XD-V35 Digital Wireless Pilot`s Handbook - Revision A
Contents
1. signal strength quality with transmitter off red lights indicate interference on that channel Audio LED Green when audio signal present Power LED Blue when on Unbalanced 1 4 Inch Audio Output Connector Balanced XLR Audio Output 9VDC Power Input Connector Plug the power supply cable into the receiver and AC power receiver will turn on Turn the rotating Channel Select knob to the desired channel must match transmitter channel Connect with an audio cable to a mixer or similar The receiver is ready to use Note The receiver antenna is internal www americanmusical com Bodypack Transmitter TEPOG TRANSMITTER I Audio LED Green when audio signal present 2 Battery Level LED Blue with good level red when low flashing red when less than 40 minutes remain On Off Slide Switch Channel Select Slide Switch Quarter Inch 1 4 TRS Input Connector Sn fl Battery Door Slide switch and hinged door Open the battery door on the side of the bodypack and insert two AA batteries Slide the On Off switch to turn on Slide the Channel Select button to select match the channel number with the receiver channel The transmitter is ready to use Note The bodypack transmitter features a belt clip to secure it to a belt or other clothing Www americanmusical com Handheld Transmitter l Power Button Press briefly to turn on press and hold for two seconds to turn off 2 Channel Select Button Channel2. the associated transmitter turned on you will see depending on the distance between the transmitter and receiver all three or the bottom one or two RF LEDs lit green on the right side of the Trans Status window e Depending on the condition of the transmitter batteries you will see all three or the bottom one or two battery status LEDs lit green on the left side of the Trans Status window If the battery level is low the bottom LED will turn red and it will flash red when 40 minutes or less remain e When you speak or sing into the microphone the green Audio LED will light e Connect to the audio system using the rear panel Balanced XLR Audio Output or Unbalanced Www americanmusical com 1 4 Inch Audio Output Note the signal output from either of these connectors is mic level and the receiver has no gain or attenuation controls A Do not use TRS connectors with the XD V35 Receiver as the Ring portion of the connector is used for firmware updates and may cause computer generated noise in your audio outputs Note When the associated transmitter is off and moderate to strong interfering frequencies not coming from a Line 6 transmitter are present on the selected receiver channel one or more of the RF LEDs on the right side of Trans Status will turn red Higher levels of interference will light more red LEDs Use in high interference conditions will result in reduced range for the system Either move the receiver away from the so
3. D will light Www americanmusical com e When the transmitter is on the same channel number as the receiver the receiver Trans Status LEDs will light green and when you speak in the mic the receiver Audio LED will light green CONNECTING THE XD V35 RECEIVER The receiver features a balanced XLR and unbalanced tip sleeve quarter inch connector To connect to a mixing board or powered mixer use a microphone cable between the receiver output and the mixer s mic level input in the same way as you would connect a wired microphone The output of the XD V35 receiver is virtually identical to that of the microphone on the transmitter or other standard wired mic To connect to an instrument amplifier or other audio equipment with a quarter inch connector such as a signal processor or effects unit use a 1 4 to 1 4 instrument cable This output is also mic level Microphone Usage Tips Try to maintain a constant distance and relationship between the user s mouth and the microphone In live theatre this is often done by placing a small mic in the hairline toward the front side of the head or right above the ear With mic placement on the collar or shoulder area changes in level can occur as the user s head turns experiment with the location of the mic to minimize this effect Mic placement in the center of the chest can help with the level changes but is farther from the voice and quite shielded from the direct energy of the voice
