FPM-3171 User Manual
Contents
1. FPM 3171 17 SXGA Industrial Monitor with Resistive Touchscreen Direct VGA and DVI Ports User Manual Copyright This document is copyrighted by Advantech Co Ltd 2005 All rights are reserved Advantech Co Ltd reserves the right to make improvements to the products described in this manual at any time Specifications are thus subject to change without notice No part of this manual may be reproduced copied translated or transmit ted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable However Advantech Co Ltd assumes no responsibility for its use nor for any infringements upon the rights of third parties which may result from its use All brand and product names mentioned herein are trademarks or regis tered trademarks of their respective holders This Manual Covers the Following Models FPM 3171G X0AE 17 SXGA WT Ind Monitor with VGA DVI FPM 3171G R3AE 17 SVGA WT Ind Monitor w Resistive TS Combo Part No 4th Edition Printed in Taiwan August 2012 FPM 3171 User Manual ii Product Warranty 2 years Advantech warrants to you the original purchaser that each of its prod ucts will be free from defects in materials and workmanship for two years from the date of purchase This warranty does not apply to any products which have been repaired or altered by persons other than repair pers2. 7 Chapter 2 Chapter 2 Mounting 2 1 Mounting the Monitor The FPM 3171 Series can be placed as you require The versatility of the FPM 3171 mounts enable it to be mounted on your desk or anywhere else 2 1 1 Wall Mounting With wall brackets the FPM 3171 can be mounted directly to a wall If you need to install the FPM 3171 in different ways release the mount ing brackets by detaching the four screws on the rear side Figure 2 1 Wall Mounting FPM 3171 User Manual 8 2 1 2 Panel Mounting If you need to install the FPM 3171 series on a panel mount please release the mounting brackets by detaching four screws on rear side and fix them on up and bottom side by screws Figure 2 2 Panel Mounting Cutout Dimensions 447 5x329 5 9 Chapter 2 2 1 3 Rack Mounting FPM 3171G series products could be directly mount to the industrial standard 19 rack There are four screw holes on each side of the panel Figure 2 3 Rack Mounting FPM 3171 User Manual 10 2 2 Desktop Swing ARM Mounting The FPM 3171 Series can be mounted in other ways You can place the desktop stand for desktop use or attach it on a swing arm bracket 2 2 1 Desktop Stand The desktop stand brackets are attached to the rear of FPM 3171 Figure 2 4 Desktop Stand for the FPM 3171 Il Chapter 2 2 2 2 Swing ARM Detach the mounting brackets on the rear side then attach the FPM 3171 series onto the Swing ARM mount 75mm or 100mm square bracket
3. Figure 2 5 Swing ARM for the FPM 3171 FPM 3171 User Manual 12 Appendix Touchscreen Driver Installation 13 Appendix A Appendix A Touchscreen Installation A 1 Introduction The FPM 3171 Series optional touchscreens uses 5 wire resistive tech nology They provide more accurate sensing capacity than other technolo gies The touchscreen is specially designed for tough industrial environments and has been approved to FCC Class A Note RS 232 amp USB touchscreen interface does not allow connection to the system at the same time It can be changed by switch A 1 1 Resistive Type Supply Voltage and Current e 5 Vdc nominal 4 50 Vpc to 5 25 Vpc Self powered only e 50 mA standby typical at 5 Vdc during touch 160 mA average 240 mA peak e Average power dissipation is 0 5 W typical Supply must be capable of sourcing 400 mA minimum Total noise and ripple requirement must be less than 100 mV p p for frequencies below 1 MHz and less than 50 mV p p for frequen cies above 1 MHz Serial Interface s FIA 232E Serial RS 232 DCE configuration 8 Data Bits 1 Stop Bit No Parity Full Duplex e Hardware handshaking RTS CTS e DSR is pulled HIGH gt 3V by the touch screen control board when connected and powered DTR can be asserted by the host to inter rupt the flow of data from the controller Note that if the applica tion does not monitor CTS then an interval of approximately 5 second
4. Setup Complete screen appears you may choose to run calibration the Elo Video Align ment program Elo VA immediately or wait until later If you choose not to run this program now you can run it from the Elo Control Panel application When EloVA runs for the first time it will attempt to calibrate all controllers and or serial ports that were installed Press the Esc key on the keyboard to terminate or skip calibration for any monitor or allow the program to time out as indicated by the progress bar reaching maximum The program will continue until all controllers and or ports have been calibrated Multiple monitors serial and USB controllers l Run the self extracting zip file to unzip the files using the Run EloSetup option EloSetup will launch Check both the Install Serial Touchscreen Drivers and Install USB Touchscreen Drivers boxes Review and accept the License Agreement The program will appear to proceed as a single multiple serial con troller installation but USB files will also install The driver files will install When the Setup Complete screen appears you may choose to run calibration the Elo Video Align ment program Elo VA immediately or wait until later If you choose not to run this program now you can run it from the Elo Control Panel application When EloVA runs for the first time it will attempt to calibrate all controllers and or serial ports that were installed Press the E
