USER MANUAL
Contents
1. b CZFATITYIEFAFA Camddns service DONS Setting Enabled Disabled Provider ddns camddns com v State Hote 1 5chedule Update Feature of DDHS schedule update is designed for IP products which installed behind the ICS or HAT devices Update range from every 5 minutes to 5000 minutes and 0 remain to off 2 Please note that the hostname will be blocked by DynDHS org if schedule update more than once every 5 minutes to 60 minutes In general schedule update in every 1440 minutes is recommended 1 Please enable this service 2 Key in user name Schedule update is default at 5 minutes 4 Click Apply DDNS Status 1 Updating Information update 2 Idle Stop service 3 DDNS registration successful can now log by http lt username gt ddns camddns com Register successfully 4 Update Failed the name is already registered The user name has already been used Please change it 5 Update Failed please check your internet connection Network connection failed 6 Update Failed please check the account information you provide The server user name and password may be wrong 28 46 v Server Setting There are three choices of server types available Email FTP and SAMBA Select the item to display the detailed configuration options You can configure either one or all of them Server Settings Mail Setting Login Metho2. 128MB Intel C 2 8G RAM 512MB Graphic card 64MB 6 46 11 Product Installation A Monitor Setting l Hight Click on the desktop Select Properties Arrange Icons Refresh Save As Scheme Graphics Options Display Modes Mew gt Display Plug and Play Monitor on Intel R 82915G GV 910GL Express Chipset Family Screen resolution Less 4 V 1024 by 768 pixels 7 46 CZFATITYIEFAFA Hardware Installation Assignment Camera Construction Please refer to the picture for camera installation Use the screws to lock the bracket to the wall or ceiling and then connect the camera to the bracket There s a knob on the back of the bracket Loosen the knob and you can adjust the angle of camera Tighten it to fix the angle fix the camera Loosen to adjust the angal of camera Tighten to fix it Q n Tighten the joint Lock the screw li Connect power adaptor Connect IP Cam to PC or network with Ethernet cable oet up the network configurations according to the network environment For further explanation please refer to chapter Network Configuration for IP CAMERA e 8 46 ii PoE Power Over Ethernet Optional 802 3af 15 4W PoE Switch is recommended Power over Ethernet PoE is a technology that integrates power into a standard LAN infrastructur
3. Best High Standard Medium Low The higher the quality is the bigger the file size is Also not good for internet transmitting 35 46 3 Video Frame Rate The video refreshing rate second 4 Video Format H 264 MPEG4 or 5 HISP Path RTSP output connecting route e 3GPP Streaming mode JGPP Streaming Setting Q Enabled Disabled Resnlutian 1765x144 FPS 45 Format MPEG4 Path exrtspi 3 Ho Audio 3GPP mode suggested setting 176x144 resolution 5 MPEG4 format 1 Enable or Disable 3GPP Streaming 2 3GPP 3GPP output name ii Audio IP CAMERA supports 2 way audio User can send audio from IP Camera Built in mic to remote PC User can also send audio from remote PC to IP Camera s external speaker a Audio from IP camera built in mic to local PC select Enable to start this function and also can select the audio type Audio IP Camera to PC Enabled Disabled Audio Type 6 711 64K bps Adjust Volume Audio from local PC to IP Camera Check chatting in the browsing page 36 46 CAMERA 201 VDEC 01 14 54 10 Size 1280x800 FPS 25 default Streaming 1 v Online Visitor 1 Relay Out OON OFF The Audio will not be smooth when enable SD card recording function simultaneously 3 46 CAMERA D Event
4. Netmask 255 255 255 0 Gateway 192 168 1 254 DNS 1 168 95 1 1 DNS 2 168 95 192 1 80 00 0 00 00 21 0 Search Device ge Device Name IP address and Gateway 1 Select the device on the left side 2 Change network parameter on the right side 3 Press Submit button Press earch Device to re sea 5 Double click the device to open it xi Then please key in the default user name admin and password admin Connect to 192 168 1 217 2 1 IP Camera User name admin Password Remember my password Install ActiveX control For the first time to view the camera video via IE it will ask you to install the ActiveX component 2 Camera Windows Internet Explorer Oc tte i192 168 1 135 File Edit View Favorites Tools Help amp Camera gt B v EN English United States Ej To 7 This website wants to install the Following add on VEBWATCH2 cab From video System co LEd IF you trust the website and the add on and want to install it click here D Click here to install the following Activex control WEBW ATCH2 cab from Video System Ltd If the installation failed please check the security setting for the IE browser IE gt Tools gt Internet Options gt Security Tab gt Custom Level gt Security Settings Download unsigned ActiveX contro
