ATD Tools ATD- 7371 Automobile Parts User Manual
Contents
1. No alterations shall be made to this product Failure to heed these markings may result in personal injury and or property damage Be sure all tools and personnel are clear before lowering load Only attachments and or adapters supplied by the manufacturer shall be used Lift only on areas of the vehicle as specified by the vehicle manufacturer PREPARATION Before Use 1 Verify that the product and application are compatible if in doubt call ATD Technical Service 636 327 9050 2 Before using this product read the operator s manual completely and familiarize yourself thoroughly with the product its components and recognize the hazards associated with its use 3 Assemble handle ensure spring clips align with slots 4 To familiarize yourself with basic operation use the notched end of provided handle to engage and turn the release valve a Clockwise until firm resistance is felt to further turning This is the CLOSED release valve position used to raise the ram plunger b Counter clockwise but no more than 1 turn from the closed position This is the OPEN release valve position used to lower the ram plunger 5 With ram fully retracted locate and remove the oil filler plug screw Insert the handle into the handle sleeve then pump 6 to 8 strokes Ensure the oil level is just below the oil filler hole Reinstall the oil filler plug screw 6 Pour a teaspoon of good quality air tool lubricant into the air sup2. Wentzville MO 63385 636 327 9050
3. 0 RUS x 6 1 2 RUS RUS ES 1 2 ECTS 1 2 5 st ES 1 2 ATD 7372 8 1 2 x 7 1 4 8 1 8 15 1 2 3 3 8 Saddle Extension Screw ER Air Motor Quick Coonnector N A for ATD 7372 lt Air Hose Oil Filler Screw Plug AY ye ou oil filler plug for ATD 737 Carry Handle gt Lift Control Valve Handle Sleeve Release Valve lt Handle Figure 1 Typical Air Bottle Jack Nomenclature 2 Study understand and follow all printed materials provided with on this product before use Do not exceed rated capacity This is a lifting device only Immediately after lifting support the load with a pair of appropriately rated jack stands e Use only on hard level surface To avoid crushing and related injuries e Never work on under or around a load supported only by hydraulic jack e Always use adequately rated jack stands e Chock each unlifted tire in both directions Do not use this device to lift level lower support nor move a house mobile home travel trailer camper or any building structure e Be alert and sober when using this product Do not operate under the influence of drugs or alcohol e Do not use adapters or accessories that are not provided initially e Lift only on areas of the vehicle as specified by the vehicle manufacturer Never wire clamp or otherwise disable the lift control valve to function by other than operator s hand
4. Air Hydraulic Bottle Jacks POVAN Operating Instructions amp Parts Manual Model Number Capacity ATD 7370 12 Ton ATD 7371 20 Ton ATD 7372 a 20 Ton low profile U S Patent No s 5 341 723 5 946 912 A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death e Leer comprender y seguir las instrucci nes antes To avoid crushing and related injuries de utilizar el aparato El manual de instrucci nes y la informaci n de load supported only by a hydraulic seguridad deben estar comunicado en lengua del A jack ALWAYS use adeguately rated NEVER work on under or around a operador antes del uso jack stands e No seguir estas indicaci nes puede causar da os personales o materiales ATD Tools Inc 160 Enterprise Drive Wentzville MO 63385 Printed in China ATD7370 M2 rev 02 09 SAFETY and GENERAL INFORMATION Save these instructions For your safety read understand and follow the information provided with and on this jack before using The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use The owner and operator shall be aware that use and repair of this product may require special skills and knowledge Instructions and safety information shall be conveyed in the operator s native language before use of this ja