5. StandBy Off Green Blinking No Signals Orange FPM 3171 User Manual 28 C 2 OSD Key Functions Each selected value is stored into LCD memory after SEL signal input or time out The stored values are not affected if the power is turned off But the selected value is not available in case a selected mode is changed before time out or power is turned off before time out TIME OUT 5 6 seconds Can be set in OSD Manager The default definition of input keys is shown as following C 2 1 Menu Start Generate Main Menu Press MENU Button in OSD function key e Main Menu oc 49KHz S9Hz 1024x768 Picture Geometry Color OSD Manager Input Select All Reset Exit Exit Sel Select G1I9OEG 12 e Available Key Functions i Select to exit menu or wait for pamm N A amp time out F o so 29 Appendix C C 2 2 Picture Select by Left and Right Button press Menu Button for selection Confir mation e Main Menu Picture Geometry Color OSD Manager Input Select All Reset s Sub Menu Picture Meme mr yi Memory2 User Color li iii Memory Brightness DIM Brightness Contrast i WW FPM 3171 User Manual 30 e Available Key Functions Power off the LCD monitor Decrease the gauge value of the selected option Return to last menu Selected to confir
6. the I O from this unit DVI Port DVI D Connected with a standard DVI connector thru I O port of this unit Only supports digital signals Touchscreen Connector DB 9 This connector will be present only if a touchscreen is installed It must be connected to the RS 232 port of the PC The touchscreen cable is included with all orders which include the RS 232 touchscreen option Touchscreen Connector USB This connector will be present only if a touchscreen is installed It must be connected to the USB port of the PC The touchscreen cable is included with all orders which include the USB touchscreen option Note RS 232 amp USB touchscreen interface does not allow connection into the system at the same time but it can be changed via switch DC 12V or DC 24V Power In This connector connects to the DC 12V 24V Switching Power Supply J Chapter 1 1 6 Dimensions Lol ANI NOL oooooonoovononoonoooonnooonoun oooooonoooononnonoooonnoonnoon oooononoon onoooonoon T oooononooovonbodovoononoovonon oooononoooonpodosgaeonoo onnon Dooononoonoopojonoononoo nonon nann L L Banan oopooonoon oopooonoon oopooonoon oopooononn Figure 1 1 FPM 3171G Dimensions FPM 3171 User Manual CHAPTER Mounting
7. www advantech com where you can find the latest information about the product 2 Contact your distributor sales representative or Advantech s customer service center for technical support if you need additional assistance Please have the following information ready before you call Product name and serial number e Description of your peripheral attachments e Description of your software operating system version application software etc e A complete description of the problem e The exact wording of any error messages FPM 3171 User Manual iv Safety Instructions l 2 3 Read these safety instructions carefully Keep this User s Manual for later reference Disconnect this equipment from any AC outlet before cleaning Use a damp cloth Do not use liquid or spray detergents for clean ing For plug in equipment the power outlet socket must be located near the equipment and must be easily accessible Keep this equipment away from humidity Put this equipment on a reliable surface during installation Drop ping it or letting it fall may cause damage The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before con necting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings
8. 280 1024 Yes Yes Yes Note 1 Even if the preset timing is entered some adjustment of func tions such as Horizontal period CLK delay and display position are required The adjusted values are memorized in every preset number Note 2 This module recognizes the synchronous signals with near preset timing of the frequency of the HS and Vsync even in the case that the signals other than the preset timing that were entered Note 3 Because adjustments may not fit such as differing magnifying ratios or in the case that you use it except for the display timing that was preset FPM 3171 User Manual 26 C Appendix OSD Operation Keypad 27 Appendix C Appendix C OSD Operation Keypad C 1 OSD Board Overview C 1 1 OSD Button Description Buttons Descriptions Source Changes input video source Menu Sel Activate the OSD menu Enter confirm the selected option Left Activate volume control Decrease Move the selector to the previous option Arrow Decrease the gauge value of the selected option Brightness can be decreased by left button Right Activate the volume control Increase Move the selector to the next option Arrow Increase the gauge value of selected option Brightness can be increased using the right button Auto Exit Automatically adjust the closck phase H position and V position Exit menu Power Turn the monitor ON and OFF C 1 2 LED Function On Green
9. 3 Appendix C e Available Key Functions Power off the LCD Decrease the gauge ly monitor value of the selected option Selected to confirm Return to last menu Increase the gauge N A value of the Source selected option C 2 6 Input Select e Main Menu abla Picture Geometry Color OSD Manager Input Select All Reset Rr FPM 3171 User Manual 34 e Available Key Functions Power off the LCD Decrease the gauge L 1 monitor value of the selected option Selected to confirm Return to last menu Increase the gauge N A value of the ce selected option 35 Appendix C FPM 3171 User Manual 36 Appendix FPM 3171S Dimensions 37 Appendix D Appendix D FPM 3171S Dimensions Look NOISNAWIG ononooooooonooononnooooooonoonon0n000000 Doooooooo000n000000000000000000000000000 D00D0DODODODDD0000000D000000000000000000 a ne ouseuoooon _anaonnanan FPM 3171 User Manual 38
10. CHAPTER Introduction 1 Chapter 1 Chapter 1 Introduction 1 1 Introduction Advantech s FPM 3171 Series is a 17 color TFT LCD flat panel monitor built specifically for industrial applications With the optional touch screen the FPM 3171 Series is an excellent and user friendly system control interface In addition to its usual application as an LCD panel monitor FPM 3171 comes standard with direct VGA and DVI control signal inputs making it compatible with Industrial PCs and Workstations Its OSD Onscreen Display function allows you to adjust the display factors and turn the backlight on and off for the front view functions which become critical as more and more industrial HMI users become aware of the benefits of flat panel monitors FPM 3171G models are equipped with Stainless Steel chassis and NEMA4 IP65 compliant Aluminum front panel Therefore FPM 3171S is made of Stainless Steel chassis and NEMA4X IP65 com pliant 316L Stainless Steel front panel The FPM 3171 Series has an optional resistive touchscreen With a resis tive touchscreen the monitor can be immediately transformed into a remote control system FPM 3171 User Manual 2 1 2 Specifications General Construction Heavy duty Aluminum and Stainless Steel Front panel Aluminum NEMA4 IP65 Compliant Control OSD On Screen Display control pad on front side Mounting Panel wall desktop VESA or rack with kit Dimensions W x H x D 482mm x 354 8mm x 63 9m
11. a SW601379_TETouch_5 2 0 exe Single monitor serial controller 1 Run the self extracting zip file to unzip the files using the Run EloSetup option FPM 3171 User Manual 16 2 EloSetup will launch Check the Install Serial Touchscreen Driv ers box Elo Touchscreen Setup Welcome to Elo Touchscreen Setup This program will install the Elo USB and Serial touchscreen drivers on your computer It is strongly recomended that you exit all Windows programs before tunning this Setup program Install USB Touchscreen Drivers Back Cancel 3 Review and accept the License Agreement 4 Check Auto detect Elo devices if your touchmonitor serial cable is connected to the computer and the serial cable supports hardware handshaking If you connect the serial cable later do not check the auto detect box Go to the next screen Elo Touchscreen Setup Select the COM ports to use with Elo serial touchscreens Check the Auto detection box if you want Setup to auto detect COM ports currently connected to Elo devices During Auto detection Setup will send data to each port which may temporarily interfere with some types of serial devices Click Next to continue lt Back Cancel 17 Appendix A 5 A list ofall the serial ports that the system detected is shown If you checked the auto detect box in the previous screen and your touch monitor serial cable is attached to the computer the COM port tha
