Instruction Manual
Contents
1. screw with spring plain lock washer Nominal size 3 1 External tooth lock washer Nominal size 4 1 Specifications B1797 Power cord 3 wired 220V KTL CE cord amp European plug B B1798 Power cord 3 wired 240V or Grae Austaienpug cord amp BS plug Replacement parts Specifications A1515 Heating element 100 120V A1516 Heating element 220 240V A1517 Solder pot 50 x 50 x 42 mm 1 97 x 1 97 x 1 65 in a B2932 Spatula Optional parts A1518 Solder pot 75 x 75 x 55 mm 2 95 x 2 95 x 2 17 in2. the current set temperature will remain displayed In the input mode establish the entered value and exist the data input mode H Holding down the button for one second or more will enter into the offset input mode If the button is otherwise pressed for only less than one second the current offset value will remain displayed 6 PARAMETER SETTINGS Before changing the setting temperature The HAKKO FX 301 comes from the factory with the following values preset C or F temperature display 1C C selection Setting a solder type Sn Pb Tin an lead Setting the solder pot type 50 x 50 square OFF or disabled Entering the parameters 1 C or F temperature display selection 2 Setting a solder type Once a solder type close to the applicable one as shown in the right side the temperature con trol will be performed for that solder type Operation 1 Turn the power switch ON 2 The temperature set at factory is displayed The temperature was set to 350 C at factory 3 The temperature control is started causing the temperature to increase NOTE The display blinks when the power is turned ON or when settings are changed This blink ing occurs because the temperature control is in progress The current temperature will be displayed in a short time The HAKKO FX 301 has the following four parameters 1 C or F temperature display selection 2 Setting a solder type 3 Setting the solder po
3. E IS DEFFERENT Entering offset value The offset value was set to 0 C at factory Range of values C 70 to 70 C F 158 to 158 F Example When the set temperature is 400 C and the ac tual solder temperature in the solder pot is 350 C The difference between the two is 50 C Therefore enter 050 instead of the cur rent offset value Once you can check the display and the measured temperature all the settings are finished When the temperature of solder reaches the set value the buzzer sounds About 5 to 10 minutes later measure the temperature of solder If the measured value is different from the displayed tem perature match them with each other by entering an offset 9 MAINTENANCE Press the 3 button and Al nr tern hold for one second ZIN Press the button a Soeeeees Y sly sly MII Press the or button ME M LILI gt JU ZIN ZIN Press the button l a oe eceeeeeae J 1 Y slz MET p he b ngn GOL Pressthe buton a ZIN NOTE When measure the temperature of the solder be sure to measure at the same position AN WARNING Unless otherwise directed carry out these procedures after turning the power switch OFF unplugging the power plug and waiting for both the unit and the solder to sufficiently cool down CAUTION After changing the solder pot measure the tem perature again If the measured value is different from the displayed tem
4. HOOTING GUIDE e Before checking the inside of the FX 301 or replacing parts be sure to disconnect the power plug The unit does not operate when the oO power switch is turned on ACTION oO ACTION 12 PARTS LIST Truss screw M3 x 8 4 Button bolt M4 x 35 2 Pan head screw M3 x 4 12 g i A j A Pan head screw FX 301 Soldering pot o B eva o o B218 Overflowvay B2916 Heatinsulator Cd B2921 P W B For temperature E ee einer a B2927 Solder potsuppot B2928 Solder pottray Cd a B1084 Powerswich Cd 2 B1134 Fuse holder Cd B1795 Power cord 3 wired 100 220V E _ B1796 Power cord 3 wired 230V a fenu ee B2913 Power cord 3 wired 230V India Oe eaa B2914 Power cord 3 wired 220V China cord amp Chinese plug Is the power cord and or the connection plug disconnected Connect it Is the fuse blown Investigate why the fuse blew and then replace the fuse If the cause can not be determined replace the fuse If the fuse blows again send the unit in for repair Truss screw M4 x 5 12 External tooth lock washer Nominal size 4 2 Pan head screw with spring plain washer M4 x 8 4 External tooth lock washer Nominal size 4 1 Plain washer M3 4 Pan head screw M3 x 10 4 Pan head screw with spring washer M4 x 6 1 Pan head
