GE PVWS930 Range User Manual
Contents
1. GB 8 Telephone SCART lead RF lead modem cable License Owner s manual agrement TRF TYFPFTTTTTTTT SCART socket e Certain outdoor antennas are pointed at an analogue slave transmitter The roof antenna should be pointed at a digital TV transmitter e It is not always advisable to position the antenna as high as possible If problems arise experiment with different antenna heights The same applies to analogue transmissions 2 Indoor or window mounted antenna This type of antenna may be enough if the reception conditions are very good If an indoor antenna is used please note the fol lowing e Use an antenna for UHF channels 21 69 such as a directional antenna e The directional antenna should have horizontal polarisation oreferably rotatable e Place the antenna by the window and point it towards the TV transmitter if possible e An antenna with an amplifier is recommended as It may pro vide a stronger signal e Attenuation of the TV signal varies according to the building material The signal penetrates thick stone or concrete walls poorly A window improves reception However a wooden building is no barrier to digital TV signals About antennas Radio and TV signals can be blocked by buildings mountains and the terrain If the receiver is located in a depression in the ground behind a mountain or in a concrete building the quality of2. Owner s Manual MEDIAMASTER 9820 T NOKIA CONNECTING PEOPLE MEDIAMASTER 9820 T Contents GENERAL OPERATION OF THE MEDIAMASTER FOR YOUR SAFETY REMOTE CONTROL Rear Panel Front Panel ABOUT THE SMARTCARD Subscription TV Services with a Smartcard Viaccess INSTALLATION OF THE MEDIAMASTER Preparing the Remote Control Connecting to the TV aerial Connecting the Mediamaster Connecting the Mediamaster to the TV Connecting a TV and VCR Connecting an Analogue Satellite Receiver and VCR Connecting a HiFi system Connecting to the telephone wall socket Tuning Procedure when RF Connections are Used First time installation General Information The Welcome Menu Language Channel Search Channel Search Progress Viewing Mode General Information Programme Information The i Information Button Guide NO O O1 PP A List of TV or Radio Channels Options Green Button TV Release 0 Video Recording The TEXT Button Teletext Main Menu General Information Channels Edit Channels Guide System Configuration Channel Search Antenna Configuration TV Settings Modem Configuration Receiver Upgrade Reinstall User Preferences Language Preferences Parental Control Change access code Appearance Preferences System Information Conditional Access GLOSSARY OF TERMS PROBLEM SOLVING FRONT PANEL DISPLAY TECHNICAL SPECIFICATIONS MENUS SCREEN STRUCTURE Nokia Multimedia Terminals operates a poli
3. and later unlock channels in any of the lists in order to prevent e g your children from watching Select the channel you want to lock and press OK Repeat the procedure for each channel you want to lock When you lock a channel in any list the channel will automatically be locked in all other lists A locked channel will be marked with a padlock symbol When watching TV you will be asked to enter your access code before you can watch a locked channel Rename Channels Within any of your favourite lists you can rename the channels Mark the channel you want to rename and press OK The Re name dialogue box will then appear and let you modify the ex isting name To enter the new name please follow the instructions under the headline How to give a specific name on page 20 When you have changed a channel name the new name will ap pear in all lists where the channel is included SELECT CHANNELS Abr Add channel SVT1 to favourite list Abt by pressing OF Exit f Back to menu mes add LOCK CHANNELS All Tw Y Markndtet Unlock channel SWT by pressing OF Exit Back to menu paa Unlock fok RENAME CHANNELS All TW Rename channel SWT by pressing OE exit 8 Back to menu fren Renarne fak GB 21 Rearrange Channels From here you can arrange the sequence for the channels within your favourite lists e With gt mark the channel you want to move to a new
4. programmes and events CA module A device for the decoding of scrambled signals Common Interface Describes a DVB standard hardware and software archi tecture for Conditional Access systems DVB The Digital Video Broadcast group was created to estab lish a technical framework for the introduction of digital video broadcasting systems EPG Electronic Programme Guide A software that enables viewers to navigate easily among the large number of channels provided by digital technology in order to se lect the service they desire Mediamaster A unit that converts the digital terristrial signals into au dio and video signals The audio and video signal can be sent to the TV set either via SCART or via RF modulator output MHz The prefix mega means million and Hertz means cycles per second MPEG Moving Picture Experts Group Body established by the International Standards Organisation to provide the ba sis for a picture coding and compression system Network A number of digital channels transmitted from one source Grouped under separate headings in the channel list OFDM Orthogonal Frequency Division Multiplexing Modulation method used in digital terrestrial networks in Europe PCMCIA Personal Computer Memory Card International Associa tion The Common Interface slot follows this standard Parental control A feature that allows parents to lock programmes that they consider unsuitable for children A l
5. 10 meters 380 x 240 x 65 mm 1 8 kg approx AUX Audio out right ch Audio in right ch Audio out left ch Audio ground RGB blue ground Audio in left ch RGB blue signal in Switch voltage in RGB green ground Connect to pin 10 in AUX scart RGB green signal out RGB green signal in RGB red ground Fast blank ground RGB red signal in Fast blanking in Video out ground Video in ground Video out Video in Ground casing MENUS SCREEN STRUCTURE First time installation Language Channel Search Channel Search Progress Welcome 1 Svenska 1 Automatic Search DE Lae 3 5i ates 2 Suomi 2 Manual Search Bro ae icture F lt INotek TV 24 Kommande kanal i TV4 Kommande kanal Main Menu User Preferences p 1 Language Preferences 2 Parental Control 3 Appearance Preferences j Language Preferences 1 Menu Language 2 Main Audio Language 3 Alternative Audio Language 4 Subtitles 7 S 5 Main Subtitle Language Channels 6 Alternative Subtitle Language a ATV gt Viaccess Embedded C F ANAE a Smart Card Code
6. 9 pin D sub male RS232 max 115 2 kbit s Data carrier detect not connected Receive data Transmit data Data terminal ready Set to high Signal ground Data set ready not connected Ready to send Clear to send Ring indicator not connected TELEPHONE Return channel Telephone line Connector Protocol GB 32 Modular jack 6 pin V32 bis 14400 baud Conditional access system Embedded Viaccess and PCMCIA one interface for a Common Interface CA module DVB Standard Smart Card Interface Interface for one card according to ISO 7816 Supports embedded descrambler Viaccess Front panel 4x7 segment numeric LED display Buttons V A lt gt OK EXIT MENU General data Article code The model code variant and serial number are located on a label on the underside of the housing Supply voltage Power consumption max Power consumption in standby Operating temperature Storage temperature Humidity Operating distance for remote control Dimensions wxd xh Weight SCART sockets TV 1 Audio out right ch 2 3 Audio out left ch 4 Audio ground 5 RGB blue ground 6 7 RGB blue signal out 8 Switch voltage out 9 RGB green ground 12 RGB red ground Fast blank ground RGB red signal out 16 Fast blanking out Video out ground 18 19 Video out 20 21 Ground casing 230 VAC 415 50 60 Hz 15 W 5 5 W 5 C to 45 C 40 C to 65 C 25 to 90 rel humidity max
