View - Miller Camera Support
Contents
1. G is achieved It is recommended to identify this point on the camera as it will be useful in step 2 5 Attach the CAMERA PLATE to the camera or the QUICK RELEASE TRIPOD ADAPTOR and securely tighten the screws Align the CAMERA PLATE with the SLIDING PLATFORM and slide it in until the safety mechanism is engaged Release the SLIDING PLATFORM LOCK and slide the SLIDING PLATFORM such that the camera s C of G is directly above the centre axis of the Fluid Head and tighten the SLIDING PLATFORM LOCK fig 5 If this can not be achieved then reposition the CAMERA PLATE on the Camera or the QUICK RELEASE TRIPOD ADAPTOR step 2 4 This will ensure that the system has maximum stability CofG MILLER Fig 5 Sliding Paltform Sliding Platform Lock Operating Instructions 3 Counterbalance Control The counterbalance system was designed to neutralise the effect of the camera weight when it is tilted The Compass 25 Fluid Head offers a 4 position counterbalance system which can be operated via the COUNTERBALANCE SELECTOR fig 2 The COUNTERBALANCE SELECTOR must be operated when the SLIDING PLATFORM is in a horizontal position After changing the Counterbalance setting it may be necessary to tilt the camera back and forth to ensure that the CB spring has engaged The camera must be held securely while changing the Counterbalance setting 3 1 For safety ensure that Counterbalance position 4 is selected 3 22. Lock Counterbalance System Camera Platform Type Camera Plate Mounting Base Ball Level Range Handle Temperature range Construction Sealing Finish Warranty 2 8 kg 4 0 14 0 kg 20 kg 5 Selectable fluid drag positions O 90 75 Positive Lock caliper brake system 5 Selectable fluid drag positions O 360 Positive Lock caliper brake system 4 Selectable positions see performance graph Sliding platform with 70 mm travel amp quick release Euro Camera Plate 1 4 3 8 and 1 4 Pin Carriage 100 mm Ball Levelling 10 Standard black anodised pan handle with adjustable angle 40 C to 65 C Lightweight diecast Aluminium alloy moulded reinforced plastics Water amp Dust resistant Matt black low sheen durable powder coated with anti corrosive pre treatment 3 Years Technical Data 71 2 8 163 6 4 190 7 5 Operating Instructions The operating instructions are described in six steps Please read and understand these instructions before using this equipment Do not omit any steps Pan Handle Clamp 1 Fluid Head Set up 1 1 Loosen the PAN HANDLE CLAMP fully then rotate the PAN HANDLE until it is approximately perpendicular to TI Ni yy ALI the THREADED STUD fig 3 and tighten the PAN Sp Mu EL lac S HANDLE CLAMP avoid contact wear between the Do NAS serrations on the Fluid Head and the PAN HANDLE SJE FaN Z Illumination Button CLAMP if this
3. Hold the camera and release the TILT LOCK then gently tilt the camera from a horizontal position forward then backward and observe its response If the Camera Springs Back to the horizontal position then a lower Counterbalance setting is required select Counterbalance position 3 and recheck select lower setting again if necessary Correct counterbalance setting has been achieved when minimum effort is required to move the camera over the entire tilt range TIP Fine tuning can be achieved by adjusting the SLIDING PLATFORM see step 2 6 Counterbalance Performance C of G above Camera Plate mm oO Q o nN a o nN So o a o Q o a o o Compass 25 Fluid Head Counterbalance 0 10 12 14 16 18 20 22 24 26 28 30 Camera Payload kg Operating Instructions 4 Pan Tilt Drag Control The Compass 25 Fluid Head offers 5 selectable positions of fluid drag zero setting in the Pan and Tilt The settings are equally stepped from light drag in position 1 up to heavy drag in position 5 the drag plates are completely disengaged in position zero Do not Pan or Tilt the Fluid Head whilst adjusting PAN or TILT DRAG CONTROL or whilst the PAN amp TIL DRAG CONTROL is between settings Tilt Drag Control Counterbalance Selector e The drag setting can be changed at any tilt or pan angle oS ER NEL a 5 Pan Tilt Lock Control a The Compass 25 Fluid Head offers high capa
