AOC CT700G Computer Monitor User Manual
Contents
1. CEE 22 female configuration TECHNICAL SUPPORT FAQ Power LED is not on Inspec Make LOCK LOCK hitting BLUE Power Cord should be connected No Plug amp Play Check if the PC System is Plug amp Play compatible Check if the Video Card is Plug amp Play compatible Check if the D 15 plug pin of Video Cable is bent Make sure the AOC Monitor Drivers are installed AOC Monitor Drivers are available at www aocmonitor com Picture is fuzzy Adjust the Contrast and Brightness Controls Picture bounces or a wave pattern is present in the picture Move electrical devices that may cause electrical interference The power LED is ON orange but there s no video or no picture Computer Power Switch should be in the ON position Computer Video Card should be snugly seated in its slot Make sure monitor s video cable is properly connected to the computer monitor s video cable and make sure none of the pins are bent sure computer is operational by hitting the CAPS key on the keyboard while observing the CAPS LED The LED should either tum ON or OFF after he CAPS LOCK key Missing one of the primary colors RED GREEN or Inspec the monitor s video cable and make sure that none of the pins are bent INSTALLATION INSTRUCTIONS SWIVEL BASE To attach the swivel base to the monitor do the following e Carefully turn the monitor on its side or upside down see figure 1 e L2. audio cable between the computer multi media or sound card s audio output and monitor s audio input Connecting the DC Power Cable CT740g only Plug DC power cable between monitor to swivel base for audio power w OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS The other control knobs are located at the base of the monitor See Figure 3 By changing these settings the picture can be adjusted to your personal preferences e The power cord should be connected e Connect the video cable from the monitor to the video card e To tum the monitor on press the power switch to ON position The power indicator will light up e Your monitor features a unique quick switch system which provides a picture within seconds after the monitor is switched on NOTES e Do not install the monitor in a location near heat sources such as radiators or air ducts or in a place subject to direct sunlight or excessive dust or mechanical vibration or shock e Save the original shipping carton and packing materials as they will come in handy if you ever have to ship your monitor e For maximum protection repackage your monitor as it was originally packed at the factory e To keep the monitor looking new periodically clean it with a soft cloth Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution Never use strong solvents such as thinner benzene or abrasive cleaners since these will damage the cabinet As
3. by one or more ofthe following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help NOTICE The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Shielded interface cables and AC power cord if any must be used in order to comply with the emission limits The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment It is the responsibilities of the user to correct such interference As an ENERGY STAR Partner Envision Peripherals Inc has determined that this product meets the ENERGY STARS guidelines for energy efficiency WARNING To prevent fire or shock hazard do not expose the monitor to rain or moisture Dangerously high voltages are present inside the monitor Do not open the cabinet Refer servicing to qualified personnel only N Ed PRECAUTIONS e Do not use the monitor near water e g near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement e Do not place the monitor on an unstable cart stand or table If the monitor falls it can injure a person and cause serious damage t
4. CT700G CT710G CT720G CT740G User s Manual Thank you very much for choosing the AOC Color Monitor We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor Please keep this manual in a safe place for you future reference Plug amp Play Drivers for the AOC Series Monitors are available at www aocmonitor com CHECKING THE CONTENTS OF THE MONITOR PACKAGE The product package should include the following items 1 Monitor 2 Owner s Manual 3 Power Cord 4 Swivel Base 5 Audio Cable DC Power Cable For CT740g only FCC Class B Radio Frequency Interference Statement WARNING FOR FCC CERTIFIED MODELS NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference
5. RO Offmode lt 5W Power consumption 75 Watts Max Preset display area 310mm x 230mm ae 1W per channel Regulations UL CSA FCC FDA Factory Preset Timing Table HORIZONTAL VERTICAL Er RESOLUTION FREQUENCY FREQUENCY 720x400 720x400 400 MEE 5kHz He VESES 40460 REIT VESA 85 800 x 600 VESA 85 1024 x 768 53 7kHz 85Hz 68 7kHz 85Hz VESA 60 1280 x 1024 64 0kHz CONNECTOR PIN ASSIGNMENT 15 Pin Color Display Signal Cable PIN NO DESCRIPTION PIN NO DESCRIPTION 1 Red 9 NC 2 Green 10 Ground 3 Blue 11 Monitor Ground 4 Ground 12 DDC Serial Data 5 Ground 13 H Sync 6 R Ground 14 V Sync V Clk 7 G Ground 15 DDC Serial Clock 8 B Ground Ey For DDC
