Husqvarna 500HD 56EL Trimmer User Manual
Contents
1. H Husqvarna 900HD 56EL 600HD 60EL GB 1 2 Operating switches two hand operation Hand guard Mains flex with plug Blade safety rail Impact protector Locking of the turning handle Illustration and Explanation of Pictograms AQ Wear eye and ear protection Warning Read the instruction manual Do not use the tool under wet weather conditions Unplug immediately if the power cord or plug becomes damage ah ON Hedge Trimmer 1 Introducing the hedgetrimmer ENGLISH Technical data 500HD 56EL 600HD 60EL Operating Voltage V 230 230 Nominal Frequency Hz 50 50 Nominal Consumption W 500 500 Mains Safety Fuse A 16 16 Cutting movements min 3600 2400 Shear length mm 560 600 Cutting Thickness mm 22 21 Weight without flex kg 3 6 3 7 Noise Pressure Level LpA according to EN 50144 88 dB A 89 dB A Vibration according to EN 50144 lt 4 7 m s2 lt 2 4 m s2 2 General safety instructions Machine noise information regulation 3 GSGV the noise pressure level at the place of work can exceed 85 dB A In such cases the operator will require noise protection e g wearing of ear protectors Attention Noise protection Please observe the local regulations when operating your device Interference suppressed in accordance with EN 55014 EN 61000 3 2 95 EN 61000 3 3 95 We reserve the right to make changes to the technical specifications The hedge trimmers are constructed in line with th2. a length of more than 30m reduce the machine s output 6 Instructions for use of the equipment Do not use the trimmer in rain or for cutting wet hedges Check the hedge trimmer flex and its connections before each and every use for visible signs of damage disconnect the power plug Do not use a faulty flex Gloves Protective gloves must be worn when using the hedge trimmer 7 Switching the hedge shears on off Fig 3 When switching the hedge shears on take a safe stand These hedge shears have a two hand safety switch To switch the hedge shears on the bar switch in the handle A and the grip switch of the bow type handle B must be pushed down To switch the device off let go of both switches The motor already stops if one of the two switches is released GB 2 8 Adjusting the turning handle To facilitate your work the hedgetrimmer model 600HD 60EL are equipped with a turning rear handle that can be set in 3 different positions right left and normal The purpose of this mechanism is that especially for cutting in vertical direction the hedge shears can be held in their ergonomically most favourable position whereby an early fatigue of the user is avoided Please proceed as follows to change the position of the handle Release switch A Pull back the locking pin B Fig 5 The handle is now unlocked and can be turned to the desired position Fig 6 7 In the desired end position the pin locks back into
3. blades will stop due to safety reasons exactly under the cover rail in order to reduce the risk of injuries during transport Impact protector Fig 11 The extended guide rail prevents unpleasant shocks blade recoil being transmitted to the operator due to impact with solid objects wall ground etc Gear protection feature If solid objecst are caught in the cutting blade and jam the motor switch off the machine at once disconnect the power plug from the power socket remove the object and continue with the work The equipment is also fitted with an overload cutout which protects the gears against mechanical damage in the event of blade jams 12 Storing the trimmer after use The hedge shears must be stored such that there is no danger of injuries being caused to persons by the cutting blades Important note The shearing blades should be cleaned after each use see also Section 9 Maintenance This will considerably increase the service life of the device Please use a lubricator that is not harmful to the environ ment e g our service spray Then put the shears in their case with the cutting blades first 13 Repair service Repairs to electric power tools should only be carried out by specialist electrical personnnel GB 3 EC Declaration of Conformity according to EU Guideline of Machines 98 37 EG We Husqvarna Skog amp Tr dgard SE 561 82 Huskvama Sverige declare under our sole responsibili
4. relief of the hedge shears housing In doing so one must not push the two parts of the bow type handle together To fix the bow type handle the two included screws must be screwed into the threadings in the housing through the openings of the handle and fastened tightly Handguard Fig 2 Slide the handguard onto the handguard plate at the front side of the housing until it effectively locks into place Power connection The machine can only be connected to a single phase a c current connection The machine is protectively insulated in accordance with classification Il of VDE 0740 and can therefore be connected to sockets with out earth connections Before using the machine ensure that the mains current agrees with the operating voltage data on the machine s identification plate Power Circuit Breaker Machines which will be used in different outside locations must be connected to a Power Circuit Breaker Securing the power supply cable Fig 3 Only use cables extension flex that are approved for outdoor use The cable diameter must be equal to or bigger than 1 5mm for cable lengths up to 75m Put the coupling of the extension flex onto the shears plug For strain relief stick a loop of the extension flex through the opening in the handle and put it onto the strain relief hook After finishing work slide the loop ahead over the hook and pull it back through the handle opening Pull the mains plug Extension flexes with