12. anual 22 e Change Serial Port To change Serial port click on the Change option from the Add Remove programs in the Control Panel Elo entry R Add or Remove Programs blo Elo XP Universal Driver 23 Appendix A e Adding Additional USB Controllers If there are Elo USB devices already installed plug the USB cable from the touchmonitor into the computer and run EloVA to calibrate the touch monitors If there are no Elo USB devices attached to the system click on the Change option from the Add Remove programs in the Control Panel Elo entry Elo Touchscreen Configuration Welcome to Elo Touchscreen configuration This application allows you to select serial ports for Elo Serial touchscreens and install Elo USB touchscreen drivers on your computer It is strongly recommended that you exit all Windows programs before running this configuration program T Configure Serial Touchscreens Ba Cancel FPM 3171 User Manual 24 Appendix Setting Serial Data for Expansion 25 Appendix B Appendix B Setting Serial Data for Expansion B 1 Supported Input Timing Modes The different frequencies below are already programmed in this module and the synchronous signal inputs are automatically recognized Table B 1 Supported Input Formats Vertical Frequencies Resolution 56 Hz 60 Hz 70 Hz 72 Hz 75 Hz 640 x 480 Yes Yes Yes 720 x 400 Yes 800 x 600 Yes Yes Yes Yes 1024 x 768 Yes Yes Yes 1
13. cifi GRIGS e a ces enced bance baht eee iste Me Mee 3 LED Specifications lt i chee eesti Sch n ce 42 yavs Power Consumption CONECO Dimension Skace E ea Figure 1 1 FPM 3171G Dimensions I STE ST TE Mounting the Monitor sss esse ee eee 8 2 1 1 Wall Mounting sse sees eee eee e 8 Figure 2 1 Wall Mounting 2 1 2 Panel Mounting Figure 2 2 Panel Mounting 2 1 3 Rack Mounting sss eee Figure 2 3 Rack Mounting Desktop Swing ARM Mounting sees sees eee eee 22 1 Desktop Stand ii ccesuiesinecivinan nian e Figure 2 4 Desktop Stand for the FPM 3171 22 2 Swings ARM oee Figure 2 5 Swing ARM for the FPM 3171 ee Touchscreen Installation sss sss sss vesse 14 Tntr duc STE 14 A L 1 Resistive Type cccccecssssssssssesceecesceeceeceseeseesecneeneens 14 Resistive Touchscreen Driver Installation sss esse 15 A 2 1 Hardware A 2 2 Software Setting Serial Data for Expansion 26 Supported Input Timing Modes sss sese Table B 1 Supported Input Formats OSD Operation Keypad cccssssssseeeee 28 OSD Board Overview sese ss see eseeee rees ereenn nnn C 1 1 OSD Button Description C 1 2 LED Function OSD Key Functions C 2 1 Menu Startede cnca a C 2 2 Picture ls C253 GEOM iar ai R a A ERE AS CZA a Colo arrun eser a vii Table of Contents C 2 5 OSD Mata ger T 33 C 2 6 Input Select TTT 34 Appendix D FPM 3171S Dimensions sss sss vesse sss vesse dd FPM 3171 User Manual viii
14. e date is not eligible for war ranty service 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer iii FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interfer ence when the equipment is operated in a residential environment This equipment generates uses and can radiate radio frequency energy If not installed and used in accordance with this user s manual it may cause harmful interference to radio communications Note that even when this equipment is installed and used in accordance with this user s manual there is still no guarantee that interference will not occur If this equip ment is believed to be causing harmful interference to radio or television reception this can be determined by turning the equipment on and off If the interference is occurring the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment to a power outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Additional Information and Assistance 1 Visit the Advantech web site at
15. m i EX B D Increase the gauge N A value of the selected option C 2 3 Geometry e Main Menu IUT Picture Geometry Color OSD Manager Input Select All Reset s Sub Menu OoSition Position 31 Appendix C e Available Key Functions Decrease the gauge value of the selected option F Power off the LCD 0 monitor us Return to last menu Selected to confirm N A r Increase the gauge gt value of the l selected option C 2 4 Color e Main Menu Picture Geometry Coler OSD Manager Input Select All Reset GISOEGO 1 S Sub Menu Col CAAT User Color FPM 3171 User Manual 32 e Available Key Functions Power off the LCD monitor Decrease the gauge value of the selected option Return to last menu Selected to confirm r Increase the gauge N A gt value of the selected option C 2 5 OSD Manager e Main Menu Picture Geometry Color OS0 Manager Input Select All Reset s Sub Menu T OSD Manager OSD H Pos OSD V Pos N ITR Timer Language UDIT 3
