Kenwood HM-437MP Stereo System User Manual
Contents
1. 7 COMPACT Hi Fi COMPONENT SYSTEM 6EN Q CD compartment O phones jack EQ X bass button To select the desired sound effect POP CLAS SIC ROCK JAZZ or FLAT to switch on off X BASS mode repeat button To repeat one track or all tracks for CD program button To program disc tracks for CD to program pre set radio stations for TUNER to set or reset clock for clock to set or reset timer for timer p call album buttons To select a preset radio stations for TUNER to select an album of MP3 Q b button To turn the system on or to standby mode standby indicator O rec button To record from TUNER or CD to a cassette tape to activate deactivate the demonstration in STANDBY or power on mode O timer on off button To switch the timer on off timer set button To view the clock or set the clock RDS display button To change the display for RDS to view the cur rent status of the system to change the time display for CD to change the information dis play for MP3 CD Remote sensor search gt 44 buttons To search forward backward to next previous track for CD to skip tracks for CD to search forward backward or to skip to the next previ ous album for MP3 to fast forward or rewind a tape to tune to higher lower radio frequency or search radio stations for TUNER to set the hour and minutes for clock to set timer func2. 875 MHz 108 MHz AM tuner section Tuning frequency range m 531 kHz 1 602 kHz CD player section PAS Che casei tees Semiconductor laser Over sampling 8 fs 352 8 kHz Laser wave length 760 800 nm Laser power class Class 1 IEC D A conversion 2 2 2 1 Bit Cassette deck section WACK qu 4 track 2 channel stereo General Power consumption 25W Dimensions W 145mm 5 11 16 H 210 mm 8 1 4 iiec E elec EE D 227 mm 8 15 16 Weight 2 8 kg 6 2 Ib Speakers Ericlos re ie Bass reflex type Speaker configuration Woofer 100 mm cone type 49 Maximum input 1 5W Dimensions W 130 mm 5 1 8 H 208 mm 8 3 16 D 161 mm 6 5 16 Weight net 1 2 kg 2 7 Ib 1 piece Notes e KENWOOD follows a policy of continuous advance ments in development For this reason specifica tions may be changed without notice e Sufficient performance may not be exhibited at tremely cold locations where water freezes KENWOOD 20 EN For your records Record the serial number found on the back of the unit in the spaces designated on the warranty card and in the space provided below Refer to the model and serial numbers whenever you call upon your dealer
3. TIMER OFF will start flashing Repeat the step and to set the time to stop the timer off time Press timer set button TIMER SET button on the remote control The icon TIMER will flash and the source display will appear Press program button PROGRAM button on the remote control El Press lt 4 or BPI button 44 or gt I SEARCH SKIP TUNING button on the remote control to select the desired source and press pro gram button PROGRAM button on the remote control to store the setting The source switches as follows CD TUNER TAPE RECTU recording tuner Press timer set button TIMER SET button on the remote control The icon TIMER will flash and the volume display will appear Press program button PROGRAM button on the remote control Press 4 or BPI button lt lt gt I SEARCH SKIP TUNING button on the remote control to set volume level and press program button PROGRAM button on the remote control to store the setting Press timer set button TIMER SET button on the remote control Press timer on off button TIMER ON OFF button on the remote control to activate timer mode The icon TIMER changes from flashing to steadily lit The timer is now set Switch the system to standby mode When reached the preset timer the selected source will play or switch to standby mode if the timer has been activated To activate deactivate the timer Press t
4. Wait until the moisture condensation at the lens has cleared Plug AC cord securely Radio reception Noise in radio Tune to a correct frequency Adjust the direction of the FM antenna AM antenna is built in rotate the sys tem to face a new direction Increase the distance between the sys tem TV or VCR Cassette deck operation Cannot record Replace the tape or cover tabs with adhesive tape Clean the head Use only NORMAL IEC tape Do not use a cassette with more than 90 minute recording time for the tape used in such a cassette is very thin and tends to cause problem such as en tanglement around the pinch roller or could be easily cut off Timer Clock The timer is not working Set the correct clock Press the TIMER ON OFF button to switch on the timer Switch the system to standby mode The timer clock is erased Power has been interrupted or power cord has been disconnected Set it again Remote control Does not function properly Replace the batteries Remove the obstacles Move closer to the system when us ing the remote control and make sure that you are pointing at unit s remote sensor 19 m z O I 2 T ENGLISH Specifications Main unit Amplifier section Rate output power Peer 5W 5W 1 kHz 10 T H D at 4 Q XSBASS ies cde neis 7 dB 60 Hz Tuner section FM tuner section Tuning frequency range