5. 10 INSTAITEJACTIVEX CONTROL 12 ENVE Seep eaten 14 CONFIGURAT 8 eee 16 SBISTENL MM M 17 NETA ORE 20 32 il CALOR ee ee 38 NETWORK 2 5 2 5 lt 5 2 lt lt 2 43 FACTORY 5 A Aaa 45 PACKAGE CONTENT E 45 MICRO SD CARD oA 46 V1 1 120515 3 46 Preface This is a 1 2 7 2M CMOS IP camera with the web server built in User can view real time video via IE browser It Supports H 264 JPEG and MPEG4 video compression which provides smooth and high video quality The video can be stored in the Micro SD card and playback remotely With user friendly interface it is an easy to use IP camera which is designed for security application Il Product Specifications 1 2 7 2M CMOS Sensor Digital Noise Reduction Digital Wide Dynamic Range Shutter Speed adjustion sense Up adjustion Power over Ethernet available Option H 264 JPEG MPEG4 compression Micro SD card backup DI DO Support iPhone Android Symbian Blackberry Mac Triple Streaming SDK for Software Integration Free Bundle 36 Channel Recording Software Specificati
6. Micro SD card before use it Make sure pushing Micro SD card into the slot completely Click the date listed this page and it shows the list of the video The video format is AVI Click the video to start Microsoft Media Player to play it To delete the video check it then click Del Time Video Event Type 09 05 22 090522T avi Hetwork Dis connected 09 05 52 090552f avi Hetwork Dis connected 09 06 22 030622f avi Hetwark Dis connected 03 06 52 090652f avi Hetwork Dis connected 03 07 22 0907 22f avi Hetwork Dis connected 09 07 52 030752f avi Hetwork Dis connected 09 08 22 090822f avi Hetwork Dis connected 03 08 51 090851f avi Hetwark Dis connected 09 09 21 090921f avi Hetwork Dis connected 09 09 54 0905951f avi Hetwork Dis connected 123415 SD Management Choose The 1st day means the recoding file will be keep one day Example It is five o clock now Choose The 1st day The files will be kept from five o clock yesterday to five o clock today No SD card SD Management Auto Deletion Off Y Keep 1 2 3 4 days Off The 1st day The 2nd day The 3rd day The 4th day The 5th da The 7th day The 8th day The 9th day The 10th day The 15th day The 20th day The 25th day The 30th day 42 46 ere VI Network Configuration Configuration 1 x ADSL Modem Internet Real IP Internet Access ADSL or Cable Modem IP address One real IP or
7. Settings Settings r Disable Enable Prompt m Download unsigned Activex controls Disable Enable Prompt 19 Initialize and script ActiveX controls not marked as safe Disable Enable Run ActiveX controls and plug ins Administrator approved ewok in Reset custom settings Reset to Medium When popup the following dialogue box click Yes Are you sure you want to change the security settings for this zone CAMERA IV Live Video Start a IE browser type the IP address of the IP camera in the address field It will show the following dialogue box Key in the user name and password The default user name and password are admin and admin Connect to 197 168 1 217 Camera User admin Password mm Remember my password When connect to the IP CAMERA The following program interface shows VANS LS 201 14 54 10 5 1280 800 FPS 25 defaut v Streaming1 v Chatting Online Visitor 1 Relay Out OFF Q 14 46 i 1 QD Get into the administration page Video Snapshot 3 Show system time video resolution and video refreshing rate 4 Select video streaming source When streaming 2 setting in Video Setting is closed this function will not display 5 IP Camera supports 2 way audio Click the Chatting check box Th
8. one dynamic IP Only IP CAMERA connects to the internet For fixed real IP set up the IP into IP CAMERA For dynamic IP start PPPoE Configuration 2 Q D Switch Hub ADSL Modem Internet Internet Access ADSL or Cable Modem IP address More than one real IP or one dynamic IP IP CAMERA and PC connect to the internet Device needed Switch Hub For fixed real IP set up the IP into IP CAMERA and PC For dynamic IP start PPPOE gt 43 46 uere ii Configuration 3 31 5 Virtual IP Sharing ADSL Modem Internet Internet Access ADSL or Cable Modem address one real IP or one dynamic IP CAMERA and PC connect to the internet Device needed IP sharing Use virtual IP set up port forwarding in IP sharing Xe gt 44 46 CAMERA Vil Factory Default i To recover the default IP address and password please follow the following steps Remove power and press and hold the button in the back of IP CAMERA iii gt Power on the camera Don t release the button during the system booting iv It will take around 30 seconds to boot the camera v Release the button when camera finishes proceed vi Re login the camera using the default IP http 192 168 1 200 and user name admin password admin Vill Package contents i IP CAMERA Network Camera ii gt Adaptor iii gt CD title User manual IP installati