16. m 18 98 x 13 97 x 2 54 Weight 9 25 kg 20 39 Ibs Touchscreen Optional Type 5 wire analog resistive Resolution 4096 x 4096 for resistive model Light transmission 80 5 Operating Pressure 30 45 gram for stylus contact bounce lt 10 ms Controller RS 232 and USB Power Consumption 5 V 100 mA OS Support Windows XP Vista 7 XPe CE and Linux Life Span Resistive 35 million activations typical at single point with a 5 8 diameter silicone finger at 350g load at 2 touches per sec Capacitive 225 million activations typical at a single point with a 5 8 diameter silicone finger at 350g load at 2 touches per sec 3 Chapter 1 1 3 LCD Specifications s Display type SXGA TFT LCD Display size 17 Max colors Full color 16 2 million Max resolution 1280 x 1024 Dot pitch 0 264 x 0 264 mm Viewing Angle 170 H 160 V Luminance 350 cd m Storage Temperature 30 80 C 22 176 F Operating Temperature 20 60 C 4 140 F Backlight Lifetime 50 000 hrs Contrast Ratio 1000 1 1 4 Power Consumption e Max Output Power 35W 20 e AC Input Voltage 100 240VAC s Output Voltage 12V 4 7A s Safety Standards BSMI CE FCC CCC UL FPM 3171 User Manual 4 1 5 Connectors The following connectors are situated on the left hand side of the FPM 3171 Series VGA Port DB 15 This DB 15 connector can be connected to the system via the external 15 pin DB 15 connector thru
17. on are Automatic detection of the controllers on serial ports during setup is not possible Controller information will not be registered in the Property Page of the Control Panel 15 Appendix A USB USB controllers require no configuration prior to installation Elo s USB controllers are Human Interface Device HID compliant The Windows XP operating systems have native HID drivers that pro vide low level support for Elo touchscreen controllers An Elo touch monitor with a USB touchscreen controller installed will provide the following limited operation with these native HID drivers Operation of the controller will be limited without the installation of the software discussed in the next section The mouse cursor will move on the display in response to touch The direction of motion on the display will depend on the orientation of the touchscreen and the defaults programmed into the controller and the driver No beep will be heard when the screen is touched No Control Panel application is available to configure the operation of the driver A 2 2 Software There are many options to consider when installing the driver files This section will explain the most common ways that the driver is installed Consult Elo Applications Engineering for situations not covered in this section Setup from Windows Desktop For WinXP OS please execute CDROM TouchScreen DRV ELO Touch Driver Windows Drivers Win dows XP 7 Vist
18. on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage Never pour any liquid into an opening This may cause fire or elec trical shock Never open the equipment For safety reasons the equipment should be opened only by qualified service personnel If one of the following situations arises get the equipment checked by service personnel a The power cord or plug is damaged b Liquid has penetrated into the equipment c The equipment has been exposed to moisture d The equipment does not work well or you cannot get it to work according to the user s manual e The equipment has been dropped and damaged f The equipment has obvious signs of breakage 15 DONOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW 30 80 C 22 176 F THIS MAY DAMAGE THE EQUIPMENT The sound pressure level at the operator s position according to IEC 704 1 1982 is no more than 70dB A DISCLAIMER This set of instructions is given according to IEC 704 1 Advantech disclaims all responsibility for the accuracy of any state ments contained herein FPM 3171 User Manual vi Chapter 1 1 1 1 2 1 3 1 4 1 5 1 6 Chapter 2 2 Appendix A Al A 2 Appendix B B 1 Appendix C C 1 C 2 Contents Introduction sss ssssssssssssssss sss ssss sees 2 Introd ctiot iie a a ii 2 Spe
19. onnel authorized by Advantech or which have been subject to misuse abuse accident or improper instal lation Advantech assumes no liability under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous test ing most of our customers never need to use our repair service If an Advantech product is defective it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem occurs 2 Call your dealer and describe the problem Please have your man ual product and any helpful information readily available 3 Ifyour product is diagnosed as defective obtain an RMA return merchandize authorization number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchas
20. roller 1 Run the self extracting zip file to unzip the files using the Run EloSetup option EloSetup will launch Check the Install USB Touchscreen Driv ers box Review and accept the License Agreement The driver files will install When the Setup Complete screen appears you may choose to run calibration the Elo Video Align ment program Elo VA immediately or wait until later If you choose not to run this program now you can run it from the Elo Control Panel application Multiple monitors serial controllers 1 Follow the general procedure for Single monitor serial controller installation above auto detecting or selecting all the serial ports that you will use The driver files will install When the Setup Complete screen appears you may choose to run calibration the Elo Video Align ment program EloVA immediately or wait until later If you choose not to run this program now you can run it from the Elo Control Panel application When EloVA runs for the first time it will attempt to calibrate all controllers and or serial ports that were installed Press the Esc key on the keyboard to terminate or skip calibration for any monitor or allow the program to time out as indicated by the progress bar reaching maximum 19 Appendix A Multiple monitors USB controllers 1 Follow the procedure for Single monitor USB controller installa tion above The driver files will install When the
