RISE Electrical User Manual
Contents
1. Fix Kit 5 1 8 x 5 8 Countersunk Wood Screw 2 pcs 93 Silver xx 01 Black 68002509 xx Kneesaver Z Bar 2 pcs for MED Bases 30202284 xx Side Support 1 pcs for EXT Bases 68002403 xx 28 Foot 1 pcs for EXT Bases 68002462 Standard 2 leg Up Down Switch 1 pcs y Fix Kit 3 3 16 x 2 1 8 Countersunk Wood Screw 8 pcs Fix Kit 6 Plastic Round Cap 12 pcs Leg Motor Cable attached to motors 2 pcs QKA Tableclip Plastic Wire Clip 6 pcs 68002462 PS Power Adaptor 1 pc Note The hardware bag may contain extra components Tools Required Phillips Screwdriver M5 Hexagonal Wrench 55750100 Plastic Rectangular End Cap 4 pcs 68002462 PS CABLE Power Cable 1 pc on Electric Drill with Phillips Head Bit N A X Completed Base Examples SML Base MED Base LRG Base Assembly Instructions caution please read notes carefully 1 Attach Feet to Height Adjustable Legs Left Height Adjustable Leg Sub Assembly Position the 2 Height Adjustable Legs making sure the wire cutouts on the Motor Housings are facing each other Using an M5 Hexagonal Wrench attach the Feet to the Height Adjustable Legs with 8 Black M8x16mm Panhead Bolts Make sure the longer sides of the Feet are facing the front as shown in Figure 1 Note Both Height Adjustable Legs are id2. 36 ISE Work Learn Inspire USER MANUAL RISE RISE S2 Height Adjustable Tables with LD Control System ISE Inc 950 Warden Ave Toronto Ontario M1L 4E3 May 2015 Contents 1 IMPORTANT INFORMATION 1 1 IMPORTANT SAFETY INFORMATION 1 2 USER INFORMATION 1 3 BEFORE YOU START 2 ASSEMBLY amp ADJUSTMENT 2 1 ASSEMBLY INSTRUCTIONS 2 2 CONTROL MOUNTING GUIDELINES 2 3 COMMISSIONING 2 4 OPTIONAL CONTROLS 2 5 SYSTEM CONFIGURATION 2 6 ADJUSTMENTS 3 OPERATION INSTRUCTIONS 3 1 CONTROL OPERATION 3 2 SETTING CONTROL POSITIONS 4 MAINTENANCE amp REPAIRS 4 1 CLEANING INSPECTION AND STORAGE 4 2 USER MAINTENANCE INSTRUCTIONS 4 3 REPAIRS 5 APPENDIX 5 1 ASSEMBY ILLUSTRATION 11 11 11 12 12 12 12 12 15 15 16 16 16 16 17 17 1 0 Important Information SAFETY FIRST Your safety and the safety of others is very important And using this product safely is an important responsibility Read all instructions and safety warnings before using the table Keep this user s manual handy so you can refer to it any time To help you make informed decisions about safety we have provided operating procedures and other information on labels and in this user s manual This information alerts you to potential hazards that could hurt you or others Of course it is not practical or possible to warn you about all the hazards associated with operating or maintaining a table You must use your own good j
3. M3 O NOTICE When connecting the motor cables you must strictly adhere to the sequence M1 M2 M3 for connecting the motors A CAUTION Risk of bodily injury During commissioning a system with single end limit switches connection of upper and lower signal limit switches in series or when changing a motor on such a system the motors must not be extended to their highest position upper limit switch active 2 Connect hand switch Plug the hand switch into the 7 pin socket HS o NOTICE you can choose from a wide range of LOGICDATA handswitches for the COMPACTECO control unit Information about available handswitches can be found in the latest product catalogue and on the website www logicdata at 3 Connect optional components If your control unit has an earthing cable lug attach a cable to a metal part of the desk 4 If your control unit has a LogicConnector DATA you can connect accessories like sensors 2 4 Optional Control Mounting guidelines d NOTICE to determine whether the LogicConnector DATA is activated please compare the product name on the nameplate with the order code that is shown in the appropriate datasheet O NOTICE When components like sensors shall be disconnected from the LogicConnector DATA be sure to unlock the 8pin connector on the cable properly There is a fixing hook on this connector that must be pressed 5 Connect mains supply A DANGER GROUNDING INSTRUCTIONS This product mu
