USER MANUAL - Radioterminal
Contents
1. First digit for volume of transmission second digit for volume of reception You can set the value of volume between 1 and 5 Press ENETER to confirm and to return to upper level menu Press UP or DOWN to EXIT and press ENTER to return to standby status Setting of other paramters Press MENU in standby status LCD display shows MAINTENANCE in the first line Press UP or DOWN till LCD display show SET PARAMETER in the second line Press ENTER and LCD display shows SET PARAMETER in the first line and shows sub menu in the second line Press UP or DOWN to choose the submenu 1 MAX COMM TIME you can set the maximum communication time for each phone call Unit is minute You can set the time between 0 and 99 minutes When it is 0 it means no limit to the time Press DOWN to clear the current value and use the telephone set to enter the new value 2 GSM CODE LEN You can set the length of numbers dialled out from GSM line It is between 00 15 When the value is less than 3 the terminal only dials out the number if there is no new digit input after 6 seconds or is entered otherwise it will dial out the number 2 seonds later Press DOWN to clear the current setting Use telephone set to input new value 3 POLARITY REVERSE to enable or disable 4 GSM IF NO PSTN when PSTN is in fault if GSM IF NO PSTN ENABLED all calls should go via GSM if GSM IF NO PSTN disabled calls not go via GSM 5 PSTN IF NO GSM when GSM is i2. RADIO TERMINAL USER MANUAL Working mode 1 There are 3 modes for CG900T GSM PSTN or GSM PSTN GSM mode GSM will display on the right corn of the LCD display In this mode all calls can only be made via GSM line PSTN mode PSTN will show on the right corn of the LCD display In this mode all calls can only be made via PSTN line PSTN GSM mode PSTN GSM will show on the right corn of the LCD display In this mode calls can be made either from PSTN line or from GSM line 2 Please refer to User Setting for setting of working mode Please note when the main power supply is off all calls go via PSTN line Set up Take off the SIM card holder cover and insert the SIM card Connect the telephone set with the terminal via PHONE port using the grey colored special telephone cable Connect the PSTN line to the terminal via LINE port Power on the terminal If PIN checking is not activated on SIM card then within 45 seconds you can use the terminal If there is PIN checking in the SIM card LCD will show input pin code and you need to input the right PIN If LCD shows SIM PIN ERROR then you need to restart the terminal to input the right PIN after three times of trial you need to use PUK to unlock the SIM using mobile phone Outgoing calls Pick up the telephone handset or press hand free key dial your number after having the dial tone If you dial a barred gsm number LCD will show b
3. arred number please hookon The unit will choose the right path to send the number according to the preset routing rules Incoming calls In PSTN GSM mode you can have both PSTN and GSM incoming calls in GSM mode you can only have GSM incoming calls in PSTN mode you can only have PSTN incoming calls Incoming calls in PSTN GSM mode if there is incoming call from GSM line while the call is established on PSTN line the terminal will notify the user of GSM incoming call by dudu If the incoming call is still ringing after the user hangs up the user can still answer the incoming call If there is incoming calls from PSTN line while the call is established on GSM line the terminal will notify the user of incoming PSTN calls by dudu If the PSTN incoming call is still ringing after the user hangs up the user can still answer the incoming call Call Record In standby status press MENU and LCD display will show MAINTENANCE and the second line will show CALL RECORD Press ENTER and LCD display will show the first call record the first line will display call type call duration call date and time every 3 seconds the second line will display the number here are call types P I PSTN incoming call P O PSTN outgoing call G I GSM incoming call G O GSM outgoing call Press UP or DOWN to review other call records Set up of date and time Press MENU in standby status and LCD display wil