4. Www americanmusical com Lane Fy XD V39 Digital Wireless Pilot s Handbook Manuel de pilotage Pilotenhandbuch Pilotenhandboek Manual del Piloto FIRES 40 00 0335 also available www line6 com manuals RevA Www americanmusical com t Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING T0 REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT REMOVE SCREWS NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING 10 REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE CERTIFICATION THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFER ENCE THAT MAY CAUSE UNDESIRED OPERATION Warning Changes or modifications not expressly approved in writing by Line 6 may void the users authority to operate this equipment RF Exposure Statement This transmitter must not be co located or operated in conjunction with any other antenna or transmitter Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interfer ence in a residential installation This equipment generates uses and can radiate radio frequen
5. cy energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communica tions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equip ment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This Class B digital apparatus complies with Canadian ICES 003 This Category II radio communication de vice complies with Industry Canada Standard RSS 310 Cet appareil numerique de la classe B est conforme a la norme NMB 003 du Canada Ce dispositif de radiocommunication de cat gorie II respecte la norme CNR 310 d Industrie Canada The FCC compliance sticker is attached to the THH06 battery compartment Remove the THH06 base by unscrewing counter clockwise to see this compliance sticker Www americanmusical com You should read these Important Safety Instructions Keep these instructions in a safe place Before using your XD V35 Digital Wireless System carefully read the applicable items of
6. e XD V35 system ships set to the new dual frequency RF2 mode To use an XD V35 version transmitter with an earlier generation XD V30 receiver RF1 mode you must change the transmitter from RF2 mode to RFI mode The method differs slightly between the handheld and beltpack THHO06 Handheld Transmitter e Turn the transmitter off e Press and hold the channel SELECT button e While holding the SELECT button press and hold the power ON button e The blue LED over channel 1 will flash three times to indicate that the transmitter is in the RFI mode To revert to the RF2 mode repeat the above steps the blue LED over channel 2 will flash three times when the transmitter is in this mode TBP06 Beltpack Transmitter e With transmitter off set the Channel Select slide switch to channel 6 Turn on the transmitter e Wait for the blue LED to flash followed by a green LED flash Immediately slide the Channel Select switch completely left to channel 1 e Quickly slide the Channel Select switch completely right to channel 6 e This process must be completed within three seconds of turning on the transmitter e The blue LED will flash once to indicate that the transmitter is now in the RF1 transmission mode To revert to RF2 transmission mode repeat the above steps the blue LED will flash twice when the transmitter is in this mode Www americanmusical com XD V35 Digital Wireless System Specifications System Frequency Band Compat
7. ible Channels Spatial Diversity with Digital Buffering Frequency Diversity Compander Free Design Frequency Response THD System Latency Operating Temp Range Range Receiver RF Signal Strength Indicator Battery Level Indicator Audio Presence LED Squelch amp Pad adjustments Receiver Antennas Receiver Format Receiver Power Requirements Output Impedance Sensitivity Image Rejection Transmitters Transmitter RF Output Power Battery Life Batteries Battery Level Display Dynamic Range THH06 Handheld TBP06 Beltpack TBP06 Maximum Audio Input Level TBP06 Beltpack Input Impedance TBP06 Beltpack Supplied Bias Voltage 2 4GHz ISM Band 6 Yes Yes 2 Frequencies per channel Yes 10 Hz 0 5 dB 20kHz 2 5 dB 0 03 typical lt 3 5 ms audio input to output 0 50 degrees C up to 275 feet 90 meters Actual range will depend on nearby RF interference sources including line of site obstacles 3 Segment LED 3 Segment LED Yes None required Internal Table Top 9Vdc 200mA XLR 150 Ohms Balanced 1 4 1 kOhm Unbalanced 95 dBm 56 dB 10 mW 8 hours 2 x AA Alkaline Low Battery LED gt 115 dB gt 118 dB 6 5 Vpp 1 3 M Ohms 5 VDC on Pin 2 of TA4F Connector Pinout To TBP06 Beltpack 1 4 TRS Connector e Tip Signal Ring Bias Voltage 5 VDC e Sleeve Ground
8. s 1 6 3 Channel LEDs Lights blue to show current active transmission channel Channel 6 LED illuminates red when battery life is low and blinks red when less than 40 minutes remain Unscrew the transmitter base and insert two AA batteries Push the On button to turn on Press the Channel Select button to set the channel indicated by LED position on display match the channel number with the receiver channel The transmitter is ready to use XD V35 Receiver DETAILED SETUP The receiver is quite simple to set up This section adds a few useful details e When used stand alone position the receiver on a surface that provides line of sight or at least near line of sight with the location where the transmitters will be used This will help maximize the range e Connect the provided DC 1G power supply to the 9VDC 200mA connector on the rear panel to secure press a loop of the cable through the cable holder located to the left of the connector to prevent accidental disconnection Plug the power supply into an available AC outlet that provides voltage from 90 240 VAC at 50 or 60 Hz its LED lights green when power is active at the outlet e The blue Power LED on the front panel will light and the receiver is on e Turn the Channel Select knob to point to channel 1 through 6 The channel number on the receiver and its associated transmitter must match When using multiple receivers set each one to a different channel number e With
9. so typically provides a hollow midrange or chest sound to the voice The V35 Belt Pack transmitter includes a built in roll off filter Walk Testing the Performance Area When first setting up a wireless system in a new location it is good practice to position the receivers where they will remain during the event and then walk the entire performing area with the audio system on and the transmitter active Talk and listen for signal dropouts or other problems and note where they are with respect to your receiver placement If possible reposition the receiver to obtain better coverage and improve or eliminate areas with lower signal strength by improving line of sight to the transmitter Www americanmusical com APPENDICES Troubleshooting Problem Solution No Audio Transmitter off or battery out of power Batteries put into transmitter out of polarity Transmitter and receiver on different channels Receiver off unplugged or not connected Can t Turn Off Transmitter Transmitter in locked mode THH06 handheld only Change Channels Loss of Signal Distance between transmitter and receiver is too great Dropouts Other transmitting or RF devices are too close to the receivers Shorter Range Receiver not in line of sight with transmitter Interference on channel change channels Another Line 6 transmitter is turned on and set to the same channel Setting THH06 and TBP06 Transmitters to XD V30 Compatibility Mode Th
10. stem It is a high quality digital wireless system in a simple format that is virtually plug and play With its fully digital transmission the system provides features and benefits that differ in some ways from previous generations of analog wireless but in most respects you use it just like other wireless systems By understanding a few simple concepts you ll be able to achieve superior audio quality a secure and dropout free signal and the ability to use multiple channels of wireless together without interference or other conflicts e Digital transmission in the 2 4 GHz band license free operation worldwide e Avoids interference from high power TV transmitters in the UHF bands Digital technology provides the audio response of a cable without companding 24 bit digital converters 118 dBA dynamic range and 10 Hz 20 kHz bandwidth e System latency lt 3 5 ms e Proprietary two frequency transmission promotes reliable dropout free performance e Compatible with existing WiFi installations e Fast setup gain squelch or level adjustments not required e 6 channels that work together simultaneously e 275 foot 90 meter range e Transmitter life gt 8 hours on two AA alkaline batteries e Battery level and RF LED meters e Table top receiver with internal antenna e XLR and 4 TRS output connectors e Designed for compatibility with previous XD V30 systems RECOMMENDATIONS FOR Best PERFORMANCE Maintain a clear line of sight be
11. t red and it will flash red when less than 40 minutes remain Line 6 transmitter battery life meters are calibrated for use with alkaline batteries so when NiMH rechargeable batteries are used the remaining life will not be as accurate however the basic indication is to insert fresh batteries soon after the LED shows red Carbon zinc batteries are not recommended TBPO6 BELTPACK TRANSMITTER DETAILED SETUP e With a thumbnail slide down the latch on the battery door located on the right side of the transmitter e Open the hinged door and insert two AA batteries noting the polarity markings shown on the top plate of the battery compartment Use alkaline batteries or rechargeable NiMH batteries in the 2400 2800 mAh range Close the battery cover and slide the latch up with your thumbnail to lock Slide the switch on the top of the transmitter to ON the LED marked Batt battery will light blue Note When the transmitter battery level is low the Batt LED will light red and it will flash red when less than 40 minutes remain e On the face of the transmitter the Channel select provides a metal slide switch to set a channel from 1 to 6 Slide the metal button to the desired channel number it has detents so it will stop in the correct place The channel is selected and active immediately e Connect the lavalier microphone to the 1 4 TRS tip ring sleeve jack on the bottom of the transmitter When you speak in the mic the Audio LE
12. these operating instructions and the safety suggestions l Ls J Obey all warnings in the XD V35 manual Do not perform service operations beyond those described in the XD V35 Manual Service is required when the apparatus has been damaged in any way such as liquid has been spilled or objects have fallen into the apparatus the unit has been exposed to rain or moisture the unit does not operate normally or changes in performance in a significant way the unit is dropped or the enclosure is damaged Do not place near heat sources such as radiators heat registers or appliances which produce heat Guard against objects or liquids entering the device Do not use or place unit near water Do not step on cords Do not place items on top of cords so that they are pinched or leaned on Pay particu lar attention to the cord at the plug end and the point where it connects to the device Clean only with a damp cloth Only use attachments accessories specified by the manufacturer Prolonged listening at high volume levels may cause irreparable hearing loss and or damage Always be sure to practice safe listening CE G AAT r 1201 1 eDanaret OVANATEL 1773 11 6586 C ROHS oeda OE 014 ill AM 95 EC m 3794 0107899153000011 1 07899153010271 Fe Www americanmusical com Thank you for your purchase of the XD V35 wireless microphone sy
13. tween the transmitter and receiver s internal antennas Typically the receiver should be placed at table top or higher level Avoid placing the receiver in the bottom of the rack or behind walls and obstructions e When transmitters are used at a greater distance place receivers closer to them and use XLR mic or 4 cables to connect to the audio system Avoid placing the receiver in close proximity to RF generating equipment including computers wireless access points in ear monitor transmitters and microwave ovens Avoid blocking antennas in the transmitters Do not cup the bottom of the handheld transmitter Avoid placing the bodypack transmitter in pockets SUPPLIED COMPONENTS XD V35 Receiver receiver 9V 0 5A external universal power supply user s manual THHO06 Handheld Microphone transmitter two 2 AA alkaline batteries mic stand clip or TBP06 Bodypack Transmitter transmitter two 2 AA alkaline batteries unidirectional lavalier microphone with windscreen and clip Www americanmusical com XD V35 Dicitat WIRELESS Quick SETUP Receiver gt S 3 lt S 9 246Hz DIGITAL WIRELESS SYSTEM 6 Position Channel Select Knob Battery Level Indicator LEDs Lights green with all lit indicating full transmitter battery bottom LED turns red when 1 hour remains and flashes red when less than 40 minutes remain Transmitter Signal Level Indicator LEDs RF lights green to indicate transmitter
14. urce of the interference such as a nearby WiFi modem or computer with a WiFi transceiver or select another channel not showing interference THHO6 HANDHELD TRANSMITTER DETAILED SETUP e Twist the bottom section of the THH06 transmitter counterclockwise unscrew and remove it Lightly pull the battery cover tab down with a thumbnail and open the cover by pulling back it is hinged at the base of the transmitter o Insert two AA batteries noting the polarity markings shown in the battery compartment Use alkaline batteries or rechargeable NiMH batteries in the 2400 2800 mAh range Close the battery cover and replace the bottom section of the transmitter Press and briefly hold the left button below the Channel display to turn on A small blue LED will light under the currently selected channel Press the right Select button to change to the next channel the blue LED above the number will light Each press of the button will go to the next channel The channel is selected and active immediately Note the transmitter buttons are recessed to prevent accidental activation so press them down firmly below the recessed surface until you feel a click e When the transmitter is on the same channel number as the receiver the receiver Trans Status LEDs will light green and when you speak in the mic the receiver Audio LED will light green Note When the transmitter battery level is low the LED over the number 6 on the display will ligh
Download Pdf Manuals
Related Search