9. uses Ad hoc mode Wireless Setting MAC Address 00 11 2 03 37 48 Ad hoc Operation Mode Auto SID Default Channet G Security Hone 2 550 Based on AP setting 3 Channel This is only be used when the user selects Ad hoc mode in order to avoid conflict 4 Security supports None WEP WPA PSK security encryption based on the setting of the Router 5 WEP 30 46 WEP Setting Authentication Open System Encryption Key Type 10 character max Key 1 Key 2 Key 3 Key 4 Authentication There are Open System and Shared Keys itis based on different encryptions This has to be the same as the Router s setting Encryption The length of key is decided here In the 64bit encryption the HEX key should include 10 characters while ASCII key includes 5 characters In the 128bit encryption the HEX key should include 26 characters while ASCII key includes 13 characters Key Type There are HEX and ASCII When HEX is selected user only can key in hexadecimal characters 0 9 A F a f If ASCII is selected user can key any alphabet letter and number as the key Key 1 4 Type the key here The length and type of the key have to match your settings above 6 WPA PSK Security WPA PSK WPA PSK Setting Encryption TKIP Pre Shared Key ASCII format 8 63 Encryption There are TKIP and AES e Pre Shared Key Allow a
10. uses RTSP Start and End Multicast Setting Based on the RTSP Server 21 46 Multicast is a bandwidth conservation technology This function allow several user to share the same packet sent from IP camera To use Multicast appoint IP Address and port here TTL means the life time of packet The larger the value is the more user can receive the packet To use Multicast be sure to enable the function Receive Multicast in your media player g ONVIF Choose your ONVIF version and settings Bonjour Bonjour Enabled Disabled Bonjour Name 000 0 00 00 28 88 LLTD Link Layer Topology Discovery LLTD Enabled Disabled h Bonjour This function enable MAC systems to link to this IP camera Key in the name here l LLTD If your PC supports LLTD enable this function then you can check the connection status properties and device position like IP address of this IP Camera in the network map Enable or disable RTSP server first and can setup RTSP port and the start and end port of RTP ii Advanced a Https Hypertext Transfer Protocol Secure Https can help protect streaming data transmission over the internal on the higher security level Created Request Subject Date Installed Certificate Subject Date Connection Types Http amp Https 22 46 CAMERA Https setting Before setting new request please remove old
11. CAMERA User Manual IP CAMERA uere WARINGS TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MISTURE DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL COPYRIGHT THE TRADEMARKS MENTIONED IN THE MANUAL ARE LEGALLY REGISTERED TO THEIR RESPECTIVE COMPANIES 2 46 ere GO Ww p GO gt Vi VII VIII Content 4 PRODUCT 4 PRODUCT 7 MONITOR SETTING dos dieaedetusmnt diesen 7 HARDWARE INSTALLATION ASSIGNMENT cccceccscosccccecceccecceccececceccscceceecesceccsccecesceccscscaecesseccscseceseesacs 8 PA ENT
12. List IP CAMERA provides multiple event settings i Event Setting Motion Detection Area Setting E mait FTP 5 to SD card Samba E mait FTP to SD card Samba E mait FTP to 50 Samba Camera Warning a period of time between every two motions detected O Based on the schedule AVI File with Record Time Setting Record Time Setting Pre Alarm Post Alarm Network Dis connected Dis connected Save to SD card Network IP Check IP Check O Enabled Disabled www google com E Save to SD card a Motion Detection IP CAMERA allows 3 areas motion detection When motion is triggered it can send the video to some specific mail addresses transmit the video to remote ftp server trigger the relay and save video to local Micro SD card To set up the motion area click Area Setting Using mouse to drag and draw the area The same operation for area 2 and 3 b Record File Setting IP CAMERA allows 3 different types of recording file to change its record size When motion alarm is triggered there are 3 different types of record mode 38 46 CAMERA 1 AVI File With Record File Setting 2 Multi JPEG With Record File Setting only with JPEG compression format 3 Single JPEG Single File with Interval Setting Record Time Setting Pre Alarm and Post Alarm setup
