Home

fertiliser distributor functions

1. DOSE RATE The required application rate is encoded here Encode the required application rate in TONS or cubic metres per hectare If TON HA is selected then the specific gravity of the slurry must also be encoded Moving the cursor to SPECIFIC GRAVITY and then encoding the value using the numerical keypad does this The maximum application rate that can be encoded is 99 9 Pressing the key changes between STEP Encode the size of the steps for the STEP function This value is the same for both and The maximum step size is 99 TANK VOLUME Encode the effective tank size here Used in connection with FULL TANK in operation Check by weighing some loads to get the effective TANK VOLUME Teglet 7 21 SLURRY SPREADER OTHER TYPE HYDR TEEJET 5000 OPERATORS MANUAL FILLED VOLUME Encode the amount filled if the tank is only filled e g half way up Must be encoded when the amount filled differs from the TANK VOLUME Pressing FULL TANK automatically transfers the amount encoded under TANK VOLUME Remember to encode the amount fil
2. OA 0 gt m m TEEJET 5000 OPERATORS MANUAL Select fertiliser distributor from the main menu as follows 1 Move the cursor using the arrow keys to FERTIL DISTRIB Press the SELECT key 2 Main menu select fertiliser distributor 3 ACCEPT or SELECT TYPE 4 Select type 5 It is now possible to choose between the displayed types 6 Select fertiliser distributor type 7 Accept type It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 4 14 Teefet 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR OTHER TYPE WITH REG FERTILISER DISTRIBUTOR OPERATION FORWARD SPEED The primary function under fertiliser distributor is forward speed Forward speed is
3. The effective working width of the spreader must be encoded under DISTRIB WIDTH before DOSE RATE is selected leefet 4 53 FERTILISER DISTRIBUTOR BREDAL HYDR B TEEJET 5000 OPERATORS MANUAL The required application rate and spreader setup is encoded thus 1 Encode the required application rate with the numerical keypad under DOSE KG HA 2 The SPECIFIC GRAVITY is found using the specific gravity tester supplied by BREDAL 3 Pressing CALC CALIB Calculates the correct SCALE and GEAR This menu cannot be left until CALC CALIB has been pressed The required DOSE RATE along with the specific gravity and the distributor width gives The scale setting The correct gear on the spreader NOTE The settings must be re calculated under DOSE RATE each time the working width of the spreader has been altered KG LEFT The amount filled into the spreader must be encoded here to be able to see how much fertiliser is left in the hopper NOTE If there is some fertiliser left in the hopper before refilling then this amount must be added to the amount filled thus Amount left in hopper filled amount Kg left HA LEFT Encode the size of the field to be spread
4. 4 IND gt S M S M S M The required seed rate in kilo per hectare with 1 decimal is encoded here Before the system can be calibrated it is necessary to encode the total working width of the seed drill If the encoded sow width is 0 the program will automatically change to sow width encodement remember that the effective sow width is encoded in centimetres pressing return changes the screen back to the calibration screen LOAD FIGURE Pressing this key changes to a different screen where it is possible to encode GRAMS PULSE should this be deleted by mistake 5 52 5000 OPERATORS MANUAL SEED DRILL LEMKEN CALIBRATION Calibration is essential for correct operation of the system The accuracy of all seed rates depends on this calibration Pressing the CALIB Key displays the screen to the left WARNING The drill shaft rotates when PRE CALIB is pressed Before pressing PRE CALIB Ensure that the seed drill is full and that the equipment used for calibration is fitted The drill shaft will rotate for 10 secon
5. FERTILISER DISTRIBUTOR BREDAL HYDR K Select fertiliser distributor from the main menu as follows 1 Move the cursor using the arrow keys to FERTIL DISTRIB Press the SELECT key 2 Main menu select fertiliser distributor 3 ACCEPT or SELECT TYPE 4 Select type 5 It is now possible to choose between the displayed types 6 Select fertiliser distributor type 7 Accept type It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 4 63 FERTILISER DISTRIBUTOR BREDAL HYDR TEEJET 5000 OPERATORS MANUAL LIME SPREADER OPERATION FORWARD SPEED KG MIN The primary function under fertiliser distributor is forward speed Forward speed is displayed in KPH with 1 decimal Forward speed is calculated from the signal from the speed sensor selected in encode wheel tractor wheel sprayer or radar KG MIN is displayed
6. leefet 5 63 SEED DRILL SIMBA TEEJET 5000 OPERATORS MANUAL FAN Revolutions per minute for the fan if 2 FANS OFF is selected See page 5 70 FAN 1 FAN 2 Revolutions per minute for both fans if 2 FANS ON is selected See page 5 70 1 2 WIDTH 1 1 WIDTH reduces the drill width by one half of the encoded When 1 2 WIDTH is selected the function of the key changes to 1 1 WIDTH and the drill width is returned to the encoded working width by pressing this key Pressing the NEXT PAGE key displays the first available functions HOLD KEY Press this key if the present bout is not required in the selected rhythm This function holds the present status regardless of how many times the drill is raised When this function is activated HOLD flashes on the display TRAMLINE INDICATOR No tramlines are made Tramlines are made FORWARD SPEED The forward speed is displayed in kilometres per hour with 1 decimal The forward speed is calculated from signals received from the sensor selected under ENCODE wheel tractor or radar 5 64 leefet 5000 OPERATORS MANUAL SEED DRILL SIMBA TRAMLINE CONTROL The primary function for seed drills is the track number The following picture is displayed B RACK NO Bout number Track number The bout number is the present bout b
7. 5 22 leefet 5000 OPERATORS MANUAL SEED DRILL NORSTEN Example of Method A Even a SJ N A rhythm of 4 is encoded in this example A single clutch or 1x2 solenoid shutters is fitted on the left hand side of the seed drill Tramlines are made LJ bout numbers 2 and 3 split when rhythm of 4 is encoded a Note where in the first 4 bouts around the whole field the bouts should be counted A and where bouts should not be counted all other corners After each trip around the field the machine is turned around and is driven in the opposite direction LRN Bout counting can be n controlled by using either the HOLD key or by using the TRACK keys 5 23 SEED DRILL NORDSTEN TEEJET 5000 OPERATORS MANUAL SEED DRILL ENCODEMENT This menu allows the operator to encode the various settings that are necessary for sowing Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements
8. 4 5 E I 5 A S W 0 gt 1 Press and hold the HOLD key min 5 seconds when the above screen is displayed see page 5 32 2 Move the cursor to 2 and it is now possible to select whether the drill is equipped with 1 or 2 fans 5 70 5000 OPERATORS MANUAL SEED DRILL SIMBA KG LEFT To see how much seed is left in the hopper the amount filled into the seed drill must be encoded here NOTE If there is some seed left in the hopper before refilling then this amount must be added to the amount filled thus Amount left in hopper filled amount Kg left HA LEFT Encode the size of the field to be sown before work commences This encodement is also used to calculate end time TRACK NUMBER Encode the tramline rhythm here Example The working width of the seed drill is 3 m The working width of the fertiliser spreader sprayer is 15 m Track number 15 3 5 The tramlining method to be used is also selected here A amp B The methods are described in the seed drill operation section SOW FIGURE The seed drill must be ready for calibration before pressing this key remember to turn the drill shaft a few times to fill the feed rollers
9. a I M The following is displayed It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 8 2 5000 OPERATORS MANUAL OTHER IMPLEMENT OTHER IMPLEMENT OPERATION DIESEL FUNCTIONS FORWARD SPEED The primary function for other implement is forward speed Forward speed is displayed in KPH with 1 decimal Forward speed is calculated from the signal from the speed sensor selected in encode wheel tractor wheel sprayer or radar AREA MEASUREMENT The worked area is displayed in Ha Area is displayed with 2 decimals from 0 to 99 99 ha And thereafter with 1 decimal from 100 to 999 0 ha NOTE a total counter for area can also be found in DATA DELETE VES DIESEL Fuel consumption in litres Fuel consumption in litres per hectare Fuel consumption in litres per hour DIESEL Diesel consumption since the last reset This function wo
10. 4 15 i43 6 ES EI LIC 4 16 2 4 17 Remi gp dm ee eer LEE 4 17 KO 4 17 Mazim 4 17 GALIBRA TION m P 4 18 DISTRIBUTOR WIDI F hese 4 19 5 m C E 4 19 DRIVE 4 19 UNIFORM PRESSURE scu id IL IUE 4 19 PULS RE ca rom Eee 4 19 FORWARD SPEED ES EFE PERO ERE ERE IKE 4 20 WHEEL L TIR uc P 4 20 WHEEL SPREADER 25 Satna Sense sess 4 20 RADAR 4 20 IMPLEMENT 4 20 WORK HOUR ON OFF M S 4 20 METRE SWITCH tec 4 20 NA EEE er EENE 4 21 WARNING 4 21 DATE C 4 21 4 13 FERTILISER DISTRIBUTOR OTHER WITH FERTILISER DISTRIBUTOR
11. TEST INPUT OTHER TYPE OTHER TYPE W REG TRAIL 1 Signal from shaft speed sensor Signal from RPM sensor fitted to RPM 1 discs RPM 1 TRAIL 2 Signal from shaft speed sensor Signal from floor chain RPM 2 RPM 2 or signal from weigh interface TRAIL 4 Signal from speed sensor fitted Signal from speed sensor fitted to trailed machines to the spreader TRAIL 7 Signal from area override sensor Area override ON OFF from the fitted to the spreader i e spreader open close TRAIL 8 Not used Not used TRAIL 15 Not used Not used TRAIL 16 Not used Not used BOM 1 12 Signal from boom section Signal from individual boom switches via system B plug sections via system B boom boom compensation if used section compensation if used TEST OUTPUT OUT 1 Not used Signal to the regulating device OUT 2 Not used Signal to the regulating device OUT 3 Not used Not used OUT 4 Not used Not used POT1 2 Not used Not used TESTINPUT B OGBALLE E EX amp D DZ BREDAL TRAIL 1 Signal from shaft speed sensor Signal from RPM 1 sensor TRAIL 2 Not used Signal from weigh cells TRAIL 4 Speed signal from trailed Signal from speed sensor fitted implement to the driving wheel TRAIL 7 Not used Area override sensor fitted to the arm of the driving wheel TRAIL 8 Not used Not used TRAIL 15 Not used Not used TRAIL 16 Not used Not used
12. 4 49 FERTILISER DISTRIBUTOR BREDAL HYDR B TEEJET 5000 OPERATORS MANUAL FERTILISER SPREADER OPERATION FORWARD SPEED KG MIN The primary function under fertiliser distributor is forward speed Forward speed is displayed in KPH with 1 decimal Forward speed is calculated from the signal from the speed sensor selected in encode wheel tractor wheel sprayer or radar KG MIN is displayed if MAN has been selected under in encode AREA MEASUREMENT The worked area is displayed in Ha Area is displayed with 2 decimals from 0 to 99 99 ha And thereafter with 1 decimal from 100 to 999 0 ha NOTE a total counter for area can also be found in DATA DELETE FERTILISER SPREADER FUNCTIONS KG HA RPM 1 Application rate in KG HA The shaft speed from sensor fitted to the spreader if MAN has been selected under encode KG Fertiliser consumption in kg KG LEFT Kg remaining in the hopper the amount must be encoded before starting Step dosage increase XX Step dosage decrease DOSE RATE NORMAL Encoding the required application rate or return to normal after using the step key 4 50 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL HYDR B XX
13. DOSE RATE QI AV 4 OW AC Or 4m O 2 gt omm 11 The required seed rate in kilo per hectare with 1 decimal is encoded here Before the system can be calibrated it is necessary to encode the total working width of the seed drill If the encoded sow width is 0 the program will automatically change to sow width encodement remember that the effective sow width is encoded in centimetres pressing return changes the screen back to the calibration screen LOAD FIGURE Pressing this key changes to a different screen where it is possible to encode GRAMS PULSE should this be deleted by mistake 5 24 leefet 5000 OPERATORS MANUAL SEED DRILL NORSTEN CALIBRATION Calibration is essential for correct operation of the system The accuracy of all seed rates depends on this calibration Pressing the CALIB Key displays the screen to the left WARNING The drill shaft rotates when CALIB Is pressed Before pressing CALIB Ensure that the seed drill is full and that the equipment used for calibration is fitted The drill shaft will rotate for 10 seconds when CALIB Has been pressed to ensure that the feed rollers a
14. 4 58 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL HYDR B WARNING ENCODE The following warnings can be set in this menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF MAX MIN limits for revolutions KM H Warning ON OFF MAX MIN limits for speed SLIP Warning ON OFF MAX MIN limits for wheel slip in RPM 1 Warning ON OFF MAX MIN limits for revolutions Encode as RPM KG LEFT Warning ON OFF and amount of kg min at which warning is wanted NB The encoded limits must exceed the limits encoded If a warning is required when an axle stops 0 RPM then set the minimum limit to 1 DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY FLOW FACTOR Please refer to the documentation supplied with the spreader for information regarding the FLOW FACTOR If the flow factor must be altered press and hold the HOLD key for approx 5 seconds before accepting the spreader type gt GEAR If the spreader is fitted with 7 gear then this must be encoded Press and hols the HOLD key for approx 5 seconds before accepting the spreader type 7 GEAR now be switched between ON if the spreader is fitted with a 7 gear and OFF if the spreader is not fitted with 72 gear 4 59 FERTILISER DISTRIBUTOR BREDAL HYDR B
15. 12 16 MONITORING 2 C 12 16 APPLICATION CON TROL os 12 18 Sed de ce ceeded tt 12 19 BALER i eh Ph Pol Ee 12 20 SEURRY SPREADER ae eu adeo 12 21 FITTING INSTRUCTIONS TEEJET 5000 OPERATORS MANUAL 5000 OPERATORS MANUAL FITTING INSTRUCTIONS FITTING INSTRUCTIONS TEEJET 5000 VER 4 The basic TeeJet 5000 computer fitting kit includes the computer mounting bracket cables junction box 2 sensors break away plug and various parts required for fitting This system can be expanded with various parts for the tractor i e PTO sensor for measuring PTO shaft speed diesel flowmeter for fuel consumption and radar for exact forward speed measurement ZA 0260 6026 2 system be expanded with kits for almost all implements depending upon requirements Fitting kits for the most common manufacturers and implement types are available as standard kits Fitting instructions for the various additions are delivered with the kits Teefet 12 3 FITTING INSTRUCTIONS TEEJET 5000 OPERATORS MANUAL GENERAL OVERVIEW nm 495 174 12 4 Teglet 5000 OPERATORS MANUAL FITTING INSTRUCTIONS SPARE PARTS TeeJet RESERVEDELE
16. 4 121 iP Eo 4 122 4 122 pido gi 4 122 eR 4 122 WORK HOUR ed 4 122 PTO SENSOR ere 4 123 WARNING ENCODE fp 4 123 DATE CLOCK estas eee ee 4 123 ERR 4 123 Teglet 4 113 FERTILISER DISTRIBUTOR RAUCH TEEJET 5000 OPERATORS MANUAL RAUCH AXERA H FERTILISER DISTRIBUTOR 02 ky gt me m E L Select fertiliser distributor from the main menu as follows 1 Move the cursor using the arrow keys to FERTIL DISTRIB Press the SELECT key 2 Main menu select fertiliser distributor 3 ACCEPT or SELECT
17. 4 32 eee 4 32 METRE SWITCH ee ee eee 4 32 WORK HOUR ON OFF 4 32 ic cci los asec vier esc 4 33 WARNING ENCODE 4 33 DATE t 4 33 Teglet 4 23 FERTILISER DISTRIBUTOR BOGBALLE TEEJET 5000 OPERATORS MANUAL INTRODUCTION The TeeJet 5000 BOGBALLE Fertiliser distributor program Maintain the correct application rate regardless of forward speed plus the ability to alter the application rate in steps depending on the crop s requirement The TeeJet 5000 controls the application rate using an actuator to control the gate position on the fertiliser spreader constant adjustment to maintain the application rate Visible and audible warnings given for incorrect rates forward speed PTO KG left etc NOTE The computer must be calibrated with the spreader to ensure correct operation This calibration must take place the first time the computer is connected to the spreader and each time the computer is connected to another spreader n S m 3 a 4 24 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BOGBALLE BOGBALLE FERTILISER DISTRIBUTOR Select fertiliser distributor from the
18. 2 It is now possible to select between the shown valve types 3 Select valve 4 Accept WARNING ENCODE The following warnings can be set in this menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warning ON OFF and MAX MIN limits for wheel slip in MIS DOSERATE Warning ON OFF and max difference in RPM 1 Warning ON OFF and MAX MIN limits for shaft speed Encode in RPM NB The encoded limits must exceed the limits encoded If a warning is required when an axle stops 0 RPM then set the minimum limit to 1 DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY 7 40 Teglet Slurry spreader Zunhammer SLURRY SPREADER 20 7 42 SLURRY SPREADER OPERATION ZUNHAMMER 7 43 SLURRY SPREADER FUNCTIONS WITH FLOW 7 43 SLURRY SPREADER WITHOUT FLOWNMIETER anre ntn nes 7 45 BOOM SECTIONS ON OFF te 7 45 SLURRY SPREADER ENGCOPBE
19. leefet 4 97 FERTILISER DISTRIBUTOR RAUCH AERO TEEJET 5000 OPERATORS MANUAL 3 Switch the main on off switch to on and the feed rollers will start turning The present feed roller RPM and the time in seconds will be displayed during the calibration procedure To ensure an accurate calibration the TeeJet 5000 must count minimum 500 pulses before the procedure can be stopped As soon as the computer has counted 500 pulses the screen will change and the calibration procedure can be stopped when required by switching the main on off switch to off NB Calibrating as much fertiliser as possible filling the bucket will ensure greater accuracy 4 Switch the main switch to off and the shown keys will be displayed If for some reason you do not wish to continue with the calibration procedure then press the CANCEL key 5 Weigh the amount released into the bucket exactly remembering to deduct the weight of the bucket Encode the amount released with 2 decimals using the numerical keypad displayed at the top of the screen 6 Press the CALC G PULSE key and the computer calculates the amount released per pulse and displays the amount at the top of the screen If you are satisfied with the result of the calibration pressing the ACCEPT key will allow you to save the calibration in 1 of 3 p
20. leefet 4 37 FERTILISER DISTRIBUTOR BREDAL TEEJET 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR OPERATION FORWARD SPEED The primary function under fertiliser distributor is forward speed Forward speed is displayed in KPH with 1 decimal Forward speed is calculated from the signal from the speed sensor selected in encode wheel tractor wheel sprayer or radar AREA MEASUREMENT The worked area is displayed in Ha Area is displayed with 2 decimals from 0 to 99 99 ha And thereafter with 1 decimal from 100 to 999 0 ha NOTE a total counter for area can also be found in DATA DELETE FERTILISER DISTRIBUTOR FUNCTIONS KG HA Application rate in KG HA KG Fertiliser consumption in Kg KG LEFT Total KG remaining in the hopper the amount must be encoded before start XX Step dosage increase XX Step dosage decrease DOSE RATE Encoding the required application rate or return to normal after using the step key 4 38 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL XX Percentile increase of the encoded application rate The size of the steps is altered in encode XX Percentile reduction of the encoded application rate The size of the steps is altered in encode NORMAL Only displayed if
21. 1 Using the arrow keys move the cursor over SLURRY SPREADER Press SELECT 2 Main menu select slurry spreader 3 Accept the selected type or choose another type 4 Select type 5 It is now possible to choose between the displayed types 6 Select the slurry spreader type 7 Accept It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 7 42 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER ZUNHAMMER SLURRY SPREADER OPERATION ZUNHAMMER Before the slurry spreader is used a PWM calibration of the proportional valve MUST be carried out This PWM calibration is normally carried out by the engineer when fitting the system to the slurry spreader The procedure for this calibration is described in the PWM section under ENCODE APPLICATION RATE The primary f
22. 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL FORWARD SPEED SENSOR A speed sensor is fitted to the spreader this sensor gives the correct number of pulses for controlling the application rate and this sensor should be selected If forward speed measurement is not required from the sensor mounted on the spreader WHEEL TRACTOR or RADAR can be selected Please refer to chapter 2 for forward speed sensor calibration IMPLEMENT SENSOR Using 1 of the following 3 options select how the area counter is to be switched on and off LIFT FERTILISER DISTRIBUTOR PTO The selected sensor is shown at the top of the display METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor SENSOR WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor 4 45 FERTILISER DISTRIBUTOR BREDAL TEEJET 5000 OPERATORS MANUAL REVS SENSOR PTO SENSOR If the TeeJet PTO sensor kit is used 932 983 encode T RPM 1 SENSOR The Bredal kit is supplied with a sensor fitted for disc speed the number of pulses per revolution should be set to 1 WARNING ENCODE The following warnings can be set in this menu It is recommended to turn all warnings which are not
23. PULSE WEIGHING Pulse weighing measure the amount spread by metering the speed of an axle that is related to the amount spread To ensure an accurate reading the system must be calibrated This calibration can be done automatically or manually 4 8 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR OTHER TYPE Automatic calibration This calibration takes place at the same time as the normal fertiliser spreader calibration The principle is that the computer counts the number of pulses from the pulse generator whilst calibrating When the spreader has been calibrated the amount weighed is encoded and the computer calculates the amount spread per pulse Method Prepare the fertiliser distributor for calibration 1 Select PULSE WEIGHING and then press CALIB CALC The picture to the left is displayed 2 NO OF PULSES must be at 0 before the calibration procedure commences If this is not the case then press the return key and then re enter the calibration screen Continue calibrating the spreader 3 Weigh the amount released move the cursor to WEIGHT using the arrow keys Encode the amount released in grams using the numerical keypad NOTE The pulse counter must have counted a number of pulses 4 Press the flashing CALC key and the calibration procedure is finished The CAL FIGURE is displayed at the top of the screen Note t
24. Percentile increase of the encoded application rate The size of the steps is altered in encode XX Percentile reduction of the encoded application rate The size of the steps is altered in encode NORMAL Only displayed if the step function has been used Normal application rate Regardless of how many steps the application rate has been increased decreased by pressing this key will return the application rate to normal DOSE RATE Pressing this key allows the application rate to be altered directly from the operation screen see also DOSE RATE in encode Pressing the NEXT PAGE key displays the next functions leefet 4 127 FERTILISER DISTRIBUTOR 5000 OPERATORS MANUAL Consumption tons since the last reset in DATA DELETE TON LEFT remaining in the hopper amount filled must be encoded before start RPM 1 Shaft speed of axle 1 TON Tons consumed measured via the pulse generator on the floor chain This function presupposes correct calibration of the system amount per pulse TON LEFT The amount remaining in the hopper Presupposes encoding the amount filled before start done in encode RPM 1 Shaft speed of axle no 1 Pressing the NEXT PAGE key displays the last available functions TON MIN Consumption flow in tons per minute Pressing the
25. 5 56 PTO SENSOR Jm D E 5 56 WARNINGS ieron 5 56 WARN DOSE 220299259222 900992 922 x 0 20 499 205 0 0 0 adi dU UNAM MM A dM 5 56 WARN WHEEL DBRIEE 5 57 DATE 6 qt 5 57 5 58 5 31 SEED DRILL LEMKEN LEMKEN SEED DRILL TEEJET 5000 OPERATORS MANUAL 1 Select drill from the main menu 2 Move the cursor using the arrow keys to DRILL when this is done press the SELECT key 3 Main menu Drill 4 ACCEPT the selected type or choose another type 5 Select type 6 It is now possible to choose between the displayed types 7 Select the drill type 8 ACCEPT It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other funct
26. 13 Tramlines are made when the present bout is the same as the j encoded rhythm track number Note where in the first 3 bouts around the whole field the bouts should be counted A and wu where bouts should not rg be counted all other corners Bout counting controlled by using either the HOLD key or by using the TRACK keys 2 3 EEEE WD ps 1116 9209 1302 5 8 5000 OPERATORS MANUAL SEED DRILL OTHER TYPE METHOD B EVEN The tramline cannot be split over 2 bouts inthis example with a rhythm of 4 encoded The first bout Q can only be sown with one half of the drill open Q ees Once this is done the NE tramlines can be made with clutches fitted to the middle of the drill Tramlines are made when the present bout number is the same the encoded rhythm track number Note where in the first 4 bouts around the whole field the bouts should H3 be counted A and where bouts should not er ee counted all other corners Bout counting can be controlled by using
27. 5000 OPERATORS MANUAL BALER OPERATION BALER FUNCTIONS BALER FORWARD SPEED The primary function under baler is forward speed Forward speed is displayed in KPH with 1 decimal Forward speed is calculated from the speed sensor selected in ENCODE wheel tractor or radar WEIGHT RPM 3 The secondary function is either weight or RPM selected under ENCODE Weight displayed in KG is possible if the baler is fitted with a weighing mechanism RPM 3 should be selected if the baler is not fitted with a weighing mechanism RPM is displayed instead of weight The TeeJet 5000 when used with a baler fitted with a weight system large bales weighs each bale individually The TeeJet 5000 cannot however record the weight of all the bales baled If no weighing system is connected to the TeeJet 5000 then RPM will be displayed instead of weight Select which is to be used under ENCODE Functions with weigh system RPM 1 Shaft speed of axle no 1 RPM 2 Shaft speed of axle no 2 UNITS Total bales bale counter TARRING Zero setting the weigh system Functions without weigh system Telet 6 3 BALER TEEJET 5000 OPERATORS MANUAL RPM 1 Shaft speed for axle no 1 choose when fitting the system A warning can be set on or off plus the number of pulses per rev are set under ENCODE RPM 2 Shaft speed
28. 7 33 te ee 7 33 TANK VOLUME 7 34 FILLED a 7 34 T 7 34 FLOW 218 ism E p Er 7 34 zie Burg 7 35 UNIFORM PRESSURE ees 7 35 FORWARD SPEED SENSOR 7 36 WHEEL TRACTOR AT UCET 7 36 RADAR M T 7 36 WHEEL SLURRY SPREADER raa riani 7 36 IMPLEMENT SENSU eee eee 7 36 spe C 7 36 WORK HOUR ON OFF t 7 36 REVS SENSOR fo 7 37 SYSIEM B PLUG 5r E ere ene Rp a 7 37 n 7 38 Me 7 38 lle cC EET 7 39 7 40 WARNING ENCODE cos 7 40 Bp Ries e quem 7 40 SLURRY SPREADER HORSCH TEEJET 5000 OPERATORS MANUAL SLURRY SPREADER HORSCH Select slurry spreader from the main menu as follows
29. TEEJET 5000 OPERATORS MANUAL The picture to the left is displayed once the field has been selected Drive to the field boundary start point and press START START Start field boundary measurement Drive around the field boundary Pressing the PAUSE key allows for a break in the field boundary measurement Pressing RE START resumes boundary measurement When the boundary is finished pressing BORDER DONE displays the following picture If there are any islands in the field i e lime pits trees etc These can be measured and added to the field survey ISLAND SURVEY Selects the island measurement function If there are islands in the field then pressing ISLAND SURVEY will display the island measurement screen DONE If there are no islands in the filed pressing DONE returns the screen to the main DGPS menu 9 6 5000 OPERATORS MANUAL DGPS If island survey has been selected the picture to the left will be displayed START Start island measurement DONE When there are no more islands ISLAND DONE When the island is measured PAUSE If a break in island measurement is required START Drive to the start of the island and press START drive around the island DONE If there are no more islands to be me
30. 7 47 Becic pc 7 47 ee ee eee 7 47 cO 7 48 FIEEED acess 7 48 HACE RI 7 48 7 48 BOOM WID TH pH 7 49 FER FERE EE FREE 7 49 FORWARD SPEED SENSOR 7 50 WHEEL TRACTOR RC 7 50 RADAR f 7 50 WHEEL SLURRY SPREADER eiue pente I onu 7 50 Eero IE EPEn 7 50 iss MC 7 50 WORK ease 7 50 REVS SENSOR M PM 7 51 FPILEMENU c 7 51 ilem UU 7 52 PROPOR IONAL esti el Cute 7 53 7 54 qo 7 54 Teglet 7 41 SLURRY SPREADER ZUNHAMMER TEEJET 5000 OPERATORS MANUAL SLURRY SPREADER ZUNHAMMER Select slurry spreader from the main menu as follows
31. 1 Using the arrow keys move the cursor over SLURRY SPREADER Press SELECT 2 Main menu select slurry spreader 3 Accept the selected type or choose another type 4 Select type 5 It is now possible to choose between the displayed types 6 Select the slurry spreader type 7 Accept It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 7 28 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER HORSCH SLURRY SPREADER OPERATION HORSCH Before the slurry spreader is used a PWM calibration of the proportional valve MUST be carried out This PWM calibration is normally carried out by the engineer when fitting the system to the slurry spreader The procedure for this calibration is described in the PWM section under ENCODE APPLICATION RATE The primary function for slurry spreaders is appli
32. EMPTY is pressed the tank size is transferred to TON M3 REST and the slurry spreader is ready to fill and spread again This function is also used in conjunction with flowmeter calibration see page number 7 8 TON M3 MIN The amount of slurry per minute going through the flowmeter Teejet 7 3 SLURRY SPREADER OTHER TEEJET 5000 OPERATORS MANUAL Pressing NEXT PAGE displays the next possible functions XX Step dosage increase Step dosage decrease NORMAL Return to the required normal application rate DOSE RATE Encoding the required application rate XX Percentile increase of the encoded application rate The size of the steps is altered in encode Percentile reduction of the encoded application rate The size of the steps is altered in encode NORMAL Only displayed if the step feature has been used Normal application rate Regardless of how many steps the application rate has been increased decreased by pressing this key will return the application rate to normal DOSE RATE Pressing this key allows the application rate to be altered directly from the operation screen see also DOSE RATE in encode Pressing the NEXT PAGE key displays the next functions RPM 1 Revolutions per minute RPM 1 The shaft speed of an axle is displayed here Normally the RPM of the distri
33. 4 106 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH BETA DELTA EMPTY HOPPER RPM AUTO MAN To ease emptying the hopper The gate can be opened completely by pressing this key only found in the BETA program Pressing this key displays the disc speed The minimum and maximum speed at which an alarm may be given for disc speed is set under ENCODE Pressing this key changes between automatic and manual application control During manual operation flashes at the bottom of the display Pressing the NEXT PAGE key displays the next functions Increased application rate Decreased application rate POS POS Actuator position gate opening Each key press increases the application rate If the key remains pressed then the application rate is increased by a suitable amount The actual application rate can be seen on the display Each key press decreases the application rate If the key remains pressed then the application rate is decreased by a suitable amount The actual application rate can be seen on the display Pressing this key displays the gate position changes between the left and right hand side 4 107 FERTILISER DISTRIBUTOR RAUCH BETA DELTA TEEJET 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR ENCODE This menu allows the operator to encode the various settings that are necessary for s
