ADTX ZRW113 Switch User Manual
Contents
1. RESET UNIT removes it completely from the network BASIC OPERATION Local Control The switch paddle on the ZRW113 allows the user to e Include or exclude the module from the Z Wave system e Turn on or off the attached load e Control other Z Wave enabled devices associated with the ZRW113 Also when a controller prompts you to Send Node ID or to Press Button on Unit quickly tap the switch on or off once to satisfy those instructions e Tapping top of switch turns the load attached ON e Tapping bottom of switch turns the load attached OFF e Pressing and holding switch does not effect the load attached but will allow dimming and brightening of Z Wave dimmers if associated to the ZRW1 13 see below for details LED indication The LED on the ZRW113 will turn on when the load attached is ON However the LED can be user configured to turn ON when the load attached is OFF to act as a night light if so desired See ADVANCED OPERATION The ZRW113 will flicker its LED when it is transmitting to any of its 2 groups This can be changed if desired see ADVANCED OPERATION Auxiliary Switch The ZRW113 supports the AS101 auxiliary switch to provide 3 way or 4 way operation Remote Control The ZRW113 will respond to BASIC and BINARY commands that are part of the Z Wave system Refer to your controller s instructions as to whether your controller can transmit those commands ADVANCED OPERATION All On All Off The2. any other neutral If multiple neutrals are tied together in one box separate the neutrals to preserve the integrity of the ZRW113 circuit Caution Do not wire unit live with power on the circuit and do not allow the yellow wire to contact line voltage neutral or ground or you will damage the device see the ZTH100 Wireless Controller operating instructions to add this module under the command of the Wireless Controller HomePro 0766 01 Z Wave ZRW 113 Instructions Series 200 Release 2 2 by ADVANCED CONTROL TECHNOLOGIES INC 1 P D 011008 INCLUDING ZRW113 TO THE NETWORK STEP 1 Prepare the Controller to include a unit to the network by adding it to a group method of adding a node to the network Refer to controller instructions STEP 2 The ZRW113 must be in its permanently installed location Tap either the top or bottom of the ZRW1130nce STEP 3 You should see an indication on your Controller that the DEVICE WAS INCLUDED in the network NOTE If you have trouble adding the ZRW113 to a group it may be that the Home ID and Node ID were not cleared from it after testing You must first RESET UNIT with your controller to remove it from the network If using the ZTH100 select MENU scroll to SETUP and scroll to RESET UNIT Although adding it to a group includes it in the network removing it from a group does not remove it from the network If removed from a group it functions as arepeater only
3. HomePro us RF Home Automation Z Wave Radio Frequency RF Controlled 120 VAC Isolated Contact Wall Mounted 3 Way Switch Series 200 Release 2 2 to Neutral ZRW113 ASI L s and Load a must share the same proprietary Neutral Z N or to Line 24 to 277V White Neutral White w Red Strip a PON 12QVAC ooo n l z Black Blue maximum 1 Line Shown with supplied Decora trim plate lt Push O Yellow 3 Yellow Push 0 l Push top or th 2 bottom of paddle to configure C i Oo Scored Tab Cc Will break flush Note This module must be Included in the Network only oe E where it will be permanently installed The proper operation of this node in the mesh network is dependent on it knowing its location with respect to other nodes You cannot test bench configure this module then install ZRW113 WALL MOUNTED SWITCH The ZRW113 Isolated Contact Wall Mounted 3 Way Switch is a component of the HomePro lighting control system Wire the Wall Mounted Switch in place of the standard wall switch according to the diagram above and program from the Wireless Controller to operate loads Inclusion of this Switch on t
4. The Static Controller can act as a gateway in the system since other nodes always know its position not moved after addition to the network The always listening advantage of the Static Controller is that other nodes can transmit information frames to itwhenever needed You can assign an SUC Route to the ZRW113 Refer to your controller s instructions on how to do this if it supports it Assigning an SUC Route to the ZRW 113 allows it to request an update of the Z Wave devices that are between it and the Z Wave device to which it was trying to transmit The ZRW113 will only request an update when a transmission fails SPECIFICATIONS Power 120 VAC 60 Hz Signal Frequency 908 42 MHz Maximum Load Isolated Contacts 20 amps 5440 watts maximum 277 VAC Motor 1H P maximum 120 240 VAC Incandescent TV8 Tungsten 120 VAC 960W maximum Range Up to 100 feet line of sight between the Wireless Controller and or the closest HomePro Receiver Module INTEROPERABILITY WITH Z WAVE DEVICES A Z Wave network can integrate devices of various classes and these devices can be made by different manufacturers just as the ZRW113 can be incorporated into existing Z Wave networks The top or bottom of the paddle switch on the ZRW113 can be used to carry out inclusion adding to the network by adding to a group association operate simultaneously with other nodes exclusion remove from a group or reset remove from the net
5. ZRW113 supports the ALL ON ALL OFF commands The ZRW113 can be set to respond to ALL ON and ALL OFF commands 4 different ways Refer to your controller for information on how to set the ZRW113 to operate in the manner you desire Some controllers may be only able to set certain settings of ALL ON ALL OFF response The 4 different ways the ZRW113 can be setup to respond to ALL ON and ALL OFF commands are 1 ZRW113 will not respond to ALL ON or the ALL OFF command 2 ZRW113 will respond to ALL OFF command but will not respond to ALL ON command 3 ZRW113 will respond to ALL ON command but will not respond to ALL OFF command 4 ZRW113 will respond to ALL ON and the ALL OFF command Z Wave ZRW 113 Instructions Series 200 Release 2 2 0766 01 HomePro P D 011008 2 by ADVANCED CONTROL TECHNOLOGIES INC Association The ZRW113 supports the Association command The ZRW113 can be setto control other Z Wave devices You can turn on and off and even dim other Z Wave devices once they are associated into either of 2 groups of the ZRW113 Each group is turned on off or dimmed by tapping or holding the switch a differing amount of times If you associate Z Wave devices into Group 2 you can turn those devices on and off by tapping the switch on or off twice You can brighten or dim devices by tapping the switch on or off once and then holding the switch The load attached to the ZRW113 is not affected If you associate Z Wave devices into Grou