4. plugged in the COMPACTeco control unit is operational d NOTICE in case of a mains power breakdown or if the power cord is unplugged during the movement of the drives a manual reset of the COMPACTeco may be necessary 2 5 System configuration example The figure below shows the socket assignment for a configuration example This configuration consists of e 1 COMPACIT e 3 control unit e motors inside the table legs e HSF MDF 4M4 LD hand switch 11 2 6 Adjustments The table control handset and motors are sealed units and have no parts that can be serviced or adjusted by the user In case of failure or unexpected operation or from maintenance control your vendor and arrange for service by a qualified technician 3 0 Operation Instructions To ensure safe operation of the COMPACTeco control unit please observe the following safety instructions A CAUTION Risk of injury and electric shock Keep children away from electric height adjustable desks control units and handswitches Electrical shock hazard A CAUTION Risk of Pinching Moving parts can crush When you change the desktop position Use only with 120VAC especially without using pinch protection you must ensure that no people or objects are located in the hazardous area nor may reach into it Do not exceed the duty cycle See manual for safety instructions o NOTICE In case of a mains power breakdown or if the power c
5. 22 2 68 Intertek Rating 120VAC 60Hz 6A Ne Pi Typical Product Label with Date of Manufacture ROL Ergo Type COMPACT e 3 BOS 650 US S650 55628 J nk ping vision xxx Made in EU Input 120V 60Hz2 5A Output S60VA 24V TAL Duty cycle 2min on 18min off O 13 C FOSS Settings LOG PAR xx paz RevX 11 11 2013 13 05 40 Ser No 900000000000000I Number 63400290 Typical nameplate for the LD Control 1 3 Before you start Make sure that there is nothing blocking the travel of the desk in the space where it will operate Before first use the control unit must register the lowest point of elevation to reset as follows To do this simply lower the table to the lowest position by pressing and holding the Down button Then press and hold the Down button on the handset again and hold it down until the table first moves fractions of an inch downwards and then fractions of an inch back up again The control unit has now registered the lowest elevation and is ready to use 2 0 Assembly amp Adjustment 2 1 Assembly Instruction Assemble the frame according to the enclosed instruction sheet page 10 gh w po AON be Compact control unit a x Motor cable xN e A 2 2 Control Mounting Guidelines A CAUTION The power cord must be unplugged while the compact control unit is being mounted see page 6 Always check desktop thickness against the length of the mounti
6. d with a standard household cleaning solution Never use solvents or abrasive or corrosive compounds Products must be cleaned at regular intervals to remove dust and dirt and inspected for mechanical damage wear and breaks worn out parts must be replaced Unplug the power cord if you do not intend to use the desk for a longer period Do not store table or cables in direct sunlight 4 2 User Maintenance Instructions Products are closed units and require no internal maintenance Legs must be inspected at attachment points wires piston rod cabinet and plugs check that legs function correctly Control boxes and handsets electronics must be inspected at attachment points wires cabinet and plugs Inspect the connections cables cabinet and plugs and check for correct functioning The control box is sealed and maintenance free 4 3 Repairs Check all screws and bolts after the first week of use and tighten screws and bolts where necessary to ensure safe operation of the table If the table cannot be raised or lowered check the cable connection between the control unit and the motor units leg system the handset and the control unit as well as between the control unit and the mains outlet If the table still does not respond the control unit may have triggered the overheating protection or the intermittency protection Please wait for at least nine minutes and try again before proceeding with other measures If a contro
7. desktop height is reached o NOTICE The desktop will continue moving downwards until you release the key or the minimum height is reached 3 2 Advanced functions O NOTICE You can only use the following functions of the COMPACTeco control unit if you have a hand switch with memory position keys and a memory key 3 2 1 Saving a desktop position This function allows you to save a defined desktop height One desktop height can be saved per memory position key To save a position proceed as follows o NOTICE if you are switching on the COMPACTeco control unit for the first time all the saved positions are set to the lowest desktop height minimum desktop position 1 Adjust the desktop to the position you