Goodman Mfg AVPTC183014 Air Conditioner User Manual
Contents
1. TECHNICAL MANUAL AVPTC Air Handlers Refer to Service Manual RS6200006 for installation operation amp troubleshooting information All safety information must be followed as provided in the Service Manual Refer to the appropriate Parts Catalog for part number information Models listed on page 3 This manual is to be used by qualified professionally trained HVAC technicians only Goodman RT6121001r2 does not assume any responsibility for property damage or personal injury due to improper January 2011 service procedures or services performed by an unqualified person ry Copyright 2010 2011 Goodman Manufacturing Company L P PRODUCT IDENTIFICATION The model number is used for positive identification of component parts used in manufacturing Please use this number when requesting service or parts information EXPANSION DEVICE F Flowrater T TXV Expansion Device MINOR REVISION MAJOR REVISION REFRIGERANT CHARGE 4 R 410A PRODUCT TYPE A Air Handler CABINET FINISH U Unpainted P Painted N Uncased APPLICATION EXPANSION C Ceiling Mount PSC Motor DEVICE ELECTRICAL D Downflow PSC Motor C 4 Wire 1 208 230V 1ph 60Hz E Multi Position Varible Speed Motor Communicating R Multi Position PSC Motor Ready S Energy Efficient Motor Multi Position PSC Motor T Coated Coils V Variable Speed ECM Motor NOMINAL CAPACITY RANGE Multi Positi2. 2 FOR 208 VAC PK PINK LOW VOLTAGE FIELD OPERATION BR BROWN 2 MANUFACTURER S SPECIFIED REPLACEMENT PARTS MUST BE USED WH WHITE HI VOLTAGE 230V PL BLUE HI VOLTAGE FIELD 3 IF ANY OF THE ORIGINAL WIRES AS SUPPLIED WITH THIS UNIT GY GRAY JUNCTION MUST BE REPLACED IT MUST BE REPLACED WITH WIRING RD RED MATERIAL HAVING A TEMPERATURE RATING OF AT LEAST 105 C TERMINAL USE COPPER CONDUCTORS ONLY YL YELLOW INTERNALTO 4 UNIT MUST BE PERMANENTLY GROUNDED AND CONFORM TO N E C AND ORORANGE INTEGRATED CONTROL LOCAL CODES VT VIOLET EQUIPMENT GND 5 TO RECALL THE LAST 6 FAULTS MOST RECENT TO LEAST RECENT GN GREEN FIELD GND d WARNING DEPRESS SWITCH FOR MORE THAN 2 SECONDS WHILE IN STANDBY N BK BLACK THERMOSTAT INPUTS 6 BIAS AND TERM DIP SWITCHES MUST BE IN ON POSITION RED FIELD SPLICE STATUS LED PROVIDES NETWORK STATUS GREEN RX LED INDICATES NETWORK TRAFFIC USE LEARN BUTTON TO RESET NETWORK RESISTER 7 DISCARD CONNECTOR PL1 WHEN INSTALLING OPTIONAL HEAT KIT OVERCURRENT PROT DEVICE 0140A00039 REV C PLUG CONNECTION Wiring is subject to change Always refer to the wiring diagram on the unit for the most up to date wiring 10
3. AVPTC 3 AVPTC183016 AVPTC313716 AVPTC426016 BlowerWheel Diameter Width Ps 59 1058 Lineset Connection Size J ___ Liquid Suction Electrical Data o BlowerMotor T FA 890 520 690 BLOWER PERFORMANCE DATA Speed Selection Dip Switches Electric Heat Airflow and Temperature Rise Table a Switches Switches Switches 2 232101 we 1 2 s sis 5 ooo or or e Jo jor ov e for on or e os for or Hi ERE crm m 5 30 550 605 00 shown the emergency heat heat only e nme in either legacy mode operation or communicating mode operation SEC a setairflow Select model and desired Low Stage High Stage high stage cooling airflow Determine the cooresponding tap Cool Cool BC orD Se I switches 1and 2 to the appropriate ON OFF TATEN 2 Select model and installed electric 630 heater size Set switches 9 10 and 11 to the appropriate 840 ONOFF positions 3 Select the airflow adjustment factor tap Aand D are 096 Tap B is 0 Tap C 1096 Set dip switches 3 AVPTC 183014 1036 and 4 to the appropriate ON OFF positions 1232 610 825 1040 1237 1210 1408 AVPTC 426014 562 804 NOTE Airflow data shown applies to legacy mode operation only For a fully communicatin
4. When this productis installed in the downflow installation in an unconditioned space remove the horizontal drain pan and install the following insulation kit 1830 DP136 42 20 See following chart for the correct DPIH kit 1830 DPIH36 42 3137 4260 DPIH48 61 AVPTC is a multi position variable speed air handler and is This kit is used to prevent sweating on the vertical drain pan U EONAR T TURS TAE VOK n ECM motor and is compatible with heat pumps and variable capacity cooling applications See note below 3137 4260 0 148 61 20 preventthe horizontal drain pan from sweating in high humidity applications it is recommended that a DPIH jd m din En n o deo NOTE Factory sealed to achieve a 2 or less leakage rate AON KE TE Re d at 1 0 water gauge external duct static pressure purchased separately Complies with the Factory sealed Air Handling Credit as listed inthe 2001 Florida Building Code Chapter 13 Section 610 2 A 2 1 PRODUCT DIMENSIONS AVPTC lt p 1 1 2 54 cm C 2 54 cm id gt 2 54 PLASTIC BREAKER LOGO SUCTION LINE LIQUID LINE gt 4 INLET TUBE 1 3 16 2 7 8 7 3 cm gt 3 0 cm INLET RIGHT SIDE VIEW FRONT VIEW HE EOS GE EC KCN EUN o AVPTO420014 PRODUCT SPECIFICATIONS