13. bled Disabled Text Edit Time Setting Network Server Time 2011424 15 2 24 Time Zone GMT 08 00 Date Format yyimmidd mmddyy ddimmiyy Time Zone 08 00 Enable Daylight Saving mP HTP Server 198 123 30 132 Update 6 b Hour Shift Minutes 1440 1440 O Synchronize with PC s time Date 2011 124 Time 14 59 39 Manual Date 20111241 Time 14 59 14 The date and time remain the same 16 46 CAMERA A System i System Information a Server Information Set up the camera name select language and set up the camera time 1 Server Name This is the Camera name This name will show on the IP Installer 2 Select language There are English Traditional Chinese and Simplified Chinese to select When change it will show the following dialogue box for the confirmation of changing language Microsoft Internet Explorer 2 Change Language you sure b OSD Setting Select a position where date amp time stamp text showing on screen OSD Setting Time Stamp Enabled Disabled Text Enabled Disabled Tes m Moreover click Text Edit can entry to adjust the OSD contents which is including Size and Alpha of text Finally click Upgrade button to reserve the setting C server time setting Select options to set up time NTP Synchronize wi
14. d Account Mail Server Username Password Sender s Mail Mail Mail Port 25 Default 25 Secure Connect TLS SSL FIP Setting FIP Server Username Password Port 21 Path j Mode PORT Create the folder Tes ex Pathi 20100115 7121032m avi Samba Network storage Location ip falder Workgroup Username Password Create the folder Tes ex Pathi201001157121032m avi vi Wireless Setting Wireless Network Optional 802 11 b g wireless connection Notice Wireless network and Ethernet network use the same IP the user has to unplug Ethernet cable if Ethernet cable is not unplug wireless setting can not be executed 29 46 Wireless Setting Status of Wireless Networks SSID Mode Security Signal strength allan Infrastructure WPA 0 RHOSON Infrastructure WEP 16 Link Infrastructure 16 SinoStar Infrastructure WEP 11 ff 2 Infrastructure WEP 12 00160159 7 Infrastructure WEP 56 RDTEST Infrastructure WEP 48 J3Com Infrastructure 43 Default Infrastructure WPA 74 Wireless Setting Address 00 16 16 16 00 E1 Mode Infrastructure Operation Mode Auto SSID Security a Status of Wireless Networks scan all wireless services b Wireless Setting 1 Mode There are Infrastructure and Ad hoc Infrastructure is for connecting with the router Ad hoc is for connecting with PC There is Channel to select only when user
15. d range for user to set the IP address 24 46 IP ADDRESS FILTER Setting Enable address filter 4 Setting 9 allow deny single address single range Ho Address Filter 1 j e m e L Allow admin ip address always access this device Admin ip address QoS DSCP Quality of Server Differentiated Services Code point DSCP specifies a simple mechanism for classifying and managing network traffic and provide QoS on IP networks DSCP is a 6 bit in the IP header for packet classification purpose Please define the reserve for Live Stream Event Alarm and Management QoS DSCP Setting M Enable QoS DSCP Live Stream Event Alarm Management IEEE 802 1x IEEE 802 1x is an IEEE standard for port based Network Access Control It provides an authentication mechanism to device wishing to attach to a LAN or WLAN The EAPOL protocol support service identification and optional point to point encryption over the local LAN segment 25 46 CAMERA E ESL 3 Authenticator switch Please check what version of the authenticator and authentication server support This camera supports EAP TLS method Please enter ID passwoard issued by the CA then upload related certificates IEEE 802 1x Setting Enable IEEE 802 1x Eapol version Identity Private key password certificate Status Clie
16. e It enables power to be provided to the network device such as an IP phone or a network camera using the same cable as that used for network connection It eliminates the need for power outlets at the camera locations and enables easier application of uninterruptible power supplies UPS to ensure 24 hours a day 7 days a week operation Ethernet g LES PoE Switch Ethernet Cable Ethernet Cable la PoE IP Camera 9 46 CAMERA IP Assignment l Use the software IP Installer to assign the IP address of IP CAMERA The software is in the attached software CD ii IP installer supports two languages a IPinstallerCht exe Chinese version b IPinstallerEng exe English version iii There are 3 kinds of IP configuration a Fixed IP Public IP or Virtual IP b DHCP Dynamic IP c Dial up PPPoE IV Execute IP Installer For Windows SP2 user it may popup the following message box Please click Unblock Windows Security Alert 1 help protect your computer Windows Firewall has blocked some features of this program Do you want to keep blocking this program Q V2 1 Network Device Scan Publisher Unknown Keep Blocking Unblock Ask Me Later Windows Firewall has blocked this program from accepting connections from the Internet or a network If you recognize the program or trust th