34. 5000 OPERATORS MANUAL DGPS GPS OFFSET Only displayed if the DataLink module being used has been delivered from TeeJet Technologies after 1 7 2000 Please contact your local dealer for further information The distance in metres between the DGPS antenna and the position at which the e g fertiliser is placed If the implement is behind the DGPS antenna then a GPS OFFSET should be encoded If the implement is in front of the DGPS antenna then a GPS OFFSET should be encoded WARNINGS The following warnings can be displayed This alarm is given when there is no communication between the TeeJet 5000 and the DataLink module The warning can be given by switching the DataLink module off or that the PCMCIA data card was NOT inserted before the DataLink module was started Pressing the OK key changes the screen to the main DGPS menu If there are still communication problems between the TeeJet 5000 and the DataLink module the warning will be given at regular intervals Teglet 9 9 DGPS TEEJET 5000 OPERATORS MANUAL This warning is given when no position signals are received Pressing the OK key returns the screen to the operation screen A warning is given again when a positional signal is received again FILE MANAGEMENT To avoid over filling the PCMCIA data card we recommend removing processed data on the card at regular inter
35. 4 84 lij cy 4 85 WEIGHING ON 4 85 DISTRIBUTOR We Tm 4 86 STER eem 4 86 FORWARD SPEED SENSOR tee 4 86 WHEEL TRACTOR AND 4 86 METRE 4 86 WORK HOUR ON OFF 4 87 SENSOR 4 87 VARIN GIN bl 4 87 DATES 4 87 a ee eee ee EE 4 87 4 75 FERTILISER DISTRIBUTOR BREDAL RAMP TEEJET 5000 OPERATORS MANUAL INTRODUCTION TeeJet 5000 used to control the BREDAL K lime spreader with auger Maintain the correct application rate regardless of forward speed plus the ability to alter the application rate in steps depending on the crop s requirement The TeeJet 5000 controls the application rate using a proportional valve that adjusts the amount of oil to a hydraulic pump which in turn alters the belt and auger speed Visible and audible warnings given for incorrect rates forward speed PTO KG left etc NOTE The computer must be calibrated with the spreader to ensure correct operation This calibration must take place the first time the computer is connected to the spreader and each
36. 56 deor oo io eoe 12 7 POWER SUPPLY ee ox MO 12 8 FITTING THE FORWARD SPEED SENSOR operentur Po 12 9 FITTING THE AREA OVERRIDE 12 11 FITTING THE BREAK AWAY PLUG ers cre roe eren een Fete een et exe epo Fes tex e ERE FE 12 12 CABLE 15 lC 12 12 CONNECTIONS IN THE JUNCTION 12 13 MULTI CABLE FROM THE TEEJET 5000 s 12 13 MULTI CABLE FROM THE BREAK AWAY 12 13 DIESEL FEOWMEFE a pc tenes Jo nn iind 12 13 12 13 POVIER SUPPLY epe Ep ED e ex Pepe 12 13 12 13 PTO SENSOR RPM I HH RR Ee Us 12 13 SPEED SENSOR e Li Em M RA ed 12 13 BREAK AWAY PLUG 12 14 SERAYER adipose t rud situ eic nonu spe su nuls Np uds 12 14
37. GENERAL FUNCTIONS TEEJET 5000 OPERATORS MANUAL TEST INPUT RAUCH AXERA H REIL TRAIL 1 Signal from shaft speed sensor Signal from RPM sensor fitted to RPM 1 discs RPM 1 TRAIL 2 Not used Signal from floor chain RPM 2 TRAIL 4 Speed signal from trailed Signal from speed sensor fitted implement to the spreader TRAIL 7 Area override on off signal from Area override ON OFF from the implement spreader TRAIL 8 Not used Not used TRAIL 15 Not used Not used TRAIL 16 Not used Not used BOM 1 12 Error is displayed as no boom Signal from individual boom interface is connected sections via system B boom section compensation if used TEST OUTPUT OUT 1 Signal to close the gate left Signal to the regulating device OUT 2 Signal to open the gate left Signal to the regulating device OUT 3 Signal to close the gate right Not used OUT 4 Signal to open the gate right Not used POT1 2 Shows the position of the Not used actuators 2 26 5000 OPERATORS MANUAL TEST INPUT OUTPUT SEED DRILL GENERAL FUNCTIONS TEST INPUT OTHER TYPE NORDSTEN TRAIL 1 Signal from RPM sensor fitted to Signal from RPM sensor fitted to the drill shaft the drill shaft TRAIL 2 Signal from RPM sensor fitted to Signal from RPM sensor fitted to the tramlining clutches When the drill
38. Lo Bow 5 O RPM SENSOR 3 268 OR _____ BROWN 5 WEIGHING MODULE BLACK 2 RPM SENSOR 2 6 BROWN 5 RPM SENSOR 1 BLUE 6 Using the standard kit for balers from TeeJet Technologies gives a better and neater installation which is prepared for additions 1 TeeJet 5000 baler monitoring kit Includes TeeJet no 910 180 junction box breakaway plug with cable 2 RPM sensors and a bale counter 2 RPM sensor kit TeeJet no 930 983 3 Bale weighing module to be ordered depending on baler make and model 12 20 Teejet 5000 OPERATORS MANUAL FITTING INSTRUCTIONS SLURRY SPREADER SLURRY SPREADER SENSOR WIRE COLOUR PIN NUMBER RPM SENSOR 1 FLOWMETER SIGNAL WHEEL SENSOR IMPLEMENT SENSOR The following shows an example of equipment for a slurry spreader Y 8 I 8 98218 0805 1 Junction box 6 RPM sensor 2 Connecting cable 7 Reg Valve 3 Pressure sensor 8 Actuator 4 Flowmeter 9 Motor control 5 Speed sensor Telet 12 21 5000 Monitor Malhavevej 2 9440 Aabybro Denmark Tel 45 9696 2500 Fax 45 9696 2501 Display Function keys Enter Tractor info Contrast Memory Hold Delete Display light
39. 4 123 FERTILISER DISTRIBUTOR RAUCH TEEJET 5000 OPERATORS MANUAL 4 124 Fertiliser distributor Reipl 4 126 FERTILISER DISTRIBUTOR OPERATION 2 4 127 FERTILISER DISTRIBUTOR 4 127 SEC er ee ee 4 128 4 129 DOSE eee 4 129 4 129 TON LEFD Mc 4 130 pee 4 130 CALIBRA TON oaa eee cece cece ee cee 4 130 AUTOMATIC CALIBRATION 4 130 MANUAL CALIBRA ION 4 131 DISTRIBU TOR WIDTH 4 131 STEP 4 131 DRIVE FAC TOR EKANA EPEE TSERE PAPIEREN AETERNE 4 131 REVS SENSOR ee 4 132 FORWARD SPEED SENSOR 4 132 WHEEL TRACTOR usc 4 132 WHEEL SPREADER uta tbt
40. METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor SENSOR WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor 5 12 5000 OPERATORS MANUAL SEED DRILL OTHER REVS SENSOR Encode the number of pulses the sensors fitted to the drill shaft give per revolution It is also possible to select between clutch monitoring and RPM monitoring monitoring fan speed on pneumatic machines PTO SENSOR Encode 1 if the TeeJet PTO sensor kit 932 983 is used DRILL SENSOR Encode 12 if the TeeJet pulse giver 905 152 or 906 152 is used Sensors that generate fewer than 4 pulses per revolution cannot be used CLUTCH SENSOR Encode 12 if the TeeJet pulse 905 152 or 906 152 is used Sensors that generate fewer than 4 pulses per revolution cannot be used If you require monitoring of e g a fan on a pneumatic seed drills select RPM at the bottom of the screen The above example shows clutch monitoring tramlining clutches and the number of pulses per revolution is 12 leefet 5 13 SEED DRILL OTHER TEEJET 5000 OPERATORS MANUAL WARNING ENCODE The following warnings can be set in
41. Please refer to chapter 2 for forward speed calibration IMPLEMENT SENSOR This sensor starts and stops the area counter A pressure sensor should be fitted on slurry spreaders between the pump and the distributor macerator so that the sensor generates a signal when the pressure drops If this is the case then SLURRY SPREADER should be selected If a sensor for PTO speed is fitted then this can be used as an area override sensor select PTO METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor IMPLEM SENSOR 7 10 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER OTHER SYSTEM B PLUG There are 2 system plugs on the back of the TeeJet 5000 The System A plug is compatible with o der TeeJet 5000 versions The System B plug is for new connections ACTIVE 0 VOLT The individual sections are opened with OV ACTIVE 12 VOLT The individual sections are opened with 12V WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor REVS SENSOR Encode the number of pulses per revolution given for the individual sensors Teglet 7 11 SLURRY SPREADER OTHER TEEJET 5000 OPERATORS MANUAL WARNING ENCODE The following warnings can be set in th
42. WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor METRE SWITCH Select whether the distance counter is started stopped manually via the function key in the operation menu or by the selected implement sensor SYSTEM B PLUG There are 2 system plugs on the back of the TeeJet 5000 The System A plug is compatible with o der TeeJet 5000 versions The System B plug is for new connections ACTIVE 0 VOLT _ The individual sections are opened with OV 12 VOLT The individual sections are opened with 12V ON OFF ON system plug is used OFF The system B plug is not used leefet 4 133 FERTILISER DISTRIBUTOR 5000 OPERATORS MANUAL WARNING ENCODE The following warnings can be set in this menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warning ON OFF and MAX MIN limits for wheel slip in MIS DOSERATE Warning ON OFF and MAX difference in TON LEFT Warning ON OFF and amount of ton min at which warning is wanted RPM 1 Warning ON OFF and MAX MIN limits for shaft speed Encode in RPM NB The encoded limits must exceed the limits encoded If a warning is required when an axle stops 0 RPM then set the minimum limit to 1
43. 5000 OPERATORS MANUAL SLURRY SPREADER HORSCH SLURRY SPREADER WITHOUT FLOWMETER TON M3 Slurry consumption in ton m3 uM 7 RPM 1 Revolutions per minute TON M3 The amount of slurry spread since starting This function works as a trip counter and be deleted in The total counter is also found here RPM 1 The shaft speed of an axle is displayed here Normally the RPM of the distributor macerator BOOM SECTIONS ON OFF The picture shows that the spreader has 2 sections and only one is open The total number of sections must be encoded in DISTRIB WIDTH When the override sensor is activated not measuring I area T is displayed Teejet 7 31 SLURRY SPREADER HORSCH TEEJET 5000 OPERATORS MANUAL DAILY USE OF THE SLURRY PROGRAM WITH A FLOWMETER Once all of the encodements have been accepted proceed as follows Start spreading and each time the area override sensor is activated implement sensor the following warning is displayed When this screen is displayed you have the following options If the machine is turning at the headland then continue driving and the warning screen will disappear when spreading starts again If you stop spreading temporarily without the tank being empty press PAUSE to remove the warning The warning screen will disappear when spreading starts again If the tank is empty press TANK
44. Speed Simulate key To use this function do as follows Set the Speed Simulate function to ON select the operation screen for the required implement and enter in a speed using the numeric keypad Speed simulation can be cancelled in 2 different ways 1 Drive the machine forward As soon as a pulse from the wheel sensor is given speed simulate will be cancelled 2 Encode the simulated speed as 0 after 8 seconds select System and switch Speed Simulate OFF GPS SYSTEM Select whether the DGPS functions are available or not only displayed if the TeeJet 5000 is a DGPS version SYSTEM DATA System settings not available to the user IMPLEMENT INFO The total time and area that the TeeJet 5000 has been in operation only registered if area is being counted COUNTER OVER shows the amount of time and the total area that the implement has been used over the max operating speed set by the implement manufacture Teefet 2 33 GENERAL FUNCTIONS TEEJET 5000 OPERATORS MANUAL GENERAL WARNINGS The TeeJet 5000 has the following general warnings Ol PTR WARN BATT Displayed when the power supply to the TeeJet 5000 falls to 10V This warning disappears when the power supply reaches 10V again WARN OUTPUT Displayed when there is a short circuit on a controlling device i e clutches
45. the 78 same the actual amount left in the ST sprayer then the sprayer flowmeter should be calibrated VOLUME Fill volume is calculated when this key is pressed START FILLING Pressing this key starts filling and the amount is metered through the filling flowmeter FLOW FIGURE This value is the calibration figure for the filling flowmeter Filling flowmeter Teglet 3 7 SPRAYER TEEJET 5000 OPERATORS MANUAL CALIBRATING THE FILLING FLOWMETER It is necessary to calibrate the filling flowmeter before it can be used accurately Using the program in the TeeJet 5000 for calibration makes this process easy The accuracy of this calibration depends on the amount that is used for calibration The following example uses 1000 It 1 Press the FLOW FIGURE key the under menu 2 Check that a flow figure has been encoded if not then encode e g 5000 as a start figure 3 Press the return key to go back to the previous screen 4 Encode an amount in FILL VOLUME that is approx twice as much as you expect to fill into the tank 5 Select START FILLING in the under menu 6 Fill the sprayer with an exact known amount through the filling flowmeter 1000 Lt In this example Fill the sprayer under normal working conditions same pressure time etc 7 Select FLOW FIGURE again move the cursor to TANK LIT and encode the exact known amount that was filled in to the s
46. 7 44 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER ZUNHAMMER SLURRY SPREADER WITHOUT FLOWMETER TON M3 Slurry consumption in ton m3 uM 7 RPM 1 Revolutions per minute TON M3 The amount of slurry spread since starting This function works as a trip counter and can be deleted in DATA DELETE The total counter is also found here RPM 1 The shaft speed of an axle is displayed here Normally the RPM of the distributor macerator BOOM SECTIONS ON OFF The picture shows that the spreader has 2 sections and only one is open The total number of sections must be encoded in DISTRIB WIDTH When the override sensor is activated not measuring I area I is displayed Telet 7 45 SLURRY SPREADER ZUNHAMMER TEEJET 5000 OPERATORS MANUAL DAILY USE OF THE SLURRY PROGRAM WITH A FLOWMETER Once all of the encodements have been accepted proceed as follows Start spreading and each time the area override sensor is activated implement sensor the following warning is displayed When this screen is displayed you have the following options If the machine is turning at the headland then continue driving and the warning screen will disappear when spreading starts again If you stop spreading temporarily without the tank being empty press PAUSE to remove the warning The warning screen will disappear when spreading starts again If the tank
47. DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY 4 134 Seed drill SEED DRILL OTHER TYPE minerong ipine 5 1 SEED DRILL NORDS TEN A EALE ne abe eee ehe Ee ehe Ene eene CEARA ROLERA PAAA LEen 5 15 SEED DRILL eee 5 31 SEED SIMBA ced tid chad deed thd bland ee dead deta 5 61 Seed drill Other type DRILL O aed add erc 5 2 SEED DRILL OPERATION OTHER 5 3 HOLD KEYS E S 5 3 TRAMLINE INDICATOR nc 5 3 TRAMLINE CONTROL ae eke uM I i eee 5 4 METHOD TN TT p DE 5 4 ME LHOD B aa m 5 5 FORWARD SPEED E tiat ati decides dte uultu 5 5 METHOD A UNEVEN e 5 6 NE Oy a AA A A ee 5 7 METHOD B UNEVEN e 5 8 METHOD BEVEN oara a T 5 9 SEED ENCODEMBNLT ie e pio epe time Rt a DR UM mio Edu URS neu 5 10 KOGLER emm 5 10 HA LEFT 5 10 Eje S iz qt nee ere rere rer 5 10 ee eee eee a eee ee ee ee 5 11 ROW sais 5 11 dcr EN
48. Encode the number of pulses per revolution given for the individual sensors SYSTEM B PLUG There are 2 system plugs on the back of the TeeJet 5000 The System A plug is compatible with o der TeeJet 5000 versions The System B plug is for new connections ACTIVE 0 VOLT The individual sections are opened with OV ACTIVE 12 VOLT The individual sections are opened with 12V Teejet 7 37 SLURRY SPREADER HORSCH TEEJET 5000 OPERATORS MANUAL FILL MENU Before the slurry spreader is used a PWM calibration of the proportional valve MUST be carried out This PWM calibration is normally carried out by the engineer when fitting the system to the slurry spreader The procedure for this calibration is described in the PWM section under ENCODE It is possible to use a fixed displacement pump for filling the slurry spreader When the fill signal and the implement signals are active the pump will run at a pre encoded speed 1 Set the spreader to fill 2 Press and keys to adjust the required pump speed 3 The pump speed will change and the actual RPM is displayed 4 When the required pump speed has been reached press the RETURN key REG BREAK This menu allows for selection between regulation stop ACTIVE or regulation stop INACTIVE by the implement sensor If INACTIVE is selected the slurry will run via t
49. Note where the bouts should be counted A and where bouts should not be counted all other corners in the first 4 bouts around the whole field Bout counting can be controlled by using either the HOLD key or by using the TRACK keys 5 45 SEED DRILL LEMKEN TEEJET 5000 OPERATORS MANUAL METHOD F This method is used when the seed drill is 12 metres wide and the implement used to cultivate the crop is 18 metres wide A fixed rhythm of 6 is used see page 5 55 Example of method F Right The seed drill is fitted with 2x2 magnetic valves on the right hand side of the drill and 2x2 magnetic valves fitted to the left hand side of the drill Drilling is started on the right hand side of the field as shown on the diagram One half of the drill must be closed for the first bout Thereafter the track number should be set to 6 6 and tramlines are made on the left side of the drill Tramlines are made when the present track number is 1 3 4 8 6 Note where tracks should be counted A and where tracks should not be counted all other corners in the first 3 bouts around the whole field Track counting can be controlled by using either the HOLD key or by using the TRACK keys TTA dh Hog ggg gr
50. Percentile increase of the encoded application rate The size of the steps is altered in encode XX Percentile reduction of the encoded application rate The size of the steps is altered in encode NORMAL Only displayed if the step feature has been used Normal application rate Regardless of how many steps the application rate has been increased decreased by pressing this key will return the application rate to normal DOSE RATE Pressing this key allows the application rate to be altered directly from the operation screen see also DOSE RATE in encode Pressing the NEXT PAGE key displays the next functions RPM 1 Weighing in KG using weigh cells fitted on the spreader only displayed if WEIGHING ON is selected under encode RPM BELT Tarring the weigh cells this key must be held down for approx 3 seconds only displayed if WEIGHING ON is selected under encode Pressing the NEXT PAGE key displays the next functions WEIGHT Weighing in KG using weigh cells fitted on the spreader only displayed if WEIGHING ON is selected under encode TARRING Tarring the weigh cells this key must be held down for approx 3 seconds only displayed if WEIGHING ON is selected under encode Using weighing if the system is fitted with weigh cells Calibrating the weigh cells is a condition for correct operation The calibration procedure is descr
51. Press the key and the following is displayed NB All counters used for calibration are zero set when this screen is displayed Never turn the drill shaft until you are completely ready to calibrate the drill NO OF PULSES must be 0 before starting calibration 1 Select the SOW FIGURE menu If any pulses have been counted press the RETURN key and select SOW FIGURE again 2 Turn drill shaft as described in the calibration table for the seed drill 3 When the manual calibration is finished weigh the amount released 4 Using the arrow down key move the cursor to WEIGHT and encode the weight of the released amount using the numerical keypad 5 Press the flashing CALC Key The computer divides the weight released by the number of pulses counted and the calibration procedure is finished The calculated value is displayed at the top of the screen note this figure if the computer is to be used with other seed drills using other calibration figures The value can be encoded directly using the numerical keypad 5 71 SEED DRILL SIMBA TEEJET 5000 OPERATORS MANUAL ROW NO Encode the total number of rows that the seed drill has ROWS IN TRACK Encode the number of rows that are shut when tramlines are being made This encodement is necessary for correct KG metering If the sown amount is not reduced when making tramlines encode 0 SOW WIDTH The seed
52. To ensure correct page layout etc We recommend using COURIER type with a size of 10 cpi Teglet 2 15 GENERAL FUNCTIONS DATA DELETE TEEJET 5000 OPERATORS MANUAL This menu comprises of 3 main options 1 Total counter display not found elsewhere Trip counter display 2 Delete counters separately 3 Delete all trip counters simultaneously It is not possible to see select the total counters in the operation menus Therefore the DATA DELETE function is the only one offering these readings Set the cursor using the arrow keys on the counter to be zeroed Pressing DELETE deletes this counter If DELETE TRIP is pressed all trip counters will be zeroed deleted simultaneously The functions are TIME TIME HA HA METRE DIESEL AMOUNT AMOUNT NOTE Trip counter for consumed time since last Zeroing Total counter for consumed time since last zeroing Trip counter for worked area since the last reset Total counter for area since last zeroing Travelled metres since the last reset Deleted as the total counter Fuel consumption since the last reset Deleted as the total counter Trip counter for consumption since the last reset Total counter for consumption since the last reset The TOTAL counters are onl
53. Track number 15 3 5 The tramlining method to be used is also selected here A amp B The methods are described in the seed drill operation section 5 10 leefet 5000 OPERATORS MANUAL SEED DRILL OTHER SOW FIGURE The seed drill must be ready for calibration before pressing this key remember to turn the drill shaft a few times to fill the feed rollers Press the key and the following is displayed NB All counters used for calibration are zero set when this screen is displayed Never turn the drill shaft until you are completely ready to calibrate the drill NO OF PULSES must be 0 before starting calibration 1 Select the SOW FIGURE menu If any pulses have been counted press the RETURN key and select SOW FIGURE again 2 Turn the drill shaft as described in the calibration table for the seed drill 3 When the manual calibration is finished weigh the amount released 4 Using the arrow down key move the cursor to WEIGHT and encode the weight of the released amount using the numerical keypad 5 Press the flashing CALC Key The computer divides the weight released by the number of pulses counted and the calibration procedure is finished The calculated value is displayed at the top of the screen note this figure if the computer is to be used with other seed drills using other calibration figures The value can be encoded directl
54. 300 RPM WARN WHEEL DRILL All other alarms require the wheel sensor to be generating pulses To avoid large bare patches should WARN the wheel sensor be damaged and therefore the computer receives no pulses even if the drill is lowered the warning WHEEL DRILL will be given after approx WH 15 seconds The warning is automatically removed DRI when the computer receives pulses from the wheel sensor or when the seed drill is raised Pressing the key will remove the warning for approx 15 seconds DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY 5 57 SEED DRILL LEMKEN TEEJET 5000 OPERATORS MANUAL NORMAL START As the motors used for altering the seed rate must be started at a certain level before being able to adjust the seed rate up or down it is necessary to decide at what speed the motors should start This is encoded as a forward speed The motor will start with the RPM required to sow at the given forward speed To encode the forward speed at which the motor should start at do as follows When this is shown in the display see page 5 xx press and hold the HOLD key for 5 seconds 2 Select START KM H and encode forward speed that motor should start at
55. ACCEPT NOTE NORDSTEN ELECTR Is only for NORDSTEN with electronic gearboxes It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 5 2 leefet 5000 OPERATORS MANUAL SEED DRILL OTHER SEED DRILL OPERATION OTHER TYPE Move between the two pages by pressing NEXT PAGE KG The amount sown in KG measured by a sensor fitted on the drill shaft Calibrating the system is necessary to ensure correct operation and this is done under ENCODE KG LEFT The amount in KG of seed left in the hopper the amount filled in must be encoded before work commences KG HA Seed rate in KG HA RPM RPM of an axle when this has been selected TRACK 1 Moves one step forward in the tramline rhythm TRACK 1 Moves one step backwards in the tramline rhythm HOLD KEY Press if the present bout is not required in the selected rhythm This function holds the present status regardless of how many times the drill is raised When this function is activated HOLD flashes on the display TRAMLINE INDICATOR No tramlines are mad
56. Bout number Track number The bout number is the present bout being driven in the field counts 1 each time the drill is lifted The track number is what has been encoded see ENCODE The TeeJet 5000 has 2 different methods of controlling the tramlines A and B The method is selected under ENCODE TRAMLINE INDICATION The second fixed function indicates on the display whether tramlines are being made or not TANNIN Tramlines are not being made Tramlines are being made KG HA The third function is the seed rate The seed rate is displayed in KG HA Seed rate Two arrows are displayed to the left of the display These arrows indicate whether the computer is adjusting the seed rate up or down Correct operation presupposes Correct calibration That the correct wheel circumference and working width has been encoded leefet 5 17 SEED DRILL NORDSTEN HOLD KEY TEEJET 5000 OPERATORS MANUAL Press if the present bout is not required in the selected rhythm This function holds the present status regardless of how many times the drill is raised When this function is activated HOLD flashes on the display SELECTABLE SEED DRILL FUNCTIONS The displayed function next to the function keys at the bottom of the unit display which functions are available KM H KG KG LEFT Forward speed in kilometres per hour with 1 decimal Forw
57. Different application rates for the two sides can only be achieved via the keys I When the area override sensor is activated not counting area 1 is displayed and all sections will disappear FERTILISER SPREADER FUNCTIONS There are 2 different function sets in this menu The displayed set depends whether automatic or manual application control has been selected as The following describes each function set individually leefet 4 115 FERTILISER DISTRIBUTOR RAUCH AXERA TEEJET 5000 OPERATORS MANUAL 1 AUTOMATIC APPLICATION CONTROL KG HA1 KG HA2 These 3 application rates are set in ENCODE and can be selected under OPERATION KG HA3 Pressing one of these keys displays the encoded required application rate Not the actual application rate Before accurate automatic application control can take place it is important to calibrate the system using the fertiliser to be spread Pressing the NEXT PAGE key displays the next functions HA Area KG Consumption in KG KG REST How many KG are left in the spreader at present HA Area counter Worked area since the last reset NOTE Total area counter is found in DATA DELETE KG Total KG used calculated from forward speed and gate position This function presupposes correct calibration NOTE Total KG counter is found in DATA DELETE KG LEFT
58. NEXT PAGE key displays the next functions RPM 1 Shaft speed of axle 1 START AND STOP SPREADING Pressing this key starts and stops the fertiliser spreader BOOM SECTION ON OFF The picture to the left shows a spreader with 2 sections where one is open and one is closed The total number of sections is set under encode When the area override sensor is activated not I counting area I is displayed and all sections will disappear leefet 4 27 FERTILISER DISTRIBUTOR BOGBALLE TEEJET 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements DOSERATE Encode the effective working width before encoding the application rate The required application rate is encoded in KG HA 4 28 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BOGBALLE CALIBRATION Calibrating t
59. REVS 4 72 4 73 DATE QNM M C ECCE E ee 4 73 4 61 FERTILISER DISTRIBUTOR BREDAL HYDR K TEEJET 5000 OPERATORS MANUAL INTRODUCTION TeeJet 5000 used to control the BREDAL K lime spreader Maintain the correct application rate regardless of forward speed plus the ability to alter the application rate in steps depending on the crop s requirement The TeeJet 5000 controls the application rate using a proportional valve that adjusts the amount of oil to a hydraulic pump which in turn alters the belt speed Visible and audible warnings given for incorrect rates forward speed PTO KG left etc NOTE The computer must be calibrated with the spreader to ensure correct operation This calibration must take place the first time the computer is connected to the spreader and each time the computer is connected to another spreader 4 62 5000 OPERATORS MANUAL BREDAL S LIME SPREADER
60. The tramline cannot be split over 2 bouts in this example with a rhythm of 4 encoded The first bout E can only be sown with one half of the drill open Q Once this is done the gt MEUM tramlines can be made i m with clutches fitted to the middle of the drill f Y Tramlines are made when the present bout UN number is the same as the encoded rhythm track number T T7 a Note where in the first 4 bouts around the whole field the bouts should N be counted A and Pi REI where bouts should not be counted all other corners 2 4 Jd d 1 a 4 Bout counting can be controlled by using either the HOLD key or by using the TRACK keys A Si leefet 5 69 SEED DRILL SIMBA TEEJET 5000 OPERATORS MANUAL SEED DRILL ENCODEMENT This menu allows the operator to encode the various settings that are necessary for sowing Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements mx e OU me QE gt
61. Total KG remaining in the hopper the amount must be encoded before start Pressing the NEXT PAGE key displays the next functions STEP Step dose rate AUTO MAN Change between automatic and manual application control 4 116 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH AXERA STEP Step dose rate NOTE Only active in automatic drift The application rate can be increased or decreased by an encoded percentile amount The rate can be altered for both sides or the left hand side or the right hand side by pressing the NEXT PAGE key see the following pictures When used the percentile increase or reduction flashes in the lower part of the display NORMAL AUTO MAN Pressing the NORMAL key returns the application rate to normal regardless of how many steps the rate has been increased or decreased by NOTE The step dose rate screen is left by pressing the return key Pressing this key changes between automatic and manual application control During manual operation flashes at the bottom of the display Pressing the NEXT PAGE key displays the next available functions POS Actuator position Reference figure for the gate posi
62. UNIFOVPRES S Gees Select 3 11 SPEED SENSOR KMYIH ierat nere nre enne adel ane eee 3 11 IMPLEMENT SENSOR Ehren ERE ERRprHE EEEE 3 11 PRESSURE SENSOR a ad bd ed 3 12 TANK VOLUME sre esee ati du estt t adeste 3 12 METRE eise ette 3 12 SYSTEM B PLUG ito erase ats cae e cee a eet eS Ao es tenders ety 3 12 Soe Steed eee tee int beide ec ae ed ed eed ed etc lain ORE 3 12 WORK HOUR kde eel ne eee 3 12 WARNINGS eee oe cee cae d ie ee a Bice A I C CI Cc ade 3 13 SPRAYER TEEJET 5000 OPERATORS MANUAL SPRAYER Select sprayer from the basic menu Move the cursor to Sprayer and press the Select function key it is now possible to choose between the 2 sprayer programs 1 HOLDER DC E5 special program for Holder sprayers with dose control manifold with motorised valves 2 OTHER TYPE used for all other sprayer types If the correct sprayer type is shown in Selected type menu press Accept Select another sprayer type by pressing SELECT TYPE then move the cursor to the required type an
63. eR ere eee 4 57 puse tiep rr UT 4 57 S TEP T c 4 57 FORWARD SPEED SENSOR 5 203 24 9 9 5 9 0 9 0 0 eb 4 58 WHEEL TRACTOR AND RADAR dose tide positi deponit 4 58 MEIRE SWI POH c 4 58 WORK HOUR ONORE etae en 4 58 REVS SENSOR ee me eee 4 58 2 2 4 59 cO 4 59 FOV FG TOR 4 59 4 59 4 47 FERTILISER DISTRIBUTOR BREDAL HYDR B TEEJET 5000 OPERATORS MANUAL INTRODUCTION TeeJet 5000 used to control the BREDAL B fertiliser spreader Maintain the correct application rate regardless of forward speed plus the ability to alter the application rate in steps depending on the crop s requirement The TeeJet 5000 controls the application rate using a proportional valve that adjusts the amount of oil to a hydraulic pump which in turn alters the belt speed Visible and audible warnings given for incorrect rates forward speed PTO KG left etc NOTE The computer must be calibrat
64. n n uuu gode 0 HH DH HM HU Im In Hg Hog dg EO dH oH HH Ep US HW HH HH EO dud ggg E numm H p H d M d Ht Za M n gt ake 5 46 Teglet 5000 OPERATORS MANUAL SEED DRILL LEMKEN Example of method F left The seed drill is fitted with 2x2 magnetic valves on the right hand side of the drill and 2x2 magnetic valves fitted to the left hand side of the drill Drilling is started on the left hand side of the field as shown on the diagram One half of the drill must be closed for the first bout Thereafter the track number should be set to 6 6 and tramlines are made on the right side of the drill Tramlines are made when the present track number is 1 3 4 amp 6 Note where tracks should be counted A and where tracks should not be counted all other corners in the first 3 bouts around the whole field Track counting can be controlled by using either the HOLD key or by using the TRACK keys a PIT P SSS a 77 279 727 SS 22 9 o aoe gt 2 7 ar ar 12121 212 231 a m maar
