Home

UPS WEB/SNMP MANAGER

1. 0 Note All network components such as routers hubs etc need to be full UPS supported as it is otherwise not possible to reach all clients during the network shutdown e Installation of the RCCMD client You find a setup procedure for RCCMD on the UPS Management Software CD or downloadable from www generex de The RCCMD Setup contains a wizard which guides you through the installation At the first window you have to enter the IP address of the adapter from which the client receives the RCCMD shutdown signal Confirm the following pre settings and mind the shutdown file at the ultimate window Press Configure to edit the actual shutdown sequence at the client Alternatively you can also edit the batchfile to add or change the actions to be executed Finally press Install to complete the configuration and to start the RCCMD service Note Each RCCMD installation needs its own licence code Usually the CS121 package contains at least one licence depends on the model Contact your UPS dealer to obtain further licence codes e Configuration of the adapter s event settings Call the menu Events amp Alarms at the adapter s HTTP configuration click on the event Powerfail and press the button Add new job to open the CS 121 s Job Editor There choose as function from the drop down menu the option Send RCCMD Shutdown to remote client and enter the IP address of the client the listener
2. PreAlarm Analog Input 1 Low Job Type When Parameter 1 Parameter 2 1 Edit Del Test Log 0 PreAlarm Analog Input 1 Low Job 1 2 Edit Del Test RCCMD Trap PreAlarm Analog Input 1 Low Job 2 Add new job Back to event overview Figure 33 HTTP Event Editor The Event Editor allows you to edit delete and test existing events as well as to add a new event job Just click on the desired action to enter the Job Editor who lets you make the configuration 4 4 1 Events Please call the menu Events Alarms in the Web browser to open the main configuration site whereon all configurable events are listed 4 4 1 1 concerning the UPS In the Sitemanager s menu Event overview you see on top a couple of events concerning the state of an connected UPS usually numbered from 1 Which events are actual available depends on connected UPS model In the following we introduce the main and important events which should be handled in general if a UPS is connected to the Sitemanager e Powerfail The event Powerfail will be released when the UPS has lost the power supply This event is usually used to proceed operations like backup strategies batch files to be executed on client stations etc pp You can configure such jobs with the Remaining time parameter to ensure the actions will be executed completely e System shutdown The event system shutdown will be released if the configured Syste
3. EMAIL info generex de WEB www generex de This and all other product datasheets are available for download Outlets Port Name PowerOn Ti Port Name Pp outlet E outlet C Outiet E 0 Flashlight E outlet E 5 Outlet C Outlet E outlet E Figure 22 HTTP configuration Outlets Furthermore it is possible to attach a timer value to each Outlet This determinates how long an outlet will be switched in seconds Set the timer value to 0 if the outlet is to be switched without any time limit application example To switch on a buzzer for a specific timeframe O Note If you do not want to use a name for the Analog Digital Inputs or rather the Outlets please set the following into the single name area amp nbsp 4 2 Alarm matrix The following Alarm Matrix gives you numerous possibilities to configure dependencies between different alarm states and to join them to different outlets This makes it possible to process an alarm scenario in dependency of the state of several input sensors For example An alarm scenario is to be released only if two temperature sensors are out of range or if the air condition is not active Alarm Matrix i i 3 HAI Ee ef ow 5 EL 4 Hn ee BBS oh Bef ok ABE 4664 a JE s 404 Ta a E E EAE d 4 ORASI Ee Bt Hn ae Be at Hn oe ORR TRR TRR A EE whe EE E EE Eg EE Eg Bf E p BS oh To oco 2G aoe Alarms 5 E E ee E E
4. English Manual 1 About the SITEMANAGER II v3 1 1 General information 1 2 Features 2 Installation 2 1 Connectors and connections Rev A 2 1 1 Analog input at RJ12 connectors 2 1 2 Analog input at open sockets Rev A 2 1 3 Digital input connectors Rev A 2 1 4 Switchable relay outputs 2 2 Status LED s 3 Getting started Basic settings 4 Configuration 4 1 Connected devices 4 1 1 at analog input 4 1 2 at digital input 4 1 3 at digital outputs relays 4 2 Alarm matrix 4 3 Status display 4 3 1 Input Output status 4 3 2 gChart 4 4 Event configuration 4 4 1 Events 4 4 1 1 concerning the UPS 4 4 1 2 Notification via SMS 4 4 1 3 concerning the Sitemanager II v3 Inputs Outputs 4 4 2 Email Job 4 4 3 RCCMD Perform shutdown signals to network computers Appendix A SITEMANAGER II v3 technical data B Pin layout for Input sockets C Syntax for switching of the outputs Table of figures Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download 1 About the SITEMANAGER II v3 1 1 General information The SITEMANAGER Il v3 is a professional building management device which contains 8 configurable analogue inputs 0 10V or 0 4 20mA 8 digital inputs for smoke fire intrusion and other
5. WEB www generex de This and all other product datasheets are available for download Analog Inputs Port Name Low High Sensor Range Unit Sensor Type Alarm 1 Temperatur Rack 40 42 D 100 j i SM_ILT_H 2 Luftfeuchte Rack 15 AT 0 100 relF SMITH 3 Temperatur Serverraum 8 v 37 o 100 6 SM_IL_T_H 4 Luftfeuchte Serverraum 12 45 0 100 relF SMILTH 5 Analog Input a E 100 o 100 ac Custom 0 140V 6 Analoginput gt gt 0 EO 100 0 100 C Custom0 10V 7 Analoginputt 0 A A Hw Ho 7100 Mec Custom 0 10V 8 Analog Input 0 E 100 Fl o 100 gt Custom 0 40V Hysteresis 3 Lograte 180 Seconds Apply Figure 28 Configuration of the thresholds of the analog Inputs The CS121 firmware version 4 26 x provides the option to define threshold events for the analogue inputs Click the Configure Threshold Events button into the CS121 Events Alarms menu Device Status UPS STATUS OK Sensor Status lt 7 i 5 4 Threshold Events Threshold Events 1 SM_analogue 1 lt 13 00 EditEvent Delete Event Edit Jobs 2 SM_analogue 1 gt 47 00 EditEvent Delete Event Edit Jobs Add Threshold Event System amp N