17. e publisher you can unblock it When should unblock a program vi IP Installer configuration IP Installer 92 2 Device lists i Address Static DHCP IP Camera 192 168 001 200 Nane IP Camera 0 168 Netmask Gateway DNS 1 DNS 2 Porti MAC 00 0 0 20 08 5 Search Device To Change Device Name IP address and Gateway 1 Select the device on the left side 2 Change network parameter on the right side 3 Press Submit button 4 Press Search Device to re search again 5 Double click the device to open it Vil IP Installer will search all IP Cameras connected on Lan The user can 10 46 viii X CAMERA click Search Device to search again Click one of the IP Camera listed on the left side The network configuration of this IP camera will show on the right side You may change the name of the IP Camera to your preference eg Office warehouse Change the parameter and click Submit then click OK It will apply the change and reboot the Device ester Rebooting wait Please make sure the subnet of PC IP address and IP CAM IP address are the same The same Subnet IP CAM IP address 192 168 1 200 PC IP address 192 168 1 100 Different Subnets IP CAM IP address 192 168 2 200 PC IP address 192 168 1 100 To Change PC IP address Control Panel Network Connections Local Area Connection Properties Inter
18. en two snapshots I O Setting Setting Input Setting Input 1 Sensor Input 1 Action LIFTP 1041 5 SD Samba Subject GPIO In Detected Interval 10 sec w Based on the schedule Output Setting Mode Setting onoff Switch Time Switch Interval a Input Setting IP Camera supports input and output When the input condition is triggered it can send the video to some specific mail addresses transmit the video to remote FTP server trigger the relay save video to local SD card or to SAMBA b Output Setting OnOff Switch means the camera executes the action when triggered Time Switch means the camera executes the action according to the interval you choose after triggered C Use the terminal block on the back of camera for I O connection Connect the external input devise to DI and G Ground and connect the external output devise to DO and G Ground 40 46 d The relay out can be switch on and off on the live video page 1970 JAN 08 14 37 20 Size 1280x 800 FPS 6 default Streaming 1 Chatting Online Visitor 1 iv Log List System Logs Logs Motion Detection Logs Logs Logs Logs All Logs Loqs oort by System Logs Motion Detection Logs and Logs In addition System Logs and I O Logs won t lose data due to power failure 41 46 CAMERA V gt Micro SD card Playback Please Insert
19. en you can use microphone which connects to the PC to talk to server side which is IP Camera side 6 Shows how many people connect to this IP camera 7 Select to enable or disable the relay Double click the video it will change to full screen mode Press Esc or double click the video again it will change back to normal mode Right Click the mouse on the video it will show a pop up menu snapshot Record start screen Zoom 1 Snapshot Save a JPEG picture 2 Record Start Record the video in the local PC It will ask you where to save the video stop recording right click the mouse again Select Record Stop The video format is AVI Use Microsoft Media Player to play the recorded file 3 Mute Turn of the audio Click again to turn on it 4 Full Screen Full screen mode 5 ZOOM Enable zoom in and zoom out functions Select Enable digital zoom option first within the pop up dialogue box and then drag and drop the bar to adjust the zoom factors Enable digital zoom Zoom Factors 113 96 15 46 CAMERA dp V Configuration Clic to get into the administration page Click to go back to the live video page Server Information MAC Address Server Hame EE E S Status Bar Language 9 English O French Russian O italian O Spanish O German O Portuguese Polish Japanese OSD Setting Time Stamp Enabled Disabled Text O Ena
20. lity Please carefully select the VBR rate to avoid picture breaking up or lagging 3 Video Frame Rate The video refreshing rate per second NTSC Max 30 frames second PAL Max 25 frames second 4 Size It means Group of Pictures The higher the GOP is the better the quality is 5 Video Format 264 MPEG4 or M JPEG 6 RTSP Path RTSP output connecting route 34 46 Streaming 2 Basic Streaming 2 Setting 3 4 5 Basic Mode Advanced Mode D Close Resolution 640x180 Quality Standard Video Frame Rate 30 FPS Video Format JPEG RTSP Path 5 Adress Audio G 711 Resolution There 5 resolutions be chosen 1920x1080 1280x720 640x480 320x240 176x144 Quality There are 5 levels to adjust Best High Standard Medium Low The higher the quality is the bigger the file size is Also not good for internet transmitting Video Frame Rate The video refreshing rate per second Video Format H 264 4 or M JPEG RTSP Path RTSP output connecting route d otreaming 2 Advanced Mode reaming 2 Setting OBasic Mode Advanced Mode Close Resolution 640x480 Quality Standard Video Frame Rate Video Format RTSP Path Adress Audin G 711 Resolution There 5 resolutions be chosen 1920x1080 1280x720 640x480 320x240 176x144 Quality There are 5 levels to adjust
