cause damage to your computer INJURY Do not touch the printed board other than areas specified Touching might cause injuries Doing so might also cause damage to your computer INJURY Do not touch the metal fitting on the back side of the main unit of the personal computer of the mother board Touching might cause injuries Doing so might also cause damage to your computer 33 D5200_5 33 39 33 12 7 06 11 00 am E NO ee QO Locations for expansion cards to be installed To install an expansion card insert it into the expansion card slot of the main unit of the pe
12. I CAVI PRIMA DI RIMUOVERE SULL ALIMENTATORE RICHIEDERE ASSISTENZA DI PERSONALE TECNICO QUALIFICATO CUIDADO RIESGO DE CHOQUE EL CTRICO DESCONNECTAR EL CABLE DE AILMENTACION Y DEMAS CABLES ANTES DE DESMONTAR LA FUENTE ACCESO INTERNO SOLO AUTORIZADO A PERSONAL T CNICO CUALIFICADO CUIDADO RISCO DE CHOQUE EL CTRICO DESCONECTAR CABO DE FOR A E TODOS OS OTROS CABOS ANTES DE REMOVER A FONTE DEALIMENTA O PARM MANUTEN O ENCAMINHAR PARA PESSOAL TECNICO QUALIFICADO ZN WARNING Electric shock Before mounting or dismounting an optional unit in from your PC switch off the PC and all connected units Unplug all power cords from respective outlets to prevent electric shock and unplug all data communication cables from the respective outlets xii D5200_0 INTRO 12 27 7 06 10 02 am ET o Organization of This Manual Before Reading This Manual Chapter 1 Preparing for Use This chapter provides the names and functions of individual parts Chapter 2 Operation This section describes the location ofinstallation and installation ofthe computer Chapter 3 Troubleshooting and Tips This chapter provides the basic information on the PC and operation Chapter 4 System Expansion This chapter provides basic information on how to handle the peripherals installed or can be installed on the PC xiii D5200_0 INTRO 13 12 7 06 10 58 am e 700 PS III Contents CHAPTER 1 Prepari
13. This equipment generates uses and can radiate radio frequency energy and if not installed and used in strict accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 6 Reorient or relocate the receiving antenna Increase the separation between equipment and the receiver 6 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 6 Consult the dealer or an experienced radio TV technician for help Fujitsu is not responsible for any radio or television interference caused by unauthorised modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu The correction of interference caused by such unauthorised modification substitution or attachment will be the responsibility of the user The use of shielded I O cables is required when connecting this equipment to any and all optional peripheral or host devices Failure to do so may violate FCC rules eo E ITT iz o NO ME Q Transporting the PC A CAUTION Transport all parts separately in
14. ain unit of the personal computer are installed When moving the main unit of the personal computer after the rubbers have been installed do not drag the rubbers ci D5200_1 01 10 5 12 7 06 10 58 am E Connect the Monitor Mouse and Keyboard The ports for monitor mouse and keyboard are on the rear and on the front of the system unit Q Connecting the keyboard Connecting standard keyboard Use the supplied keyboard cable only 6 Plug the round keyboard cable connector into the port marked vvith this symbol on the system unit Q Connecting the mouse Connecting a PS 2 mouse Connect the PS 2 mouse to the PS 2 mouse port Connecting USB mouse 6 Connect the USB mouse to the USB port e on the system unit CH D5200_1 01 10 6 E T PS 2 keyboard port purple U PS 2 mouse port green _ Monitor port blue mr USB port black on the system unit 12 7 06 10 59 am I ao SHESESH E Initial Switch on Software will be Installed If the PC is connected to a network the network protocol is required as well as the user and server details Contact your network administrator if you have any questions about these settings When you switch on your PC for the first time the supplied software is installed and configured You should plan some time for this as this process must not be interrupted Z CAUTION Once the installation has been s
15. asswords Notational conventions The meanings of the symbols and fonts used in this manual are as follows ZN CAUTION Indicates information which is important for your health or for preventing physical damage Q Indicates important information which is required to use the system properly Text which follows this symbol describes activities that must be performed in the order shown Text in this typeface indicates screen outputs Quotation marks indicate names of chapters or terms D5200_0 INTRO vii 7 12 7 06 10 58 am I gj SEE IN Important Notes Inthis chapter you will find information regarding safety which is essential to take note of when working with your PC The manufacturer s notes contain helpful information on your PC Q Safety Z CAUTION During installation and before operating the device please observe the instructions on environmental conditions in the chapter entitled Technical data as well as the instructions in the chapter Preparing for Use Please check whether the device is correctly set for the local power supply see Preparing for Use chapter The main switch and the ON OFF switch do not disconnect the system unit from the mains voltage To completely disconnect the mains voltage remove the power plug from the grounded mains outlet Caution components in the system can get very hot Q Manufacturer s notes Keep this operating manual together with your
16. ctly could result in damage to your computer or peripheral devices Precautions Take the following precautions when installing peripheral devices 6 ltis recommended to use Fujitsu s products when installing peripheral devices Note that the warranty does not cover abnormal performance or failures of the computer caused by installing CD or DVD other than Fujitsu s products For devices that are not prepared by Fujitsu inquire the manufacture of peripheral devices you use about whether your computer supports these devices Your computer supports performances of Fujitsu s products only Install one peripheral device only at one time Installing two or more peripheral devices at one time may cause failures of normal installation of drivers etc Complete the installation of one peripheral device before installing another peripheral device Turning off the power to the computer and the devices connected For safety be sure to unplug the computer Currents still flow inside the computer even after turning off your computer Do not work on the computer immediately after turning off the computer 6 Donot work on the computer immediately after turning off the computer Internal devices of the computer become hot immediately after the computer has been turned off Turn off the power to unplug the computer and wait 10 minutes or so before start working 25 D5200_4 24 32 25 12 7 06 10 59 am i _ ae 26 Do not disassemble
