Home

Autostart AS-1451HF Remote Starter User Manual

image

Contents

1. no key in the ignition switch while the engine is running For example if you stop for a delivery or at a conveni ence store lock your vehicle and leave it running for the length of a run cycle while you are away To leave the vehicle in idle mode 1 With the engine running press the Lock or UNLOCK button to unlock the doors or the START STOP button on the remote control until the parking lights come on 2 Remove the key and exit the vehicle The engine will go on running 3 Lock the doors if needed The engine will go on running until the user re enters the vehicle or until the expiration of the engine run time Caution Do not leave children or pets unattended in a vehicle standing in Idle Mode Turbo Mode If turbo mode is configured at installation it will allow a turbocharger to idle down after the user leaves the vehicle the unit will take over the vehicle and keep it running for 60 seconds or until it is shut down by remote control then shut down the engine Proceed as follows to set the system to Turbo Mode 1 With the engine already running press the Lock button on the transmitter until the parking lights come ON 2 Remove the ignition key from the ignition switch The engine will go on running 3 Exit the vehicle and close the door 4 Press the TRUNK button to lock the doors The engine will shut down after 60 seconds of Turbo Mode Valet Mode Valet Mode Using the Valet Switch if installed Wh
2. carried out once per remote start To stop the vehicle at any moment simply press the START STOP button Example lf your remote car starter is programmed for a run time of 4 minutes and your vehicle has been running for 3 minutes already pressing the START STOP button will reset the counter to zero and allow the engine to run for another cycle in this case 4 minutes Multi car Operation This option allows the owner of two vehicles both equipped with the same remote starter model to control both systems with a single remote control To control the second vehicle Note Your remote control must be configured for second car operation by the installer Press TRUNK LOCK buttons simultaneously ese LOCK Press TRUNK UNLOCK SIMUItANCOUSIY eects tesseeeeee UNLOCK Press TRUNK START STOP simultaneously cccscesssseseseenseene START Press TRUNK START STOP simultaneously STOP Press SHIFT gt SHIFT gt TRUNK ccccccccseesesesesesesesssssseseseeees TRUNK Or Press PANIC AUX gt PANIC AUX gt LOCK LOCK Press PANIC AUX gt PANIC AUX gt UNLOCK UNLOCK Press PANIC AUX gt PANIC AUX gt STARTISTOPS 1010111 START Press PANIC AUX gt PANIC AUX gt START STOP STOP Press PANIC AUX gt PANIC AUX gt TRUNK siise TRUNK Troubleshooting Poor Transmitting Range Many factors may affect the operating range of the transmitter Some of these are The co
3. AUTOMATIC TRANSMISSION REMOTE STARTER AS 1727 User Guide Table of Contents Table of Contents 0 cscs MiroduchioN euspena Using the Remote Control eee Multi Level Features default state Remote Starting Your Vehicle Vehicle Presets Drivinig Ofhisiasac seta actaatastss Using the Remote Starter eee Arming the Starter Kill tees Idle MOGE iva yisevtivetierlaveccien aaa vente TUDO MOd6 s cists a cssesteasiesteesison avin Valet Mode Valet Mode Using the Valet Switch if installOd enaena tie dntelonnaaeca Ignition Vale barranin ES Remote Valet Mode Panic Mode ne a aes Quick LOCKOUT eeseeseeseetesseeeeee Cold Weather Mode ceeccseeseeeeeeee Advanced Features Installation programmable Options cce 7 Remote Door LOCKS 7 Priority Door ACCESS eeseetesteteseetenees 7 Active or Passive Arming 7 The Starter Kill and the Anti grind Feature ia E E EE A E fein avin 7 Flashing LED vcccsccucnccedveeaanes 8 Sale Start vis ca ckha tenes seated saeavele 8 Ignition Controlled Door Locks 8 Ignition Re lock Secure LOCKS iriiria Turbo Mode seeen Remote Trunk Release ccccccee 8 Engine Run Time ceeseseseeeeeeeenee 8 Extended Run TIME 9 Multi car Operation Troubleshooting Poor Transmitting Range INDUSTRY CANADA USER NOTICE Operation is subject to the following two conditions 1 this device may not ca
4. CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE NO PERSON FIRM OR CORPORATION IS AUTHORIZED TO ASSUME FOR AUTOSTART ANY OTHER LIABILITY WITH RESPECT TO THE SALE OR USE OF OUR PRODUCTS AUTOSTART S LIABILITY WHETHER BASED ON CONTRACT TORT WARRANTY STRICT LIABILITY OR ANY OTHER THEORY SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT FOR DAMAGE IS THE BASIS OF THE CLAIM UNDER NO CIRCUMSTANCE WILL AUTOSTART ITS DISTRIBUTORS OR THEIR AGENTS BEAR ANY LIABILITY WHATSOEVER FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES The parties hereto elect that any dispute regarding the present document be submitted to the appropriate Court located in the Province of Quebec District of Montreal The parties hereto agree that this document is governed by and interpreted in accordance with the law of Quebec If the purchaser is located in a province of Canada other than Quebec all matters dealing with the warranty of quality will be governed by and interpreted in accordance with the law of Ontario If the purchaser is located outside Canada all matters dealing with the warranty of quality will be governed by and interpreted in accordance with the United Nations Convention on Contracts for the International Sale of Goods the Vienna Convention
5. aller to see if your vehicle is compatible with this option Multi Level Features default state Basic Features press the PANIC AUX button 1X PANIC AUX gt LOCK PANICIAUX gt START STOP Multi Car Operation press the PANIC AUX button 2X PANIC AUX gt PANIC AUX gt LOCK PANIC AUX gt PANIC AUX gt UNLOCK PANIC AUX gt PANIC AUX gt START STOP PANIC IAUX gt PANIC AUX gt TRUNK Customized Features press the PANIC AUX button 3X May not be applicable for certain vehicles Your installer can add customized features such as turning on the radio opening sliding doors etc PANIC AUX gt PANIC AUX gt PANIC AUX gt LOCK customized feature 1 PANIC AUX gt PANIC AUX gt PANIC AUX jai customized feature 2 PANIC AUX gt PANIC AUX gt PANIC AUX amp customized feature 3 PANIC IAUX gt PANIC AUX gt PANIC AUX customized feature 4 By default the multi level features are programmed as follows Level 1 Basic Features Level 2 Multi car operation Level 3 Customized Features To access a feature that is programmed as level 1 press the PANIC AUX button once followed by the desired function To access a feature that is programmed as level 2 press the PANIC AUX button twice followed by the desired function To access a feature that is programmed as level 3 press the PANIC AUX button three times followed by the desired function Your installer can customize the system as to personalize these multi level
6. door is closed The remote starter will not arm if a door is left open or if you re open a door within the 60 second delay Important note When the remote starter re arms automatically you can disarm the When the remote starter by simply pressing the UNLOCK button The Starter Kill and the Anti grind Feature With this added security feature the system will prevent your vehicle from starting with the ignition key when the starter kill is armed If your remote starter was installed with the starter kill option one will not be able to start your vehicle with the key unless the system has been unlocked and disarmed first or put into valet mode Note If the starter kill is installed your vehicle will benefit from a protection against starter motor damage that could occur after remote starting the engine should the user by force of habit turn the ignition key to the CRANK position User Guide P 7 Flashing LED The user may decide to turn on or off LED flashing at any moment To do so simultaneously press and hold the Lock and UNLOCK buttons on the transmitter Keep holding the buttons until the parking lights flash three 3 times At that point release the buttons The LED will toggle to its next state i e ON OFF There are three programmable options regarding the flashing LED i The LED flashes once the starter kill is activated passive or active arming and will turn itself off once the user turns the ke
7. ds b Ignition valet turning the key inside the ignition switch from OFF to ON 5 times in a row c By pressing the valet switch if included Panic Mode will automatically shut down after 30 sec Quick Lockout Also called secure panic For fast protection in emergency situations the system will Lock all doors when you press the brake pedal while you hear the sound signal Quick lockout is only available when panic mode has been set off Cold Weather Mode When cold weather mode is active the engine starts every 2 hours and runs for 4 minutes or for 9 or 20 minutes with diesel engines Cold weather mode automatically ends after 24 hours To enter Cold Weather Mode e Press the PANIC button and then the START STOP for 3 seconds e The parking lights will flash three 3 times To exit Cold Weather Mode do any one of the following actions e Open the hood e Start the engine by remote P 6 User Guide e Turn the ignition key to the IGNITION ON RUN position e Press the PANIC AUX button and then the START STOP button for three seconds the parking lights will flash once To verify whether the system is in cold weather mode Press and release the brake pedal If the vehicle is in cold weather mode the parking lights will stay on while the pedal is pressed Advanced Features Installation programmable Options The remote starter was designed with flexibility and OEM integration in mind With its program mable optio