want to save A gt 2 The display will show the desktop height e g 73cm gum Li id 2 13 3 Press the memory key 4 The display will read S 5 Press the required memory position key e g 2 6 The display will read S 2 The set desktop position will now be saved to the selected memory position iz key i 7 You will hear an audible double click and after about 2 seconds the saved desktop position will be displayed O NOTICE using saved desktop positions is only available for hand switches with memory keys The design of the memory position keys varies depending on the hand switch model used o NOTICE itis software parameter dependent which motor group can save recall memory pos
8. efore using table A DAN G E R To reduce the risk of electric shock 1 Always unplug this furnishing from the electrical outlet before cleaning A WARN NG To reduce the risk of burns fire electric shock or injury to persons Unplug from outlet before putting on or taking off parts Close supervision is necessary when this furnishing is used by or near children invalids or disabled persons Use this furnishing only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer Never operate this furnishing if it has a damaged cord or plug if it is not working properly if it has been dropped or damaged or dropped into water Return the furnishing to a service center for examination and repair Keep the cord away from heated surfaces Never operate the furnishing with the air openings blocked Keep the air openings free of lint hair and the like Never drop or insert any object into any opening Do not use outdoors Do not operate where aerosol Spray products are being used or where oxygen is being administered 10 To disconnect turn all controls to the off position then remove plug from outlet A WARNING risk of Electric Shock 1 Connect this furnishing to a properly grounded outlet only See Grounding Instructions For loading always put heavier items at the bottom and not near the top in order to help prevent the possibility of the furnishing t
9. entical Longer side of the Feet to be N at the front of the desk If casters are required unscrew the glides on each Foot and firmly screw casters Baci Maze IG ii pa Panhead Bolts TA et Right Height Adjustable Leg Sub Assembly Figure 1 Attach Feet to Height Adjustable Legs 2 Adjust Adjustable Bar Width Using an M5 Hexagonal Wrench loosen the 4 Center Bolts Guiding hole for symmetrical Expand or retract the Adjustable Bar to the desired width while making sure the top holes of the Outer Square Tube align with the holes of the Inner Channel Adjustable Bar XN Use the Center Hole of the Inner Channel as guide for symmetry After achieving the desired width tighten the 4 Center Bolts to secure the Adjustable Bar subassembly See Figure 2 Make sure all 4 holes on the Outer Square Tube align with the 4 holes of the Inner Channel Figure 2 Adjust Adjustable Bar Width 3 Attach Adjustable Bar to Motor Housings Facing the rear of the Height Adjustable Leg Assemblies use an M5 Hexagonal Wrench to fasten the Adjustable Bar with the 4 Silver M8x25mm Countersunk bolts onto the rear of the Motor Housings Make sure to use the 2 outer holes on each end of the Adjustable Bar The 4 Center Bolts of the Adjustable Bar should be facing forward towards the Motor Housings After fastening the Adjustable Bar install the 2 Rectangular Plastic End Caps on each end of the Adjustable Bar See F
10. igure 3 7 Figure 3 Attach Adjustable Bar to Motor Housings 4a For SML Bases Attach Side Supports Install the two Side Supports with the 4 M8x25mm Countersunk Bolts onto the outside of the Left and Right Motor Housings FAN gt N ce SE y Figure 4 Install Side Supports 4b For MED Bases Attach the Kneesaver Z Bars Position the Sub Assembly upright and face the front The Adjustable Bar should be in the rear Loosen the 4 Adjusting Bolts in the middle of the Adjustable Bar while making sure to not change the width alignment performed earlier Locate the slotted end of each Kneesaver Z Bar and slide it between the Adjustable Bar and the back of the Adjusting bolts Tighten the bolts to secure the Kneesaver Z Bars to the Adjustable Bar Note Both Kneesaver Z Bars are identical See Figure 4 Loosen Adjusting Bolts to allow installation of Kneesaver Z Bars and tighten back after positioning DETAIL A Figure 5 Attach Kneesaver Z Bars to Adjustable Bar After the Kneesaver Z Bars have been fastened to the Adjustable Bar fasten the other ends of the Kneesaver Z Bars to the front of the Motor Housings using the 4 Silver M8x25mm Countersunk bolts Install the 2 Rectangular Plastic End Caps See Figure 6 Silver M8 x 25mm Countersunk Bolts Install the 8 Plastic Round Caps on the front of the Kneesaver Z Bars See Figure 7 Install 6 Plastic Round Caps on the back of the Adjustable Ba
