Use and Care Manual
Contents
1. full power for approximately two hours to get rid of the unpleasant odour Make sure that the room in which the appliance is located is well ventilated during this operation It is normal for the appliance to emit small cracking sounds when you turn it on the first time Do not be alarmed IMPORTANT INSTRUCTIONS When using electrical appliances basic precautions should always be followed to reduce the risk of fire electric shock and injury to persons or property including the following 1 Read all instructions before using this heater 2 This heater is hot when in use To avoid burns do not let bare skin touch hot surfaces Use handles when moving this heater Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least 3 0 9 m from the front and top of the heater and keep them away from the sides and rear Keep the rear grille away from walls or drapes so as not to block the air intake 3 Extreme caution and supervision is necessary when any heater is used by or near children or pets and whenever the heater is left operating and unattended 4 Always unplug heater when not in use 5 Do not operate heater with a damaged cord or plug or after the heater malfunctions or has been dropped or damaged in any manner Discard heater or return to an authorized service facility for examination and or repair 6 Do not use outdoors 7 This heater is not intended for use in bathrooms lau2. the appliance grasp the plug and remove it from the outlet 4 Before each use inspect the line cord for cuts and or abrasion marks If any are found the appliance should be serviced and the line cord replaced Please return it to our Service Department or to an authorized service representative 5 NEVER wrap the cord tightly around the appliance as this could place undue stress on the cord where it enters the appliance and could cause it to fray and break 6 DO NOT operate appliance if the line cord shows any damage if the appliance works intermittently or stops working entirely 5 81609 01 R20150420 PARTS OF THE HEATER Parts of the Heater Symbols 1 Control Panel Power Button 2 Safety Grille 0 H L Heat Button 3 Remote Control D High Temperature Setting Button 4 Washable Air Filter Low Temperature Setting Button 5 Power Switch Timer Button 6 Power Light Figure 3 Figure 4 OPERATING INSTRUCTIONS Operation 1 Place the heater on a firm and level surface 2 Plug the cord set into a 120 volt AC outlet Be sure that the plug fits tightly into outlet When plugs fit loosely into receptacles they may slip partially or completely out of the receptacle with only the slight movement of the attached cord Receptacles in this condition may overheat and pose a serious fire hazard if covered by a curtain or drape the fire hazard is even greater 3 Turn on the Power Switch in the rear of the u
3. Infrared Heater With Remote Control Owner s Manual TABLE OF CONTENTS Tg 181810 116 OND se carttrotensneatr tom nitranattsaca une ddeattsainaiadelarsitusonasaiontaundarts 3 Safety and VVAlAING Six civiecbhancinuusioconviessurensecivadsesandeieadiceiar 3 Important Instructions rrrrererurnanerurnnvrrernnnenurnnnenuennvene 3 Grounding as en 0 EE 5 Parts of the TAC AG i uusrsmsekemteedeive npinsnendna 6 Operating INSUWUCNONS vc icccodescrccdcacddeadcncbameceisaceacddeopsuneasivncs 6 Tip over SWIG svensk ccteecicateudedcodnetatuararcihincvndesletececeantganshes 7 Thermal Protection System ccccccscccccsssseeeseesseeeseeees T IVIAINIG ANIC sigcssnsnctuntedirheieiecrruneibesiatunntsubiuibienetesiasozounnds 8 NN Aen ee E ee ee ee ee ee ee 8 Trouble ShoolnGguarasvsrsesunmmmuunmin n 8 Technical Supporuuamusmssmnamsideisrjeseredvs bkvssanvsin 8 KOG gt EE 9 ETE ERE EN 9 2 81609 01 R20150420 INTRODUCTION Thank you for choosing the Hunter Infrared Heater This manual gives you complete instructions for using your heater SAFETY AND WARNINGS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE INSTALL OPERATE OR MAINTAIN THE PRODUCT DESCRIBED PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND OR PROPERTY DAMAGE SAVE THESE INSTRUCTIONS FOR REFERENCE NOTE When switching on the appliance for the first time allow it to run at
4. OTING If your heater fails to operate e Make sure the electrical outlet or circuit breaker is working e Check for obstructions If you find an obstruction turn the heater OFF and UNPLUG THE UNIT Carefully remove the obstruction and follow the reset instructions TECHNICAL SUPPORT If you have any additional questions or problems with your Hunter Heater please call USA 1 888 880 3267 We open 24 hours a day 7days a week You may also reach us online at www HunterHomeComfort com An electronic copy of this user manual can also be obtained online at www HunterHomeComfort com 8 81609 01 R20150420 FCC WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by t
5. e touch A plug or cord which becomes hot to the touch or becomes distorted in shape may be a result of a worn electrical outlet Worn outlets or receptacles should be replaced prior to further use of the heater Plugging heater into a worn outlet receptacle may result in overheating of the power cord or fire 17 Always plug heaters directly into a wall outlet receptacle Never use with an extension cord or relocatable power tap outlet power strip 18 Check your heater cord and plug connections A loose fitting outlet can cause the plug to overheat or cause a fire Be sure plug fits tight in the outlet Check frequently during use to make sure plug and outlet are not hot If so discontinue using heater and have outlet replaced by a qualified electrician 19 Note Heaters draw more current than small appliances overheating of the outlet may occur even if it has not occurred with the other appliances 20 Check that neither the appliance nor the power cable has been damaged in any way during transportation 21 Make sure that no pieces of polystyrene or other packaging material have been left between elements of the appliance It may be necessary to clean the appliance 22 Connect to properly grounded outlets only 23 This appliance has a grounded three prong plug and is suitable for grounded receptacle use only An adapter is available for connecting three blade grounding type plugs to two slot receptacles The adapter must be p