17. ductors on it please take care when you insert or remove boards Make sure expansion boards are inserted straightly Never use sharp objects screwdrivers for leverage shown Boards with electrostatic sensitive devices ESD are identifiable by the label bh When you handle boards fitted with ESDs you must under all circumstances observe the following points A You must statically discharge yourself before working with boards e g by touching a grounded object The equipment and tools you use must be free of static charges Pull out the power plug before inserting or removing boards Always hold boards with ESDs by their edges Never touch pins or conductors on boards fitted with ESDs 24 D5200_4 24 32 24 12 7 06 10 59 am on 00 6 CE l l E Before Connecting Peripheral Devices Your computer can be expanded by connecting or incorporating various peripheral devices ZN WARNING ELECTRIC SHOCK A 6 When connecting peripheral devices to your computer do not connect devices other than Fujitsu recommended products Doing so could result in an electronic shock fire or failure CAUTION FAILURE 6 When installing or removing peripheral devices do not remove screws other than those specified in the manual Removing the screws other than those specified may cause injuries to persons and damage to the devices FAILURE QO 6 Follow the instructions in this manual to connect the cables Connecting the cables incorre
18. ection of the monitor mouse and keyboard to the system unit and the setup of the supplied software Q 6 External devices If you have received other devices in addition to your PC e g a printer or a modem do not connect these until after the initial installation e Drives and boards If you have received drives or boards with your PC please do not install them until after first time setup How to install drives and boards is described in the chapter System expansions Perform the following steps in the prescribed order 1 2 3 4 Decide where you are going to use the PC and then set it up Connect the monitor mouse and keyboard to the PC Check the rated voltage of the PC and connect it to the mains Switch on the PC and follow the instructions on the screen D5200_1 01 10 1 12 7 06 10 58 am TS I gj o SHESHIN E Setting Up the PC Z CAUTION When installing your PC give consideration to the recommendations and safety notes Set up the PC only in its correct orientation The points to observe are illustrated on the following pages Do not expose the PC to extreme environmental conditions and protect it from dust humidity and heat When installing the PC provide sufficient clearance around the PC as indicated in the Technical data chapter to ensure adequate ventilation In order to avoid overheating do not cover the ventilation area of the monitor or the PC Do not place several system units
19. eeeteeeeeeeeaees 22 The Floppy Disk Cannot be Read or Written aaa aauaana ananas anen vec 22 Time and or Date is not Correct aaa ua au auuaaa nana nana anen e enes eee zere v eee rere eren Error Messages on the Screen Restoring the Hard Disk Contents T S CHAPTER 4 System Expansion System EXPanSlOM Ssasns ses zer sdi s ae ey sasia vese se Information about Boards 00 0 cece nana nenes sene e serre vere sense sere se rras re venien eee Before Connecting Peripheral Devices Removing the Main Unit Cover 0 0 ce aaa nana nane anes enes eee eee eee vere e sere e re eee Installing MEMOFY des iivc situr veset i s desi ni b sh dv ss Installing the Expansion Card Electrical Data xiv D5200_0 INTRO 14 12 7 06 10 58 am SH 111 6 Chapter 1 Preparing for Use A CAUTION Please take note of the safety information in the Important notes chapter E Unpacking and Checking the Delivery It is recommended not to throw away the original packaging material It may be required for reshipment at some later date Unpack all the individual parts Check the delivery for damage incurred during transportation Check whether the delivery agrees with the details in the delivery note Should you discover that the delivery does not correspond to the delivery note notify your local sales outlet immediately Steps for Initial Setup First time setup includes the conn
20. exact description of how to connect external devices to the serial port please refer to the device documentation Settings of the serial port If you need to change the settings of the serial port e g address interrupt you can do so inthe BIOS Setup Device drivers The devices connected to the serial port require drivers Your operating system already includes many drivers Nevertheless if the driver you need is not on the hard disk please install it from the data carrier supplied with the device or with the application programme QO Connecting external devices to the parallel port External devices can be connected to the parallel port e g a printer Connect the data cable to the external device 6 Connect the data cable to the parallel port 24 For an exact description of how to connect external devices to the parallel port please see the device documentation Q 6 Settings of the parallel port If you need to change the settings of the parallel port e g address interrupt you can do so in the BIOS Setup Device drivers The devices connected to the parallel port require drivers Your operating system already includes many drivers Nevertheless if the driver you need is not on the hard disk please install it from the data carrier supplied with the device or with the application programme 10 D5200_1 01 10 10 12 7 06 10 59 am Chapter 2 Operation m Switching On the PC 6 If necessary