6. TE PROPERLY THERE MUST BE A VIDEO INPUT SIGNAL This monitor meets the Green Monitor standards as set by the Video Electronics Standards Association VESA and or the United States Environmental Protection Agency EPA and The Swedish Confederation Employees NUTEK This feature is designed to conserve electrical energy by reducing power consumption when there is no video input signal present When there is no video input signal this monitor following a time out period will automatically switch to an OFF mode This reduces the monitor s internal power supply consumption After the video input signal is restored full power is restored and the display is automatically redrawn The appearance is similar to a Screen Saver feature except the display is completely off The display is restored by pressing a key on the keyboard or clicking the mouse USING THE RIGHT POWER CORD The accessory power cord for the Northern American region is the wallet plug with NEMA 5 15 style and is UL listed and CSA labeled The voltage rating for the power cord shall be 125 volts AC Supplied with units intended for connection to power outlet of personal computer Please use a cord set consisting of a minimum No 18 AWG type SJT or SVT three conductors flexible cord One end terminates with a grounding type attachment plug rated 10A 250V CEE 22 male configuration The other end terminates with a molded on type connector body rated 10A 250V having standard
7. a safety precaution always unplug the monitor before cleaning it Installing and Removing the Swivel Base Figure 3 External Control Knob ee HOW TO ADJUST A SETTING CONNECTING CABLES 1 Press the Shuttle Knob Key to make the OSD window 1 Power Cord 4 PC Audio Output appear See figure 4 1 2 Signal Cable 5 DC Output 2 Rotate the Shuttle Knob to select the desired function 3 VGA Card Adapter See figure 4 E 3 Press the Shuttle Knob again to select the function that you want to adjust 4 Rotate the Shuttle Knob to change the settings of the current EXTERNAL CONTROLS function E Shuttle Knob 5 When the OSD window is active it shows the input signal 9 Power Indicator timing The H stands for the horizontal frequency and V for the vertical frequency 3 Power button 6 To exit and save select the exit function or leave the monitor alone for 10 seconds If you want to adjust any other function repeat steps 2 4 H 68 8KHz V 85Hz 0 200000 FRONT PANEL CONTROL e Power button When pressed the monitor enters the off mode and Contrast the LED flashes Press again and hold to restore normal status e Shuttle Knob 70 The Shuttle Knob is used to control the monitor a functions Rotate to switch functions or adjust settings A A 9300 Gp 8500 O
8. g Press to select or execute a function e Power Indicator 1024 X 768 Green Power On mode Blinking Green Off mode Figure 4 The OSD Message ADJUSTING THE PICTURE 1 O CONTRAST Adjust the picture contrast 2 s BRIGHTNESS Adjust the picture brightness Adjust the horizontal position Adjust the picture s horizontal size 4 HRGENTER of the picture H SIZE 5 V CENTER Adjust the vertical position of the picture 6 O V SIZE Adjust the picture s vertical size Te ZOOM Adjust the picture s horizontal and vertical size simultaneously 8 LU PINCUSHION Adjust the pincushion and barrel 9 IA TRAPEZOID Adjust the picture s trapezoid distortion 10 Cl PIN BALANCE Adjust to compensate the pincushion unbalance 11 CJ PARALLELOGRAM Adjust the picture to be a rectangle 12 ROTATION Adjust the picture tilt to horizontal position 6500 K 9300 K The color temperature for 6500 K is x 0 313 y 0 329 and 9300 K is x 0 283 y 0 297 It 13 COLOR presents two different color sets on the screen You can select 9300 K or 6500 K by pressing TEMPERATURE the Shuttle Knob USER COLOR If the 9300 K normal white or 6500 K warmer white do not satisfy your desire properly adjust 14 ae Red Blue R B GAIN controls to obtain your optimum whiteness level DEGAUSS If color impurity occurs when moving or swiveling the monitor press the Shut