7. Connect an RF lead from the RF output on the satellite receiver to the RF input socket on the VCR Connect an RF lead from the TV VCR output on the Mediamaster to the RF input socket on the satellite receiver Connect the TV aerial to the TV AERIAL input socket on the Mediamaster Connect the coaxial cable between the LNB and the LNB socket on the satellite analogue digital receiver Both the VCR and the analogue satellite receiver must be tuned to different UHF channels than the Mediamaster when using RF connectors Media master LNB The analogue satellite receiver must be switched to OFF standby when you want to watch digital terrestrial chan nels from the Mediamaster Satellite receiver Connecting a HiFi system Connect an RCA Cinch stereo cable from the AUDIO L R sockets on the Mediamaster to the LINE AUX SPARE or EXTRA Input sockets on your HiFi system If available you can connect an RCA Cinch single cable from the DIGITAL AUDIO socket on the Mediamaster to your HiFi or Dolby Pro Logic system Note To avoid interference you must use a screened audio cable Connecting to the telephone wall socket TELEPHONE sockets on the Mediamaster to a telephone socket GB 11 Tuning Procedure when RF Connections are Used This procedure is necessary only if your Mediamaster is con nec
8. Search Progress Menu you can start searching for terrestrial digital channels offered by the TV transmitter for which your antenna has been configured All TV channels found will be listed in a column on the screen Please note that the search procedure may take a few minutes When the search procedure has ended the screen will show how many TV channels have been found Press OK and continue to press OK until the channel number 1 shows on the front panel display You will see the corresponding programme on the IV screen GB 14 CHANNEL SEARCH Marknatet Manual Search Perform automatic search te find channels Exit Go back ran select I Gunman OO Mode Guard Interval afi SET a es San Network Search Yes Select WHF channel using the number keys CHANNEL SEARCH PROGRESS Lat 730 MHz CH53 8k V8 TY Channels Kommande kanal NollEttan TWS Kammande karm Twa Kommande kanal Kommande kanal Twa TVG Senda Guide TWE eWorld Kommande kanal aly Kommanda kanal Searching t new TY channels found VIEWING MODE General Information The following describes the basic functions of your Mediamaster while watching terrestrial digital TV Some of the functions described here are dependent on the Service Provider and can only be used if they are included in the transmitted programme information Please note that during the Channel Search procedure the Mediamaster may do
9. Teracom_Linkaping Network Id 12705 Orig Network cb 8945 Transport Stream Id 1049 Frequency 522 0 MHz t 9 PE AET Guard interval 1 8 ee 10 Peer EN Mode 8K METE a ear Modulation QAM 64 Service lo 1010 Digital Television Service I d ff l OPTIONS x Camera 1 F a Subtitle language 3 Format oe options GB 17 VIEWING MODE Format If you have a TV set with a 4 3 picture format and the transmis sion is in 16 9 you can select Fullscreen or Letterbox to change display format Fullscreen will fill up the screen vertically but cut off some infor mation from the left and right sides of the picture Letterbox will give a complete picture but leave black areas at the top and bottom TV Release 0 With the 0 button you can toggle between digital terrestrial TV analogue terrestrial TV video the video must be on This is only valid if the units are connected via SCART cables and not by a RF connection Video Recording Please note that during the recording of a programme every thing shown on the screen will be registered For example if you call up a menu from the Mediamaster on the screen the menu will be recorded The TEXT Button Teletext e Pressing the TEXT button will open a Teletext page if Teletext is transmitted Select teletext pages with the numeric buttons on the remote control e You can also quickly step to the different page alternatives shown in any page b
10. arrow buttons to move a page at a time up and down When a line is highlighted you can get more information about this programme by pressing the i button By pressing GUIDE in TV mode you get access to the EPG from Senda if this information is transmitted in the signal GB 16 a 22 00 ama 720 min SAT2000 1000 22 00 SAT2000 TAD min a Pl dei DS M 22 00 eee 720 min SATION 10 00 22500 SAT 2000 SAT2000 720 min Shaw current 2200 720 min SATIOOO 7 00 200 SAT2000 720 Poin GUIDE 3 3 2230 1600 SWT 14 SVT 10 00 10 00 Kop OD skivor se p musikvideos vade Exit C Select this Y VIEWING MODE List of TV Channels At the channel search procedure a Channel lists named Chan nels containing all channels are created In the Channels list scrambled channels are marked with a pic ture of a Smartcard if this information is transmitted in the sig nal and locked channels are marked with a padlock If you have performed a new channel search the new channels found will be marked with a star in the Channels list When viewing TV you can access the Channel List by pressing OK The channel list can also be selected from the main menu At the top of the menu you will see the name of the list The cur rent list is the one In which the channel you are watching right now is located e f the list contains a large number of channel
11. highlighting an option to display the within a menu or channel list scrolling through channels GB 6 ABOUT THE SMARTCARD AND CA MODULE To be able to receive terrestrial scrambled digital channels you will need a Smartcard from the Service Provider Senda Senda is the the programme distributor Please note that a Smartcard may only be valid for a single Serv ice Provider and due to this a specific range of channels The Smartcard and the CA module may also provide access to special menus not described in this manual If so please follow the instructions from the Service Provider Note The Smartcard is distributed by your Service Provider After inserting the card leave it in the slot permanently Do not remove it again unless your Service Provider asks you to do so This is important because if your Service Provider wants to download new information to the Smartcard the card has to be in the slot Subscription TV Services with a Smartcard Viaccess Only for subscription TV services coded with the Viaccess CA system e Insert your Smartcard fully into the left slot behind the lid of the front panel of the Mediamaster The gold chip should face downwards and inwards Note The gold chip must be on the underside and in wards of the smartcard GB 7 INSTALLATION OF THE MEDIAMASTER The box for your Mediamaster should contain the following items e the Mediamaster e aremote control with 2