5. 10 seconds due to the large number of songs com piled into one disc e For MP3 CD on the display represents ALBUM e For MP3 CD the total album number on the display indicates the number of all the albums recorded in the MP3 CD Playing a normal disc Press IIl button Ii PLAY PAUSE button on the remote control to start playback The track number and elapsed playing time of the current track appear on the display To interrupt playback press button M PLAY PAUSE button on the remote control The playing time will start flashing To resume playback press I button gt 11 PLAY PAUSE button on the remote control again To stop playback press button Selecting a desired track passage To select a desired track Press 44 or BPI button 44 or gt gt SEARCH SKIP TUNING button on the remote control re peatedly until the desired track appears on the display f playback is stopped press I button I PLAY PAUSE button on the remote control to start playback The digit buttons 0 9 on the remote control can also be used to select a track Press the digit buttons as shown below To select track 2 2 and ENTER To select track 23 2 3 and ENTER To select track 120 MP3 CD only 1 2 and 0 To search for a particular passage during playback Press and hold 44 or gt gt button 9 4 or gt gt SEARCH SKIP TUNING button on the remote control and released it
6. El Program the desired sequence of CD tracks MP3 files See page 10 for programming procedure El Press rec button REC DEMO button on the remote control to set the unit into recording standby mode The icon REC appears on the display Press in button I1 PLAY PAUSE button on the remote control to begin recording Press button to end recording 15 m z 2 I ENGLISH Clock timer operation View clock The clock if it is set will be shown in standby mode To view the clock in any source mode CD TUNER or TAPE press timer set button TIMER SET button on the remote control The clock will be displayed If the clock has not been set 0 00 will start flash ing Clock setting Before carrying out the clock setting ensure that the system is in standby mode Press program button PROGRAM button on the remote control to enter the hour setting mode The hour indication will start flashing B Press I lt or gt gt button lt lt or gt gt SEARCH SKIP TUNING button on the remote control to set the hours El Press program button PROGRAM button on the remote control to enter the minute set ting mode The minute indication will start flashing El Press lt 4 or BPI button 144 9 or gt gt SEARCH SKIP TUNING button on the remote control to set the minutes El Press program button PROGRAM button on the remote control to store the setting The clock
7. TAPE Radio recording tip e To temporarily pause the recording press rec button REC DEMO button on the remote con rol Press It button gt 1m PLAY PAUSE but on on the remote control to resume record ing Recording from a CD MP3 CD nsert a blank cassette tape into the tape deck B Press CD button to CD nsert a CD MP3 CD and make sure that the unit is in stop mode Press lt 4 gt gt button 44 or gt gt SEARCH SKIP TUNING button on the remote control to select the first track you want to record El Press rec button REC DEMO button on the remote control to set the unit into recording standby mode The icon REC appears on the display Press button I1 PLAY PAUSE button on the remote control to begin recording Press rec button REC DEMO button on the remote control to interrupt recording Press button 7 PLAY PAUSE button on the remote control to resume recording Press button to end recording Notes e To ensure good system performance wait until the unit completely reads the disc before recording e During recording it is not possible to listen to an other source Program recording from a CD MP3 CD Desired CD tracks MP3 files can be programmed in the desired sequence and recorded onto a tape Insert a blank cassette tape into the tape deck Press CD button to CD El Insert a CD MP3 CD and make sure that the unit is in stop mode
8. copyright protection soci ety limited or the performing rights society lim ited In case of difficulty R Resetting the Microcomputer The microcomputer may malfunction unit can not be operated or shows an erroneous dis play if the power cord is unplugged while the power is ON or due to some other external factor If this happens execute the following procedure to reset the microcomputer and re turn the unit to its normal operating condition Plug in the AC power cord to the wall out let and within 5 seconds press and hold down the button and press CD button Please note that resetting the microcomputer will clear the contents of the memory and return the unit to the state it was in when it left the factory Check that following guide for problem resolution General No sound Plug in AC cord securely Set the VOLUME control to proper sound level Make sure the source is set to the source you wish to operate Pull out the headphones plug from the headphones jack The left and right sound outputs are reverse Check the speaker connections and location The system displays features automatically Switch off the demo operation CD player operation NO DISC is displayed Insert a disc correctly label side up Clean the disc Use a new or readable disc