5. Square Setting range of temper atures 200 450 C 400 840 F 75 x 75 Square Setting range of temper atures 200 380 C 400 720 F Press the or to select the number corre sponding to your solder pot size as shown above After checking the displayed selection press the xX button for OFF or disabled for a value between 10 and 9990 hours Select the displayed and then press the button You will proceed to enter the time to set Enter a desired time value Time can be set in units of 10 hours in a range be tween 4G i and 10 and 9 990 hours After entering the time value press the button NOTE After the set time has passed will be dis played the alarm will start sounding and then the heater for the solder pot will be turned OFF To reset the alarm and others turn OFF the power switch and then immediately turn it ON again The timer will be reset to the above time set ting After the set time has passed the heater for the solder pot will be turned OFF Changing the time Enter the value between 001 999 Resetting the time ln case of resetting the time in the middle of setting the time please change to the different value once and en ter the desired value 7 CHANGING THE TEMPERATURE SETTING Changing the temperature setting The HAKKO FX 301 is preset at 350 C at the factory Example 350 C to 400 C 1 Check that the displayed value is 350 C Press the but
6. WHAKKO FHAKOFX 301 SOLDERING POT Instruction Manual Thank your for purchasing the HAKKO FX 301 soldering pot Please read this manual before operating the HAKKO FX 301 Keep this manual readily accessible for reference 1 PACKING LIST AND PART NAMES scroware incudedin the package MI cece ssa tesa suze eectet esata ree eein 1 Hexagon WIGIICIN cc ctccecetececsceted ea eseeeete ec ate cused 1 Spatula eseist pain aai Eana E ne 1 Instruction manual cee te cece cee 1 J shaped waste collector 1 Solder pot Hexagon wrench Spatula J shaped waste collector Display Solder pot mounting screws both sides Power switch Control buttons Fuse 2 SPECIFICATIONS 100V 200W 110V 260W 120V 310W 220V 240W 230V 260W 240V 280W 200 450 C 400 840 F 200 380 C 400 720 F 50 W x 50 D x 42 H mm 2 0 x 2 0 x 1 7 in 75 W x75 D x 55 H mm 3 0 x 3 0 x 2 2 in 0 85 kg 1 87 Ib 1 2 kg 2 64 Ib Weight 1 7 kg 3 74 Ib w o solder and cord 143 W x 100 H x 220 D mm 5 6 x 4 0 x 6 7 in Only a 50 x 50 square solder pot is included in this product The 75 x 75 square solder pot is an optinal part Specifications and design are subject to change without notice QHAKO FHAKKO CORPORATION HEAD OFFICE TEL 81 6 6561 3225 FAX 81 6 6561 8466 http www hakko com E mail sales hakko com Please access to the following addres
7. perature enter an offset WARNING When the power is ON the temperature of the melted solder in the solder pot is approximately 450 C 842 F Before changing the solder pot be sure to unplug the power cord and let the solder and the unit cool to room temperature Replacing the heating element 10 ERROR MESSAGES Sensor Error 1 Using the hexagon wrench provided with the HAKKO FX 301 to loosen the screws on both sides of the unit NOTE Removal is unnecessary 2 Pull out the solder pot 3 Insert a new solder pot and then tighten the screws on both sides Z CAUTION Check that the solder pot has been locked now Otherwise the temperature may not in crease properly 1 Loosen the screws on both sides of the unit Fig 1 NOTE Removal is unnecessary 2 Pull out the solder pot Fig 2 3 Remove the setscrews 6 pieces on the unit Fig 3 4 Slide the front panel frontward remove the connec tor Fig 4 on the connector circuit board and then pull out the unit of the heating element Fig 5 5 Insert a new heater unit and then install it by re versing the above steps After finishing the maintenance measure the tem perature of solder If the measured value is different from the display temperature enter an offset There is the possibility that a failure has occurred in the sensor circuit The power is shut down with the buzzer sounding continuously 11 TROUBLE S
8. s for the other Sales affiliates http Awww hakko com address 2005 2 Copyright 2005 HAKKO Corporation All Rights Reserved MA01375JZ050202 3 SAFETY INSTRUCTIONS AN WARNING Warnings cautions and notes are placed at critical points in this manual to direct the operator s attention to significant items They are defined as follows WARNING Failure to comply with a WARNING may result in serious injury or death Z CAUTION Failure to comply with a CAUTION may result in injury to the operator or damage to the items involved Two examples are given below A WARNING When the power is ON the temperature of the melted solder in the solder pot is approximately 450 C 842 F Before changing the solder pot be sure to unplug the power cord and let the solder and the unit cool to room temperature Observe the following precautions to ensure safety Z CAUTION The molten solder in the solder pot is dangerous since it reaches about 450 C 842 F The pot cover also becomes a high temperature when the power is ON Wrong handling may cause burns or fire Be sure to observe the following precautions Use this product on highly stable metal workbench Never use it near paper or other flammable materials Inform others in the area that the product is hot and should not be touched Never put water in the solder pot as this will cause solder to spatter out of the solder pot Turn the power off when not in use or left