65. the amount filled into the seed drill must be encoded here NOTE If there is some seed left in the hopper before refilling then this amount must be added to the amount filled thus Amount left in hopper filled amount Kg left HA LEFT Encode the size of the field to be sown before work commences This encodement is also used to calculate end time SOW WIDTH The total working width of the seed drill is encoded here in centimetres 5 54 leefet 5000 OPERATORS MANUAL SEED DRILL LEMKEN TRACK NUMBER Encode the tramline rhythm here Example The working width of the seed drill is 3 m The working width of the fertiliser spreader sprayer is 15 m Track number 15 3 5 The tramlining method to be used is also selected here A B C D E F G H Right Left The methods are described in the seed drill operation section NOTE It is not possible to alter the track number if either method C D E F G or H have been selected as these methods have a set track number ROW NO Encode the total number of rows that the seed drill has NUMBER OF RETURNS If the seed drill is fitted with a return to tank when tramlines are made the number of tubes returning seed to the hopper should be encoded here If the seed drill is not fitted with a return to tank then this should be set to 0 ROWS IN TRACK Encode the number of rows that are shut when tramlines are being made This encodement is necess
66. the tank size is transferred to TON M3 REST and the slurry spreader is ready to fill and spread again This function is also used in conjunction with flowmeter calibration see page number 7 34 TON M3 MIN The amount of slurry per minute going through the flowmeter Pressing NEXT PAGE displays the next possible functions XX Step dosage increase XX Step dosage decrease NORMAL Return to the required normal application rate DOSE RATE Encoding the required application rate XX Percentile increase of the encoded application rate The size of the steps is altered in encode XX Percentile reduction of the encoded application rate The size of the steps is altered in encode NORMAL Only displayed if the step feature has been used Normal application rate Regardless of how many steps the application rate has been increased decreased by pressing this key will return the application rate to normal DOSE RATE Pressing this key allows the application rate to be altered directly from the operation screen see also DOSE RATE in encode Pressing the NEXT PAGE key displays the next functions RPM 1 Revolutions per minute RPM 1 The shaft speed of an axle is displayed here Normally the RPM of the distributor macerator Pressing the NEXT PAGE key displays the first set of functions 7 30 Teglet
67. value and the power can be measured on the meter 3 When the power is 100 mA Must not exceed 100 mA press CALIB CALC and the procedure is finished 4 The PWM value will be the highest value that can be reached by regulation 7 52 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER ZUNHAMMER PROPORTIONAL VAVE Select which porportional valve is fitted on the system in this menu 1 Select type 2 It is now possible to select between the shown valve types 3 Select valve 4 Accept 7 53 SLURRY SPREADER ZUNHAMMER TEEJET 5000 OPERATORS MANUAL WARNING ENCODE The following warnings can be set in this menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warning ON OFF and MAX MIN limits for wheel slip in RPM Warning ON OFF and MAX MIN limits for revolutions RPM 1 Warning ON OFF and MAX MIN limits for shaft speed Encode in RPM PLC Warning ON OFF for PLC warnings There are 4 PLC warnings given for the following No slurry flow High pressure Tank valve closed Fill pipe in NB The encoded limits must exceed the limits encoded If a warning is required when
68. 3 5 7 or 9 the system works well Tramlines are made using 2 clutches fitted in the middle of the seed drill when the present bout number is the same as the encoded track number See the drawing METHOD B UNEVEN If the tramlines are to be made on even bouts 2 4 6 or 8 then the operator must drive around the field with only one half of the seed drill open This is necessary as the tramlines cannot be split over 2 bouts The clutches are fitted in the middle of the seed drill and the tramlines are made in one bout See the drawing METHOD B EVEN FORWARD SPEED The forward speed is displayed in kilometres per hour with 1 decimal The forward speed is calculated from signals received from the sensor selected under ENCODE wheel tractor or radar 5 5 SEED DRILL OTHER METHOD A UNEVEN In the example to the right the encoded rhythm is 3 Two clutches are fitted in the middle of the drill NB Tramlines are made in bout number 2 when a rhythm track number of 3 is encoded Note where in the first 3 bouts around the field the present bout should A be counted and where the bout should not be counted After each trip around the field the machine drives in the opposite direction Bout counting can be controlled by using either the HOLD key or by using the TRACK keys TEEJET 5000 OPERATORS MANUAL 3 VE ses 3
69. 4 bouts around the whole field Bout counting can be controlled by using either the HOLD key or by using the keys OOA 20000 2 TART 5 42 leefet 5000 OPERATORS MANUAL SEED DRILL LEMKEN Example of method D Left The seed drill is fitted with 2x2 magnetic valves on the right hand side of the machine and 2x2 magnetic valves fitted on the left hand side of the machine Drilling is started on the left hand side of the field as shown on the diagram with a track number of 1 18 Tramlines are made when the actual track number is 3 7 12 and 16 Note where the bouts should be counted A and where bouts should not be counted all other corners in the first 4 bouts around the whole field Bout counting can be controlled by using either the HOLD key or by using the TRACK keys m e O00 TART 5 43 SEED DRILL LEMKEN TEEJET 5000 OPERATORS MANUAL METHOD E This method is used when the seed drill is 6 metres wide and
70. 5000 OPERATORS MANUAL Pressing the NEXT PAGE key displays the next functions OFFSET AUGER OFFSET XX RPM AUGER OFFSET AUGER Offset increase decrease OFFSET XX Offset increase only shown if OFFSET AUGER is activated OFFSET Offset decrease only shown if OFFSET AUGER is activated RPM AUGER Auger speed Offset ON OFF When this key is pressed the OFFSET function is activated Step increase or decrease This function is only shown if the OFFSET function is activated The size of the offset steps is encoded in the service menu see encode The OFFSET function is used to alter the standard auger speed The auger speed is determined by a curve in relation to the application rate The auger speed is altered when the application rate is altered and changing the OFFSET changes the relation between auger speed and the application rate Pressing this key displays the auger speed in RPM Pressing the NEXT PAGE key displays the next functions MANUAL START Manual auger start EMPTY AUGER Emptying the auger MANUAL START The belt and auger run for 30 seconds when this key is pressed The runs at a speed co responding to a forward speed of 8 kph and the auger turns with 250 RPM Manual start is cancelled after 30 seconds or when the forward speed is over 3 kp
71. 7 Each function will be described later in this section The picture to the left is displayed the next time the TeeJet 5000 is switched on Communication between the DataLink module and the TeeJet 5000 is being established WAITING DATALINK If DGPS functions are not required then pressing TeeJet 5000 MODE key will allow the TeeJet 5000 to operate as normal When DGPS functions are required again following the procedure described from the top of this page will switch the DGPS functions on again Telet 9 3 DGPS TEEJET 5000 OPERATORS MANUAL DGPS STATUS DG is displayed when satellite and reference D G signals are being received If positional signals are only being received from eller satellites then G will be displayed Pressing the STATUS key on the TeeJet 5000 displays the present DGPS Status E Latitude The position is shown in degrees minutes and ten thousandths of a minute N Longitude The position is shown in degrees minutes and ten thousandths of a minute H Altitude The height in metres from sea level NAV MODE Tells the operator whether there is only signals from satellites GPS or if reference signals are also being received DGPS NO OF SATELLITES The number of satellites that signals are being received from PDOP The distance b
72. BOM 1 12 Error is displayed as boom Error is displayed as no boom interface is connected interface is connected TEST OUTPUT OUT 1 Signal to close the gates Signal to close the gate OUT 2 Signal to open the gates Signal to open the gate OUT 3 Not used Not used OUT 4 Not used Not used POT1 2 POT 1 shows the position of the Shows the position of the actuator Lowest value when the actuator Lowest value when the gates are closed POT 2 is not gate is closed highest value used when the gate is open Teglet 2 23 GENERAL FUNCTIONS TEEJET 5000 OPERATORS MANUAL TEST INPUT BREDAL HYDRAULIC BREDAL K RAMP TRAIL 1 Signal from RPM sensor fitted to Signal from RPM sensor fitted to the spinning discs the spinning discs TRAIL 2 Signal from weigh cells Signal from weigh cells TRAIL 4 Speed signal from sensor fitted Speed signal from sensor fitted to spreader wheel to spreader wheel TRAIL 7 Signal from RPM sensor fitted to Signal from RPM sensor fitted to the hydraulic motor the belt hydraulic motor TRAIL 8 Not used Signal from RPM sensor fitted to the auger hydraulic motor TRAIL 15 Not used Not used TRAIL 16 Not used Not used BOM 1 12 Error is displayed as no boom Error is displayed as no boom interface is connected interface is connected TEST OUTPUT OUT 1 Completely opens the Completely opens the belt proportional valv
73. CALIBRATION 4 96 cs eer DEN 4 99 KG LEF pm 4 99 RALE uj e 4 99 METRE SWITCH 4 99 WORK HOUR ON OFF a perna Face Fe er 4 99 PTO SENSOR d ee 4 100 WARNING ENG OD cm 4 100 e eee 4 100 Teglet 4 89 FERTILISER DISTRIBUTOR RAUCH AERO TEEJET 5000 OPERATORS MANUAL RAUCH AERO FERTILISER DISTRIBUTOR 1 Select fertiliser distributor from the main menu as follows 2 Move the cursor using the arrow keys to FERTIL DISTRIB Press the SELECT key 3 Main menu select fertiliser distributor 4 ACCEPT or SELECT TYPE 5 Select type 6 It is now possible to choose between the displayed types 7 Select fertiliser distributor type 8 Accept type It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK O
74. EMPTY The value encoded under TANK VOLUME will be automatically transferred to TON M3 LEFT DAILY USE OF THE SLURRY PROGRAM WITHOUT A FLOWMETER Once all of the encodements have been accepted proceed as follows Start spreading and each time the area override sensor is activated implement sensor the following warning is displayed When this screen is displayed you have the following options If the machine is turning at the headland then continue driving and the warning screen will disappear when spreading starts again If you stop spreading temporarily without the tank being empty press PAUSE to remove the warning The warning screen will disappear when spreading starts again If the tank is empty press TANK EMPTY The following 2 things will happen automatically TANK VOLUME is transferred to TON M3 counter TANK VOLUME is added to the total counter for consumed amount which can be found in DATA DELETE 7 32 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER HORSCH CALCULATING M3 HA OR TON HA Each time EMPTY TANK is pressed the TeeJet 5000 calculates the amount spread with this tank full This makes it possible to find the correct forward speed PTO RPM and therefore the application rate for the last 1 2 loads An accurate calculation demands a const
75. ID NO key allows the operator to encode an ID Number this number could e g be a number that identifies a customer or an employee It does not matter when the ID number is encoded but the task BIS must be started As the computer uses the task number for its own reference it is not necessary to encode an ID Number if this is not required Use the numeric keypad to encode the ID number The ID number can be deleted at any time by pressing the key Pressing the return key displays the previous menu STOP TASK Pressing this function key will stop the present task it is possible to open the task again at any time as long as the task is still in the computer s memory NOTE It is not possible to exit the implement menu if a task is active The computer displays the following message MENU CHANGE NOT PROHIBITED and shows which task should be stopped before the implement menu can be changed SEE TASK Pressing the See Task function key displays the picture to the left Move the cursor to the task to be seen and press the See Task function key It is now possible to see the contents of the task without having to start the task NOTE All tasks that contain data can be seen regardless of the implement selected for operation so it is possible to see tasks for e g slurry spreader even if the implement chosen for operation is a s
76. METHOD H This method is used when the seed drill is 6 metres wide and the implement used to cultivate the crop is 39 metres wide A fixed rhythm of 26 is used see page 5 55 Example of method H Right The seed drill is fitted with 2x2 magnetic valves on the both sides of the seed drill Drilling is started on the right hand side of the field with the track number set to 1 26 as shown on the diagram After the first bout around the field change direction to drive the other way around the filed do this for the third and fourth bout also Tramlines are made when the present track number is 4 10 17 and 23 Note where tracks should be counted A and where tracks should not be counted all other corners in the first 4 bouts around the field Track counting can be controlled by using either the HOLD key or by using the TRACK keys 2 26 1 26 26 26 25 26 24 26 23 26 22 26 21 26 20 26 19 26 18 26 15 26 14 26 13 26 12 26 11 26 10 26 9 26 8 26 7 26 6 26 5 26 4 26 3 26 2 26 1 26 2 n rag START 5 50 Teefet 5000 OPERATORS MANUAL SEED DRILL LEMKEN Example of method H Left The seed drill is fitted with 2x2 magnet
77. NEXT PAGE key displays the first available functions SECTION ON OFF The picture to the left shows a spreader with 2 sections encoded where one is open and one is closed The total number of sections is set under encode When the area override sensor is activated not counting 1 area is displayed sections will disappear 4 128 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR REI FERTILISER DISTRIBUTOR ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements DOSE RATE The required application rate is encoded in TON HA LOGGING The date and flow tons min are registered every other minute Registration of data will only take place if the spreader is operating area override sensor not activated and the consumption is minimum 0 1 ton per minute Pressing the LOG DATA key displays the data that has
78. NORDSTEN TEEJET 5000 OPERATORS MANUAL NORDSTEN ELECTRONIC SEED DRILL 1 Select drill from the main menu 2 Move the cursor using the arrow keys to DRILL when this is done press the SELECT key 3 Main menu Drill 4 ACCEPT the selected type or choose another type 5 Select type 6 It is now possible to choose between the displayed types 7 Select the drill type 8 ACCEPT NOTE NORDSTEN ELECTR Is only for NORDSTEN drill with electronic gearboxes It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 5 16 leefet 5000 OPERATORS MANUAL SEED DRILL NORSTEN FIXED FUNCTIONS TRAMLINE CONTROL The primary function for seed drills is the track number The following picture is displayed RACK NO
79. PAGE key displays the next functions RPM 1 Weighing in KG using weigh cells fitted on the spreader only displayed if WEIGHING ON is selected under encode RPM BELT Tarring the weigh cells this key must be held down for approx 3 seconds only displayed if WEIGHING ON is selected under encode Pressing the NEXT PAGE key displays the next functions WEIGHT Weighing in KG using weigh cells fitted on the spreader only displayed if WEIGHING ON is selected under encode TARRING Tarring the weigh cells this key must be held down for approx 3 seconds only displayed if WEIGHING ON is selected under encode Using weighing if the system is fitted with weigh cells Calibrating the weigh cells is a condition for correct operation The calibration procedure is described under ENCODE leefet 4 65 FERTILISER DISTRIBUTOR BREDAL HYDR TEEJET 5000 OPERATORS MANUAL 1 Press TARRING for approx 3 seconds whilst at a standstill WEIGHT will change to 0 which is the same as 0 KG There are 2 possibilities a Start spreading with the weight displayed and at each weighing the amount left in the spreader can be seen b Each time TARRING is pressed for approx 3 seconds with something in the spreader the displayed KG will be O It is now possible to see how much has been used neg
80. Radar and the number of pulses per metre will be displayed at the top of the screen IMPORTANT Working in crops that are blowing in the wind or working in areas with surface water can affect the accuracy of the radar we recommend using a speed sensor fitted to the tractor under these circumstances WHEEL SLURRY SPREADER If the slurry spreader is fitted with a speed sensor then press the WHEEL SLURRY key The TeeJet 5000 will now use this sensor for forward speed measurement Please refer to chapter 2 for forward speed calibration IMPLEMENT SENSOR This sensor starts and stops the area counter A pressure sensor should be fitted on slurry spreaders between the pump and the distributor macerator so that the sensor generates a signal when the pressure drops If this is the case then SLURRY SPREADER should be selected If a sensor for PTO speed is fitted then this can be used as an area override sensor select PTO METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor IMPLEM SENSOR WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor 7 50 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER ZUNHAMMER REVS SENSOR Encode the number of pulses per revolution given for the individual sensor
81. SEED DRILL FUNCTIONS KM H Forward speed in kilometres per hour KG The amount sown in KG KG LEFT The amount in KG of seed left in the hopper KM H KG KG LEFT Forward speed in kilometres per hour with 1 decimal Forward speed is measured from the sensor selected under ENCODE The amount sown in KG measured by a sensor fitted on the drill shaft Calibrating the system is necessary to ensure correct operation and this is done under ENCODE The amount in KG of seed left in the hopper the amount filled in must be encoded before work commences Pressing the NEXT PAGE key displays the next available functions Step increase XX Step decrease NORMAL Returns to normal seed rate XX XX NORMAL Step increase of the desired seed rate in steps The size of the steps are encoded in ENCODE Step decrease of the desired seed rate in steps The size of the steps are encoded in ENCODE Normal seed rate Regardless of how many steps the application rate has been increased decreased by pressing this key will return the application rate to normal Pressing the NEXT PAGE key displays the next available functions 5 34 leefet 5000 OPERATORS MANUAL SEED DRILL LEMKEN RPM Fan Speed VALVE RPM Regulating motor spee
82. TYPE 4 Select type 5 Itis now possible to choose between the displayed types 6 Select fertiliser distributor type 7 Accept type It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 4 114 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH AXERA H FERTILISER DISTRIBUTOR OPERATION FORWARD SPEED The primary function under fertiliser distributor is forward speed Forward speed is displayed in KPH with 1 decimal Forward speed is calculated from the signal from the speed sensor selected in encode wheel tractor wheel sprayer or radar SPREADER SECTION INDICATION The picture to the left shows a 2 section spreader with 1 section closed and 1 section open The number of sections can be changed in ENCODE The figure to the right indicates which calibration is being used REQUIRED APPLICATION RATE The second function is the required application rate If there is a difference between the right and the left hand side this will also be displayed An arrow is displayed on the left of the screen indicating which way the regulating device is moving NOTE
83. again Refer to the documentation supplied with the spreader for further information 1 The required application rate is encoded by moving the cursor to DOSE KG HA Use the numerical keypad 2 Encode the specific gravity found using the specific gravity tester from Bredal 3 Pressing CALC CALIB calculates the settings for scale gear and PTO When DOSERATE has been selected the screen cannot be left until CALIB CALC has been pressed The required application rate together with the specific gravity and the working width gives Scale setting The correct gear on the spreader PTO revolutions Minimum RPM for the RPM 1 alarm WARNING These settings must therefore be calculated again each time the spreader width is changed 4 41 FERTILISER DISTRIBUTOR BREDAL Newer spreaders TEEJET 5000 OPERATORS MANUAL If the spreader used is not appropriate with the spreader table programmed into the computer it is possible to encode the scale settings using the spreader table supplied with the spreader Scale setting encodement is done as follows Read the settings from the table supplied with the spreader Encode the effective spreader width under DISTRIB WIDTH Sele
84. an axle stops 0 RPM then set the minimum limit to 1 Besides these warnings an automatic rate warning is given if the application rate varies from the encoded by 20 DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY 7 54 Teglet Other Implement OURER MMPLEMEN dee ud tiled etna el lol ud ai lin ed 8 2 OTHER IMPLEMENT OPERATION 8 3 Bis Ise1ye le 8 3 OTHER IMPLEMENT lt 8 4 inui zii T 8 4 WORKING WIDTH ge ote 8 4 2 tn ate e aont dea ee 8 5 IMPLEMENT SENSOR 8 5 METRE SWITCH S GS M 8 5 8 5 ajerc lepq e 8 6 a Ci 8 6 US 8 6 OTHER IMPLEMENT TEEJET 5000 OPERATORS MANUAL OTHER IMPLEMENT Select OTHER IMPLEMENT from the main menu as follows Move the cursor using the arrow keys to OTHER IMPLEMENT when this is done press the SELECT key 2
85. be fitted next to the existing trailer plug as shown below Lift arm movement must be considered when fitting the breakaway plug A a CABLE ROUTING Lead the cables from the various sensors and breakaway plug together with existing cables hydraulic pipes etc to the junction box Attach the cables with the supplied cable binders Be careful not to route the cables near moving parts sharp edges and areas with high temperatures etc 12 12 Teglet 5000 OPERATORS MANUAL FITTING INSTRUCTIONS CONNECTIONS IN THE JUNCTION BOX A label is supplied in the fitting kit attach this label to the lid of the junction box to ensure that the connections are always available when if the system is added to at a future date White Trail 1 2 Brown OV rown Trail 2 Implement reen 4 Brown OV TeeJet 5000 1 Brown Mot 1 Yellow Blue Imple e Violet LI LL LLL LL EEECLELELE 0 lt 4 5 12 Trail 7 12V Wheel O reen 10 Brown OV 10 Black 11 Bue 12V Blue Peay 12 Blue Red OV FUSE 4A eje White Green lee e Technologies MULTI CABLE FROM THE TEEJET 5000 Connect this cable to connecting block 1 Connect the individual wires according to the colour code on the label MULTI CABLE FROM THE BREAK AWAY PLUG Connect to connecting block 2 1 7 according to
86. be selected under OPERATION KG HA3 Pressing one of these keys displays the encoded required application rate Not the actual application rate Before accurate automatic application control can take place it is important to calibrate the system using the fertiliser to be spread To minimize the risk of incorrect operation application the following automatic warnings may be displayed DOSERATE If the required application rate can not be achieved Pressing the NEXT PAGE key displays the next functions HA Area KG Consumption in KG KG REST How many KG are left in the spreader at present HA Area counter Worked area since the last reset NOTE Total area counter is found in KG Total KG used calculated from forward speed and gate position This function presupposes correct calibration NOTE Total KG counter is found in KG REST Total KG remaining in the hopper the amount must be encoded before start Pressing the NEXT PAGE key displays the next functions 4 104 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH BETA DELTA STEP RPM POS AUTO MAN STEP Step dose rate RPM for the spinning discs or the position of the actuator depending on which program has been s
87. because the spinner discs suck fertiliser out of the hopper The application rate is encoded to 200 kg ha but after spreading 10 ha 2100 kg has been spread this difference of 100 kg is equal to 5 Setting the OFFSET value moves the calibration so that the spread amount is the same as the calibrated application rate In the above example the OFFSET value should be changed to 0 95 If the amount spread was 5 low the above example then the OFFSET value should be altered to 1 05 4 112 Fertiliser distributor Rauch Axera H RAUCH AXERA H FERTILISER 4 114 FERTILISER DISTRIBUTOR OPERATION 4 115 FERTILISER SPREADER FUNCTIONS 4 115 1 AUTOMATIC APPLICATION nenne 4 116 2 MANUAL APPLICATION CONT ROD iiit quoquc opc tse n Eurus idus 4 118 FERTILISER DISTRIBUTOR ENCODE deesse 4 119 WORKING WID TR rr UTE 4 119 SPEED SENSOR e ee ce eee ee 4 120 WHEEL TRACTOR HO 4 120 WHEEL SPREADER 4 120 Dipl 4 120 FERTILISER CALIBRATION 4 120 FERTILISER CALIBRA ION
88. calculation demands a constant forward speed and PTO speed and correct encodements SLURRY SPREADER ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements DOSERATE Encode the required application rate if automatic application control equipment is fitted or if a warning is required for incorrect application rate Encode the required rate in TON or M3 cubic metres per hectare The maximum rate that can be encoded is 99 99 Change between TON by pressing the key STEP Encode the size of the steps for the STEP function This value is the same for both and The maximum step size is 9996 Telet 7 47 SLURRY SPREADER ZUNHAMMER TEEJET 5000 OPERATORS MANUAL TANK VOLUME Encode the effective size of the tank here Check if possible by
89. data all you have to do is open this file and all the settings will be correct Teglet 2 13 GENERAL FUNCTIONS TEEJET 5000 OPERATORS MANUAL RECEIVE TEXT The TeeJet 5000 sends a fully formatted text file as a txt type file This file is received in Terminal or Hyper Terminal and can then be saved wherever you wish It is recommended to make a folder specifically for the TeeJet 5000 to ease management of these files Receive Text File Ea File Name Directories Cancel bw565 txt Ih565 txt X termina Append File Save Controls List Files of Type Drives Table Format Text files TXT 23 m Figure 7 Screen shot of transfers receive text file Windows Terminal Capture Text Folder C Program Files Accessories HyperT erminal File cessories H yperT erminal LH5000 T lt T Browse teca Figure 8 Screen shot of transfers capture text Hyper Terminal 21 Terminal LH5000 TRM x Eile Edit Settings Phone Transfers Help IMPLEM SPRAVER 4 ID 25 TASK 1 LITRE 2188 11 5 LITRE HR 183 START 28 12 96 11 85 STOP 28 12 96 11 28 8 21 Figure 9 Screen shot of sprayer task 2 14 5000 OPERATORS MANUAL GENERAL FUNCTIONS EDITING THE TEXT Once saved in the PC It is possible to edit these text files in almost any word processing program that can open txt files
90. drill s effective working width in Cm FORWARD SPEED SENSOR The TeeJet 5000 V 4 seed drill program Simba gives the option of choosing between three different speed sensors Wheel tractor wheel drill or Radar WHEEL TRACTOR The speed signal can come from a sensor fitted in the gear box or on a drive shaft or from a sensor fitted on a wheel depending on the make and model of the tractor used for sowing WHEEL DRILL If a speed sensor is fitted on the seed drill then use this sensor as the sensor will give a suitable number of pulses RADAR If the tractor is fitted with radar then select RADAR and forward speed will be measured from the radar Radar and the number of pulses per metre will be displayed at the top of the screen Please refer to chapter 2 for forward speed calibration IMPLEMENT SENSOR The implement override sensor starts and stops area counting and counts bouts Pressing this key gives the following options 1 3 point external lift arms 2 3 point DIN ISO built into the tractor 3 Seed drill The selected sensor is shown at the top of the display 5 72 leefet 5000 OPERATORS MANUAL SEED DRILL SIMBA METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor IMPLEM SENSOR WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu o
91. either the HOLD key or by using the TRACK keys th up 7 5 9 SEED DRILL OTHER TEEJET 5000 OPERATORS MANUAL SEED DRILL ENCODEMENT This menu allows the operator to encode the various settings that are necessary for sowing Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements OU me QE gt Qe OI f gt KG LEFT To see how much seed is left in the hopper the amount filled into the seed drill must be encoded here NOTE If there is some seed left in the hopper before refilling then this amount must be added to the amount filled thus Amount left in hopper filled amount Kg left HA LEFT Encode the size of the field to be sown before work commences This encodement is also used to calculate end time TRACK NUMBER Encode the tramline rhythm here Example The working width of the seed drill is 3 m The working width of the fertiliser spreader sprayer is 15 m
92. for axle no 1 choose when fitting the system A warning can be set on or off plus the number of pulses per rev are set under ENCODE UNITS The number of bales counted is displayed in OPERATION as a trip counter A total counter is found under DATA DELETE both counters are deleted in TARRING Pressing this key zero sets the weighing system the weight must be empty The weighing system must be calibrated as described in the ENCODE section SWITCHING ALL WARNINGS OFF Pressing the HOLD key switches all warnings off R is displayed in the bottom left hand side of the display The warnings can be switched on again by pressing the HOLD key once more 6 4 Teefet 5000 OPERATORS MANUAL BALER BALER ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements WEIGHING Selecting this encodement gives you 2 options 1 WEIGHING 2 RPM3 WEIGHING bale weight A new function key is displayed when weighing is selected CALIB CALC CALIBRATION Pressing this key disp
93. if MAN has been selected under in encode AREA MEASUREMENT The worked area is displayed in Ha Area is displayed with 2 decimals from 0 to 99 99 ha And thereafter with 1 decimal from 100 to 999 0 ha NOTE a total counter for area can also be found in DATA DELETE LIME SPREADER FUNCTIONS TON HA RPM 1 Application rate in TON HA The speed of a RPM sensor fitted to the spreader if MAN has been selected under encode TON Lime consumption in tons TON LEFT Tons remaining in the hopper the amount must be encoded before starting XX Step dosage increase Step dosage decrease DOSE RATE NORMAL Encoding the required application rate or return to normal after using the step key 4 64 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL HYDR XX Percentile increase of the encoded application rate The size of the steps is altered in encode XX Percentile reduction of the encoded application rate The size of the steps is altered in encode NORMAL Only displayed if the step feature has been used Normal application rate Regardless of how many steps the application rate has been increased decreased by pressing this key will return the application rate to normal DOSE RATE Pressing this key allows the application rate to be altered directly from the operation screen see also DOSE RATE in encode Pressing the NEXT
94. increased decreased by pressing this key will return the application rate to normal DOSE RATE Pressing this key allows the application rate to be altered directly from the operation screen see also DOSE RATE in encode Pressing the NEXT PAGE key displays the next functions WEIGHT Weighing in KG using weigh cells fitted on the spreader only displayed if WEIGHING ON is selected under encode TARRING Tarring the weigh cells this key must be held down for approx 3 seconds only displayed if WEIGHING ON is selected under encode RPM BELT Belt speed in RPM Using weighing if the system is fitted with weigh cells Calibrating the weigh cells is a condition for correct operation The calibration procedure is described under ENCODE Press for approx seconds whilst at a standstill WEIGHT will change to 0 which is the same as 0 KG There are 2 possibilities a Start spreading with the weight displayed and at each weighing the amount left in the spreader can be seen b Each time TARRING is pressed for approx seconds with something in the spreader the displayed KG will be O It is now possible to see how much has been used negative weighing It is not possible to see how much fertiliser is left in the spreader 4 79 FERTILISER DISTRIBUTOR BREDAL K RAMP TEEJET
