Kelvinator KL72TT Washer/Dryer User Manual
Contents
1. Do not use water hotter than 50 C Do not put the machine at damp place like the bathroom Never wash it with water Do not place wet laundries on the control panel Do not wash water proof laundries such as the raincoat bicycle shelter etc To avoid abnormal vibration during spinning Do not share one receptacle with other electric appliances Do not use it in case that the power plug is damaged or the inserting into the receptacle is loose Safety precautions Before Using Do not stretch hands into the working machine It is dangerous even if the rotation is slow Take special care of the children Do not decompose repair or alter the machine by yourself Do not put any hot or heavy items such as the kettle with hot water on the washing machine Do not wash laundries with volatile materials such as thinner petrol etc Handicapped or children without care shall not use the machine Keep the machine away from direct sunlight and heat source like the heater _ Toprotect your laundries and washing machine please take out all of the coirs buttons sand hairpin and other foreign materials before washing Sy o _ Please check if the water faucet is open and if the connection of the water inlet pipe is proper itis suggested to use foamless washing powder Installation and a2. Take off the drain hose uei Take off the drain hose from the hanging l hole of the cabinet Pull the drain hose T nee fixing hook outwards gently to take out the drain hose from the two fixing hooks As per Figure 2 Rotate the drain hose fixing hook for 90 to take it out from the installation hole ee As per Figure 3 Rotate the fixing m hook for 90 a z Install the two drain hose H oF SZ fixing hooks taken out into Take off the fixing the installation hole at the pokso E Cyistalatonfte toners other side of the base frame Figure 3 Figure 4 to aim at the installation hole accurately you can lean the washing machine forward slightly Then rotate for 90 As per Figure 4 Pull the fixing hook outwards slightly i Inlay the drain hose into the fixing hooks a S reliably along the groove at spin tub side and make it extend towards spin tub side agurea Figure 6 Then hang the drain hose into the hanging hole atthe spin tub side As per Figure Extend the drain hose from the rear side Take out the drain hose from the fixing hook Extend it from the rear side When t
3. about46L About 38g About 46g Below2 5kg Minimum about36L About 30g About 36g Selection of the current water level and washing time list 2 Laundries Water level Washing time Current quantity Water quantity ahehe minutes Knitwear About3 6 a Cotton blending linen About8 10 Maximum about55L Very dirty and thick About10 13 Bed sheet About7 13 Medium about46L 3 2kg 7 2kg Strong Minimum about36L Silk thin laundries About2 4 F Chemical fiber About3 6 Cotton blending linen About8 10 Below3 2kg Standard Medium about46L Using process Water filling selector handle Washing sequence Overfilling sig Spin timer fto set to below 1 minute irst set to 2 minute then Wash selector Water filling entrance Buzzer Strong current The buzzer will ring when standard current the washing finishes turn it back it can increase the service life of the timer Wash timer To set to below 2 minute irst set to 5 minute then turn it back it can increase the service life of the timer BUZZER WASH SELECTOR Wash 1 Water filling selector 1 Set the water filling selector at the WASH side Figure 1 2 Set the water level adjusting lever to needed line 2 Fill the water and add the dissolved washing powder to make the water level reach the preset position Figure 2 Run washing program for some time to stir a
4. Kelvinator XR KL72TT Twin tub Washing Machine with Pump Contents Before using Names of the parts the 2na cover Safely precautions m 1 Installation and adjustment 3 Introduction of the major functions 5 Using process Preparation before washing 6 The musts IN WASHING m es 7 Usage of the detergent 0 00 8 Washing SeQuenCe c5 access 9 Disposal after washing 0 0 13 Please read this manual carefully before using Trouble shooting e Retain it for future reference Answers to question 15 Please check if the power receptacle has good earthing Packing li 17 condition before using to guarantee your safety acK ng S a S The manufacturer will not bear the responsibility for Specification the back cover those risks occurred from not obeying this manual Names of the parts Before Using Buzzer Water filling entrance Outer cover of the spin tub Water inlet selector handle Inner cover of the spin tub Wash selector Wash timer Spin timer Control panel Spin tub frame Overflow filter r Spin tub Quick water filling entrance p gt l Drain hose surpport i I Cabinet Water level adjusting lever yi Power cord Lint filter installed by user fi Pulsato N Wash tub Drain hose gt Wash tub cover Base frame Accessories Meaning and description of the symbols Content