11. ipping over A WARNING Risk of Injury to Persons 1 Do not use this furnishing to support video equipment such as televisions or computer monitors Maximum intended load for surface is 220 pounds 100 kilograms without a worksurface and 164 pounds 74 kilograms with a worksurface A DAN G ER Risk of electric shock injury or death 1 Improper usage abuse or misuse of the LOGICDATA COMPACT control unit hand switch motors and other electrical components may result in an electrical shock injury or possible death Do not open the LOGICDATA COMPACT control unit or hand set under any circumstances The control unit and hand switch contain no serviceable parts 10 11 12 13 14 Do not modify or make any changes to the control unit the controls or hand switch During installation repair cleaning or maintenance work the power cable must be disconnected from the outlet The COMPACT control unit is not designed for continuous operation Changing the desktop position without interruption must not exceed the duty cycle indicated on the nameplate The unit is thermally protected and will shut down if use is excessive Allow a 10 minute cooling period for the control unit to reset The COMPACT control unit may only be operated with mains voltage as specified on the nameplate COMPACT control units are also available for the mains voltages used in other countries Only use the power cord supplied with the c
12. itions If both motor groups are capable of saving memory positions the current position of both groups will be stored even if they are different When recalling a stored position in this case both groups start their movement at the same time even if their movement direction is different 3 2 2 Adjusting the desktop to a saved position You can use this function to adjust the desktop to a saved height To change to a saved position proceed as follows O NOTICE availability of the double click function depends on the software configuration of the control unit Option A without double click function 1 Press the required memory position key e g 2 and hold it down The T 2 desktop will move until it reaches the saved position If you release the key before the saved position is reached the desktop will stop and the saved desktop position will not be reached k 2 The desktop has reached the saved position Now release the memory position key The display will read the current saved desktop position Option B with double click function me 14 1 Double click the required memory position key e g click twice and release gt 2 After the double click the desktop will automatically adjust to the saved ine position The display will show the current saved desktop position geil A CAUTION Risk of Pinching When you change the desktop position automatically especially without using pinch pro
13. l unit is replaced it must first be reset before it can be used To do this follow these steps 1 Lower the table to its lowest position by holding the Down button on the handset 2 Press the Down button on the handset again and hold it down until the table first moves fractions of an inch downwards and then fractions of an inch back up again The control unit has now registered the lowest elevation and is ready to use Should the table still not work as intended after taking these measures please contact your vendor for further assistance For instructions on the installation and care of the desktop please follow the instructions from the manufacturer 16 5 0 Appendix 5 1 Assembly Instructions UPDATED a6 S E OCTOBER 10 2013 Work Learn Inspire Part List caution only use the parts and hardware provided 68002348 xx Height Adjustable Leg 2 pcs RISE Glide attached to feet 4 pcs La ann VA q N k y PTA 68000363 xx 19 Foot 1 pcs for EXT Bases Fix Kit 1 M8 x 16mm Panhead Bolt Black 8 pcs Fix Kit 4 3 16 x 3 4 Panhead Wood Screw 6 pcs 68002547 xx 29 45 or 54006700 xx 44 75 or 68002513 xx 76 90 Adjustable Bar 1 pc 2pcs for LRG Bases Fi oj re di Ji 68001089 xx Side Support 2 pcs for SML Bases 68002505 xx 23 Foot 2 pcs Fix Kit 2 M8 x 25mm Countersunk Bolt Silver 8 pcs