12. if it is used elsewhere Position of the RGB output Adjust the horizontal position of the TV picture with the lt gt but tons The TV signal see above must be set to RGB for this function to work Modem Configuration When you connect the Mediamaster to the Telephone net via the built in modem specify the necessary settings in this menu Pulse or tone Select the alternative which is valid for your sys tem If you are unsure contact your telephone distributor Prefix digit If the connection goes via a switchboard select the digit which opens the line Digits after pause Possibility to add a pause between the coun try prefix and the ordinary number by long distance calls This function is not necessary by modern switchboards In the future it might be possible to perform electronic transac tions such as Pay Per View PPV Home Shopping Programme voting and Banking etc via the built in modem GB 24 TV SETTINGS ep TV Signal RGE E RF Channel l 43 CRE Modulator Type Select the fonmat of your TV screen ent Go back cx confirm 3 The RF channel number will be in dicated on the front display of the Mediamaster MODEM CONFIGURATION E Digits after pause Select pulse or tone dialling exit Go back re confirm G3 Receiver Upgrade In order to keep the Mediamaster up to date it will be possible to download new versions
13. it e Toggle between capital and lowercase letters with the blue button Rename list From here you can give an existing lista new name Use the ar row buttons the same way as when you created the list Rearrange lists If you have created several Favourite lists you can determine the sequence in which the lists will appear Delete list If you want to delete a Favourite list completely select the list and press OK GB 20 CREATE TV LIST ui lt Guit gt 6 7 z exit Cancel pa contin Gy Select Channels From this menu you add and remove the channels in your Favour ite Lists You use the All TV list as basis to select the channels from A channel is added or removed by pressing the OK button The square to the right on a line will be empty for removed channels and will contain an x for added channels e If you have a Favourite list that contains several satellites and networks you can close the one s you are not going to work with You open close a satellite or network by first marking it and then pressing 9 A closed satellite network is indicated with on the line e Move to desired channel s with w a double arrows or the nu meric buttons and add remove them by pressing OK e When you are ready confirm the selections and leave the menu by pressing BACK or EXIT Lock Channels To get to this menu you first have to enter your access code From here you can lock
14. mode The system is connected by RF leads and the TV is not set to the channel tuned for digital terrestrial TY What to do Check that the mains cable is plugged in to the power socket Press the standby button or any number button to bring the Mediamaster out of standby Check if the aerial works for analouge reception If your system is connected by SCART leads press 0 If this does not work set the TV to its appropri ate AV input If your system is connected only by RF leads set your TV to that channel you have tuned for digital terrestrial TV Check SCART connections making sure leads are firmly pushed into the sockets Iry manually selecting the AV EXT channel on your TV Check the aerial connector and the aerial installation Check if you can see the analouge channels Check that the aerial is pointing in the right direction Check that the digital transmission are available in the aerea The TV Release function 0 will only work for SCART connected systems Change the Mediamaster output channel to a more suitable channel between 21 69 Or connect the system by SCART leads Try retuning your Mediamaster following the relevant steps in this manual If you are still missing channels your aerial may need adjusting Contact your dealer or Service Provider They will check this for you If the system is connected by SCART leads switch the TV to appropriate AV input If the system is connect
15. of the system software via satellite and from the Internet New software may include new or im proved features for existing menus Enter this menu to check for new software If new software is available you will get information in the menu on how to proceed If you download new software from Nokia Internet Pages you transfer the software from the computer to the Mediamaster via the serial port IMPORTANT Updating via satellite may take a while The front display will indicate the percent left to download NEVER turn off the Mediamaster never use the remote con trol or disconnect the antenna LNB cable during the download procedure This can damage the software and the receiver will have to be sent in for service Reinstall Use this option only if you have to start the complete installation procedure from scratch If you continue from here all your pre vious settings parental code and favourite channels etc will be erased If you do not want to change any settings you can leave this menu when the warning is displayed by pressing BACK User Preferences From here you can change the menu language You also have access to the Parental Control and the Appearance menus Language Preferences Menu Language Here you may select which language the menus will be shown In Main and Alternative audio language If more than one audio language is transmitted you may select the main and an alternative language Subtitl
16. posi tion within the list e Press gt again and the right side of the marked channel will change tov A e Move the channel to the desired position with W a and press OK It is also possible to first mark several channels and then move them all simultaneously e For each channel press the button to add it to the set of marked channels e Whenanumber of channels are marked this way and you want to move the whole set of channels press gt again e The marked channels will now be put together into one group e The right side of the first and last marked channel will change to a V arrows respectively e Use the corresponding buttons to move the selected channels to a new position within the list e When the channels are in the position you want press OK Delete Channels From here when the All TV list is selected in the Edit Chan nels menu you can delete channels Please note Channels deleted this way will be permanently deleted The only way to get them back is to perform a new channel search To delete channels Mark the channel you want to delete and press OK You will be asked if you really want to delete it If so confirm by pressing OK once more If not press BACK Remove Channels From here when the a favourite list is selected in the Edit Channels menu you can remove channels from those lists Mark the channel you want to remove and press OK You will be asked if you really