6. es Increase the separation between the equipment and receiver Consult the dealer or an experienced radio TV technician for help IC NOTICE This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada Pitehucts ther spice J Aiiren L WA gahar baher Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interfer ence that may cause undesired operation of the device Z Wave ZRW 113 Instructions Series 200 Release 2 2 0766 01 HomePro P D 011008 4 by ADVANCED CONTROL TECHNOLOGIES INC
7. he ZTH100 Wireless Controller menu allows remote ON OFF control of lamps connected This Wall Mounted Switch is designed to work with other Z Wave enabled devices Z Wave nodes of other types can be added to the system and will also act as repeaters if they support this function of repeating the signal received to other modules in the system As part of a Z Wave network the ZRW113 will also act as a wireless repeater to insure that commands intended for another device in the network are received This is useful when the device would otherwise be out of the radio range of the wireless controller There are no field repairable assemblies on this unit If service is needed the unit must be returned where purchased DANGER SHOCK HAZARD Read and understand these instructions before installing This device is intended for installation in accordance with the National Electric code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada It is recommended that a qualified electrician perform this installation Make sure the load controlled by the switch does not exceed 5540 watts For indoor use only Retain instructions for future use INSTALLATION Wire the ZRW113 in place of a current wall switch according to the diagram above When used AS101 s are required to be wired to the same line or neutral which is also wired to the master unit as well as the load being controlled and not wired to
8. ngth 1 Byte e Valid Values 0 or 1 default 1 Night Light The LED on the ZRW113 will by default turn ON when the load attached is turned ON To make the LED turn ON when the load attached is turned OFF instead set parameter 3 to a value of 1 e Parameter No 3 e Length 1 Byte e Valid Values 0 or 1 default 0 Invert Switch To change the top of the switch to OFF and the bottom of the switch ON set parameter 4 to 1 e Parameter No 4 e Length 1 Byte e Valid Values 0 or 1 default 0 LED Transmission Indication The ZRW113 will flicker its LED when it is transmitting to any of its 2 groups This flickering can be set to not flicker at all Set to 0 to flicker the entire time it is transmitting set to 1 or to flicker for only 1 second when it begins transmitting set to 2 By default the ZRW113 is set to flicker for only 1 second e Parameter 19 e Length 1 Byte e Valid Values 0 1 2 default 2 Each Configuration Parameter can be set to its default setting by setting the default bit in the Configuration Set command See your controller s instructions on how to do this and if it supports it All Configuration commands will be reset to their default state when the ZRW113 is RESET from the Z Wave system HomePro 0766 01 Z Wave ZRW 113 Instructions Series 200 Release 2 2 by ADVANCED CONTROL TECHNOLOGIES INC 3 P D 011008 SUC Support There must be a Static Update Controller in your Z Wave system for this feature to work
9. p 3 you can turn those devices on or off by tapping the switch on or off three times You can brighten or dim devices by tapping the switch on or off twice and then holding the switch The load attached to the ZRW113 is not affected You can associate up to 5 Z Wave devices into each of these groups For instructions on how to associate a Z Wave device into one of these groups refer to your wireless controller instructions If you are using the ZTH100 controller refer to the Setup Menu Association section ANOTE ABOUT DIMMING If you combine Z Wave enabled dimmers and other types of Z Wave devices ina group place a Z Wave enabled dimmer into the empty group 1 to ensure that the dimming operates correctly Configuration The ZRW113 supports the Configuration command The ZRW113 can be configured to operate slightly differently than how it works when you first install it Using the Configuration command you can configure the following You can use a ZTH100 to send Configuration commands Refer to the Setup Menu Configuration section Set Ignore Start Level Bit When Transmitting Dim Commands The ZRW113 can send Dim commands to Z Wave enabled dimmers The Dim command has a start level embedded in it A dimmer receiving this command will start dimming from that start level if this bit is set to 0 If the bit is set to 1 the dimmer will ignore the start level and instead start dimming from its current level e Parameter No 1 e Le
10. work Controllers can be replicated in order to provide operation from various locations WARRANTY For warranty and general product information visit our web site at www act solutions com ABOUT ZRW113 S CERTIFICATION The ZRW113 is certified to comply with applicable FCC and IC rules and bed Industry regulations governing RF and EMI emissions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful C US interference and 2 This device must accept any interference received Federal including interference that may cause undesired operation LISTED eo anaes FCC NOTICE Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measur
Download Pdf Manuals
Related Search