5. AS 2 mi BIAS 3 mj TERM Indoor Unit BIAS and TERMINATION Dipswitches WIRING DIAGRAMS AVPTC EN JOQ OOQ oo OCC 2C QOO 2C Ta THREE 3 ELEMENT Rows _ NOTE WHEN INSTALLING HEATER KIT ENSURE SPEED TAP DOES NOT EXCEED MINIMUM BLOWER SPEED MBS SPECIFIED FOR THE AIRHANDLER HEAT ER KIT COMBINATION ON THIS UNIT S S amp R PLATE AFTER INSTALLING OPTIONAL HEAT KIT MARK AN X IN THE PROVIDED ABOVE MARK ACCORDING TO NUMBER OF HEATER ELEMENT ROWS INSTALLED NO MARK INDICATES NO HEAT KIT INSTALLED 40 VATRANSFORMER SEE NOTE 1 230 VAC 208 VAC DISCONNECT 4 CIRCUIT HEATER INDOOR CONNECTOR CIRCULATOR BLWR P CFMLED p SEE DIAGNOST O Not 5 3A 208 230 VAC a8 29 lt 8 m uz Yow 9 DIP SWITCHES we ee yi Qo 41 lt G STATUS am LED RX LED H SEE NOTE 6 YOLOANNOO MOLON R UNIT MULTIPLE POWER SOURCES MAY BE PRESENT FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE PERSONAL INJURY OR DEATH o rI 2 l 2 o z 5 gt tc o u ul m o a lt o o o a SNOILOANNOO 1V1SOWH3HL A vc i lt H gt Sg r 2 TWO STAGE INTEGRATED CONTROL MODULE 1 SNO LINWOOD 1V LSOWH3H L Avc COLOR CODES LOW VOLTAGE 24V NOTES 1 PLACE RED WIRE ON TRANSFORMER TERMINAL
6. ING The unit MUST have an uninterrupted unbroken electrical ground to minimize the possibility of per sonal injury if an electrical fault should occur The electrical ground circuit may consist of an appro priately sized electrical wire connecting the ground lug in the unit control box to the building electrical service panel Other methods of ground ing are permitted if performed in accordance with the National Electric Code NEC American Na tional Standards Institute ANSI National Fire Protection Association NFPA 70 and local state codes In Canada electrical grounding is to be in accordance with the Canadian Electric Code CSA C22 1 Failure to observe this warning can result in electrical shock that can cause personal injury or death A WARNING If this appliance is installed in an enclosed area such as a garage or utility room with any carbon monoxide CO producing appliance i e automo bile furnace water heaters etc ensure the area is properly ventilated AIR HANDLERS See Air Handler Specification Sheet for Proper Combinations ALL AIR HANDLERS USE DIRECT DRIVE MO TORS POWER SUPPLY IS 220 240 V 60 HZ 1 PHASE Installation Before installing this appliance insure that it is properly sized and adequate power is available This appliance can be installed in the vertical position with out modification The horizontal left and downflow positions require product modification and instr
7. g system please see the outdoor unit s installation instructions for cooling and heat pump airflow data See ComfortNet System Airflow Consideration section for details To set Comfort Mode Select desired Comfort Mode profile Eee profiles above Set switches 5 and 6 to the approriate AVPTC 33714 ON OFF positions gt O G G gt gt 0140400048 REV A Heat Kit Selection MODELS AVPTC183014A AVPTC313714 AVPTC42601 4A HKR IHKFRO Bem x x x Wes x gt in _ T gt ene T C Revision level that may or may not be designated C Circuit breaker option 1 For units operating in Legacy mode use dip switches 9 ON 10 OFF 11 OFF to obtain 1000 CFM or 9 OFF 10 ON 11 ON to obtain 1200 CFM For units operating in Communicating mode use dip switch 8 kW to obtain 1000 CFM or 10 kW Htr to obtain 1200 CFM 2 This heater kit can only be used for 1000 or higher applications 3 This heater kit can only be used for 1200 CFM or higher applications BLOWER PERFORMANCE DATA Outdoor Data Line Indoor Control Control Voltages Vdc TERM TERM BIAS Dipswitches Dipswitch ON on ze zz 05 For per s 9s ON OFF ON OFF ON I Fees N TERM1 TERM Termination dipswitches at outdoor unit See installation instructions with CT compatiable outdoor unit OFF ON 1 m BI