14. nch points when the desktop is moving 11 This table is not intended for use by individuals including children with limited physical sensory or mental abilities or with a lack of experience and or lack of expertise unless they are supervised by a person responsible for their safety or have received instructions from that person on how to use the control unit 12 Children must be supervised at all times to ensure that they do not play with the control unit 13 The table may not be used to lift people Do not sit or stand on a table while it is be raised or lowered 14 The table must not be structurally or technically altered or modified in any way 1 2 User Information This Leg System is rated for Commerical Use Only and is rated for a maximum load of 220 pounds 100 kilograms without a worksurface and 164 pounds 74 kilograms with a worksurface The motors may only be used continuously for 1 minute at a time after which they must be left inactive for nine minutes before they can be used again The control unit regulates this automatically FOR COMMERCIAL USE ONLY N WARNING Risk of injury Maximum Load 220 Ibs 100 kg Do notoperate this equipment unless properly trained POUR USAGE COMMERCIAL SEULEMENT AVERTISSEMENT Risque deblessure Charge maximale 100 kg 220 livres Ne pas utilisercet appareil sans formation ISE INC TYPE RISE RS2 fus DATE 0000 00 use Conforms to UL Std 962 Certified to CSA Standard C
15. ng screws before mounting the desktop to ensure they are appropriate and not long enough to protrude through the top surface once screwed in Mount the compact control unit on the underside of the desktop by using these two holes Connect the two motor cables and the cable from the handset to the control unit Take care to route all cables so that they cannot be damaged by normal operation Please refer to the assembly instructions for this and use the supplied cable routing materials to secure the cables Motor soc at t M11 Motor socket 2 Mie Motor socat 3 My gt Hardswtch sockel 43 H Mara ochal F Functional oam cable ua for earthing Tw dosk rame 6 200 Smm hug D Logic Connector DATA tor sornsors and cascadno D NOTICE the clamp next to the mains socket is used as a connector for a functional earth This clamp is used for example to deflect electrostatic charge from the electric height adjustable desk The connector cannot carry out the function of a protective conductor The clamp is also marked with the grounding symbol on top of the housing Grounding Symbol 2 3 Commissioning procedure A CAUTION Risk of electrical shock The power cord must be unplugged while the control unit is being commissioned This table is equipped with a LogicData COMPACTeco control unit to setup the control proceed as follows 1 Connect drive Plug the motor cables into the relevant 8 pin motor sockets in order of M1 M2 and
16. of injury risk that can be predicted Where there exists a risk of squeezing fingers use at least a 1 5 inches safety margin and for body or head especially where children may be present use a minimum of 16 inches 3 During the lowering or raising of the desktop the operator must ensure that no person or object risk being harmed by the operation Under no This tag should be removed circumstances place your fingers on desk legs ine nak sauce theres aan dani while operating desk upwards or downwards epennted produet phones review the user manasi prior to operating The manual may be located under the work surface 4 This tag should be put on the desktop after assembly by the installer 5 Keep children away from moving parts and underneath the desk 6 The table is only to be used as a desk or work surface which allows the user stepless adjustment of the desktop between sitting and standing positions 7 The table must only be operated while in an upright position and must under no circumstances be operated while upside down 8 The table must not be overloaded The maximum allowable load is shown on the nameplate 9 The table must be operated in a dry enclosed space such as an office or similar never outdoors 10 The table is equipped with Intelligent System Protection ISP In the event of a fault motor or component the desktop may move slightly before the safety feature is engaged Stay clear of pi