9. t type 4 Setting the timer Once you enter the parameter setting mode the setting sequence will start in the following order Af ter all the parameters have been set the displayed temperature setting starts blinking and the temper ature of the solder pot starts rising 1 Turn the power switch OFF 2 Press and hold down the and QD buttons si multaneously and then turn the power switch ON 3 When you enter the parameter setting mode is displayed 4 Press the or button to select for C orl F for F After checking the displayed selection press the 2 button After establishing the temperature unit to use enter the solder type selection mode Press the or button to select the number cor responding to your solder type as follows Sn Pb Tin an lead Sn Ag Cu Tin silver and copper Sn Cu Tin and copper Sn Tin After checking the displayed selection press the button NOTE The solder types are listed for only rough classifi cation Select the closest one to your solder type 6 PARAMETER SETTINGS 3 Setting the solder pot type In the HAKKO FX 301 package the size of the solder pot is 50 x 50 square The 75 x 75 square solder pot is available to order for the require ment of your work 4 Setting the timer It will be able to check the present addition time by pressing the button How to change and reset Set the size of the solder pot that you will use 50 x 50
10. ton for one second or more The hundreds digit will start blinking indicating the unit is in the temperature setting mode 2 Entering the hundreds digit Press the or button to set the desired fig ure When the desired figure is displayed press the button to enter The tens digit will begin to blink 3 Entering the tens digit Press the or button to set the desired fig ure When the desired figure is displayed press the 3 button to enter The unit s digit will begin to blink 4 Entering the unit s digit Press the or button to set the desired fig ure When the desired figure is displayed press the button to enter Now the setting has been completed After the setting has been completed the displayed temperature starts blinking and the temperature in the solder pot starts rising The current temperature will be displayed in a short time Press the button anda K en m iy C ZS I Press the or button k NI NI LIE I Press the button once LIC nese Orme a EAE S ZIS 1 Press the or button d sly NZ LIO Press the button once IMT ait CS gt Ie ZIN ZIN Press the button once f wre BITIT NOTE For the 50 x 50 square pot the setting range of temperatures is between 200 450 C 400 840 F For the 75 x 75 square pot the setting range of temperatures is between 200 380 C 400 720 F 8 IN CASE THE DISPLAY AND THE ACTUAL TEMPERATUR
11. unattended Before changing parts or storing the unit be sure to turn the power off and allow the unit to cool to room temperature Observe the following precautions to prevent accidents or damage to the unit Do not use the HAKKO FX 301 for applications other than soldering Do not modify the HAKKO FX 301 Use only genuine HAKKO replacement parts Do not allow the HAKKO FX 301 to become wet or use it with wet hands Be sure the work area is well ventilated Soldering produces smoke Do not do anything else that might be dangerous 4 INTIAL SETUP 1 Install the J shaped waste collector to the unit Three way installation is possible to meet your operating needs 2 Cut the solder sticks into small pieces and put them in the solder pot 3 Plug the power cord into a grounded wall socket CAUTION Make sure the power switch is off before plugging in the power plug This product is protected against electrostatic dis charge Make sure this product is grounded before using 5 OPERATION Display and operation Display The front panel of the HAKKO FX 301 soldering pot has the following controls Increases the value in the appropriate display window D decreases the value in the appropriate display window gt Holding down the button for one second or more will enter into the temperature setting mode If the button is otherwise pressed for only less than one second
Download Pdf Manuals
Related Search