8. e replaced if proven defective in material or workmanship and if when the accessory is returned to the point of purchase the retailer is provided with a copy of the proof of purchase The accessory will be sent to the retailer for the consumer to claim within a 4 four week period THE WARRANTY IS VOID IF 1 The product has been damaged altered in any way or tampered with without the explicit written consent of an Autostart technician For remote starter modules this includes the opening or removal of the plastic covering of the module or the removal or alteration of the barcode label on the plastic covering of the module The product is damaged due to accident fire flood shipping and handling misuse neglect or other conditions beyond the control of Autostart The product has been installed or repaired by anyone other than a certified technician The product has been improperly installed or used THE WARRANTY DOES NOT COVER Batteries Scratched or worn transmitter cases Installation and or removal charges for all remote starter modules and accessories Shipping and handling charges incurred for product exchange or replacement Any material damages other than to the product itself Harnessing L E D lights switches inverters relays etc THIS LIMITED LIFETIME WARRANTY SHALL CONSTITUTE THE SOLE LIABILITY OF AUTOSTART FOR OUR PRODUCTS AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED THERE ARE NO WARRANTIES OF MER
9. ehicle the remote starter must first disarm the factory security system The secure lock feature may be required on certain vehicle models with factory security systems that automatically unlock the doors when the security system is disarmed To keep your vehicle protected when the factory security system is disarmed for a remote start secure lock will relock your doors as soon as the vehicle has started Once the engine run cycle ends secure lock will rearm your factory security system Turbo Mode When left in turbo mode the remote starter will keep the engine running for 60 seconds before shutting it down This is to allow a turbocharger to idle down after the user leaves the vehicle See Turbo Mode section on page 5 Remote Trunk Release If your system was installed with the remote trunk release option you can open your trunk by pressing the TRUNK button Engine Run Time If you have a gas engine your remote starter can be programmed to run the engine for 4 15 or 25 minutes 15 minutes by default If you have a diesel engine the remote starter can be programmed to run the engine for 9 20 or 30 minutes 20 minutes default P 8 User Guide Extended Run Time While the vehicle is running under a remote start will reset the run time counter to zero and restart the run time cycle from the beginning The parking lights will flash three times and the horn if configured will honk once The extended run time procedure can only be
10. en your vehicle is in valet mode the remote starter functionalities are disabled If the vehicle needs to be serviced or if you park it indoors the valet mode will prevent the engine from being remote started accidentally To put the system into valet mode 1 Turn the ignition key to the IGNITION ON RUN position 2 Within 3 sec press the valet button 3 The parking lights will flash three times to indicate that the vehicle is now in valet mode Turn the ignition to the OFF position The L E D will come oN solid To take the system out of valet mode 1 Turn the ignition key to the IGNITION ON RUN position 2 Within 3 sec press and release the valet button 3 The parking lights will flash twice to indicate that the vehicle is now out of valet mode The L E D will go out Note Once valet mode is activated the remote starter and alarm functions will be disabled Ignition Valet This feature will allow you to remotely put your system into valet mode by using the ignition key instead of the valet button as above Ignition valet can be used without a valet button installed User Guide P 5 To put the system into valet mode Insert the ignition key into the ignition switch Within 10sec turn the key 5 times successively into the IGNITION ON RUN and OFF positions The parking lights will flash three times to indicate that the vehicle is now in valet mode The L E D will come On solid To take the