4. e first line and WORK MODE in the second line Press UP or DOWN till the LCD display shows SHORT CODE Press ENTER and LCD display shows SHORT CODE XX in the first line Here XX means the speed dial number In the second line LCD display shows the number For instance if the second line shows 17951056789 it means you can press XX to dial out the number 17951056789 Press UP or DOWN to veiw the complete list During process of viewing press ENTER to add speed dial number when LCD display shows ADD SHORT CODE in the first line Pick up the telephone handset input short code After the second line clears up go on to enter new code During process of adding press ENTER and LCD display shows DEL SHORT CODE in the first line Pick up the telephone handset press short code For instance to delete numbers beginning with 0574 from the speed dial list you can input 0574 Input to delete all Press ENTER to return to the process of reviewing press MENU to return to main menu Volume adjustment Press MENU in standby status LCD display shows MAINTENANCE in the first line Press UP or DOWN and LCD display shows GSM VOLUME in the second line Press ENTER and LCD display shows VOLUME MIC SPK in the first line and the current volume setting in the second line Press UP or DOWN to clear the second line Enter the new value for volume by telephone set
5. ent code convert rule the second line will clear up and you can enter new rule Press ENTER and LCD display will show DEL CONVERT CODE in the first line Pick up the telephone handest press code pick up the telephone handset press code and the second line will clear itself and you can delete a new code covert rule after that If you want to delete all code convert rules input Press ENTER to return to viewing process Press MENU to return to the main menu Set up barring numbers Barring numbers are only valid to numbers dialled out via GSM line Up to 30 items can be set and maximum digit for any prefix 12 Press MENU in standby status and LCD display shows MAINTENANCE in the first line and WORK MODE in the second line Press UP or DOWN till you come to BARRED CODE Press ENTER and LCD display shows BARRED CODE in the first line and the code in the second line For instance if it displays 179510 it means numbers beginning with 179510 will be barred for outgoing calls Press UP or DOWN to view the complete list of barred code Press ENTER to add new barred code when LCD display shows ADD BARRED CODE Pick up telephone handset input code For instance if you want to set 099 as barred code just input 099 You can input another barred code when the second line clears up Press ENTER and you can delete any preset barred code when LCD display shows DEL BARRED CODE Pick u
6. l show MAINTENANCE Press up or down till LCD display shows DATE amp TIME Press ENTER and LCD display shows date time when the number for day month year hour and minute glitters press UP or DOWN to change and press ENTER to confirm Setting of working mode Press MENU in standby status and LCD display shows MAINTENANCE Press up or down till LCD display shows WORK MODE Press ENTER the first line shows WORK MODE and the second line shows SINGLE GSM or DUAL PSTN GSM or SINGLE PSTN Press UP or DOWN to choose the mode and press ENTER to confirm If you choose PSTN or GSM you will return to MAINTENANCE if you choose PSTN GSM LCD display shows in the first line SET GSM DIALCODE and second line ENTER Y MENU N press MENU to return to MAINTENANCE Press ENTER to set routing rules table Routing tables are composed of prefixes for numbers dialled out via GSM line You can set up to 30 items of prefixes For each prefix no more than 10 digit is allowed LCD display shows GSM DIAL CODE in the first line and prefix in the second line For example 1860 that means all numbers beginning with 1860 will be dialled out via GSM line Press UP or DOWN to view the complete list of prefixes Press ENTER and you can add new prefixes when the LCD display shows ADD in the second line Precudres to add new prefix pick up te
7. lephone handset enter prefix and the second line will clear itself and you can enter new prefix after that Press ENTER and you can delete prefixes when LCD display shows DET in the second line Procures to delete prefix pick up the telephone handset press prefix and the second line will clear itself and you can delete a new prefix after that If you want to delete all prefixes input Press ENTER to return to the reviewing process press MENU to return to the main menu Set up of code convert rules Code convert rules only apply to numbers dialled out via GSM line You can set up to 30 items of convert rules Maximum digit for code 7 Press MENU in standby status LCD display shows MAINTENANCE in the first line and WORK MODE in the second line Press UP and DOWN till the second line shows CONVERT CODE Press ENTER and LCD display shows CONVERT CODE in the first line and the code in second line For instance 0 gt 179510 it means the digit 0 will be dialled out as 179510 when the number beginning with 0 is being routed via GSM line Press UP or DOWN to view the complete list of code convert rules Press ENETER and you can add new code convert rules when LCD display shows ADD CONVERT CODE in the second line Pick up telephone handset press original code code to be converted For instance if you want to convert 099 to 9 press 099 9 After you input the curr