17. ontrol unit Check that it is not damaged Do not ever operate the COMPACT control unit if the power cord is damaged Before connecting and disconnecting the hand switch you must unplug the power cord otherwise you may damage the hand switch Connect the control unit to a properly grounded outlet only See Grounding Instructions for more information To disconnect turn all controls to the off position then remove plug from outlet In the event of a malfunction e g if the control unit keeps adjusting the desk because a movement key has jammed please unplug the unit immediately Do not expose the COMPACT control unit to water or other liquids including moisture drips splashes or spills Clean the control unit only with a dry cloth Do not operate the COMPACT control unit in a potentially explosive atmosphere Do not operate where aerosol spray products are being used or where oxygen is being administered Do not use the desk with it has been dropped or damaged Contact the manufacturer for examination or repair It is not allowed to connect self constructed products to LOGICDATA COMPACT control units To prevent damage of the control unit use only components suitable for LOGICDATA motor controls A WARNING Risk of injury or death 1 During the raising or lowering of the table there exists a risk of squeezing or pinching between the moving desktop and fixed objects The necessary safety margins depend on the greatest type
18. ord is plugged off during the movement of the drives a manual reset of the COMPACTeco may be necessary O NOTICE The control unit might be damaged by power surges Unplug the power cord during a thunderstorm or if you do not intend to use the desk for a longer period 3 1 Basic functions The COMPACTeco control unit offers an extensive range of functions The availability of some functions depends however on the hand switch that is used with it This section describes the basic functions available with every handswitch designed for use with COMPACTECO control units O NOTICE You must read the user manual carefully before installing or operating the COMPACT control unit ey NOTICE The 2 basic functions upward and 12 downward movement are available for both motor groups separately Please read the manual of the hand switch to see which buttons are linked to which motor group 3 1 1 Upward desktop movement This function enables you to adjust the desktop upwards To change its position proceed as follows Press the desktop up key A Keep pressing the key until the required desktop height is reached D NOTICE The desktop will continue moving upwards until you release the key or the maximum height is reached 3 1 2 Downward desktop movement This function enables you to adjust the desktop downwards To change its position proceed as follows Press the desktop down key v Keep pressing the key until the required
19. r See Figure 8 Figure 6 Attach Kneesaver Z Bars to front of Motor Housings Plastic Round Caps Figure 7 Attach Plastic Round Caps to front of Kneesaver Z Bars Figure 8 Attach Plastic Round Caps to back of Adjustable Bar 4c For LRG Bases Install Front Adjustable Crossbar Facing the front of the Height Adjustable Leg Assemblies use an M5 Hexagonal Wrench to fasten the Adjustable Bar with the 4 Silver M8x25mm Countersunk bolts onto the front of the Motor Housings Make sure to use the 2 outer holes on each end of the Adjustable Bar The 4 Center Bolts of the Adjustable Bar should be facing forward towards the Motor Housings After fastening the Adjustable Bar install the 2 Rectangular Plastic End Caps on each end of the Adjustable Bar See Figure 9 o a a aD Use Outer 2 holes PP Ze Rectangular Plastic End Caps N N N X Q N Q Q a N A T RS N Front of Motor Housing Figure 9 Attach Adjustable Bar to Motor Housings 4d For 2 Leg EXT Bases Install Side Support and Feet e N M8 amp x16MM Panhead Bolts 3 8 N N M38x25MM Countersunk Bolt N N N N 3403 29 Foot 68002403XX Install the 19 foot and the 29 foot using the M8x16 Panhead Bolts suppllied The 29 foot 68002403XX should always be installed on the same leg as the Side Support 30202284XX on the side with the extended co
20. rner Install the Side Support 30202284XX with the 2 M8x25MM Countersunk Bolts onto the side of the Motor Housing 5 Check Motor Position Ensure motor is properly positioned into the motor housing Ensure motor cable strain relief is positioned in the motor housing cut out Ensure all motor connectors are properly connected Connectors Strain Relief Motor Motor Housing 6 Install the Worksurface Place the Worksurface on the floor with the bottom facing up Make sure to lay it on a protective layer to prevent scratching Using a tape measure position the frame so that the distance between the back edge of the Worksurface is 3 away from the back of the Adjustable Bar Depending on the size of the Worksurface selected ensure to leave equal distances on both sides of the frame Using an Electrical Drill with a Phillips Bit fasten the frame onto the Worksurface with the 3 16 x 2 1 8 Countersunk Wood Screws See Figure 10 3 16 x 2 1 8 Countersunk Wood Screws Figure 10 Install the Worksurface