4. city caliper disc brake N A pes Y j Nadas eae system to hold the Fluid Head in a fixed pan and or tilt position SF fg es Camera position will not change when applying or releasing the Pan A cae SN Le SS Tilt locks 0 Bubble Level Do not pan or tilt the Fluid Head whilst the PAN or the TILT LOCK is partially applied Pan Drag Control 6 Illumination The Compass 25 Fluid Head offers illumination of the BUBBLE Fig 7 LEVEL when the low ambient light conditions exist Illumination can be achieved by pressing the ILLUMINATION BUTTON once The light will switch off after 10 seconds Maintenance The Compass 25 Fluid Head offers high quality surface coatings Miller recommends keeping the Fluid Head clean at all times by using soft brushes and lint free cloth to wipe over the surfaces e Do not immerse the Fluid Head in any liquid e Do not use stiff brushes abrasives harsh detergents and solvents Battery Replacement The Compass 25 Fluid Head uses a single 11A type 6 Volt battery for Illumination Miller recommends the following batteries to provide long life performance GP11A Duracell MN11 or Vinnic L1016 1 Using a Phillips Head 1 screw driver remove the RETAINING SCREW and the BATTERY DOOR 2 Using a small flat screw driver remove the battery 3 Align the new battery as shown on the back of the BATTERY DOOR and place into the BATTERY HOUSING then push down the battery into place A small flat screw dr
5. ie compass tue ys compass 25 Fluid Head OPERATOR S MANUAL 1038 Compass 25 Fluid Head Features and Controls Sliding Platform Lock Pan Handle Clamp Pan Handle Sliding Platform Tilt Lock Pan Lock Threaded Stud Clamp Nut Features and Controls Camera Plate Release Knob Tilt Drag Control Accessory Mounting N Camera Screws Quick Release Knob pi Safety Tab Counterbalance Selector Bubble Level Pan Drag Control Fig 2 Introduction Thank you for purchasing the Compass 25 Fluid Head The Compass 25 Fluid Head has been designed to suit payload capacities from DVCAM to standard configuration ENG cameras The robust design and construction of the Compass 25 Fluid Head offers maximum stability accuracy and durability and includes precision ball bearing mounted Fluid Drag Plate system in the Pan and Tilt assembly to deliver true fluid drag performance over the entire temperature and payload range The Fluid Drag and the Counterbalance system were designed to provide excellent control and repeatability and offer progressive equal increments of drag and torque The Compass 25 Fluid Head also offers Illuminated Bubble level The Compass 25 Fluid Head will give best performance when used on a wide range of Miller tripods including SOLO ENG 1505 2 Stage 402 and Sprinter Il 1576 tripod This will ensure maximum sys
6. iver may be used to push down the battery into the BATTERY HOUSING 4 Align the BATTERY DOOR into the body then tighten the screw lightly Battery Housing Retaining Screw Battery Door Fig 8 10 Illumination Button Battery Storage The Compass 25 Fluid Head can be stored for extended periods Miller recommends storage in a Miller Soft Case and the following e Remove battery e Clean the external surfaces e Keep in a dry place away from direct sunlight e Loosen off PAN amp TILT LOCK SPARE PARTS AND ACCESSORIES ITEM Battery Camera plate Assembly Including 3 8 1 4 screws Camera screw 3 8 Camera screw 1 4 1 4 pin carriage Telescopic Pan Handle assembly including Handle Clamp Telescopic Pan Handle Soft Case Clamp nut Accessory Mounting Bracket Ass y Accessory Mounting Adaptor Ass y WARRANTY Please refer to warranty card for complete details ITEM NO P7715 860 P0037 P0036 493 694 692 876 P3836 1216 1217 11 Service Sales and Support Miller Authorised Service Agents must carry out all service and repair work Failure to observe this requirement may void warranty It is advisable to notify Miller or a Miller Authorised Service Agent if a change of performance is observed as a result of dropping or rough usage For information regarding sales and service of Miller products or for your nearest Miller representative please contact us via ou