21. g programs or drivers important files may be overwritten and modified To be able to access the original data in the event of any problems following installation you should backup your hard disk prior to installation E Power on Indicator Remains Unlit after you have Switched on your Device This may be due to the following The mains voltage supply is faulty Check that the power cable is plugged properly into the system unit and grounded mains outlet Switch onthe PC Internal power supply overloaded Remove the PC s power plug from the grounded mains outlet Wait fora moment Plug the power cable into the grounded mains outlet again Switch on the PC 20 D5200_3 20 23 20 12 7 06 10 59 am Q The screen stays blank If your screen remains blank this may be due to the following Monitor is switched off Switch your monitor on Povver saving has been activated screen is blank Press any key on the keyboard or Deactivate the screen saver Enter the appropriate password Brightness control is set to dark Adjust the brightness control For detailed information please refer to the operating manual supplied with your monitor Power cable not connected Switch off the monitor and the PC Check that the monitor power cable of the monitor is properly connected to the monitor and depending on the connector to the PC or to the grounded mains outlet Check that the PC power cable is p
22. he Ctrl key in combination vvith another key Its function varies vvith each application 12 Application key This key has the same function as clicking the right mouse button Press this key to display the shortcut menu of the selected item 13 Enter key The Enter key is also referred to as the Return key Press this key to perform line feed or execute a command 14 Delete key Press the Delete key to delete a character Press this key together with Ctrl and Alt to reset the computer 15 End key Press the End key to move the cursor all at once to the end of the current line or text 16 Cursor keys Press each of these keys to move the cursor in the desired direction 17 Page Down key Scrolls down the on screen page when pressed 18 Page Up key Scrolls up the on screen page when pressed 19 Numeric keypad Enables you to enter numerals when the Num Lock indicator is on The function described in the lower part of the numeric key is enabled when the Num Lock indicator is off 20 Num Lock key Press the Num Lock key to change the Ten key pad functions Point To tilt the keyboard pull up the tilt foot on the both sides of the underside of the keyboard Tilt foot I 17 D5200_2 11 19 17 12 7 06 10 59 am zz Ps A m Floppy Disks Note Applicable only for units bundled with Slim Optical or Slim Floppy Drive Combo Q Working with Floppy Disks Follow the instructions supplied by the vendo
23. he PC cannot be switched off with the ON OFF switch Cause The PC was not switched on with the ON OFF switch Press the ON OFF switch again Cause System crash Press and hold the ON OFF switch for at least four seconds until the PC switches off Out of system resources If you have too many applications running at once you may experience problems due to a lack of system resources In this case you should close unnecessary applications or e D5200 3 20 23 run the applications in a different order 23 23 1217106 10 59 am Chapter 4 System Expansion A CAUTION It may be necessary to update the BIOS when carrying out a system expansion or hardware upgrade When installing components that heats up easily make sure that the maximum permissible temperatures of the individual components are not exceeded The PC must be switched off when installing removing the system expansions and may not be in the energy saving mode This chapter describes all the activities required to modify your PC hardware e g installing boards or drives Read the supplied documentation before installing new drives and or boards Refer to the technical manual for the mainboard before making any extensions to the mainboard E Information about Boards Take care with the locking mechanisms catches and centring pins when you are replacing board or components on board To prevent damage to the board or the components and con
24. he proper type of power supply cord set provided in your accessories box for this unit It should be a detachable type UL listed CSA certified BS1363 ASTA SS145 certified rated 10A 250V minimum VDE approved or its equivalent Maximum length is 15 feet 4 6 meters If your computer includes a modem the cable used with the modem should be manufactured with a minimum wire size of 26 American wire gauge AWG and certified as the law in your respective country For detailed information please contact Fujitsu or the store where you purchased these products Please take extra precaution when connecting the LAN and do not connect the cables to the peripheral device s connector that might have excessive voltage CAUTION e Ifthe CD DVD drive is not operated correctly according to the instructions or procedures specified in the operating manual it may emit a laser beam Disassembling the CD DVD drive may cause you to be exposed toa harmful laser beam So never disassemble it The CD DVD drive may emit a Class 3A or Class 3B laser beam when its cover is detached The CD DVD drive may emit a Class 3A or Class 3B laser beam when its cover is detached Do not look at the laser beam directly or through an optical device Also be careful not to be exposed to the laser beam Safety of Laser Products The CD DVD drive installed on your computer uses a laser Class 1 Laser Products The CD DVD drive complies with the provisions pertinent to
25. ibility This equipment may be adversely affected by the momentary drop of the supplied voltage due to lightning Use of an uninterrupted AC power supply is recommended for measures against the momentary drop of the supplied voltage This message is based on the Japan Electronics and Information Technology Industries Association s guidelines for measures against momentary voltage drop in PCs Since this equipment contains special materials controlled by the Foreign Exchange and Foreign Trade Control Law Authorization under the law may be required to export this equipment iv D5200_0 INTRO 4 12 7 06 10 58 am o EE T Microsoft Service Pack Microsoft Corp offers Service Pack to provide the users of Microsoft Windows with more stable system operation http www microsoft com The latest version of the Service Pack helps you configure the most stable system using Microsoft Windows provided at that time by Microsoft Corp We recommend you to use the latest version Insome environments however the Service Pack may cause unexpected failure Read Readme txt for the Service Pack before use Again we recommend you to make a system backup in case of failed installation Components of this product motherboard CD ROM hard disk and floppy disk drive contain traces of heavy metals lead and chrome and chemical antimony Software License Agreement Fujitsu Limited Fujit