21. ls Select Enable or Prompt ii IE gt Tools gt Internet Options gt Security Tab gt Custom Level gt Initialize and script ActiveX controls not marked safe gt Select Enable or Prompt 12 46 CAMERA IP CAMERA Microsoft Internet Explorer File Edit View Favorites and News E Back J x Pop up Blocker Manage Add ons Synchronize Windows Update Address hetp 192 168 1 2 Windows Messenger Internet Options Security Settings Settings Enable 19 Binary and script behaviors Administrator approved Disable Enable 19 Download signed Activex controls Disable Enable Prompt 1 Download unsigned Activex controls Disable 7 uud male A m me m mmn b er Te Reset custom settings Reset to Medium 5 Internet Options General Security Privacy Content Connections Programs Advanced a Web content zone to specify its security settings Internet Local intranet Trusted sites Restricted sites Internet 54 This zone contains all Web sites you haven t placed in other zones Security level for this zone Custom Custom settings To change the settings click Custom Level To use the recommended settings click Default Level Custom Level Default Level Security
22. net Protocol TCP IP Properties Please make sure your IP Camera and PC have the same Subnet If not olease change IP Camera subnet or PC IP subnet accordingly 4 Local Area Connection Properties 2 X Internet Protocol TCP IP Properties Ee Te General Authentication Advanced General Connect using You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for 88 Realtek RTL8139 Family PCI Fast Ethernet NIC the appropriate settings Obtain an address automaticall This connection uses the following items Use the following IP address El Client for Microsoft Networks IP address File and Printer Sharing for Microsoft Networks ivi QoS Packet Scheduler Subnet mask Internet Protocol TCP IP Default gateway Description Use the following DNS server addresses Transmission Control Protocol Internet Protocol The default Pr femed DNS server 192 Sra 4 o wide area network protocol that provides communication across diverse interconnected networks Alternate DNS server 158 35 wil 32 A C Show icon in notification area when connected A quick way to access remote monitoring is to left click the mouse twice on a selected IP Camera listed on Device list of IP Installer An IE browser will be opened 11 46 Static DHCP Name IP 192 168 1
23. nt certificate Client private key Status li PPPoE PPPoE Setting O Enabled Disabled Username E Password Send mail after dialed Enabled Subject From IPcam Select Enabled to use PPPoE 26 46 Username and password for the ADSL connection Send mail after dialed When connect to the internet it will send a mail to a specific mail account For the mail setting please refer to Mail and FTP settings iv DDNS It supports DDNS Dynamic DNS service a DynDNS DONS Setting Enabled Disabled Provider Hostname 1442 Username 4 Password Schedule Update 440 Minutes State 1 Schedule Update Feature of DDHS schedule update is designed for IP products which installed behind the IC5 or HAT devices Update range from every 5 minutes to 5000 minutes and 0 remain to off 2 Please note that the hostname will be blocked by DynDH org if schedule update is more than once every 5 minutes to 60 minutes In general schedule update in every 1440 minutes is recommended Enable this service Key in the DynDNS server name user name and password set up the IP Schedule update refreshing rate Click Apply If setting up IP schedule update too frequently the IP be blocked In general schedule update every day 1440 minutes is recommended n 27 46
24. ny characters Case sensitive 31 46 CAMERA C A V Setting i Image Setting Brightness Contrast Hue Saturation Sharpness AGC 16x Shutter Time Outdoor Sense Up 1 15 D WDR Off v Video Orientation Flip Mirror DNR 1 low For the security purpose there are three areas can be setup for privacy mask Click Area button first and pull an area on the above image Finally click Save button to reserve the setting Please refer to the details below for Image setting a Brightness Contrast Hue Saturation Sharpness can be adjusted here b AGC The sensitivity of camera can adjusts with the environmental light in order to avoid the images too light or too dark c Shutter Time You can use Outdoor or Indoor option or fix it from 32 46 CZFAlTYIEFAFA 1 30 10 1 1000 d Sense Up incerase the sensitivity of camera to get brighter image at night D WDR Enable the function to reduce the contrast of background with foreground ex people f Video Orientation Flip mirror or rotate the image as your requirement g DNR Adjust this option to reduce the noise ii Video Setting User may select the camera system type Streaming 1 Setting Basic mode and Advanced mode streaming 2 Setting Basic mode Advanced mode and 3GPP mode Max Video Frame Rate for both streaming combined is 30 FPS a Streaming 1 Basic Mode Streaming 1 Set