7. occurs then unwind the PAN HANDLE D CLAMP further L 1 2 Ensure that the TRIPOD BOWL is approximately A bel ul te ee A horizontal Place the Fluid Head into the TRIPOD Pe ee eS BOWL adjust the BUBBLE LEVEL fig 3 such that De the bubble is inside the black circle and tighten the CLAMP NUT 1 3 Set the initial control settings as follows see Figure 1 amp 2 e Select Counterbalance to position 4 top setting e Select Pan amp Tilt Drag to position 0 e Tighten the PAN LOCK TILT LOCK and the SLIDING PLATFORM LOCK Pan Handle Threaded Stud Clamp Nut Fig 4 2 2 2 3 2 4 2 5 2 6 Operating Instructions Camera Set up Remove the CAMERA PLATE by pulling down the SAFETY TAB while rotating the QUICK RELEASE KNOB to the left The CAMERA PLATE should pop out Refer to the Camera s owners manual for correct method of attachment to the CAMERA PLATE Inspect the CAMERA PLATE and remove the 1 4 and 3 8 screws or the 1 4 PIN CARRIAGE DVCAM mount as required The 1 4 and 3 8 screws can be stored underneath the SLIDING PLATFORM fig 1 Attach camera accessories and the battery to the camera it is recommended to estimate the camera s Centre of Gravity C of G for the purpose of correctly positioning the camera on the CAMERA PLATE The camera s C of G can be estimated by placing the camera on to a round rod and then shifting it backwards or forwards until a balance point C of
8. r website or at the following MILLER CAMERA SUPPORT EQUIPMENT 30 Hotham Parade Artarmon Sydney NSW 2064 Australia Tel 61 2 9439 6377 Fax 61 2 9438 2819 Email sales miller com au MILLER Camera Support LLC USA 218 Little Falls Road Cedar Grove New Jersey 07009 1231 USA Tel 973 857 8300 Fax 973 857 8188 Email sales millertripods us MILLER FLUID HEADS EUROPE LTD Unit 12A Shepperton Business Park Govett Avenue Shepperton Middlesex TW17 8BA United Kingdom Tel 44 0 1243 555255 Fax 44 0 1243 555 001 Email sales millertripods europe com WEBSITE www millertripods com MILLER gt www millertripods com MILLER CAMERA SUPPORT EQUIPMENT 30 Hotham Parade Artarmon Sydney NSW 2064 Australia Tel 61 2 9439 6377 Fax 61 2 9438 2819 Email sales miller com au D7885 1
9. tem stability to suit any professional set up The Compass 25 Fluid Head will suit most industry standard 100 mm tripods as well please refer to manufactures manual for mounting details Safety Instructions Please use this manual to familiarise yourself with the operation of the Compass 25 Fluid Head and observe these instructions to prevent any damage to your equipment Ensure that all equipment is operating correctly and free from defects and damage also please ensure that the tripod is steady secure and that the bowl is approximately horizontal when attaching the camera The operator is responsible for the safe operation of this piece of equipment Do not exceed the maximum payload capacity of the Fluid Head Do not leave the camera unattended on the Fluid Head Do not release the SLIDING PLATFORM LOCK whilst the camera is at an angle Do not adjust the tripod whilst the camera is attached to the Fluid Head Ensure PAN HANDLE CLAMP and CLAMP NUT is securely tightened Apply TILT LOCK when adding removing equipment from the camera or when attaching removing the camera from the Fluid Head Hold camera securely whilst changing Counterbalance Pan Drag or Tilt Drag settings Hold the camera securely whilst releasing the RELEASE KNOB Hold camera securely whilst adjusting the CLAMP NUT to level the Fluid Head Weight Payload Range Max Payload Capacity Tilt Drag Tilt Range Tilt Lock Pan Drag Pan Range Pan
Download Pdf Manuals
Related Search