5. before sending it to repair If there are real breakdowns please come to the special maintenance department or after sale service department of our company Do not repair it by yourself Phenomena The machine does not act The reason Is there power failure Is the power plug loose Is the pulsator twisted by foreign materials The draining does not work Is the drain hose frozen Is the drain hose blocked by foreign material Are there laundries falling to the outer side of the spin tub There s abnormal sound during washing Are there hair pin coins or metal items brought inside the tub There s abnormal sound and violent vibration during spinning Is the machine slanting Is the gland pressed evenly Are there laundries falling to the outer side of the spin tub Are the laundries in spin tub too much There may be some water flowing out of the drain hose in the first use of the machine It is the water remained in the factory inspection of performance Packing list User s manual Water inlet hose Water filling jointer Gland Lint filter Twin tub washing machine 17 Specification Type Twin tub washing machine with pump Model KL72TT Power source Rated voltage 220V Rated frequency 50Hz Water level Water quantity about Maximum 55L_ Medium 46L Minimum 36L Rated washing capacity kg 7 2 Rated spinnin
6. djustment Before Using Please install and adjust the machine according to the requirement of the manual It is very important to your security and correct operating the machine The drainage shall be smooth with the drain hose 1 The height of the drain hose shallbe less than 1 2m or the drainage will not be smooth enough and cause incomplete drainage 2 Do not step on or press the drain hose Install the lint filter After opening the package please take out the lint filter from the doqiment bag install it to the overflow filter of the cabinet See to the figure Overflow filter S d Lint filter Install the water inlet hose Select the water level Insert the water inlet hose into the water filling Vater inlet hose entrance on the control pane directly pull it out to dismantle it The appliance is to be connected Water inlet to the water mains using new hose sets and that old hose sets should not be reused eee Select water level according to the quantity of the laundries Maximum _ Max Set the water level adjusting lever o to needed line Neen Minimum gt Pages about 36L Me Medium gt Min Before Using How to change the direction of the drain hoses e Figure 1 indicates the ex factory n ey l installation position of the drain Figure 1 fixing hook installation hole hose Pull outwards Drain hose slightly Extend the drain hose from the side of spin tub y
7. g capacity kg 6 0 Rated input power W Wash 320 Spin210 Dimensions mm L810 W460 H926 Wash pattern New current Weight kg 27 Injection pressure 0 02MPa 0 2MPa
8. he drain hose is extended from the rear side it can be hung on the point for drain hose at the two sides of the cabinet See to Figure 6 Introduction of the major function Using process The machine has good comprehensive performance and nice appearance It adopts streamline appearance and full plastic shell which will never get rust For the design on safety and reliability it adopts the wash shelf spin shelf and water reception groove design and reduces the unfavorable influence on the electrical component by the vapor Therefore it guarantees more safe and reliable washing By the technology of comprehensive energy saving the machine can work under wide range of voltage regardless of the voltage fluctuation It adopts complete enclosed base frame and low noise motor and thus reduces the working noise significantly We can guarantee that the purchase of this machine will bring you a Clean world without disturbing your quiet life Foam removing spinning during high efficiency rinsing Foam removing Use the foam removing spinning to ae 25 spinning pin remove the extra detergent liquid It can both shorten the washing time and save the water consumption Fill water for Spin for about about 1 minutes 1 2 minutes Remove most of the foam extra Remove the detergent detergent liquid liquid remained The effect is best when the laundries quantity is below 80 of the rated value Quick water filli
9. l usage of the machine Please clean it every two months 1 Take off the overflow filter As indicated in the figure nip the elastic fixing claw and pull it to the direction of the arrow to take it off Elastic fixin claw 13 14 Cleaning the overflow filter 2 Take off the corrugation pipe Dismantle the upper part of the corrugation pipe inside the overflow filter as indicated in Figure 1 Cleaning the overflow filter Clean the lint around the filter and flush with tap water Install the overflow filter 1 Install the corrugation pipe 2 Insert the mounting plate at the bottom of the filter into original position 3 Hang up the hook at the left upper side 4 Push the upper part in as indicated in Figure 2 Using process Water level adjusting lever Corrugation Pipe Figure 1 Figure 2 Disposal of the complete unit Wipe the complete unit with soft cloth twisted dry Wipe with neutral detergent if too dirty Do not wash it directly by water After washing dismount the water inlet hose Do not store water in the tub for long period Discharge the water immediately after each using Pull off the power plug and hang up the power cord Hang up the drain hose Wipe off the water drops on the surface and inside the tub with clean soft cloth Open the cover of the wash tub and the inner outer cover of the spin tub for some time about one hour then close