6. at analog input On the top of the SiteManger II v3 configuration page you see the section Analog Inputs for the settings for the 8 anlog inputs 15 Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download Analog Inputs Port Name Low Low High High Sensor Range Unit Sensor Type Alarm PreAlarm PreAlarm Alarm 1 Seneraum7Tempeatur fia fis fo a fp foo Fo fem Ra E 2 Seneraum Lutfeunte fio 2 fas far fo fioo eer emt Rem By 4 fanaoginnt fo fp 0 fp C foes O fan fro fe emr py 7 Phogat pP Cp Cp Ces DC p ps Pe custarmo 1ov a momi e Oe dss Oe e Fe i eom N Hysteresis 3B Lograte heo Seconds Apply Figure 20 HTTP configuration Analog Inputs Beside the name of the input you also define here as shown above the alarm tresholds the sensor range and the measurement unit Note that the alarm values low and high are only active if the fields beside the alarm values are enabled In the drop down menu Sensor Type some basic sensor models are already listed which you can choose to set predefined values for these types select Custom to make divergent or individual settings You can calibrate every sensor with the Sensor Range that means if you want to rise a measured value for 5 C just modify the
7. 20mA A R ckseite Anschl sse A Channel8 Channel Channel 6 _ in a j l ai a KHeHe a hannel4 Channel3 Channel2 Channeli It Pi it n an WW nm w fb Frontseite NY Figure 9 Jumper positions of the analog inputs 0 20mA 4 20mA Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download 2 1 3 Digital input connectors Rev A Underneath of the analog input sockets the bank for the 8 digital input sockets is located D01 D08 Figure 10 Analog input sockets bank above A01 A08 and digital input sockets bank below D01 D08 Please follow the circuit examples as shown below for the pin assignment of the digital input sockets SITEMANAGER II Digital inputs digital inputs digital inputs B Ground input switched open approx 12 Input switched closed approx 10mA Figure 11 Pin assignment of the digital input sockets 10 Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download ATTENTION Connection sockets have changed Before activating the device notice the following The Digital a
8. Pow Figure 1 SITEMANAGER II v3 front side e Complete CS121 functionality e 8 configurable analogue inputs 0 10V or 0 4 20mA e 8 digital inputs e 8 switch outputs 4A 250 VAC e Remote configuration e LED status display e 19 chasis only 1 HE e Configuration via Web interface e Email support SNMP FTP Modbus over IP e UPS interface Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download 2 Installation Sensors for temperature humidity I pressure levels 8 configurable _ voltage analogue inputs i currency etc pp IP Network LAN WAN 8 configurable je Digital input for digital inputs 3 fire i 8 switchable outputs ator eVGA BI Ny intrusion UPS _ Q door contact etc pp Figure 2 SITEMANAGER II v3 with UPS The figure above shows a typical installation of the SITEMANAGER IlI v3 with a UPS connected Imagine that a numerous kind of sensors can be connected to the SITEMANAGER Il v3 and it is possible to manage all kind of current consuming devices by switching the outputs 2 1 Connectors and connections Rev A The backside of the SITEMANAGER II v3 incorporates the following connectors as shown below m AB AB AB AB AB AB AB AB past ae ne 12
9. analog input RJ11 Game RT SM_ILT ee h c ae a SN_ILVMC a Ph Bo SMI CMC and all other types Sa Pus SM_ILVMC wa SH_ILCMC SM_IL Dic Figure 5 Sensor connections at the analog input RJ12 2 1 2 Analog input at open sockets Rev A SM_ILT SMI PLUS gt SM I VMC SM Il CMC While the RJ12 connectors are unused the analog input is also available at the open sockets A01 AO8 Figure 6 Analog input sockets See the following figure how to assign the pins Mind that the input signal must be in the range between 0 10V DC Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download SITEMANAGER II Analog inputs analog input Temperature Figure 7 Pin assignment of the analog input sockets Configuration of the analog input sockets of the SiteManager II v3 Rev B from SN SMGO5 00411 Every of the 8 analog input sockets provide the readout of the analog measurement values from 0 10V delivery state 0 20mA or rather 4 20mA It is required to get the jumpers of the relative analog input socket of the main board into the accordant position Please do the following if you want to change the delivery state ATTENTION This should be done by qualified personnel only Pull off the power supply of the SiteManage
10. default range from 0 100 to 5 100 Therefore you are able to adjust the measurement values like a gauged thermometer With the field Hysteresis you define the scope within the defined value can oscillate without releasing an alarm This is important e g for temperature measurements which are not increasing decreasing continuously At Lograte you can set the loop time in sec in which the measured values will be written into the logfile 4 1 2 at digital input The 8 digital inputs can be configured within the following section Digital Inputs NC Contact Active Port Name Manual Switch E M igital Input 5 D Magnetic Contact al Digital Input 6 Di gital Input 7 z m 3 Motion Detector mW W 4 Digital Input 4 E E 8 Digital Figure 21 HTTP configuration Digital Inputs Name the connected devices and set whether the contact is closed or not in its normal operating mode Field NC Contact Enable Active for all connected devices 4 1 3 at digital outputs relays The SITEMANAGER Il v3 contains 8 digital outputs which can be switched depending on various events and settings Within the section Outlets you give each connected device a unique name and set whether the relay is to be closed or not in normal operating mode PowerOn 16 Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910