5. ck is authorized If any doubt exists as to the safe and proper use of this jack remove from service immediately Inspect before each use Do not use if broken bent cracked or damaged parts including labels are noted Any jack that appears damaged in any way operates abnormally or is missing parts shall be removed from service immediately If the jack has been or suspected to have been subjected to a shock load a load dropped suddenly unexpectedly upon it immediately discontinue use until jack has been checked by an authorized factory service center contact distributor or manufacturer for list of Authorized Service Centers It is recommended that an annual inspection be done by qualified personnel Labels and Operator s Manuals are available from manufacturer PRODUCT DESCRIPTION Air Actuated Hydraulic Bottle Jacks are designed to lift not support rated capacity loads consisting of one end of a vehicle Immediately after lifting the load must be supported by a pair of appropriately rated jack stands Ensure that air source can dedicate 7 8 CFM 110 175 psi A minimum of 150 psi air pressure is required to raise rated capacity load Never use hydraulic jack as a stand alone device After lifting immediately support the lifted load with a pair of appropriately rated jack stands Never place any portion of your body under a load when lifting or lowering the load SPECIFICATIONS a a Saddle ATD 7370 ATD 7370 1270 127
6. g the Ram Plunger 1 Assemble handle ensure that spring clips align with slots 2 Place vehicle in the park with emergency brake on and wheel securely chocked to prevent inadvertent vehicle movement 3 Locate and close release valve by turning handle clockwise until firm resistance is felt to further thread engagement 4 Verify lift point center jack saddle under lift point 5 Squeeze the lift control valve or insert handle into handle sleeve and pump to contact lift point To lift continue pumping until load reaches desired height DO NOT OPERATE BY AIR AND BY HAND PUMPING AT THE SAME TIME 6 Immediately transfer the lifted load to a pair of appropriately rated jack stands A Do not use an extender on the air hose or the operating handle Lowering Make certain that all personnel are clear of the load before lowering Control the rate of descent ofthe load at all times The more you open the release valve the faster the load descends 1 Raise load high enough to clear the jack stands then carefully remove jack stands always used in pairs 2 Slowly turn the handle counter clockwise but no more than 1 turn If the load fails to lower a Use another jack to raise the vehicle high enough to reinstall jack stands b Remove the affected jack and then the stands c Lower the load by turning the release valve counter clockwise but no more than 1 turn 3 After removing jack from under the load push ram and handle sleeve down to red
7. on may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state REPLACEMENT PARTS refer to page 6 amp 7 Not all components of the jack are replacement items but are illustrated as a convenient reference of parts location When ordering parts give part number and parts description Call or write for current pricing ATD Tools Inc 160 Enterprise Drive Wentzville MO 63385 Tel 636 327 9050 Fax 636 327 9044 Replacement Parts Illustration for model ATD 7370 ATD 7371 amp ATD 7372 Ma TZ I N Figure 2 Replacement Parts Illustration for Model ATD 7370 ATD 7371 8 ATD 7372 6 Replacement Parts List for model ATD 7370 ATD 7371 8 ATD 7372 3p VA aj aa R27060 0008 TIT 1 Co aa nA arets 1 oooO Pump Piston 1 as EEE CE EX EE 17 5406 07024 000 Pin CN Lie IN CEC TEO ECN ase Amor Seaikitimdudestia ssem CEE ro eli Arme Atorsr010 STEEL ET AK DU 1177777 ena ECT Seal Kit Contents a jorma 2 a Dustwper 1 Co forng fi foisa 5 a RamBeaing e Bakur 1 C Toma torarrariaarozara 4 Items included and available only as Seal Kit Replacement reguires special skills knowledge and eguipment Only an authorized service center may perform the repair and or replacement of these items Contact ATD technical service for list of service centers 7 ATD Tools Inc 160 Enterprise Drive
8. ply inlet of the lift control valve Connect to air supply and squeeze lift control valve for 3 seconds to evenly distribute lubricant 7 This product is equipped with the popular 1 4 NPT air coupler When installing a different air coupler of your choice ensure that thread tape or compound is used when servicing connections To ensure dependable trouble free operation an inline air dryer and oiler is recommended 8 Check that the pump operates smoothly and that the extension screw will thread up down easily before putting into service Replace worn or damaged parts and assemblies with ATD authorized replacement parts only Bleeding Venting Trapped Air With the release valve in the OPEN position 4b above and with ram plunger fully lowered locate and remove the oil