10. nd dissolve the powder completely WASH _SPIN_ gt INLET SELECTOR Figure 1 WASH SELECTOR STRONG E Page 8 3 Put in the laundries If the water quantity is insufficient please add water Figure 3 Page8 4 Select the current Select the strength of the current according to WASH TIMER ore the laundries Figure 3 Page 8 Ca YNZ Figure 4 5 Select the washing time Select the washing time according to the laundries WASH SELECTOR STRONG Page 8 i STANDARD 6 After washing the buzzer will ring Set the WASH i Figure 5 SELECTOR at DRAIN Figure 5 Using process Midway spinning 1 Put the laundries into the spin tub evenly and smoothly 2 Spin 1 Put the gland in properly e Please put in the gland properly even if the laundries quantity is small Push Gland Proper The laundries are slanting Proper No gland 2 Close the inner and outer cover of the spin tub Outer cover of The spin tub Inner cover of 3 Spin for 1 2 minutes The spin tub 3 Run the foam removing spinning 1 Open the outer cover of the spin tub 2 Set the water filling selector control rod at the SPIN side Fill water for WASHI SPIN about 1 minute e f the water quantity filled is too large the water may flow out from the wash tub side Please twist the water tap to limit the water filling 3 Close the outer cover of the spin tub S
11. ndries Putthose laundries difficult to absorb water into water with hand For those laundries with heavy soil please first remove the dirt like mud or dust For the parts with heavy soil please apply detergent on them in advance which can makeit easierto remove the soil For those laundries that may get lint ball and those with long fur turn it over before putting in Do not put those laundries polluted by chemicals into the washing machine directly The musts in washing Using process The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time Laundries quantity in one washing cycle shall be lower than the rated capacity The largest wash capacity of this mach ine is 7 2kg The largest spin capacity of this machine is 6 0 kg The thickness size type of the cloth will influence the actual washing capacity It is suitable to put in reasonable amount of laundries and the laundries can be turned round in washing for one time washing Do not select Maximum water level for laundries less than 3 2kg so as to avoid splashing of water Working suit up down cotton about 1120g Jeans about 800g Blanket cotton about 900g C2 Up Blending coat about Le Jacket Shirt F Eo about onon abot S SS Single bed sheet gA j cotton about 600g cotton about 180g Underpa
12. ng entrance If you do not need spraying spin you can fill water into the wash tub directly through this entrance It can reduce the humidity inside the control panel significantly and prolong the operating life of the components Quick water filling entrance Preparation before washing Check if the laundries has special requirement on washing Clear pocket out the the Take coins sand hairpins etc Fi D AO Preparation before washing 1 Connect the water inlet hose 2 Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle Do not connect the earth terminal to the gas pipe and tap water pipe 3 Put the drain hose up to suitable Using process position A 4 Slanting or uneven ground may result in unstable working or abnormal noise Please make the machine stand horizontally Pay attention to followings before washing the laundries Tie the long strips fasten the buttons close zippers The quantity of the laundries shall not be too large Stretch and loosen the laundries before putting them in the tub lt 2 When the pulsator is running the buttons of the laundries may cause noise For the sake of discretion please put the laundries with buttons into other laundries Check if the laundries are applicable for washing with machine Divide the laundries that are not colorfast from other lau
13. nts Socking g cotton about 70g blending about 50g Undershirt Usage of the detergent Using process How to use the whitener Fill water to decided level Dilute the whitener with container Pour it slowly into the washing tub Avoid using whitener on laundries with color or pattern as they are prone to lose color The whitener shall not touch the laundries directly Refer to the user s manual for the usage and quantity of the whitener For powder whitener please dissolve it before using How to use the washing powder Direct dissolved in the machine The powder is more prone to pollute the 1 Fill small quantity of water laundries than the detergent Therefore 2 Add the powder Run for 30 seconds to please use it with proper quantity dissolve it completely 3 Put it in the laundries Select suitable i s o ine not to use high sudsing water level etergent The instant dissolving of the washing powder Dosage of different washing powder is 1 Prepare warm water of 30 C and a container different Please refer to the instruction 2 Add the powder while stirring to fully of the washing powder for the detail dissolve it dosage Selection of the quantity of the washing powder list 1 Standard dosage Laundries Water level quantity Water quantity Concentrated washing Common washing powder powder 4 5kg 7 2kg Maximum about55L About 46g About 55g 2 5kg 4 5kg Medium