11. to configure the thresholds for releasing UPS specific events individual CS121 also supports these features if the UPS includes this possibility e Continuous periodic events To define an event job which will be executed continuous e g daily create a job on the event JPSMAN started as in the following figure UPSMAN started Job 2 Function Send an EMail v When Immediately once Receiver someone somewhere com D Scheduledin 0 seconds Seperate receivers by comma to send mail to more then one receiver Do not insert additional spaces Text UPSMAN at 192 168 200 1 started ee 00 ee Use text as subject a v D After 0 seconds After 0 seconds amp repeat After 0 seconds on battery DJA 0 seconds remaining time Figure 34 HTTP Job Editor Continuous event job For example the configuration as shown above causes that each day is equivalent to 86400 seconds an email to someone somewhere com will be sent until the SiteManager Il v3 is in normal operating mode 4 4 1 2 Notification via SMS From firmware version 4 17 x or higher is a new function available which offers a notification via SMS Just use a simple 1 1 cable for the connection of the SiteManager II v3 and the GSM modem UPSMAN started Job 1 Function Send SMS with GSM modem Phone Number Write to Loafile Send an EMail Message Send RCCMD Shutdown to remote client Send RCCMD Message to remote client 5 set to GSM Modem
12. trio alarms and 8 switch outputs 4A 250 VAC The analogue inputs can be used to connect sensors for humidity temperature and other sensors All measured data and status conditions of the digital inputs can be requested from a network interface The input range of the analogue inputs can be easily adjusted for the different sensors using the web browser configuration The controlling of the switch outputs is achieved via the different control commands of the SiteManager II v3 web interface The SITEMANAGER Il Vv3 also has an internal time clock and logs all events and regular measurements with date and timestamps The precision and exactness of the time can also be controlled using the SITEMANAGER Il v3 ability to synchronise its clock with up to three different timeservers either in the internet or within the local network using SNTP or RFC868 These logs can also be read out as pure text or graphed for visual investigation using the SITEMANAGER II v3 built in gChart controller The processing and controlling of the SITEMANAGER II v3 can also be done with the UPS Management Software Webbrowser and other SNMP systems The status of all inputs and outputs is displayed using LEDs built into the front panel of the unit The SITEMANAGER Il v3 is designed as a 19 inch slot that allows for integration into 19 inch racks or for the mounting into separate 19 inch wall units 1 2 Features CET es e t__sees Sess ie CC SiteManager b U
13. E e E E Ee E E E ee E E E ee E E E e E E E ee E E E e E ORO TT ORO RT E E e E E E E E E E ee E E E e E 7 i To OCA s A ano0 E E GG o Gp BE See ee oe iOO GG GGG gt AS 6 Go Gp AS GG oa gt A GG Gay E E EE E Gay E E E EE Go Gis E E ee E eo a E E Go Gis E EEEE Ga E E GG E G E E 6 Go M E E EEE E G Figure 23 Alarm matrix Marker configuration In the figure above is shown the alarm matrix with its 8 markers to be set or unset Each marker thereby is a new state on which specific alarm scenarios can be released 17 Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download For example In the figure above is defined that the Marker1 will be set when at the analog input 1 or 3 an alarm occurs Enabling the field Marker Inverted causes that Marker1 will be unset in case of an alarm at analog input 1 or 3 Furthermore marker 2 will be set when at the digital inout 2 and at the analog input 2 an alarm state accurs at the same time Means that an alarm at just one input is not sufficient for setting marker 2 Accordingly it is possible to set or unset each marker in dependency of different digital and or analog input states After having defined the conditions when markers are to be set res
14. Pin 2 Analog Channel 5 0 10V Pin 3 Analog Channel 6 0 10V Pin 4 GROUND Pin 5 SM_Il_DIG Sensor1 Input Pin 6 SM_Il_DIG Sensor2 Input Sensor Input 4 Pin 1 12 VDC Pin 2 Analog Channel 7 0 10V Pin 3 Analog Channel 8 0 10V Pin 4 GROUND Pin 5 SM_Il_DIG Sensor1 Input Pin 6 SM_Il_DIG Sensor2 Input Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download 29 C Syntax for switching of the outputs Set the RCCMD client at port 6002 to on and restart it Install the RCCMD Windows Wizard and open a DOS box The following is a syntax example with the IP address 192 168 202 165 Ce XV RCCMD Fecmo 5 a 192 168 222 238 p 6002 se EXECUTE UPSEMD 20000 1 4 ATTENTION The blank after the Execute is important Common syntax for the switching of the outputs of the SiteManager UPSCMD Z20000 1 0 output L to bow UPSCMD 20000 iy d output to shag UPSCMD ZO0Q000 25 0 Ou Gp lt 2 co Low URSCMD 20000 2 1 omtput 2 to high PURSCMD 20000370 OULRDUE 3 to Low PURSCMBD 20000 37 1 OUEDUE sto high UPSCMD 20000 4 0 output 4 to low UPSCMD 20000 45 1 cutput 4 te high UPSCMD Z0000T5 0 output 5 to low UPSCMDLZOCO0 S k Gatu TO bigh UPSCMD 20000 670 cubpUut 6 to bow UPSCMD 200 00
15. Send RCCMD Command to remote client Shutdown UPS Switch AUX SensorMan UPS Output Send RCCMD Trap Send Wake On LAN Magic Packet Send RAS Notification Send SMS with GSM modem Figure 35 HTTP Job Editor Send SMS with GSM modem Set the telephone number of the receiver and the text into the accordant areas LED Status Display Operating Status LED Signaling SIM card not present Slowly red flashing SIM card active Fast red flashing 25 Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download Figure 36 Siemens GSM TMA T35i modem Into the menu System amp Network Status you can see the signal level of the modem to adjust your antenna optimal Green means a good signal is present System Info amp Network Status CS121 Hardware C9131 Location CS121 Firmware CS121 SNMPv4 17 12 090831 System Name CS 121 HyNetOS Rel 2 4 1 32 pduc Aug 27 2009 System Contact I Target Server Rel 2 4 1 15 pduc Aug 08 2009 Attached Devices UPS protected devices SS oe ee System Time 02 09 2009 12 17 07 UPS driver 714 Uptime 0 days 0 hours 10 minutes 3 seconds UPS Manufacturer Generex Total Uptime Approx 0 days 0 2 hours UPS Model smart offline UPS GSM Signal Quality 109 53 dBm Network Status MAC Address 00 03 05 0E 07 19 Tel