11. features in an order that best suits you Your options are 2 car lock 2 4 car unlock 2 4 car start stop 2nd car trunk Option 1 Level 1 requires pressing the PANIC AUX button 1X gt Multi car operation Level 2 requires pressing the PANIC AUX button 2X gt Basic features Level 3 requires pressing the PANIC AUX button 3X gt Customized features Option 2 Level 1 requires pressing the PANIC AUX button 1X gt Basic features Level 2 requires pressing the PANIC AUX button 2X gt Multi car operation Level 3 requires pressing the PANIC AUX button 3X gt Customized features Option 3 Level 1 requires pressing the PANIC AUX button 1X gt Customized features Level 2 requires pressing the PANIC AUX button 2X gt Multi car operation Level 3 requires pressing the PANIC AUX button 3X gt Basic features Option 4 Level 1 requires pressing the PANIC AUX button 1X gt Basic features Level 2 requires pressing the PANIC AUX button 2X gt Customized features Level 3 requires pressing the PANIC AUX button 3X gt Multi car operation User Guide P 3 Example If the multi level features were set to option 3 the setup would be as follows Levelt gt Customized feature Level2 gt Multi car operation Level3 gt Basic features The Basic features are now programmed as level 3 and therefore To access cold weather mode the user needs to press on the PANIC AUX but
12. ndition of the battery in the transmitter The operating environment for example downtown radio frequency noise airports cellular phone towers Metal any type of metal will affect operating range This includes the metal in the car The shape of the vehicle can affect range as well vans in general have an especially poor range The shape of the roof and A pillars brings about considerable radio frequency deflection in this case the signal from the remote control As a result the direction in which the vehicle is facing in relation to the remote control can affect the range Straight on standing in front of the vehicle generally gives you the greatest range the second best performance is from the back Using the remote control from either side of the vehicle will usually give the lowest range The range will be significantly lower in a crowded parking lot than in open space Always hold the transmitter high approximately at shoulder height Holding the transmitter against your chin will also increase your range your head acts as an antenna The operating range will be somewhat lower on vehicles equipped with an aftermarket or factory alarm User Guide P 9 LIMITED LIFETIME WARRANTY REMOTE STARTERS As the manufacturer 160031 Canada Inc Autostart warrants to the original consumer purchaser only nontransferable that the remote starter module control box shall be free from defects in materials and workmanship fo
13. ns this unit can single handedly control nearly any electrical system in your vehicle Caution The programming of your system should be left to a professional Changing any one of the settings may affect the operation of your remote starter The installation programmable options are as follows Remote Door Locks Ignition Re lock Priority Door Access Secure Lock Passive or Active Arming Turbo Mode Starter Kill Anti grind feature Remote Trunk Release Horn Chirp Timing Engine Run Time Safe Start Extended run time Ignition controlled Door Locks Multi car Operation Remote Door Locks If your remote starter was installed with the remote door locks option you will have the convenience of remote keyless entry See section Arming and Disarming the Remote Starter on page 4 for further instructions on remote door locking and unlocking Priority Door Access If the remote door locks option is installed on your vehicle this safety feature allows you unlock solely the driver s door with a single press of the UNLOCK button on the transmitter upon a second press of the UNLOCK button all the other doors will unlock Active or Passive Arming The starter kill can be configured either to passive mode so as to arm automatically or active mode so as to require user intervention for arming By default your remote starter is configured to passive mode In passive mode the starter kill will automatically arm 60 seconds after the last