26. ng for Use Preparing for U SO asi s ess s z eper ves shte cccuscae sa uescctesicesseceedses sert Unpacking and Checking the Delivery s Steps for Initial Setup cati sis kat sdahis verdh ccs ev tye k s aE a arenen ohet eds aE RANTRE Sn Installing the Feet n se Connect the Monitor Mouse and Keyboard Initial Switch on Software will be Installed z Connecting External Devices 000 ee anon nana ana ne ee eneve e vere nr eee ren re eee eee eee rene eee CHAPTER 2 Operation KT cetcnssudeesascsdevacceessancessadeesssansussuscuevsaconesass Switching On the PC Switching Off the PC sci vese ori an vedi nie iink edin sode d r Front Panels of the Main Unit of the Personal Computer sses 12 Back Panel of the Main Unit of the Personal Computer sesers 14 KOYDOANO rarius iriiritia daiane viens th ur s th 16 Folppy DISKS tas se das sees ecsthase ieiuno eara tria en n r sh avant 18 Settings in BIOS Setup is ae dron h s nde vdiste ead dh s r das ed n dh nd r 18 Anti theft Protection and Lead Sealling sauna aa aan aaa nenes ene eee ene e veren 19 How to Lock the Main Unit of the Personal Computer From Behind 19 CHAPTER 3 Troubleshooting and Tips Troubleshooting and Tips Installing New Software Power on Indicator Remains Unlit after you have Switched on your Device 20 No Mouse Pointer Displayed on the Screen eeeceeeeeeseeeeeeeeee
27. ntrol systems air traffic control systems mass transportation operation and control systems life support systems and missile launchers in military facilities Keep the accompanying CD ROMs in a safe place The CD ROMs are needed to return the software installed on your computer to its initial state state at the time of purchase Temperature and humidity condition The computer should be used and stored under the following temperature and humidity conditions 10 to 35 C 20 to 80 RH during operation or 10 to 60 C 20 to 80 RH during storage no condensation during operation storage vi D5200_0 INTRO 6 12 7 06 10 58 am o EE T Conventions Used in this Manual Introduction This manual tells you how to put your PC into operation and how to operate it in daily use Depending on the configuration level chosen some of the hardware components described may not be available on your PC Please observe the notes on your operating system You can incorporate operable drives for example DAT drive as well as other boards Depending on the configuration selected the operating system is preinstalled on your hard disk e g Windows XP Your PC has a number of security features to ensure that no unauthorised persons can access your data for example you can activate a screen saver with password protection The security functions in the BIOS Setup also allow you to protect your data by means of p
28. o the headphone jack sound does not come out from the line out jack of the main unit of the personal computer 15 D5200_2 11 19 15 12 7 06 10 59 am Keyboard 1 A 16 9 10 11 12 1314 15 16 1718 19 Esc key Pressing this key cancels the operation the application program is executing F keys These F keys are assigned specific functions for each application Back space key Press the Back Space key to move the cursor to the left while deleting characters Insert key Press the Insert key to switch between character insert mode and overwrite mode Print Screen key Pressing this button copies the screenshot to the clipboard Home key Press the Home key to move the cursor all at once to the beginning of the current line or text Indicators The indictor lights when you press Num Lock Shift Caps Lock or Scroll Lock indicating that it is enabled When the key is pressed again the indicator turns off and the key function is disabled Caps Lock key Use the Caps Lock key to type alphabetical characters Press Shift Caps Lock to switch between uppercase and lowercase D5200_2 11 19 16 12 7 06 10 59 am E T o EE T 9 Ctrl key Use the Ctrl key in combination with another key Its function varies with each application 10 Windows key Press the Windows key to display the Start menu 11 Altkey Use t
29. other trademarks referenced are trademarks or registered trademarks of their respective owners whose protected rights are acknowledged Copyright Fujitsu PC Asia Pacific All rights including rights of translation reproduction by printing copying or similar methods in part or in whole are reserved Offenders will be liable for damages Allrights including rights created by patent grant or registration of a utility model or design are reserved Delivery subject to availability Right of technical modification reserved Fe DECLARATION OF CONFORMITY According to FCC Part15 Responsible Party Fujitsu Computer Systems Corporation Address 1250 East Arques Avenue Sunnyvale CA94085 Telephone Number 408 746 6000 Product Name Personal Computer Model Number FPC5D201DZ Conforms the following specifications FCC Part15 Subpart B Class B Digital Device This device complies with Part 15 of the FCC Rules Operation are subject to the following two conditions 1 This device must not be allowed to cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Website www pc ap fujitsu com o EE T i _ ae IMPORTANT SAFETY INSTRUCTIONS Read these instructions carefully Save these instructions for future reference Follow all warnings and instructions marked on the product Unplug this product from the wall outlet before cleaning Do no