95. main menu as follows 1 Move the cursor using the arrow keys to FERTIL DISTRIB Press the SELECT key 2 Main menu select fertiliser distributor 3 ACCEPT or SELECT TYPE 4 Select type 5 It is now possible to choose between the displayed types 6 Select fertiliser distributor type 7 Accept type It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 4 25 FERTILISER DISTRIBUTOR BOGBALLE TEEJET 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR OPERATION FORWARD SPEED The primary function under fertiliser distributor is forward speed Forward speed is displayed in KPH with 1 decimal Forward speed is calculated from the signal from the speed senso
96. model of the tractor used for fertiliser spreading WHEEL SPREADER If the spreader is fitted with a speed sensor press the WHEEL SPREADER key The TeeJet 5000 will now receive speed signals from the sensor fitted to the spreader and gives as a rule a very accurate speed reading RADAR Working in crops that are blowing in the wind or working in areas with surface water can affect the accuracy of the radar we recommend using a speed sensor fitted to the tractor or spreader under these circumstances Please refer to chapter 2 for speed sensor calibration IMPLEMENT SENSOR Using 1 of the following 3 options select how the area counter is to be switched on and off 1 LIFT 2 FERTILISER DISTRIBUTOR 3 PTO The selected sensor is shown at the top of the display METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor IMPLEM SENSOR 4 10 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR OTHER SYSTEM B PLUG There are 2 system plugs on the back of the TeeJet 5000 The System A plug is compatible with o der TeeJet 5000 versions The System B plug is for new connections ACTIVE 0 VOLT _ The individual sections are opened with OV 12 VOLT The individual sections are opened with 12V ON OFF ON The system B plug is used OFF The system B plug is not used WORK HOUR ON OFF Select whether the timer
97. motor etc This warning disappears when there is no longer a short circuit WARN DATA ERROR Displayed when a fault occurs in encodements and counters This warning can be removed by pressing the RETURN key Check all encodements if the problem persists please contact your local dealer WARN ACTUATOR ERROR Displayed when a problem occurs with an actuator on a fertiliser spreader Check the wiring if the problem persists please contact your local dealer 2 34 Teejet Sprayer i a ala ra Gas erate 3 2 SPRAYER OTHER TYPE 3 3 SPRAYER OPERATIONS erro pb ad n mesi Amd a a 3 3 SPRAYER F UNGTIONS tete niet e dtes 3 4 EXTRA TRACTOR FUNCTIONS IN THE SPRAYER 3 6 BOOM SECTION ON OFF cte tette beri teinte ce ees eee ERR cei ena iE 3 7 FILLING FUNCTION 3 7 a duod ieu tse 3 9 e t usted oda 3 9 STEPS eiae i Me ASIE 3 9 LITRE EBP ecc C 3 9 PUPAE EA E 3 10 FLOW FIGURE vein cene UEM URINE Dura pdS 3 10 BOOM WIDTH Mee ETE 3 11 DRIVESEAGTORR id nitet dip Sud tto od toin toa todo Emule Angl 3 11 REGULATION DEVAN coe det 3 11
98. qe 5 11 SOW WID T 5 11 2 22 5 12 WHEEL YS 0 SN CIEL 5 12 RADAR M 5 12 IMPLEMENT SENSOR a dee 5 12 METRE SWITCH Pete 5 12 WORK HOUR ON OFF m X M 5 12 REVS SENSOR O 5 13 ruri CIE ee ll 5 14 p Xp E oe 5 14 Teejet 5 1 SEED DRILL OTHER DRILL OTHER TYPE TEEJET 5000 OPERATORS MANUAL Select seed drill from the main menu as follows 1 Move the cursor using the arrow keys to DRILL when this is done press the SELECT key 2 Main menu Drill 3 ACCEPT the selected type or choose another type 4 Select type 5 It is now possible to choose between the displayed types 6 Select the drill type 7
99. rei beet teat mu Pet hee Pea ou tese ee Det 5 15 SEED DRILL LEMKEN 5 oriente otn entooe trek ob nee end ERR ER SA 5 31 SEED DRILL SIMBA 5 61 em 6 1 SLURRY SPREADER OTHER TYPE rue sees 7 1 SLURRY SPREADER HYDRAULIC 7 15 SLURRY SPREADER e coke eee cet n en 7 27 SLURRY SPREADER ZUNFAMM Reser acetate 7 41 NE 8 1 DGPS cad 9 1 INTRODUCTION Welcome to many hours of pleasurable work with your new TeeJet 5000 Multi Implement Computer We recommend that you read at least the general information chapters in this manual before you start using the computer Please remove the implement chapters in this manual that you do not require but don t throw them away as you will need them again when you expand your TeeJet 5000 system We have tried to write this manual as readable as possible using as little computer talk as possible Please read chapters 1 and 2 sit in the cab with this manual switch the computer on and page your way
100. s setup the amount released and the encodements are correct If the above is correct then the following can be done If the fertiliser being used has been stored for a long time then the fertiliser could be damper or drier than when the spreader was calibrated these conditions can affect the accuracy of the system This can be corrected by altering the amount released by the same percent that the amount spread deviates from the required amount Lower released KG higher application rate ACTUATOR CALIBRATION The spreader s actuator and the TeeJet 5000 must be setup together Calibrating the system does this Calibrate the system at regular intervals i e each time the spreader has been disconnected from the computer Before calibration The handle s stop must be set and tightened exactly on the scale s last figure Ensure that the handle stop cannot move whilst calibrating CALIBRATING 1 Press the CALIB CALC key for min 3 seconds this moves the handle to the open position then back to the closed position Control To ensure that the actuator and computer are calibrated correctly perform a release test with an empty hopper The handle should open to 4 5 for the E and EX models and 3 5 for the D DZ models NOTE It may be necessary to repeat the actuator calibration a few times if the actuator has been removed to achieve the correct position during a release test 4 3
101. selected The tractor info functions are FORWARD SPEED WHEEL SLIP DIESEL CONSUMPTION PER HOUR WORK EFFICIENCY AREA REMAINING AREA Press the RETURN KEY to revert to previous screen Pressing this key allows the screen contrast dark light to be adjusted This ensures that the information on the screen can be seen under all conditions NOTE extreme heat or cold may cause the screen to appear black or totally blank Using the CONTRAST key allows for this to be compensated for but when the TeeJet 5000 reaches normal operating temperature the screen will again become un readable The present contrast is shown at the top of the display Normal contrast is 45 50 Contrast darker display Contrast brighter display Pressing the C key sets the contrast to 50 1 3 GENERAL USE MEMORY KEY HOLD KEY DELETE KEY BACKGROUND LIGHT NUMERICAL KEYS 0 9 TEEJET 5000 OPERATORS MANUAL The memory keys works as a bookmark Pressing this key stores the currently selected screen After moving around through the menus simply pressing the memory key again will return the screen to the previously selected screen NOTE The MEMORY KEY works only within one implement at a time e g sprayer This key has different functions depending on the implement selected Hold key on seed drill Fill flow menus for sprayers Start and stop for certain fertiliser distributors The d
102. the PTO axle when turning WHEEL TRACTOR Signal from the wheel sensor when driven slowly forward DIESEL Signal from the diesel flowmeter when diesel is being used IMPLEM Signal from the implement sensor when raised e g the lift switch or a sensor fitted on the lift arms BOOMTEST One of the two following can be displayed OK The boom section interface is connected correctly ERROR No boom section interface connected or when there is a fault in the system Q Q Q Q OW OU Pe OW OU OU OU OU OU OU OU Teglet 2 21 GENERAL FUNCTIONS TEST INPUT OUTPUT SPRAYER TEEJET 5000 OPERATORS MANUAL TEST INPUT SPRAYER OTHER TYPE HOLDER TRAIL 1 Signal from pressure sensor Signal from pressure sensor TRAIL 2 Signal from sprayer Signal from sprayer flowmeter Turn the paddle flowmeter Turn the paddle wheel by hand or let the wheel by hand or let the sprayer spray sprayer spray TRAIL 4 Signal from the wheel sensor Signal from the wheel sensor fitted on a trailed sprayer fitted on a trailed sprayer TRAIL 7 Signal from the sprayer s Signal from t
103. the implements used to cultivate the crop are 21 metres wide A fixed rhythm of 14 is used see TRACK NUMBER page 5 55 Example of method E Right The seed drill is fitted with 2x2 magnetic valves on the right hand side of the machine and 2x2 magnetic valves fitted on the left hand side of the machine Drilling is started on the right hand side of the field as shown on the diagram with a track number of 11 14 Tramlines are made when the actual track number is 2 6 9 and 13 Note where the bouts should be counted A and where bouts should not be counted all other corners in the first 4 bouts around the whole field Bout counting can be controlled by using either the HOLD key or by using the keys 3T no 116 5 44 5000 OPERATORS MANUAL SEED DRILL LEMKEN Example of method E Left The seed drill is fitted with 2x2 magnetic valves on the right hand side of the machine and 2x2 magnetic valves fitted on the left hand side of the machine Drilling is started on the left hand side of the field as shown on the diagram with a track number of 11 14 Tramlines are made when the actual track number is 2 6 9 and 13
104. the spreader The individual section width boom compensation must be encoded here left boom section 1 If the spreader does not have individual sections then encode the whole spreader width as section 1 all other sections must be encoded as 0 DRIVE FACTOR DRIVE FACTOR The speed at which the regulating valve adjusts to maintain the correct application rate Min 1 and Max 500 Normal 25 If the spreader takes too long to find the required application rate then the drive factor should be increased If the spreader constantly changes from too much to too little then the drive factor should be reduced REG TIME Encode the number of seconds that the regulating system may move in one direction The normal setting is 10 RETURN If the spreader is fitted with a return return to tank after the flowmeter or not ON YES OFF NO Teejet 7 23 SLURRY SPREADER OTHER TYPE HYDR TEEJET 5000 OPERATORS MANUAL FORWARD SPEED SENSOR The TeeJet 5000 V 4 slurry spreader program gives the option of choosing between 3 different speed sensors Wheel tractor Wheel spreader Radar WHEEL TRACTOR The speed signal can come from a sensor fitted in the gear box or on a drive shaft or from a sensor fitted on a wheel depending on the make and model of the tractor used for slurry spreading RADAR If the tractor is fitted with radar then select RADAR and forward speed will be measured from the radar Radar an
105. the step feature has been used Normal application rate Regardless of how many steps the application rate has been increased decreased by pressing this key will return the application rate to normal DOSE RATE Pressing this key allows the application rate to be altered directly from the operation screen see also DOSE RATE in encode Pressing the NEXT PAGE key displays the next functions WEIGHT Weighing in KG using weigh cells fitted on the spreader TARRING Tarring the weigh cells RPM 1 Shaft speed of axle 1 Using weighing if the system is fitted with weigh cells Calibrating the weigh cells is a condition for correct operation The calibration procedure is described under ENCODE Press TARRING whilst at a standstill WEIGHT will change to 0 which is the same as 0 KG There are 2 possibilities Start spreading with the weight displayed and at each weighing the amount left in the spreader can be seen Each time TARRING is pressed the displayed KG will be 0 It is now possible to see how much has been used negative weighing It is not possible to see how much fertiliser is left in the spreader 4 39 FERTILISER DISTRIBUTOR BREDAL TEEJET 5000 OPERATORS MANUAL CLOSING THE GATE This key is used to close the gate on the Bredal spreader i e driving on the road This function mus
106. then weighing to ON otherwise set this to OFF WEIGHING ON If this function is required then the weighing system must be calibrated this is done as follows leefet 4 43 FERTILISER DISTRIBUTOR BREDAL TEEJET 5000 OPERATORS MANUAL 1 Press the CALIB CALC key and the picture to the left is displayed 2 With an empty spreader press the TARRING key to zero set the weigh cells 3 Fill the spreader with an exact known amount The weight should be as large as possible but must be minimum 50 of the spreaders capacity Using the arrow keys move the cursor to CALIB WEIGHT and encode the amount filled with the numerical keypad 4 Press the flashing LOAD FIG key The system has now been calibrated The calculated figure is displayed at the top of the screen note this figure if the system is to be used with other weigh cells in the future NOTE The weigh cell calibration should be checked at regular intervals DISTRIBUTOR WIDTH The effective spreading width of the spreader Method 1 Press the DISTRIB WIDTH key and the picture to the left is displayed 2 Encode the effective spreading width using the numerical keypad STEP Encode the size of the steps for the STEP function This 96 value is the same for both and The maximum step size is 9996 4 44
107. then set the minimum limit to 1 DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY leefet 4 21 FERTILISER DISTRIBUTOR OTHER WITH REG TEEJET 5000 OPERATORS MANUAL 4 22 Fertiliser distributor Bogballe D DZ 8 EX INTRODUC TION ee 4 24 BOGBALLE FERTILISER DISTRIBU VOR 4 25 FERTILISER DISTRIBUTOR OPERATION 4 26 FERTILISER DISTRIBUTOR FUNGCT IONG rure irren rtc 4 26 START AND STOP SPREADING 4 27 BOUM SEG TION ON OFF 4 27 FERTILISER DISTRIBUTOR ENCODE 4 28 DOSERA are ere ee ere ee ee 4 28 CALIBRA TION T 4 29 ACTUATOR CAEIBRAT ION iniu 4 30 ici m 4 31 c m 4 31 DISTRIBU TOR WID TH 4 31 STEP E 4 31 FORWARD SPEED 4 32 Lal dC 4 32 4 32 WHEEL SPREADER
108. then this amount must be added to the amount filled thus Amount left in hopper filled amount Kg left KG LEFT can be set as an alarm HA LEFT Encode the size of the field to be spread here END TIME is calculated from this encodement METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor SENSOR WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor 4 99 FERTILISER DISTRIBUTOR RAUCH AERO TEEJET 5000 OPERATORS MANUAL PTO SENSOR The number of pulses per revolution of the PTO is encoded here WARNING ENCODE The following warnings can be set in this menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warning ON OFF and MAX MIN limits for wheel slip in KG LEFT Warning ON OFF and amount of kg min at which warning is wanted NB The encoded limits must exceed the limits encoded If a warning is required when an axle stops 0 RPM then set the minimum limit to 1 DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY 4 100 Fertiliser distributor Rauch Beta Delta Beta Axera M Beta PK1100 Alpha og MDS11 Delta D
109. through the many new possibilities the TeeJet 5000 provides Try to learn only 1 program i e the program relating to the implement to be used first As once you have learnt one program you have learnt them all Please don t be confused by the constantly changing pictures and text on the screen this will soon become second nature for you when operating the TeeJet 5000 Be selective avoid using too many functions to start with i e warnings These functions can always be selected when at a later date you feel more confident with the computer A TeeJet 5000 is not just a TeeJet 5000 but a product that is under constant development The computer version is displayed on the screen each time the computer is started Please use this reference should you need to contact your local dealer You are always welcome to contact your local dealer with questions or suggestions for the TeeJet 5000 plus the wide range of implement equipment available that is always under development in close co operation with leading machinery manufacturers This manual is written so that many of the functions that are available in all of the programs are described in chapters 1 and 2 e g forward speed calibration and the task function TeeJet 5000 version 4 16 We endeavoured to deliver fault free product To ensure optimal use of the equipment we ask that great attention be paid when reading the manual Please c
110. wanted OFF PTO Warning ON OFF MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warning ON OFF and MAX MIN limits for wheel slip in RPM 1 Warning ON OFF and MAX MIN limits for PTO speed KG LEFT Warning ON OFF and amount of kg min at which warning is wanted NB The encoded limits must exceed the limits encoded If a warning is required when an axle stops 0 RPM then set the minimum limit to 1 DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY OFFSET Pressing the HOLD key for approx 5 seconds before accepting the selected fertiliser distributor type allows you to encode an OFFSET value This OFFSET value is used to alter the applied amount in comparison to the calibrated amount Example After calibration it is shown when spreading that the spread amount varies in comparison to the calibration This problem occurs because the spinner discs suck fertiliser out of the hopper The application rate is encoded to 200 kg ha but after spreading 10 ha 2100 kg has been spread this difference of 100 kg is equal to 5 Setting the OFFSET value the calibration so that the spread amount is the same as the calibrated application rate In the above example the OFFSET value should be changed to 0 95 If the amount spread was 5 low the above example then the OFFSET value should be altered to 1 05
111. weighing a few loads to establish the effective TANK VOLUME FILLED VOLUME Encode the amount filled into the tank if FX the tank is only filled half way up Needs only to be encoded if the amount filled differs from the TANK VOLUME Remember Encode the amount filled before leaving encode HA LEFT Encode the size of the field to be spread here END TIME is calculated from this encodement FLOW FIGURE FLOW ON OFF Without flowmeter Set flow to OFF and the application rate is calculated after each load With flowmeter Set to ON and the flowmeter must be calibrated CALIBRATION NOTE Encode a start value of 500 Automatic calibration 1 Fill the slurry spreader to the top so that you know the exact amount 2 Encode the amount in FILLED VOLUME 3 Empty the tank completely but be sure to stop emptying as soon as the tank is empty as air going through the flowmeter can cause false readings 4 Encode 0 00 using the numerical keypad under TANK REM VOL 5 Press the flashing CALC FLOW key 6 The flow figure is calculated NOTE Greater accuracy can be achieved by weighing the loads A new flow figure is calculated each time CALC FLOW is pressed 7 48 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER ZUNHAMMER Manual calibration The flow figure can also be calculated manually as follows
112. within reach and sight of the driver during operation preferably to the right of the operator S 80 60 6 5 gt Ensure that the cable from the mounting bracket is as protected as possible when routing the cable 12 6 Teglet 5000 OPERATORS MANUAL FITTING THE JUNCTION BOX FITTING INSTRUCTIONS Fit the junction box under the instrument panel or on the underside of the cab When fitting the junction box outside the cab moisture must be taken into consideration The cable holes in the rubber caps should not be cut any larger than the cable and the cable should be long enough to allow for DRIP OFF POINTS before entering the junction box see diagram below SiS DRIPPING 1808 0100 Teglet 12 7 FITTING INSTRUCTIONS TEEJET 5000 OPERATORS MANUAL POWER SUPPLY The TeeJet 5000 system can with additions have a power demand of 4 Amps when working with control equipment electromagnetic clutches motors etc We recommend in such circumstances that the power supply is drawn directly from the battery but as the computer must switch off when the ignition is switched off draw the power through a relay controlled via the ignition see diagram TO MONITOR 12V i BATTERY AUTO FU
113. 0 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BOGBALLE KG LEFT The amount filled into the spreader must be encoded here to be able to see how much fertiliser is left in the hopper NOTE If there is some fertiliser left in the hopper before refilling then this amount must be added to the amount filled thus Amount left in hopper filled amount Kg left HA LEFT Encode the size of the field to be spread here END TIME is calculated from this encodement DISTRIBUTOR WIDTH The effective spreading width of the spreader Method 1 Press the DISTRIB WIDTH key and the picture to the left is displayed 2 Encode the effective spreading width using the numerical keypad STEP Encode the size of the steps for the STEP function This value is the same for both and The maximum step size is 99 leefet 4 31 FERTILISER DISTRIBUTOR BOGBALLE TEEJET 5000 OPERATORS MANUAL FORWARD SPEED CALIBRATION The TeeJet 5000 V 4 fertiliser distributor program Begballe gives the option of choosing between 3 different speed sensors Wheel tractor Wheel spreader Radar WHEEL TRACTOR The speed signal can come from a sensor fitted in the gear box or on a drive shaft or from a sensor fitted on a wheel depending on the make and model of the tractor used for fertiliser spreading RADAR If the tractor is fitted with radar then sele
114. 0 FERTILISER DISTRIBUTOR ENCODE TEEREEEEERRERRRERER DE 4 40 er qmd En 4 41 pam 4 43 4 43 ctm 4 43 DISTRIBU TOR WIDTH siii CECI 4 44 STEP 4 44 FORWARD SPEED SENSOR ESEESE 4 45 4 45 METRE SWITO 4 45 ue desse nelm 4 45 REVS SENSOR aa eee eee eee ene rere errr te 4 46 remanent tere rarer ter earner ee tT 4 46 DATE SGEOUN atten earner ever edat eee 4 46 Tejet 4 35 FERTILISER DISTRIBUTOR BREDAL TEEJET 5000 OPERATORS MANUAL INTRODUCTION The TeeJet 5000 BREDAL fertiliser distributor program Maintain the correct application rate regardless of forward speed plus the ability to alter the application rate in steps depending on the crop s requirement The TeeJet 5000 controls the application rate using an actuator to control the gate position on the fertiliser spreader constant adjustment to maintain the application rate Visible and audible warnings given for incorrect rates forward speed PTO KG left etc NOTE The comput
115. 0 OPERATORS MANUAL SETTING HYPER TERMINAL UP Click on the Hyper Terminal icon You can find the program icons in various places depending on the way that Windows95 has been set up Refer to the Windows95 98 operator manuals for further instruction Double click on the icon C PROGRA 1 ACCESS 1 HYP File Edit View Help A AT amp T MCI CompuServe a hypertrm dll ns hticons dll 4 1 object s selected Figure 3 Screen shot of Hyper Terminal Select a name and an icon for this connection Then choose the correct serial port for your PC Connection Description New Connection Enter name and choose an icon for the connection Name 5000 Figure 4 New Connection 2 12 Teejet 5000 OPERATORS MANUAL GENERAL FUNCTIONS IPhone Number Choose the Com Port that corresponds to the serial port being used Figure 5 Connect Using HyperTerminal Change the Port settings to the following COM2 Properties Appi Figure 6 Serial port properties HyperTerminal When you have finished set up choose Save As in the file menu A dialogue box is shown where it is possible to save the set up to a file The program suggests ht as the file type Next time you wish to transfer
116. 000 OPERATORS MANUAL FITTING INSTRUCTIONS Motor control and boom compensation can not be connected through the breakaway plug but should be connected to the system A plug Complete kits are available for a number of sprayers please contact TeeJet AGRO Implement sensor kit TeeJet no 930 982 Speed sensor kit TeeJet no 930 982 Flowmeter 20 200 l min TeeJet no 902 986 Break away plug male TeeJet no 178 601 Fitting kits for flowmeters should be ordered separately to fit the sprayer in question The following shows a tailor made kit for automatic application control and boom compensation Hardi EC manifold Teglet 12 15 FITTING INSTRUCTIONS TEEJET 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR MONITORING FERTILISER DISTRIBUTOR SENSOR WIRE COLOUR PIN NUMBER BLACK RPM SENSOR 2 BLUE 5 WEIGHING MODULE BLACK ___ SPEED SENSOR BLUE 4 j L BROWN 5 IMPLEMENTSENSOR BLUE 5 Using the standard kit for fertiliser distributors from TeeJet Technologies gives a better and neater installation which is prepared for additions see the diagram below 1 Wheel sensor implement sensor 930 982 2 Shaft speed sensor kit 930 983 12 16 5000 OPERATORS MANUAL FITTING INSTRUCTIONS FITTING INSTRUCTIONS TEEJET 5000 OPERATORS MANUAL APPLICATION CONTROL The following
117. 10 11 12 GENERAL USE GENERAL FUNCTIONS SPRAYER FERTILISER DISTRIBUTOR DRILL BALER SLURRY SPREADER OTHER IMPLEMENTS DGPS FUNCTIONS OVERVIEW FITTING INSTRUCTIONS Contents USE i ie ee ere ti te E M GER 1 1 GENERAL FUNCTION S e cat ctt e o cac en eie A 2 1 mcdio LA LAU ALME 3 1 FERTILISER DISTRIBUTOR OTHER TYPE itio eei nena etu the ti nene 4 1 FERTILISER DISTRIBUTOR OTHER TYPE WITH 4 13 FERTILISER DISTRIBUTOR BOGBALLE D E DZ amp 4 23 FERTILISER DISTRIBUTOR BREDAL B2 B4 amp 4 35 FERTILISER DISTRIBUTOR BREDAL HYDR 4 47 FERTILISER DISTRIBUTOR BREDAL HYDR 4 61 FERTILISER DISTRIBUTOR BREDAL K RAMP 4 75 FERTILISER DISTRIBUTOR RAUCH AERO benc eene 4 89 FERTILISER DISTRIBUTOR RAUCH 4 101 FERTILISER DISTRIBUTOR RAUCH 4 113 FERTILISER DISTRIBUTOR iint re hi rib i 4 125 SEED DRILL OTHER TYPE ttt c A e c du dedu 5 1 SEED DRIEE NORBSTEING iine teer
118. 2 RPM SENSORS If the spreader is not fitted with either weigh cells or pulse generators then the TeeJet 5000 can display the shaft speed for another axle instead of KG metering RPM 1 Shaft speed for axle no 1 RPM 2 Shaft speed for axle no 2 4 6 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR OTHER TYPE BOOM SECTION ON OFF The picture to the left shows a spreader with 2 sections where one is open and one is closed The total number of sections is set under encode When the area override sensor is activated not I counting area I is displayed and all sections will disappear FERTILISER DISTRIBUTOR ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements gt gt 00 OA d KG LEFT This function is only available if PULSE WEIGHING has been selected The amount filled into the spreader must be encoded here to be able to see how much
119. 25 EM E ES Gigs _ amp Q nmna 5 6 5000 OPERATORS MANUAL SEED DRILL OTHER TYPE METHOD A EVEN A rhythm of 4 is encoded in this example A single S clutch is fitted on the left hand side of the seed 9 drill Tramlines are made A CY bout numbers 2 and 3 split when a rhythm of 4 is encoded n QJ NJ N Note where the first4 P bouts around the whole I field the bouts should be counted A and where bouts should not j be counted all other corners After each trip around field the machine is turned around and is driven in the opposite direction Bout counting can be DX PG 7 controlled by using either C the HOLD key or by using the TRACK N 7 keys C N OR 9209 02 5 7 SEED DRILL OTHER TEEJET 5000 OPERATORS MANUAL METHOD B UNEVEN A rhythm of 3 is encoded in this example and there are 2 clutches fitted in the middle of the seed drill
120. 4 Pe MT entre tenner 7 24 WHEEL SLURRY SPREADER 7 24 IMPLEMENT 7 24 t tm 7 25 WORK HOUR ec ede 7 25 sq 7 25 WARNING ENCODE mE 7 26 Br meds Sane 7 26 Teglet 7 15 SLURRY SPREADER OTHER TYPE HYDR TEEJET 5000 OPERATORS MANUAL INTRODUCTION The TeeJet 5000 used to control the amount spread using hydraulic control of a ball valve Maintain the correct application rate regardless of forward speed plus the ability to alter the application rate in steps depending on the crop s requirement The TeeJet 5000 controls the application rate using a proportional valve that adjusts the amount of oil to a hydraulic cylinder which in turn adjusts the position of a valve Visible and audible warnings given for incorrect rates forward speed PTO tons m3 left etc NOTE The computer must be calibrated with the spreader to ensure correct operation 7 16 Teglet TEEJET 5000 OPERATORS MANUAL SLURRY SPREADER OTHER TYPE HYDR SLURRY SPREADER HYDRAULIC CONTROL Select slurry spreader from the main menu as follows 1 Using the arrow keys move the cursor over SLUR
121. 4 Press OK when it appears on the display the calibration procedure is finished 4 84 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL RAMP WEIGHING EIGHING If the spreader is equipped with weigh cells then set weighing to ON otherwise set this to OFF WEIGHING ON If this function is required then the weighing system must be calibrated this is done as follows 1 Press the CALIB CALC key and the picture to the left is displayed 2 With an empty spreader press the TARRING key to zero set the weigh cells 3 Fill the spreader with an exact known amount The weight should be as large as possible but must be minimum 50 of the spreaders capacity Using the arrow keys move the cursor to CALIB WEIGHT and encode the amount filled with the numerical keypad 4 Press the flashing CALC LOAD FIG key The system has now been calibrated The calculated figure is displayed at the top of the screen note this figure if the system is to be used with other weigh cells in the future NOTE The weigh cell calibration should be checked at regular intervals 4 85 FERTILISER DISTRIBUTOR BREDAL RAMP TEEJET 5000 OPERATORS MANUAL DISTRIBUTOR WIDTH The effective spreading width of the spreader Method 1 Press the DISTRIB WIDTH key and the picture t
122. Area counter Worked area since the last reset NOTE Total area counter is found DATA DELETE KG Total KG used calculated from forward speed and gate position This function presupposes correct calibration NOTE Total KG counter is found in KG REST Total KG remaining in the hopper the amount must be encoded before start Pressing the NEXT PAGE key displays the next functions AUTO MAN Pressing this key changes between automatic and manual application control During manual operation flashes at the bottom of the display Higher application rate Lower application rate KG HA The present application rate 4 94 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH AERO Each press of this key increases the speed of the feed rollers by 1 RPM If the key is held down then the speed of the feed rollers will increase at a suitable speed The present application rate can be seen at the same time by pressing KG HA Each press of this key decreases the speed of the feed rollers by 1 RPM If the key is held down then the speed of the feed rollers will decrease at a suitable speed The present application rate can be seen at the same time by pressing KG HA The present application rate calculated from forward speed working width plus the present speed of the f
123. DOSE RATE is selected Some spreaders are fitted with gt gear It is possible to alter the calculated gear by pressing the GEAR key A new calculation must take place if the calculated gear has been altered If the calculated scale is greater than 300 then GEAR must be altered again Please refer to the documentation supplied with the spreader for more information 4 82 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL RAMP The required application rate and spreader setup is encoded thus Encode the required application rate with the numerical keypad under DOSE TON HA The SPECIFIC GRAVITY is found using the specific gravity tester supplied by BREDAL Pressing CALC CALIB Calculates the correct SCALE and GEAR This menu cannot be left until CALC CALIB has been pressed The required DOSE RATE along with the specific gravity and the distributor width gives The scale setting The correct gear on the spreader NOTE The settings must be re calculated under DOSE RATE each time the working width of the spreader has been altered TON LEFT The amount filled into the spreader must be encoded here to be able to see how much lime is left in the hopper NOTE If there is some lime left in the hopper before refilling then this amount must be added to the amount filled thus Amount left in hopper filled a
124. DRILL FUNG BONS E ERE tex ea ERR 5 34 SELECTING THE TRACK E Exp E RERE RU 5 36 METHOD A c 5 36 METHOD fm ECC 5 38 METHOD C 5 40 METHOD Wc E I 5 42 5 44 METHOD EEUU 5 46 METHOD CER 5 48 METHOD FI PH 5 50 Susa 5 52 DOSE 5 52 es ceerceecaseyececener ceecskecsseceterieecceerevensiee 5 53 c 5 54 5 54 HALE E DRM 5 54 ei pp 5 54 TRACK islam c eae 5 55 ROW NO Rp 5 55 NUMBER OF RETURNS E 5 55 ROWS IN TRACK mm Cc 5 55 FORWARD SPEED SENSOR 5 55 MANUAL START et 3 204 059 E EEE EEE 5 55 MEIRE SWITCH e nT 5 55
125. EN Example of Method A Uneven In this example the encoded rhythm is 3 Two clutches or 2x2 solenoid shutters are fitted in the middle of the drill Tramlines are made in bout number 2 when a rhythm track number of 3 is encoded EY A41 Note where in the first 3 bouts around the field the present bout should be counted T and the bout should not be 11 counted After each trip around the field the machine drives in the opposite direction x ra Bout counting can be controlled by using either the HOLD key or by using the TRACK keys leefet 5 37 SEED DRILL LEMKEN TEEJET 5000 OPERATORS MANUAL METHOD B This method is the most traditional and the most used method Tramlines are made when the bout number is the same as the track number Example of method Even The tramline cannot be split over 2 bouts in this example with a rhythm of 4 encoded The first bout can only be AA sown with one half of the drill open Once this is done the tramlines can made with either 2x2 solenoid shutters or 2 clutches fitted to the middle i of the drill Tramlines are made when present numbe