9. for information or service on this product Model Serial Number
10. tion for timer button To start interrupt playback for CD To start playback for TAPE Q m button To stop playback for CD or TAPE To stop programming for CD Q Cassette tape compartment CD button To select CD input or turn the system on to CD input TUNER band button To select TUNER input or turn the system on to TUNER input When in TUNER input press the select the waveband FM or AM TAPE button To select TAPE input or turn the system on to TAPE input VOLUME buttons To increase or decrease the volume Standby mode While the standby indicator is lit a small amount of power is supplied to the system to back up the memory This is called standby mode Under the condition the system can be turned ON by the remote control unit JEN m z Q I T ENGLISH Basic function Demonstration mode The system is equipped with a demonstration function only display The demonstration consists of sequential change of display and indicators showing the operations but the audio itself does not change The demonstration function can be cancelled as follows To deactivate the demonstration Press and hold rec button REC DEMO button on the remote control for more than 0 8 seconds during demonstration To activate the demonstration After turning the power on press and hold rec button REC DEMO button on the remote con trol for more than 0 8 seconds Note Th
11. to program more than 60 files Press program button on the unit PROGRAM button on the remote control in stop mode to review the program sequence El Press gt I button gt m PLAY PAUSE button on the remote control to play the programmed files If you press repeat button on the unit REPEAT button on the remote control during pro grammed playback the current file or all pro grammed files will be played repeatedly The icon REPEAT or REPEAT ALL and the icon PROGRAM will appear on the display Press W button once to stop program playback or twice to clear the program The icon PROGRAM will disappear from the display Notes program is automatically cleared as soon as the CD door is opened e The function of program setting is disabling in PLAY PAUSE mode Random You can play all the tracks in random order During playing pause or stop mode press RANDOM button on the remote control to enable random play mode The icon RANDOM will appear on the dis play B To exit random mode press RANDOM button again The icon RANDOM will disappear from the display Note If the program function enabled and the repeat func tion is set on will disable the random play mode Repeat You can play the current track or the whole disc repeatedly To repeat all the tracks files Press repeat button on the unit REPEAT button on the remote control once in play or pause mode The ic
12. will start working To exit without storing the setting turn on the system Notes e The clock setting will be erased when the power cord is disconnected or a power failure occurred e The clock can be set in either 12 or 24 hour mode To change the mode When the system is in standby mode press TUNER band button while pressing PLAY PAUSE button 16 Timer setting The system can switch on to CD TUNER or TAPE mode automatically at a preset time serving as an alarm to wake you up The timer recording of radio programs onto a cas sette tape is also possible Important Before setting the timer ensure that the clock is set correctly When setting the timer playback or record ing for TUNER be sure to select the station you wish to tune in beforehand Turn the system on B Press timer set button TIMER SET button on the remote control twice to enter timer set ting mode The icon TIMER ON will start flashing on the display El Press program button PROGRAM button on the remote control The hour indication will start flashing El Set the time to start playback Press a lt or gt gt button lt lt or gt SEARCH SKIP TUNING button on the remote control to set timer start hours and press program button PROGRAM button on the remote con trol to store the setting Repeat the same procedure to set the minutes Press timer set button TIMER SET button on the remote control The icon
13. 50 cm Back panel 10 cm 4 EN CAUTION Place the unit where the AC power cord can be easily unplugged The power in this unit will not be completely cut off from the AC wall outlet when the power switch is turned OFF To cut off the power completely unplug the AC power cord from the AC wall outlet Names and functions of parts Remote control unit a POWER ALL RDS STEREO DISPLAY S EU INTRO RANDOM REPEAT TIMER SET CL 6 1 RE 1 2 3 DEF 4 GHI 5 JKL 6 MNO SLEEP C 7IPORS 8 TUV 9 WXYZ Loss 0 PROGRAM FILE SEARCH MUTE 525 25 MP D ED 11 o ec 4 1 9 TUNING AUNING e UP ERESI VOLUME DOWN S a a e TUNER mmm 9 E TAPE CD REC DEMO C JV 9 PLAY PAUSE Q mi Fi POALE 5 6 Q RDS DISPLAY button To change the display for RDS to view the cur rent status of the system to change the time display for CD to change the information dis play for MP3 CD PTY button To carry out PTY search the Europe only RANDOM button To carry out random playback for CD O INTRO button To play first several seconds for each track of CD REPEAT button To repeat one track or all tracks for CD digit 0 9 WXYZ buttons To se