30. owing cases e When the main unit of the personal computer is powered on e When the personal computer is in standby status power saving status e When the personal computer is resumed from standby status Power indicator Shows the status of the power to the main unit of the personal computer Lit in green when the computer is powered Lit in orange when the computer is in standby mode power saving status D5200_2 11 19 12 12 7 06 10 59 am E T I mo DESHE ON 4 Disc access indicator Lights up when data is being written to the hard disk or when data are read from the hard disk Optical drive or when an audio CD is played Some optical drives may light up when access is made to the a CD 5 USB ports Used to connect USB peripherals to your computer The ports are USB 2 0 compliant 6 Microphone jack S Connection jack for condenser microphone 7 Headphone jack Connection jack for headphone While a headphone is being connected sound does not come out from the line out jack of the main unit of the personal computer or internal speakers 8 CDeject button Press this button to eject the tray to insert a CD ROM or audio CDs or DVD Can be used when the main unit of the personal computer is powered on Do not press this button when access indicator lights up 9 Optical drive The optical drive allows users to play music CDs DVD Videos and CD ROMs Users can also write data on various DVD and CD rewritable
31. py protected it shall not be reproduced 2 When you reproduce the Software under the conditions in 1 above you may not modify delete or conceal the copyright statement on the Software 5 Transfer to a third party You may transfer the Software including all media and documentation accompanying your computer as well as its backup copy to a third party provided that you transfer the whole Software along with the computer on which the Software is installed You may not however transfer any media included with your computer separately from the computer D5200_0 INTRO 5 12 7 06 10 58 am E T 6 Modification and reverse engineering You may not modify the Software or reverse engineer the Software by decompiling or disassembling shall the third party or developer warrant the Software 7 High level of safety The Software is designed for general use i e for office use personal use and home use but not designed or manufactured for the use with a system that requires a high level of safety You may not use the Software with any system that requires a high level of safety without taking proper measures to secure safety for the system The term systems that require a high level of safety which include but not limited to the following refers to systems that require an extremely high level of safety and may directly affect human lives and bodies if safety is not secured Nuclear energy control systems flight co
32. r of the floppy disks Never clean the floppy disk drives with cleaning disks Any attempt would destroy the read write head in the disk drive within 20 seconds e 1 Insertion direction Label area Write protection switch for a 720 KB or a 1 44 MB floppy disk Identification of a 1 44 MB floppy disk or write protect switch on a 120 MB floppy disk Eject button for inserted floppy disks Disk is write protected N Oo oO FP WO ND Disk is not write protected To insert a floppy disk push it into the drive in the insertion direction until it engages The label should be facing upward 6 Toremove the floppy disk press the eject button 5 The write protect switch enables you to protect the data on the floppy disk from inadvertent overwriting or deletion 6 Toprotect the data on the floppy disk from being overwritten push the write protect switch to position 6 The hole is now visible Toremove write protection push the switch to position 7 The hole is now covered E Settings in BIOS Setup The BIOS Setup menu allows you to set your hardware configuration and system functions When the PC is delivered the default entries are valid You may customise these settings to your requirements in the BIOS Setup 18 D5200_2 11 19 18 12 7 06 10 59 am zz PS PH DIN E Anti theft Protection and Lead sealing There are three ways to protect your PC from theft With the Kensington Lock device 1 and with a Kensington Mic
33. r plugs out of grounded mains outlets Unplug all data communication cables from the utility sockets Disconnect all cables from the system unit and peripherals USB devices are hot pluggable This allows cables from USB devices to be connected and disconnected with the system switched on Additional information can be found in the documentation for the USB devices D5200_1 01 10 8 12 7 06 10 59 am or 00 N l l LI Connections on the system unit The ports for external devices are on the rear and on the front of the system unit The ports available on your PC depend on the configuration level you have selected The standard ports are marked with the symbols shown below or similar mannna Keyboard port purple PS 2 mouse port green AOON Serial interface 1 turquoise UJ Monitor port blue d Parallel interface Printer burgundy SN pe Microphone jack mono 1 pink Audio output Line out lime green SY Audio input Line in light blue kry USB Universal Serial Bus black LAN connector Some of the devices that you connect require special drivers see the operating system and device documentation D5200_1 01 10 9 12 7 06 10 59 am o E IT OQ Connecting external devices to the serial port External devices can be connected to the serial port e g a modem Connect the data cable to the external device 6 Connect the data cable to the serial port For an
34. roSaver With achain lead seal With a pad lock To prevent unauthorised persons from opening the casing the casing can be sealed To do this feed the sealing chain through the eye 2 and seal the chain with the lead seal You can also attach a padlock to the eye 2 to prevent unauthorised opening of the casing You can also use this eye to anchor the casing if necessary E How to Lock the Main Unit of the Personal Computer Rear Casing 1 Check that the upper cover has been firmly installed Agr t POINT The diameter of the hole for the security key installing fitting is 7 5 mm 2 Install a commercially available key to the security key installing fitting L 19 D5200_2 11 19 19 12 7 06 10 59 am KS Cf Chapter 3 Troubleshooting and Tips A CAUTION Take note of the safety notes and in the Preparing for use chapter when you connect or disconnect cables If a fault occurs try to correct it as described in the following sections in this chapter in the documentation of the connected devices in the help systems of the software used in the documentation of your operating system If you fail to correct the problem proceed as follows Switch the PC off Make a note of the steps and the circumstances that led to the fault Make anote of any error messages displayed 6 Contact your sales outlet or our customer service centre E Installing New Software When installin