126. ERSATZTEILE SPARE PARTS PIECES NR DETACHEES 8 1 1 865 171 Blaendplade Blendplatte Cover plate Couvercle 865 170 Blaendplade Blendplatte Cover plate Couvercle 98 025 Kabel m stik Kabel mit Stecker Cable with plug Cable a fiches 78 507 Las f stik Verschlup f r Lock for plug Blocage pour fiche Stecker Skrue 2 9 x 9 5 Vis 2 9 x 9 5 Motrikbeskytter Protecteur d crou 8 30 005 Skive M5 Scheibe M5 Washer M5 Rondelle M5 811 845 Skrue M8 x 45 Schraube M8 45 Screw M8 x 45 Vis M8 x 45 861 110 Metrikbeskytter Mutterschoner Nut protector Protecteur d crou 58 800 Metrik 8 m l s Mutter M8 mit Nut with lock Ecrou bloquant M8 verschluB 8 844 205 Trapezmatrik Trapezmutter Ecrou trap zoidale 866 012 Plastboks 900 499 Samleprint Str mkabel C ble d alimentation 178 600 Anh ngerstik Ger tekupplungs Trailer plug stecker 11 535 Skrue M5 x 35 Schraube M5 x 35 Screw M5 x 35 Vis M5 x 35 8 900 982 2 ledet f ler 2 adr Fuhler 2 core sensor Capteur a 2 conducteurs 827 412 Skrue M4 x 16 Schraube M4 x 16 Screw M4 x 16 Vis M4 x 16 o 865 165 Statteskinne St tzschiene Supporting plate Support 830 931 Skive M8 Scheibe M8 Washer M8 Rondelle M8 7 10 11 12 13 14 15 16 17 18 19 20 21 22 23 2 2 2 2 2 5 6 7 8 9 30 31 2 Teglet 12 5 FITTING INSTRUCTIONS TEEJET 5000 OPERATORS MANUAL FITTING THE COMPUTER Fit the computer
127. ERTILISER DISTRIBUTOR OTHER TEEJET 5000 OPERATORS MANUAL TARRING 1 Press TARRING with an empty fertiliser distributor the displayed KG will change to 0 2 Fill the spreader and the weight will be displayed Using weighing There are 2 possibilities Start spreading with the weight displayed and at each weighing the amount left in the spreader can be seen Each time TARRING is pressed the displayed KG will be 0 It is now possible to see how much has been used negative weighing It is not possible to see how much fertiliser is left in the spreader NOTE The actual weight is stored in the memory when DRIVE START is pressed This value is used together with area measurement to calculate KG HA The accuracy of this calculation depends on the amount of fertiliser spread since the last calculation the larger the amount the better the accuracy 4 4 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR OTHER TYPE Stop driving and stop the spreader When you are ready to start spreading press DRIVE START and start spreading until 10 of the hopper size has been spread NOTE If you start spreading without pressing DRIVE START a warning will be displayed You must now stop spreading and wait 8 seconds press DRIVE START again CALC KG HA Pres
128. EXT PAGE key displays the next functions 4 92 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH AERO HA Area KG Consumption in KG KG LEFT How many KG are left in the hopper at present HA Area counter Worked area since the last reset NOTE Total area counter is found DATA DELETE KG Total KG used calculated from forward speed and gate position This function presupposes correct calibration NOTE Total KG counter is found in DATA DELETE KG REST Total KG remaining in the hopper the amount must be encoded before start Pressing the NEXT PAGE key displays the next functions HOPPER CONT Amount remaining in the hopper AUTO MAN Select manual or automatic application control HOPPER CONT The calculated amount remaining in the hopper the amount filled into the hopper must be encoded before starting AUTO MAN Pressing this key changes between automatic and manual application control During manual operation MAN flashes at the bottom of the display Pressing the NEXT PAGE key displays the first functions 4 93 FERTILISER DISTRIBUTOR RAUCH AERO TEEJET 5000 OPERATORS MANUAL 2 MANUAL APPLICATION CONTROL HA Area KG Consumption in KG KG LEFT How many KG are left in the hopper at present HA
129. Fill the slurry spreader to the top so that you know the exact amount Reset the amount counter DATA DELETE Empty the tank completely Read the amount DATA DELETE Place the value in the following formula g Be O N c Old flow figure x the amount spread NEW FLOW FIGURE The amount read in Data delete TeeJet 5000 6 Encode this new flow figure using the numerical keypad BOOM WIDTH The working width of the spreader If the system is fitted with control valves for each section then the individual section width must be encoded here left boom section 1 If the spreader does not have individual sections then encode the whole spreader width as section 1 all other sections must be encoded as 0 UNIFORM PRESSURE If the 5 distribution head is fitted with uniform pressure valves return to tank or not ON YES OFF NO Teglet 7 49 SLURRY SPREADER ZUNHAMMER TEEJET 5000 OPERATORS MANUAL FORWARD SPEED SENSOR The TeeJet 5000 V 4 slurry spreader program gives the option of choosing between 3 different speed sensors Wheel tractor Wheel spreader Radar WHEEL TRACTOR The speed signal can come from a sensor fitted in the gear box or on a drive shaft or from a sensor fitted on a wheel depending on the make and model of the tractor used for slurry spreading RADAR If the tractor is fitted with radar then select RADAR and forward speed will be measured from the radar
130. HOUR ON OFF 7 11 REVS SENSOR ieee ee ee ee ee 7 11 WARNING ENCODE iii oon rust Een ORE ern err rr at re 7 12 Bgm el wi E 7 12 Teefet 7 1 SLURRY SPREADER OTHER TEEJET 5000 OPERATORS MANUAL SLURRY SPREADER Select slurry spreader from the main menu as follows 1 Using the arrow keys move the cursor over SLURRY SPREADER Press SELECT 2 Main menu select slurry spreader 3 Accept the selected type or choose another type 4 Select type 5 It is now possible to choose between the displayed types 6 Select the slurry spreader type 7 Accept It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 7 2 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER OTHER SLURR
131. L FUNCTIONS This chapter deals with the functions that can always be chosen no matter which implement is used The functions related to a certain implement will be dealt with in the chapter on the implement in question The encoded values which are conditional on several of the functions will be dealt with under the respective implements as each implement has specially encoded values FUNCTION KEYS Using the 4 FUNCTION KEYS and the RETURN KEY allows you to page through all the functions of the computer in a clear and systematic manner The actual function of each of the 4 function keys is shown on the display to the left of the key Pressing one of the keys may change all of the keys to a new function see the examples below BASIC MENU The display shown is the first page of the menu system From this screen the first selection is made i e which of the 6 implement programmes you want to use Moving the cursor the dark area by using the arrow keys and then pressing the SELECT key selects the required implement 2 2 5000 OPERATORS MANUAL GENERAL FUNCTIONS IMPORTANT IMPORTANT IMPORTANT During operation drivin
132. MANUAL METHOD C This method is used with a 6 metre seed drill making 15 metre tramlines The track number is set to 10 see track number page 5 55 Example of method C Right The seed drill is fitted with 2x2 magnetic valves on the right hand side of the machine and 2x2 magnetic valves fitted on the left hand side of the machine Drilling is started on the right hand side of the field as shown on the diagram One half of the drill must be closed for the first bout Thereafter the track number should be changed to 9 10 and tramlines are made when the actual track number is 2 4 7 and 9 Note where the bouts should be counted A and where bouts should not be counted all other corners in the first 3 bouts around the whole field Bout counting can be controlled by using either the HOLD key or by using the keys _ ODA OAT m c 5 40 5000 OPERATORS MANUAL SEED DRILL LEMKEN Example of method C Left The seed drill is fitted with 2x2 magnetic valves on the right hand side of the machine and 2x2 magnetic valves fitted on the left hand side of the machine Drilling is started on the left hand side of the field as shown on the diagram One half of the drill must be closed for t
133. Min 1 5 kph Max 3 0 kph 5 58 5000 OPERATORS MANUAL SEED DRILL LEMKEN 5 59 SEED DRILL LEMKEN TEEJET 5000 OPERATORS MANUAL 5 60 Seed drill Simba SEED DRILL SIMBA ip 5 62 SEED DRILL OPERATION APEE en ER EH RARE 5 63 HOLD 4 d D 5 64 TRAMLINE INDICAT TOR 5 64 FORWARD SPEED 5 64 TRAMLINE GONTISOL on tup 5 65 PE TT Pte ac ceca 5 65 25 5 65 METHOD A UNEVEN e 5 66 METHOD AEVEN ARAA ARNA gn aes 5 67 NE TS Ns sas Sots cd sche ss 5 68 METHOD BEVEN qt a eae eee 5 69 SEED DRILL ENCODEMNBNUT REED 5 70 FAN NUMBER SELEG a 5 70 KG LEF remm 5 71 HA 5 71 TRACK NUMBER CDL EE 5 71 SOW FIGUR m 5 71 T 5 72 ROWS INF TRACK e 5 72 SOW 5 72 FORWARD SPEED SE ING
134. NG THE TRACK RHYTHM esce s 5 20 SF ed S eee rns eee eee ere eee ee ey re 5 20 METHOD A m m 5 22 SEED DRILL ENCODEMENT einen eet M ut 5 24 DOSE RATE enimse ai 5 24 CALIBRA MON D 5 25 ee G 5 26 KOLERI umm 5 26 HALEF idee anA 5 26 OW RIPE 5 26 TRACK NUMBER DES 5 27 5 27 pie ca Eg nie 5 27 FORWARD SPEED SENSQONS iunctis 5 27 IMPLEMENT SENSOR uS uersa ce ete aga wee cdc we cee ea 5 27 MANUAL START erp 5 27 METRE adaa 5 27 WORK HOUR ON OFF 5 28 REVS SENSOR T 5 28 WARNINGS 5 29 5 29 WARN WHEEL Q 5 30 2 5 30 DATES A 5 30 5 15 SEED DRILL
135. NPUT OUTPUT BALER TEST INPUT BALER TRAIL 1 Signal from the bale counter TRAIL 2 Signal from the RPM 3 sensor or bale weight if fitted TRAIL 4 Signal from RPM 2 sensor TRAIL 7 Signal from RPM 1 sensor TRAIL 8 Not used TRAIL 15 Not used TRAIL 16 Not used BOM 1 12 Not used TEST OUTPUT OUT 1 Not used OUT 2 Not used OUT 3 Not used OUT 4 Not used POT 1 2 Not used Teglet 2 29 GENERAL FUNCTIONS TEEJET 5000 OPERATORS MANUAL TEST INPUT OUTPUT SLURRY SPREADER TEST INPUT OTHER TYPE HYDRAULIC TRAIL 1 Signal from RPM 1 sensor i e Signal from RPM sensor fitted to distributor or macerator the distributor TRAIL 2 Signal from the slurry flowmeter Signal from flowmeter or signal from RPM sensor fitted to a positive displacement pump TRAIL 4 Speed signal from sensor fitted Speed sensor fitted on the slurry on the slurry spreader spreader TRAIL 7 Area override on off signal from Area override on off signal from sensor fitted on the slurry sensor fitted on the slurry spreader spreader TRAIL 8 Not used Signal from the RPM sensor fitted to the pump TRAIL 15 Not used Not used TRAIL 16 Not used Not used 1 12 Signal from boom section Signal from boom section switches via system B plug if switches via system B plug if used used TEST OUTPUT OUT 1
136. O 5 72 Mes bas 5 72 WHEEL tcc 5 72 RADAR m 5 72 IMPLEMENT A 5 72 METRE supe D 5 73 WORK HOUR ON OFF 5 73 REVS SENSOR ee ms en en ea 5 73 WARNING ENG OD Bie ei eee eee ee 5 74 DATE OCI 5 74 leefet 5 61 SEED DRILL SIMBA SEED DRILL SIMBA TEEJET 5000 OPERATORS MANUAL Select drill from the main menu 1 Move the cursor using the arrow keys to DRILL when this is done press the SELECT key 2 Main menu Drill 3 ACCEPT the selected type or choose another type 4 Select type 5 It is now possible to choose between the displayed types 6 Select the drill type 7 ACCEPT NOTE NORDSTEN ELECTR Is only for NORDSTEN with electronic gearboxes It is now possib
137. P Encode the size of the steps for the STEP function This 96 value is the same for both and The maximum step size is 9996 4 71 FERTILISER DISTRIBUTOR BREDAL HYDR K TEEJET 5000 OPERATORS MANUAL FORWARD SPEED SENSOR A speed sensor is fitted to the spreader this sensor gives the correct number of pulses for controlling the application rate and this sensor should be selected WHEEL TRACTOR AND RADAR If forward speed measurement is not required from the sensor mounted on the spreader WHEEL TRACTOR or RADAR can be selected Please refer to chapter 2 for speed sensor calibration METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor SENSOR WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor REVS SENSOR Encode the number of pulses per revolution for the individual sensors PTO SENSOR If the TeeJet PTO sensor kit is used 932 983 encode 1 RPM1SENSOR Bredal kit is supplied with sensor fitted for disc speed the number of pulses per revolution should be set to 1 4 72 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL HYDR WARNING ENCODE The following warnings can be set in this men
138. PERATION FORWARD SPEED The primary function under fertiliser distributor is forward speed Forward speed is displayed in KPH with 1 decimal Forward speed is calculated from the signal from the speed sensor selected in encode wheel tractor wheel sprayer or radar AREA MEASUREMENT The worked area is displayed in Ha Area is displayed with 2 decimals from 0 to 99 99 ha And thereafter with 1 decimal from 100 to 999 0 ha NOTE total counter for area can also be found in DATA DELETE LIME SPREADER FUNCTIONS TON HA RPM 1 Application rate in TON HA TON Lime consumption in tons TON LEFT Tons remaining in the hopper the amount must be encoded before starting Step dosage increase DOSE RATE NORMAL Encoding the required application rate or return to normal after using the step key 4 78 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL K RAMP XX Percentile increase of the encoded application rate The size of the steps is altered in encode XX Percentile reduction of the encoded application rate The size of the steps is altered in encode NORMAL Only displayed if the step feature has been used Normal application rate Regardless of how many steps the application rate has been
139. PERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 4 90 Teefet 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH AERO FERTILISER DISTRIBUTOR OPERATION FORWARD SPEED The primary function under fertiliser distributor is forward speed Forward speed is displayed in KPH with 1 decimal Forward speed is calculated from the signal from the speed sensor selected in encode wheel tractor wheel sprayer or radar SPREADER SECTION INDICATION The picture to the left shows a 4 section spreader with both sections open The number of sections can be changed in ENCODE The figure to the right indicates which calibration is being used RPM FOR FEED ROLLERS AND REGULATION The speed of the feed rollers is displayed this speed expresses the application rate An arrow to the left of the screen shows whether the feed roller speed is increasing or decreasing When the area override sensor is activated not 1 counting area I is displayed and all sections will disappear FERTILISER SPREADER FUNCTIONS There are 2 different function sets in this menu The 0 5 displayed set depends whether automatic or manual application control has been selected The following describ
140. R 2 7 41 Slurry spreader Other type SLURRY SPREADER 7 2 SLURRY SPREADER OPERATION eh Phe EFFERRE FERE RERERP I ERR CERE ERE EEE 7 3 SLURRY SPREADER FUNCTIONS WITH FLOWMETER seeen 7 3 SLURRY SPREADER WITHOUT 111 7 5 SLURRY SPREABERIEBNOOLDE 7 1 DOSERA nt T T E coer E T S To TANK VOLUME ee eee errr ee ee ee eee re 78 RILLED Iv Bie Te 1 8 HA 7 8 ts FIGURE anan 7 8 BOOM 7 9 DRIVE FAC JOR sesigege 7 9 55 7 9 FORWARD SPEED SENSOR 7 10 WHEEL TRACTOR otc 7 10 RADAR cheese S 7 10 WHEEL SLURRY SPREADER a 7 10 IMEPEENENT SENSOR cece cece EC TEETE ATEARI TIERE 7 10 METRE SWITCH EE 7 10 SYSTEM BPLUG WC 7 11 WORK
141. R DISTRIBUTOR RSS 4 2 FERTILISER DISTRIBUTOR OPERATION OTHER TYPE 4 3 FERTILISER DISTRIBUTOR FUNC 4 3 1 WEIGHING DIRECT WEIGHING WITH WEIGH 5 4 3 2 PULSE WEIGHING ae ne ee ee 4 6 33 2 RPM SENSORS cena entitle eee 4 6 BOOM SEG TION ON OFF Ara Eiai ar EnF secede ce ERr EEEE 4 7 FERTILISER DISTRIBUTOR ENCODE diet D NU Le 4 7 m 4 8 tiu tapete C 4 8 WEIGHING me 4 8 PULSE rg 4 8 RPM 2 4 9 aA 4 10 FORWARD SPEED SENS 4 10 WHEEL TRACTOR ere ee ee ee 4 10 WEBEL SPREADER pq EE iee 4 10 RADAR e e Oa 4 10 IMPLEMENT SENSOR fe 4 10 METRE SWITCH A Odd 4 10 SYSTEM B PESO i eoa 4 11 WORK HOUR ON OFF cipes SE eEEREFREEE
142. RATION 6 6 3 BALER FUNGTIONGS tote aote pn pru dui pls ai 6 3 SWITCHING ALL WARNINGS OFF te en eee Eee Cte eee ee tte nont 6 4 BALER ENG ODE edid ended ut eu 6 5 WEIGHING REMS taia etate tet 6 5 FORWARD SPEED SENSOR zen dicte tendit me 6 6 REVS SENSOR fate 6 7 WARNING S sete eren inb ctn et rb es 6 7 DATE CLOCK 6 7 BALER TEEJET 5000 OPERATORS MANUAL BALER Select baler from the main menu as follows Move the cursor using the arrow keys to when this is done press SELECT The following is displayed It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 6 2 Teefet
143. RH ERE eH FE EEEn AE 4 11 REVS SENSOR aei qq Ra dE 4 11 pre eel 4 12 DATE CLOCK qw 4 12 41 FERTILISER DISTRIBUTOR OTHER FERTILISER DISTRIBUTOR OA 0 gt m m TEEJET 5000 OPERATORS MANUAL Select fertiliser distributor from the main menu as follows 1 Move the cursor using the arrow keys to FERTIL DISTRIB Press the SELECT key 2 Main menu select fertiliser distributor 3 ACCEPT or SELECT TYPE 4 Select type 5 It is now possible to choose between the displayed types 6 Select fertiliser distributor type 7 Accept type It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of
144. RY SPREADER Press SELECT 2 Main menu select slurry spreader 3 Accept the selected type or choose another type 4 Select type 5 It is now possible to choose between the displayed types 6 Select the slurry spreader type 7 Accept The following is displayed It is now possible to choose between the displayed functions Each function will be described one by one in the following sections The task function is described in section 2 along with all of the other functions that are available in all sections 519 gt SLURRY SPREADER OTHER TYPE HYDR TEEJET 5000 OPERATORS MANUAL SLURRY SPREADER OPERATION APPLICATION RATE The primary function under slurry spreader hydraulic control is the application rate in TON MG per hectare This is calculated from the flow through the flowmeter and the area counter forward speed amp working width This means that to see a reading here the machine must be spreading and driving forward NB The flowmeter must be calibrated correctly the wheel circumference and the working width must be correct to ensure cor
145. SE a 86 FRAME CONTROL CURRENT 9215 1000 FROM IGNITION SWITCH Place the relay under the instrument panel or a similarly protected position The fuse should be positioned by the battery to ensure protection of the whole power cable 12 8 Teglet 5000 OPERATORS MANUAL FITTING INSTRUCTIONS FITTING THE FORWARD SPEED SENSOR The TeeJet 5000 system can receive speed signals from 3 different speed sensors a wheel sensor on the tractor a wheel sensor on the implement and radar Fitting the supplied wheel sensor is recommended on the rear right hand wheel of the tractor See the diagram below The distance between the magnet and the speed sensor should not exceed 5mm If the wheel circumference exceeds 250 cm then 2 magnets must be fitted When using automatic application control the wheel circumference should not exceed 100 cm if this is the case then more magnets should be added NOTE The magnets must be fitted with equal distance between each magnet otherwise the forward speed will spring The magnets can be fitted i e on the wheel bolts wA 0 2 e 61 2016 Teglet 12 9 FITTING INSTRUCTIONS TEEJET 5000 OPERATORS MANUAL It is preferable where it is possible to fit a speed sensor on the drive shaft of 4 wheel drive tractors This requires a different sensor than the one supplied as standard with the fitting kit This possibility is shown in the followin
146. Signal to open the reg Valve Signal to open the reg Valve The application rate must increase OUT 2 Signal to close the reg Valve Signal to close the reg Valve The application rate must decrease OUT 3 Not used Not used OUT 4 Not used Not used POT1 2 Not used Not used 2 30 Teglet 5000 OPERATORS MANUAL GENERAL FUNCTIONS TEST INPUT HORSCH ZUNHAMMER TRAIL 1 Not used Not used TRAIL 2 Signal from RPM sensor fitted Signal from RPM sensor fitted on the pump flow on the pump flow TRAIL 4 Signal from the wheel sensor Signal from the wheel sensor fitted on the slurry spreader fitted on the slurry spreader TRAIL 7 Signal from the implement Signal from the implement sensor fitted on the slurry sensor fitted on the slurry spreader spreader Note Always active TRAIL 8 Signal from the filling Signal from the filling mechanism mechanism TRAIL 15 Not used Not used TRAIL 16 Not used Not used BOM 1 12 Signal from the boom section BOOM 1 5 switches the system B plug Signal from the boom section boom compensation if this is switches via the system B plug used boom compensation if this is used BOOM 6 Alarm no slurry flow BOOM 7 Alarm High pressure 8 Alarm tank valve closed BOOM 9 Alarm fill pipe in BOOM 10 Full tank BOOM 11 Re circulation TEST OUTPUT OUT 1 Signal to open the pro
147. T 5000 OPERATORS MANUAL RAUCH BETA DELTA FERTILISER DISTRIBUTOR Select fertiliser distributor from the main menu as follows 1 Move the cursor using the arrow keys to FERTIL DISTRIB Press the SELECT key 2 Main menu select fertiliser distributor 3 ACCEPT or SELECT TYPE 4 Select type 5 It is now possible to choose between the displayed types 6 Select fertiliser distributor type 7 Accept type It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 4 102 Teefet 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH BETA DELTA FERTILISER DISTRIBUTOR OPERATION FORWARD SPEED The primary function under fertiliser distributor is f
148. T SENSOR The implement override sensor is used to stop and start area measurement and count the bouts driven It is possible to choose between LIFT and DRILL The override signal will normally come from a sensor fitted on the seed drill select DRILL MANUAL START Encode the number of seconds that the drill shaft will rotate for when MANUAL START is pressed max 20 seconds METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor SENSOR 5 27 SEED DRILL NORDSTEN TEEJET 5000 OPERATORS MANUAL WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor REVS SENSOR Encode the number of pulses the sensors fitted to the drill shaft give per revolution It is also possible to select between clutch monitoring and RPM monitoring monitoring fan speed on pneumatic machines PTO SENSOR Encode 1 if the TeeJet PTO sensor kit 932 983 is used DRILL SENSOR Encode the number of pulses per revolution for the drill shaft sensor normally 12 CLUTCH SENSOR Select whether it is a traditional seed drill clutch monitoring or whether it is a pneumatic seed drill fan monitoring Se
149. TANK VOLUME Encode the effective size of the tank here Check if possible by weighing a few loads to establish the effective TANK VOLUME FILLED VOLUME Encode the amount filled into the tank if FX the tank is only filled half way up Needs only to be encoded if the amount filled differs from the TANK VOLUME Remember Encode the amount filled before leaving encode HA LEFT Encode the size of the field to be spread here END TIME is calculated from this encodement FLOW FIGURE FLOW ON OFF Without flowmeter Set flow to OFF and the application rate is calculated after each load With flowmeter Set to ON and the flowmeter must be calibrated CALIBRATION NOTE Encode a start value of 500 Automatic calibration 1 Fill the slurry spreader to the top so that you know the exact amount 2 Encode the amount in FILLED VOLUME 3 Empty the tank completely but be sure to stop emptying as soon as the tank is empty as air going through the flowmeter can cause false readings 4 Encode 0 00 using the numerical keypad under TANK REM VOL 5 Press the flashing CALC FLOW key 6 The flow figure is calculated NOTE Greater accuracy can be achieved by weighing the loads A new flow figure is calculated each time CALC FLOW is pressed 7 34 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER HORSCH Manual ca
150. TEEJET 5000 OPERATORS MANUAL 4 60 Fertiliser distributor Bredal HYDR K INTRODUC ON 4 62 BREDAL S LIME SP EAD BR FEE FERE ERE NEESS 4 63 gt 2 acetone 4 64 LIME SPREADERSFUNGTIONS 4 64 SPREADER ON OFF i 4 66 LIME SPREADER ENCOBE norte 4 67 DOSE RA cet seer cee cece erases 4 67 eee cere errr 4 68 4 68 P VALVE CALIBRAT ION saat ship dt anc 4 69 AUTOMAN 4 70 DISTRIBUTOR WIDTH ciai reste ete ie ee are ee 4 70 WEIGHING mE 4 71 puse tiene C UT 4 71 S TEP T c H n 4 71 FORWARD SPEED SENG 4 72 WHEEL TRACTOR AND RADA positi 4 72 MEIRE SWI POH T ee ee cee ee eee re 4 72 WORK HOUR ON OFF cece 4 72
151. TEEJET 5000 OPERATORS MANUAL SYSTEM This function allows amongst other things the various inputs and outputs to be tested Pressing Select will display the following TEST INPUT Test of all inputs for each implement Sensors TEST OUTPUT Test of engine valve etc for each implement SYSTEM DATA The operator has no access to this function It contains important system data which must not be changed LANGUAGE Select the required language here DIESEL FLOW FIGURE Encode the flow figure for the optional diesel flowmeter It is necessary to encode a diesel flow figure as the diesel flow pulse differs from flowmeter to flowmeter 2 20 Teejet 5000 OPERATORS MANUAL GENERAL FUNCTIONS TEST INPUT OUTPUT Use test input if you suspect defect sensors There is a counter underneath each input description on the left hand side that registers the number of times that the input has been activated the counter is reset each time you leave the TEST INPUT menu The right hand side of the screen displays the status of the input HI LO Page through the screens by pressing NEXT total 4 screens RADAR Signal from the radar when driven slowly forward PTO Signal from
152. This type of sensor gives a very accurate speed reading on hard surfaces but a high crop and reflecting surfaces water gives an inaccurate reading Please refer to chapter 2 for speed sensor calibration FERTILISER CALIBRATION PROCEDURE The computer allows you to save up to 3 different calibrations e g different fertiliser types Each calibration represents the individual test plus 3 fixed but user defined application rates i e 150 kg ha 200 kg ha 250 kg ha A new calibration must be carried out each time 1 The first time the spreader is used 2 When the working width is changed 3 Change of fertiliser type A new calibration should take place when 1 If you suspect that the flow characteristics of the fertiliser have changed i e a new load 2 Change of weather temperature and moisture Even when the above factors have been taken into consideration fertiliser calibration should be checked at regular intervals leefet 4 109 FERTILISER DISTRIBUTOR RAUCH BETA DELTA TEEJET 5000 OPERATORS MANUAL FERTILISER CALIBRATION Prepare the spreader as follows before the fertiliser calibration procedure takes place 1 To ease the calibration procedure it is only necessary to calibrate one section of the spreader Using the switch box open this one section and shut all of the other sections The main on off switch should be set to off NOTE The calibration procedure can be done using both sect
153. Y SPREADER OPERATION APPLICATION RATE The primary function for slurry spreaders is application rate The application rate is displayed in TON M3 per hectare This rate is calculated from the flow through the flowmeter and area measurement forward speed and working width It is therefore necessary to both drive and spread to see this function NOTE To ensure correct operation the flowmeter must be calibrated the correct wheel circumference and the correct working width must be encoded FORWARD SPEED Forward speed is displayed in kilometres per hour with 1 decimal Forward speed is calculated using the sensor selected under encode wheel tractor wheel spreader or radar NOTE Remember to reset all counters in DATA DELETE before starting SLURRY SPREADER FUNCTIONS wiTH FLOWMETER The metered amount can be displayed in either TON or M3 cubic metres These options are selected in encode under DOSERATE TON M3 Slurry consumption in ton or M3 TON M3 REST amount left in the tank TON M3 MIN X Consumption per minute TON M3 The amount of slurry spread since starting This function works as a trip counter and can be deleted in DATA DELETE The total counter is also found here TON M3 REST The amount remaining in the tank This function presupposes encodement of the tank size TANK VOLUME in encode Every time
154. ad aM a 4 132 RADAR er 4 132 uk SS WS Sl bee eee 4 133 WORK HOUR ON OFF 4 133 METRE 4 133 SYSTEM B PEUG 4 133 WARNING ENCODE a 4 134 4 134 4 125 FERTILISER DISTRIBUTOR FERTILISER DISTRIBUTOR OA 0 gt m m TEEJET 5000 OPERATORS MANUAL Select fertiliser distributor from the main menu as follows 1 Move the cursor using the arrow keys to FERTIL DISTRIB Press the SELECT key 2 Main menu select fertiliser distributor 3 ACCEPT or SELECT TYPE 4 Select type 5 It is now possible to choose between the displayed types 6 Select fertiliser distribut
155. ad here END TIME is calculated from this encodement METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor IMPLEM SENSOR WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor 4 111 FERTILISER DISTRIBUTOR RAUCH BETA DELTA TEEJET 5000 OPERATORS MANUAL WARNING ENCODE The following warnings can be set in this menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warning ON OFF and MAX MIN limits for wheel slip in KG LEFT Warning ON OFF and amount of kg min at which warning is wanted NB The encoded limits must exceed the limits encoded If a warning is required when an axle stops 0 RPM then set the minimum limit to 1 DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY OFFSET Pressing the HOLD key for approx 5 seconds before accepting the selected fertiliser distributor type allows you to encode an OFFSET value This OFFSET value is used to alter the applied amount in comparison to the calibrated amount Example After calibration it is shown when spreading that the spread amount varies in comparison to the calibration This problem occurs
156. al after using the step key Percentile increase of the encoded application rate The size of the steps is altered in encode Percentile decrease of the encoded application rate The size of the steps is altered in encode This key has 2 functions DOSE RATE or NORMAL The primary function of the key is DOSE RATE the required application rate can be encoded by pressing this key If the application has been increased decreased using the step function then NORMAL appears and the key will return the application rate to normal Pressing NORMAL once will return the application rate to normal regardless of how much the application rate has been increased decreased 3 4 5000 OPERATORS MANUAL SPRAYER WORK PRESS The working pressure of the sprayer in BAR with 1 decimal optional pressure sensor must be fitted WORK PRESS TARRING TARRING Zero setting the pressure sensor Pressing this key displays the sprayers pressure in BAR with 1 decimal The pressure sensor s maximum pressure must be set in ENCODE Pressing this key defines the zero point for the pressure sensor NOTE This key must only be used when the sprayer has absolutely no pressure The displayed pressure will be incorrect if this key is pressed at any other time Pressing the NEXT PAGE key displays the next functions REST DOS Re
157. als for further instruction x Terminal Preferences Terminal Modes CR gt M Line Wrap Inbound Local Echo Outbound _ Sound Cursor r Columns Block Underline 680 C132 v Blink Terminal Font Translations Courier United Kingdom Courier Nex Denmark Norwa T Fixedsys IBM to ANSI Show Scroll Bars Buffer Lines Use Function Arow and Ctrl Keys for Windows Figure 1 Screen shot of settings terminal preferences Windows Terminal Communications Ed Baud Rate C110 C300 600 1200 Cancel 2400 C 4800 9600 19200 Cancel Data Stop Bits 5 C8 1 C15 C2 Choose the Parity Flow Control Connector Com Port that C None CXon Xolt corresponds to Odd C Hardware the serial port C Even None being used Mark C Space Parity Check Carrier Detect Figure 2 Screen shot of settings communications set up Windows Terminal When you have finished set up choose Save in the file menu A dialogue box is shown where it is possible to save the set up to a file The program suggests as the file type Next time you wish to transfer data all you have to do is open this file and all the settings will be correct xd GENERAL FUNCTIONS TEEJET 500
158. amlines cannot be split over 2 bouts The clutches are fitted in the middle of the seed drill and the tramlines are made in one bout See the drawing METHOD B EVEN 5 65 SEED DRILL SIMBA METHOD A UNEVEN In the example to the right the encoded rhythm is 3 Two clutches are fitted in the middle of the drill NB Tramlines are made in bout number 2 when a rhythm track number of 3 is encoded Note where in the first 3 bouts around the field the present bout should A be counted and where the bout should not be counted After each trip around the field the machine drives in the opposite direction Bout counting can be controlled by using either the HOLD key or by using the TRACK keys TEEJET 5000 OPERATORS MANUAL 3 VE ses 325 EM E ES Gigs _ amp Q nmna 5 66 5000 OPERATORS MANUAL SEED DRILL SIMBA METHOD A EVEN A rhythm of 4 is encoded in this example A single S clutch is fitted on the left hand side of the seed 9 drill Tramlines are made A CY bout numbers 2 and 3 split when a rhythm of 4 is encoded n QJ NJ N Note where the first4 P bo