14. ors Enter the vehicle and do the following Turn the ignition key to the IGNITION ON RUN position Do not turn the key to the CRANK position while the engine is running This would cause the starter motor to re engage Press the brake pedal to disengage the remote starter unit You are now ready to drive off Using the Remote Starter Arming the Starter Kill The starter kill if installed can be configured by the installer so as to arm automatically passive mode or not to arm automatically active mode See section passive or active arming on p 7 for more details on passive mode and active mode e To disarm the starter kill press the UNLOCK button on the transmitter The parking lights will flash twice If remote door locks are installed this will also unlock the doors e To arm the Starter Kill press the Lock button on the transmitter The parking lights will flash once If remote door locks are installed this will also lock the doors e In passive mode the starter kill will automatically arm if the ignition key is not inserted Into the ignition switch within 1 or 3 minutes after unlocking the key sense feature must be installed P 4 User Guide Idle Mode Convenience feature Idle mode allows you to keep the engine running and the doors locked while you stop for example at a convenience store or for a short delivery This feature allows you to let the remote starter take over control of the vehicle i e
15. r as long as the original consumer purchaser continuously owns the vehicle in which the remote starter was originally installed as specified below For the first year after the date of manufacture as specified by the serial number on the module Autostart will replace the remote starter module free of charge with a new remote starter module For the second year after the date of manufacture as specified by the serial number on the module Autostart will replace the remote starter module free of charge with a repaired or refurbished remote starter module For the third year and any consecutive year after the date of manufacture as specified by the serial number on the module Autostart will provide to the original consumer purchaser a repaired or refurbished remote starter module for a repair charge of 35 00 plus applicable taxes In all cases the consumer must return the remote starter module to the point of purchase and must provide a copy of the proof of purchase to said retailer A remote starter module will be returned to the retailer for the consumer to claim within a 4 four week period For case 3 a cheque in the amount of 35 00 plus applicable taxes must accompany the remote starter module or the retailer may refuse the return ACCESSORIES Autostart warrants to the original consumer purchaser only nontransferable that it will replace any Autostart accessory part for a one year period from date of purchase Accessories will only b
16. system out of valet mode Insert the ignition key into the ignition switch Within 10sec turn the key 5 times successively into the IGNITION ON RUN and OFF positions The parking lights will flash twice to indicate that the vehicle is now out of valet mode The L E D will go out Note With the ignition valet activated the remote starter and alarm functions will be disabled Remote Valet Mode This feature will allow you to remotely put your system into valet mode by using the transmitter instead of the valet button as above Getting into valet mode e Hold the UNLOCK and START STOP buttons simultaneously for 3 second e The parking lights will flash 3 times The LED will remain on solid Getting out of valet mode e Hold the UNLOCK and START STOP buttons simultaneously for 3 second e The parking lights will flash 2 times The LED will turn off Panic Mode Note Panic mode can only be activated if the horn has been adequately configured by your installer In an emergency situation you can activate panic mode by pressing and holding the PANIC button for 3 seconds If the vehicle is under a remote start you can shutdown the engine stop the horn by pressing the Lock button If the car is not running you can stop the horn by pressing the LOCK or UNLOCK Furthermore the panic mode can be stop by activating one of the following three 3 features a Remote valet pressing UNLOCK and START STOP for 3 secon
17. ton three 3 times followed by the START STOP button Remote Starting Your Vehicle Press the START STOP button for approx 1 second The parking lights will come on to inform you that the remote starter has received your signal Approximately 5 seconds later the engine will start The parking lights will remain on during the pre programmed run time of the engine If the vehicle does not start at the first attempt the system will shut down wait a few seconds and try to start the engine again There will be 3 start attempts before the system gives up Vehicle Presets Heater amp Heated Seat When leaving the vehicle it is recommended to preset the accessory controls in preparation for the next remote start Settings for the blower motor fan front and rear as well as heated seats if equipped should not be left on HIGH It is recommended to leave the settings on LOW or MEDIUM instead Windshield Wipers amp Radio amp Headlights Certain vehicles require the radio and or windshield wiper and or headlight circuits to become energized while running under remote start When leaving the vehicle you must ensure that the windshield wiper and headlight switches are off Leaving the headlight switch on on certain types of vehicles could cause them to remain on even after remote starter shut down resulting in a dead battery Driving Off With the vehicle running under remote control press the UNLOCK button to disarm and unlock the do