16. VDC DIP COM 1 12 a ES LJ LEE LCE gt a Figure 3 Backside of the SITEMANAGER IIl v3 e Power supply Connect the included external power supply unit DC 12V e DIP switch 1 2 With the DIP switches it is possible to change between configuration mode and normal operating mode How to use the DIP switches please follow the instructions in section 3 Getting started Basic settings e COM 1 port If necessary connect the UPS with the original vendors UPS cable e LAN connector Connect the SITEMANAGER II v3 with an RJ45 cable to the network e LINE Port for external RAS service e 4 RJ12 connectors containing 8 analog inputs channels for sensors and other measurment units e 8 digital and 8 analog input sockets e 8 switchable relay outputs Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download 2 1 1 Analog input at RJ12 connectors Sensor Inputs 2 3 4 Figure 4 SiteManager Il v3 RJ12 connectors The 4 RJ12 connectors contain each 2 analog input channels whereby it is possible to connect 8 analog sensors Please see the figure below how to connect the different sensors at the RJ12 connectors For the pin layout of the input sockets see the particular section in the appendix SITEMANAGER II Sensors at
17. Version 2012 09 06 SITEMANAGER II v3 User Manual English Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download Copyright Statement for Intellectual Property and Confidential Information The information contained in this manual is non conditional and may be changed without due notice Although Generex has attempted to provide accurate information within this document Generex assumes no responsibility for the accuracy of this information Generex shall not be liable for any indirect special consequential or accidental damage including without limitations lost profits or revenues costs of replacement goods loss or damage to data arising out of the use of this document Generex the manufacturer of the BACS products undertakes no obligations with this information The products that are described in this brochure are given on the sole basis of information to its channel partners for them to have a better understanding of the Generex products Generex allows its channel partners to transfer information contained in this document to third persons either staff within their own Company or their own customers either electronically or mechanically or by photocopies or similar means Generex states that the content must not be altered or adapt
18. ant to be able to switch the output 19 Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download SiteManager Il Status Version 2 03 Digital Outputs Digital Inputs Analog Alarms SiteManager 7 2 io A Sie A om oo Ss p COo OCCO OOOO OEO C f 5 6 7 8 5 6 7 8 5 6 7 8 Analog Input Values Alarms 1 2 3 6 7 8 Temperatur Luftfeuchte Temperatur Analog Input Analog Input Analog Input Meetingroom Meetingroom Rack 100 100 100 255 255 255 41 6 rel Alarm ACK Name Alarm ACK Name Rauchmelder Digital Input Digital Input Digital Input Digital Input Digital Input Bewegungsmelder Digital Input Outlets Status Switch Name Status Switch Name Outlet 5 Outlet Outlet 6 Outlet 7 Switch On Outlet 8 Switch Off Outlet Figure 27 Status display with temperature and humidity sensor as well as digital Inputs and Outlets The SiteManager II v3 displays the measurement values of the analog inputs vertical and provides the definition of PreAlarm Thresholds for the low as well as for the high threshold 20 Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de
19. b 1 S tp t o Go Righ UPSCMD 20000 7 0 output 7 to Low URPSCMD Z0000 7 1 output 7 toe high PUPSCMD 200001970 OUTDUE 0 tO Low PURSCMD 20000 3 k OULDUE EO high 30 Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download Table of figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 Figure 15 Figure 16 Figure 17 Figure 18 Figure 19 Figure 20 Figure 21 Figure 22 Figure 23 Figure 24 Figure 25 Figure 26 Figure 27 Figure 28 Figure 29 Figure 30 Figure 31 Figure 32 Figure 33 Figure 34 Figure 35 Figure 36 Figure 37 Figure 38 SITEMANAGER II v3 front side 5 SITEMANAGER II v3 with UPS 6 Backside of the SITEMANAGER II v3 6 SiteManager II v3 RJ12 connectors 7 Sensor connections at the analog input RJ12 7 Analog input sockets 7 Pin assignment of the analog input sockets 8 Jumper positions of the delivery state 9 Jumper positions of the analog inputs 0 20mA 4 20mA 9 Analog input sockets bank above A01 A08 and digital input sockets bank below D01 D08 10 Pin assignment of the digital input sockets 10 Switchable relay outputs 12 Relay outputs 12 Status LED s at HTTP
20. ed in any way without written permission from Generex It is agreed that all rights title and interest in the Generex s trademarks or trade names whether or not registered or goodwill from time to time of Generex or in any intellectual property right including without limitation any copyright patents relating to the Products shall remain the exclusive property of Generex Generex will undertake to deal promptly with any complaints about the content of this document Comments or complaints about the document should be addressed to Generex Systems GmbH Copyright of the European Union is effective Copyright EU Copyright c 1995 2012 GENEREX GmbH Hamburg Germany All rights reserved Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download English Manual Dieses Handbuch ist auch in Deutsch verf gbar Eine aktuelle Kopie erhalten Sie unter download bei www generex de This manual is also available in German To obtain an actual copy please see the download page of www generex de Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download Contents