17. recep tlon may vary considerably Because the TV signal is amplified by reflections reception is often better than with analogue reception and ghost images can be avoided Reflection can even be used for reception by pointing the antenna at a mountain or a high building providing that they do not block the transmitter As with analogue TV weather can affect reception This is the case particularly at the edge of the reception area for digital trans missions GB 9 Connecting the Mediamaster There are many different types of TV VCR and other equipment that you can connect to the Mediamaster In this manual you will see some of the most common ways to connect your equipment If you use RF leads you will have to tune your TV and VCR to the Mediamaster output channel see page 12 If you have problems with your connections and need help con tact your dealer or Service Provider Connecting the Mediamaster to the TV e Connect a SCART lead between the main SCART socket on the TV and the TV SCART socket on the Mediamaster e Connect an RF lead from the TV VCR output on the Mediamaster to the RF input socket on the TV e Connect the TV aerial to the TV AERIAL input socket on the Mediamaster or use an indoor aerial Aerial Connecting a TV and VCR Refer to your VCR s manual for full instructions Antenn If your TV and VCR have two SCART sockets e Connect a SCART lead between the
18. select the freeze function Press once to freeze the screen picture Press any other key to go to normal mode again D Blue To toggle between present and previous TV Radio channels GB 5 Rear Panel Mains lead DIGITAL AUDIO AUX SCART TELEPHONE TV VCR 230 VAC phono connector for connection toa for modem for an RF 15 S PDIF output for VCR or an analogue connection to cable to the 50 60 Hz connection to satellite receiver the telephone aerial input a HiFi system wall socket of the TV or VCR E SSS TELEPHONE y 7 Camano mi A WARNING ce o po nor oren l e 1 E l AUDIOL R TV SCART SERIAL PORT TV AERIAL phono connectors for connec to read and load for a terrestrial con Stereo outputs for tion to the data information ventional TV aerial or connection toa HiFi TV an additional small system indorr antenna Front Panel EXIT MENU O Display to return from a to select to put the shows channel information menu to normal Main Mediamaster error messages remote control TV picture menu in and out of commands and time in stand by standby mode EXIT MENU A lt OK gt E Slot Slot Button VA OK lt gt fora Smartcard fora CA forthe CA for several functions for confirming for selecting settings module with module e g selecting channels choices and in a particular menu a Smartcard release
19. want to remove it If so confirm by pressing OK once more If not press BACK Channels removed from a list this way are not permanently de leted They are still available from the All TV list GB 22 REARRANGE CHANNELS All TY Krokek Move the selected channels by pressing the up or down arrow Ws exit GD Back to menu ss Deselect DELETE CHANNELS All TV Delete channel SVT1 by pressing OF exit Rack to reru eve Delete i REMOVE CHANNELS Remove channel SYT 1 from favourite list abt by pressing OK Exit Back to menu paa Remove Guide e Press GUIDE to get access to the receiver s EPG Refer to page 16 System Configuration You will be asked to enter your access code before you can open this menu The code is preset to 1234 from the factory The code can be changed from the Parental Control menu Re fer to page 26 S7STEM CONFIGURATION Channel Search ry TY Settings E Modem Configuration f Receiver Upgrade EW Reinstall If you want to customize the system to suit you better you can specify some settings from the submenus in the System Con figuration menu Please note that many of these functions are the same as in the First Time Installation Search manually or automatically for more channels Channel Search The Channel Search procedure can be performed in different ways You can
20. AAA batteries e a SCART lead fully featured 1 0 metre e an aerial RF lead double screened 1 5 metres e a telephone modem cable 10 metres with a splitter e an Owner s Manual e a Software License agreement About the SCART sockets e The rear panel of the Mediamaster is equipped with 2 SCART sockets see diagram When you connect other products to any of these sockets always use fully featured SCART leads as supplied There are less well specified SCART leads on the market and picture quality could be reduced if you use them Preparing the Remote Control e Remove the cover on the battery compartment at the bottom of the remote control e Insert the 2 AAA 1 5 V batteries as shown In the diagram taking care to observe the and markings indicated inside e Replace the cover Connecting to the TV aerial You can connect the Mediamaster to the following antennas 1 Standard outdoor antenna Where possible use an outdoor roof antenna UHF 21 69 Please note the following e n some residential buildings the communal roof mounted antenna includes a filter and channel selector If so the an tenna will probably not work with the Mediamaster Please consult the property owner e Many older roof mounted antennas can only receive a limited number of channels As a result digital channels transmitted on higher frequencies may be difficult to receive The problem can be solved by replacing the roof antenna
21. Code N l en Norrkoping Entersmart card code XxXxX User Preferences 2 SVT 2 Pi Access Code i SVT stnytt Enter access code XXXX C 2 ai C N J Viaccess Embedded y Edit Channels id Subscription information Parental Control MAs e O JAA i n 1 Receiver Lock Off E Ee EEEE 2 Age rating Control On 3 pongo cess N A 3 Age Limit 1 4 Delete lists ji 4 Change eccess Pa yy 5 Select Channels F ode changing 6 Lock Ch Is Viaccess Embedded p rocedure 7 e aei 2j 4 Subscription information p 8 Rearrange Channels 2 ChangeSmart Card Code Appearance Preferences 9 Delete Channels S J i Banner line out SS H 2 Volume Bar D 3 Volume Bar Time out 4 Subtitles 5 Picture format Code N System Configuration r 1 Channel Search N 2 TV Settings 4 3 Modem Configuration 4 Receiver Upgrade aber eet _ 5 Reinstall oor Edit Channels uide K J System Configuration User Preferences System Information S Viaccess Embedded Channel Search 1 1 1 Automatic Search N 2 Manual Search 2 J e e CidYdiCVS TV Settings fT o aaaeeeaa 1 TV Screen Format 2 2 TV Signal N J 3 RF Channel 4 RF Modulator type ee S 5 Position of the RGB Output 1 C J Manual Search ie N 1 Select Channel i g 2 Transmission Mode a ere ow a manon a a i i 3 SGuard Interval annel Search Progress ardware version f 1 een Configuration 4 Network Search TV Channels Software version SE2 0 EA Wise or TONG SVT 1 TV3 Boot software ve
22. card Smartcard Check that the Smartcard has been correctly inserted If the problem persists you may have a problem with the card Contact your dealer or Service Provider Viewing card faulty You have forgotten your secret PIN Contact your Service Provider They will code help you set it up again CA Module is not working CA module is not installed Check that the CA module has been CA module is not correctly inserted correctly inserted Contact your dealer or Service Provider Please note The first thing to do before sending the Media master to service is to 1 Perform Diagnostic procedure in System Information menu 2 Try downloading new software into the Mediamaster With this procedure the new software may solve the problem in the quickest and most efficient way See the relevant section Receiver Upgrade further on in this manual What to do if you can t solve the problem If you have tried all of the actions suggested above without solving the problem please contact your dealer or Service Provider FRONT PANEL DISPLAY 7 When power up boot version I product family and system soft ware version is shown When starting from standby prod uct variant and system software ver sion is shown Remaining time in percent during the download procedure In TV mode In video mode When downloading new software via the air The Mediamaster is in standby pou When downloading new software