35. roperly plugged into the PC and grounded mains outlet Switch on the monitor and the PC Monitor cable not connected Switch off the monitor and PC Check that the monitor cable is properly connected to the PC and monitor Switch onthe monitor and the PC 21 D5200 3 20 23 21 1217106 10 59 am E TT Wrong monitor has been set under Window XP Restart the PC Press F8 while the system is booting Either the Windows Advanced Start Options menu or the menu for selecting the operating system appears Ifthe menu for selecting the operating system appears press F8 Select Safe Mode or Safe Mode with Network Setthe correct values for the attached monitor as described in the operating manual of the monitor by selecting Start Settings Control Panel Display and then the Appearance Themes Settings tabs The wrong RAM modules have been inserted See the technical manual for the mainboard for information on which memory modules can be used E No Mouse Pointer Displayed on the Screen Shut down the operating system properly Switch the PC off Check that the mouse cable is properly connected to the system unit If you use an adapter or extension lead with the mouse cable check the connections Make sure that only one mouse is connected Switch the PC on The mouse controller must be enabled if you use a PS 2 mouse u 6 Check in the BIOS Setup that the mouse controller i
36. rsonal computer 1 Slide the lock buttons on the both sides of the main unit of the personal computer to the front ofit and remove the upper cover Slide the lock buttons to the main unit of the personal computer to the front side then raise the main unit to remove QO Expansion cards to be installed One PCI Express and one PCl standard expansion cards can be installed in this computer Up to 176 mm expansion cards half size can be installed 34 D5200_5 33 39 34 12 7 06 11 00 am zs Ps PH II QO Installing expansion cards 1 Unplug your computer 2 Remove power plugs LAN and modular cables from respective outlet 3 Remove the upper cover 4 Remove the installing fittings Raise the installing fitting upward When an expansion card has already been installed pull out the cable connected to the installed expansion card before removing 35 D5200_5 33 39 35 12 7 06 11 00 am e 00 PDK II POINT 6 Store the removed slot cover in a safe place When using an expansion card after removed install so that dust does not enter the internal personal computer 7 Insert the expansion card into the port Firmly insert the expansion card into the port and secure it by returning the lock raised in Step 4 8 Install the installing fitting Vertically install so that the tab is firmly positioned on the back side 9 Install the upper cover and connect LAN and modular cables 10 Inse
37. rt the power plug into a wall outlet and then turn on the computer The device driver and resource are automatically set so that the expansion card can be used POINT 6 Store the removed slot cover in a safe place After removing an expansion card reinstall the slot cover so that dust does not enter the internals of the computer 36 D5200_5 33 39 36 12 7 06 11 00 am Electrical Data o EE T ESPRIMO D5200 Rated voltage range selectable AC 100 120 V 200 240 V Frequency 50 Hz 60 Hz Max rated current Casing Max rating AC 100 V 120 V 7A AC 200 V 240 V 3 5A Dimensions Width depth height 89 W x 338 D x 332 H mm 179 W x 338 D x 344 H mm including footstand Weight with the basic configuration 7 7kg in basic configuration Environmental conditions Environment class 3K2 Environment class 2K2 DINIEC 721 part 3 3 DINIEC 721 part 3 2 Temperature e Operating 3K2 Transport 2K2 10 C 35 C 10 C 60 C Condensation in operating must be avoided Clearance required to ensure adequate ventilation e left front rear D5200_5 33 39 37 K min 200 mm min 200 mm min 200 mm 12 7 06 11 00 am 37 i _ ae T Some application may show the other name of this processor 2 The capacity of the disk provided in this manual is calculated by that 1 MB 1000 x 1000 bytes and 1 GB 1000
38. s Enabled Check that the mouse driver is properly installed and is present when the application programs is started Detailed information can be found in the user guide for the mouse and application programme The Floppy Disk Cannot be Read or Written Check that the write protection of the floppy disk drive is deactivated Check the entry for Diskette A in the Main menu of the BIOS Setup Check that the floppy disk drive controller is enabled Check that the cables of the floppy disk drive are properly connected 22 D5200_3 20 23 22 12 7 06 10 59 am zs Ps PH II E Time and or Date is not Correct You can set the time and date in the BIOS Setup or in the operating system Set the time and date If the time and date are repeatedly wrong when you switch on your PC the on board battery is flat CAUTION Do not touch the on board battery Risk of electric shock burn and fire Do not replace the on board battery Risk of explosion if battery is replaced by incorrect type Please contact Fujitsu or the store where you purchased this products E Error Messages on the Screen Error messages and their explanation are contained Inthe technical manual for the mainboard Inthe BIOS Setup manual Inthe documentation for the programmes used E Restoring the Hard Disk Contents Should you need to restore your hard disk the instructions are provided with the Recovery CD delivered with your system E Tips T
39. stalling memory n IMPORTANT 6 Hold the edge of the memory as shown in the following figure Be sure not to touch the areas pins with the indication of golden lines Do not touch these areas Memory When installing or removing memory take care so that the memory does not touch auxiliary fittings 1 Unplug your computer 2 Remove the power plug LAN and modular cables from respective outlets 3 Remove the upper cover 4 Remove the flat cable from the CD ROM drive 30 D5200_4 24 32 30 12 7 06 10 59 am Ps PH T 5 Open the hooks on the both sides of the slot outward 6 Insert the slot into the memory Align the notch of the memory to the notch of the slot and vertically insert the memory into the slot When the memory is correctly inserted the hooks on the both sides of the slot are raised Make sure that the hooks firmly hold the memory 31 D5200_4 24 32 31 12 7 06 10 59 am zs Ps PH II 7 Install the upper cover 8 Connect povver plugs LAN and modular cables POINT 6 When removing the memory refer to installing Steps Store the removed memory in a safe place Note that the hooks on the both sides of the slot should not be strongly forced opened Forced opening may cause the memory to jump resulting in failures 32 I D5200_4 24 32 32 12 7 06 10 59 am o EE T E Installing the Expansion