21. st be grounded If it should malfunction or breakdown grounding provides a path of least resistance for electric current to reduce the risk of electric shock This product i equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances A DANGER RISK OF ELECTRICAL SHOCK Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded Do not modify the plug provided with the product if it will not fit the outlet have a proper outlet installed by a qualified electrician This product is for use on a nominal 120 volt circuit and has a grounding plug that looks like the plug illustrated below Make sure that the product is connected to an outlet having the same configuration as the plug No adapter should be used with this product 10 This leg system is equipped is a NEMA 5 15 type plug as shown above and must be plugged into a grounded outlet A CAUTION Risk of electrical shock Before you plug in the power cord check the following again e The mains supply voltage must be as specified on the type plate All the components must be plugged into the right sockets The earthing cable must be connected e When the power cord is
22. tection you must ensure that no people or objects are located in the hazardous area or may reach into it O NOTICE If you press another key while the desktop is changing automatically to a saved position it will stop immediately You then have to reactivate automatic desktop adjustment to a preset position 3 2 3 Manual Reset When the actual desktop position no longer corresponds to the height displayed or you wish to use a configured control unit on another identical electric height adjustable desk you have to reset the lowest desktop position to the minimum height v 1 Press the desktop down key Keep pressing it until the desktop has reached the lowest position programmed desktop position W 2 Press the desktop down key again and keep pressing It After about 5 seconds the desktop will slowly move further down until it reaches the absolute lowest desktop position possible 3 Release the desktop down key The electric height adjustable desk can now be used again normally A CAUTION Risk of Pinching The intelligent system protection ISP is not enabled during all resets and limit position calibration DD NOTICE This function is available for both motor groups separately Please read the manual of the used hand switch to see which buttons are linked to which motor group 15 4 Maintenance amp Repairs 4 1 Cleaning Inspection and Storage Clean the frame by wiping it down with a microfibre cloth moistene
23. udgment You will find important safety information in a variety of forms Safety Messages preceded by a safety alert symbol A and one of three signal words DANGER WARNING or CAUTION These safety messages are listed in order of severity identify the general risks and what actions you are to take to avoid the risks These signal words mean A DANGER Indicates an imminently hazardous situation which if not avoided will result in serious injury or death This signal word is limited to the most extreme situations A WARNING Indicates a potentially hazardous situation that if not avoided could result in serious injury or death A CAUTION Indicates a potentially hazardous situation that if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices d NOTICE Indicates an alert to call attention to proper assembly instructions or particular operation procedures to assure correct equipment function and to avoid equipment damage or wear The information and specifications included in this publication were in effect at the time of approval for printing ISE reserves the right to discontinue or change specifications or design at anytime without notice and without incurring any obligation whatever 1 1 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS When using an electrical furnishing basic precautions should always be followed including the following Read all instructions b
Download Pdf Manuals
Related Search