14. A can only play the MP3 files in the first block e Supported VBR bit rate e Supported sampling frequencies for MP3 disc 32kHz 44 1kHz 48kHz e Supported bit rates of MP3 disc are 32 64 96 128 192 256 kbps Following formats can t be supported The files like AAC DLF M3U PLS Chinese name The non session closed discs The discs recorded under UDF format Contents Caution Read the pages marked A carefully to ensure safe operation A Before applying power 2 Safety precautions 2 Unpacking aci 3 Discs for playback 3 Preparing the remote control 4 COFIFIGClIORIS ren 4 Names and functions of parts 5 Remote control unit Main unit Basic function Demonstration mode Switching the system on Switching the system to standby mode 8 Volume control 2222 22 2 8 Sound control Headphones cec nte nodi Using the CD MP3 CD Loading a disc Playing a normal disc Selecting a desired track passage 9 Selecting a desired album file For MP3 CD 9 Programming tracks 10 Programming files For MP3 CD only 10 RAM
15. ANCE SERVICING INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE 1 THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER DEN Unpacking Unpack the unit carefully and make sure that all accessories are present Antenna terminal cover Screw for antenna terminal cover AM loop Remote control unit Batteries R6 AA f any accessories are missing or if the unit is damaged of falls to operate notify your dealer immediately If your unit was shipped to you di rectly notify your shipper immediately KENWOOD recommend that you retain the origi nal carton and packing materials in case you need o move or ship the unit in the future Keep this manual handy for future reference Discs for playback This system can playback all digital audio CD fi nalized digital audio CD Recordable CDR discs and finalized digital audio CD Rewritable CDRW discs This system can also playback CD DA for mat digital audio CD Support following MP3 CD formats ISO 9660 format Max 20 characters Max file number plus album is 896 Max nested directory is 8 levels The max ALB number is 256 including root ALB directory The max MP3 program file number is 60 This player can play mixed mode disc MP3 CDD
16. GOM 11 Repeat 5 en 12 Using the RDS DISPLAY button 12 Using the radio Sake 12 Tuning in radio stations 12 Storing preset eimi 12 Tuning to a preset radio station 13 Using RDS Radio Data System 13 Using the RDS DISPLAY button 13 Tuning by Program TYpe PTY search 19 Using the cassette 14 Playing a cassette tape 14 Recording on a cassette 14 Clock timer operation 16 View clock 16 Clock SEINO tette 16 16 To activate deactivate the timer 17 Sleep timer 17 General information 18 aintenanGe 18 Incase OT GITIGUILY 19 SPECIGI WONS 1 d teft heeded 20 z Q T ENGLISH Before applying power Preparing the remote control Insert batteries type R6 LR6 size into the remote control Operation When the standby indicator is lit the power turns ON when you press the POWER 5 button on the remote control When the power comes on press the button you want to ope
17. KENWOOD HM 437MP COMPACT Hi Fi COMPONENT SYSTEM m z 2 2 T SIVONVYS INSTRUCTION MANUAL m 9 gt 2 P COMPACT DIGITAL AUDIO KENWOOD CORPORATION B60 5521 08 00 C E 0404 ENGLISH Before applying power A Caution Read this page carefully to ensure safe operation Units are designed for operation as follows Europe ec te atten AC 230 V only The marking of products using lasers CLASS 1 LASER PRODUCT LASER KLASSE 1 APPAREIL A LASER DE CLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT The marking this product has been classified as Class 1 It means that there is no danger of hazardous radiation out side the product Location Bottom Safety precautions WARNING TO PREVENT FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SER RISK OF ELECTRIC SHOCK VICEABLE PARTS INSIDE REFER SERVICING TO QUALI BOINGTOREN FIED SERVICE PERSONNEL THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL WITHIN AN EQUILATERAL TRIANGLE IS TENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED DANGEROUS VOLTAGE WITH N THE PRODUCT S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTEN
18. ack the current track or all pro grammed tracks will be played repeatedly The icon REPEAT or REPEAT ALL and the icon PROGRAM will appear on the display Press button once to stop program playback or twice to clear the program The icon PROGRAM will disappear from the display Programming files For MP3 CD only Programming files of a disc is possible when play back is stopped Up to 60 files can be stored in the memory in any order In stop mode press program button on the unit PROGRAM button on the remote control to enter program setting The icon PROGRAM and P 01 will appear on the display indicates file number of the MP3 CD and 01 indicates program number Press p call album or button to select the desired album and press 44 or BPI button 44 or gt gt SEARCH SKIP TUNING button on the remote control to select the desired file The digit buttons 0 9 on the remote control can also be used to select files The icon PROGRAM and program number will start flashing El Press program button on the unit PROGRAM button on the remote control to store the se lected file The file number returns to and the next program number will appear on the display Repeat steps B to El to select and store other desired files in this way The icon PROGRAM will appear on the dis play and FULL will start flashing if you attempt
