UPS + AVR User`s Manual
Contents
1. and minus pole through the from the outer enclosure accessible battery fuses when maintenance or service work inside the UPS is considered The lead acid battery may cause chemical hazard The battery presents a risk of electric shock and energy hazard Batteries will be disposed by the manufacturer or importer Customers need to send them back with no charge for disposal Electrical hazard the discharge time is about 5 min 12 B4 1KB SHIPPING DIM Lx Hx W 48 x 33 x 30 54 x 33 x 30 61 x 33 x 30 8 SPECIFICATIONS cm CAPACITY 1200VA 1700VA 2200VA WEIGHT NW G W 15 16 21 50 22 50 25 26 700W 1050W 1400W kgs INPUT Voltage Selectable 100 110 115 120V 19 or 200 220 230 240V 19 11 Frequency 50Hz 60Hz Auto detect 1 INTRODUCTION Current 110V 220V 12A 6A 16A 8A 21A 10A 1 1 Overview OUTPUT Voltage 100 110 115 120V 19 or 200 220 230 240V1 6 for Backup Mode The PowerStar series UPS is an advanced high performance stand by lt 10 forAVR et be cae Regal UE pore protai your F H Hz 0 1H D computer from utility line failure In the event of utility failure is a a LS blackout the UPS will rapidly transfer loads to an alternative power Wave Form Simulated Pseudo Sine Wave source which derives power from battery set inside the UPS Current 110V 220V 11A 5 5A 15 5A 7 8A 20A 9 8A The UPS provides two charging mode quick charging and trickle charging to maintain the batteries in the best condition Battery TRANSFER2. computer equipment will be protected during a utility failure it is important to make sure that the maximum power need of the equipment is not over the rated capacity of the UPS When blackout happens LED of operation status will become red and alarm will beep if the load is over the rated value Meantime if the overload is severe the UPS will shut down immediately for protecting UPS itself B4 1KB 5 7 TROUBLE SHOOTING Possible Cause Action to Take UPS no reaction while AC is connected Power output is normal UPS emits continuous beep and status LED shows RED UPS does not provide expected run time Button on front panel doesn t work Under AC mode UPS emits urgent beep 8 beeps per sec and replaces battery LED comes on No output when blackout happen 1 Line cord plug is loose 2 Fuse on rear panel blown Inside the drawer of inlet 3 Dead wall socket UPS is over loaded 1 Excessive loads connected at UPS s outlets 2 Battery is weak and cannot provide enough capacity 1 The CPU inside UPS is not running correctly 2 Button damaged Battery is weak and should be replaced 1 Dead battery 2 UPS NG 10 1 Check the line cord plug 2 Replace fuse 3 Check wall socket with a table lamp Tum off UPS and unplug excessive loads from UPS Do not operate the UPS and leave the UPS plugged in for 10 hours Then test it again if UPS still cannot provide expected run time
3. peripheral devices such as monitors modems external H Disk drivers etc To ensure the performance of the UPS Do Not load the UPS with laser printer motor or any type of inductive load Connecting the UPS to a two pole three wire grounding mains receptacle Connection with any other type of receptacle may result in a shock hazard and may violate local electrical codes Do not allow water or any foreign object to get inside the UPS And do not put objects containing liquid on or near the unit Keep UPS away from fire or heating sources The UPS is shipped from the factory with fully charged internal batteries however the batteries may lose some energy during delivery and storage To ensure that the UPS will provide the expected run time during a blackout the UPS must be left in charging for at least 5 hours before your first use The batteries would be recharged automatically by the UPS when the UPS is connected with city power INSTALLATION OPERAT ION amp AUDIBLE ALARM Installation Inspecting the packing carton for damage that may have occurred while in transit Immediately notify the carrier and place of purchase if any damage is found Retain the package for future use Plugging the poral cord to a 3 wire grounding receptacle If an extension cord must be used between the UPS and the nearest wall outlet use a 3 wire grounding type rated for at least 20 Amps Connecting your equipment to the UPS To ensure that your
4. To turn off the UPS please push the button for 3 seconds Audible alarm During a utility failure or fault operation the UPS emits beep for warning In back up mode the beeping can be silenced by pushing the button However the warning of low battery will still sound for urging user to leave computer without any data loss 6 B4 1KB 5 1 5 2 5 3 INDICATION AND CONTROL Battery level LEDs The battery level LEDs show the voltage level both in back up mode and in normal mode When the LED indicates 20 of the capacity in back up mode it means that the UPS is going to shut down for the length of backup time left it will depend on the load While when all five LEDs light in normal mode it means that the battery is fully charged Special status LEDs The Replace Battery LED would be on when the UPS s battery is no longer useful and must be replaced When the Alarm Off LEDs comes on the UPS will not emit beep during back up mode or when battery needs to be replaced However the low battery alarm and over load alarm will still sound for urging user to leave computer without any data loss The Charging LED would be on when the charger is charging the battery While the battery voltage is low in normal mode the charger will Keep on quick charging when the battery voltage is high the eager is keeping on for 4 seconds by every 24 seconds for trickle charging The Boost LED would be on when the UPS is connecting a low u