21. en flashing of the power LED at the SiteManager II v3 front display When the SiteManager II v3 has finished its boot procedure indicated with permanent green lightening of the power LED a network connection can be built up To establish a connection the network must route the SiteManager II v3 answers under 10 10 10 10 to your local host Usually you have to set a temporary route for this Open the command promt and type route print to see the actual routes Use the command route add 10 10 10 10 lt your local P address gt to extend the actual routing table Ping the adapter on IP address 10 10 10 10 and you should receive the answers c Ausw hlen Ch WINDOWS system32 cmd exe gt route print MS TCP Loopback interface Broadcom Netktreme Gigabit Ethernet Paketplaner Miniport Netzwerkmaske Gateway Schnittstelle 46 6 6 192 168 202 1 192 168 2602 51 168 262 51 127 0 0 1 127 0 0 1 192 168 255 255 255 19 2 168 202 51 168 202 511 19 2 168 202 51 255 255 255 255 0 0 0 0 192 168 202 255 255 255 255 255 192 168 2062 51 168 262 51 224 0 0 0 240 0 0 0 19 2 168 202 51 168 202 511 255 255 255 255 255 255 255 255 192 168 202 51 168 202 51 Standardgateway 192 168 262 1 Standige Routen Netzwerkadresse Netzmaske Gatewayadresse Anzahl 16 16 16 16 255 255 255 255 192 168 262 51 1 gt Figure 15 Route command and routing table Connect your Webbrowser MS Internet Explorer and M
22. etwork Status Device Status Device Status Graphic Device Functions SensorMan Status Battery voltage Seconds on Battery Battery Autonomy m Battery charge UPS Temperature Input voltage P N Output load Network amp Security SM_analogue 1 LED Display SM_analogue 2 RAS Configuration SM_analogue 3 Scheduled Actions or aaa SNMP SM_analogue 6 EMail SM_analogue 7 Timeserver SM_analogue 8 UPS Model amp System Figure 29 Configuration of the threshold events of the analog Inputs In this example a below threshold of 13 was defined for SM_analogue 1 in this case for the temperature in C which will appear into the Event Configuration after you executed the Save Exit amp Reboot function 21 Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download Device Status UPS STATUS OK 421 Alarm Marker 4 off 122 Alarm Marker 5 off 123 Alarm Marker 6 off 124 Alarm Marker off 125 Alarm Marker 8 off 126 SM_analogue 1 13 00 127 SM_analogue 1 47 00 J AUX Status Sensor Status C Event Configuration Event Overview Events 98 127 of 127 een ie cma RCOMDS pecu pccun VAi AlAs 98 Alarm Digital Input 1 off 1 0 D 0 0 system amp Network Statu
23. eway Address and Subnet Mask where required also for DNS Server Apply your settings with the button on the right buttom side of the menu Network amp Security Settings MAC Address 00 03 05 13 08 AA Network Card Speed auro x Local Address 192 168 222 176 Gateway Address 192 168 222 100 Subnet Mask 255 255 255 0 DNS Server 192 168 222 100 Use DHCP Cfoooo System amp Network Status Sitemanager lIN3 Status Change Administrator Password Confirm Password Change UpsMon amp SS4 Password a T LED Display Scheduled Actions Confirm Password a SNMP Use UpsMon Password for Web Pages E UPS Model amp System Figure 17 HTTP Basic network settings Ifa UPS is connected at the SITEMANAGER II v3 serial COM 1 it is necessary to set some UPS parameters Therefore call the menu UPS Model amp System and select from the drop down menu the connected UPS model Apply your settings with the button on the right bottom side of the menu Call the menu Save Configuration and choose the option of the same name Set DIP Switch 1 to position ON whereas DIP Switch 2 stays in position OFF Remove and insert the power supply from the SiteManager II v3 to initiate the reboot process See the power LED s to verify the reboot process Reconnect the Webbrowser with the adapter using the configured IP address http lt the adapter s IP address gt If you don t get a
24. ger which has a license to use ROCMD An RCCMD server is found inside any CS121 and is triggering RCCMD clients in case of alarms Therefore RCCMD requires such listeners on each client computer you wish to forward RCCMD signals For installation of RCCMD at client side please see the section in chapter Add on software Note RCCMD clients are optional and not freeware Most CS121 are equipped today with a single RCCMD standard license some UPS makers add more licenses other do not deliver any license at all with a CS121 Contact your UPS maker and ask for the license regulations for RCCMD in conjunction with your CS121 License regulations Please note that in order to use these functions legally the corresponding RCCMD client program is installed and started from the UPS Management Software CD The RCCMD license code can only be used once per installation If more computers need to be added to the shutdown process additional RCCMD client licenses are required To send shutdown signals to computers in case of a powerfail event you have to install and configure the RCCMD client at the computers you want to shutdown and make some configurations at the adapter s event settings 2 Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download
25. interface 12 Route command and routing table 13 HTTP logon 13 HTTP Basic network settings 14 HTTP UPS Model amp System Settings for SITEMANAGER II v3 15 HTTP menu with SiteManager II v3 configuration 15 HTTP configuration Analog Inputs 16 HTTP configuration Digital Inputs 16 HTTP configuration Outlets 17 Alarm matrix Marker configuration 17 Alarm Matrix Switching of relay outputs 18 HTTP Status Display of the Outlets 18 HTTP menu for status displays 19 Status display with temperature and humidity sensor as well as digital Inputs and Outlets 20 Configuration of the thresholds of the analog Inputs 21 Configuration of the threshold events of the analog Inputs 21 Configuration of the threshold events for SM_analogue 1 22 SiteManager II v3 gChart 23 HTTP Event Configuration with tool tip 23 HTTP Event Editor 24 HTTP Job Editor Continuous event job 25 HTTP Job Editor Send SMS with GSM modem 25 Siemens GSM TMA T35i modem 26 HTTP Sytem amp Network Status 26 HTTP Job Editor Email Job 27 31 Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download