19. e demonstration operates automatically when a power failure has occurred or the plug of the power cable has been pulled out while the power was on Switching the system on Press b button on the unit or POWER button on the remote control or CD TUNER band TUNER BAND on the remote control or TAPE button The standby led will go out The system will switch to the last selected source or the selected source Switching the system to standby mode Press b button on the unit or POWER button on the remote control The clock will be displayed Volume control Press volume 4 button on the unit VOLUME UP button on the remote control to increase or press volume v button on the unit VOLUME DOWN button on the remote control to de crease the volume level Sen VOL XX will be displayed VOL XX denotes the volume level The volume can be adjusted in 32 steps from minimum to maximum To switch off the volume temporarily Press MUTE button on the remote control Playback will continue without sound only system speaker output and the icon MUTE appears on the display To restore the volume press MUTE button on the remote control again or adjust the volume Sound control EQ X BASS The sound control system feature enables you to enjoy special sound effects that have preset equal izer settings providing the best music reproduc tion Press EQ X BASS button To select the desired sound eff
20. ect POP CLAS SIC ROCK JAZZ or FLAT To switch the X BASS on off Press and hold the EQ X bass button on the unit EQ X BASS button on the remote control If X BASS is switched on BASS ON will appear then disappear on the display and the icon X BASS will appear on the display If X BASS is Switched off BASS OFF will appear then disap pear on the display and the icon X BASS will disappear Note X BASS functions are not applied to the record ing sound Headphones To listen to your stereo with headphones not in cluded use the 3 5 mm phones jack on the top of the unit Using the CD MP3 CD Loading a disc Press CD button to select CD MP3 mode E Press the area marked push open to open the CD door El Place a CD MP3 into the tray with the label facing up Close the CD door The total playtime and total number of tracks will appear in the display El Toremove the CD press the area marked push open grasp the CD by its edges and carefully pull it out For MP3 CD only Load a MP3 format music disc on the disc tray The total album number and total file number will appear on the display Notes e To ensure good system performance wait until the unit completely reads the disc before proceeding e f the CD compartment is not loaded with a CD MP3 CD or the CD MP3 CD is unreadable the mes sage NO PLAY will be blinking e For MP3 CD the disc reading time may exceed
21. en to Press TUNER band button TUNER BAND button on the remote control to TUNER mode Bl Press TUNER band button TUNER BAND button on the remote control to select FM Press PTY button on the remote control f the current station is with RDS the program type of the station is displayed continued to next page 13 m z 2 I 2 T ENGLISH Using the radio El Press PTY button on the remote control to select your desired program type Program type table Program Type Name Display News NEWS Current Affairs AFFAIRS Information INFO Sport SPORT Education EDUCATE Drama DRAMA Culture CULTURE Science SCIENCE Varied Speech VARIED Pop Music POPM Rock Music ROCK M Easy Music EASY Light Classical Music LIGHT M Serious Classical Music CLASSICS Other Music OTHER M Weather WEATHER Finance FINANCE Children s Program CHILDREN Social Affairs SOCIAL Religion RELIGION Phone In PHONE IN TRAVEL Leisure LEISURE Jazz Music JAZZ Country Music COUNTRY National Music NATION M Oldies Music OLDIES Folk Music FOLK M Documentary DOCUMENT El Press lt 4 or BPI button lt lt or gt I SEARCH SKIP TUNING button on the remote control to start searching Notes e Under certain receiving conditions it may take more than 1 minute to complete the search e If the desired pro