23. cy of continuous development Therefore we reserve the right to make changes and improvements to any of the products described in this manual without any prior notice The EMC Directive 89 336 EEC is applied to this product DISEGC is a trademark of EUTELSAT Nokia is a registered trademark of Nokia Corporation Copyright 2000 Nokia Multimedia Terminals All rights reserved GB 3 GENERAL OPERATION OF THE MEDIAMASTER Throughout this manual you will notice that the everyday opera tion of your Mediamaster is based on a series of user friendly on screen displays and menus These menus will help you get the most from your Mediamaster guiding you through installation channel selection viewing and many other functions All functions can be carried out using the buttons on the remote control and some of the functions can also be carried out using the buttons on the front panel If at any time when using the menus except Installation and Reinstall you want to return to the normal TV mode press the EXIT button The Mediamaster is easy to use always at your command and adaptable for future advances Please be aware that new software may change the functional ity of the Mediamaster Should you experience any difficulties with the operation of your Mediamaster please consult the relevant section of this manual including the Problem Solving or alternatively call your dealer or a customer service adviser Please not h
24. d be aware that not all Service Providers have the necessary codes for these functions implemented in their EEE transmissions Enter new code watch TVG To cancellana Change access code From here you can change the access code from the standard 1234 DO NOT FORGET IT Without it you do not have access to any of the functions where the code is required Appearance Preferences Banner time out When you switch channels an information banner will be shown for a few seconds You can select for how long the banner will be shown APPEARANCE PREFERENCES Volume bar Select whether or not you want the volume bar to appear on the screen when you change the volume e emat M Cateri Select how bong the banner should be visible alter channel change seconds Watch Tv G Back one stop pa To select 3 Volume bar time out Select how long the banner will be visible on the screen Subtitles Select whether or not subtitles will be visible on the screen GB 26 Picture format If you have a TV set with the 4 3 picture format and the transmis sion is in 16 9 you can select Fullscreen or Letterbox Fullscreen will fill uo the screen but cut off some information on the left and right sides Letterbox will give a complete picture but leave black areas at the top and bottom letterbox format System Information If you have to contact your service p
25. e first thing to do before sending the Mediamaster to service Is to 1 Perform Diagnostic procedure in System Information menu 2 Iry downloading new software into the Mediamaster With this procedure the new software may solve the problem in the quickest and most efficient way See the relevant sec tion Receiver Upgrade further on in this manual FOR YOUR SAFETY e Allow clear space around the Media GB4 master for sufficient ventilation Do not cover the Mediamaster or place it on a unit that emits heat Use a soft cloth and a mild solution of washing up liquid to clean the casing Never allow liquids spray or other materi als to come Into contact with the inside of the Mediamaster Do not connect or modify cables when the Mediamaster is plugged in Do not remove the cover Do not allow the unit to be exposed to hot cold or humid conditions Service should be carried out only at a Nokia Authorised Service Centre Please note that the only way to isolate the Mediamaster completely from the mains supply is to unplug the mains lead REMOTE CONTROL This section describes how to operate the Mediamaster using the buttons on the remote control Some of the functions can also be carried out using the buttons on the front panel To switch the Mediamaster in and out of standby mode EXIT TV To return to the viewing mode from a menu without stor Jd ing settings in menu mode To turn the
26. ed by RF leads switch the TV to the channel for digital terrestrial TV If you have not manually tuned in the TV you may do this first Please look in the TV manaul for instructions PROBLEM SOLVING Problem Possible causes What to do You made a video recording of a The Mediamaster was not left on If you make a recording of digital digital terrestrial channel and whole the appropriate channel terrestrial TV your Mediamaster has to or parts of the programme was not be left on the channel you like to record recorded The system is connected by SCART If the system is connected by SCART leads and the VCR is not in AV EXT leads switch the VCR to appropriate AV mode input The system is connected by RF If the system is connected by RF leads leads and the VCR is not set to the switch the VCR to the channel for digital channel tuned for digital terrestrial terrestrial TV If you have not manually TV tuned in the VCR you may do this first Please look in the VCR manaul for instructions The remote control is not working Battery exhausted Change the batteries both Remote control is incorrectly Aim the remote control at box aimed Check that nothing blocks the front panel The Mediamaster is in standby Check if is flashing on the front panel mode display when you press a button If not replace the batteries both You see the on screen message The Mediamaster can t recognise Check that you are using the proper your smart
27. emote control to start the installation procedure If for some reason you have to change the RF channel later you can do this by using TV settings menu further on in this manual If you have a VCR connected it must be tuned to a different UHF channel between 21 to 69 than the Mediamaster You may now proceed to First Time Installation GB 12 kommen Welcome Tevetulga Velkommen Welkom Velko To cartina 9 j FIRST TIME INSTALLATION General Information Once you have correctly connected the Mediamaster you also have to perform a First Time Installation During this procedure helpful information is displayed at the bot tom of the menus Please note The OK button always confirms a selection within these menus and pressing it will take you to the next step in the installation process However and this is important often more than one value has to be entered in a menu First perform all necessary settings on the different lines Then confirm them all simultane ously by pressing OK You can always go back to the previous menu by pressing the BACK button Use the a v buttons to move upwards and downwards from one line to another Use lt gt to change settings You can also use the numeric buttons on the remote control to select a line in a menu and to enter numeric values The Welcome Menu This picture indicates that you have started the installation pro cedure e Change UHF channe