25. on Utility 45 46 Micro SD Card The following is the Micro SD Card recommended Transcend SDHC class4 SDHC class4 SD class4 SD 554 SDHC class6 SDHC class6 SDHC class6 SD 556 SD class6 SD 556 SDHC class4 SDHC class4 SDHC class4 46 46
26. ons Flash 16MB Lens Type 4 2mm F1 6 Sensitivity 1 0 Lux 25fps 4 46 eee Shutter Time 1 5 1 10 000 sec G 711 64K and G 726 32K 24K audio compression Audio Input Mic built in Output 3 5mm phone jack Support 2 way audio Operating Temperature Ethernet 10 100 Base T Network Protocol HTTP HTTPS SNMP QoS DSCP Access list IEEE 802 1X RTSP TCP IP UDP SMTP FTP PPPoE DHCP DDNS NTP UPnP 3GPP SAMBA Wireless Optional WEP WPA PSK WPA2 PSK 1920x1080 25fps 1280x720 25fps 640x480 30fps 320 240 0301 5 176x144 30fps Triple Streaming CMOS setting Brightness Contrast Hue Saturation Sharpness AGC Shutter Speed adjustment Sense Up D WDR Flip Mirror Noise reduction System Video Resolution Triggered action Mail FTP Save to SD card DO SAMBA 5 46 AMERA Pre Post alarm Yes configurable Security Password protection IP address filtering HTTPS encrypted data transmission 802 1X port based authentication for network protection QoS DSCP Firmware upgrade Simultaneous connection Up to 10 Micro SD card management Recording trigger Motion Detection IP check Network break down wire only schedule DI Video format AVI JPEG Video playback Yes Delete files Yes Web browsing requirement O Windows 7 2000 XP 2003 Microsoft IE 6 0 or above Hardware Suggested Intel Dual Core 2 53G RAM 1024MB Graphic card
27. s for video start and end time when motion detected I O or other devices got triggered Note Pre Post Alarm record time is base on record time setting and IP Cam built in Ram memory Limited by IP Cam built in Ram Memory When information is too much or video quality set too high it will cause recording frame drop or decrease on post alarm recording time d Network Dis connected When the network is down it will save the video to local SD card This function is only enabled under wire connection Network check Whenever the connection is down it records the video to SD card Make sure the video recording is continuous To use this function key in the IP address of the PC which has recording software installed Enable the function of Save to SD then click Apply The interval of two video files recorded on SD card is fixed with 30 seconds ii Schedule Schedule With schedule setup Snapshot Enabled Disabled Snapshot E mail FTP C Save to SD l Samba Interval 10 Second s 1 50000 File Hame Snapshot a schedule After complete the schedule setup the camera data will 39 46 recorded according to the schedule setup b Snapshot After enable the snapshot function user can select the storage position of snapshot file the interval time of snapshot and the reserved file name of snapshot Interval The interval betwe
28. secure identification identification at Http connection type 1 Created Request remove secure identification in Created request mode There is a warning message showing Please set Yes to remove secure identification 2 Setting the secure identification and apply it Create Request Country State or province Locality 3 Installed Certificate remove Certificate in Installed Certificate mode There will be a warning message to check again 4 There are two ways to set Certificate Install Signed Certificate and Create Self Signed Certificate 23 46 Install Signed Certificate Signed Certificate Create Self Signed Certificate Country State or province Locality Organization Organizational Unit Common Name Validity b SNMP Simple Network Management Protocol 1 Enable SNMPv1 SNMPv2 and write the name of Write Community and Read Community 2 Enable SNMPv3 please set Security Name Authentication Type Authentication Password Encryption Type Encryption Password of Write mode and Read mode 3 Enable SNMPv1 SNMPv2 Trap can detect the Trap server Please set what event need to detect SNHNMPv1 v2c Trap Trap Address Trap Community public Trap Event Cold Start Warm Start Link Up Authentication Failed SD Detect C Access list Enable IP address filter set IP address which can allow or deny to this camera There are two options single an