22. esigned for RDS reception can extract the information from the broadcast signal for use with various functions such as automatic display of the station name RDS functions PTY Program TYpe Identification Search Automatically tunes to a station that is currently broadcasting the specified program type genre PS Program Service Name Display Automatically displays the station name transmit ted by the RDS station Radio Text function Displays the radio text data transmitted by some RDS stations when you press RDS display but ton on the unit RDS DISPLAY button on the re mote control There is NO TEXT display if no text data is transmitted e The icon R D S appears on the display when an RDS broadcast signal is received Note Some functions and function names may differ certain countries and areas Using the RDS DISPLAY button While receiving a RDS station pressing RDS dis play button on the unit RDS DISPLAY button on the remote control changes the contents of the display Every time the button is pressed the display changes in a following order gt PS Program Service name display PTY Program TYpe display 1 RT Radio Text display Y Frequency display and preset number display Tuning by Program TYpe PTY search This function lets you set the tuner to automati cally search for stations which are currently broad casting the type of program genre you want to list
23. gram type cannot be found NO MATCH is displayed then after several seconds the display returns to the original display 145 Using the cassette Playing a cassette tape Press TAPE button to TAPE Bl Press the area marked push open to open the cassette compartment door El Insert cassette tape into the compartment with the open edge facing down Close the door securely El Press lt 4 or BPI button lt lt or gt I SEARCH SKIP TUNING button on the remote control to move tape to the desired starting point Press button I1 PLAY PAUSE button on the remote control to begin playing the tape Press volume buttons VOLUME UP or DOWN button on the remote control and press EQ X bass button EQ X BASS on the remote control to desired listening level Recording on a cassette tape You can record from the radio or the CD player For best recording use a normal bias tape Type 1 only Recording from the radio nsert a cassette tape into the tape compart ment and close door Press TUNER band button TUNER BAND button on the remote control to TUNER and select a radio station El Press rec button REC DEMO button on the remote control to set the unit into recording standby mode The icon REC appears on the display El Press n button It PLAY PAUSE button on the remote control to begin recording El Press button to end recording To turn off radio press TAPE button to
24. imer on off button TIMER ON OFF but ton on the remote control If activated the icon TIMER will appear on the display Notes The timer off will not be activated if the starting and stopping time are the same e If the selected source CD or RECTU is not available when preset timer is reached TUNER will be selected automatically e During timer setting if no button is press within 7 seconds the system will exit timer setting mode automatically Sleep timer setting If the sleep timer is activated the system will switch to standby mode after the selected time has expired Each press of the SLEEP button on the remote control decreases the timer period by 10 minutes The sleep timer can be set up to 90 minutes The display will change to sleep time display and change as follows 90 min 80 min 70 min 60 min 50 min 40 min 30 min 20 min 10 min OFF 90 min 80 min The icon SLEEP will appear on the display While sleep mode is in active To deactivate the sleep timer Press SLEEP button on the remote control or press the button to turn the power off Note If timer off and the sleep off are all activated the sys tem will switch to standby mode by the earlier timer set 17 m z 2 I 2 T ENGLISH General information Maintenance Cleaning the cabinet e Use a soft cloth slightly moistened with a mild detergent solution Do not use a solution c
25. lect a track number for CD to select a preset radio station for TUNER to enter file names in file search mode for MP3 CD PROGRAM button To program disc tracks for CD to program pre set radio stations for TUNER to set or reset clock for clock to set or reset timer for timer ENTER button To confirm the selection in file search mode for MP3 CD SEARCH SKIP TUNING buttons To search forward backward to next previous track for CD to skip tracks for CD to search forward backward or to skip to the next previ ous album for MP3 to fast forward or rewind a tape to tune to higher lower radio frequency or search radio stations for TUNER to set the hour and minutes for clock to set timer func tion for timer TAPE button To select TAPE input or turn the system on to TAPE input TUNER BAND button To select TUNER input or turn the system on to TUNER input When in TUNER input press the select the waveband FM or AM PLAY PAUSE Il button To start or interrupt playback for CD To start playback for TAPE STEREO MONO button To switch between stereo mode and mono mode on FM band only for TUNER POWER b button To switch the system on or to standby mode Q Clock and timer related buttons TIMER SET button to view the clock or set the clock TIMER ON OFF button to switch the timer on off SLEEP button to select the sleep time EQ X BASS button To select the desired sound effec