5. battery should be replaced 1 Push the button for 6 seconds to reset the UPS 2 Unplug line cord and all loads fromthe UPS and call for service Replace batteries 1 Replace battery 2 Call for service B4 1KB 6 COMMUNICATION INTERFACE Computer RS232 Pin2 AC Power Failure Pin4 Common GND of Pin2 amp Pin5 Pin5 UPS Battery Low Pin6 Turn off UPS Pin7 GND of Pin6 The interface with computer is diagramed as above for your reference Use Pin4 as the common of Pin2 and Pin5 Pin2 and Pin4 will become close loop from open when the utility fails Pin5 and Pin4 will become close loop from open when the battery level is low The UPS will shut down itself when the high level from RS 232 sustained for 3 seconds is applied between Pin6 and Pin7 B4 1KB 9 4 2 4 2 1 4 2 2 4 2 3 4 3 Operation When the power cord is connected with normal city power UPS will turn on automatically and go through the procedure of self test about 3 4 sec If test results are O K the green LED will be on Pushing the button for 3 seconds the UPS will turn off the power But the red LED will remain blinking when the AC power cord is connected To turn off the power completely please pull out the power cord For turning on the UPS again please connect back power cord and push the button During blackout push the button for 3 seconds until the buzzer emit beeping the UPS will turn on and enter into back up mode
6. B4 1KB UPS AVR Uninterruptible Power System User s Manual PowerStar Series 1200 1 700 2200 Replace Battery 100 Alarm Off O 80 Charging O 60 Buck O 40 Boost O 20 SPECIAL STATU BATTERY LEVEL O NORMAL BACKUP LOW BATT OVER LOAD B4 1KB ape 1 TABLE OF CONTENTS MEMO FRONT PANEL Page 2 REAR PANEL Page 3 1 INTRODUCTION Page 4 1 1 Overview 1 2 Battery replacement warning 1 3 Smart AVR 2 MAIN FEATURES Page 4 3 CAUTION Page 5 4 INSTALLATION AND OPERATION Page 5 6 4 1 Installation 4 2 Operation 4 3 Audible alarm 5 INDICATION AND CONTROL Page 7 8 5 1 Battery level LEDs 5 2 Special status LEDs 5 3 Auto self test function 5 4 Status LED and Alarm indication 5 5 Reset the UPS 6 COMMUNICATION INTERFACE Page 9 7 TROUBLE SHOOTING Page 10 8 SPECIFICATIONS Page 11 9 IMPORTANT SAFETY INSTRUCTIONS Page 12 B4 1KB B4 1KB B4 1KB MEMO Front Panel Replace Battery O Alarm Off O ets me O Charging O 60 Buck O 40 Boost O 20 SPECIAL STATU BATTERY LEVEL of 3 NORMAL BACK UP LOW BATT OVER LOAD LEDs of battery voltage level LEDs of UPS special status LED of oper
7. TIME 4 ms typical status indication including capacity low battery condition charging BATTERY Load Acid maintenance free condition and replace battery condition are shown on the front panel Voltage Capacity Le Paley ent warning Level Ind YES YES The self test function real time detection will inform you with an alarm when the batteries are weak and require replacement LED ALARM INDICATION 1 3 Smart AVR The UPS automatically corrects output voltage within the normal range Normalin charge GR ae Beep both in low utility voltage Boost LED lights up and high utility voltage Back up Abnormal Input Voltage Buck LED lights up conditions Abnormal Input Frequency Backup Green mode auto off Recharge Time 90 within 4 hrs 2 MAIN FEATURES Low Battery Battery Replacement Microprocessor based design Over Load Fault RED LED Flashing Continuous Beep Advanced indication for special operation status Replace Battery Alarm Off Charging Buck Boost Green mode function Auto select input frequency 50Hz 60Hz Self test function ENVIRONMENT TEMP dd dei 30 95 Non Condensing attery Hp acement indica or DIMENSIONS L x H x W 38x20x18 44x20x18 51x20x18 Extra wide range AVR function cm Standard RS 232 port for monitoring function Double protections for over load amp short circuit B4 1KB B4 1KB 4 1 CAUTION The UPS is designed to power computer loads and the associated
8. ation status VOO O Control button B4 1KB Rear Panel IEC Type Fuse Inlet of city power RS 232 port DB 9 O OO Outlet s NEMA IEC B4 1KB 3 IMPORTANT SAFETY INSTRUCTIONS When replacing the batteries use the same number and the same type of batteries Do not dispose of batteries in a fire the battery may explode Do not open or mutilate the battery or batteries released electrolyte is harmful to the skin and eyes A battery can present a risk of electric shock and high short circuit current The following precaution should be observed when working on batteries Remove watches rings or other metal objects Use tools with insulated handles To prevent an overbalance of this unit with the installation the additional stabilizer are to mount at the bottom side This unit should be installed from service personnel The equipment can be operated by any individuals without any previous experience The socket outlet shall be installed near the equipment and easily accessible With the installation of this equipment it should be prevented that the sum of the leakage current of the UPS an the connected consumer does not exceed 3 5mA Attention hazardous through electric shock Also with disconnection of this unit from the main hazardous voltage still may be accessible through supply from battery The battery supply should be therefore disconnected in the plus
9. set 8 B4 1KB
10. tility voltage The loads receive normal power The Buck LED would be on when the UPS is connecting a high utility voltage The loads receive normal power Auto self test function In normal mode of UPS turn on your computer and push the button on the front panel for self test The UPS will simulate a power outage and transfer your load to the UPS s battery If low battery warning sounds during the test it means that the battery set is weak and requires extended recharge If replace battery warning sound it means that the battery set is damaged and requires replacement B4 1KB 7 5 5 Status LED and Alarm Indication GRN LED no alarm City power normal ORG LED flashing two beeps 8 sec Backup mode ORG LED flashing one beep 4 sec No load Auto shut down after 24 sec ORG LED flashing quick beeping 4 beeps sec Low battery Red LED flashing continuous beeping Over load Replace battery LED urgent beeping 8 beeps sec Battery Replacement Reset the UPS If any abnormal condition occurs and the item 4 2 1 4 2 3 can not be executed please push the button for at least 6 sec until the buzzer emit continues beeping then the UPS is reset Under back up mode the UPS will be turned off by reset While under AC mode the UPS will go through the procedure of self test by re
Download Pdf Manuals
Related Search