26. m Shutdown Time in the menu UPS model and system is reached This means there are yet the configured minutes left until the battery s capacity is expected to be finished as calculated by the adapter This event should only be used to proceed all operations concerning your forced shutdown scenarios Further operations are usually configured on the event Powerfail ay Note This EVENT is the final task a CS121 can initiate before the UPS switches off DO NOT use this event for triggering shutdowns via RCCMD etc because the remaining time in this status is not secure We strongly recommend to use the event Powerfail and configure the RCCMD shutdown calls with a UPS remaining time this is the best way to send RCCMD shutdowns to several IP addresses in a certain logic or sequence e Battery low The event Battery low will be released from the UPS when the battery charge has reached a critical State e UPSMAN started Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download The event UPSMAN started is periodically released in normal operating mode You can use this event to configure jobs which should be executed as long as the adapter is working in normal mode G Note Same UPS models allow you
27. me 1 Switch On Outlet 1 5 Switchom outlets 2 Outlet 2 6 Outlet 6 J 4 Switch On Outlet 3 7 oG Outlet 4 oi Switch On Outlet 4 8 setbymarker Outlets Figure 25 HTTP Status Display of the Outlets 4 3 Status display The Sitemanager Il v3 incorporates different pages for monitoring Choose in the menu Network amp Security which status page is the HTTP default page and will be displayed on start up of every HTTP connection 18 Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download 4 3 1 Input Output status Monitor the state of the devices connected at the SiteManager II v3 inputs outputs through the menu SiteManager II v3 Status default setting for HTTP default page C 121 Status System amp Network Status Configuration UPS Model amp System Figure 26 HTTP menu for status displays The status display gives you an overview of the output input status and of the actual sensor measurements as well as its thresholds for the alarm Additionally you have the possibility to acknowledge alarms Button Ack as shown in the figure above Note If an alarm is present at an output you can not switch the output because the priority of the alarm is higher Turn off the alarm if you w
28. n answer please observe that the routing table contains a route for the SiteManager II v3 IP address The basic settings are now completed and the SITEMANAGER II v3 is integrated into the network environment 14 Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download Configuration Connected devices System amp Network Status Sitemanager llv3 Status Network amp Security LED Display Scheduled Actions SNMP EMail UPS Model amp System Settings UPS Model Power VA Load VA SiteManager 1v3 Bo Bo io Ee 500 S00 10 5 2400 serial B Hold Time min Recharge Time hi Baud Rate Cable Type Exchange COM Ports Custom Values Custom Text Custom Text2 Custom Texts Timeserver Events Alarms Sitemanager lla Save Configuration Figure 18 HTTP UPS Model amp System Settings for SITEMANAGER II v3 Select the UPS Model SiteManager II v3 into the UPS Model amp System Settings UPS Mode Network amp Security LED Display Scheduled Actions SNMP EMail Timeserver Events Alarms Save Configuration mE Figure 19 HTTP menu with SiteManager II v3 configuration Use this menu to configure the devices at the input and output sockets 4 1 1
29. nd Analog Input sockets of the SiteManager II v3_Rev B from SN SMG05 00411 or higher have changed The lower sockets X1 deliver the power supply of 15 VDC and the Digitalinput sockets are on the upper 8 right ports of X2 The Analoginputs are on the upper 8 left Ports of X2 Fig Digital Analog Inputs SiteManager II v3 Please notice the Fig Schematic Digital Inouts and Schematic Analog Inouts when you connect your devices Function X1 15V X1 X2 A01 X2 A02 X2 A03 X2 A04 X2 A05 X2 A06 X2 A07 SITEMANGER II Digital Inputs digital inputs digital inputs Fig Schematic Digital Inputs Fig Schematic Analog Inputs 11 Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download 2 1 4 Switchable relay outputs Relays Output R1 R2 R3 R4 R5 R6 Figure 12 Switchable relay outputs The SITEMANAGER II v3 contains 8 switchable relay outputs to operate all kind of current consuming devices up to 4A Please see the following circuit examples SITEMANAGER II Relay output Relay output Relay output i Figure 13 Relay outputs 2 2 Status LED s The status of each Input and Output connector is shown by the LED at the SITEMANGER II v3 front display whereas a green lit LED indicates that the output input i
30. net Server On Network Speed AUTO HTTP Server On IP Address 192 168 222 186 Upsmon Server On Subnet Mask 255 255 255 0 Use RCCMD2 Traps Yes Default Gateway 192 168 222 100 SNMP Server On DNS Server 192 168 222 100 Use SNMP Coldboot Trap No EMail Server not configured Use SNMP Authentication Trap No Time Server 129 6 15 29 Modbus Server On Figure 37 HTTP sytem amp Network Status 4 4 1 3 concerning the Sitemanager II v3 Inputs Outputs Each connected device at the input or output socket has its own event which allows to release specific actions in dependency of the status of the device Therefore the following events are supported e Alarm Analog Input 1 8 Will be released if the configured alarm thresholds see section 4 1 1 are exceeded e PreAlarm Analog Input 1 8 Will be released if the configured prealarm thresholds see section 4 1 1 are exceeded e Alarm Digital Input 1 8 Will be released if the contact state indicates the alarm state Opposite of NC contact see section 4 1 2 e Alarm Marker 1 8 Will be released if the configured Marker see section 4 2 is set e Output 1 8 on Will be released if the output relay is switched see section 4 1 3 e Digital Input 1 8 off Will be released while the digital input is set as active and OFF see section 4 1 2 This event can be used to release a continuous periodic action e Digital Output 1 8 off Will be released while the relay output is s
