Home

Quick installation and user guide

1. tighten clamp screw 4 Connect a jar Push any black jar tube into the coupling on the jar lid Incase the connector does not slide in please first pull the outer ring of the snap shut coupling downward 5 Choose Quality assurance l Quality Assurance For the standard recipes a QA level has been set _ enabled level 3 Quality Assurance You can disable the QA st touching this button 2nabled levels or change the level by eicotne CY 6 Press the Start Continue button 7 Process report information During a recipe and after it has finished a Process report will be displayed o B will appear if a gas connection has the wrong working pressure The actual pressure will be displayed Re adjust the reducing valve and retry O will appear if vacuum is detected in the jar Disconnect the jar and air it by pushing into the snap shut coupling with an object e g a pencil o E will appear if a jar connection is not used or if a jar has failed the corresponding Quality Assurance test o In case td appears for one of the parts of the Quality Assurance this means the jar has passed that particular test o Incase td appears under Ready it means that the jar can be uncoupled o Pull the outer ring of the snap shut coupling downward Hold the jar tube 8 The Anoxomat is ready for the next job A Never switch the system off when it is in operation Only switch off when the Main Screen has been displayed for a
2. Quick installation guide 1 Check availability and unpack Anoxomat User manual on CD Rom ee Parts package Gas tube s 2 tube clamps per tube parts package 1 reserve Power supply cable wT soft touch pen 1 penholder with double sided adhesive tape Fuses One Mart jar and a catalyst One gas cylinder not from Mart One reducing valve if ordered from Mart Tools not from Mart o An adjustable nut spanner to tighten Printer the reducing valve o Adjustable joint pliers to tighten the gas tube clamps Recipe printer with accessories if ordered from Mart Install the printer View directions of the printer Printer connect o Connect the printer to the socket on the bottom of the Anoxomat gray printer cable o Put the starter roll of paper into the printer o Connect the printer to the net with the power supply assembly 2 Install the Gas supply Mount the reducing valve on the gas cylinder use the adjustable nut soanner Connect the reducing valve with gas input number 1 gas input of the Anoxomat with a gas tube from the parts package use a tube clamp on each side use the adjustable joint pliers to tighten the gas tube clamps Tube clamp Open the gas cylinders main supply and set the pressure to 1 8 bar precisely gas cylinder 3 Remove red protection foil from touch screen Keep it available 4 Use the power cable to connect the Anoxomat to the net 5 Swi
3. few seconds Never use sharp objects pens pencils etc or anything leaving ink marks on the screen The Mart jars are never to be cleaned with alcohol and not to be exposed to temperatures of more than 80 C For further and more detailed information please view the operation Manual on enclosed CD Rom Mart Microbiology B V Version1 dd 17 2 2012
4. tch the system on and wait till the main screen appears Your Anoxomat is equipped with a touch screen You can use your fingers or the supplied soft touch pen A Never use sharp objects pens pencils etc or anything leaving ink marks on the screen 6 Go to O op on touch screen of the Anoxomat Gas 1 Enter the Set up code from the red sticker a5 M2 10 CO2 SHH _ SOF LO los 1O Ae 7 Choose the gas composition of your Gas other gas composition 8 Ifa printer was ordered go to sunillteian Enter the Printer code from the red protection foil and touch Pe 9 _ des this menu to go to the main screen For installation assistance please contact your local Anoxomat supplier or call Mart Microbiology 31 0 512 58 22 33 Mart Microbiology B V Version1 dd 17 2 2012 Quick usage guide 1 Filla jar Put your inoculated dishes tubes micro well plates or other samples in the jar with the help of the Petri dish holder Pee eee eee eee eee ee er CLL 2 Choose a recipe on the main screen of the Anoxomat Wicro aeraphilc 6 02 or __ Anaerobic 0 02 p o IN CASE Of the n recipe place one or more regenerated catalyst under the catalyst clip on the bottom of the jar lid The catalyst must be regenerated after each incubation by heating it in a hot air oven at 160 C for 30 minutes or 100 C for 60 minutes to dry it thoroughly 3 Close the jar Put the lid on the jar slide the jar clamp over the lid and

Quick installation and user guide

Contents

Download Pdf Manuals

Related Search

Related Contents