filler plug screw Insert the handle into the handle sleeve then pump 6 to 8 full strokes This will help release any pressurized air which may be trapped within the reservoir Oil level should be even with the bottom of the oil filler hole Reinstall the oil filler plug screw Use only handle provided by jack manufacturer The handle provided with this jack will safely engage the release valve and operate the handle sleeve If handle is worn operates abnormally or will not positively engage the release valve STOP discontinue use of the jack until a factory replacement handle can be acquired A Paint contains lead DO NOT sand or grind painted surface 3 OPERATION Raisin
9. r replace at its option without charge any of its products which fails due to a defect in material or workmanship under normal usage This limited warranty is a consumer s exclusive remedy Performance of any obligation under this warranty may be obtained by returning the warranted product freight prepaid to ATD Tools Inc Warranty Service Department 160 Enterprise Drive Wentzville MO 63385 Except where such limitations and exclusions are specifically prohibited by applicable law 1 THE CONSUMER S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE 2 ATD Tools Inc SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER 3 ANY IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO ONE YEAR OTHERWISE THE REPAIR REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED 4 ANY MODIFICATION ALTERATION ABUSE UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND IS NOT COVERED BY THIS WARRANTY Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusi
10. re to fully distribute the oil inside the air motor Cleaning Periodically check the pump piston and ram for signs of rust corrosion Clean as needed and wipe with oily cloth Note Never use sandpaper or abrasive material on these surfaces Storage When not in use store the jack with pump piston and ram plunger fully retracted and air supply disconnected 4 TROUBLESHOOTING Symptom Possible Causes Corrective Action Jack will not lift load e Release valve not tightly closed e Overload condition Air pressure inadequate e Ensure release valve tightly closed e Remedy overload condition e Ensure adequate air pressure Jack will lift but not maintain pressure e Release valve not tightly closed e Overload condition e Hydraulic unit malfunction e Ensure release valve tightly closed e Remedy overload condition e Contact ATD Tech Service Jack will not lower after unloading Reservoir overfilled e Ensure load is removed then drain fluid to proper level Poor lift performance e Fluid level low Air trapped in system e Ensure proper fluid level e With ram fully retracted remove oil filler plug screw to let pressurized air escape then reinstall oil filler plug screw Will not lift to full extension e Fluid level low e Ensure proper fluid level ONE YEAR LIMITED WARRANTY For a period of one 1 year from date of purchase ATD Tools Inc will repair o
11. uce exposure to rust and contamination MAINTENANCE Important Use only good grade hydraulic jack oil Avoid mixing different types of fluid and NEVER use brake fluid turbine oil transmission fluid motor oil or glycerin Improper fluid can cause premature failure of the jack and the potential for sudden and immediate loss of load We recommend Mobil DTE 13M or equivalent Adding oil 1 With ram plunger fully lowered and pump piston fully depressed set jack in its upright level position Remove oil filler plug screw 2 Fill with oil until just below the rim of the oil filler screw hole Reinstall the oil filler plug screw Changing oil For best performance and longest life replace the complete fluid supply at least once per year 1 With ram plunger fully lowered and pump piston fully depressed remove the oil filler plug screw 2 Lay the jack on its side and drain the fluid into a suitable container Note Dispose of hydraulic oil in accordance with local regulations 3 Fill with oil until just below the rim of the oil filler hole Reinstall the oil filler plug screw Lubrication 1 A periodic coating of light lubricating oil to pivot points will help to prevent rust and assure that pump assemblies move freely 2 Air pump should be internally lubricated before each use Use good quality air tool lubricant If no inline oiler is used pour a teaspoon of air tool oil into the air control valve inlet Operate the jack with air pressu
Download Pdf Manuals
Related Search