31. ow the instructions on the GENEREX download page 22 Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download SiteManager Chart M Cabinet temperature 1 Cabinet temperature 1 ee v Cabinet humidity Cabinet humidity W Cabinet temperature 2 Cabinet temperature 2 gt Analog Input 4 Analog Input 5 Analog Input 6 Mains voltage Analog Input 8 Toggle Grid Toggle Legend Show Values 21 02 2007 21 02 2007 21 02 2007 21 02 2007 21 02 2007 21 02 2007 21 02 2007 10 20 00 10 33 20 10 46 40 11 00 00 11 13 20 17 26 40 17 40 00 GChart Navigation Zoom In Press Ctrl key while marking the zoom area with the let mouse button Pan Scroll Press Shift key while moving the mouse with left button pressed inside the diagram if zoomed Zoom Out Press right mouse button inside the diagram Show Tooltips Press left mouse button inside the diagram Move Legend Press left mouse button inside the legend Figure 31 SiteManager Il v3 gChart 4 4 Event configuration The Event Alarm configuration is based on a combination of events and actions resp Jobs At the SiteManager Il v3 there are various events defined e g events concerning the attached devices like Alarm Analog Input 1 Alarm Digital In
32. ozilla are supported to the address http 10 10 10 10 to reach the SiteManager II v3 Webinterface First of all the HTTP interface requires a logon whereas you use the username admin and the default password cs121 snmp Senere SiteManager II Status Version 2 03 Digital Outputs Digital Inputs Analog Alarms SiteMan ager CS 121 Status I SE I RC TS Power System amp Network Status Verbindung herstellen mit 192 168 222 176 Sitemanager Ilv3 Status i Configuration UPS Model amp System 7 8 Der Server 192 168 222 176 an admin erfordert einen Analog Input Analog Input Analog Input Benutzernamen und ein Kennwort LED Display Scheduled Actions SNMP EMail Timeserver Events Alarms Sitemanager Iliv3 Save Configuration 255 Warnung Dieser Server fordert das Senden von Benutzernamen und Kennwort auf unsichere Art an Basisauthentifizierung ohne eine sichere Verbindung 204 Benutzername admin 153 Kennwort Logfiles AlarmLog Web Links CS121 Online Manual Firmware Update F Kennwort speichern Figure 16 HTTP logon 13 Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download Call the menue Network amp Security Make the settings for Local Address Gat
33. p unset you can specify the actions to be executed when an marker will be set unset Therefore you have two possibilities The first is to handle the actions through the event configuration described later on in section 4 4 Event configuration This is possible because each marker has its own event Alarm Marker x which can be configured through the event configuration The second possibility is to switch an relay output in dependency of the statue of one or several markers Therefore you have the output matrix figured as below In this example is configured that Output 6 is to be switched on when Marker 1 or Marker 2 is set or the opposite way around in case Output Inverted is enabled Using the Alarm Matrix offers you numerous possibilities to switch Outputs in dependency of input alarms at Logic Marker a s e Output 1 A And GB E ew aoe hulle Output 2 E And rem e OEH o ORAT Output 3 E And m fe ae oe M Output 4 E And rem E nmen non HEAT Output 5 E And Em e Omio 0 PST Output 6 E Or va OET O mN EEr Output 7 E And e n ape oe lhe hue Output 8 E And E a a Ml M M le i Apply Disable Outputs Figure 24 Alarm Matrix Switching of relay outputs If Outputs were linked in dependency of input alarms into the Alarm Matrix the buttons for the manually switching are no longer present Instead the advice set by marker is displayed Outlets Status Switch Name Status Switch Na
34. port is usually 6003 At the right side you can specifiy when the shutdown signal is to be released e g do after 300 seconds D Note For security reasons we recommend to make the same RCCMD shutdown entries at Powerfail for the Event Battery low but here without any delays to avoid that the server crashes because of low battery alarm 28 Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download Appendix A SITEMANAGER II v3 technical data Power Supply 15VDC stabilized 1A then about 500mA are left for supply of sensors Max permitted current per output 4 A with ohmic load cos phi 1 Dimensions 430 mm x 156 mm x 44 mm BxTxH with mounting brackets 19 1 HE Operating temperature 0 40 C Rel air humidity 0 95 not dewed Degree of protection IP 20 Cable diameters for outputs 0 2mm 2 5mm B Pin layout for Input sockets Sensor Input 1 Pin 1 12 VDC Pin 2 Analog Channel 1 0 10V Pin 3 Analog Channel 2 0 10V Pin 4 GROUND Pin 5 SM_Il_DIG Sensor1 Input Pin 6 SM_Il_DIG Sensor2 Input Sensor Input 2 Pin 1 12 VDC Pin 2 Analog Channel 3 0 10V Pin 3 Analog Channel 4 0 10V Pin 4 GROUND Pin 5 SM_Il_DIG Sensor1 Input Pin 6 SM_Il_DIG Sensor2 Input Sensor Input 3 Pin 1 12 VDC