28. es If you select the Visible alternative for subtitling and more than one language is available you may select a main language and an alternative RECEIVER UPGRADE There is no new software version available Watch w Back one step asc To confirm i REINSTALL If you proceed with the reinstall all current channels and settings will be last Reinstall 0 Cancel ma USER PREFERENCES 1 E iA rance Preferences Set the prefered menu audio and subtitle langusges P ai Back one step ma To select 9 Alternative Audio Language English Subtitles Visible Main Subtitle Languag Svenska Alternative Subtitle Language English j Select the prefered menu language GB 25 Parental Control To open this menu you will be asked to enter your access code From the factory the access code is set to 1234 PARENTAL CONTROL The following settings can be altered from this menu Receiver lock ri lr af z If you select On you will have to enter the access code every meee Accesstoze d time you start the Mediamaster from stand by Age Rating Control Turn the receiver lock on or off If you want everybody to have access to all available types of pro Gav badont E Tess grammes select Off If you select On you may block programmes unsuitable for children Select an age limit between 4 and 18 years on the line that appears However you shoul
29. g the first installation a message no channels found is displayed or some channels are missing from the channel list Pressing 0 does not switch between a digital channel and an analogue channel There is interference on your digital terrestrial channels an existing terrestrial channel or video channels You can t find all the channels you think should be available There is no Welcome menu on the screen after you switched on the Mediamaster for the first time GB 30 Possible causes Mains cable is not connected The Mediamaster is in standby mode Signal to weak The Mediamaster is not set in TV mode The SCART connection has been made wrong or your TV has not selected the correct AV EXT channel The aerial is not properly connected to the Mediamaster The aerial is not pointing in the right direction The aerial is not suitable for digital channels The indoor aerial is not enough There are no digital transmission The system is not connected by SCART leads The system is RF connected but the TV is not tuned to its channel for digital terrestrial TV The system is connected by RF leads and the output channel of the Mediamaster interferes with an existing terrestrial channel or video channel The signal to your aerial may be weak Your aerial may need adjusting or your local transmitter may not be working The system is connected by SCART leads and the TV is not in AV EXT
30. h your an ee tenna has been configured Rearrange Channels Delete Channels The All TV list can contain a lot of channels By creating your own favourite lists you can make channel handling a bit more con Select this alternative to reale a new favourite list venient exit 3 Go back ja select 9 Important when editing channels Changes in the Edit Channels menus always take immediate ef fect it is not possible to cancel changes by pressing BACK GB 19 Create list From here you can create your own favourite lists containing the channels you watch most frequently You can give each list a spe cific name e g Sport or Films When a favourite list is selected you see only those channels defined in the list When you have given the list a name press OK and you will en ter the Select Channels menu see next page from where you add channels to the list How to give a specific name This procedure is the same whether you enter a name for the first time or change an existing e Move to anew character position by using P e To delete the last character use lt e Enter the characters one by one A Z 0 9 by using V A To speed up the procedure a bit you can use the double arrow buttons to jump 3 letters at the time e Figures can also be entered with the numeric buttons on the remote control e The next letter will be shown above the current and the pre vious below
31. ilable mes Current Information about sage will be shown time the next programme You may change channel lists with the lt gt buttons E ETA EE Kaai and name information GB 15 VIEWING MODE The i Information Button The Mediamaster has the ability to display information about pro grammes currently being broadcast as well as those being broad cast next ar By pressing the i button while watching TV you will get a spe cial Programme Information Banner Select channel with W or the numeric buttons The i symbol is coloured blue when displaying information about the current channel and red when information for another channel is shown ae e Press I gramme again to get more information about the current pro e f alot of information is available you can use the double ar row button to see the rest of the text ae e Press i a third time to return to TV mode e n this view you can select to get information about the cur rent and next programme by using the lt p gt buttons e You can leave the menus at any time and return to viewing TV by pressing EXIT Guide Press MENU Select GUIDE Press OK and you get access to the Nokia EPG which will give the titles of the current and next pro grammes on different channels Use the w a buttons to move the cursor to another programme Use the lt gt buttons to get information about next programmes Use the double
32. l number with w a CH 43 is indicated on the front display of the Mediamaster You only need to change the UHF channel if the channel is close and interfere with a transmitting analogue or digital channel in your area e Press OK on the remote control to start the Installation pro cedure kommen Welcome Tervetuloa elkommen Welkom Velko Language Select the desired menu language This will also be the main language for audio and subtitling LANGUAGE Svenska Select English as your preferred language by pressing Ok Go back ea Cantine fok GB 13 FIRST TIME INSTALLATION Channel Search The Channel Search procedure can be performed in two differ ent ways e Automatic Search or Manual Search Automatic Search e Start the Automatic Search on the digital terrestrial network by pressing OK Manual Search When you perform a Manual Search you first need to enter some parameters for the channel search to work The information you need to enter in this menu is available from your Service Provider Select channel Specify the UHF channelnumber between 21 to 69 If you enter the wrong figure s erase with the lt button Transmission Mode Select 8k Guard Interval Select the value as you want Network Search Select Yes if you want to search on all fre quencies in a specific network e Press OK to start searching for channels Channel Search Progress In the Channel
33. main SCART socket on the TV and the TV SCART socket on the Mediamaster e Connect a SCART lead between the VCR and the AUX SCART socket on the Mediamaster e Connecta SCART lead between the VCR and the second SCART socket on the TV e Connect an RF lead from the TV VCR output on the Mediamaster to the RF input socket on the VCR e Connect an RF lead from the RF output on the VCR to the TV AERIAL input socket on the TV e Connect the TV aerial directly to the TV AERIAL input socket on the Mediamaster Mediamaster Antenn If your TV has a SCART socket and the VCR has one SCART socket e Follow connection details from above but without the 3rd SCART lead Your VCR will then need to be tuned to the Mediamaster GB 10 You will be offered interactive services from your Service Pro vider You may then need to connect the Mediamaster to the tel ephone line e Connect the teleohone modem cable supplied from the Connecting an Analogue Satellite Receiver and VCR Connect a SCART lead between the main SCART socket on the TV and the TV SCART socket on the Mediamaster Connect a SCART lead between the TV SCART socket on the satellite receiver and the AUX SCART socket on the Mediamaster Connect a SCART lead between the VCR and the 2 nd SCART socket on the TV if available Connect an RF lead from the RF output on the VCR to the TV aerial input on the TV