8. on amp Downflow Applications 1830 1 1 2 2 1 2 Tons 3137 2 1 2 3 Tons 4260 3 1 2 5 Tons All Airhandlers use DIRECT DRIVE MOTORS Power supply is AC 208 230v 60 hz 1 phase HIGH VOLTAGE A WARNING Disconnect ALL power before servicing or installing this unit Multiple power sources may be present Failure to do so may cause property damage personal injury or death Installation and repair of this unit l A WARNING S A RA AA a dg 4 WARNING should be performed ONLY by in arising from improper service or service procedures If dividuals meeting at a minimum you install or perform service on this unit you assume the requirements of an entry level t chnician responsibility for any personal injury or property damage Hed by Air Conditioning Heating and Refrigeration which may result Many jurisdictions require a license to Institute AHRI Attempting to instan Or repair this install or service heating and air conditioning equipment without such background may result product damage personal injury or death PRODUCT IDENTIFICATION The model number is used for positive identification of component parts used in manufacturing Please use this number when requesting service or parts information AVPTC183014 AVPTC313714 AVPTC426014 A WARNING The United States Environmental Protection Agency EPA has issued various regulations re garding the introduction and dispo
9. sal of refrigerants introduced into this unit Failure to follow these regulations may harm the environment and can lead to the imposition of substantial fines These regulations may vary by jurisdiction Should questions arise contact your local EPA office Do not connect or use any device WARNING frat 1s nor design ceri d WARNING To prevent the of property A that is not design certified by 4 WARNING damage personal injury or death 1 Goodman for use with this unit do not store combustible materials or use gasoline or Serlous property damage personal injury reduced unit other flammable liquids or vapors in the vicinity of this performance and or hazardous conditions may result appliance from the use of such non approved devices PRODUCT DESIGN WARNING When installing or servicing this equipment safety clothing including hand and eye protection is strongly advised If installing this equipment in an area that has special safety requirements hard hats etc observe these requirements To protect the unit when brazing close to the painted surfaces the use of a quenching cloth is strongly advised to prevent scorching or marring of the equipment fin ish A warnine HIGH VOLTAGE Disconnect ALL power before servicing or installling this unit Multiple power sources may be present Failure to do so may cause property damage personal injury or death WARN
10. uctions for these field conversions can be found inthe AVPTC installation instruction manual This product is designed for zero inches 0 inches clear ance however adequate access for service or replacement must be considered without removing permanent structure This unit can be installed on a platform when deemed neces sary In an attic installation a secondary drain pan must be pro vided by the installer and placed under the entire unit with a separate drain line properly sloped and terminated in an area visible to the owner This secondary drain pan is required in the event that there is a leak or main drain blockage Closed cell insulation should be applied to the drain lines in uncondi tioned spaces where sweating may occur Appliances installed in garages warehouses or other areas where they may be subjected to mechanical damage must be suitably guarded against such damage by installing be hind protective barriers being elevated or located out of the normal path of vehicles When installed on a base the base must also be protected by similar means Heating and cooling equipment located in garages which may generate a glow spark or flame capable of igniting flam mable vapors must be installed with the ignition source at least 18 46cm above the floor level When more than one appliance is installed in a building it shall be permanently identified as to the area or space ser viced by the equipment PRODUCT DESIGN
Download Pdf Manuals
Related Search