159. ant forward speed and PTO speed and correct encodements SLURRY SPREADER ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements gt gt UC n me mm 1 E S W Y DOSERATE Encode the required application rate if automatic application control equipment is fitted or if a warning is required for incorrect application rate Encode the required rate in TON or M3 cubic metres per hectare The maximum rate that can be encoded is 99 99 Change between TON and by pressing the key STEP Encode the size of the steps for the STEP function This value is the same for both and The maximum step size is 9996 Teejet 7 33 SLURRY SPREADER HORSCH TEEJET 5000 OPERATORS MANUAL
160. anually as follows Volume per revolution x volume weight CALIBRATION FIGURE 5 Pulses per revolution NOTE If after some time it is found that the total amount spread is not the same as the computer has calculated check the machine s settings that the calibration and encodements are correct If all the encodements are correct the following can be done If the fertiliser being used has been stored for a long time or is damper or drier than normal then these conditions can vary from the time of calibration to the present This can be changed by altering the encoded calculated CAL FIG by the amount in percent that the present application varies from the required application Lower CAL FIG lt higher application DISTRIBUTOR WIDTH The working width for the spreader used Each spreader section is encoded individually in centimetres section 1 is the left hand side of the machine NOTE All unused sections must be encoded as 0 The total working width can be seen at the bottom of the display whilst encoding STEP Encode the size of the steps for the STEP function This value is the same for both and The maximum step size is 99 DRIVE FACTOR The speed at which the regulating system adjusts to the correct position Min 1 and Max 500 Normal 100 If the regulation system adjusts to the correct application rate too slowly then the drive factor should be increased If the system is constantly s
161. ar a a a __ _ _ _ _ _ _ _ eee LIII ar r ar ar ar a r ae er ar a a a a ar a ar ar a ar a a a a nar rm a 1 2 6 3 6 4 6 1 6 2 6 a1 e 0 00 cerere a a a SP START gt Y pu Teefet 5 47 SEED DRILL LEMKEN TEEJET 5000 OPERATORS MANUAL METHOD G This method is used when the seed drill is 6 metres wide and the implement used to cultivate the crop is 20 metres wide A fixed rhythm of 10 is used see page 5 55 Example of method G Right The seed drill is fitted with 2x2 magnetic valves on the right hand side of the seed drill and 1 magnetic valve on the left hand side of the seed drill Drilling is started on the right hand side of the field with the track number set to 1 10 as shown on the diagram After the first bout around the field change direction to drive the other way around the filed do this for the third and fourth bout also Tramlines are made when the present track number is 2 5 6 and 9 Only one magnetic valve
162. ard speed is measured from the sensor selected under ENCODE The amount sown in KG measured by a sensor fitted on the drill shaft Calibrating the system is necessary to ensure correct operation and this is done under ENCODE The amount in KG of seed left in the hopper the amount filled in must be encoded before work commences Pressing the NEXT PAGE key displays the next available functions STEP FUNCTION XX Percentile increase of the encoded seed rate The size of the steps is altered in ENCODE Percentile reduction of the encoded NORMAL DOSE RATE seed rate The size of the steps is altered in ENCODE Only displayed if the step feature has been used Normal seed rate Regardless of how many steps the application rate has been increased decreased by pressing this key will return the application rate to normal Pressing this key allows the seed rate to be altered directly from the operation screen see also DOSE RATE in encode 5 18 5000 OPERATORS MANUAL SEED DRILL NORSTEN Pressing the NEXT PAGE key displays the next available functions MANUAL START STOP This function is used to start or stop the drill shaft motor manually MANUAL START can only be used if the machine is at a standstill The display will change to MANUAL STOP as soon as the computer receives a signal from a forward sp
163. ary for correct KG metering If the sown amount is not reduced when making tramlines encode 0 NB Pneumatic seed drills do not reduce the amount when tramlines are being made FORWARD SPEED SENSOR There is a speed sensor fitted to the seed drill that gives a suitable number of pulses for the TeeJet 5000 With the future in mind the computer is also able to receive signals from a sensor fitted onto a tractor or a radar sensor Please refer to chapter 2 for forward speed calibration MANUAL START Encode the number of seconds that the drill shaft will rotate for when MANUAL START is pressed max 20 seconds METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor SENSOR 5 55 SEED DRILL LEMKEN TEEJET 5000 OPERATORS MANUAL WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor PTO SENSOR Encode the number of pulses per revolution for the PTO sensor encode 1 if the TeeJet PTO sensor kit 932 983 is used WARNINGS The following warnings can be set in this menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed KG LEFT Warning ON OFF and amount of kg min in the hopper at which the warn
164. asured press DONE ISLAND DONE When the island is finished press this key PAUSE Pressing this key allows for a break in island measurement Drive back to the position that island measurement was stopped before pressing It is possible to measure more islands by driving to the island boundary and pressing the START key SOIL SAMPLING Select SOIL SAMPLING from the main DGPS menu Select which field the samples are to be taken from the field number can be altered using the numerical keypad The picture to the left is displayed Drive to the first sample point and press SAMPLE After a short wait it is possible to drive to the next sample point When no more samples are required press the DONE key Teefet 9 7 DGPS TEEJET 5000 OPERATORS MANUAL TASK MODE Select TASK MODE from the main DGPS menu Select the task for the field to be worked It is possible to page through the tasks available on the PCMCIA data card by using the horizontal arrow keys The task shown is FERTILISER 2 task information is determined the PC program used to create the task application map XXXXXXXX The area to be worked XX XX HA The task number out of the number of available tasks X XX If the task was been worked on before a small asterisk is sho
165. ative weighing It is not possible to see how much fertiliser is left in the spreader SPREADER ON OFF This key is used as the on off switch for the spreader It is also possible to start stop the spreader using external switch This picture is displayed when spreading When the area override sensor is activated not I counting area 1 is displayed and all sections will disappear 4 66 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL HYDR LIME SPREADER ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements gt gt gt gt 2 ne Qu gt z gt tu OU The effective working width of the spreader must be encoded under DISTRIB WIDTH before DOSE RATE is selected Some spreaders are fitted with a 72 gear It is possible to alter the calculated gear by pressing the key A new calculation must take place if the calculated gear has been altered If the calculated scale is greater than 300
166. been registered this key is only displayed if there is registered data NOTE These registrations can NOT be deleted and data is logged from position 1 again when the memory is full The maximum allowed flow ton min is encoded by pressing the ENCODE DOS Key and thereafter by using the numerical keys If the maximum encoded flow is exceeded an alarm will sound Pressing the OK key cancels the warning The warning will only be given again if the flow ton min drops under and thereafter exceeds the encoded max flow leefet 4 129 FERTILISER DISTRIBUTOR 5000 OPERATORS MANUAL The amount filled into the hopper must be encoded here to be able to see how much fertiliser is left in the hopper NOTE If there is some fertiliser left in the hopper before refilling then this amount must be added to the amount filled thus Amount left in hopper filled amount Kg Left HA LEFT Encode the size of the field to be spread here END TIME is calculated from this encodement CALIBRATION Particular attention must be paid to the calibration procedure as this is the basis for correct operation The amount is measured via a pulse generator mounted on the floor chain The system must be calibrated to ensure correct operation There are 2 methods available to find the calibration figure an automatic method and a manual method AUTOMATIC CALIBRATION This calibration p
167. butor macerator Pressing the NEXT PAGE key displays the first set of functions 7 4 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER OTHER SLURRY SPREADER WITHOUT FLOWMETER TON M3 Slurry consumption in ton m3 uM 7 RPM 1 Revolutions per minute TON M3 The amount of slurry spread since starting This function works as a trip counter and can be deleted in The total counter is also found here RPM 1 The shaft speed of an axle is displayed here Normally the RPM of the distributor macerator MANUAL BOOM SECTIONS SECTION WIDTH When working with 2 boom sections the boom section that is encoded as section 2 can be switched on or off by pressing SECTION WIDTH Area measurement and flow will now be calculated correctly for the section that is still on Conditions for manual section width Only 2 sections must be encoded and the part of the boom to be switched off must be encoded as section 2 BOOM SECTIONS ON OFF The picture shows that the spreader has 2 sections and only one is open The total number of sections must be encoded in DISTRIB WIDTH When the override sensor is activated not measuring I area I is displayed Teejet 7 5 SLURRY SPREADER OTHER TEEJET 5000 OPERATORS MANUAL DAILY USE OF THE SLURRY PROGRAM WITH A FLOWMETER Onc
168. cation rate The application rate is displayed in TON M3 per hectare This rate is calculated from the flow through the flowmeter and area measurement forward speed and working width It is therefore necessary to both drive and spread to see this function NOTE To ensure correct operation the flowmeter must be calibrated the correct wheel circumference and the correct working width must be encoded FORWARD SPEED Forward speed is displayed in kilometres per hour with 1 decimal Forward speed is calculated using the sensor selected under encode wheel tractor wheel spreader or radar NOTE Remember to reset all counters in DATA DELETE before starting SLURRY SPREADER FUNCTIONS wiTH FLOW METERING The metered amount can be displayed in either TON or M3 cubic metres These options are selected in encode under DOSERATE TON M3 Slurry consumption in ton or M3 TON M3 REST amount left in the tank TON M3 MIN Consumption per minute TON M3 The amount of slurry spread since starting This function works as a trip counter and can be deleted in DATA DELETE The total counter is also found here Telet 7 29 SLURRY SPREADER HORSCH TEEJET 5000 OPERATORS MANUAL TON M3 REST The amount remaining in the tank This function presupposes encodement of the tank size TANK VOLUME in encode Every time TANK EMPTY is pressed
169. cation rate if automatic application control equipment is fitted or if a warning is required for incorrect application rate Encode the required rate in TON or M3 cubic metres per hectare The maximum rate that can be encoded is 99 99 Change between and by pressing the key STEP Encode the size of the steps for the STEP function This value is the same for both and The maximum step size is 9996 Teejet 7 7 SLURRY SPREADER OTHER TEEJET 5000 OPERATORS MANUAL TANK VOLUME Encode the effective size of the tank here Check if possible by weighing a few loads to establish the effective TANK VOLUME FILLED VOLUME Encode the amount filled into the tank if FX the tank is only filled half way up Needs only to be encoded if the amount filled differs from the TANK VOLUME Remember Encode the amount filled before leaving encode HA LEFT Encode the size of the field to be spread here END TIME is calculated from this encodement FLOW FIGURE FLOW ON OFF Without flowmeter Set flow to OFF and the application rate is calculated after each load With flowmeter Set to ON and the flowmeter must be calibrated CALIBRATION NOTE Encode a start value of 500 Automatic calibration 1 Fill the slurry spreader to the top so that you know the exact amount 2 Encode the amount in FILLED VOLUME 3 Empty the tank completely but b
170. ct and forward speed will be measured from the radar IMPORTANT Working in crops that are blowing in the wind or working in areas with surface water can affect the accuracy of the radar we recommend using a speed sensor fitted to the tractor under these circumstances WHEEL SPREADER If the spreader is fitted with a speed sensor press the WHEEL SPREADER key The TeeJet 5000 will now receive speed signals from the sensor fitted to the spreader IMPLEMENT SENSOR Using 1 of the following 3 options select how the area counter is to be switched on and off LIFT FERTILISER DISTRIBUTOR PTO The selected sensor is shown at the top of the display METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor SENSOR WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor 4 32 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BOGBALLE REVS SENSOR PTO SENSOR TeeJet PTO sensor kit is used 932 983 encode 1 RPM 1 SENSOR The Begpballe kit be extended with a RPM sensor on the spreader discs The pulses rev Should be set to 1 WARNING ENCODE The following warnings can be set in this menu It is recommended to t
171. ct DOSERATE Encode the specific gravity as 0 00 and the scale setting can be encoded using the numerical keypad ACTUATOR CALIBRATION The system comprising of the computer and an actuator must be calibrated to fit the spreader This calibration must be done at regular intervals during the season i e each time the spreader is connected to the computer Before calibration Move and tighten the scale stop to its highest setting Ensure that the scale stop cannot move during the calibration procedure CALIBRATION Select DOSERATE and press the CALIB ACTUATOR key for approx 3 seconds this will make the actuator move the gate from closed to open and then open to closed NOTE It may be necessary to repeat the actuator calibration a few times if the actuator has been removed to achieve the correct position during a release test 4 42 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL KG LEFT The amount filled into the spreader must be encoded here to be able to see how much fertiliser is left in the hopper NOTE If there is some fertiliser left in the hopper before refilling then this amount must be added to the amount filled thus Amount left in hopper filled amount Kg left HA LEFT Encode the size of the field to be spread here END TIME is calculated from this encodement WEIGHING EIGHING If the spreader is equipped with weigh cells
172. ct PTO Teglet 3 11 SPRAYER TEEJET 5000 OPERATORS MANUAL PRESSURE SENSOR Encode the maximum working pressure for the fitted pressure sensor This maximum Pressure is normally printed on the pressure sensor Zero setting the pressure sensor tarring can be done under both OPERATION and ENCODE TANK VOLUME Encode the sprayer s tank volume when using the optional filling equipment METRE SWITCH Select whether the metre counter is to be started and stopped manually MANUAL or via the implement sensor IMPLEM SENSOR SYSTEM B PLUG There are 2 system plugs on the back of the TeeJet 5000 The System A plug is compatible with o der TeeJet 5000 versions The System B plug is for new connections ACTIVE 0 VOLT sections are opened with OV ACTIVE 12 VOLT Boom sections are opened with 12V ON OFF ON The System B plug is used OFF The System B plug is not used PTO SENSOR Encode the number of pulses the PTO sensor sends per revolution encode 1 if the TeeJet PTO sensor kit is used WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor 3 12 5000 OPERATORS MANUAL SPRAYER WARNINGS The following warning can be set in this menu PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warni
173. ction key displays the following The first menu picture in the task feature shows which implement is being used and the number of tasks that already contain data half filled rectangle The number of empty tasks available in the memory are also displayed the empty rectangle Pressing the Start Task function key displays the following 2 6 Teejet 5000 OPERATORS MANUAL GENERAL FUNCTIONS START TASK Moving the cursor and using the Start function key gives you the possibility to either open a task that has already been worked on or start a new task Note It is only possible to start open i e a sprayer task when sprayer has been selected as the implement This means that only the tasks that relate to the implement used are displayed in the Start Task menu All trip counters area time and quantity will continue from the previous values if an existing task has been selected All trip counters for the task are set to zero if a new task is started The following is displayed after starting a task KEY IN ID NO STOP TASK SEE TASK DELETE TASK Teglet 2 7 GENERAL FUNCTIONS TEEJET 5000 OPERATORS MANUAL ID NO Pressing the
174. cy and the encoded remaining area CLOCK Time shown in hours minutes seconds Clock is set in ENCODE DATE The date shown as day month year Date is set in ENCODE TASK FUNCTION It is possible to record up to 50 individual tasks in the version 4 TeeJet 5000 these 50 tasks are independent of each other and can be shared between all of the different implements If the task feature is not required it is possible use the trip 4 total counters to record data in the version 4 TeeJet 5000 If the Task Feature is required then a task number must be selected before work commences All trip counters area time and quantity will be reset automatically when a new task number is selected The main functions in the Task Feature are as follows Start task Stop task See task Delete task The following is also possible if you possess the correct accessories Print task Necessary accessories TeeJet mobile printer incl cable TeeJet no 905 242 connected to the System A plug on the TeeJet 5000 If the System A socket is used by other equipment use connecting cable TeeJet no 197 130 Data transfer to a PC via the RS232 output Necessary accessories Power supply and serial cable A PC with Windows 3 xx or Windows 95 is necessary to transfer data to a PC via serial cable Teglet 2 5 GENERAL FUNCTIONS TEEJET 5000 OPERATORS MANUAL TASK OPERATION Select the Task Feature as follows Pressing the bottom fun
175. d di E Ee NOTE Greater accuracy can be achieved by weighing the sprayer before and after spraying or by conducting a jug test and comparing the flow in L MIN Pressing the flashing CALC FLOW key will always calculated a new flow figure Method 2 Manual Fill in min 600 litres the more the better Zero the LITRE counter in DATA DELETE Spray 500 litres Read the consumed amount on the indicator on the tank Read the LITRE counter in DATA DELETE Insert the values in the following formula Mee _ Old flow figure x Amount sprayed ee Read litre counter TeeJet 5000 Encode this new value as the new flow figure NOTE Check this calibration at regular intervals if the sprayer is fitted with a standard TeeJet AGRO paddlewheel flowmeter This check is always easy with the TeeJet 5000 as the amount sprayed should be the same as what the TeeJet 5000 displays Changing the paddlewheel in the flowmeter is recommend every other year 3 10 5000 OPERATORS MANUAL SPRAYER BOOM WIDTH The working width for the sprayer If the sprayer is fitted with control valves for each individual boom section boom compensation then encode each boom section by itself starting from the left Encode otherwise the whole boom as 1 section all other sections as 0 Operation Move the cursor to the section to be encoded changed and encode the section width with the numeric keypa
176. d DRIVE FACTOR The speed at which the regulating valve adjusts to the correct position Min 1 Max 500 Normal 100 REGULATION DELAY Encode the number of seconds that regulation is delayed by after the main valve is opened It is possible to encode from 0 to 9 seconds UNIFO PRESS Select ON if the sprayer is fitted with uniform pressure valves OFF if not NOTE Remember to adjust the uniform pressure valves SPEED SENSOR KM H There are 3 different speed sensors to choose from in the TeeJet 5000 v 4 if fitted WHEEL TRACTOR Speed sensor fitted on the tractor The sensor can be built into the tractor s gearbox or rear axle as standard factory fitted or be retrofit on a wheel or drive shaft NOTE Wheelslip will give inaccurate speed readings WHEEL SPRAYER Speed sensor fitted to trailed sprayers This type of sensor will as a rule give a very accurate speed reading RADAR Signal from a radar fitted on the tractor This type of sensor gives a very accurate speed reading on hard surfaces but a high crop and reflecting surfaces water gives an inaccurate reading This type of sensor is not recommended for spraying Please refer to chapter 2 for speed sensor calibration IMPLEMENT SENSOR This sensor starts and stops area measurement This should be connected to the main valve on sprayers Select SPRAYER under encode If a PTO RPM sensor has been fitted then this can be used sele
177. d RPM Fan speed displayed in revolutions per minute VALVE RPM Regulating motor speed displayed in revolutions per minute Selecting this function display s both the desired motor speed calculated from the actual forward speed the actual seed rate and the actual regulating motor speed Pressing the NEXT PAGE key displays the next available functions MANUAL START Manual start and stop of the regulating motor TRACK 1 Moves one step forward in the tramline rhythm TRACK 1 Moves one step backwards in the tramline rhythm MANUAL START This function is used to start or stop the drill shaft motor manually MANUAL START can only be used if the machine is at a standstill The display will change to MANUAL STOP as soon as the computer receives a signal from a forward speed sensor Manual start can be used in difficult conditions i e corners etc and ensures total coverage of the field Pressing the key turns the drill shaft for a number of seconds each key press turns the drill shaft for the number of seconds encoded under ENCODE max 20 seconds Pressing the MANUAL STOP key stops the drill shaft from rotating instantly This function can be used on pneumatic seed drills where the seed route is so long that the tubes are not empty before the drill is raised The seed drill must be raised each time MANUAL STOP has been used TRACK 1 Moves one
178. d press the SELECT key The 2 programs look the same but the Holder program contains certain settings that can only be used with the Holder sprayer It is therefore important that Other is selected for any other sprayers As the 2 programs look the same the following describes the Other Type sprayer 3 2 5000 OPERATORS MANUAL SPRAYER SPRAYER OTHER TYPE It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one SPRAYER OPERATION Once the 2 status screens that show all the encodements have been accepted the following is displayed APPLICATION RATE The primary function under sprayer is application The application rate is shown in litres per hectare based on the flow through the flow meter and the area meter Speed and working width So driving forward or speed simulation and flow through the flow meter is necessary to get a reading NB The correct flow figure forward speed calibration and the correct working wid
179. d Max 500 Normal 25 If the spreader takes too long to find the required application rate then the drive factor should be increased If the spreader constantly changes from too much to too little then the drive factor should be reduced UNIFORM PRESSURE If the spreader s distribution head is fitted with uniform pressure valves return to tank or not ON YES OFF NO Teejet 7 9 SLURRY SPREADER OTHER TEEJET 5000 OPERATORS MANUAL FORWARD SPEED SENSOR The TeeJet 5000 V 4 slurry spreader program gives the option of choosing between 3 different speed sensors Wheel tractor Wheel spreader Radar WHEEL TRACTOR The speed signal can come from a sensor fitted in the gear box or on a drive shaft or from a sensor fitted on a wheel depending on the make and model of the tractor used for slurry spreading RADAR If the tractor is fitted with radar then select RADAR and forward speed will be measured from the radar Radar and the number of pulses per metre will be displayed at the top of the screen IMPORTANT Working in crops that are blowing in the wind or working in areas with surface water can affect the accuracy of the radar we recommend using a speed sensor fitted to the tractor under these circumstances WHEEL SLURRY SPREADER If the slurry spreader is fitted with a speed sensor then press the WHEEL SLURRY key The TeeJet 5000 will now use this sensor for forward speed measurement
180. d the number of pulses per metre will be displayed at the top of the screen IMPORTANT Working in crops that are blowing in the wind or working in areas with surface water can affect the accuracy of the radar we recommend using a speed sensor fitted to the tractor under these circumstances WHEEL SLURRY SPREADER If the slurry spreader is fitted with a speed sensor then press the WHEEL SLURRY key The TeeJet 5000 will now use this sensor for forward speed measurement Please refer to chapter 2 for forward speed calibration IMPLEMENT SENSOR SLURRY SPREADER Area measurement is started stopped by pressing the HOLD key see SLURRY SPREADER OPERATION PTO Area measurement is started stopped by a sensor fitted to the PTO shaft area measurement is stopped when the RPM is lower than 50 RPM PUMP Area measurement is started stopped by a RPM sensor fitted to the pump area measurement is stopped when the RPM is lower than 50 7 24 Teglet TEEJET 5000 OPERATORS MANUAL SLURRY SPREADER OTHER TYPE HYDR METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor IMPLEM SENSOR WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor REVS SENSOR Encode the number of pulses per revolution given for the individual se
181. displayed in KPH with 1 decimal Forward speed is calculated from the signal from the speed sensor selected in encode wheel tractor wheel spreader or radar APPLICATION RATE IN KG HA The present application rate in Kg ha Calculated from the number of pulses from the floor chain and area measurement speed and working width It is therefore necessary to drive and spread at the same time to get a reading for this function NOTE Correct calibration of forward speed and weight per pulse plus correctly entered working width are essential for accurate operation FERTILISER DISTRIBUTOR FUNCTIONS Step dosage Increase Step dosage Reduction DOSE RATE NORMAL Encoding the required application rate or return to normal after using the step key XX Percentile increase of the encoded application rate The size of the steps is altered in encode XX Percentile reduction of the encoded application rate The size of the steps is altered in encode NORMAL Only displayed if the step function has been used Normal application rate Regardless of how many steps the application rate has been increased decreased by pressing this key will return the application rate to normal DOSE RATE Pressing this key allows the application rate to be altered directly from the operation screen see also DOSE RATE in encode Pressing the NEXT PAGE k
182. ds when PRE CALIB Has been pressed to ensure that the feed rollers are full of seed Remember to empty the calibration tray bucket again before proceeding This screen is now displayed LOAD FIG The previous load figure NO OF PULSES The pulses are counted during calibration NO OF CALIB Shows the number of calibrations The drill shaft will rotate for 10 seconds when the CALIB Key is pressed The number of calibrations can be increased for each press of the key This gives the possibility of varying the amount and therefore the weight of the released seed so weighing in relation to the type of scales being used is as good as possible leefet 5 53 SEED DRILL LEMKEN TEEJET 5000 OPERATORS MANUAL The screen changes once the drill shaft has rotated for the number of seconds encoded The weight of the released grain is encoded in grams under WEIGHT CALC flashes Pressing CALC Will calculate a new load figure which is displayed at the top of the screen The calibration procedure is now finished pressing the return key brings the ENCODE menu back STEP The size of the steps this percentile value is the same for both and KG LEFT To see how much seed is left in the hopper
183. e TeeJet5000 displays the picture to the left It is possible to page through the saved calibration results using the NEXT PAGE key 2 Pressing the ACCEPT key uses the selected calibration STEP Encode the size of the steps for the STEP function This value is the same for both and The maximum step size is 99 KG LEFT The amount filled into the spreader must be encoded here to be able to see how much fertiliser is left in the hopper NOTE If there is some fertiliser left in the hopper before refilling then this amount must be added to the amount filled thus Amount left in hopper filled amount Kg left KG LEFT can be set as an alarm HA LEFT Encode the size of the field to be spread here END TIME is calculated from this encodement METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor IMPLEM SENSOR WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor 4 122 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH AXERA H PTO SENSOR The number of pulses per revolution for the PTO shaft WARNING ENCODE The following warnings can be set in this menu It is recommended to turn all warnings which not
184. e Tramlines are made leefet 5 3 SEED DRILL OTHER TEEJET 5000 OPERATORS MANUAL TRAMLINE CONTROL The primary function for seed drills is the track number The following picture is displayed 3 RACK NO Bout number Track number The bout number is the present bout being driven in the field counts 1 each time the drill is lifted The track number is what has been encoded see The TeeJet 5000 has 2 different methods of controlling the tramlines A and B The method is selected under ENCODE METHOD This method is a new and logical method of making tramlines If the tramlines are to be made on uneven bouts 3 5 7 or 9 then the tramlines will always be made in the middle bout Two clutches are fitted to the middle of the drill See the drawing for METHOD A UNEVEN If the tramlines are to be made on even bouts 2 4 6 or 8 then the tramlines are split between the 2 middle bouts The field must be sown up and down as there is only 1 clutch fitted on one side of the seed drill See the drawing for METHOD A EVEN The tramlines are displayed for this method thus 5 4 5000 OPERATORS MANUAL SEED DRILL OTHER METHOD B This method is older and better known Tramlines are made when the present bout is the same as the track number The operator must know how the field has been started If tramlining is required in on uneven bouts
185. e increase XX Step dosage decrease DOSE RATE NORMAL Encoding the required application rate or return to normal after using the step key XX Percentile increase of the encoded application rate The size of the steps is altered in encode XX Percentile reduction of the encoded application rate The size of the steps is altered in encode NORMAL Only displayed if the step feature has been used Normal application rate Regardless of how many steps the application rate has been increased decreased by pressing this key will return the application rate to normal DOSE RATE Pressing this key allows the application rate to be altered directly from the operation screen see also DOSE RATE in encode Pressing the NEXT PAGE key displays the next functions DISTRIB RPM of the distributor PUMP RPM of the pump FULL TANK When the tank is full DISTRIBUTOR RPM of the distributor is displayed The number of pulses per revolution is encoded under REVS SENSOR in ENCODE PUMP The RPM of the pump is displayed The number of pulses per revolution is encoded under REVS SENSOR in ENCODE FULL TANK Pressing this key transfers the amount encoded under TANK VOLUME to TON M3 LEFT presupposes that the amount has been encoded Use this function each time the tank is refilled Pressing the NEXT PAGE key displays the next functions When the AUTO MAN key