26. on taining alcohol spirits ammonia or abrasive Cleaning discs When a disc becomes dirty clean it with a cleaning cloth wipe the disc from the center out Do not wipe in circular motion Do not use solvents such as benzene thinner commercially available cleaners or antistatic spray intended for analogue records Cleaning the heads and tape path To ensure good recording and playback qual ity clean the heads the capstans and pres sure rollers after every 50 hours of tape opera tion e Useacotton swab slight moistened with clean ing fluid e You also can clean the heads by playing a clean ing tape once 185 Caution on condensation Condensation of dew may occur inside the unit when there is a great difference in temperature between this unit and the outside This unit may not function properly if condensation occurs In this case leave the unit for a few hours and re start the operation after the condensation has dried up Be specially cautious against condensation in the following circumstances When this unit is carried from one place to an other across a large difference in temperature when the humidity in the room where this unit is installed increases etc Warning notice In most cases it is an infringement of copyright to make copies of tapes or discs without the per mission of the copyright owners Anyone wishing to copy commercially available tapes or disc should contact the mechanical
27. on REPEAT will appear on the dis play All tracks files will be repeated continuously To cancel repeat play repress repeat button on the unit REPEAT button on the remote con trol twice for a normal CD and 3 times for a MP3 CD To repeat a single track file Press repeat button on the unit REPEAT button on the remote control twice for a normal CD and 3 times for a MP3 CD in play or pause mode The icon REPEAT will appear on the display To cancel repeat play repress repeat button on the unit REPEAT button on the remote con trol once continued to next page 11 z 2 I 2 T ENGLISH Using the CD MP3 CD To repeat one album For MP3 CD only Press repeat button REPEAT button on the re mote control twice in play or pause mode The icon REPEAT ALB will appear on the dis play To cancel repeat play repress repeat button on the unit REPEAT button on the remote con trol twice Note In program mode you can only select repeat one or repeat all function Intro scan This function let you listen to the first 10 seconds of each track throughout the disc Press INTRO button on the remote control to start scanning and the icon INTRO will appear on the display To stop the intro scan Press INTRO button on the remote control again The unit enters normal play mode and starts play ing from where you stop the scanning Using the RDS DISPLAY button Pres
28. ontrol to start playback Programming tracks Programming tracks of a disc is possible when playback is stopped Up to 60 tracks can be stored in the memory in any order In stop mode press program button on the unit PROGRAM button on the remote control to enter program setting The icon PROGRAM and P 01 will appear on the display indicates track number of the CD and P 01 indicates pro gram number Press lt 4 or BPI button lt lt or gt I SEARCH SKIP TUNING button on the remote control to select the desired track The digit buttons 0 9 on the remote control can also be used to select tracks The icon PROGRAM and program number will start flashing 10 El Press program button on the unit PROGRAM button on the remote control to store the se lected track The track number returns to and the next program number will appear on the display El Repeat steps to to select and store other desired tracks in this way The icon PROGRAM will appear on the dis play and FULL will start flashing if you attempt to program more than 60 tracks Press program button on the unit PROGRAM button on the remote control in stop mode to review the program sequence El Press button 7 PLAY PAUSE button on the remote control to play the programmed tracks If you press repeat button on the unit REPEAT button on the remote control during pro grammed playb
29. rate Notes The supplied batteries may have shorter lives than ordinary batteries due to use during operation checks e When the remote controllable distance gets shorter than before replace both batteries with new ones e Placing the remote sensor in direct sunlight or in direct light from a high frequency fluorescent lamp may cause a malfunction In such a case change the location of the system installation to prevent malfunction Connections Connecting the AM antenna Set up the AM loop antenna and then connect it Speakers connection Connect the right speaker to terminal marked R with the red wire to and the black wire tos Connect the left speaker to terminal marked L with the red wire to and the black wire to Clip the stripped portion of the speaker wire as shown A CA CA t Notes For the FM antenna Adjust the position of the FM antenna for the best reception For optimal sound performance it is recommended to use the supplied speakers Do not connect more than one speaker to any one pair of speaker terminal CAUTION Be sure to adhere to the following or proper ventilation will be blocked causing damage or fire hazard Do not place any objects impairing heat radiation onto the top of the unit Leave some space around the unit from the largest outside dimension including projection equal to or greater than shown below Top panel