35. put 1 etc and also events concerning a connected UPS like Powerfail UPS Battery bad Battery low etc The SiteManager II v3 allows you to release one or more actions on each event An action can be e g to write a logfile entry in the alarm logfile as default all events do perform an logfile event to send an eMail or to perform an RCCMD Command e g shutdown signals to several RCCMD Clients To configure events and actions open the menu Events Alarms The menu Event Configuration shows you an overview about the events and the number of configured actions Event Configuration Event Overview RCCMD RCCMD RCCMD UPS RCCMD Soot LeU LE Shutdown Message Execute Shutdown so La Trap roar 0 0 1 1 1 0 0 0 1 Pow Powerfail 4 Jobs System qi RCCMD Msg 192 168 202 147 UPSMAN 2 RCCMD SD 192 168 202 147 3 RCCMD Exe 192 168 202 147 UPS coni4 RCCMD Trap Powerfail on SERVER UPS can power system for 4UTONOMTIME min Aa m m M m m m m Figure 32 HTTP Event Configuration with tool tip Choose the event you wish to configure to enter the event editor a UNa 23 Copyright of the European Union is effective Copyright EU c 2010 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download Event Editor Event PreAlarm Analog Input 1 Low Event Jobs for
36. r II v3 Disconnect all cables from the SiteManager II v3 Dismount the device screw off the 4 lateral screws and take off the housing cover Get the jumpers in their desired position see fig 8 9 Delivery state analog inputs 0 10V Both jumpers of the analog inputs 1 8 channel 1 8 are set at PIN 1 2 see fig 8 In this positions of the jumpers the following sensors are permitted for the connection at the analog inputs and should be selected as sensor types into the SiteManager II v3 configuration only e Custom 0 10V e SM _ILT e SMIIT H e SM II T_ Plus e SM II VMC e SM IIL CMC Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download M R ckseite Anschl sse M Channel8 Channel Channel 6 Le 2 N X g uh tu i ie 7 pi Channel3 i Channel2 j Channeli NY Frontseite Figure 8 Jumper positions of the delivery state Positions of the jumpers of the analog inputs 0 20mA or rather 4 20mA Both jumpers of the analog inputs 1 8 channel 1 8 are set at PIN 2 3 see fig 9 In this positions of the jumpers the following sensors are permitted for the connection at the analog inputs and should be selected as sensor types into the SiteManager II v3 configuration only e Custom 0 20mA e Custom 4
37. s 99 Alarm Digital Input 2 off 1 0 0 0 0 Device Status 100 Alarm Digital Input 3 off E 1 0 D D 0 rule ragerta ep hor 101 Alarm Digital Input 4 off 1 0 0 0 0 pain aes 102 Output 4 on 1 0 0 0 0 SensorMan 2 Status 103 Oufput2 on 1 0 9 o H 104 Output3 on 1 0 0 0 0 me A A LD 105 QOutput4 on 1 0 0 D 0 UPS Model amp System 106 Output off 4 fil o 0 0 Network amp Security 107 Output 2 off 1 0 o o D Ewes 408 Output 3 off F 1 0 D D 0 RAS Configuration Scheduled Actions Se L SNMP 110 Alarm Marker 1 1 it 0 it 0 EMail 1411 Alarm Marker 2 E 1 i 0 Timeserver 112 Alarm Marker 3 1 0 0 0 D COM amp AUX 113 Alarm Marker 4 El 1 0 0 0 0 SsensorManager 114 Alarm Marker 5 El 1 0 0 D 0 Events Alarms 415 Alarm Marker 6 E 1 0 0 D 0 ee m 416 Alarm Marker 7 A 1 0 0 0 o 417 Alarm Marker 8 El d 0 ii 0 0 118 Alarm Marker 1 off 1 0 0 0 119 Alarm Marker 2 off El d 0 0 0 120 Alarm Marker 3 off 1 0 0 0 0 E 0 0 0 0 El 0 0 0 0 0 D 0 0 0 D 0 o 0 0 Oo 0 0 0 0 0 0 i 0 lt lt Events 68 97 Configure threshold events Figure 30 Configuration of the threshold events for SM_analogue 1 4 3 2 gChart gChart offers to monitore numerousness measurement values in a graphical visualisation through a chart gChart is a GENEREX plug in for the MS Internet Explorer available as free download from the GENEREX web side It is realized as activeX component and must be installed on the client side How to install the chart please foll
38. s active and a red LED is shown in the case of a alarm the LED is flashing while the alarm is not acknowledged Digital Outputs Digital Inputs Analog Alarms SiteManager 123 4 1 2 3 4 1 2 3 4 reer cre GOC Power CC 5 6 F 8 5b 6 fF 5 6 7 6 Figure 14 Status LED s at HTTP interface The actual status is also shown at the SITEMANAGER Il v3 web interface see figure above to monitor the devices on remote Here 4 status are differentiated Gray unlit Input Output is not active Green Input Output is active Yellow Alarm acknowledged 12 Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download 3 Getting started Basic settings Firstly the startup of the SiteManager II v3 requires some basic settings by which the SiteManger II v3 unit will be integrated into the network environment Set DIP switch 1 and 2 to position OFF after having connected the LAN port with an RJ45 cable to the network and where required having connected the UPS at COM1 with the original vendors cable This sets the SiteManager II v3 to the configuration mode and enables the default IP adress 10 10 10 10 Plug in the power supply then to initiate the boot process A running boot procedure is indicated with gre
39. witched off This event can be used to release a continuous periodic action Copyright of the European Union is effective Copyright EU c 2011 GENEREX GmbH Hamburg Germany All rights reserved TEL 49 40 22692910 EMAIL info generex de WEB www generex de This and all other product datasheets are available for download 4 4 2 Email Job Powerfail Job 3 Function Send an E ail When Q Immediately once Receiver someone somewhere com C Always Text klarm MODEL FAUTONOMTIME min left 2 Every 0 seconds Use text as Yes C after fo seconds subject C After fo seconds amp repeat C After fo seconds on battery C At lo seconds remaining time Apply Cancel Figure 38 HTTP Job Editor Email Job To configure an Email job follow the entries in the figure above Note It is condition before you configure an Email job that you have made the Email settings in the menu Email Please observe that the entries are valid before testing Apply your settings and test the Email job in the Event Editor to ensure Email will be sent 4 4 3 RCCMD Perform shutdown signals to network computers RCCMD Remote Console Command is the world s most successful shutdown client for heterogeneous networks and is the most secure way to establish a UPS multiple server shutdown sequence today RCCMD clients are listening to an RCCMD server which is usually an UPSMAN software CS121 or any third party UPS mana

UPS WEB/SNMP MANAGER

Contents

Download Pdf Manuals

Related Search

Related Contents