6. e batteries out of the remote control if you won t use the remote control for a long time Remaining batteries may damage your remote control Note Do not mix old and new batteries Do not mix alkaline standard carbon zinc or rechargeable nickel cadmium batteries Figure 7 Battery Disposal Please dispose of the used battery per municipal or provincial law TIP OVER SWITCH This heater is equipped with a safety tip over switch This feature cuts the main power to the heater if it gets knocked over If the heater does tip over simply stand it upright in order to resume operation THERMAL PROTECTION SYSTEM This heater includes an Overheat Protection System that shuts the unit off when the unit reaches excessively high temperature If this occurs the heater can only resume its normal operation after resetting it To reset the heater 1 Turn off the power switch in the rear of the unit 2 Unplug the heater and wait 10 minutes for the unit to cool down 3 After the 10 minutes plug the unit in again and operate normally 7 81609 01 R20150420 1 Press the Power Button 1 and turn off the power switch in rear of the unit to turn the heater OFF unplug the heater before moving or cleaning 2 Interior dust can often be removed by using a vacuum cleaner with a crevice tool attachment 3 To clean the enclosure use a clean soft and lightly damp cloth to gently wipe off the dirt from the surface of the unit Be sure n
7. est service center or at our Service Department in Marietta Georgia IF THE USER OR CONSUMER PURCHASER CEASES TO OWN THE HEATER THIS WARRANTY AND ANY IMPLIED WARRANTY WHICH THEN REMAINS IN EFFECT INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE VOIDED NO WARRANTY EXPRESSED OR S AG D 81609 01 R20150420 IMPLIED INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE IS MADE IN RESPECT TO THE GLASS GLOBES OR LIGHT BULBS OR THE FINISH ON ANY METAL PORTION OF THE HEATER THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES THE DURATION OF ANY IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN RESPECT TO ANY HUNTER HEATER MOTOR OR OTHER HEATER PART IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH MOTORS AND OTHER PARTS This warranty is voided if your Hunter heater is not purchased and used in the USA This warranty excludes and does not cover defects malfunctions or failures of any Hunter heater which were caused by repairs by persons not authorized by us use of parts or accessories not authorized by us mishandling improper installation modifications or damage to the Hunter heater while in your possession or unreasonable use including failure to provide reasonable and necessary maintenance To obtain servicing contact the
8. itch Figure 5 Figure 6 81609 01 R20150420 After the display has shown 12 pressing the Timer Button e one more time will reset the heater to run continuously The heater will turn off when the set time has elapsed The unit can be turned back on by pressing the Power Button O Automatic Temperature Control 1 To set the room at a specific temperature press the or O buttons to the desired temperature The heater is now in Auto Temperature Mode 2 The set temperature will show for several seconds and then the display will return to indicate the current room temperature NOTE The temperature display does not indicate the temperature of the heated air being delivered by the heater 3 When the room temperature reaches 2 degrees above the set temperature the heater will shut off When the room temperature reaches 2 degrees below the set temperature the heater will turn back on and continue to cycle off and on to maintain the set temperature NOTE It is normal for the fan to run for 30 seconds when the heater shuts off after reaching the set temperature Remote Control Figure 7 1 The remote control uses two 2 AA batteries not included for operation 2 All the functions performed using the Remote Control work identically to the Manual Controls Note Change the batteries with new and same types if the remote control does not operate well Otherwise your remote control may not operate properly Remove th
9. ndry areas and similar indoor locations Never locate heater where it may fall into a bathtub or other water container 8 Do not run cord under carpeting Do not cover cord with throw rugs runners or similar coverings Do not route cord under furniture or appliances Arrange cord away from traffic area and where it will not be tripped over 9 To disconnect the heater turn control to OFF then remove the plug from the outlet 10 Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage to the heater 3 81609 01 R20150420 11 To prevent a possible fire do not block air intakes or exhaust in any manner Do not use on soft surfaces like a bed where openings may become blocked 12 A heater has hot and arcing or sparking parts inside Do not use it in areas where gasoline paint or flammable liquids are used or stored 13 Use this heater only as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock injury to persons or other damage to property 14 Ensure the heater is on a stable secure surface to eliminate the potential of tipping it over 15 To prevent overload and blown fuses be sure that no other appliance is lug ed into the same outlet receptacle or into another outlet receptacle wired into the same circuit 16 It is normal for the heater s plug and cord to feel warm to th