8. mber for transferring the call Press DOWN to delete the number and press ENTER to confirm If PSTN to GSM call transfer is activated when there is incoming call from PSTN line and once the telephone set connected with the terminal rings the call will be dialled out via the GSM line to the preset number When the other party with the preset number answers the incoming call will be transferred from the PSTN line to the preset number on GSM line GSM TO PSTN Press MENU in standby status and LCD display shows MAINTNENACE in the first line and WORK MODE in the second line Press UP or DOWN till the LCD display shows CALL TRANSFER in the second line Press ENTER and LCD display shows PSTN TO GSM in the second line and press DOWN LCD display shows GSM TO PSTN in the second line Press ENTER and LCD display shows GSM CALL TRANSF in the first line and Disable or Enable_Assign or FEnable_Free in the second line Press UP or DOWN to chosse Enable_Assign Enable_Free or Disable If you choose Disable the terminal will not transfer any incoming call via GSM line If you choose Enable_Assign the terminal will transfer the incoming call from GSM line to preset number If you chhose Enable_Free the terminal will tranfer the incoming call from GSM line to any number entered by the calling party If you choose Disable or Enable_Free press ENTER to re
9. n fault if PSTN IF NO GSM enabled all calls go via PSTN if PSTN IF NO GSM disabled all calls will not go via PSTN 15 Technical Parameters 15 1 Power supply AC Input voltage 160V to 280V Power adaptor output DC7 5V 1 5A Backup battery 6V 4AH Lead Acid battery Optional Maximum charge current 600 mA DC input voltage range 7 5V to 10V DC Maximum DC current 700 mA DC7 5V exclude charge current 15 2 Working environment Working temperature 0to 45 C Relative humidity 10 to 95 Environment noise lt 60dB A Atmospheric pressure 86 to 106 KPa 15 3 GSM parameters Frequency bands GSM 850 900 18001900 MHz Automatic switch Frequency stability lt 2 5 ppm Receive sensitivity lt 100 dBm Transmit power lt 2W 850 900MHz lt 1W 1800 1900 MHz SIM card mode 3 3 V Antenna impedance 50 Ohm
10. p telephone handset input code For instance if you want to delete 0574 just input 0574 You can delete another code after the second line clears up Input to delete all codes Press ENTER to return to viewing process Press MENU to return to the main menu Set up call transfer PSTN to GSM when there are incoming calls from PSTN line the terminal can transfer the call from PSTN to GSM line and the call will be dialled out via preset number via GSM line GSM to PSTN when there are incoming calls from GSM line the terminal can transfer the call from GSM to PSTN and the call will be dialled out via PSTN line with the preset number or with the number input via the calling party PSTN to GSM Press MENU in standby status LCD display shows MAINTENANCE in the first line and WORK MODE in the second line Press UP or DOWN till LCD display shows CALL TRANSFER Press ENTER and LCD display shows PSTN TO GSM in the second line Press ENTER still and LCD display shows PSTN CALL TRANSF in the first line and shows Enable or Disable in the second line Press UP or DOWN to choose Enable or Disable If you choose Disable the terminal will not transfer the incoming calls via PSTN line to GSM line Choose Disable and press ENTER to return to main menu Chosse Enable press ENTER and LCD display shows PSTN TRANSF TO in the first line and in the second line shows the target nu
11. turn to main menu If you choose Enable_Assign press ENTER and LCD display shows GSM TRANSF TO in the first line and the target number in the second line Press DOWN to delete the number and ENTER to confirm Restrictions on call transfer This only applies to incoming call via GSM line If you set GSM TO PSTN call transfer you can set numbers that can be transferred Numbers that can be transferred apply only for incoming calls via GSM line You can set up to 30 pieces of numbers and maximum digit for each number is 12 Press MENU and LCD display shows MAINTENANCE in the first line and WORK MODE in the second line Press UP or DOWN till LCD display shows TRANS RESTRICT Press ENTER and LCD display shows PERMITTED CODE in the first line and in the second line the number will be displayed For instance 138 it means when the incoming call is from a number beginning with 138 the call will be transferred as preset Press UP or DOWN to view the whole list of PERMITTED CODE Press ENTER and add code when the LCD display shows ADD PERMIT CODE in the first line Pick up the telephone handset input the code prefix Press ENTER and delete the code when LCD display shows DEL PERMIT CODE After the code is deleted the LCD display will clear up and you can delete the next code Press to delete all codes Speed dial Press MENU in standby status LCD display will show MAINTENANCE in th
Download Pdf Manuals
Related Search