5. by a service station designated by the manufacturer as special tools are necessary Equipment which will be used in different outside loca tions should be connected via residual current operated current breakers 16 Ensure that the equipment is stored safely after use in such a way that the blade cannot be touched 17 When using the equipment hold it securely with both hands stand firmly and ensure that you have sufficient working space There should be no people animals or objects within the working area Select the cutting height so that the blade does not make contact with the ground and you can operate the equipment from a secure position 18 Take care when transporting the equipment only with blade cover 19 For initial use of the hedge trimmer we would recommend that in addition to reading the operating instructions you also seek a practical demonstration from an expert 20 Always ensure that all protective devices and handles are properly fitted Never attempt to use an incomplete machine 21 The use of the hedgetrimmer is to be avoided if other persons above all children are within the working area 22 Familiarize yourself with the working area and pay attention to possible dangers which you might not be able to hear due to the noise of the machine 5 Before use Mounting the bow type handle Fig 1 The bow type handle must be pulled over the blade system from below as shown in Fig 1 and then set into the
6. e latest regulations in accordance with DIN EN 50144 1and DIN EN 50144 2 15 and conform fully to equipment safety law regulations General safety instruction Usage of hedge trimmer always involves a risk of accidents therefore please observe the relevant accident prevention instructions The machine has been constructed according to the latest technology and in accordance with the recog nised technical safety regulations Nevertheless use of the machine can involve risks to the user or third persons and can cause damage to the machine or other objects Attention Using electric power tools you must observe following fundamental safety instructions to protect yourself against electric shock against danger of injuries and danger of fire Read all these instructions before using the hedge trimmer and observe them Keep these safety instructions at a safe place Use the machine in a safety conscious manner for suitable applications in a technically perfect condition only and with due regard to the operating instructions Immediately rectify or have rectified any faults which could adversely affect safety This machine may cause serious injuries Please read the instruction manual carefully as to the correct handling the preparations the maintenance and the proper use of the hedgetrimmer Familiarize your self with the machine before the first use and also have yourself introduced to practical use of the machine 3 Applicatio
7. eature of the blades Changing of the blades should therefore only be carried out at a specialist workshop 10 Holding the hedge trimmer when in use Fig 10 This equipment will enable you to cut or trim bushes and hedges easily and comfortably Trimming of hedges Young shoots are best cut in a scythe move ment Older and stronger hedges are best cut in a sawing movement Branches which are too thick for the hedge trimmer should be cut with a saw Sides of hedges should be cut upwards in a taper In order to achieve an even height Fix a guide line at the required height Cut evenly over this guide line 11 Optimum safety The 5 special features two hand safety switch quick blade stop protective cover blade safety rail and impact protector are fitted to provide the hedge trimmer with optimum safety features Two hand safety switch Fig 4 To switch on the hedge trimmer one of the switch bars on the hand grip A or B and the switch on the bow type handle C must be held down If one of the switches is released the shearing blades will stop after ca 0 2 seconds Quick blade stop In order to avoid injuries through cuts the blade will stop in max 0 2 sec when one of the two switches is released Blade safety rail Fig 9 The cutting blade set back from the blade housing reduces the risk of injuries due to unintentional body contact As soon as the hedge trimmer is switched off the sharp cutting
8. ice with water Do not use any high pressure cleaning devices or steam jet devices for cleaning GB 1 8 Carry the trimmer by the handles provided and keep hands away from the cutting blades 9 In line with agricultural Trade Association Regulations only persons over the age of 17 may work on their own with electric hedge trimmers Use is permitted for persons over 16 years if the work is carried out under the supervision of adults 10 We would recommend that safety clothing is worn during the work and that eyes ears hair hands and feet are fully protected Protective gloves should also be worn 11 Ensure that the motor of your hedge shears can not be switched on by mistake when you put it A down after work or when you are going to clean the device Never forget to unplug the mains supply 12 Check the cutting unit regularly for damage and if damage is discovered the cutting unit should be properly repaired 13 Be aware of your responsibility as user towards third parties in the working area 14 The trimmer must be properly checked and serviced If the blades get damaged they should only be exchanged in pairs In the event of damage from impact specialist s inspection is essential 15 Only use extension leads which have been authorised for outside use These flexes must not be lighter than PVC covered flex conforming to 227 IEC 53 They must be water spray pro tected Damaged cables of this unit are only to be replaced
