Home

810DTC/810DT+ Pentium II/III Celeron Twin Processor

1. 3 10 Intel810 Baby AT Mainboard HARDWARE SETUP 3 3 18 CN17 Chassis Fan Power Connector FAN2 The Chassis fan power connector can be connected to the chassis fan so that it will reduce the temperature inside the PC system 1 Ground 2 12V DC 3 Fan Sense Signal 3 3 19 CN18 Audio Game Connector There is the 3D PCI audio interface installed on the mainboard Please refer to the following picture for the connection 3 11 Intel810 Baby AT Mainboard HARDWARE SETUP In order to have the audio device connected to the Audio Game port an adapter is required Please refer to the following picture for the connections on the adapter GAME MID
2. Installation of DIMM modules 1 Outlook of DIMM modules a Single Side DIMM Module SS Double Side DIMM Module 2 Minimum one DIMM module must be installed on the mainboard 3 Please use 3 3V PC 100 un buffered DIMM module 4 You can use single side or double side DIMM module on this mainboard 5 Only PC 100 DIMM module or above is recommended on this mainboard 6 Please install the DIMM module starting from DIMM first 7 Maximum memory size 512MB 1 When CPU booster is not installed on the mainboard you O can choose either PC 100 or PC 133 DIMM module 2 When CPU booster is installed on the mainboard PC 133 DIMM module is recommended 3 2 Intel810 Baby AT Mainboard HARDWARE SETUP 3 3 CONNECTORS A series of connectors are designed on the mainboard to make connection with the accessories or peripheral devices such as power mouse printer etc Followings are the connectors with its description and the pin assignment which is designed on the mainboard 3 3 1 BAT1 Battery Socket Use the 3 Volts Lithium battery CR2032
3. Note please contact your dealer for the TV converter so that you will get the proper TV OUT converter Wrong TV converter may destroy the mainboard 3 13 Intel810 Baby AT Mainboard HARDWARE SETUP 3 3 23 CN25 AIR Bus Connector The AIR Bus is a revolutionary technology and it will provide you lots of amazing features and it will rescue your PC system from virus attack Please refer to the following picture for the AIR Bus interface Please refer to section 1 2 for detail function description CN25 AIR Bus Connector 3 3 24 Push buttons and LED connectors A series of connectors are designed on the board to connect the push buttons and LED indicators Followings are the details Reset Button connector eeeee HDD LED connector Turbo LED connector Soft Off LED connector
4. I O address 3F8H 2F8H 3E8H 2E8H IRQ3 IRQ4 selected by CMOS setup 3 3 6 5 Parallel Port Connector Supports SPP EPP ECP modes IRQ7 or 5 is selectable ECP mode will use either DMA channel 3 or channel 1 which can be selected by the CMOS setup program Parallel Port Jl 3 5 Intel810 Baby AT Mainboard HARDWARE SETUP 3 3 7 CN6 USB Port 1 Universal Serial Bus Connector 3 3 8 CN7 USB Port 2 Universal Serial Bus Connector p T CN8 FDC Connector Intel810 Baby AT Mainboard HARDWARE SETUP 3 3 10 CN9 IDE 1 Connectors Primary IDE Port 1F0H IRQ 14 3 3 11 CN
5. Battery Socket Pinf Pin name Pin Pin name Battery Positive Ground 3 3 2 CN1 Keyboard Connector Keyboard Connector Intel810 Baby AT Mainboard HARDWARE SETUP 3 3 3 CN2 PS 2 Mouse Connector 1 e Mouse Data No Connection Ground PS 2 Mouse Connector 3 3 4 CN3 Serial Port COM 1 Connector Intel810 Baby AT Mainboard HARDWARE SETUP 3 3 5 CN4 Serial Port COM 2 Connector
6. 4 23 4 15 SAVE amp EXIT SETUP EXIT WITHOUT SAVING 4 24 5 UPDATE THE SYSTEM BIOS 5 1 Intel 810 Baby AT Mainboard SOMETHING IMPORTANT TRADEMARKS All trademarks used in this manual are the property of their respective owners LOAD SETUP DEFAULTS LOAD SETUP DEFAULTS is the function which will have the BIOS default settings loaded into the CMOS memory These default settings are the suggested settings which will optimize system performance and increase system stability Load the setup default is recommended when you receive this mainboard or when the system CMOS data is corrupted Please refer to the Section 4 8 for the procedures DISCHARAGE CMOS DATA Whenever you want to discharge the CMOS data or open the system chassis Make sure to disconnect the AC power first because there is always the 5V standby voltage connected to the ATX form factor mainboard Without disconnecting the AC power connector from the PC system the mainboard can be damaged by any improper action Xx WAKE ON LAN In order to support the Wake On LAN feature the system requires a special SPS Switching Power Supply Such power supply must be able to provide at least 800 mA of driving capability on the 5V standby voltage Please refer to the Section 3 3 for pin assignment WARNING The Static
7. If you lost the CMOS data or you don t know how to complete the setup procedure you may use this option to load the Optimized default values from the BIOS default table The optimized default value is the suggested setting which will give the best reliability and also the good performance Incase that the CMOS data is corrupted or if you made some CMOS setting and found that the PC system becomes very stable then you may try to load the optimized default value and the CMOS will be changed to its default setting 4 21 Intel810 Baby AT Mainboard AWARD BIOS SETUP 413 SET SUPERVISOR PASSWORD CMOS Setup Utility Copyright C 1984 1999 Award Software Standard CMOS Features Frequency Voltage Control Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Integrated Peripherals Set User Password Power Management Setup Save amp Exit Setup PNP PCI Configuration Exit Without Saving PC Health Status ESC Quit tl lt Select Item F10 Save amp Exit Setup Time Date Hard Disk Type The password entry in this field is different to the Power On Function mentioned in Section 2 2 and Section 4 7 Those password settings are used to power on your PC system However the SUPERVISOR PASSWORD will be used to check the authority when power on the PC system The Supervisor Password will have different function according to the
8. PW SL TL HL RS Power On Off Suspend switch Intel810 Baby AT Mainboard HARDWARE SETUP 1 RS Reset Button Connector Pin Signal name Pinl amp 2 Function 1 Reset Control Open No action 2 Ground Short System Reset 2 HL IDE HDD LED Connector Pin Signal name 1 5V DC Pull up 2 HDD Active Signal 3 TL TURBO LED Connector Pin Signal name 1 5V DC Pull up 2 GND 4 SL Soft OFF LED Connector S5 State This LED will be used to indicate the status of Soft Off S5 state When the PC system is power off there is still the standby 5V active When this LED is lightened it means that the AC power is connected to the PC system When darkened the AC power is disconnected or the system is powered on Pin Signal name 1 Signal Pin 2 Ground When the PC is in the Soft OFF state please do not install or remove any component from the mainboard because the standby electricity is still active Please remove the power cable from the electricity outlet before you can proceed with the installation remove Otherwise it will cause SERIOUS DAMAGE TO YOUR PC SYSTEM 3 15 Intel810 Baby AT Mainboard HARDWARE SETUP 5 PW Power On Off and External Suspend Switch Connector If you are using the ATX power supply the PW connector will have two different functions according to the setup in CMOS It can be the Power Switch or Suspend Switch of your PC system please ref
9. to raise the CPU voltage it does not mean that CPU over clock is suaranteed D JP6 Clear CMOS Data Button In case that you made improper setting in the CMOS setup program and cause the PC system not working you may use JP6 to clear all the setting which is recorded in the CMOS memory 1 2 Short Normal Setting 2 3 Short Clear CMOS 3 20 Intel810 Baby AT Mainboard HARDWARE SETUP Note Improper BIOS setting may cause hang up to the PC system Should it be happened you may use JP6 to clear the information which is stored in the CMOS memory and get the PC system back to normal Improper connection may cause permanent damage to the mainboard Please refer to the following steps to clear the CMOS T Unplug the AC power cable from the PC system 2 Put the mini jumper on pin 2 3 of JP6 around 3 to 5 seconds and then return it to the original position pin 1 2 3 Re connect the AC power cable E JP7 Clear Keyboard Password In case that you forget the keyboard password which you selected in the CMOS setup program you will be unable to start your PC system please refer to Section 4 7 POWER ON FUNCTION In this case you can us
10. One Cable set for IDE and Floppy COM port etc devices One Retention Mechanism It is mounted on the mainboard One CD diskette for device driver and utility programs This mainboard contains electrostatic sensitive components and it can be easily damaged by static electricity So please leave it sealed in the original packing until when installing A grounded anti static mat is recommended when unpacking and installation Please also attached an anti static wristband to your wrist and have it grounded to the same point as the anti static mat After the opening of the mainboard carton please observe the mainboard carefully to make sure there is no shipping and handling damage before you can start to install the PC system Having finished all the procedures above you are now ready to install the mainboard to the chassis Please make sure that the chassis is designed for the Baby AT mainboard so that the mounting hole will match with this mainboard This mainboard supports both AT and ATX type of power supply You may connect either type of the two power supply and this mainboard will detect the power supply automatically Intel810 Baby AT Mainboard INTSTALLATION 2 2 ACPI FUNCTION FOR ATX POWER ONLY This mainboard has the ACPI Advanced Configuration Power Interface designed on the board If you have the ATX type power supply connected to the mainboard there are several ways to power on the system Please read the following de
11. These fields allow you to decide the sequence of the boot devices Swap Floppy Drive default setting Disabled When enable this option the device name of the floppy drives will be swapped For example drive A will be treated as drive B and drive B as Drive A Boot Up Floppy Seek default setting Disabled When enabled the floppy drive will be initialized during POST Boot Up NumLock Status default setting When enabled the NumLock LED will be lightened after the POST Typematic Rate Setting default setting Disabled This selection field allows you to adjust the frequency of keyboard control signal If your typing speed is really and you feel the response from the PC system is too slow then you may select Enabled in this field and select the parameter which will meet your requirement Typematic Rate Chars Sec default setting 6 This field allows you change the typing rate You may use this field to select how many characters per second which you feel like to have Basically the default speed defined in the system BIOS will meet most requirement So you do not have to change the setting here unless your typing is really fast faster than the computer Typematic Delay Msec default setting 250 The purpose of this field will let you adjust the time interval between the typing If may change the parameter here she shorter the faster and then select the proper setting for yourself
12. Copyright C 1984 1999 Award Software Standard CMOS Features Date mm dd Wed Oct 27 1999 Item Help Time hh mm ss 16 03 33 IDE Primary Master Press Enter 1707MB Menu Level gt IDE Primary Slave Press Enter None gt IDE Secondary Master Press Enter None Change the day month gt IDE Secondary Slave Press Enter None Year and century Drive A 1 44M 3 5 in Drive B None Floppy 3 Mode Support Disabled Video EGA VGA Halt On All Errors Base Memory 640K Extended Memory 63488K Total Memory 64512K IDE Primary Secondary Master Slave These two selection fields allow you to select the HDD type which is installed on the IDE port Move the selection bar to the appropriate field and then click on the ENTER key and the system BIOS will detect the DHH type automatically Drive A B These two selection fields allow you to select the type of the floppy drive Check the floppy drive installed in the system and then use this field to select the correct type Floppy 3 Mode Support Default setting disabled This mode is for Japanese 3 5 inch high capacity floppy disk drive If you have such drive installed in the PC system please select enable otherwise use the default setting Video This selection field allows you to select the display mode Check the video display card installed in the PC system and then use this selection field to choose the proper display mode
13. Intel810 Baby AT Mainboard AWARD BIOS SETUP POWER ON Function Default setting BUTTON ONLY The Power ON function allows you to select different way to power on your PC system KB Power ON Password When you select KB Password to power ON the PC system In the previous selection field you may enter your personal password in this field When finished you may use the password to power on your PC system Hot Key Power ON When you select KB Password to power ON the PC system in the previous selection field you may select a set of Hot Key in this field When finished you may use the combination of hot key to power on your PC system Onboard FDD Controller Default setting Enabled This should be enabled if your system has a floppy disk drive FDD installed on the system board and you wish to use it Even when so equipped if you add a higher performance controller you will need to disable this feature The Choice Enabled Disabled Onboard Serial Port 1 Port 2 Default setting 3F8 IRQ4 2F8 IRQ3 This item allows you to determine access onboard serial port 1 port 2 controller with which I O address The Choice 3F8 IRQ4 2F8 IRQ3 3E8 IRQ4 2F8 IRQ3 Disabled Auto UART 2 Mode Default setting Normal This item allows you to determine which Infra Red IR function of onboard I O chip The Choice Normal ASKIR IrDA Onboard Parallel Port Default setting 378 IRQ7 Select a logic
14. 4 5 Intel810 Baby AT Mainboard AWARD BIOS SETUP Security Option default setting Setup This selection field allows you to select how to secure the PC system for you There are two choice selectable Setup and System Before you can apply the security option to your PC system you have to select your own Supervisor Password or User Password in the BIOS setup program When Setup is selected you will have to input your Passwords before you can start the BIOS setup program When you select System you will be unable to load the operation system if you don t key in your personal password PS 2 mouse function control default setting Enabled This mainboard built in a PS 2 mouse port In case that you prefer to connect a serial mouse to the serial port instead of using the PS 2 mouse you may choose Disable in this field so that the IRQ12 can be released for the other devices If you are using the PS 2 mouse please leave this field Enabled OS Select For DRAM gt 64MB default setting Non OS 2 When you are using the OS 2 operating system and the system memory is more than 64MB you will have to select the setting to 052 otherwise leave this on the default setting Non OS2 for all other operating systems HDD S M A R T Capability default setting Disabled There is the HDD which support the S M A R T technology Self Monitoring Analysis Reporting Technology If yo
15. This mainboard provides the virus warning features in the BIOS During and after the operation system is loaded any attempt to write to the boot sector or partition table on the IDE hard disk drive will trigger this feature and give you the warning message on the screen and then halt the system When you find the message on your screen please run the anti virus program to see whether your system is infected by a virus or not Enabled A warning message will be displayed on the screen when something attempts to access the boot sector or hard disk partition table Disabled No warning message will appear on the screen when anything attempts to access the boot sector or hard disk partition table 4 4 Intel810 Baby AT Mainboard AWARD BIOS SETUP CPU Internal Cache External Cache default setting Enabled These fields allow you to turn on or turn off the Level 1 and Level 2 cache that built in Pentium II II or CeleronTM processors CPU L2 Cache ECC Checking default setting Enabled This option will enable or disable the ECC checking on the CPU L2 cache The ECC checking will ensure the accuracy of the data stored on the L2 cache Quick Power on Self Test default setting Enabled The Quick Power On Self Test will skip some test and speed up the boot process If you find the system is working normally you can always enable this feature so that you don t have to wait too long on the POST First Second Third Boot Device
16. select Auto to enable BIOS support The Choice Auto Disabled USB Controller Default setting Enabled This field allows you to enable or disable the onboard USB controller USB Keyboard Support Default setting Disabled If you re installing a USB keyboard please select Enable in this field Otherwise use the default setting Init AGP Display First Default setting PCI slot When you have both the onboard AGP and PCI VGA card installed in the system you can use this field to decide the display priority Onboard the display will be active on the onboard VGA adapter PCI slot The display will be active on the PCI VGA adapter AC97 Audio Default setting Auto There is the Audio interface built in the system chipset You can use this field to configure the onboard Audio interface or disable the audio interface The choice Auto Disable AC97 Modem Default setting Auto There is the AMR interface built on the mainboard If you have the AMR modem card installed in the PC system please select Auto If you do not have the modem card installed in the PC system or you are using the PCI modem please select Disabled IDE HDD Block Mode Default setting Enabled This selection allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive HDD Enabled IDE controller uses block mode Disabled IDE controller uses standard mode 4 10
17. as shown in figure Fig 4 2 will be triggered 4 1 Intel810 Baby AT Mainboard AWARD BIOS SETUP 4 2 MAIN MENU CMOS Setup Utility Copyright C 1984 1999 Award Software Frequency Voltage Control Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password Power Management Setup Save amp Exit Setup PNP PCI Configuration Exit Without Saving PC Health Status ESC Quit i Select Item F10 Save amp Exit Setup Time Date Hard Disk Type Fig 4 2 CMOS SETUP MAIN MENU SCREEN You can not see this selection field when W83627F is installed on the mainboard 4 33 CONTROL KEYS Listed below is the explanation of the keys displayed at the bottom of the screens which will be used in the CMOS SETUP program Arrow Keys Use the arrow keys to move the cursor to the desired item Enter Select the desired item F1 Display the help screen for the selected feature ESC Exitto the previous screen PgUp PgDn To modify or change the content of the highlighted item F5 Retrieves the previous value from CMOS data only the current page setup will be retrieved F7 Loads the SETUP default values from BIOS default table only the current page setup will be loaded F10 Saveall changes to CMOS RAM from the MAIN MENU Intel810 Baby AT Mainboard AWARD BIOS SETUP 4 4 STANDARD CMOS FEATURES CMOS Setup Utility
18. system Why AIR Bus One of the most significant and immediate feature from AIR bus is it will rescue your system BIOS from virus attack There was a virus called CIH virus and it made users start to aware that the virus could also make serious damage to the mainboard Such virus will kill the system BIOS and make PC system failed to work Unfortunately similar virus will become popular and the protection to the mainboard will be surely necessary and extremely important Everyone can see that the PC system will be failed to boot when the system BIOS is destroyed There is no perfect prevention for such virus attack because there is always the new virus invented However AIR Bus can be one of the best solution to rescue your PC system from virus attack because it is an intelligent interface and it will restore the system BIOS automatically In case that the PC system is infected by virus and the system BIOS is destroyed users have to call for help or send the PC system to the dealer for trouble shooting However you do have to wait for such technical support because the AIR Bus will have the system BIOS get recovered within a single minute The recovery procedure is done automatically and you do not have to make any hardware or software setting Simply plug in KEYBIOS TM and click on the power button and then leave everything done by KEYBIOS Besides the KEYBIOS can be used as a spare copy of the system BIOS No mat
19. system DMA channel a type depending on the type of device using the DM channel Memory Resources Default setting Press Enter This sub menu can let you control the memory resource Assign IRQ For VGA USB Default setting Enabled The system s IRQ signals are limited and sometimes you may feel like to some more IRQ signals for your add on cards The system BIOS allows you to disable the IRQ which is supposed to be connected to VGA and USB ports When you have choose to disable the IRQ on VGA or USB port the IRQ on the related IRQ will be released and becomes available for other devices Before you decide to proceed with the change please make sure that you do not have USB and VGA adapter which will use the IRQ signal Otherwise your PC system will become abnormal and the devices connected to these ports may not be working at all It is very simple to tell the difference If you are going to disable the IRQ on the USB port check whether is any device connected to the USB port If you can not find any device you may feel free to disable the IRQ on the USB port and have the IRQ used by other device As for VGA adapter it will be a little difficult You may try to find whether your VGA card requires the IRQ signal or not If you can not find the information from the user s manual of your VGA card You may use the following information to make your choice 1 Most VGA cards do not need to have the IRQ signal 2 If you can n
20. this setting unless you are the technician Please refer to the following for functional description speed of CPU clock force your CPU to use that clock toggle switch CPU FSB CLOCK SW 1 SW 2 SW 3 SW 4 Auto ON OFF OFF ON 66MHz OFF ON ON OFF 100MHz OFF OFF ON OFF Note 1 SW will have no function unless Default is selected in the CPU Host SDRAM Clock selection field in the BIOS setup program refer to Section 4 11 Please do not to make jumper setting on SWI unless you are the professional technician 2 When Default is selected you may use SW to select different speed instead of letting the system BIOS to select the CPU clock automatically 3 23 Intel810 Baby AT Mainboard HARDWARE SETUP 3 5 INSTALLATION OF DEVICE DRIVERS There is a CD which comes with the mainboard The CD contains the device drivers which is necessary when installing the mainboard Please refer to the following procedures to install the device drivers 1 When you have install the operation system you will have to install some device driver of the mainboard so that it will work normall
21. 10 IDE 2 Connectors Secondary IDE Port 170H IRQ 15 CN10 IDE 2 CN9 SB Link is designed for PCI sound cards such as CreativeTM EMU8008 sound chip Intel810 Baby AT Mainboard HARDWARE SETUP 3 3 13 CN12 IR CIR Infrared Rays Connector Consumer IR IR INFRARED RAYS CONNECTOR Pin Assignment of IR port 45VDC NO CONNECTION 2 IRRECEIVE 3 GROUND 4 IR TRANSMIT 5 Pin Assignment of Consumer IR 6 NOCONNECTION O 7 CONSUMER IR RECEIVE o 8 SV STANDBY O 9 NOCONNECTION 10 Intel810 Baby AT Mainboard HARDW
22. 10 Baby AT Mainboard AWARD BIOS SETUP 4 S POWER MANAGEMENT SETUP CMOS Setup Utility Copyright C 1984 1999 Award Software Power Management Setup ACPI Function Disabled Item Help ACPI Suspend Type S1 POS Power Management User Define Menu Level gt Video Off Method Blank Screen Video Off In Suspend Yes Suspend Type Stop Grant Modem Use IRQ 3 Suspend Mode Disabled HDD Power Down Disabled Soft Offby PWR BTTN Instant off Wake Up by PCI card Disabled Power on by Ring LAN Disabled CPU Thermal Throttling 50 0 Resume by Alarm Disabled x Date of Month Alarm 0 x TIME HH MM SS ALARM 0 0 0 Reload Global Timer Events Primary IDE 0 Disabled Primary IDE 1 Disabled Secondary IDE 0 Disabled Secondary IDE 1 Disabled FDD COM LPT Port Disabled PCI PIRQ A D Disabled ACPI function Default setting Disabled When Enabled the PC system will have the ACPI function However if you want to use the ACPI function you have to use the most updated operation system like Windows 98 When installing Windows 98 you will have to give some specific parameter so that the ACPI function will be installed into your PC system please refer to the manual of Windows 98 for the parameters When the ACPI function is installed in your PC system successfully you will find the ACPI function in the power management icon The PW switch mentioned in Section 3 defined by the ACPI
23. 2 HARDWARE MONITORING optional When Winbond W83627HF please refer to U12 on page 1 2 is installed on the board it will monitor hardware healthy status such as system voltage system temperature and cooling fans When the CPU temperature is too high the system BIOS will tell the system board to give a series of beeping alarm and slow down the CPU speed throttling speed so that you can take proper action to prevent your system from damage When you hear the beeping alarm turn the power off and check on the mainboard components to see whether it is working properly or not If you don t know how to handle it send the PC system to your dealer for technical support There is the hardware monitoring program in the CD which comes with this mainboard You can run the hardware monitoring program and then it will monitor the system healthy status all the time DIMENSION 4 layers PCB 240mm x 220mm Baby AT Form Factor OPERATION SYSTEM This mainboard is compatible with the operation system such as MS DOS WindowsNT OS 2 NOVELL Windows 95 Windows 98 etc Intel810 Baby AT Mainboard INTSTALLATION 2 INSTALLATION 2 1 UNPACKING The mainboard contains the following components Please inspect the following contents and confirm that everything is there in the package If anything is missing or damaged call your supplier for instructions before proceeding This mainboard CPU Booster module optional One USER S MANUAL
24. 24 PUSH BUTTONS AND LED CONNECTORS 3 14 3 3 25 SPEAKER AND KEY LOCK CONNECTOR 3 17 1 Intel 810 Baby AT Mainboard 3 4 JUMPER SETTINGS 3 18 3 5 INSTALLATION OF DEVICE DRIVERS 3 24 4 AWARD BIOS SETUP oet euo eo Eie tide 4 1 GETTING STARTED ch issis 4 1 42 MAIN MENU ese qp aee aeta epu reach aerae 4 2 48 CONTROL KEYS aderisce ooi onto nhat ad 4 2 44 STANDARD CMOS FEATURES 4 3 4 5 ADVANCED BIOS FEA TURES 4 4 46 ADVANCED CHIPSET FEATURES 4 7 4 7 INTEGRATED PERIPHERALS 4 9 4 8 POWER MANAGEMENT SETUP 4 13 49 PNP PCI CONFIGURATIONS 4 17 4 10 PC HEALTH SPA 4 19 411 FREQUENCY VOLTAGE CONTROLLI 4 20 4 12 LOAD OPTIMIZED DEFAULTS 4 21 4 13 SET SUPERVISOR PASSWORD 4 22 4 14 SET USER PASSWORDLD
25. 810DTC S10DT Pentium Celeron Twin Processor AT MAINBOARD VER 3 x USER S MANUAL OC NO UM 810DTC E2 PRINTED IN TAIWAN Intel810 Baby AT Mainboard TABLE OF CONTENTS TABLE OF CONTENTS CHAPTER amp SECTION Page 1 INTRODUCTION rS 1 1 LI OVERVIEW ii I I tues A I uwa 1 1 1 2 AIR BUS ese S sesuscsnusensendvactonss EDU ea xv RIF SUE Seo ERE DOE 1 2 13 CPU BOOSTER qutm 1 3 1 4 MAINBOARD LAYOUI A 1 4 1 5 SPECIFICATIONS 1 5 15 INSTALLATION emeret u N sass q 2 1 AJ UNPACKING eite er rice uec I dei EE 2 1 2 2 ACPI FUNCTION Iy A 2 2 2 3 POWER OFF THE PC SYSTELMA 2 3 HARDWARE 8 3 1 3 1 INSTALLATION OE CRU 3 1 3 2 INSTALLING THE DRAM MODULES 3 2 3 3 CONNECTORS ES GR UI Q ai e iue RUE 3 3 33 1 BATI BATTERY SOCKET 3 3 3 3 20 CN1 KEYBOARD CONNECTOR 3 3 3 333 CN2 PS 2 MOUSE CONNECTOR 3 4 3 334 CN3 SERIAL PORT COM 1
26. ARE SETUP 3 3 14 CN13 CPU Cooling Fan Power Connector FAN1 The CPU cooling fan power connector can be connected to the CPU cooling fan so that it will cool down the CPU temperature GND 12V Fan Signal 3 3 15 CN14 AT Power Connector CN14 Intel810 Baby AT Mainboard HARDWARE SETUP 3 3 16 CN15 ATX Power Connector CN15 ATX Power connector 3 3 17 CN16 WOL Wake On LAN Connector In order to use the WOL LAN card to trigger the power of the PC system the switching power supply must be able to provide at least 800mA current driving ability on 5V standby voltage 5V Standby Ground WOL Signal It
27. CONNECTOR 3 4 3 3 5 SERIAL PORT COM 2 CONNECTOR 3 5 3 3 6 CN5 PARALLEL PORT CONNECTOR 3 5 3 3 7 CN6 USB PORT 1 CONNECTOR 3 6 3 3 8 CN7 USB PORT 2 CONNECTOR 3 6 3 3 CN8 FLOPPY DISK CONTROL PORT 3 6 3 3 10 CN9 IDE 1 CONNECTORS 3 7 3 3 11 CN10 CONNECTORS 3 7 3 3 12 CN11 SB LINK CONNECTOR 3 7 3 3 13 CNI2 IR CIR CONNECTOR 3 8 3 3 14 CN13 CPU COOLING FAN FAN I 3 9 3 3 15 CN14 AT POWER CONNECTOR 3 9 3 3 16 CN15 ATX POWER CONNECTONR 3 10 3 3 17 CN16 WOL CONNECTOR 3 10 3 3 18 CN17 CHASSIS FAN POWER CONNECTOR 3 11 3 3 19 CN18 AUDIO GAME CONNECTOR 3 11 3 3 20 CN19 VGA CONNECTOR 3 12 3 3 21 CN21 CN22 CD IN CONNECTOR 3 13 3 3 22 CN23 TV OUT CONNECTOR 3 13 3 3 23 CN25 AIR BUS CONNECTOR 3 14 3 3
28. Electricity may cause damage to the components on the mainboard In order to avoid the damage to the mainboard accidentally please discharge all static electricity from your body before touching this mainboard NOTICE Information presented in this manual has been carefully checked for reliability however no responsibility is assumed for inaccuracies The information contained in this manual is subject to change without notice iii Intel810 Baby AT Mainboard INTRODUCTION 1 INTRODUCTION 1 1 OVERVIEW This Mainboard is a high performance personal computer mainboard It is the baby AT form factor with both Slot 1 optional and Socket 370 designed on the board for different type of CPU package The Intel 1810 chipset is chosen as the core logic of the mainboard to give the most outstanding performance and reliability It is designed for 233 266 300 333 350 366 400 433 450 466 500 550 600MHz and higher speed Penttum and Celeron processors This mainboard has built in two channels of PIO and Ultra DMA33 66 Bus Master mode PCI IDE ports to connect the modern IDE devices In addition one Floppy Disk control port two high speed Serial ports UARTs one multi mode Parallel port One PS 2 mouse port one IR interface and two USB ports are designed on the board There are the 3D PCI audio and AGP VGA interfaces built on the board These onboard interfaces are the PnP devices Plug and Play and they
29. Halt On This selection field allows you to decide whether the PC system will halt when the system board detects any error during Power On Self Test 4 3 Intel810 Baby AT Mainboard AWARD BIOS SETUP 4 5 ADVANCED BIOS FEATURES CMOS Setup Utility Copyright C 1984 1999 Award Software Advanced BIOS Features Virus Warning Disabled Item Help CPU Internal Cache Enabled External Cache Enabled Menu Level CPU L2 Cache ECC Checking Enabled Quick Power On Self Test Enabled Allows you to choose First Boot Device Floppy The Virus warning Second Boot Device HDD 0 Feature for IDE Hard Third Boot Device LS ZIP Disk boot sector Boot Other Device Enabled Protection If this Swap Floppy Drive Disabled Function is enabled Boot Up Floppy Seek Enabled And some attempt to Boot Up NumLock Status On Write data into this Gate A20 Option Fast Area BIOS will show a Typematic Rate Setting Disabled Warning message on Typematic Rate Chars Sec 6 Screen and alarm beep Typematic Delay Msec 250 Security Option Setup PS 2 mouse function control Enable OS Select For DRAM gt 64MB Non OS2 HDD S M A R T Capability Disabled Report No FDD For Win95 No C8000 CBFFF Shadow Disabled CC000 CFFFF Shadow Disabled D0000 D3FFF Shadow Disabled D4000 D7FFF Shadow Disabled D8000 DBFFF Shadow Disabled DC000 DFFFF Shadow Disabled Virus Warning In order to avoid virus infection happens on your PC system
30. I 3 3 20 CN19 VGA Connector VGA Adapter The VGA connector on the board is the AGP VGA interface and you can use an adapter as shown in the above picture to connect it to your VGA monitor 3 12 Intel810 Baby AT Mainboard HARDWARE SETUP 3 3 21 CN21 CN22 CD IN Connector The CD IN connectors on the board can be used to connect to the CD ROM audio out There are two different type of connectors for CD ROM audio out connector Audio R 2 GND 35 Audio L 4 GND Jt Note Audio L Left channel audio out Audio R Right channel audio out GND Audio Ground 3 3 22 CN23 TV OUT Connector optional There is the TV OUT interface designed on the mainboard A TV convert board can be installed on the interface and you may connect your PC system to a TV CN23 TV OUT CONNECTOR
31. Security Option setup in Section 4 5 When Setup is selected in Security Option If you want to change the BIOS setting you will have to key in the Supervisor Password so that you can start the BIOS setup program and change the system setting When System is selected in Security Option When turn on the PC system it will request you to enter the Password Without the correct password the PC system will stop and the operation system will not be loaded 4 22 Intel810 Baby AT Mainboard AWARD BIOS SETUP 4 14 SET USER PASSWORD CMOS Setup Utility Copyright C 1984 1999 Award Software Standard CMOS Features Frequency Voltage Control Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Power Management Setup Save amp Exit Setup PNP PCI Configuration Exit Without Saving PC Health Status ESC Quit 1 lt Select Item 10 Save amp Exit Setup Time Date Hard Disk Type The User Password can be used to check the user s authority However this password entry is somewhat different to the SUPERVISOR PASSWORD mentioned in previous page The User Password will have different function according to the Supervisor Password and the Security Option setup in Section 4 5 A When there is the password stored in the SUPERVISOR PASSWORD 1 When Setup is selected in Security Option When you u
32. al LPT port name and matching address for the physical parallel printer port The choice 378H IRQ7 278H IRQ5 3BCH IRQ7 Disabled ECP Mode Use DMA Default setting 3 The Parallel port on the mainboard support ECP EPP ECP EPP and SPP modes When you select ECP mode you may specify the DMA for the parallel port so that it will support ECP mode properly 4 11 Intel810 Baby AT Mainboard AWARD BIOS SETUP PWRON After PWE Fail Default setting When you select Off in this field the system will not be powered on whenever there is the power failure occurs When you are using the ATX type power supply you may select Former Sts in this field and the PC system will refer the previous status and then decide whether to powered on the PC system or not For example if the PC system was on before the power failure occurs then the PC system will be powered on automatically when the power system back to normal If the PC system was under the power off status then it will remain power off power failure The choice off Former state Game Port Address Default setting 201 This field allows you to select the I O address for the onboard Game port Midi Port Address Default setting 330 This field allows you to select the I O address for the onboard Midi port Midi Port IRQ Default setting 10 This field allows you to select the IRQ for the onboard Midi port 4 12 Intel8
33. amp KBLOCK CONNECTORS PIN ASSIGNMENT OF SPK CONNECTOR Pin Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Signal Name 5VDC N C NC SPK Signal N C PIN ASSIGNMENT OF PWR LED amp KBLOCK CONNECTOR Pin Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Signal 5V Pull up GND GND KB Signal GND 3 17 Intel810 Baby AT Mainboard HARDWARE SETUP 3 4 JUMPER SETTINGS This section will discuss the jumper setting on the mainboard In order to let you have better idea of the Jumper setting please see below for the explanation of jumper settings before you start this section oen c gt 00 000 show gt 1 1 1 21000 1 1 The following jumpers which labeled with optional means they are the optional choice for customers and the related components are normally not populated on the mainboard In order to make the mainboard works properly in your PC system please make sure all jumper settings are at correct before installing this mainboard A jumper is a set of two three or more jumper pins which allows users to make different system configuration by putting the plastic connector plug mini jumper on it The jumper setting is necessary when installing different components onto the mainboard A JP1 Keyboard and PS 2 Mouse OnNow function selection The Keyboard and PS 2 Mouse OnNow function is designed on the mainboard and you can use keyboard and mouse key cli
34. are fully compatible with the Windows environment So you don t have to purchase another sound card or VGA card because they are integrated on the mainboard Pentium II Pentium M III and Celeron are the 32 bit processors with RISC technology which offers several key features such as built in 512K 256K 128K L2 cache 12 stage super pipeline architecture out of order execution etc In order to optimize of its capabilities and performances the 32 bit Operating System such as Windows 95 Windows 98 Windows NT and OS 2 etc and 32 bit applications are recommended The 810 chipset is designed to support the 66MHz and 100MHz Front Side Bus FSB CPUs There is the CPU booster which comes with the 810DT and it will allow you to install 133MHz FSB Pentium III processor on the socket 370 connector and deliver the performance of PC 133 architecture Please refer to the following picture for the outlook of the CPU booster Sur Good toed n me cem t tA t est sm e Puis 4 Install the CPU booster Slot I allows to use the 133MHz FSB CPU on socket 370 and it will increase the system performance 1 1 Intel810 Baby AT Mainboard INTRODUCTION 1 2 AIR BUS There is a revolutionary new interface designed on the mainboard the AIR Bus CN25 There is the KEYBIOS device is designed to connect to the AIR Bus and it will give you lots of incredible features to your PC
35. ave to install the External modem to your PC system and tell the PC system which serial port connects to the modem by selecting the IRQ in this field officially COM 1 uses IRQ4 and COM 2 uses IRQ3 Suspend Mode Default setting Disabled This field allows you to choose the time interval which PC system will turn into suspend mode The choice Disabled 1 2 4 8 12 20 30 40 Min and 1Hr HDD Power Down Default setting Disabled When enabled and after the set time of system inactivity the hard disk drive will be powered down while all other devices remain active Soft Off by PWR BTTN Default setting Instant off This field allows user to define the feature of the PW connector it is used to connect the power button The setting can be either Delay 4 Sec or Instant Off Please refer to page 3 16 for details of function description 4 15 Intel810 Baby AT Mainboard AWARD BIOS SETUP Wake Up by PCI Card Default setting Disabled This field allows you to enable disable the PCI wake up feature There is some PCI interface card which support the wake up function and it will wake up the PC system from the power off state Power by Ring LAN Default setting Disabled When Enabled you can use the Modem Ring signal or the LAN wake up signal to power on the PC system CPU Thermal Throttling Default setting 50 0 This mainboard support the hardwar
36. cks to power on the PC system However there may have some keyboard and mouse are not compatible with the OnNow function In this case please use JP1 to disable the OnNow function Pinl amp Pin 2 Short OnNow Disabled Pin 2 amp Pin 3 Short OnNow Enabled L Intel810 Baby AT Mainboard HARDWARE SETUP B JP2 CPU Voltage Range Selection JP2 is designed on the mainboard which allows you to select the CPU core voltage range Vcore to protect the CPU The voltage regulator on the mainboard will generate 1 3V 3 5V DC to support different processors Basically most mainboards will use the CPU VID signal VID0 VID4 from the CPU to decide the proper CPU core voltage Vcore In case that there is the poor connection between CPU and its socket or uninstall the CPU from the mainboard while the system power is ON Under such circumstance mainboard may receive wrong VID signal and send wrong Vcore to the CPU Unfortunately wrong Vcore may destroy the CPU and the mainboard JP2 is designed to control the Vcore within the safe range so that it won t make any damage to the CPU or mainbord because of wrong VID signal Since m
37. e Modem ring in Phone ring in LAN signal etc 3 One LED LED1 onboard to indicate the S5 status Soft Off status WOL PORTS One WOL connector supports Wake On LAN WOL up designed SB LINK PORTS Optional One SB LINK feature connector to support PCI sound cards such as CreativeTM Labs EMU8008 sound chip USB PORTS Two Universal Serial Bus USB ports IDE PORTS Two channels of Ultra DMA33 66 Bus Master IDE ports which will support up to 4 IDE devices like IDE hard disk ATAPI CD ROM and LS 120 ZIP 100 devices The IDE ports can be programmed to support PIO Mode 4 DMA mode 2 and Ultra DMA 33 66 SUPER I O PORTS 1 One PS 2 Mouse connector and One AT type Keyboard connector 2 Two high speed NS16C550 compatible serial ports UARTS 3 One SPP EPP ECP mode Bi directional parallel port 4 One Floppy Disk Control port 4 One HP SIR SHARP IR compatible IR port Consumer Remote Control supports RC 5 RC 6 NEC RCA and RECS 80 When W83627HF is installed on the board it supports hardware monitoring 6 One digital Game and MIDI compatible with MPU 401 UART mode port 3D SOUND AC97 audio interface is designed on board for 3D Sound Effect TV OUT OPTIONAL One TV OUT connector and daughter board optional for TV display requirement 1 6 Intel810 Baby AT Mainboard INTRODUCTION COOLING FAN CONNECTOR One CPU cooling Fan Connectors on the board FAN1 One Chassis cooling Fan Connectors on the board FAN
38. e JP7 to clear the keyboard as shown below 1 3 2 1 2 Short Normal Setting 1 2 3 2 3 Short Clear Password Please use the following procedure to clear the CMOS password 1 Unplug the AC power cable from the PC system 2 Put the mini jumper on pin 2 3 of JP7 around 3 to 5 seconds and then return it to the original position pin 1 2 3 Re connect the AC power cable 3 21 Intel810 Baby AT Mainboard HARDWARE SETUP 3 22 Intel810 Baby AT Mainboard HARDWARE SETUP E SW FSB Clock Selection SW is designed on the board to choose the CPU FSB clock Front Side Bus Clock for some special purpose Basically you don t have to worry about the FSB clock because it will be detected by the mainboard automatically When you have installed the CPU onto the mainboard this mainboard will detect the CPU type and specify the proper FSB clock for the CPU So you need not to make any setting to select the FSB clock However sometimes you may feel like to select different FSB clock for some special purpose In this case you may use the BIOS setting to select different FSB clock or use the switch setting on SW to force your CPU to use the selected FSB clock Please do not attempt to change
39. e monitoring feature You may use this field to select the CPU speed when the mainboard detects the CPU temperature is too high so that it will provide better protection to the mainboard and CPU Resume by Alarm Default setting Disabled When Enabled you can use the following two selection fields Date of Month Alarm and Time hh mm ss Alarm to select the alarm date and time You can use these two fields to set the date and time which you want to resume the system from Sleep or Suspend mode The Time must be set in a 24 hour format Reload Global Timer Events When Enabled an event occurring on each device listed below restarts the global time for Standby mode Primary IDE 0 Primary IDE 1 Secondary IDE 0 Secondary IDE 1 FDD COM LPT Port PCI PIRQ A D 4 16 Intel810 Baby AT Mainboard AWARD BIOS SETUP 4 9 PNP PCI CONFIGURATIONS CMOS Setup Utility Copyright C 1984 1999 Award Software PnP PCI Configuration PnP OS Installed No Item Help Reset Configuration Data Disabled Resources Controlled By Auto ESCD Menu Level gt IRQ Resources Press Enter DMA Resources Press Enter Select yes if you are Memory Resources Press Enter Using a plug and play Capable operating system Select no if PCI VGA Palette Snoop Disabled you need the bios to Assign IRQ For VGA Enabled configure non boot Assign IRQ for USB Enabled device Reset Configuration Data Nor
40. ed allows caching of the system BIOS ROM at F000h FFFFFh resulting in better system performance However if any program writes to this memory area a system error may result Enabled BIOS access cached Disabled BIOS access not cached Video BIOS Cacheable default setting Disabled Selecting Enabled allows caching of the video BIOS ROM at C0000h to C7FFFh resulting in better video performance However if any program writes to this memory area a system error may result Enabled Video BIOS RAM access cached Disabled Video BIOS RAM access not cached Intel810 Baby AT Mainboard AWARD BIOS SETUP Memory Hole At 15M 16M default setting Disabled In order to improve performance certain space in memory can be reserved for ISA cards Such memory must be mapped into the memory space below 16 MB Enabled Memory hole supported Disabled Memory hole not supported Delayed Transaction default setting Enabled The chipset has an embedded 32 bit posted write buffer to support delay transactions cycles Select Enabled to support compliance with PCI specification version 2 1 The Choice Enabled Disabled On Chip Video Window Size default setting 64MB This mainboard provides the most DVMT technology Dynamic Video Memory Technology and it will increase the video display performance There is the AGP VGA interface on this mainboard and the AGP display card will use some of the s
41. er to Section 4 8 for BIOS setup Q If the setup in CMOS is Delay 4 Sec the function of PW will be A When system power is OFF Press the PW switch the system will be powered on B When system power is ON a The system is in Full ON mode a 1 Click on this switch less than 4 seconds the system will be turned into Suspend mode the GREEN mode a 2 Press and hold this switch for more than 4 seconds the system will be powered off b When the system is in Suspend mode b 1 Click on this switch less than 4 seconds the system will return to Full ON mode b 2 Press and hold this switch more than 4 seconds the system will be powered off The setup in CMOS is Instant off A When system power is off Click on this switch the system will be powered on B When system power is on Click on this switch the system will be powered off instantly 3 16 Intel810 Baby AT Mainboard HARDWARE SETUP 3 3 25 Speaker and Key Lock connector The connectors shown in the following picture will be connected to the speaker Keyboard Lock and Power LED connector on the chassis DOO O s CD 354 S Pwn LED amp KBLOCK SPK
42. hardware monitoring feature on the board you can install the hardware monitoring software included in the CD disc and you can use the hardware monitoring feature to check the mainboard healthy status Beside the hardware monitoring software program you can also use the BIOS setup screen to check the hardware status The table above gives you another choice to monitor the mainboard healthy status beside the hardware monitoring software Please select the PC HEALTH STATUS and you will see the table as shown above and that you can check on the related field and monitor the status like voltage Temperature and cooling fan rotation speed etc 4 19 Intel810 Baby AT Mainboard AWARD BIOS SETUP 4 11 FREQUENCY VOLTAGE CONTROL CMOS Setup Utility Copyright C 1984 1999 Award Software Frequency Voltage Control Auto Detect DIMM PCI Clk Enabled Item Help Spread Spectrum Disabled CPU Host SDRAM Clock Default Menu Level gt CPU Clock Ratio X 3 5 i Auto Detect DIMM PCI CIk default setting Enable When Enabled is selected the mainboard will detect the presence of devices on DIMM and PCI slots When there is no device presented on some of the PCI or DIMM connector the clock on the related DIMM and PCI slot will be disabled to reduce the Electro Magnetic Interference EMI Spread Spectrum default setting Disabled This field allows you to reduce the system EMI radiation When you se
43. ing at 133MHz and the system performance will be increased instantly When CPU booster is installed it will provide the following features 1 810 mainboard will be able to support 133MHz FSB Pentium III processors 2 The memory architecture will be changed from PC 100 to PC 133 INSTALLATION OF CPU BOOSTER When the CPU booster installed onto the slot 1 connector it will fine tune the mainboard coupling interface so that you can use 133MHz FSB CPU Please refer to the following picture for the outlook of the CPU booster 7 Ses C cred bend SG bend wong reed me cem er Gr t nt dm cm In order to make the CPU booster working normally please refer to the following notice when use CPU booster to increase the performance 1 The Slot 1 connector supports only 66 100MHz FSB CPUs 2 When CPU booster is not installed on the mainboard you can install either 66MHz or 100MHz FSB CPU onto the Socket 370 3 When CPU booster is installed on the Slot 1 you can install 133MHz FSB CPU on to the Socket 370 connector 4 Always use PC 133 DIMM module when CPU booster is installed and refer to the following to install the DIMM module DIMMI DIMM2 Single bank Single bank OK Single bank Double bank OK Double bank Single bank OK Double bank Double bank May failed 1 3 Intel810 Baby AT Mainboard INTRODUCTION 1 4 MAINBOARD LAYOUT Mainboard Layout with Quick Installation CN12 IR Por
44. is different to the BIOS setup and it always has the higher priority than what was defined in the system BIOS 4 13 Intel810 Baby AT Mainboard AWARD BIOS SETUP According to what was defined by the ACPI in Windows 98 the PW switch can be either the Standby switch or shutdown switch When Standby switch is selected the first click on the PW switch will have the PC system turn into standby mode If you want to wake up the PC system you will have to use the devices such as keyboard mouse etc which is specified in the Windows 98 ACPI function to trigger the PC system so that it will be back to full on mode For more detail of ACPI function please refer to Windows 98 user s manual for more detail information ACPI Suspend Default setting 51 POS This field allows you to select the mode of suspend state When 51 is selected The CPU perform a Stop Grant cycle and halt its instruction stream during the S1 suspend state In other word the CPU is in the sleep status Power Management Default setting User Define This category allows you to select the type or degree of power saving and is directly related to the following modes 1 Doze Mode 2 Standby Mode 3 Suspend Mode 4 HDD Power Down Disable default No power management Disables all four modes Minimum power management Doze Mode 1 hr Min Power Saving Standby Mode 1 hr Suspend Mode 1 hr and HDD Power Down 15 min Maxi
45. k Type Save amp Exit Setup This option will save all setup values to CMOS RAM amp EXIT SETUP routine Move the selection bar to SAVE amp EXIT SETUP and pressing Enter key then types Y and Enter key the values will be saved and all the information will be stored in the CMOS memory and then the setup program will be terminated and the system will start to reboot Exit Without Saving This item exit the setup routine without saving any changed values to CMOS RAM When you do not want to save your change to the CMOS memory you may choose to run this option and the setting what you made in the BIOS setup routine will be given away Move the selection bar to EXIT WITHOUT SAVING and click on the Enter key then you will be asked to confirm the action to exit press the Y and Enter key the setup program will be terminated and the system will start to reboot 4 24 Intel810 Baby AT Mainboard UPDATE THE SYSTEM BIOS 5 UPDATE THE SYSTEM BIOS Why BIOS update There are always the new CPU and devices introduced to the market and you may have to get the system BIOS updated so that the mainboard will work with the new device properly Before we start to discuss how to upgrade the system BIOS there are sever important issues which you may have to know before you can start to upgrade the system BIOS 1 Never try to interrupt the PC system during the BIOS
46. k floppy diskette and put it into the floppy disc drive 3 Key in the following DOS command to generate a diskette which you can use it to boot up your PC system afterward FORMAT A S 4 Copy the files which you downloaded from the web page as what was mentioned in STEPI STEP 3 START THE BIOS UPDATE PROCEDURE 1 Restart the PC system and get the PC system ready under the DOS prompt you may have to change the BIOS so that the PC system will boot from floppy drive 2 Run the following command under the DOS prompt gt AWDFLASH EXE 810DW BIN 3 When you see the display Do you want to save BIOS you may select Y and the program will make a backup copy of the system BIOS from your mainboard 4 If you do not want to make the backup copy of the system BIOS simply click the N key and then click the ENTER key 5 The PC system will ask whether you want to start the BIOS update procedure If you are sure everything is fine then click on the Y key to start the BIOS update you may stop here to terminate the BIOS update operation 6 The message Programming Flash Memory will be display on the screen to indicate the system BIOS is updating from now on you have to wait till the operation is finished Please do not terminate the operation 7 When the BIOS updating is finished you will see the message displayed on the screen RESET SYSTEM OR POWER OFF TO ACCOMPLISH UPDATE 5 2 Intel810 Baby AT Mainb
47. lect default the mainboard will decide whether to enable the Spread Spectrum or not When Spread Spectrum is enabled the special feature designed in the system chipset will be triggered and reduce the EMI as mentioned in the previous field CPU Host SDRAM Clock default setting Default This field allows you to select the CPU and SDRAM clock speed In order to optimize the system performance you need to select the CPU and SDRAM clock properly If you do not know how to select the parameter you may choose the Default setting and let the mainboard decide the parameter for you CPU Clock Ratio default setting X 3 5 This field allows to select the CPU clock ratio Basically most CPU clock ratio is fixed inside the CPU and user can not change it In this case the setting in this field will make no change to the default CPU clock ratio because it is decided by the CPU automatically 4 20 Intel810 Baby AT Mainboard AWARD BIOS SETUP 412 LOAD OPTIMIZED DEFAULTS CMOS Setup Utility Copyright C 1984 1999 Award Software Standard CMOS Features Frequency Voltage Control Advanced BIOS Features Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password Power Management Setup Save amp Exit Setup PNP PCI Configuration Exit Without Saving PC Health Status ESC Quit 11 lt Select Item F10 Save amp Exit Setup Time Date Hard Disk Type
48. ll support all kind of Pentium and Celeron processors from 233 MHz up 10 800 MHz CPU VCC Switching Voltage Regulator circuits onboard supports 1 30V DC through 3 5V DC CPU Core Voltage auto detected by the CPU WORD SIZE Data Path 8 bit 16 bit 32 bit 64 bit Address Path 32 bit PC SYSTEM CHIPSET Intel 1810 chipset 82810 82801AA 82802AB SUPER I O CHIPSET Winbond W83627F or W83627HF I O chip W83627HF supports Hardware monitoring FRONT SIDE BUS FREQUENCY 66 MHz 100MHz selectable When CPU booster is installed it will support 133MHz Front Side Bus frequency MEMORY There are two 168 pin DIMM sockets designed on the mainboard It supports 8MB up to 256MB use 16Mb 64Mb DRAM chip or 512MB use 128Mb DRAM chip BIOS AWARD System BIOS 4Mbit Flash ROM Supports Plug amp Play ACPI DMI and Green functions EXPANSION SLOTS AMR Slot One AMR slot for Modem Riser PCI Slots Four 32bit PCI slots 1 5 Intel810 Baby AT Mainboard INTRODUCTION ACPI FUNCTIOS PC99 COMPLIANT Advanced Configuration and Power Interface ACPI features are available on this mainboard It will let you have many additional features and that will make your PC system becomes very friendly and convenient Followings are the ACPI features designed on the board 1 Microsoft PC99 compliant fully supports 50 51 52 54 and S5 system operating status 2 System resumes by Panel switch Keyboard PS 2 Mous
49. ller Enabled USB Keyboard Support Disabled Init Display first PCI Slot AC97 Audio Auto AC97 Modem Auto IDE HDD Block Mode Enabled POWER ON Function BUTTON ONLY KB Power ON Password Enter Hot Key Power ON Password Ctrl F1 Onboard FDC Controller Enabled Onboard Serial Port 1 3F8 IRQ4 Onboard Serial Port 2 2F8 IRQ3 UART Mode Select Normal Onboard Parallel Port 378 IRQ7 Parallel Port Mode SPP EPP Mode Select EPP 1 7 ECP Mode Use DMA 3 PWRON After PWR Fail Off Game Port Address 201 Midi Port Address 330 Midi Port IRQ 10 On Chip Primary Secondary PCI IDE Default setting Enabled These options allow you to enable disable the onboard IDE interface IDE Primary Secondary Master Slave PIO Default setting Auto The four IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for each of the four IDE devices that the onboard IDE interface supports Modes 0 through 4 provide successively increased performance In Auto mode the system automatically determines the best mode for each device 4 9 Intel810 Baby AT Mainboard AWARD BIOS SETUP IDE Primary Secondary Master Slave UDMA Default setting Auto Ultra DMA 33 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver Windows 95 OSR2 or a third party IDE bus master driver If your hard drive and your system software both support Ultra DMA 33
50. mally you leave this field Disabled Select Enabled to reset Extended System Configuration Data ESCD when you exit Setup if you have installed a new add on and the system reconfiguration has caused such a serious conflict that the operating system can not boot Resources Controlled by Default setting Manual The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices However this capability means absolutely nothing unless you are using a Plug and Play operating system such as Windows 95 If you set this field to manual choose specific resources by going into each of the sub menu that follows this field a sub menu is preceded by a gt The choice Auto ESCD Manual PCI VGA Palette Snoop Default setting Disabled Some display cards are non standard VGA card such as graphics accelerator or MPEG Card which may not display color properly on your screen Enable the setting in this field may correct this problem Please leave it Disabled as the default setting shown above if you are using the normal display card 4 17 Intel810 Baby AT Mainboard AWARD BIOS SETUP IRQ Resources Default setting Press Enter When resources are controlled manually assign each system Interrupt a type depending on the type of device using the interrupt DMA Resources Default setting Press Enter When resources are controlled manually assign each
51. mum power management ONLY AVAILABLE Max Power Saving FOR SL CPU Doze Mode 1 min Standby Mode 1 min Suspend Mode 1 min and HDD Power Down 1 min Allows you to set each mode individually When not disabled each of the ranges are from 1 min to 1 hr except for HDD Power Down which ranges from 1 min to 15 min and disable User Defined 4 14 Intel810 Baby AT Mainboard AWARD BIOS SETUP Video Off Method Default setting Blank screen When you are using the Green Monitor with your PC system there are three modes selectable in this field to save the power energy This selection will cause the system to turn off the V H SYNC Blank vertical and horizontal synchronization ports and write blanks to the video buffer Blank Screen This option only writes blanks to the video buffer DPMS Initial display power management signaling Video Off In Suspend Default setting Yes When you select Yes the screen display will be disabled no display on the screen when the PC system is in the suspend mode Suspend Type Default setting Stop Grant This field allows to select the suspend type you can choose the CPU Stopy Grand Suspend or the PwrOn Suspend Modem Use IRQ Default setting 3 This mainboard has the ACPI feature designed on the board and it will wakeup automatically when it detects the incoming modem Ring in signal Before you can use the Ring in signal to wakeup your PC system you h
52. nce of the device driver is very important please follow the procedure above to install the related device driver 3 24 Intel810 Baby AT Mainboard AWARD BIOS SETUP 4 AWARD BIOS SETUP 4 1 GETTING STARTED When the system is first time powered on or reset by user the system BIOS will enter the POST routines Power On Self Test routines it will execute a series of diagnostics and system initialization and you will see the copyright message displayed on the screen In case that there is any error or malfunction detected the BIOS will give a series of beeping sound or display the error message on screen When the system is normal the screen display similar to figure Fig 4 1 will be displayed on the screen when the system is powered on Award Modular BIOS v4 51PG An Energy Star Ally 4 Copyright C 1984 99 Award Software Inc xxbodxx CPU at xxxMHz EPA POLLUTION PREVENTER Memory Test OK 1024K Shared Memory Award Plug and Play BIOS Extension v1 0A Copyright 1997 Award Software Inc Press DEL to enter SETUP ESC to skip memory test xx xx xx i810 xxx 6A69M 00 Fig 4 1 Initial Power On screen During the power on self testing POST the following message appears at the lower left corner of the screen Press DEL to enter SETUP To execute the Award amp BIOS CMOS Setup program please press the DEL key The CMOS SETUP MAIN MENU screen
53. ng messages automatically you need to have the software like Award Zero Volt Data Suspend Utility so that you can use the fax utility to receive the incoming fax message To enable the Modem Ring In feature you have to run the BIOS setup utility and enable the Power On by Ring LAN option please refer to Section 4 8 for the settings Note This function is not available when using the internal MODEM card O WAKE ON LAN WOL There is a WOL connector CN16 on the mainboard which is designed to connect to the signal from a LAN card which supports the Wake On LAN feature When such LAN card is installed you may turn on the PC system from the remote server and monitor the PC status To enable this feature you will have to use the BIOS setup utility to enable the Power On by Ring LAN in the BIOS setup program 2 3 POWER OFF THE PC SYSTEM There are two ways to power off the system They are Shut Down by Power Button and Shut Down by OS When you are using the ATX power supply you can choose the Shut Down from the file menu in the Windows operation system and the system will be powered off immediately 2 3 Intel810 Baby AT Mainboard HARDWARE SETUP 3 HARDWARE SETUP Before you can start to install this mainboard some hardware settings is required to make sure it will work perfectly with the devices which you are going to install in your PC system To configure the mainboard is a simple task only a few jum
54. oard UPDATE THE SYSTEM BIOS PROCESS Remove the floppy diskette from the floppy disk drive and then click on the F1 key to restart the PC system 8 If you found the PC system is restarting then it indicates that the BIOS update which you have made was successful 9 When the PC system is restarting click on the DEL key to trigger the BIOS setup program Select the Load Optimized Defaults to have the optimized parameter loaded into the system and then select the Standard CMOS Features to check whether the floppy disk drive is detected by the system BIOS correctly When finished select Save and Exit to save the change 10 When you have completed the procedure above all the BIOS update procedure is completed From now on you can use the new BIOS in your PC system Note In case that made some mistake and your PC system failed to work Please us the KEYBIOS to rescue the system BIOS The KEYBIOS is a new technology and it will rescue the system BIOS from all kind of damage 5 3
55. ost Pentium IVIII processors require the Vcore below 2 05V except few Pentium II processors So the default setting of JP2 will control the Vcore between 1 3V and 2 05V so that the CPU and mainboard will have a good protection Please do not change the setting on JP2 unless your CPU needs the voltage higher than 2 05V OPEN Vcore 1 3V 2 05V SHORT Vcore 1 3V 3 5V Note Please do not change the default setting on JP2 unless your CPU needs the voltage higher than 2 05V 3 19 Intel810 Baby AT Mainboard HARDWARE SETUP O JP4 CPU Voltage Adjustment optional The CPU voltage can be detected by the mainboard automatically JP4 is designed to make the CPU voltage a little bit higher than what is detected by the mainboard When select SHORT setting the CPU voltage will be 0 05V higher OPEN Vcore Default Setting JP4 SHORT Vcore will be 0 05V higher Note When you use
56. ot find the feature connector on your VGA card than it is quite possible that your VGA card does not need the IRQ signal 3 If your VGA card has the feature connector the VGA card but it has nothing connected to it In this case you still may have the IRQ disabled 4 If you have another add on card like video capture card which is connected to the feature connector on the VGA card In this case you can not disable the IRQ signal because the IRQ signal will be connected to the video capture card 4 18 Intel810 Baby AT Mainboard AWARD BIOS SETUP 4 10 PC HEALTH STATUS CMOS Setup Utility Copyright C 1984 1999 Award Software PC Health Status CPU Warning Temperature Disabled Item Help Current CPU1 Temperature 0 32 Current CPU2 Temperature 42 107 Menu Level gt Current CPUFANI Speed 3750 RPM Current CPUFAN2 Speed 0 RPM Current CPUFAN3 Speed 0 RPM Vcore 2 00 V 2 5V 2 49 V 3 3V 3 31 V 5V 4 97V 12V 11 91V 12V 11 54V VBAT V 3 02V 5VSB V 4 94V Shutdown Temperature Disabled This I O chip on the mainboard can be either the Winbond W83627F or W83627HF When W83627HF is installed on the board it will support the hardware monitoring feature and you will see the screen display shown above to indicate the system healthy status When the I O chip on the mainboard is W83627F you will not be able to see the above screen display because it does not support the hardware monitor function When there is the
57. pers connectors cables and sockets needs to be selected and configured please refer to page 1 3 to see the mainboard layout 3 1 INSTALLATION OF CPU There are two CPU sockets on the mainboard designed for Pentium II Pentium TM II and Celeron processors The CPU sockets on the mainboard are the Slot 1 optional and Socket 370 as shown in the following picture Socket 370 Note When CPU booster is installed on the mainboard It will make both CPU and the memory subsystem running at 133MHz instead of 100MHz and it will increase the system performance tremendously The CPU booster is the optional choice and it can be found in the 810DT The CPU booster provides the following features 3 The CPU booster will allow the 810 mainboard become able to support the 133MHz FSB Pentium III processors 4 The CPU booster will change the memory architecture of the 810 mainboard from PC 100 to PC 133 Intel810 Baby AT Mainboard HARDWARE SETUP 3 2 INSTALLING THE DRAM MODULES This mainboard has two DIMM sockets designed on the mainboard as shown in the following diagram
58. scription for all the details POWER BUTTON The power button can be programmed by COMS setup program and it has different features Please refer to page 3 16 for detail function description O KEYBOARD PASSWORD OR HOT KEY This mainboard allows you to use your personal password or a combination of hot key to power on your PC system When the jumper setting on JP1 is Enabled the keyboard OnNow function will be activated Under this circumstance this mainboard will keeps scanning the keyboard status waiting for the correct password or hot key input even when the system power is off the stand by 5V is still working and the power LED on the keyboard is still active When you have selected the keyboard hot key to power on the PC system you will be able to use keyboard hot key to power on the PC system you can use the power button to power on the PC system all the time Please refer to Section 4 7 Integrated Peripherals O PS 2 MOUSE LEFT OR RIGHT MOUSE BUTTON If you have a PS 2 mouse connected to the system you may change the setup in the BIOS and use the mouse click to turn on the PC system power Please refer to section 4 7 POWER ON FUNCTION for the BIOS setting To use the mouse key to turn on the PC system power the mouse click must be done quickly and continually Basically 2 5 quick clicks on the mouse key left key or right key will turn the power immediately Note I This feature is not available on
59. se the User Password to log into the BIOS setup program you can only select User Password SAVE amp EXIT SETUP and EXIT WITHOUT SAVING from the main menu Use Supervisor Password to log into the PC system you will have the complete right to on all BIOS settings 2 When System is selected in Security Option When turn on the PC system it will request you to enter the Password Without correct password PC system will stop and the operation system won t be loaded B When there is no password stored in the SUPERVISOR PASSWORD 1 When Setup is selected in Security Option Users can use the User Password to log into the BIOS setup program and they can make all the change in the BIOS setup program 2 When System is selected in Security Option When turn on the PC system it will request you to enter the Password Without the correct password the PC system will stop and the operation system will not be loaded 4 23 Intel810 Baby AT Mainboard AWARD BIOS SETUP 4 15 SAVE amp EXIT SETUP EXIT WITHOUT SAVING CMOS Setup Utility Copyright C 1984 1999 Award Software Standard CMOS Features Frequency Voltage Control Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password Power Management Setup PNP PCI Configuration PC Health Status ESC Quit fi Select Item F10 Save amp Exit Setup Time Date Hard Dis
60. t CN16 CD Audio AT CN2 PS 2 Mouse K B L Audio Game CN15 ATX Power C NE CNS LPT CN14 AT Power JP7 Clear Password g L L 4 ba 4 3 wre 4 4 LOTS IOd CN6 CN7 USB JP1 K B OnNow sel CN11 SB Link JP6 Clear CMOS CN23 TV OUT JP2 Vcore Range JP4 Adjust Vcore SWI We b CN13 CPU Fan Ll DIMM 1 SW1 CN25 AIR Bus L DIMM 2 Select CPU clock Ratio CN10 IDE2 mem N8 FDC IDEI AN 1 L CN17 Cooling 2 SPK Speaker con PW Power SW CAUTION SL Sleep LED 1 Wrong type of USB cable will destroy TL Turbo LED either the USB device or the M B PWR LED amp KBLOCK HL HDD LED Please always handle the USB cable RS Reset button carefully when installing USB devices IMPORTANT NOTICE 1 This mainboard will have either one or two CPU sockets installed When there are two CPU sockets on the mainboard you may install only one CPU on the board 2 When there is the CPU booster comes with the board it will support 133MHz CPU and PC 133 SDRAM 3 The standby voltage is always active Whenever you are installing any component on the mainboard BE SURE TO REMOVE THE POWER CABLE Intel810 Baby AT Mainboard INTRODUCTION 1 5 SPECIFICATIONS CPU When there are two CPU sockets on this mainboard it wi
61. ter how serious of damage is made to your system BIOS whenever there is the KEYBIOS connected to the AIR Bus the system BIOS will be replaced by the KEYBIOS and that will keep your PC system alive More than just a mainboard The KEYBIOS is a programmable device and many special software tools can be introduced on it Since KEYBIOS is active before the OS is loaded so it will provide lots of amazing feature For example the KEYBIOS TM can be used for security purpose and that will keep the unauthorized person away from your PC system The design of the AIR Bus is simple but the features introduced to the KEYBIOS TM will come out with many amazing function and you will discover that what you received is more than just a regular mainboard Please contact your dealer for more detail features on the AIR bus 1 2 Intel810 Baby AT Mainboard INTRODUCTION 1 3 CPU BOOSTER The 810DT comes with a CPU booster and it will allow you to install 133MHz FSB Pentium III processor on the socket 370 to increase the system performance Why CPU Booster Over clock is popular to many users Unfortunately over clock the CPU may cause serious damage to the CPU and mainboard However the CPU booster will increase the system performance by changing the memory architecture to PC 133 and you do not have to worry about the potential damage When CPU booster is installed on the mainboard CPU and the memory subsystem are both runn
62. the COM port mouse serial mouse 2 To use the PS 2 mouse power on the PC system JPI must me Enabled RTC ALARM PC system can be waked up by the RTC setting in the CMOS You can set the alarming date and time in the RTC memory When RTC alarms the PC system will be triggered and wake up automatically on the date and time which you selected in the BIOS setup program 2 2 Intel810 Baby AT Mainboard INTSTALLATION Enable the Resume by Alarm selection in the BIOS setup utility and then you will see the input request for the date and time the Resume by Alarm Is located in the POWER MANAGEMENT SETUP please refer to Section 4 8 When you have stored the RTC alarm setting the PC system will be turned on automatically according to the date and time which is recorded in the CMOS memory O MODEM RING IN When you have an external modem installed you can leave the PC system power off Whenever there is the incoming message the PC system will be triggered by the ring in signal and wake up automatically to receive the message for you From now on you can tell your PC system to receive the fax message for you In order to use the ring in signal to wake up your PC system you will have to use the EXTERNAL MODEM and have it connected to one of the SERIAL PORTS COMI or COM2 on the mainboard When the mainboard detects the ring in signal from the serial port the system power will be turned on and start to receive the incomi
63. update If you interrupt the BIOS updating before it is completed then you will have an incomplete system BIOS on your mainboard and you will be unable to use the mainboard afterward 2 Make sure to get the correct system BIOS If you are using the wrong BIOS code to update the system BIOS the mainboard may not be able to work anymore unless you send the mainboard to the technical center for technical support 3 Don t exchange the system BIOS with other mainboard If you take the system BIOS from other mainboard and put it on this mainboard you may find that your PC system is unstable to work 4 Always check the flash ROM capacity The flash ROM is the component where we can store the system BIOS If you down load the wrong BIOS code you will be unable to upgrade the system BIOS SYSTEM BIOS UPDATE PROCEDURES STEP 1 VISIT THE WEB PAGE AND DOWN LOAD THE RELATED FILES 1 Please check with your dealer and get the home page address 2 Visit the web site and down the following files AWDFLASH EXE Award BIOS update program 810DW BIN PT 810DTC mainboard BIOS code 5 1 Intel810 Baby AT Mainboard UPDATE THE SYSTEM BIOS STEP2 PREPARE AN ENVIRONMENT AND READY FOR BIOS UPDATE 1 The BIOS update procedure can not be interrupted so the multi task environment like Windows is not recommended You have to handle the BIOS update in the DOS environment Do not use the DOS opened in the window environment 2 Get a blan
64. ur HDD support the SMART feature you may enable this item and it will monitor and report the HDD healthy status to you Report NO FDD for WIN 95 default setting NO If there is no FDD installed in the PC system you may select YES in this field so that WIN 95 will KNOW there is no FDD connected to the mainboard XXXX XXXX Shadow default setting Disabled These fields allow you to enable disable the shadow on the appropriate memory segment Intel810 Baby AT Mainboard AWARD BIOS SETUP 4 6 ADVANCED CHIPSET FEATURES CMOS Setup Utility Copyright C 1984 1999 Award Software Advanced Chipset Features SDRAM CAS Latency Time KEN Item Help SDRAM Cycle Time Tras Trc 6 8 SDRAM RAS to CAS Delay 3 Menu Level gt SDRAM PAS Precharge Time 13 System BIOS Cacheable Disabled Video BIOS Cacheable Disabled Memory Hole at 15 16 Disabled CPU Latency Timer Disabled Delayed Transaction Enabled On Chip Video Windows Size 64MB SDRAM Speed Selection The first four fields on the screen are used to adjust the SDRAM timing Use these fields to configure the DRAM parameter properly will give you the best performance However improper setting on these fields will cause your PC system become extremely unstable Basically please do not attempt to make the change on these fields unless you are the professional technician System BIOS Cacheable default setting Disabled Select Enabl
65. y 2 Insert the CD diskette into the CD ROM Drive suppose it is D which comes with the mainboard 3 Change the directory to D Driver mainboard Intel 8 1 0 inf 4 Install the program in the intelinf directory first Please run the SETUP EXE program and it will create a directory program file INTEL inf preload The purpose of such program is to tell the Windows the mainboard information so that it will work normally 5 Install the program located in the infinst directory Run SETUP EXE 6 When the above setup procedures are completed the PC system will be restarted Sometimes Windows may be unable to detect the device such ULTRA DMA interface In this case you may have to specify the directory program file INTEL inf preload and insert your Windows CD into the CD ROM drive and Windows will load the related information 7 Change the directory to Driver mainboard Intel 810 VGA and then choose the operation system to install the device driver of the onboard VGA interface 8 Change the directory to Driver mainboard Intel 810 alc100 and then choose the operation system to install the onboard audio device driver 9 If you want to use the hardware monitoring feature designed on the mainboard please change the directory to Driver mainboard hardware monitoring W83627HF Choose the operation system and then run the SETUP EXE program and then follow the screen instruction to complete the installation Note The seque
66. ystem memory to store 3D texture mapping data to increase the video display performance You may use this field to define the memory size which you prefer to use for the AGP card The memory size selectable in this field can be Disable or 64MB DVMT When you select 64MB DVMT it does not mean that the PC system will use that much memory Then memory size defined in this field will be the maximum memory which Windows 95 98 can use to story the 3D texture When you select the 64MB DVMT you will see 1024K memory is allocated as the share memory when you power on the PC system When you start the Windows operation system Windows will allocate the required display share memory dynamically If you select disable the onboard VGA interface will be disabled Since there is no AGP slot on the mainboard so you will to PCI Otherwise there will be display to your PC system Intel810 Baby AT Mainboard AWARD BIOS SETUP 4 7 INTEGRATED PERIPHERALS CMOS Setup Utility Copyright C 1984 1999 Award Software Integrated Peripherals On Chip Primary PCI IDE Enabled Item Help On Chip Secondary PCI IDE Enabled IDE Primary Master PIO Auto Menu Level gt IDE Primary Slave PIO Auto IDE Secondary Master PIO Auto IDE Secondary Slave PIO Auto IDE Primary Master UDMA Auto IDE Primary Slave UDMA Auto IDE Secondary Master UDMA Auto IDE Secondary Slave UDMA Auto USB Contro

810DTC/810DT+ Pentium II/III Celeron Twin Processor

Contents

Download Pdf Manuals

Related Search

Related Contents