186. e when the key proportional valve when the key is released the valve shuts is released the valve shuts OUT 2 Not used Completely opens the auger proportional valve when the key is released the valve shuts OUT 3 Not used Not used OUT 4 Not used Not used 1 2 Not used 2 24 5000 OPERATORS MANUAL GENERAL FUNCTIONS TEST INPUT RAUCH AERO RAUCH BETA DELTA TRAIL 1 Not used Signal from shaft speed sensor RPM 1 TRAIL 2 Signal from sensor on feed Not used rollers TRAIL 4 Signal from speed sensor fitted Speed signal from trailed to trailed machines implement TRAIL 7 Area override on off from the Area override on off signal from machine implement TRAIL 8 Not used Not used TRAIL 15 Not used Not used TRAIL 16 Not used Not used BOM 1 12 Error is displayed as no boom Error is displayed as no boom interface is connected interface is connected TEST OUTPUT OUT 1 Fully opens the reg Valve Signal to close the gate left momentarily and the feed rollers rotate at full speed The shuts and the feed rollers stop instantly when the key is released OUT 2 Not used Signal to open the gate left OUT 3 Not used Signal to close the gate right OUT 4 Not used Signal to open the gate right 1 2 Not used Shows the position of the actuators Teglet 2 25
187. e all of the encodements have been accepted proceed as follows Start spreading and each time the area override sensor is activated implement sensor the following warning is displayed When this screen is displayed you have the following options If the machine is turning at the headland then continue driving and the warning screen will disappear when spreading starts again If you stop spreading temporarily without the tank being empty press PAUSE to remove the warning The warning screen will disappear when spreading starts again If the tank is empty press TANK EMPTY The value encoded under TANK VOLUME will be automatically transferred to TON M3 LEFT DAILY USE OF THE SLURRY PROGRAM WITHOUT A FLOWMETER Once all of the encodements have been accepted proceed as follows Start spreading and each time the area override sensor is activated implement sensor the following warning is displayed When this screen is displayed you have the following options If the machine is turning at the headland then continue driving and the warning screen will disappear when spreading starts again If you stop spreading temporarily without the tank being empty press PAUSE to remove the warning The warning screen will disappear when spreading starts again If the tank is empty press TANK EMPTY The following 2 things
188. e encoded here PTO Warning ON OFF and MAX MIN limits for the PTO sensor KM H Warning ON OFF MAX MIN limits for forward speed SLIP Warning ON OFF and MAX MIN limits for wheel slip NOTE It is recommended to switch all un required warnings to OFF DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY 8 6 Teefet DGPS INTRODUCTION ipu 9 2 SELECTING THE 225 66 9 3 DGPS STATUS ed ttim ua 9 4 Iu ue ap 9 4 DGPS FUNCTIONS tid teet dud LEE E 9 5 FIELD MEASUREMENT et etit ne once i beet niea 9 5 SOIL SAMPLING DUDEN EM EMEND 9 7 ETE Err Ep Eeh 9 8 TEEJET 5000 DATALOG E 9 8 GPS OR RSE Tai e E E 9 9 WARNING i hieer ce Sa 9 9 zm pieni E 9 10 DGPS TEEJET 5000 OPERATORS MANUAL INTRODUCTION TeeJet 5000 with DGPS functions Task function that controls the application rate for various implements depending on an application map made via a PC Field boundary measurement plus island measurement which transferred to a PC Soil sampling with the position of each individual sample point Data Logging recording of wha
189. e result in using the arrow keys press thereafter the SELECT key If the CALCULATE key is pressed the calibration will be used until another calibration procedure takes place or another calibration previously saved is selected If the metered encoded amounts from the calibration procedure are not accurate enough for the TeeJet 5000 a warning will be given and the calibration procedure must be carried out again 4 110 TEEJET 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH BETA DELTA If there are previously saved calibration results the procedure is as follows 1 Press the CALIB PROCED key and the TeeJet5000 displays the picture to the left It is possible to page through the saved calibration results using the NEXT PAGE key 2 Pressing the ACCEPT key uses the selected calibration STEP Encode the size of the steps for the STEP function This value is the same for both and The maximum step size is 99 KG LEFT The amount filled into the spreader must be encoded here to be able to see how much fertiliser is left in the hopper NOTE If there is some fertiliser left in the hopper before refilling then this amount must be added to the amount filled thus Amount left in hopper filled amount Kg left KG LEFT can be set as an alarm HA LEFT Encode the size of the field to be spre
190. e sure to stop emptying as soon as the tank is empty as air going through the flowmeter can cause false readings 4 Encode 0 00 using the numerical keypad under TANK REM VOL 5 Press the flashing CALC FLOW key 6 The flow figure is calculated NOTE Greater accuracy can be achieved by weighing the loads A new flow figure is calculated each time CALC FLOW is pressed 7 8 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER OTHER TYPE Manual calibration The flow figure can also be calculated manually as follows Fill the slurry spreader to the top so that you know the exact amount Reset the amount counter in DATA DELETE Empty the tank completely Read the amount in DATA DELETE Place the value in the following formula of eS S Old flow figure x the amount spread NEW FLOW FIGURE The amount read in Data delete TeeJet 5000 6 Encode this new flow figure using the numerical keypad BOOM WIDTH The working width of the spreader If the system is fitted with control valves for each section then the individual section width must be encoded here left boom section 1 If the spreader does not have individual sections then encode the whole spreader width as section 1 all other sections must be encoded as 0 DRIVE FACTOR The speed at which the regulating valve adjusts to maintain the correct application rate Min 1 an
191. e the warning for approx 15 seconds WARNING ENCODE The following warnings can be set in this menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warning ON OFF and MAX MIN limits for wheel slip in KG LEFT Warning ON OFF and amount of kg min in the hopper at which the warning is wanted D SHAFT Warning ON OFF if the drill shaft stops turning HOPPER Warning ON OFF for empty seed hopper RPM Warning ON OFF and MIN MAX limits for fan RPM pneumatic seed cmm under CLUTCH SENSOR NB If the warning for RPM is on then the computer will not allow sowing to commence before it receives signals from the fitted RPM noone is off then sowing is independent of the RPM sensor CLUTCH Warning ON OFF for if the clutches used for tramlining stop working DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY 5 30 Seed drill Lemken EEMKEN SEED DRILL ei 5 32 FER EREREER FER ERER HEP FERE ERE EH 5 33 TRAMLINE 5 33 UNIX sna ue P 5 33 KOMA e c 5 33 HOLD KEY ewm H 5 34 SELECTABLE SEED
192. earching up amp down for the correct application rate then reduce the drive factor leefet 4 131 FERTILISER DISTRIBUTOR TEEJET 5000 OPERATORS MANUAL REVS SENSOR Encode the number of pulses per revolution for the individual RPM sensors FORWARD SPEED SENSOR The TeeJet 5000 V 4 fertiliser distributor program gives the option of choosing between 3 different speed sensors Wheel tractor Wheel spreader Radar WHEEL TRACTOR Speed sensor fitted on the tractor The sensor can be built into the tractor s gearbox or rear axle as standard factory fitted or be retrofit on a wheel or drive shaft NOTE Wheelslip will give inaccurate speed readings WHEEL SPREADER Speed sensor fitted to trailed spreaders This type of sensor will as a rule give a very accurate speed reading RADAR Signal from a radar fitted on the tractor This type of sensor gives a very accurate speed reading on hard surfaces but a high crop and reflecting surfaces water can give an inaccurate reading Please refer to chapter 2 for speed sensor calibration 4 132 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR REI IMPLEMENT SENSOR The implement sensor area override is the sensor that starts and stops the area counter There are 3 possibilities in this program LIFT FERTILISER DISTRIBUTOR PTO The selected sensor is displayed on the screen
193. ed by radar This function is active only if a radar is mounted and ON is encoded PTO Revolutions per minute on the PTO This function is active only if a PTO sensor has been mounted METRE Travelled distance measured in metres and based on chosen speed sensor Is started and stopped by the implement sensor or manually by pressing METRE Chosen under encode BATT Battery voltage supply for the computer AREA FUNCTIONS Travelling efficiency x HA Area HA LEFT Remaining area Travelling efficiency The size of the area worked present speed and with the present implement working width HA Area counter Worked area in hectares since zeroing NB A total counter for the area is found in DATA DELETE HA LEFT Remaining area Of the size of the field is encoded before start in the remaining area can be read here TIME FUNCTIONS TIMER Working time in hours and minutes END TIME time when the work will be finished CLOCK Time in hours minutes seconds DATE Day month year 2 4 Teejet 5000 OPERATORS MANUAL GENERAL FUNCTIONS TIMER Used for measuring the time spent at a certain job The timer can be stopped and started manually NB the implement sensor does not control the timer END TIME The time when the present job is expected to be finished calculated on the present travelling efficien
194. ed with magnets 3 Mark the ground again 4 Measure the distance between the 2 marks in centimetres and divide by the number of rotations and the number of magnets fitted on the wheel The result is the distance per pulse and can be encoded in centimetres with 3 decimals see the following formula Example The distance between the 2 marks is 52 80 metres 5280 centimetres The wheel has turned 10 times The wheel is fitted with 4 magnets 5280 Distance between marks in cm 10 Wheel rotations x 4 Magnets E calculated figure is encoded thus 1 Press the CALIB CALC key 2 Encode the value using the numeric keypad 3 The encoded figure can be deleted at anytime by pressing the C key 2 18 Teejet 5000 OPERATORS MANUAL GENERAL FUNCTIONS AUTOMATIC SPEED SENSOR CALIBRATION 1 Measure a stretch of 100 metres and drive to the start mark 2 Press the CALIB CALC Key twice and the following is displayed 3 Drive the 100 metres and stop exactly at the stop mark 4 Ifthe computer has received enough pulses CALC WHEEL will be displayed Press this key and the calibration procedure is finished The calculated value is displayed at the top of the screen Teefet 2 19 GENERAL FUNCTIONS
195. ed with the spreader to ensure correct operation This calibration must take place the first time the computer is connected to the spreader and each time the computer is connected to another spreader 4 48 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL HYDR B BREDAL S FERTILISER SPREADER Select fertiliser distributor from the main menu as follows 1 Move the cursor using the arrow keys to FERTIL DISTRIB Press the SELECT key 2 Main menu 3 select fertiliser distributor 4 ACCEPT or SELECT TYPE 5 Select type 6 is now possible to choose between the displayed types 7 Select fertiliser distributor type 8 Accept type It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one
196. eed rollers FERTILISER DISTRIBUTOR ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements 00 Of WS gt 4 95 FERTILISER DISTRIBUTOR RAUCH AERO TEEJET 5000 OPERATORS MANUAL WORKING WIDTH The working width for the spreader being used Each spreader section is encoded individually in centimetres section 1 is on the left hand side of the machine NB All unused sections must be encoded as 0 The total working width can be seen at the bottom of the display under encode FORWARD SPEED SENSOR The TeeJet 5000 V 4 fertiliser distributor program gives the option of choosing between 3 different speed sensors Wheel tractor Wheel spreader Radar WHEEL TRACTOR Speed sensor fitted on the tractor The sensor be built into the tractor s gearbox or rear axle as standard factory fitted or be retrofit on a wheel or drive shaft NOTE Wheelslip will give inaccurate speed readings WHEEL SPREADER Speed sensor fitted to trailed spreaders This type of s
197. eed sensor Manual start can be used in difficult conditions i e corners etc and ensures total coverage of the field Pressing the key turns the drill shaft for a number of seconds each key press turns the drill shaft for the number of seconds encoded under ENCODE max 20 seconds Pressing the MANUAL STOP key stops the drill shaft from rotating instantly This function can be used on pneumatic seed drills where the seed route is so long that the tubes are not empty before the drill is raised The seed drill must be raised each time MANUAL STOP has been used MANUAL TRACK ADJUSTMENT TRACK 1 Moves one step forward in the tramline rhythm TRACK 1 Moves one step backwards in the tramline rhythm Pressing the NEXT PAGE key displays the next available functions RPM NB RPM is only displayed if it is selected under ENCODE pneumatic machines Displays RPM for the fan on pneumatic machines if a sensor is fitted Pressing the RETURN key displays the menu for the selectable functions leefet 5 19 SEED DRILL NORDSTEN TEEJET 5000 OPERATORS MANUAL SELECTING THE TRACK RHYTHM To meet the different needs of different markets the TeeJet 5000 has 2 methods of controlling the how the tramlines are made The method to be used is selected under encode METHOD B This method is the most gt traditional and the mo
198. eing driven in the field counts 1 each time the drill is lifted The track number is what has been encoded see The TeeJet 5000 has 2 different methods of controlling the tramlines A and B The method is selected under ENCODE METHODA This method is a new and logical method of making tramlines If the tramlines are to be made on uneven bouts 3 5 7 or 9 then the tramlines will always be made in the middle bout Two clutches are fitted to the middle of the drill See the drawing for METHOD A UNEVEN If the tramlines are to be made on even bouts 2 4 6 or 8 then the tramlines are split between the 2 middle bouts The field must be sown up and down as there is only 1 clutch fitted on one side of the seed drill See the drawing for METHOD A EVEN The tramlines are displayed for this method thus METHOD B This method is older and better known Tramlines are made when the present bout is the same as the track number The operator must know how the field has been started If tramlining is required in on uneven bouts 3 5 7 or 9 the system works well Tramlines are made using 2 clutches fitted in the middle of the seed drill when the present bout number is the same as the encoded track number See the drawing METHOD B UNEVEN If the tramlines are to be made on even bouts 2 4 6 or 8 then the operator must drive around the field with only one half of the seed drill open This is necessary as the tr
199. elected BETA or DELTA Changing between automatic or manual operation Step dose rate NOTE Only active in automatic drift The application rate can be increased or decreased by an encoded percentile amount The rate can be altered for both sides or the left hand side or the right hand side by pressing the NEXT PAGE key see the following pictures When used the percentile increase or reduction flashes in the lower part of the display NORMAL RPM or POS AUTO MAN Pressing the NORMAL key returns the application rate to normal regardless of how many steps the rate has been increased or decreased by NOTE The step dose rate screen is left by pressing the return key This function is displayed in the DELTA Program Pressing this key displays the speed of the spinning discs The minimum and maximum disc speed can be set as a warning under This function is displayed the BETA Program This function is displayed in the DELTA Program on the next page The value displayed refers to the position of the actuator the gate opening Pressing this key changes between automatic and manual application control During manual operation flashes at the bottom of the display Pressing the NEXT PAGE key displays the ne
200. elete key is used together with the numerical keys for encoding It deletes the selected value Also used for zeroing the pulse counters in TEST INPUT This key is used for switching the display light on and off switching the light on and off can also be done in the CONTRAST menu The numerical keys are used for encoding 1 4 leefet General functions c zr MIU Buy S mU EE 2 2 FUNCTION cce EP 2 2 BASIC agen ase ate Tener ee Tr 2 2 STATUS SCREEN sinaia 2 3 TRACTOR PDUNGTIONOS 3 3 03599599594 99 0 902 99 08 0 9990499 9 000 5 95995 9 5 004 2 4 AREA FUNC TIONS oir ee TRU UD US 2 4 2 4 TASK FUNCTION rosei 2 5 TASK OPERATION aoa aaa aaa 2 6 STARI 2 7 2 8 STOP poo eerie eee 2 8 SEE Wie de c 2 8 DELETE qt tw 2 9 a MESS uec ag 2 9 PRINT Pr zn 2 9 PRIN MQ 2 10 PRINTING TASKS VIA Oe 2 10 CONNECTION OF THE TEEJET 5000 2 10 SETTING TERMINAL UP 2 11 SETTING HYPER TERMINAL UP ossis tnn spur cabe situa 2 12 RECEIVE TES Ferren tra 2 14 EDITING THE
201. elta og PK1500 RAUCH BETA DELTA FERTILISER 4 102 FERTILISER DISTRIBUTOR OPERATION eter odit 4 103 FERTILISER SPREADER FUNCTIONS scciccsiesesceceacntesnnncssadussenseteentencdesasainteeeceneduedon 4 103 1 AUTOMATIC APPLICATION 2 4222444 1111 4 104 2 MANUAL APPLICATION 4 106 FERTILISER DISTRIBUTOR ENCODE irap sare ea n 4 108 WORKING WID Hi 4 108 SPEED SENSOR ieaiao 4 109 WHEEL TRACTOR eee 4 109 WHEEL SPREADER 4 109 RADAR 4 109 FERTILISER CALIBRATION PROGEDURE erento rantes 4 109 FERTILISER GALIBRA TIONG 0203 9 006090000 4 110 c r mE 4 111 pem E 4 111 PUP LEED 4 111 METRE SWITCH PN Oc 4 111 WORK HOUR ON OFF 4 111 WARNING ENCODE 4 112 DATE qm 4 112 OPFESET MIU MEUM MEE ree 4 112 Teglet 4 101 FERTILISER DISTRIBUTOR RAUCH BETA DELTA TEEJE
202. ensor will as a rule give a very accurate speed reading RADAR Signal from a radar fitted on the tractor This type of sensor gives a very accurate speed reading on hard surfaces but a high crop and reflecting surfaces water can give an inaccurate reading Please refer to chapter 2 for speed sensor calibration FERTILISER CALIBRATION PROCEDURE The computer allows you to save up to 3 different calibrations e g different fertiliser types Each calibration represents the individual test plus 3 fixed but user defined application rates i e 150 kg ha 200 kg ha 250 kg ha A new calibration must be carried out each time 1 The first time the spreader is used 2 When the working width is changed 3 The fertiliser type is changed A new calibration should take place when 1 If you suspect that the flow characteristics of the fertiliser have changed i e a new load 2 Change of weather temperature and moisture Even when the above factors have been taken into consideration fertiliser calibration should be checked at regular intervals 4 96 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH AERO FERTILISER CALIBRATION Prepare the spreader as follows before the fertiliser calibration procedure takes place 1 To ease the calibration procedure it is only necessary to calibrate one section of the spreader Using the switch box open this one section and shut all of the ot
203. er 2 for forward speed calibration 6 6 Teglet 5000 OPERATORS MANUAL BALER REVS SENSOR The number of pulses per revolution for the individual shaft speed sensors is encoded here PTO SENSOR Ifthe TeeJet PTO sensor is used 932 983 then encode 1 1 If the TeeJet sensor is used 930 983 then encode 1 RPM 2 If the TeeJet sensor set is used 930 983 then encode 1 If the TeeJet sensor is used 930 983 then encode 1 WARNINGS PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for forward speed SLIP Warning ON OFF and MAX MIN limits for wheel slip in RPM1 Warning ON OFF and MAX MIN limits for revolutions Encode as RPM 2 Warning ON OFF MAX MIN limits for revolutions Encode as RPM RPM3 Warning ON OFF and MAX MIN limits for revolutions Encode as RPM DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY Teefet 6 7 BALER TEEJET 5000 OPERATORS MANUAL 6 8 Slurry spreader N SLURRY SPREADER OTHER prx T 1 SLURRY SPREADER HYDRAULIC 7 15 SLURRY SPREADER FORSCH 7 27 SLURRY SPREADE
204. er can be split into sections If regulation is required when one or more sections are closed then uniform pressure should be set to OFF If no regulation is required when one or more sections are closed then set uniform pressure to ON PULS REV Encode the number of pulses per revolution for the RPM 2 sensor sow axle 4 19 FERTILISER DISTRIBUTOR OTHER WITH REG TEEJET 5000 OPERATORS MANUAL FORWARD SPEED SENSOR The TeeJet 5000 V 4 fertiliser distributor program gives the option of choosing between 3 different speed sensors Wheel tractor Wheel spreader Radar WHEEL TRACTOR Speed sensor fitted on the tractor The sensor can be built into the tractor s gearbox or rear axle as standard factory fitted or be retrofit on a wheel or drive shaft NOTE Wheelslip will give inaccurate speed readings WHEEL SPREADER Speed sensor fitted to trailed spreaders This type of sensor will as a rule give a very accurate speed reading RADAR Signal from a radar fitted on the tractor This type of sensor gives a very accurate speed reading on hard surfaces but a high crop and reflecting surfaces water can give an inaccurate reading Please refer to chapter 2 for speed sensor calibration IMPLEMENT SENSOR The implement sensor area override is the sensor that starts and stops the area counter There are 3 possibilities in this program LIFT FERTILISER DISTRIBUTOR PTO The selected sensor is d
205. er must be calibrated with the spreader to ensure correct operation This calibration must take place the first time the computer is connected to the spreader and each time the computer is connected to another spreader 4 36 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL BREDAL FERTILISER DISTRIBUTOR Select fertiliser distributor from the main menu as follows 1 Move the cursor using the arrow keys to FERTIL DISTRIB Press the SELECT key 2 Main menu select fertiliser distributor 3 ACCEPT or SELECT TYPE 4 Select type 5 It is now possible to choose between the displayed types 6 Select fertiliser distributor type 7 Accept type It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one
206. eration MAN flashes at the bottom of the display Pressing the NEXT PAGE key displays the next functions Increased application rate Decreased application rate POS Actuator position gate opening 4 118 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH AXERA H Each key press increases the application rate If the key remains pressed then the application rate is increased by a suitable amount The actual application rate can be seen on the display Each key press decreases the application rate If the key remains pressed then the application rate is decreased by a suitable amount The actual application rate can be seen on the display POS Pressing this key displays the gate position changes between the left and right hand side FERTILISER DISTRIBUTOR ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements 00 GE gt WORKING WIDTH The working width for the spreade
207. es each function set individually leefet 4 91 FERTILISER DISTRIBUTOR RAUCH AERO TEEJET 5000 OPERATORS MANUAL 1 AUTOMATIC APPLICATION CONTROL KG HA1 KG HA2 These 3 application rates are set in ENCODE and can be selected under OPERATION KG HA3 Pressing one of these keys displays the encoded required application rate Not the actual application rate Before accurate automatic application control can take place it is important to calibrate the system using the fertiliser to be spread To minimize the risk of incorrect operation application the following automatic warnings may be displayed DOSERATE If the required application rate can not be achieved WRONG SPREADER WIDTH If the spreader width being used is not the same as the spreader used when calibrating Pressing the NEXT PAGE key displays the next functions Step dosage increase Step dosage decrease NORMAL Return to the selected application rate XX Percentile increase of the encoded application rate The size of the steps is altered in encode Percentile reduction of the encoded application rate The size of the steps is altered in encode NORMAL Normal application rate Regardless of how many steps the application rate has been increased decreased by pressing this key will return the application rate to normal Pressing the N
208. etween the satellites that signals are being received from DOSERATE The application rate decided by the application map IMPORTANT Before the data card is removed from the DataLink module after executing any of the following DGPS functions press the RETURN key until the main DGPS menu is displayed and switch the power off to the DataLink module 9 4 Teglet 5000 OPERATORS MANUAL DGPS DGPS FUNCTIONS FIELD MEASUREMENT Select the field to be surveyed by entering the field number using the numerical keypad Press thereafter The picture to the left is displayed if the field has been measured before CONTINUE Continue with the previously surveyed field OVERWRITE The existing field measurements are overwritten ABORT Abort the present survey CONTINUE Pressing this key continues the field survey OVERWRITE Pressing this key overwrites the previously measured field and starts the field from new ABORT Pressing this key returns the screen to SELECT DGPS FUNCTIONS Teglet 9 5 DGPS
209. ey displays the next functions 4 15 FERTILISER DISTRIBUTOR OTHER WITH REG TEEJET 5000 OPERATORS MANUAL KG Consumption in Kg since the last reset in DATA DELETE KG LEFT KG remaining in the hopper amount filled must be encoded before start RPM 1 Shaft speed of axle 1 KG Kg consumed measured via the pulse generator on the sow axle This function presupposes correct calibration of the system amount per pulse KG LEFT The amount remaining in the hopper Presupposes encoding the amount filled before start done in encode RPM 1 Shaft speed of axle no 1 Pressing the NEXT PAGE key displays the last available functions RPM 2 Shaft speed of axle no 2 sow axle Pressing the NEXT PAGE key displays the first available functions SECTION ON OFF The picture to the left shows a spreader with 2 sections encoded where one is open and one is closed The total number of sections is set under encode When the area override sensor is activated not counting 1 area is displayed all sections will disappear 4 16 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR OTHER TYPE WITH REG FERTILISER DISTRIBUTOR ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodeme
210. fertiliser is left in the hopper NOTE If there is some fertiliser left in the hopper before refilling then this amount must be added to the amount filled thus Amount left in hopper filled amount Kg left 4 7 FERTILISER DISTRIBUTOR OTHER TEEJET 5000 OPERATORS MANUAL HA LEFT Encode the size of the field to be spread here END TIME is calculated from this encodement WEIGHING Selecting this gives 3 options WEIGHING v Direct weighing using weigh cells PULSE WEIGHING Amount metering using pulse generators RPM 2 Shaft speed for axle no 2 The selected option is displayed at the top of the screen above a broken line WEIGHING The weigh system must be calibrated if this option is selected 1 Press CALC And the picture to the left is displayed 2 Press TARRING with an empty spreader to zero set the weight 3 Fill the spreader with a known amount As large an amount as possible gives the best result must be min 5096 of the spreader s capacity Move the cursor to CALIB WEIGHT and encode the amount filled into the spreader using the numerical keypad 4 Press the flashing CALC LOAD FIG key The system is calibrated The calculated LOAD FIGURE is shown at the top of the screen note this figure if the system is also used with other weigh cells NOTE Check the weigh cell s calibration at regular intervals
211. first two chapters describe the functions available for all implements In the SYSTEM menu all sensors can be tested in TEST INPUT and the outputs to valves actuators etc in TEST OUTPUT This is described in chapter 2 The SYSTEM DATA menu has special encodements to which the operator has no access The required operating language can be selected in LANGUAGE The TeeJet 5000 standard fitting kit for one tractor includes Junction box trailer plug wheel sensor implement sensor plus all necessary parts for fitting This equipment allows forward speed area driven distance and time functions to be displayed The system has been prepared for countless extensions These will however often depend on the tractor and implement type TeeJet AGRO offers specially designed fitting kits for most commonly known makes and models Ask your dealer or directly to TeeJet AGRO NOTE Please unfold the page in chapter 11 before proceeding 1 2 5000 OPERATORS MANUAL CONSTANT KEYS RETURN KEY gt TRACTOR INFO KEY CONTRAST GENERAL USE The return key is used for returning to previous displays It takes one display picture each time the key is pressed The key is also used for accepting the status screens for encoded values see STATUS SCREEN By pressing this key a number of important tractor functions can be displayed regardless of which function has been
212. function is started stopped manually via the function key in the operation menu or by the selected implement sensor REVS SENSOR Encode the number of pulses per revolution given for the individual sensors 411 FERTILISER DISTRIBUTOR OTHER TEEJET 5000 OPERATORS MANUAL WARNING ENCODE The following warnings can be set in this menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warning ON OFF and MAX MIN limits for wheel slip in KG LEFT Warning ON OFF and amount of kg min at which warning is wanted this warning is only available if PULSE WEIGHING has been selected RPM 1 Warning ON OFF and MAX MIN limits for shaft speed Encode in RPM RPM 2 Warning ON OFF and MAX MIN limits for shaft speed Encode in RPM only available if RPM has been selected NB The encoded limits must exceed the limits encoded If a warning is required when an axle stops 0 RPM then set the minimum limit to 1 DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY 4 12 Fertiliser distributor Other type with reg FERHLISER DISTRIBUTOR RE RED FU d 4 14 FERTILISER DISTRIBUTOR 4 15 FERTILISER DISTRIBUTOR
213. g diagram If the drive shaft solution is required then a bi polar sensor must be used This sensor is different than the supplied sensor and should be ordered separately 2016 6001 distance between the sensor and the magnets must be 2 3 mm when using this type of sensor and the 2 magnets must have opposite poles facing the sensor i e one magnet with the yellow spot facing the sensor and the other magnet facing the opposite direction 12 10 Teglet 5000 OPERATORS MANUAL FITTING INSTRUCTIONS FITTING THE AREA OVERRIDE SENSOR The area override sensor stops the area counter when the implement is not in operation Most implements use the three point linkage and are raised lowered so the most universal solution is to fit the area override sensor on the lift arms The sensor can be fitted in other positions PTO handle hydraulic cylinder handles etc as long as there is a mechanical movement of min 50 mm The distance between the sensor and the magnet must not exceed 5 mm An electrical signal from i e electrically controlled lift arms sprayer switch box etc can be used as an area override sensor The signal must change to 0V ground when the area counter is to be stopped LEVE ELECTRI ELECTRIC FITTING INSTRUCTIONS TEEJET 5000 OPERATORS MANUAL FITTING THE BREAK AWAY PLUG The supplied breakaway plug with cable should
214. g in the field with an implement and sensors selected you must not return to the BASIC MENU or change to another implement If this is attempted the TeeJet 5000 will display MENU CHANGE PROHIBITED This is necessary to avoid incorrect measurements STATUS SCREEN Each time the OPERATION MENU of an implement is selected or you leave an encode menu the status screen will automatically appear All the encoded values are displayed Check and accept all the values on the status screen before proceeding by using the RETURN KEY NB Before start remember to zero all relevant counters area litre diesel counter etc in DATA DELETE if required You can select the following functions no matter which implement is chosen Some of the functions such as area will of course depend on the related encoded values for the implement For some implements there are further functions e g the area functions These special functions will be dealt with under the implement in question Teglet 2 3 GENERAL FUNCTIONS TEEJET 5000 OPERATORS MANUAL TRACTOR FUNCTIONS SLIP Wheel slip PTO Revolutions from the PTO METRE Distance travelled BATT Battery voltage SLIP Wheelslip in per cent The relation between speed measured on a wheel or an axle and speed measur
215. h Manual start can e g be used in field corners where a run up is not possible 4 80 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL K RAMP EMPTY AUGER the auger is emptied when this key is pressed The auger will turn with 200 RPM when this key is held down The auger stops when the key is released Pressing the NEXT PAGE key displays the first available functions SPREADER ON OFF This key is used as the on off switch for the spreader It is also possible to start stop the spreader using an external switch This picture is displayed when spreading When the area override sensor is activated not I counting area I is displayed and all sections will disappear 4 81 FERTILISER DISTRIBUTOR RAMP TEEJET 5000 OPERATORS MANUAL LIME SPREADER ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements DOSE RATE The effective working width of the spreader must be encoded under DISTRIB WIDTH before