40. su grants you a license to use the software products Software installed on or included with your computer provided that you agree to all terms and conditions in Use of the Software below By using the Software you accept this License Agreement so read the terms and conditions in Use of the Software carefully before using the Software If separate license agreements or equivalent documents are included with some of the Software a higher priority will be given to them than to this License Agreement Use of the software 1 Use of and copyright on the Software You may use the Software solely on your computer You are granted a license to use the Software by purchasing the computer but the copyright on the Software remains the property of Fujitsu or its developer 2 Backup copy You may make one 1 copy of the Software solely for backup purposes 3 Incorporating the Software into other software If the Software is designed to be used as an add on to other software you may incorporate the whole or part of the Software into other software in accordance with the manual accompanying the Software 4 Reproduction 1 You may reproduce the Software solely for the purposes defined in Clauses 2 and 3 above Unless otherwise expressly stated in this user s guide or other documentation you may not reproduce the software into which the Software has been incorporated for any purposes other than backup purposes If the Software is co
41. switch the monitor on see the operating manual for the monitor Switch the PC on with the main power switch on the rear of the PC Press the ON OFF switch on the front of the PC The power on indicator lights green and the PC is started Switching Off the PC Shutdown the operating system properly For Windows select Shut Down from the Start menu Ifthe operating system does not automatically switch the PC off turn the PC to ready to operate when requested to do so by pressing the ON OFF switch If the PC is ready to operate the PC consumes very little power Switch off the PC at the power switch The PC no longer uses any power Q The main power switch and the power button do not disconnect the PC from the mains voltage To completely disconnect the mains voltage remove the power plug from the socket if necessary switch the monitor off see the operating manual for the monitor 11 D5200_2 11 19 11 12 7 06 10 59 am 12 Front Panels of the Main Unit of the Personal Computer Vent On the top of the computer there is an opening through which heatis forcibly discharged from the computer Note that the vent must not be blocked by objects When placed horizontally position the computer at a location where the vent is more than 20 cm away from the wall Power supply button Pressed in the foll
42. t use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Do not use this product near water Donotplace this product on an unstable cart stand or table The product may fall causing serious damage to the product Slots and openings in the cabinet and the back or bottom are provided for ventilation to ensure reliable operation of the product and to protect it from overheating these openings must not be blocked or covered The openings should never be blocked by placing the product on abed sofa rug or other similar surface This product should never be placed near or over a radiator or heat register or in a built in installation unless proper ventilation is provided This product should be operated from the type of power indicated on the marking label If you are not sure of the type of power available consult your dealer or local power company This product is equipped with a 3 wire grounding type plug a plug having a third grounding pin This will only plug into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the purpose of the grounding type plug Do not allow anything to rest on the power cord Do not place this product where the power cord can easily be stepped on If an extension cord is used with this product make sure that the total ampere rating of the equipment plugged
43. tarted the PC must not be switched off During installation the PC may only be rebooted when you are requested to do so Otherwise the installation will be not be performed correctly If a fault occurs during the installation the contents of the hard disk must be completely restored 0 Switching on monitor and PC Switch the monitor on Switch the PC on To do this follow the instructions below 1 Switch the PC on with the main power switch on the back panel Power button D5200_1 01 10 7 12 7 06 10 59 am I gj 06 ee To E Connecting External Devices Z CAUTION Do not connect or disconnect cables during a thunderstorm Always take hold of the actual plug Never unplug a cable by pulling the cable itself Connect and disconnect the cables in the order described below With the exception of USB devices always remove all power plugs before connecting external devices Read the documentation on the external device before connecting it Connecting cables Turn off all power and equipment switches Pull all power plugs out of grounded mains outlets Connect all cables at the system unit and peripherals You must observe the information provided in the chapter Important notes Plug all data communication cables into the utility sockets Plug all power cables into the grounded mains outlets Disconnecting cables Turn off all power and equipment switches Pull all powe