34. mode and current time is shown via the Serial RS232 socket Error messages For service per sonnel Channel number in TV mode Lights when no signal is being re ceived Flashes when pressing a button on the remote control GB 31 RF channel in tuning mode TECHNICAL SPECIFICATIONS Transmission Standards DVB MPEG 2 RF input OFDM Modulator output Loop through output Input output connector IEC female IEC male RF input frequency RF input power level RF impedance Frequency range Frequency range Output channel Preset channel Output signal TV SCART Video output Audio output RGB output RGB bandwidth Fast blanking output Status output AUX SCART Video output Video input Audio output Audio input Status input Fast blanking input RGB input 470 to 862 MHz 77 dBm 75 Q Loop through 47 to 864MHz Re modulator 470 to 862 MHz UHF CH 21 69 43 PAL B G 1 Vee dB 75 Q 0 5 Vms R gt 10 KQ Internal RGB or from AUX SCART 5 8 MHz 3 dB Internal or from AUX SCART 0 6 12 V R 10 kQ 1V 1 dB 75 Q 1V p70 Q 0 5 Vims R gt 10 KQ 0 5 Vras R gt 10 kQ 0 6 12 V R gt 10 kQ 0 2 V for RGB bypass to TV SCART Yes DIGITAL AUDIO S PDIF Connector AUDIO R L Connector Output 1x RCA 2 x RCA R L 0 5 Vn 0 5 dB R 10 kQ SERIAL RS 232 Serial data Connector Signals Pin 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI ee ee ee ee
35. ocked channel or programme can only be unlocked with the special paren tal access code Parental Access code A four digit code stored in the Mediamaster Used to lock the Mediamaster PIN code Personal Identification Number A four digit code stored in the Smartcard For PPV Pay Per View or other services together with the subscription PPV Pay Per View Booking TV programmes in advance by calling up your Service Provider RF Radio frequency known as HF in some countries SERIAL RS 232 A serial communication standard data port SCART A 21 pin connector used for connection of the Mediamaster VCR and TV Also named Euroconnector or Peritel connector Scrambled satellite TV programme Some satellite TV programmes are transmitted in scram bled form A Smartcard and possibly a CA module will be needed to view such programmes Service provider Is a company that collects a number of programms serv ices and distributes them to customers S PDIF Sony Philips digital interface format Digital audio output SW Software Programme code VCR Video Cassette Recorder GB 29 PROBLEM SOLVING Problem The display on the front panel does not light up is not lit No sound or picture but the front panel shows the time or Bad picture blocking error The front panel shows a channel number but you can t see anything trom digital TV When the Mediamaster tries to find and store channels durin
36. perform an Automatic or a Manual Search CHANNEL SEARCH Marknatet TH Automatic Search Manual Search Automatic Search Refer to page 14 Perform automatic search to find channels Go back rc Enit ol Manual Search select 2 Refer to page 14 GB 23 TV Settings From here you can adjust settings concerning your TV TV screen format Select your TV screen format The 4 3 format is the standard format for most TV screens Select 16 9 for a wide screen TV TV signal If the teletext function does not work when watching channels from an analogue satellite receiver connected to the Media master change this setting from RGB to PAL RF channel Select this alternative if you have to change the RF channel If you change the RF channel number in the Mediamaster you must also change It to the same value on the TV If you do not the picture will become black Always test the receiver and any units connected to it before changing the RF channel Never use an RF channel number that is close to a transmitting channel one channel number or that is used by any of the connected units RF modulator type If the Mediamaster is connected to the TV by an RF lead you can select the RF modulator type The RF Modulator affects a chan nel s audio If you get picture but no sound the RF modulator se lection might be wrong Select UK PAL I if the Mediamaster is used in the UK Select Normal
37. rovider or a service center ETEA they might ask for information available from this menu There fore it is important that you first check the information in the following menus Channels 1 G Edit Channels E Guide o User Preferences 5E System Information 4 Conditienal Access System Configuration k ag er ho eg aaa System Information This gives general information about which hardware and soft ware version your Mediamaster is running on SYSTEM INFORMATION Hardwire versione 1514 Software wersiaon SE 2 10 3020 16 Boot software version pe exit GS Go back isa Diagnostics it 5 Diagnostics To find out the condition of certain parts of the Mediamaster you can run a diagnostic test f l DIAGNOSTICS The signal input strength is messured in signal to noice ratio Modem status and will normally give picture and sound if the value is Over 16 smart card detection 20 dB In bad weather atmospheric disturbances or other inter g Mitoprocessof check Signal input 28 2 dE S N ferences in the transmission the signal strength should be higher Exit QD Ga back me Repeat i GB 27 Conditional Access This menu will only be activated if you have inserted a valid Smartcard CA module in the slot behind the front lid If more than one CA system is activated select the one from which you want information The Viaccess Conditional Access CA Sy
38. rsion 260 2 Prefix digit SVT 2 TV 8 3 Digits after pause N g P TV 24 Kommande kanal 7 TV4 Kommande kanal J System Configuration y 4 lt M Eq Receiver Upgrade Diagnostics ES Looking for new software WMadenienans Pedi Se CA module communication No I Smart Card detection OK D Front End OK Microprocessor check OK System Configuration nee eae T lt ignal input 5 Reinstall Picture Ne a If you No J GB 33 TELEPHONE a J cono A gt Vaan a B CRUX ETE WARNING DO NOT OPEN ELECTRICAL Ab h h h h h h A SHOCK HAZARD Nokia is a registered trademark of Nokia Corporation 66 76938 11 www nokia se K o amp 0008
39. s you can close networks to reduce the number of channels You open close a network by marking it and pressing 4 A closed network is indicated with e Change channel lists with lt gt e You can change channel by stepping with the w a buttons or enter the channel number with the numeric buttons on the re mote control e Jo change one channel list page at a time use the double ar row buttons e Press OK when a channel name is highlighted to start watch ing to it e Youcan also get more information about a marked highlighted channel by pressing the i button Options Green Button By pressing the OPTION button you open a menu in which it is possible to enter temporary settings The menu will only appear if the programme contains any options to change Settings made in this options menu are only valid for the pro gramme you currently are watching If you leave the programme and return to it again the temporary settings will be gone Audio Language If available you can select among the different languages being broadcast Subtitle Language If available you can select among different subtitle languages It you select OFF you will not get any subtitling at all Indicates a closed network Name of the Channel list CHANNELS Y Marknatet Channel number and name Network name Indicates a scrambled channel CHANNELS Delivery System Marknatet Netwerk