18. trol It can operate two independent vehicles equipped with an identical remote starter unit See Multi car operation section on page 9 The functions of the transmitter are as follows UNLOCK Button Unlocks all Doors and disarms the Starter Kill AUX5 Right Sliding Door RSD Button START STOP Button Starts or Stops the engine LOCK Button Locks all Doors and arms the Starter Kill AUX4 Left Sliding Door LSD Button TRUNK Button Activates the Trunk output AUX3 PANIC AUX Button Press 3sec will activate Panic Mode Horn must be connected This button also serves as a Shift button In combination with other buttons allows assigning different functions to those buttons e Pressing and holding the Lock button for more than 3 seconds will lock all doors and will send a constant pulse as long as the Lock button is held down maximum of 15 seconds This constant pulse can be configured to activate certain functionalities such as rolling up the windows Please refer to your installer to see if your vehicle is compatible with this option e Pressing and holding the UNLOCK button for more than 3 seconds will unlock all doors and will send a constant pulse as long as the UNLOCK button is held down maximum of 15 seconds This constant pulse can be configured to activate certain functionalities such as rolling down the P 2 User Guide windows Please refer to your inst
19. use interference and 2 this device must accept any interference including interference that may cause undesired operation of the device To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power EIRP is not more than that required for successful communication FCC USER NOTICE U S A This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment DOC 1 02 November 1 2006 TL Manufactured in Canada Introduction This is a state of the art remote starter system The system is packed with advanced features such as priority access to the driver s door commodity features and the safe start children safety feature With many an advanced function this product will satisfy any one your expectations from high end commodity and security systems without neglecting any standard feature commonly offered by entry level starters Using the Remote Control Your remote starter is equipped with a multi channel remote con
20. y to the IGNITION ON position ii The LED is totally disabled and will not flash it will turn on solid however when in valet mode iii The LED will flash once the starter kill is activated but requires pressing the UNLOCK button to turn itself off Failure to press the UNLOCK button will make the LED flash even if the key is in the IGNITION ON position Safe Start If this feature is enabled the user must press the START STOP button 2 times within 3 seconds to remote start the vehicle This will eliminate accidental remote starts e g when children are playing with the transmitter If swap start mode is selected to remote start your vehicle press the PANIC AUX button and then the Lock button The aux 2 output can be activated by pressing the START STOP button Ignition Controlled Door Locks This is an added security feature If your remote starter was installed with the ignition controlled door locks option the doors will automatically be locked as soon as the ignition key is turned to the IGNITION ON RUN position while the brakes are pressed When the key is turned to the OFF position the doors will automatically be unlocked Ignition Re lock On remote starters of this series when ignition controlled door locks are enabled and the ignition key is in the IGNITION ON RUN position should any door be unlocked and opened all doors will be relocked next time the brake pedal is pressed Secure Lock Before it can remote start your v

Download Pdf Manuals

image

Related Search

Related Contents

Antoine de SAINT  Samsung R1245AS 用户手册  Mastiff 91 Safety and Operation / Maintenance and Parts  Dialogue - automne 2008 : le magazine de la Banque  Samsung EB40D User Manual    Fiber QuickMap™  Vancouver CD35  DYNAPAC CA150 ENTRETIEN  FTL-210-FTL-252 ab 2011  

Copyright © All rights reserved.
Failed to retrieve file