21. s should be inserted between the issuance of a reset com mand and any other command FPM 3171 User Manual 14 Communication Parameters Baud Rate 9600 default and 17200 bps e 8 Data bits 1 stop bit no parity only Interface USB Conforms to USB Revision 1 1 If the USB is connected to the controller the controller will communicate over the USB and will not communicate over the serial port The touch screen control board is never powered from the USB it is self powered only Operating Modes Full AccuTouch SmartSet protocol Emulation of E281A 4002 protocol can be selected by SmartSet command Initial Stream Untouch Z axis Enable Modes Touch Resolution 4096x4096 size independent Conversion Time Approximately 10 ms per coordinate set A 2 Resistive Touchscreen Driver Installation A 2 1 Hardware Touchscreen controllers must be configured for the driver prior to instal lation Elo typically ships controllers in a default setup that is compatible with this driver Controller requirements are Serial Serial controllers must conform to these minimum requirements e Baud rate 9600 baud e Data format SMARTSET e Itis desirable for a full handshaking connection to be established between the touchscreen controller and the computer but it is not required The controller will function with this driver in a two wire Receive Data and Ground RxD and Gnd configuration The conse quences of a two wire connecti
22. sc key on the keyboard to terminate or skip calibration for any monitor or allow the program to time out as indicated by the progress bar reaching maximum The program will continue until all controllers and or ports have been calibrated FPM 3171 User Manual 20 Silent Install The EloSetup program for this driver may also be run as an attended or unattended program from a command line batch file etc Example usage To Silent install for USB controllers use EloSetup iu s To Silent install for a Serial controller on COM1 use EloSetup is P 1 s To view all the options available for this installation method run EloSetup as EloSetup h EloSetup Parameters ELOSETUP US Uu lu L ils P lt port num gt lt port num gt 4 UC lt filename gt H Silent Install Uninstall Install USB drivers Install Serial drivers Install For specified Serial Com Ports lt port num gt Port number s of Elo Serial devices e g ELOSETUP IS P 1 2 where 1 is COM1 and 2 is COM2 Perform auto detection of serial com ports Run either EloCust exe or optional lt filename gt provided after installation Display options Display options e Adding Additional Serial Controllers Click on the Change option from the Add Remove programs in the Con trol Panel Elo entry 21 Appendix A Add or Remove Programs Elo XP Universal Driver k here for Elo Touchscreen Configuration FPM 3171 User M
23. t you selected should be checked in the list If you agree with the selection click Next and proceed to the next screen 6 The COM port you selected will be shown in the window of this screen This is your last opportunity to change your COM port selection before the driver files are installed Use the Back but ton s to change any of the selections you previously made Click Next to complete the installation of the driver files 7 Depending on the revision of the driver you are installing Win dows may advise you that the software you are installing has not passed Windows logo testing Select Continue Anyway to proceed with the installation This message can be suppressed in future installations by changing the selection in Driver Signing Options at Control Panel gt System gt Hardware gt Device Man ager gt Driver Signing 8 When the Setup Complete screen appears you may choose to run calibration the Elo Video Alignment program EloVA immedi ately or wait until later If you choose not to run this program now you can run it from the Elo Control Panel application Elo Touchscreen Setup Setup Complete Setup has finished installing the Elo touchscreen drivers and components You can choose to calibrate your Elo Touchscreen monitors after setup finishes Calibrate Elo Touchscreen monitors I View readme Click Finish to exit Setup FPM 3171 User Manual 18 Single monitor USB cont
Download Pdf Manuals
Related Search