14. ormal sound it is generally owing to slanting placement of the laundries Please stop the machine and re order the laundries In spinning it will pause the work if you open the outer cover of the spin tub Close it to resume the spinning d To do spinning and draining or rinsing oo with water filling together please first do spinning for around 1 minute then do draining or rinsing with water filling Otherwise the spinning will stop owing to too much water stored in the spin tub eC Disposal after washing Using process After using please clean the lint and foreign materials of the lint filter and overflow filter in time Otherwise it may influence your using the machine Please first pull off the power plug from the receptacle before cleaning Cleaning the lint filter The lint filter must be used during washing it must be cleaned in time after each using Take off the lint filter Put hand at the indicated position Push down to take it off See to Figure 1 Figure 1 Clean the lint Put it in water and clean while it is still wet See to Figure 2 Figure 2 Install the lint filter After cleaning insert the bottom of the lint filter marked with DOWN SIDE into the overflow filter then push the upper part of the filter in marked with UP SIDE Figure 3 See to Figure 3 Cleaning the overflow filter Too much lint on the overflow filter will influence the norma
15. pin for 1 2 minutes WATER INLET SELE 10 Rinsing Rinse with water filing 1 Put the laundries into the wash tub Select suitable current according to the laundries Page J gt 2 Adjust the water level Set the water level with water level adjusting lever according to the laundries quantity Then fill suitable water continuously 3 Rinse Adjust the wash timer to 5 7 minutes to do rinsing Rinse with stored water Using process If you find water flo wing out here please twist the water tap to limit the water filling Vv Repeat the midway spinning and rinsing with stored water for 2 3 times Put the laundries into the wash tub Select suitable current according to the laundries Page J gt Fill water to preset water level Rinse Adjust the wash timer to 2 3 minutes to do rinsing When the laundries quantity is below 3 2kg please use STANDARD current If you use STRONG current it may splash 11 12 Using process Spinning 1 Put the laundries into the spin tub Selection of the spin time list 3 evenly and smoothly inti Sas Press the gland in the tub properly oe eet or About 4 5 Close the inner and outer cover of the spin tub Underwear E knitwear About 2 4 Swear Spin chemical fiber About 1 2 Select suitable spin time according to the laundries and do spinning ndina hin Within 1 minute During spinning if there s abn
16. s marked with that symbol Warning sign 3 related to the safety of the product and the personal safety of the users Please operate in Water inlet hose strict conformity to the contents one piece otherwise it may cause damage of the machine or injure the personal safety of the user Water filling jointer one piece Lint filter Forbidding sign Contents marked with that symbol one piece are actions forbidden to perform Performing of those actions may Gland result in damage of the machine one piece or injure the personal safety of the user Safety precaution Please insert the power cord into special receptacle with rated voltage Be sure to use single phase three pins receptacle The earthing terminal of the receptacle must be earthed reliably If possible please adopt electric leakage protector sS Before Using The washing machine should be position ed sothat the plug is accessible Be sure to pullthe plug off when there spower fai lure orthe machine is being moved cle aned or when itis idle If the supply cordis damaged it must be replaced by the manufacturer it s service agent or similarly qualified persons in order to avoid a hazard Keep the pin ofthe Power plug clean The carpet must not obstruct the ven tilation openings in the base of the wa shing machine Ventilation hole at the bottom of the i washing machine
17. them Trouble shooting Answer to question If the laundries fall to the outer side of the spin tub If the laundries fall to the outer side of the spin tub please take them out immediately 1 Dismantle As indicated in the figure push the point marked with X to pull the spin tub frame to oblique upwards to dismantle it 2 Install After install the back edge of the spin tub frame to proper position push the four points marked with X by force to reset it Please check carefully The laundries may fall to the lower part of the outer side of the spin tub as indicated in the figure if the laundries fall to the outer side of the spin tub during spinning the draining will get blocked and the rotation speed of the spin tub is reduced iad j Laundries When the remained water is frozen Prevent the freezing be sure to discharge the water completely after using After complete draining set the WASH SELECTOR at STRONG or STANDARD If itis set at DRAIN it will be rather difficult for the frozen water to melt When the water is frozen Pour hot water below 50 C into the wash tub to soak it completely Then turn the pulsator with hands gently Please confirm the drainage can work normally before next using 15 16 Trouble shooting Answer to question If there s breakdown please pull off the power plug before checking The following phenomena are not breakdowns sometimes Please confirm again
Download Pdf Manuals
Related Search