9. n The machine is only intended for trimming hedges Use for any other purpose constitutes inappropriate use The manufacturer supplier is not liable for any injury and or damage arising from inappropriate use This risk is the sole responsibility of the user Appropriate use of the machine also includes adherence to the operating instructions and compliance with the servicing and maintenance instructions Always keep the instruction manual close at hand during operation 4 Safety instruction 1 Always disconnect the plug from the mains A socket before carrying out any work on the equipment before cleaning and before moving the equipment 2 The use of hedge trimmers involves certain risks Attention Danger Rotating machinery 3 The hedge trimmer should always be held with both hands 4 Before using the equipment clear the working area of any foreign objects and be aware of foreign objects during operation of the machine If the machine becomes jammed e g by thick branches switch off and disconnect the machine from the mains socket before investigating and rectifying the cause of the jam Take special care when switching the machine on again 5 Check the flex and all connections for any visible faults before using the machine plug discon nected Do not use a faulty flex 6 Keep the flex away from the cutting area 7 Do not use the trimmer in wet weather and do not use it to cut wet hedges Do not wash down the dev
10. place and securing the handle and avoiding an accidental change of the position Please bear in mind that the locking pin B can only be pulled back when the switch A is not activated held down Make sure that the locking pin locks into place again after repositioning the turning handle Only then the switch can be activated anew 9 Maintenance Always disconnect the plug from the power socket before commencing any work on the machine Important Always clean and oil the blades after prolonged use of the hedge trimmer This will greatly affect the life of the equipment Damaged cutting units must be properly repaired immediately Clean the shearing blades with a dry cloth or in case of heavier dirt with a brush Attention Danger of injury Oiling of the blades should ideally be carried out using an environmentally friendly lubricant Fig 8 Sharpening of the blades The blades generally do not need servicing and do not require resharpening if used correctly In order to prevent injuries caused by the blades when not in use the sharpened cutting blade should be covered by the blade cover Fig 9 The blades cannot be sharpened by the user without opening the equipment and the safety mechanism Resharpening of the blades can therefore only be carried out at a specialist workshop Changing the blades Only correct installation of the blades will guarantee problem free operation and function of the above mentioned safety f
11. ty that the hedge trimmer 500HD 56EL 600HD 60EL to which this declaration relates correspond to the relevant basic safety and health requirements of Directives 89 336 EEC EMV Guideline 73 23 EEC Low Voltage Guideline 89 37 EG Guideline of Machines and 2000 14 EC noise directive For the relevant implementation of the safety and health requirements mentioned in the Directives the following standards and or technical specification s have been respected EN 55014 1 EN 55014 2 EN 50144 HD 400 1 HD 400 3 EN 61000 3 2 1995 EN 61000 3 3 1995 EN 774 measured acoustic capacity level 95 dB A Testing laboratory DPLF D 34114 Kassel guaranteed acoustic capacity level 97 dB A Conformity assessment method to annexe VI Directive 2000 14 EC Huskvarna 12 12 2002 Bo Andr asson Technical Director ss OA hare Warranty For this electric tool the company provides the end user independently from the retailer s obligations resulting from the purchasing contract with the following warranties The warranty period is 24 months beginning from the hand over of the device which has to be proved by the original purchasing document For commercial use and use for rent the warranty period is reduced to 12 months Wearing parts and defects caused by the use of not fitting accessories repair with parts that are no original parts of the manufacturer use of force strokes and breaking as well as mischievous overloading of the motor are excl
12. uded from this warranty Warranty replacement does only include defective parts not complete devices Warranty repair shall exclusively be carried out by authorized service partners or by the company s customer service In the case of any intervention of not authorized personnel the warranty will be held void All postage or delivery costs as well as any other subsequent expenses will be borne by the customer H Husqvarna were bosqrar com 114 01 71 20
Download Pdf Manuals
Related Search