29. th PC s time Manual The date and time remain the same 17 46 Time Setting Server Time 2007 4711 14 56 01 Time Zone GMT 08 00 Date Format yyimm dd mmddyy ddimmAy Time zone GMT 408 00 HTP HTP Server GMT 06 00 Q Synchronize GMT 05 00 f GMT 04 00 GMT 03 30 Time GMT 03 00 GMT 02 00 Manual GMT 04 00 GMT 00 00 GMT 04 00 GMT 02 00 GMT 03 00 The date 03 30 li User Management IP CAMERA supports three different users administrator general user and anonymous user User Management Anonymous User Login Oves no Add User Username Password Confirm User List Userame User Group Modify admin Administrator a Anonymous User Login Yes Allow anonymous login No Need user name amp password to access this IP camera b Add user Type the user name and password then click Add Set e Click edit or delete to modify the user 18 46 a User Setting Microsoft Internet Username admin Password Confirm li System update System Update Firmware Upgrade Firrmruwarg Version M1 123 11 New Firmware Reboot System Start Fight click the mouse button on Setting Download and save a File then select Save 45 to save current system s setting in the New Setting Filo memi Poa Setting Management a To update the firmware online click Bro
30. ting O Basic Mode D Acvanced Mode Resolution 1920x1080 w Quality High v Video Frame Rate 30 FPS Video Format H 264 RTSP Path Adress Audin G 711 1 Resolution There are 5 resolutions can be chosen 1920x1080 1280x720 640x480 320x240 176x144 2 Quality There are 5 levels to adjust Best High Standard Medium Low The higher the quality is the bigger the file size is Also not good for internet transmitting 3 Video Frame Rate The video refreshing rate per second 4 Video Format H 264 MPEG4 or M JPEG 33 46 5 RTSP Path RTSP output name b otreaming 1 Advanced Mode Streaming 1 Setting Basic Mode Advanced Mode Resolution 1920 1080 Bitrate Control Mode CBR VBR Video Quantitative Video Bitrate JMbps Video Frame Rate 30 FPS GOP Size 1XFPS GOP 30 Video Format H 264 RTSP Path Adress Audio G 711 1 Resolution There 5 resolutions be chosen 1920x1080 1280x720 640x480 320x240 176x144 2 Bitrate Control Mode There CBR Constant Bit Rate and VBR Variable Bit Rate to use CBR 32Kbps 4Mbps the higher the CBR is the better the video quality is VBR 1 Low 10 High Compression rate the higher the compression rate the lower the picture quality is vise versa The balance between VBR and network bandwidth will affect picture qua
31. up port for HTTPS transmitting Default 443 20 46 d f CAMERA UPnP This IP camera supports UPnP If this service is enabled on your computer the camera will automatically be detected and a new icon will be added to My Network Places Note UPnP must be enabled on your computer Please follow the procedure to activate UPnP 1 open the Control Panel from the Start Menu 2 select Add Remove Programs 3 Select Add Remove Windows Components and open Networking Services section 4 Click Details and select UPnP to setup the service 5 The IP device icon will be added to MY Network Places 6 User may double click the IP device icon to access IE browser Rtsp Setting Rtsp Server Enabled Disabled RTSP Port 554 RTP Start Port 5000 1024 9997 RTP End port 9000 1027 10000 Multicast Setting Based on the Rtsp Server Streaming 1 IP Address 234 5 6 78 224 3 1 0 239 255 255 255 Port 6000 1 65535 TTL 15 1 255 Streaming 2 IP Address 234 5 6 79 224 3 1 0 239 255 255 255 Port 6001 1 65535 TTL 15 1 255 ONVIF 402 294 04 ODisabled Security Enabled Disabled RTSP Keepalive Enabled Disabled RTSP setting 1 RTSP Server enable or disable 2 RTSP Port setup port for RTSP transmitting Default 554 3 RTSP Start and End Port in RTSP mode you may use TCP and UDP for connecting TCP connection uses RTSP Port 554 UDP connection
32. wse to select the firmware Then click Upgrade to proceed Heboot system re start the IP camera Factory default delete all the settings in this IP camera Setting Management User may download the current setting to PC or upgrade from previous saved setting 1 Setting download Right click the mouse button on Setting Download gt Select Save AS to save current IP CAM setting in PC Select saving directory Save 2 Upgrade from previous setting Browse gt search previous setting gt open gt upgrade gt Setting update confirm gt click index html to return to main page 19 46 B Network IP Setting IP Camera supports DHCP and static IP IP Assignment DHCP Static IP Address Subnet Mask Gateway DHS 0 DHS 1 Port Assignment Web Page Port HTTPS Port UPnP Port Forwarding External Web Port External https Port External RTSP Port DHCP Using DHCP IP Camera will get all the network parameters automatically Static IP Please type in IP address subnet mask gateway and DNS manually Port Assignment user may need to assign different port to avoid IP Setting 192 168 1 202 255 255 255 0 192 168 1 254 168 95 1 1 168 95 192 1 Enabled Disabled Enabled Disabled conflict when setting up IP assignment 1 Web Page Port setup web page connecting port and video transmitting port Default 80 2 HTTPS Port set
Download Pdf Manuals
Related Search