44. the LCD unit The fluorescent tubes in the LCD contain mercury Disposal of the LCD unit is controlled by the Waste Disposal and Public Cleaning Law To institutional and corporate customers LCD units must be disposed off as industrial waste Institutional and corporate customers are obliged to entrust an authorized industrial waste disposer To individual customers LCD units should be disposed off as general waste Individual customers are advised to follow the disposal rules and regulations set forth by the local municipality Disposal of batteries The wireless keyboard and mouse use dry batteries These batteries may explode when inflamed Disposal of the batteries is controlled by the Waste Disposal and Public Cleaning Law To institutional and corporate customers Dry batteries must be disposed off as industrial waste Institutional and corporate customers are advised to entrust an authorized industrial waste disposer To individual customers Dry batteries should be disposed off as general waste Individual customers are advised to follow the disposal rules and regulations set forth by the local municipality Q Reference to products In this manual the product names are referred to as follows This manual includes information on other operating systems o EE T Product name Description used in the manual Microsoft Windows XP Professional Edition Windows XP Professional Windows 7 Ti f Windo
45. the power unit The power unit is a box shaped device located at the rear of the internal main unit of the personal computer Precautions on handling internal cables or devices Do not scratch or machine internal cables or devices Taking precautions to static electricity The printed board and electronic devices in the internal peripheral devices are not protected by cases or other materials They may be damaged due to static electricity generated in your body Before handling them always touch an appropriate metal object to discharge static from your body Do not touch the printed board surface soldered areas or port areas Hold metal areas or the edges of the printed board Power to peripheral devices The power to peripheral devices is generally turned on before powering on the main unit of the personal computer however there are some peripheral devices that will be powered on after powering on the main unit of the personal computer Read the manual for peripheral devices Use ACPI support peripheral devices This personal computer supports ACPI one of the power control standards regarding energy saving If your computer uses the operating system that supports ACPI and when it uses peripheral devices inquire the manufactures of peripheral devices about whether these devices support ACPI The use of a peripheral device that does not support ACPI might cause malfunction of the personal computer and peripheral devices Preparing scre
46. their original packaging or in a packaging which protects them from knocks and jolts to the new site Do not unpack them until all transportation manoeuvres are completed Never drop the monitor Q Cleaning the PC A CAUTION Turn off all power and equipment switches and remove the power plug from the mains supply Do not clean any interior parts yourself leave this job to a service technician Do not use any cleaning agents that contain abrasives or may corrode plastic Ensure that no liquid enters the system Ensure that the ventilation areas of the system unit and the monitor are free Cleaning the system unit and the monitor Wipe the system unit and monitor casing with a dry cloth If particularly dirty use a cloth that has been moistened in mild domestic detergent and then carefully wrung out D5200_0 INTRO 10 12 7 06 10 58 am Q Disposal and recycling Disposal of the PC unit Disposal of the PC unit including accessories except the LCD unit is controlled by the Waste Disposal and Public Cleaning Law To institutional and corporate customers Personal computers must be disposed off as industrial waste Institutional and corporate customers are obliged to entrust an authorized industrial waste disposer To individual customers Personal computers should be disposed off as general waste Individual customers are advised to follow the disposal rules and regulations set forth by the local municipality Disposal of
47. wdrivers Phillips head screwdrivers may be required for installing or removing peripheral devices To avoid damage to the head of the screw use a screwdriver of an appropriate size D5200_4 24 32 26 12 7 06 10 59 am eo Lim TIT E Removing the Main Unit Cover VVhen connecting peripheral devices remove the upper cover so that the internal of the computer is exposed OU How to remove the main unit cover When the foot is installed remove the foot from the main unit of the personal computer to place the computer in the horizontal position before removing the upper cover 1 Slide the lock buttons on the both sides of the main unit of the personal computer to the front of it and remove the upper cover Slide the lock buttons to the main unit of the personal computer to the front side then raise the main unit to remove POINT When installing refer to removing steps 27 D5200_4 24 32 27 12 7 06 10 59 am E Installing Memory POINT 6 When installing memory after the purchase turn off your computer once after the setup of VVindovvs then install memory ZN WARNING ELECTRIC SHOCK A e Before installing or removing memory turn off the computer and connected devices and unplug the computer Othervvise you might get an electric shock HIGH TEMPERATURE Before installing or removing memory allow for sufficient time after turning off and unplugging the computer
48. ws Microsoft Windows XP Home Edition Windows XP XP Home Edition xi D5200_0 INTRO 11 12 7 06 10 58 am Si 1 Cs Ph l VVarning and Caution Labels Your PC bears the warning and caution labels as shown below The warning and caution labels must not be removed or damaged Top of the PC main unit warnine A Se Risk of EA t s AN n p Electric Shock To prevent electric shock tf always disconnect power gi source before removing exterior chassis to install change or remove external components ESPRIMO D5200 52 ei EH MODEL 22 5 FPC5D201DZ RATING E 100 1207200 240V 7 03 5A 50 60Hz Fe G m maaa Made in Singapore tutet under Quality Control of Fujitsu Limited Japan FUJITSU vin l sonson va AA RISK OF ELECTRIC SHOCK DISCONNECT POWER CORD AND ALL OTHER CABLES BEFORE REMOVING THE POWER SUPPLY REFER SERVCING TO QUALIFIED PERSONNEL ATTENTION RISQUE DE CHOC ELECTRIQUE DEBRANCHER LE CORDON SECTERUR ET TOUS LES AUTRES CABLES AVANT DE RETIRER LALIMENTETION LAMAINTENANCE DOIT ETRE ASSUREE PAR LE PERSONNEL QUALIFIE ee LE PETRAEA ERER ARR TEES A ACHTUNG GEF HRLICHE ELEKTRISCHE SPANNUNG NETZSTECKER STROMKABEL UND ALLE ANDERE STROMLEITUNGEN ZIEHEN BEVOR DAS NETZTEIL HERAUSGENOMMEN WIRD WARTUNG UND REPARATUR NUR DURCH ELEKTROFACHKRAFTE ATTENZIONE RISCHIO DI SCOSSA ELETTRICA SCOLLEGARE IL CAVO D ALIMENTAZIONE CORDOME E TUTTI GLI ALTR

MTD 45 Snow Blower User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents