Manual - Amazon Web Services
Contents
1. Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside e Never operate this unit when it s cover is removed e Never plug this unit in to a dimmer pack e Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged e This unit is intended for indoor use only use of this product out doors voids all warranties e During long periods of non use disconnect the unit s main power e Always mount this unit in safe and stable matter e Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 23 for cleaning details e Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances inclu ding amplifiers that produce heat The fixture should be serviced by qua2. 12 12 MEGA aD GO FLOOD PAR User Instructions Mega Go Flood Par Introduction Unpacking Thank you for purchasing the Mega Go Flood Par by ADJ Products LLC Every Mega Go Flood Par has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during ship ping If the carton appears to be damaged carefully inspect your fix ture for any damage and be sure all accessories necessary to operate the unit has arrived intact In the case damage has been found or parts are missing please contact our toll free customer support number for further instructions Do not return this unit to your dealer without first contacting customer support Introduction The Mega Go Flood Par is a rechargeable lithium bat tery powered DMX intelligent low profile LED par fixture This unit give you the freedom to set up your fixture where ever you wish without the restrictions of power The built in battery will keep charge for up to 4 5 hours full on from a full single charge This fixture can be used in a stand alone mode or connected in a Master Slave configuration This wash has five operating modes Sound Active mode Auto mode RGB mode Static Color mode and DMX control mode Customer Support ADJ Products LLC provides a customer support line to provide set up help and to answer any question should you encounter problems during yo
3. 100 O 255 0 100 MASTER DIMMER 0 100 0 255 ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 17 5 Channel Mode RED 0 100 GREEN 0 100 BLUE 0 100 MASTER DIMMER 4 O oas 0 100 5 0 255 COLOR MACROS See 1 Channel DMX mode for colors Channels 1 2 and 3 will not work when Channel 5 is being used Mega Go Flood Par Mega Go Flood Par 6 Channel Mode Channel Valua 0 100 2 GREEN 0 100 O 255 100 See 1 Channel DMX mode for colors STROBING NOTHING STROBING SLOW FAST MASTER DIMMER 0 100 Channels 1 2 and 3 will not work when Channel 4 is being used Na ka ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 18 Mega Go Flood Par 7 Channel Mode Mega Go Flood Par 7 Channel Mode Function RED PROGRAMS SOUND ACTIVITY 0 100 168 175 SOUND MODE 5 GREEN 176 183 SOUND MODE 6 0 100 184 191 SOUND MODE 7 BLUE 192 199 SOUND MODE 8 0 100 200 207 SOUND MODE 9 COLOR MACROS 208 215 SOUND MODE 10 See 1 Channel DMX mode for colors 216 223 SOUND MODE 11 STROBING PROGRAM SPEED 224 231 SOUND MODE 12 NOTHING 232 239 SOUND MODE 13 STROBING SPEED CONTROL 240 247 SOUND MODE 14 SLOW FAST 248 255 SOUND MODE 15 PROGRAMS SOUND ACTIVITY MASTER DIMMER OFF 0 100 PROGRAM 1 Channels 1 2 and 3 will not work when Channel 4 is being used 16 23 PROGRAM 2 24 31 PROGRAM 3 32 39 PROGRA
4. Mode Choose one of the three colors to remain static or adjust the intensity of each color to make your desired color e DMX control mode This function will allow you to control each individual fixtures traits with a standard DMX 512 controller such as ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 10 Mega Go Flood Par Operating Instructions as the ADJ Show Designer DMX Mode Operating through a DMX controller gives the user the freedom to create their own programs tailored to their own individual needs This function also allows you to use your fixtures as spot lights The Mega Go Flood Par has 7 DMX modes 1 Channel mode 2 Channel mode 3 Channel mode 4 Channel mode 5 Channel mode 6 Channel mode and a 7 Channel mode See pages 16 20 for each modes DMX traits 1 This function will allow you to control each individual fixture s traits with a standard DMX 512 controller 2 Torun your fixture in DMX mode press the MODE button until A XXX is displayed XXX represents the current displayed ad dress Use the UP or DOWN buttons to select your desired DMX address then press the SETUP button to select your DMX Channel mode 3 Use the UP or DOWN buttons to scroll through the DMX Channel modes The Channel modes are listed below To run the 1 Channel Mode press the MODE button until Ch 01 is displayed This is the 1 Channel DMX Mode To run the 2 Channel Mode press the MODE b
5. teries to provide extra safety protection The battery pack is constructed in a way that no short circuit will occur which may cause smoke or fire 3 3 Do No Disassemble the Batteries 1 Never disassemble the batteries Doing this may cause a internal short circuit in the battery which may lead to harmful fumes fire explosion or other prob lems 2 Electrolyte Gel is harmful Electrolyte Gel should not leak from the LIR battery Should the electrolyte gel come into contact with the skin or eyes flush the ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 5 Mega Go Flood Par Battery Precautions area of contact immediately with fresh water and seek medical attention immediately 3 4 Do Not Expose the Battery to Heat or Fire Never incinerate or dispose of the batteries in fire This may cause an explosion which would be very dangerous 3 5 Do Not Expose the Battery to water or liguids Never soak drop the batteries in liguids such as water seawa ter drinks such as soft drinks juices coffee or other 3 6 Battery Replacement For battery replacement please contact ADJ Products LLC cus tomer support 800 322 6337 3 7 Do Not use a damaged Battery The battery could be damaged during shipping caused by shock Should the battery be found damaged including dam ages to the plastic casing of the battery deformation of the battery package smelling of an electrolyte or leakage of the electrolyte gel o
6. the 16 programs using the and buttons You can control the speed of the Auto Run by pressing the SPEED button first and then pressing the and buttons You can control the fade speed of the Auto Run sy pressing the FLASH button first and then pressing the and buttons PROGRAM SELECTION This button will activate the color macros mode Use the or to scroll through the 35 colors Once you have found your color you can press the Flash Button to activate ce II strobing and use the or to adjust the Flash rate FLASH This button will activate the flash strobe effect You can control the flash speed by pressing the and buttons SPEED Press this button and use the amp buttons to adjust the speed of the Auto run mode or adjust the sound sensitivity while in Sound Active mode SOUND ACTIVE This button activates sound active mode Use the or to scroll through the 15 sound active programs Press the SPEED button and use the amp buttons to adjust the sound sen sitivity 66 II ce JI R G B Press either one of these buttons and the press the or to adjust the brightness Press the Flash Button to activate strobing ced and use the or to adjust the Flash rate y 33 and Use these buttons to adjust the flash rate speed of a Auto Run mode sound sensiti
7. the serial number has been altered or removed if the product is modified in any 1 Check that the DMX cables are connected properly and are manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the g sali H product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior wired gorrecily pin 3 is hot polit Sonic other DMX devices written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because pin 2 may be hot Also check that all cables are connected not properly maintained as set forth in the instruction manual to the right connectors it does matter which way the inputs D This is not a service contract and this warranty does not include maintenance cleaning or periodic check and outputs are connected up During the period specified above ADJ Products LLC will replace defective parts at its expense s with new or refurbished parts and will absorb all expenses for warranty service and repair labor by Unit does not respond to sound reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this H H i H i i warranty shall be limited to the repair of the product or replacement thereof including parts at the sole 1 Quiet or high pitched sounds will not activate the unit discretion of ADJ Products LLC All products covered by this warranty were manufactured after Aug
8. M 4 40 47 PROGRAM 5 48 55 PROGRAM 6 56 63 PROGRAM 7 64 71 PROGRAM 8 72 79 PROGRAM 9 80 87 PROGRAM 10 88 95 PROGRAM 11 When using Channel 6 values 8 135 Channel 5 will control the speed of the programs and Channel 4 will control the fade speed of the programs When using Channel 6 values 136 255 Channel 5 will control the sound sensitivity Sound sen sitivity control will start working after Channel 5 is past the DMX value of 31 96 103 104 111 112 119 120 127 128 135 PROGRAM 12 PROGRAM 13 PROGRAM 14 PROGRAM 15 PROGRAM 16 136 143 SOUND MODE 1 144 151 SOUND MODE 2 152 159 SOUND MODE 3 160 167 SOUND MODE 4 ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 19 ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 20 Mega Go Flood Par Photometric Chart Distance Centimeters ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 21 Mega Go Flood Par Battery Status amp Charging Battery Status This function is used to check the life status of the battery Plug the fixture in and press the MODE button until bXXX is displayed XXX represents an number between 000 and 100 The number that is displayed is the remaining battery life If b is displayed
9. a Go Flood Par Operating Instructions Once you have set your desired color change speed press the SET UP button to move on to F XX color fade Use the UP or DOWN buttons to set the color fade speed to F 00 This means the color fade is off and the fixture will now color change at the speed you have set To run the fixture in color fade reverse the instructions Set your color fade speed and set the color change speed to SP 01 Static Color Mode 1 Plug the fixture in and press the MODE button until CLXX is displayed 2 There are 35 colors to choose from Select your desired color by pressing the UP and DOWN buttons After you have selected your desired color you can activate strobing by pressing the SET UP button to enter the Flash strobe mode 3 FS XX will be displayed this is Flash mode The Flash can be adjusted between FS 00 flash off to FS 15 fastest flash Auto Run Default This will reset the Auto Run mode back to the default settings 1 Plug the fixture in and press the MODE button until dXX is dis played XX represents either on or OFF 2 Press the SET UP button until dEFA is displayed 3 Press the UP and DOWN buttons simultaneously Press the MODE button to exit ADJ RFC Remote Control On Off This function is used to activate and deactivate the ADJ RFC Remote Control When this function is activated you can control the fixture using t
10. but ton to enter the Flash strobe mode 6 FS XX will be displayed this is Flash mode The Flash can be adjusted between FS 00 flash off to FS 15 fastest flash Sound Active Mode In this mode the Mega Go Flood Par will react to sound and chase through the different colors 1 Plug the fixture in and press the MODE button until SoXX is dis played XX represents the sound active mode 1 15 currently displayed 2 The fixture will now change via sound 3 Press the SET UP button to adjust the sound sensitivity SJ X should be displayed Use the UP or DOWN buttons to adjust the sensitivity SJ 1 is the lowest sensitivity SJ 8 is the highest Auto Run Mode In this mode the Mega Go Flood Par will run 1 of 16 auto programs The auto run program can be either a fade program or a simple color change program 1 Plug the fixture in and press the MODE button until APXX is dis played XX represents the program number 1 16 currently dis played 2 After you have chosen your desired program you need to decide if you would like the program to fade through colors or simply change Press the SET UP button until either SP XX color change speed or F XX color fade speed is displayed 3 If you select color change use the UP and DOWN buttons to adjust the speed between SP 01 Slowest and SP 99 fastest ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 12 Meg
11. e XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems o and interference It is always advisable LZ s to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX 4 of the last fixture Figure 4 Figure 2 XLR Pin Configuration Pin 1 lt Ground Pin 2 Data Compliment negative preo a S S Susan iso evita Pin 3 Data True positive 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion 3 Pin XLR Female Out 5 Pin XLR Male In Ground Shield Pin 1 Data Compliment signal Pin 2 Data True signal Pin 3 Not Used Do Not Use Not Used Do Not Use ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 9 Mega Go Flood Par Operating Instructions Operating Power There are two ways to supply power to this unit battery power or AC power AC Power To run the unit using AC pow
12. er plug the unit into a power source and put the Load Switch into the ON position When using AC power make sure the Battery Switch is in the OFF position e Battery Power To run the unit using Battery power put the Load and Battery Switches in the ON position LED Display On Off To set the LED display to turn off after 20 seconds press the MODE button until don is displayed press the UP button to display doff Now the display will disappear after 20s Press any button to turn the display on again Be advised though that the display will turn off automatically after 20 seconds To set the display press the MODE button until dXX is displayed Use the UP or DOWN buttons to select either don LED display on at all times doFF LED display shuts off after 20 seconds LED Display Inversion Follow these instructions to flip the display 180 so that the display can be read upside down 1 Plug the fixture in and press the MODE button until dXX is dis played XX represents either on or OFF 2 Press the SET UP button until Stnd is displayed 3 Press the UP or DOWN buttons to reverse the display 180 Operating Modes The Mega Go Flood Par has five operating modes Sound Active mode The unit will react to sound chasing through the built in programs e Static Color Mode There are 35 colors to choose from e Auto Mode There are 3 Auto Modes to choose from RGB
13. hannel modes please see page 11 for DMX mode The DMX address is set on the back panel of the Mega Go Flood Par Your unit and your DMX controller require a standard 3 pin XLR connector for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all pro lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split Figure 1 Notice Be sure to follow figures two and three when making your own ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 8 Mega Go Flood Par Set Up cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR XLR Male Socket XLR Female Socket 1 e 2 SIT Figure 3 Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the femal
14. he ADJ RFC Please see page 15 for the controls and func tions 1 Plug the fixture in and press the MODE button until dXX is dis played XX represents either on or OFF 2 Press the SET UP button until rFXX is displayed XX repre sents either on or oF 3 Press the UP or DOWN buttons to either activate the remote func tion On or deactivate it Off ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 13 Mega Go Flood Par Operating Instructions Battery Life This menu is used to check display the battery life 1 Plug the fixture in and press the MODE button until bXXX is dis played XXX represents a number between 0 100 The number that is displayed is the remaining battery life If b is displayed it means either the battery is dead or your running the unit on AC power Mega Go Flood Par Master Slave Configuration Master Slave Configuration This function will allows you to link units together to run in a Master Slave mode In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units built in programs Any unit can act as a Master or as a Slave however only one unit can be pro grammed to act as the Master Master Slave Connections and Settings 1 Daisy chain your units via the XLR connector on the rear of the unit Use standard XLR data cables to link your units together Remember that
15. it means the battery is dead or you are running the unit on AC power Please do not let the battery fully die this severly shortens the life of the battery Example If b050 is displayed the battery is at half life If b025 is displayed the battery is at 25 life NOTE When the battery is charging or if the battery life is below 30 the digital display will flicker Battery Recharge To recharge the battery plug the supplied AC cord into the AC input on the side of the unit and plug the other end into a matching power supply It takes about 6 5 hours to reach full charge The display will STOP flashing when the unit reaches 100 charge Note When unplugging the unit from charging and then applying power via battery there will be a minimal charge drop For a faster recharge put the Load Switch in the Off position and the Battery Switch in the ON position ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 22 Mega Go Flood Par Fuse Replacement UERCH eX Mi Li Warranty i i i MANUFACTURER S LIMITED WARRANTY Disconnect the unit from its POWT SOUICG Remove the power cord A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products from the unit Once the cord has been removed you will find that the to be free of manufacturing defects in material and workmanship for a prescribed period from fuse holder is located inside the power socket Insert a flat head screw
16. lified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 4 Mega Go Flood Par Battery Precautions 1 Handling of Batteries 1 1 Do Not Short Circuit the Battery Try to never short circuit the battery It generates a very high current which could cause the battery to overheat which may result in electrolyte gel leakage harmful fumes or explosion The LIR tabs may easily short circuit by placing them on con ductive surface A short circuit may lead to heat build up and damage of the battery An appropriate circuitry with PCM is employed to protect accidental short circuit of the battery pack 1 2 Mechanical shock Droping the unit impact hit bending etc may cause failure or shortend life of the LIR battery 3 Other 3 1 Battery connection 1 Direct soldering of wire leads or devices to the battery is strictly prohibited 2 Lead tabs with pre soldered wiring shall be spot welded to the batteries Direct soldering may cause damage of compo nents such as separator and insulator by heat build up 3 2 Prevention of short circuit within a battery pack There is enough insulation layers between wiring and the bat
17. r The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper included in the shipping carton If the unit is under warranty you must provide a copy of your proof of purchase invoice You may obtain a R A number by contacting our customer support team on our customer support number All pack ages returned to the service department not displaying a R A number on the outside of the package will be returned to the shipper Mega Go Flood Par Installation The unit should be mounted using a mounting clamp not provided affixing it to the mounting bracket that is provided with the unit Always ensure that the unit is firmly fixed to avoid vibration and slip ping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit s weight Also always use a safety cable that can hold 12 times the weight of the unit when installing the fixture The equipment must be installed by a professional and it must be installed in a place where it is out of the reach of people s grasp ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 3 Mega Go Flood Par Safety Precautions To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit
18. r other DO NOT use the battery A battery with a odor of electrolyte or a gel leakage should be placed away from fire to avoid fire or explosion 4 Battery Storage When storing the battery it should be stored at room tempera ture with a charge of at least 50 We recommend that during long periods of storage that the battery be charged every 6 months Doing this will prolong the life of the battery and will also make sure that the battery charge does not fall below the 30 mark 5 Other Chemical Reaction Because batteries utilize a chemical reaction battery per formance will deteriorate over time even if stored for a long period of time without being used In addition if the various usage conditions such as charge discharge ambient tempera ture etc are not maintained within the specified ranges the ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 6 Mega Go Flood Par Battery Precautions life expectancy of the battery maybe shortened or the device in which the battery is used may be damaged by electrolyte gel leakage If the batteries cannot maintain a charge for long periods of time even when they are charged correctly this may indicate it is time to change the battery ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 7 Mega Go Flood Par Set Up Power Supply The ADJ Mega Go Flood Par contains a automatic voltage switch which will auto sense the voltage when it is plugged in
19. the Male XLR connector is the input and the Female XLR con nector is the ouput The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only 2 Connect the first Slave unit to the Master 3 Set the Master unit to your desired mode of operation The Slave unit will now follow the Master Mega Go Flood Par Power Cord Daisy Chain With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 30 fixtures maximum After 30 fixtures you will need to use a new power outlet They must be the same fixtures DO NOT mix fixtures NOTE Fixtures cannot be power cord daisy chained and run by battery power ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 14 Mega Go Flood Par RFC Operation The ADJ RFC remote sold seperately has many different functions and allows you to control your Mega Go Flood Par from long dis tance The ADJ RFC remote can control your system up to 150 ft To use the remote you must first activate the fixtures receiver to activate the receiver please see the instructions on page 10 BLACKOUT Pressing this button will blackout the fixture Press and hold this button for 3 seconds to return to default settings and default running mode AUTO RUN This button will run 1 of 16 automatic programs You can scroll through
20. the date of purchase see specific warranty period on reverse This warranty shall be valid only if the S A i product is purchased within the United States of America including possessions and driver into the power socket and gently pry out the fuse holder Remove territories It is the owner s responsibility to establish the date and place of purchase by acceptable the bad fuse and replace with a new one The fuse holder also has a evidenceyatthe time service I8 sought holder for a Spare fuse B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product 7 only to the ADJ Products LLC factory All shipping charges must be pre paid If the reguested repairs or Use Fe Go Flood Par Trouble Shooting service including parts replacement are within the terms of this warranty ADJ Products LLC will pay z return shipping charges only to a designated point within the United States If the entire instrument is Listed below are a few common problems the user may encounter sent it must be shipped in it s original package No accessories should be shipped with the product If with solutions any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof Unit not responding to DMX C This warranty is void if
21. the only written warranty applicable to ADJ Products LLC Products and every ays supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore 3 Always be sure to dry all parts completely before plugging published This warranty was revised after December 1 2012 the unit back in Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED Laser Products and lamps e Laser Products 90 Day Limited Warranty L E D Products 3 year 1095 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty Only the L E D s carry a 3 year warranty ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 23 ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 24 Mega Go Flood Par Notes Mega Go Flood Par Notes ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 25 ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 26 Mega Go Flood Par Specifications Model Mega Go Flood Par Voltage 100V 240V 50 60H
22. to the power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via the DATA IN and DATA OUT XLR ter minals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compli ant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX Operation The Mega Go Flood Par can be controlled via DMX 512 protocol The Mega Go Flood Par has 7 DMX c
23. ur set up or initial operation You may also visit us on the web at www adj com for any comments or sugges tions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail supportCadj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact ADJ Products LLC PLEASE recycle the shipping carton when ever possible ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 2 Mega Go Flood Par Features e Rechargeable Lithium Battery e Mulit Colors Five Operating Modes e Electronic Dimming 0 100 e Built in Microphone e DMX 512 protocol 3 Pin DMX Connection Seven DMX Modes 1 Channel Mode 2 Channel Mode 3 Channel Mode 4 Channel Mode 5 Channel Mode 6 Channel Mode and 7 Channel Mode e ADJ RFC compatiable Not Included e Power Cord Daisy Chain See page 14 Mega Go Flood Par Warranty Registration The Mega Go Flood Par carries a 3 year limited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A numbe
24. ust 2 Make sure that Sound Active mode is activated 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon it s products without any obligation to include these changes in any products theretofore manufactured Mega Go Flood Par Cleaning No warranty whether expressed or implied is given or made with respect to any accessory supplied with Due to fog residue smoke and dust cleaning the internal and exter products described above Except to the extent prohibited by applicable law all implied warranties made nal optical lenses must be carried out periodically to optimize lig ht by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or output implied including warranties of merchantability or fitness shall apply to this product after said period 1 Use normal glass cleaner and a soft cloth to wipe down the has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product outside casing 2 Clean the external optics with glass cleaner and a soft cloth 20d This warranty is
25. utton until Ch 02 is displayed This is the 2 Channel DMX Mode To run the 3 Channel Mode press the MODE button until Ch 03 is displayed This is the 3 Channel DMX Mode To run the 4 Channel Mode press the MODE button until Ch 04 is displayed This is the 4 Channel DMX Mode To run the 5 Channel Mode press the MODE button until Ch 05 is displayed This is the 5 Channel DMX Mode To run the 6 Channel Mode press the MODE button until Ch 06 is displayed This is the 6 Channel DMX Mode To run the 7 Channel Mode press the MODE button until Ch 07 is displayed This is the 7 Channel DMX Mode 4 Please see pages 16 20 for DMX values and traits 5 After you have chosen your desired DMX Channel mode plug in the fixture via the XLR connections to any standard DMX control ler ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 11 Mega Go Flood Par Operating Instructions RGB Dimmer Mode 1 Plug the fixture in and press the MODE button until 2 When r XXX is displayed you are in Red dimming mode Press the UP and DOWN buttons to adjust intensity 3 When G XXX is displayed you are in Green dimming mode Press the UP and DOWN buttons to adjust intensity 4 When b XXX is displayed you are in Blue dimming mode Press the UP and DOWN buttons to adjust intensity 5 After you have adjusted the RGB colors to make your desired color you can then activate strobing by pressing the SET UP
26. vity and the intensity output of the RGB colors These buttons are also used to scroll through the differ ent color macros auto run programs and sound active programs ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 15 Mega Go Flood Par 1 Channel Mode COLOR MACROS 0 10 OFF 11 17 BASTARD AMBER 18 24 MEDIUM AMBER 25 31 PALE AMBER GOLD 32 38 GALLO GOLD 39 45 GOLDEN AMBER 46 52 LIGHT RED 53 59 MEDIUM RED 60 66 MEDIUM PINK 67 73 BROADWAY PINK 74 80 FOLLIES PINK 81 87 LIGHT LAVENDER 88 94 SPECIAL LAVENDER 95 101 LAVENDER 102 108 INDIGO 109 115 HEMSLEY BLUE 116 122 TIPTON BLUE 123 129 LIGHT STEEL BLUE 130 136 LIGHT SKY BLUE 137 143 SKY BLUE 144 150 BRILLIANT BLUE 151 157 LIGHT GREEN BLUE 158 164 BRIGHT BLUE 165 171 PRIMARY BLUE 172 178 CONGO BLUE 179 185 PALE YELLOW GREEN 186 192 MOSS GREEN 193 199 PRIMARY GREEN 200 206 DOUBLE CTB 207 213 FULL CTB 214 220 HALF CTB 221 227 DARK BLUE 228 234 WHITE 235 241 FULL RED 242 248 FULL GREEN 249 255 FULL BLUE ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 16 Mega Go Flood Par 2 Channel Mode Nu Ne 0 255 COLOR MACROS See 1 Channel DMX mode for colors O 255 DIMMER 0 100 Channel Value Funeton O 255 0 100 O 255 0 100 BLUE 0 255 0 100 Mega Go Flood Par 4 Channel Mode eee prameni O 255 0 100 O 255 0
27. z Battery Life 4 5 Hours Full On Full Charge LEDs 27 TRI SMD 3 in 1 RGB LED s Beam Angle 120 Degrees Working Position Any safe working position Power Draw 18W Power Cord Daisy Chain 30 Fixtures Max Fuse 1 Amp Weight 3lbs 1Kgs Dimensions 8 L x 7 75 W x 3 75 H 202 x 195 x 92mm Colors RGB Color Mixing DMX Channels 7 DMX Modes 1 Channel Mode 2 Channel Mode 3 Channel Mode 4 Channel Mode 5 Channel Mode 6 Channel Mode amp 7 Channel Mode Warranty 3 Year 1 095 days Limited Warranty See Warranty page for details Auto Sensing Voltage This fixture contains a automatic voltage switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC www adj com Mega Go Flood Par User Manual Page 27 ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info adj com A D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Netherlands Follow Us On HOM facebook com americandj twitter com americandj youtube com adjlighting Tel 31 45 546 85 00 Fax 31 45 546 85 99
Download Pdf Manuals
Related Search