10. nearest Hunter authorized service center or the Hunter Home Comfort Service Department 1831 A West Oak Parkway Marietta GA 30062 Please contact us before shipping your heater to us If we authorize you to ship it to us you will be responsible for all insurance and freight or other transportation charges to our factory service center We will return your Hunter heater freight prepaid Your heater should be properly packed to avoid damage in transit since we will not be responsible for any such damage Proof of purchase is required when requesting warranty service The purchaser must present sales receipt or other document that establishes proof of purchase INNO EVENT SHALL HUNTER HOME COMFORT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE SINCE 1886 1831 A West Oak Parkway Marietta GA 30062 Hunter is a trademark of the Hunter Fan Company and is used under license to Hunter Home Comfort Printed in China 10 S AS D 81609 01 R20150420
11. nit Figure 5 4 There will be a beep sound and Power Light will come on indicating that there is power to the unit The Power Light will remain on until Power Switch is turned off Figure 5 5 Turn the heater ON by pressing the Power Button 1 6 Press the D and O buttons at the same time for two seconds to change the display to show the temperature reading in Celsius Press the same two buttons together again to change the display back to show the temperature reading in Fahrenheit 7 Upon turning the heater on the unit will be in HIGH heat 8 Press the 7 button to switch over LOW or HIGH heat 9 To turn the heater OFF press the Power Button C again The unit will turn off the heating elements Then turn off the Power Switch in the rear of the unit Power Light will go out indicating that the power is shut off Unplug the unit by pulling the plug from the electrical outlet Timer Function Figure 6 The timer function may be activated when the heater display is in any function This function allows you to set the length of time the heater will run before turning itself off from 0 hour to 12 hours 0 means there is no set running time and heater will run continuously Pressing the Timer Button will increase the length of time by 12 hour each time when this button is pressed LZ sii Va RE i il i miili Al SS TT pe A Dn gt Figure 3 Figure 4 Filter Cover Power Sw
12. ot to wet the Heating Element and the switches Allow the unit to dry completely before use 4 Do not use cleaning liquid or other chemicals to spray on the unit 5 This heater is equipped with an easy to clean washable static filter Regular cleaning and maintenance of your filter will ensure a lifetime of trouble free use e Turn off heater then locate the filter at the rear of the heater Loosen the 4 screws to remove the filter cover and take the filter out of the bracket Figure 5 e Rinse the filter by spraying warm tap water through the rear side of the filter opposite of air intake direction until the dust and debris are cleared e f the filter is extremely dirty or clogged with grease you can soak the filter in a mild solution of dish soap such as Dawn and water then brush with a soft brush and repeat rinsing process e Shake the filter to remove excess water and lay on clean cloth or paper towels to dry Do not use heat source to dry the filter e Replace the filter in the bracket Align the holes of the filter cover and tighten the 4 screws NOTE Never operate heater without filter in place Without the filter in place dust can accumulate on the infrared heaters causing damage aa ACCC 1 Perform the cleaning procedures described above 2 Wipe all parts dry 3 Pack the heater in a plastic bag and store it in a cool dry place We recommend that you store the heater in its original carton TROUBLE SHO
13. roperly grounded Do not attempt to defeat the purpose of this safety feature CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN NO USER SERVICEABLE PARTS INSIDE DANGER HIGH TEMPERATURES MAY BE GENERATED UNDER CERTAIN ABNORMAL CONDITION DO NOT PARTIALLY OR FULLY COVER OR OBSTRUCT THE FRONT OF THIS HEATER FOR HOUSEHOLD USE ONLY SAVE THESE INSTRUCTIONS 4 81609 01 R20150420 GROUNDING INSTRUCTIONS F This appliance is for household use only and may be plugged into any 120 volt AC electrical outlet ordinary household current DO NOT use any other type of outlet WARNING This unit is suitable for grounded receptacle use only Grounding Grounded Outlet in Box Cover The cord has a grounded plug as shown in Figure 1 An adapter as shown in Figure 2 is available for connecting three blade Figure 1 grounding type plugs to two slot receptacles The green grounding lug extending from the adapter must be connected to a permanent ground such as a property grounded outlet box The adapter should not be used if a three slot grounded receptacle is available NOTE The adapters ARE NOT supplied with this heater Read follow and save the instructions that are included with the adapter Adapter you choose LINE CORD SAFETY TIPS 1 NEVER pull or yank on the cord or the appliance Grounding Grounded Outlet Means Box Cover 2 To insert plug grasp it firmly and guide it into the outlet Figure 2 3 To disconnect
14. urning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help WARRANTY Hunter Home Comfort makes the following limited warranty to the user or consumer purchaser of this Hunter heater If your Hunter heater motor fails at any time within three years after the date of sale to you due to a defect in material or workmanship labor to repair the defect will be provided free of charge at our nearest service center or our Service Department in Marietta Georgia You will be responsible for labor costs after this three years period The foregoing limited warranty applies only to the motor itself and does not apply to electronic controls such as remote controls remote control receivers or transmitters used in conjunction with the motor These electronic control items are included in the one year limited warranty below If any part of your Hunter heater other than the motor fails at any time within one year after the date of sale to you due to a defect in material or workmanship we will repair or at our option replace the defective part free of charge for parts and labor performed at our near
Download Pdf Manuals
Related Search