30. sing RDS display button on the unit RDS DISPLAY on the remote control shows various display information of the disc such as time infor mation of the current track or a whole disc pro gram number during program play file and artist name during mode and etc 12 Using the radio Tuning in radio stations Press TUNER band button TUNER BAND button on the remote control to select TUNER mode The current radio frequency will be displayed Press TUNER band button TUNER BAND button on the remote control to select the desired waveband FM or AM El Press and hold 44 or BI button 44 or gt gt SEARCH SKIP TUNING button on the remote control Repeat this procedure until the desired station is reached To tune to a weak station briefly press I t or P button 44 or gt gt SEARCH SKIP TUN ING button on the remote control repeatedly until the display shows the desired frequency or when the best reception has been obtained Storing preset You can store up to 20 for FM and 20 for AM radio stations in the memory When a preset radio sta tions selected The preset number appears on the display Press TUNER band button TUNER BAND button on the remote control to select TUNER mode Bl Press TUNER band button TUNER BAND button on the remote control to select the desired waveband FM or AM El Press lt 4 or BPI button lt lt or gt I SEARCH SKIP TUNING button on the remote control to
31. t CLAS SIC ROCK JAZZ or FLAT to switch on off X BASS mode MUTE button To interrupt and resume sound reproduction FILE SEARCH button To select a desired file in an MP3 disc VOLUME UP DOWN A Y buttons To increase or decrease the volume CD button To select CD input or turn the system on to CD in put G REC DEMO button To record from TUNER or CD to a cassette tape To activate deactivate the demonstration in STANDBY or power on mode m button To stop playback for CD or TAPE to stop pro gramming for CD PCALL A Y buttons To select a preset radio stations for TUNER HEN m z 2 2 T Names and functions of parts Main unit ENGLISH r ALB icon r INTRO icon SYNC icon SLEEP icon RDS icon ALL icon MP3 icon CD R RW Playback J TOTAL icon m G REC icon TIMER icons REMAIN icon FILE SEARCH icon o INTRO f FILE SEARCH D s KENWOOD STEREO Sound effect X BASS icon icons icon L Frequency display Preset channel display Playback time display etc Play mode icons 22 9 9 lt
32. tune to the desired frequency El Press program button PROGRAM button the remote control so that will start flash ng El f you wish to store the radio station to another preset number p call album button P CALL button on the remote control or p call al bum button P CALL button on the remote control to select the desired preset number Press program button PROGRAM button on the remote control again to store the radio station Repeat steps to to store other preset ra dio stations Note During program if no button is press within 20 sec onds the system will exit program mode automatically Tuning to a preset radio station Press p call album button P CALL button on the remote control or p call album button P CALL button on the remote control or digit but tons 0 9 on the remote control to select the desired preset number The preset number and radio frequency will appear on the display STEREO MONO Press the STEREO MONO button on the remote control to select mono or stereo mode When stereo mode is selected the icon STE REO will appear on the display if current sta tion is FM stereo Note You are able to select stereo or mono mode in FM band only Using RDS Badio Data System RDS is a system that transmits useful informa tion in the form of digital data for FM broadcasts along with the broadcast signal Tuners and receiv ers d
33. when the desired passage is located for CD Selecting a desired album file For MP3 CD only To select a desired album Press p call album or button on the unit until the desired album number appears on the display e xxx will appear on the display indicates album number and indicates the file number To select a desired file Press 44 or gt gt button I lt gt gt SEARCH SKIP TUNING button on the remote control re peatedly until the desired file from the current al bum appears on the display e xxx will appear on the display indicates album number and xxx indicates the file number The digit buttons 0 9 on the remote control can also be used to select a file continued to next page Q EN m z 2 2 T ENGLISH Using the CD MP3 CD To search a desired file by file name Press FILE SEARCH button on the remote control B Press the digit buttons to enter the first char acter of the file name you wish to search and press ENTER button Repeat this procedure to enter the rest of the file name Press FILE SEARCH button on the remote control The icon FILE SEARCH will appear on the display If the unit finds an appropriate file the file name will be scrolled on the display If there is no appropriate file NO FILE will be appeared Press gt I button gt 1 PLAY PAUSE button on the remote c
Download Pdf Manuals
Related Search