9. ing can result in fire or electric shock Never push any object into the slot on the monitor cabinet It could short circuit parts causing a fire or electric shock Never spill liquids on the monitor e Do not attempt to service the monitor yourself opening or removing covers can expose you to dangerous voltages and other hazards Please refer all servicing to qualified service personnel e To ensure satisfactory operation use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 240V AC Min 2 5A The wall socket shall be installed near the equipment and shall be easily accessible e Attention Disconnect the power cord to stop the power supply to the monitor Plug amp Play DDC1 2B Feature This monitor is equipped with VESA DDC1 2B capabilities according to the VESA DDC STANDARD It allows the monitor to inform the host system of its identity and depending on the level of DDC used communicate additional information about its display capabilities The communication channel is defined in two levels DDC1 and DDC2B The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information The DDC2B is a bidirectional data channel based on the I C protocol The host can request EDID information over the DDC2B channel THIS MONITOR WILL APPEAR TO BE NON FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL IN ORDER FOR THIS MONITOR TO OPERA
10. o the appliance Use only a cart or stand recommended by the manufacturer or sold with the monitor If you mount the monitor on a wall or shelf use a mounting kit approved by the manufacturer and follow the kit instructions e Slots and openings in the back and bottom of the cabinet are provided for ventilation To ensure reliable operation of the monitor and to protect it from overheating be sure these openings are not blocked or covered Do not place the monitor on a bed sofa rug or similar surface Do not place the monitor near or over a radiator or heat register Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided e The monitor should be operated only from the type of power source indicated on the label If you are not sure of the type of power supplied to your home consult your dealer or local power company e The monitor is equipped with a three pronged grounded plug a plug with a third grounding pin This plug will fit only into a grounded power outlet as a safety feature If your outlet does not accommodate the three wire plug have an electrician install the correct outlet or use an adapter to ground the appliance safely Do not defeat the safety purpose of the grounded plug e Unplug the unit during a lightning storm or when it will not be used for long periods of time This will protect the monitor from damage due to power surges e Do not overload power strips and extension cords Overload
11. ocate the cavities at the bottom front of the monitor e Insert the pegs on the swivel base into these cavities Push the swivel base forward until the swivel base locks in place e To remove the swivel base hold the bottom of the swivel base then push it out POWER CORD Power Source 1 Make sure the power cord is the correct type that required in your area 2 This monitor has a universal power supply that allows operation in either 100 120V AC or 220 240V AC voltage area No user adjustment is required Connect the power cord into your monitor s power input socket and then plug the other end into a 3 pin AC power outlet The power cord may be connected to either a wall power outlet or the power outlet socket on your PC depending on the type of power cord supplied with your monitor VIDEO CABLE Connecting the Video Cable the monitor comes with a built in video cable Plug the signal cable s 15 pin connector into the computer s video port and tighten the two screws on the cable connector see figure 2 Caution Don t bend the signal cable otherwise it will break the inner wire Connecting the Power Cord Plug the power cord into the monitor s AC power jack Then plug the power cord into a grounded AC outlet UL approved power strip or the power output socket on your PC Caution If the AC outlet is not grounded install the proper grounding adapter not supplied Connecting the Audio Cable CT740g only Plug
12. tle Knob and 15 Q degauss to fix the picture condition MOIRE REDUCE Moire is the result of interference between the phosphor layout and the video signal In some 16 A cases you may find the moire very noticeable Press the Shuttle Knob to enter in the moire reduce setting Please adjust the level to the optimum condition Note Too high of a setting will cause the picture to shake 17 D RECALL Press RECALL to restore the monitor to factory settings 18 Exp exit Close OSD window 19 3 SELECT LANGUAGE Select the language as you like SPECIFICATION CRT 43 2cm 17 90 deflection 0 23mm H 0 27mm D dot pitch 29mm neck Viewable Image Size 40 6cm 16 diagonal Video 0 7Vpp R G B Analog Separate Sync TTL Level H V sync Positive Negative Scanning Frequency Horizontal 30kHz to 72kHz automatically Vertical 50Hz to 160Hz automatically Max Resolution 1280 x 1024 Video Dot Rate 110MHz Factory Preset mode 6 User Programmable mode 8 Power Source Universal AC 100 240V 50Hz 60Hz Operating 0 C to 40 C ambient Humidity 10 to 85 relative non condensing Dimension Monitor amp Base ICT700 410 W x 402 H x 420 D mm ICT740 410 W x 440 H x 420 D mm Weight ICT700 15 5 kg Net ICT740 16 3 kg Net Signal Cable Attached Mini D sub 15 Male Plug amp Play DDC1 2B EPA ENERGY On mode lt 75W STA
Download Pdf Manuals
Related Search