40. sound off on mute o adjust the volume of digital programmes The Mediamaster s maximum level is controlled by the TV s present volume setting 0 9 To change channel and to select individual menu options Note If O is entered as the first digit the TV Release func tionality is activated see below 0 TV Release To switch between digital TV analogue TV and analogue satellite TV and VCR when your systems are con nected by SCART leads Info To display short and extended information if transmit ted about current and next programmes BACK To go back one level in the menus without storing settings TEXT To select teletext information Press to enter teletext if available MENU To display or exit from the Main Menu screen GUIDE To obtain a list of present and following programmes for the available channels This information is only shown if your Service Provider transmits programme information EPG in formation P P To change channels up and down J To change page in a menu list text if more than one page is e available To browse through teletext history A Vv To move up down in the menus and to change channels lt gt To change settings in menus OK To confirm choices and selection of a highlighted item To display the TV channel list R Red At the moment no function OPTION Green To select service options in viewing mode See Options FREEZE Yellow To
41. stem is embedded in the Mediamaster A Smartcard that supports this standard can be used in the left slot on the front panel Different CA modules with their Smartcards supporting the DVB Common Interface Cl standard can be used in the right slot VIACCESS EMBEDDED Viaccess embedded In this menu you select Subscription information or Change Smart Card Code SUBSCRIPTION INFORMATION Subscription SENDA a Card Nr 3245006079 Subscription information Start End Class Theme Dan 2000 00 15 2000 03 01 25 In this menu you get subscription information from a Smartcard 2000 0115 2000 03 01 255 3 2000 00 15 2000 03 01 O10 supplied by a Viaccess Service Provider 1999 12 15 2000 01 31 255 1989 12 15 2000 0131 255 Change Smart Card Code exit Goback ma Continue In this menu you can change the code on your Smartcard CHANGE SMART CAR Sgr pp noo mE Enter pew smart card code _ GB 28 GLOSSARY OF TERMS Access Authorisation to use the coding system to purchase order TV programmes Audio system With digital satellite reception the sound is transmitted in packages and Is selected either in a special audio mode or pre selected by using the installation set up This makes it possible to select between several different lan guages ina film The number of choices is dependent on what is available in the signal CA Conditional Access A system to control subscriber ac cess to services
42. ted to the TV with an RF lead and no SCART leads are used To tune your TV to the RF signal you might also need your TV manual in addition to this manual The steps below explain what to do if you have been unable to use SCART leads in your con nection Plug in your Mediamaster Tuning your TV to the Mediamaster Select a channel number on the TV that is not currently used for other TV channels Follow the instructions in your TV manual to tune the TV chan nel selector to UHF channel 43 this is the Mediamaster s fac tory preset UHF channel If you are already using this chan nel select another non occupied UHF channel between 21to 69 on the TV If you need to change UHF channel you do as follows First you change on the Mediamaster Use the w or A buttons on the front panel of the Mediamaster or on the remote You will see the UHF channel number displayed on the front panel of the Mediamaster Then you tune the TV channel selector to the same UHF channel When you have correctly changed the UHF channel number you will see the Welcome menu on the TV screen If there is interference from other channels you will have to change the chosen UHF channel Follow the instructions in your TV manual to store this UHF chan nel as the channel used by your Mediamaster You will have to select it when you want to watch terrestrial digital TV channels Once the welcome message is visible press the OK button on the Mediamasters r
43. wnload a large number of channels This may include channels also those to which you do not have access unless you have a Smartcard If you select a programme to which you do not have access you will get a message on the screen While viewing the current channel number will be shown on the front panel display In addition to the normal functions like switching the Media master in out of stand by changing the volume etc ref to the overview of the remote control there are some other useful func tions which will be explained in this part of the manual From this functions you can always go back to the previous menu by pressing the BACK button or return to TV mode by pressing EXIT Information about Programme Information eae een Pe list gramme Every time you change channels you will receive programme in formation for a few seconds In the User Preferences menu you can select how long this information will be shown The information may include Current time Channel list Channel number and name Name of the current and next programme The start and total time of the current programme A bar indicating the elapsed time of the current programme Recommended lowest age limit for watching the programme The start and total time of the next programme 10 00 222500 720 min SAT 2000 Programme information will only be available if it is included in the transmission Otherwise a No information ava
44. y pressing lt 4 gt e Press OK on a selected number to go to that page e Press EXIT BACK or TEXT to return to TV mode e The 0 button will show the index page normally page 100 A V will show the next or previous teletext page e You can use the double arrow buttons to browse through the pages you just have visited GB 18 ZUSCHAUER Fiat wenn Sie Fragen zum Programm des ARD ZDF vidani Mebin haben Fax O20 Di 40 42 Fragen zum Fernsehprogramm der ARD richten sie bitte an die ARD ZUS che rpm nthlt peo dott ai Fax oo 40 70 Fragen zum Fernsehprogramm de bitte an ee rue te Mainz 21 57 Die Adressen der Sender finden Si auf den VT Tafeln 615 und 625 General Information Many of the functions of the Mediamaster are available from the AIN MENU Main Menu S nT as Edit Cha Is e Press MENU to open it iem E System Configuration User Preferences G System Information Fj Conditional Access Channels Please refer to List of TV channels on page 17 Edit Channels From these menus you can create and edit channel lists You can among other things create favourite lists add delete rename and arrange the order of the channels within the lists EDIT CHANNELS In the All TV list the channels are presented network by net work First the name Marknatet terrestrial network Then the name of the network region TV transmitter for whic
Download Pdf Manuals
Related Search