216. haft or from a sensor fitted on a wheel depending on the make and model of the tractor used RADAR If the tractor is fitted with radar then select RADAR and forward speed will be measured from the radar Radar and the number of pulses per metre will be displayed at the top of the screen IMPORTANT Working in crops that are blowing in the wind or working in areas with surface water can affect the accuracy of the radar we recommend using a speed sensor fitted to the tractor under these circumstances WHEEL IMPLEMENT If the implement is fitted with a speed sensor then press the WHEEL IMPLEMENT key The TeeJet 5000 will now use this sensor for forward speed measurement IMPLEMENT SENSOR The implement override sensor starts and stops area measurement The following options can be selected in OTHER IMPLEMENT 1 Lift 2 Implement 3 if a sensor is fitted METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor SENSOR WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor Telet 8 5 OTHER IMPLEMENT TEEJET 5000 OPERATORS MANUAL PTO SENSOR Encode the number of pulses per revolution for a PTO sensor if fitted If the TeeJet PTO sensor kit is fitted 932 983 encode 1 WARNINGS The following warnings can b
217. he first bout Thereafter the track number should be changed to 9 10 and tramlines are made when the actual track number is 2 4 7 and 9 Note where the bouts should be counted A and where bouts should not be counted all other corners in the first 3 bouts around the whole field Bout counting can be controlled by using either the HOLD key or by using the TRACK keys 3 i E zy E E EE I EE VN C 1 m 5 41 SEED DRILL LEMKEN TEEJET 5000 OPERATORS MANUAL METHOD D This method is used with a 4 or 6 metre seed drill making 18 or 27 metre tramlines The track number is set to 18 see track number page 5 55 Example of method D Right The seed drill is fitted with 2x2 magnetic valves on the right hand side of the machine and 2x2 magnetic valves fitted on the left hand side of the machine Drilling is started on the right hand side of the field as shown on the diagram with a track number of 1 18 Tramlines are made when the actual track number is 3 7 12 and 16 Note where the bouts should be counted A and where bouts should not be counted all other corners in the first
218. he machine and let it run at the recommended speed 5 Press the START key and the computer is ready for CALIBRATION TEST 1 6 Switch the main on off switch to ON The TeeJet 5000 will count seconds under the test To ensure accurate calibration use as much fertiliser as possible 7 When a suitable amount has been released switch the spreader off 8 Weigh the released fertiliser as accurately as possible remember to deduct the weight of the bucket Encode the amount with 1 decimal using the numerical keypad 9 Press the CALIB TEST 2 key and the computer is ready for calibration test 2 proceed as described for calibration test 1 steps 4 7 10 Press the CALC AND SAVE Key and it is possible to save the calibration result in 1 of 3 positions Select which position to save the result in using the arrow keys press thereafter the SELECT key If the CALCULATE key is pressed the calibration will be used until another calibration procedure takes place or another calibration previously saved is selected If the metered encoded amounts from the calibration procedure are not accurate enough for the TeeJet 5000 an warning will be given and the calibration procedure must be carried out again leefet 4 121 FERTILISER DISTRIBUTOR RAUCH AXERA TEEJET 5000 OPERATORS MANUAL If there are previously saved calibration results the procedure is as follows 1 Press the CALIB PROCED key and th
219. he return to the tank but the pump will still regulate When spreading recommences the application rate will be correct as the pump was regulating whilst the implement sensor was activ i e turning If INACTIVE is selected the pump must alter speed application rate from 0 each time the implement sensor has been activated The pump will not regulate whilst turning 7 38 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER HORSCH PWM Calibrating the proportional valve is necessary to protect the proportional valve against too much power This calibration is normally carried out by the engineer during fitting the equipment on the slurry spreader The procedure is however described below It is not recommended to carry out this calibration procedure without competent knowledge of power measuring The procedure is thus 1 Connect a meter in series between TeeJet 5000 OUT output Max 100mA Out1 12V 2 Pressing the and keys alters the PWM value and the power can be measured on the meter 3 When the power is 100 mA Must not exceed 100 mA press CALIB CALC and the procedure is finished 4 The PWM value will be the highest value that can be reached by regulation Teglet 7 39 SLURRY SPREADER HORSCH TEEJET 5000 OPERATORS MANUAL PROPORTIONAL VAVE Select which porportional valve is fitted on the system in this menu 1 Select type
220. he sprayer s open close function main open close function main on off switch or manual main on off switch or manual main valve valve TRAIL 8 Signal from filling flowmeter Signal from filling flowmeter Turn the paddle wheel by Turn the paddle wheel by hand or fill the sprayer hand or fill the sprayer TRAIL 15 Not used Not used TRAIL 16 Not used Not used BOM 1 12 Shows which of the Shows which of the encoded boom sections are encoded boom sections are open or closed open or closed TEST OUTPUT OUT 1 Signal that controls the Signal that controls the pressure and hence pressure and hence increases the application increases the application rate Pressure will increase rate Pressure will increase as long as the key is as long as the key is activated activated OUT 2 Signal that controls the Signal that controls the pressure and hence pressure and hence decreases the application decreases the application rate Pressure will decrease Pressure will decrease as long as the key is as long as the key is activated activated OUT 3 Not used Not used OUT 4 Signal to the fill alarm or Signal to the fill alarm or valve in conjunction with valve in conjunction with automatic fill flow automatic fill flow POT1 2 Not used Not used 2 22 Teglet 5000 OPERATORS MANUAL GENERAL FUNCTIONS TEST INPUT OUTPUT FERTILISER SPREADER
221. he spreader is imperative for correct operation of the automatic control function Great attention must therefore be paid to this calibration procedure CALIBRATION PROCEDURE 1 Fit the calibration equipment to the right hand side of the spreader 2 Fill the right hand hopper with approx 200 kg fertiliser 3 Run the PTO at 200 250 RPM 4 Press the CALIB PROCED key and the picture to the left is displayed 5 Press the START key and the spreaders handle opens automatically 6 The handle will open to 4 5 for the E and EX models and 3 5 for the D DZ models 7 After 30 seconds the handle will close and the amount released can be weighed 8 Encoded the amount released in RELEASED and press the END TEST key the spreader is calibrated 9 Remove the calibration equipment from the spreader NOTE The encoded amount released is saved when the END TEST key is pressed This calibration procedure should be carried out for each new batch of fertiliser and each time the fertiliser type is changed to ensure accurate operation leefet 4 29 FERTILISER DISTRIBUTOR BOGBALLE TEEJET 5000 OPERATORS MANUAL NOTE If after some time the amount spread is not the same as the amount calculated by the monitor check if the machine
222. her sections The main on off switch should be set to off NOTE calibration procedure can be done using both sections The optimal accuracy is achieved using both sections but an adequate accuracy can be achieved by measuring the amount of fertiliser from one section If you wish to calibrate using both sections then the TeeJet 5000 knows how many and which sections are open during the test The only difference therefore is that the fertiliser from all of the sections open must be captured and weighed during the calibration procedure 2 Open the hydraulic valve and move the main on off switch to on for a short time to fill the feed rollers 3 Empty the bucket and the fertiliser calibration procedure is now ready The TeeJet 5000 is now almost able to control the calibration procedure on its own Proceed as follows 1 Press the CALIB PROCED key and thereafter the NEW CALIB Key 2 Encode the 3 different application rates that are to be used in operation Press the CALIB PROCED key The top of the display shows the application rate to be calibrated The computer automatically sets the speed of the feed rollers to 10 of the required application rate 400 kg ha gt 40 RPM If however through experience you know that the speed of the feed rollers should be higher or lower for this particular application rate then the feed roller speed can be increased or decreased using the or keys
223. here END TIME is calculated from this encodement 4 54 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL HYDR B P VALVE CALIBRATION The proportional valve and the computer must be set up to work together the valve needs to be calibrated This calibration procedure must be carried out the first time the spreader is used and a few times thereafter i e at the start of each season Before calibration The hydraulic oil must be at its normal operating temperature before the calibration procedure is carried out Ensure that the spreader belts can run without hindrance IMPORTANT The tractor hydraulic system must not supply more than 70 Litres per minute Calibration 1 Press START with an empty spreader the hydraulic motor runs to full speed and falls slowly thereafter The actual belt speed is shown as RPM whilst the calibration procedure is carried out 2 Press OK when it appears on the display the calibration procedure is finished If the belt does reach the required speed in the defined time a warning will be given 4 55 FERTILISER DISTRIBUTOR BREDAL HYDR B TEEJET 5000 OPERATORS MANUAL AUTO MAN Select if the spreader is to be emptied at a standstill or at very low speeds For normal operation select AUTO AUTO is selected as the norm as this is applicable for most purposes Manual operation The rate in kg min
224. his figure if the system is used with other pulse weighing systems Manual calculated calibration figure This method is especially good for spreaders that control the application rate by controlling the speed of a feed roller that gives an exact amount per revolution The calibration figure is calculated as follows on such spreaders Volume per revolution x volume weight CALIBRATION FIGURE Pulses per revolution Encode the calculated figure as the calibration figure using the numerical keypad RPM 2 If neither WEIGHING OR PULSE WEIGHING are used then the shaft speed of axle no 2 can be monitored axle no 1 is always displayed Pressing the 2 key allows the numbers of pulses per revolution to be encoded 4 9 FERTILISER DISTRIBUTOR OTHER TEEJET 5000 OPERATORS MANUAL DISTRIBUTOR WIDTH The working width for the spreader If the spreader is fitted with individual sections then encode each section by itself starting from the left Otherwise encode the width as 1 section all other sections as 0 FORWARD SPEED SENSOR The TeeJet 5000 V 4 fertiliser distributor program Other type gives the option of choosing between 3 different speed sensors Wheel tractor Wheel spreader Radar WHEEL TRACTOR The speed signal can come from a sensor fitted in the gear box or on a drive shaft or from a sensor fitted on a wheel depending on the make and
225. ibed under ENCODE leefet 4 51 FERTILISER DISTRIBUTOR BREDAL HYDR B TEEJET 5000 OPERATORS MANUAL 1 Press TARRING for approx 3 seconds whilst at a standstill WEIGHT will change to 0 which is the same as 0 KG There are 2 possibilities A Start spreading with the weight displayed and at each weighing the amount left in the spreader can be seen B Each time TARRING is pressed for approx 3 seconds with something in the spreader the displayed KG will be O It is now possible to see how much has been used negative weighing It is not possible to see how much fertiliser is left in the spreader SPREADER ON OFF This key is used as the on off switch for the spreader It is also possible to start stop the spreader using an external switch This picture is displayed when spreading When the area override sensor is activated not I counting area 1 is displayed and all sections will disappear 4 52 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL HYDR B FERTILISER SPREADER ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements
226. ibration should take place when 1 If you suspect that the flow characteristics of the fertiliser have changed i e a new load 2 Change of weather temperature and moisture Even when the above factors have been taken into consideration fertiliser calibration should be checked at regular intervals 4 120 TEEJET 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH AXERA H FERTILISER CALIBRATION Prepare the spreader as follows before the fertiliser calibration procedure takes place 1 ease the calibration procedure it is only necessary to calibrate one section of the spreader Using the switch box open this one section and shut all of the other sections The main on off switch should be set to off NOTE calibration procedure can be done using both sections The optimal accuracy is achieved using both sections but an adequate accuracy can be achieved by measuring the amount of fertiliser from one section If both sections are used for calibration the total amount from both sides must be encoded Do not open any other sections during the calibration procedure 2 different fixed application rates used during operation must be encoded now Press thereafter the CALIB PROCED key 3 minimum and maximum forward speed at which the spreader will be operating must be encoded by moving the cursor and then using the numerical keypad Encodement range 3 0 30 0 KPH 4 Start t
227. ic valves on both sides of the seed drill Drilling is started on the left hand side of the field with the track number set to 1 26 as shown on the diagram After the first bout around the field change direction to drive the other way around the filed do this for the third and fourth bout also Tramlines are made when the present track number is 4 10 17 and 23 Note where tracks should be counted A and where tracks should not be counted all other corners in the first 4 bouts around the field Track counting can be controlled by using either the HOLD key or by using the TRACK keys lie a aaah dada Maa 1 26 2 26 3 26 4 26 5 26 6 26 7 26 8 26 9 26 10 26 11 26 12 26 13 26 14 26 15 26 16 26 17 26 18 26 19 26 20 26 21 26 22 26 23 26 24 26 25 26 26 26 1 26 2 26 Az 1 5 51 SEED DRILL LEMKEN TEEJET 5000 OPERATORS MANUAL SEED DRILL ENCODEMENT This menu allows the operator to encode the various settings that are necessary for sowing Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements
228. ing is wanted D SHAFT Warning ON OFF if the drill shaft stops turning HOPPER Warning ON OFF for empty seed hopper RPM Warning ON OFF and MIN MAX limits for fan RPM NB If the warning for RPM is on then the computer will not allow sowing to commence before it receives signals from the fitted RPM sensor If the warning is off then sowing is independent of the RPM sensor WARN DOSE AREA The dose rate warning is a fixed warning which cannot be switched off As the program is used for a number of different seed drills used under various working conditions it is possible to set the warning so that unwanted warnings are not given This is done under the main menu for the Lemken seed drill program 5 56 5000 OPERATORS MANUAL SEED DRILL LEMKEN Pressing the HOLD key for 5 seconds when this display is shown see page 5 32 allows for programming an application rate alarm Encode the percentile deviation that is allowed before the warning is given standard 5 Time Encode the number of seconds that the above deviation is allowed before the warning is given standard 20 seconds RPM Encode the minimum RPM for the motor that drives the drill shaft The minimum RPM is used amongst others to calculate the forward speed limits given during a seed calibration standard value for newer machines no gearbox 150 RPM for older machines with gearbox
229. ions The optimal accuracy is achieved using both sections but an adequate accuracy can be achieved by measuring the amount of fertiliser from one section If both sections are used for calibration the total amount from both sides must be encoded Do not open any other sections during the calibration procedure 2 Three different fixed application rates used during operation must be encoded now Press thereafter the CALIB PROCED key 3 The minimum and maximum forward speed at which the spreader will be operating must be encoded by moving the cursor and then using the numerical keypad Encodement range 3 0 30 0 KPH 4 Start the machine and let it run at the recommended speed 5 Press the START key and the computer is ready for CALIBRATION TEST 1 6 Switch the main on off switch to ON The TeeJet 5000 will count seconds under the test To ensure accurate calibration use as much fertiliser as possible 7 When a suitable amount has been released switch the spreader off 8 Weigh the released fertiliser as accurately as possible remember to deduct the weight of the bucket Encode the amount with 1 decimal using the numerical keypad 9 Press the CALIB TEST 2 key and the computer is ready for calibration test 2 proceed as described for calibration test 1 steps 4 7 10 Press the CALC AND SAVE Key and it is possible to save the calibration result in 1 of 3 positions Select which position to save th
230. ions will be described one by one 5 32 leefet 5000 OPERATORS MANUAL SEED DRILL LEMKEN FIXED FUNCTIONS TRAMLINE CONTROL The primary function for seed drills is the track number The following picture is displayed S RACK NO Bout number Track number The bout number is the present bout being driven in the field counts 1 each time the drill is lifted The track number is what has been encoded see ENCODE The TeeJet 5000 has 2 different methods of controlling the tramlines A and B The method is selected under ENCODE TRAMLINE INDICATION The second fixed function indicates on the display whether tramlines are being made or not Tramlines are not being made Tramlines are being made KG HA The third function is the seed rate The seed rate is displayed in KG HA seed rate Two arrows are displayed to the left of the display These arrows indicate whether the computer is adjusting the seed rate up or down Correct operation presupposes 1 Correct calibration 2 That the correct wheel circumference and working width has been encoded 5 33 SEED DRILL LEMKEN HOLD KEY TEEJET 5000 OPERATORS MANUAL Press if the present bout is not required in the selected rhythm This function holds the present status regardless of how many times the drill is raised When this function is activated HOLD flashes on the display SELECTABLE
231. is figure if the system is to be used with other weigh cells in the future NOTE The weigh cell calibration should be checked at regular intervals STEP Encode the size of the steps for the STEP function This value is the same for both and The maximum step size is 9996 4 57 FERTILISER DISTRIBUTOR BREDAL HYDR B TEEJET 5000 OPERATORS MANUAL FORWARD SPEED SENSOR A speed sensor is fitted to the spreader this sensor gives the correct number of pulses for controlling the application rate and this sensor should be selected WHEEL TRACTOR AND RADAR If forward speed measurement is not required from the sensor mounted on the spreader WHEEL TRACTOR or RADAR can be selected Please refer to chapter 2 for speed sensor calibration METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor SENSOR WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor REVS SENSOR Encode the number of pulses per revolution for the individual sensors PTO SENSOR If the TeeJet PTO sensor kit is used 932 983 encode 1 RPM 1 SENSOR Bredal kit is supplied with sensor fitted for disc speed the number of pulses per revolution should be set to 1
232. is activated on tracks 5 amp 6 Note where tracks should be counted A and where tracks should not be counted all other corners in the first 4 bouts around the field Track counting can be controlled by using either the HOLD key or by using the TRACK keys E gt M 5 48 5000 OPERATORS MANUAL SEED DRILL LEMKEN Example of method G Left The seed drill is fitted with 2x2 magnetic valves on the left hand side of the seed drill and 1 magnetic valve on the right hand side of the seed drill Drilling is started on the left hand side of the field with the track number set to 1 10 as shown on the diagram After the first bout around the field change direction to drive the other way around the filed do this for the third and fourth bout also Tramlines are made when the present track number is 2 5 6 and 9 Only one magnetic valve is activated on tracks 5 amp 6 Note where tracks should be counted A and where tracks should not be counted all other corners in the first 4 bouts around the field Track counting can be controlled by using either the HOLD key or by using the TRACK keys 5 49 SEED DRILL LEMKEN TEEJET 5000 OPERATORS MANUAL
233. is an example of a complete kit for automatic application control 01 90 6 The automatic application control kits for fertiliser distributors do not use the 7 breakaway plug but use the system B plug amp RS bi 12 18 Teglet 5000 OPERATORS MANUAL FITTING INSTRUCTIONS SEED DRILL SEED DRILL SENSOR WIRE COLOUR PIN NUMBER RPM SENSOR ON THE BLUE DRILL SHAFT 2 CORE BROWN RPM SENSOR ON THE DRILL SHAFT 3 CORE RPM SENSOR ON CLUTCH EMPTY HOPPER LEVEL SENSOR IMPLEMENT SENSOR Tramline control cannot be connected directly to the breakaway plug The TeeJet 5000 fitting kit for seed drill must be used If tramline control is required the fitting kit displayed below should be used This kit is also prepared for additions 1 TeeJet 5000 seed drill kit Includes junction TeeJet no 921 180 box and breakaway plug with cable 2 RPM sensor for the drill shaft 2 core TeeJet no 905 152 3 Empty hopper level sensor TeeJet no 904 152 4 Implement sensor TeeJet no 930 982 Clutch kits with RPM sensors must be ordered to fit the drill shaft on the seed drill 5 Clutch kit for 17 mm hex axle TeeJet no 903 152 5 Clutch kit for 20 mm round axle TeeJet no 906 152 Teglet 12 19 FITTING INSTRUCTIONS TEEJET 5000 OPERATORS MANUAL BALER SENSOR WIRECOLOUR PINNUMBER BALE COUNTER SENSOR Blue 4
234. is empty press TANK EMPTY The value encoded under TANK VOLUME will be automatically transferred to TON M3 LEFT DAILY USE OF THE SLURRY PROGRAM WITHOUT A FLOWMETER Once all of the encodements have been accepted proceed as follows Start spreading and each time the area override sensor is activated implement sensor the following warning is displayed When this screen is displayed you have the following options If the machine is turning at the headland then continue driving and the warning screen will disappear when spreading starts again If you stop spreading temporarily without the tank being empty press PAUSE to remove the warning The warning screen will disappear when spreading starts again If the tank is empty press TANK EMPTY The following 2 things will happen automatically TANK VOLUME is transferred to TON M3 counter TANK VOLUME is added to the total counter for consumed amount which can be found in DATA DELETE 7 46 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER ZUNHAMMER CALCULATING M3 HA OR TON HA Each time EMPTY TANK is pressed the TeeJet 5000 calculates the amount spread with this tank full This makes it possible to find the correct forward speed PTO RPM and therefore the application rate for the last 1 2 loads An accurate
235. is menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warning ON OFF and MAX MIN limits for wheel slip in MIS DOSERATE Warning ON OFF and max difference in RPM 1 Warning ON OFF and MAX MIN limits for shaft speed Encode in RPM NB The encoded limits must exceed the limits encoded If a warning is required when an axle stops 0 RPM then set the minimum limit to 1 DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY 7 12 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER OTHER TYPE Teglet 7 13 SLURRY SPREADER OTHER TEEJET 5000 OPERATORS MANUAL 7 14 Teglet Slurry Spreader Hydraulic control DOSE RAI cmm ee 7 21 vali er 7 21 TANK VOLUME eee 7 21 FILLED VOLUME 7 22 Mice 7 22 FLOW FIGURE aho Qiii 7 22 e 7 23 DRIVE FACTOR 7 23 RETURN M 7 23 FORWARD SPEED SENSOR 7 24 WHEEL TRAG TOR T ee 7 2
236. is pressed the following is displayed AUTO MAN Select between automatic or manual operation Increased application Decreased application Teejet 7 19 SLURRY SPREADER OTHER TYPE HYDR TEEJET 5000 OPERATORS MANUAL Select between automatic or manual operation If manual operation is selected MAN will flash in the lower part of the display and will also appear as function keys Is only displayed if manual operation is selected Increase application When this key is pressed the application rate is increased The speed at which the rate increases depends on the speed of the regulating system Is only displayed if manual operation is selected Decrease application When this key is pressed the application rate is decreased The speed at which the rate decreases depends on the speed of the regulating system Pressing the PAGE key displays the first available functions MANUAL BOOM SECTION CONTROL It is possible to work with up to 9 individual boom sections presupposes encodement of the sections under DISTRIB WIDTH in encode These boom sections can be opened closed manually with the numerical keypad When the numerical key that corresponds to the boom section is pressed for approx 3 seconds the boom section is opened or closed If the spreader has 5 boom sections giving a total working width of 16 metres the boom sections can be encoded a
237. isplayed on the screen WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor METRE SWITCH Select whether the distance counter is started stopped manually via the function key in the operation menu or by the selected implement sensor 4 20 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR OTHER WITH REG SYSTEM PLUG There are 2 system plugs on the back of the TeeJet 5000 The System A plug is compatible with o der TeeJet 5000 versions The System B plug is for new connections ACTIVE 0 VOLT _ The individual sections are opened with OV 12 VOLT The individual sections are opened with 12V ON OFF ON The system B plug is used OFF The system B plug is not used WARNING ENCODE The following warnings can be set in this menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warning ON OFF MAX MIN limits for wheel slip in MIS DOSERATE Warning ON OFF and MAX difference in KG LEFT Warning ON OFF and amount of Kg min at which warning is wanted RPM 1 Warning ON OFF and MAX MIN limits for shaft speed Encode in RPM NB The encoded limits must exceed the limits encoded If a warning is required when an axle stops 0 RPM
238. lays the following Telet 6 5 BALER TEEJET 5000 OPERATORS MANUAL Method Without anything on the weighing system press TARRING Place a known weight on the weighing system the weight must be at least half of the weighing capacity of the system the more the better Using the arrow keys move the cursor to CALIB WEIGHT and encode the weight in KG using the numerical keypad Press the flashing LOAD FIG key calculated load figure is displayed at the top of the screen note this figure in case the value is deleted by mistake If no weighing system is fitted it is possible to see the shaft speed of an axle RPM 3 Regardless of which of these 2 functions has been selected it will always be displayed as one of the 2 fixed functions under OPERATION FORWARD SPEED SENSOR The TeeJet 5000 V 4 baler program gives the option of choosing between 2 different speed sensors Wheel tractor Radar WHEEL TRACTOR The speed signal can come from a sensor fitted in the gear box or on a drive shaft or from a sensor fitted on a wheel depending on the make and model of the tractor used for baling RADAR If the tractor is fitted with radar then select RADAR and forward speed will be measured from the radar Radar and the number of pulses per metre will be displayed at the top of the screen Please refer to chapt
239. le to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 5 62 5000 OPERATORS MANUAL SEED DRILL SIMBA SEED DRILL OPERATION KG The amount sown in KG KG LEFT The amount in KG of seed left in the hopper KG HA Seed rate in KG HA KG The amount sown in KG measured by a sensor fitted on the drill shaft Calibrating the system is necessary to ensure correct operation and this is done under ENCODE KG LEFT The amount in KG of seed left in the hopper the amount filled in must be encoded before work commences KG HA Seed rate in KG HA Pressing the NEXT PAGE key displays the next available functions D SHAFT Drill shaft speed TRACK 1 Moves one step forward in the tramline rhythm 4 Moves one step backwards in gt tramline rhythm HAHA gt gt IT Revolutions minute for both drill shafts TRACK 1 Moves one step forward in the tramline rhythm TRACK 1 Moves one step backwards in the tramline rhythm Pressing the NEXT PAGE key displays the next available functions
240. lect RPM and encode 1 pulse per rev if a pneumatic seed drill is being used For traditional seed drills fitted with tramline clutches select CLUTCH SENSOR the number of pulses per rev is normally 12 5 28 leefet 5000 OPERATORS MANUAL SEED DRILL NORSTEN example WARNINGS The following warnings are fixed warnings they cannot be switched off WARN DOSE AREA Check to see if the drill shaft motor has stopped when this warning is given Reasons Foreign bodies are stopping the drill shaft The encoded seed rate is outside of the regulating area The battery power is too low To avoid bare patches in the field it is necessary to raise the drill and back to the place at which sowing stopped leefet 5 29 SEED DRILL NORDSTEN TEEJET 5000 OPERATORS MANUAL WARN WHEEL DRILL All other alarms require the wheel sensor to be generating pulses To avoid large bare patches should the wheel sensor be damaged and therefore the computer receives no pulses even if the drill is lowered the warning WHEEL DRILL will be given after approx 15 seconds The warning is automatically removed when the computer receives pulses from the wheel sensor or when the seed drill is raised Pressing the OK key will remov
241. led before leaving encode HA LEFT Encode the size of the field to be spread here END TIME is calculated from this encodement FLOW FIGURE CALIBRATION NOTE Encode a start value of 1000 Automatic calibration 1 Fill the slurry spreader to the top so that you know the exact amount 2 Encode the amount in FILLED VOLUME 3 Empty the tank completely but be sure to stop emptying as soon as the tank is empty as air going through the flowmeter can cause false readings 4 Encode 0 00 using the numerical keypad under TANK REM VOL 5 Press the flashing CALC FLOW key 6 The flow figure is calculated NOTE Greater accuracy can be achieved by weighing the loads A new flow figure is calculated each time CALC FLOW is pressed 7 22 Teglet TEEJET 5000 OPERATORS MANUAL SLURRY SPREADER OTHER TYPE HYDR Manual calibration The flow figure can also be calculated manually as follows Fill the slurry spreader to the top so that you know the exact amount Reset the amount counter DATA DELETE Empty the tank completely Read the amount in DATA DELETE Place the value in the following formula Old flow figure x the amount spread NEW FLOW FIGURE amount read in Data delete TeeJet 5000 6 Encode this new flow figure using the numerical keypad DISTRIBUTOR WIDTH The working width of
242. libration The flow figure can also be calculated manually as follows 1 ney Fill the slurry spreader to the top so that you know the exact amount Reset the amount counter DATA DELETE Empty the tank completely Read the amount in DATA DELETE Place the value in the following formula Old flow figure x the amount spread NEW FLOW FIGURE The amount read in Data delete TeeJet 5000 6 Encode this new flow figure using the numerical keypad BOOM WIDTH The working width of the spreader If the system is fitted with control valves for each section then the individual section width must be encoded here left boom section 1 If the spreader does not have individual sections then encode the whole spreader width as section 1 all other sections must be encoded as 0 UNIFORM PRESSURE If the distribution head is fitted with uniform pressure valves return to tank or not ON YES OFF NO Teglet 7 35 SLURRY SPREADER HORSCH TEEJET 5000 OPERATORS MANUAL FORWARD SPEED SENSOR The TeeJet 5000 V 4 slurry spreader program gives the option of choosing between 3 different speed sensors Wheel tractor Wheel spreader Radar WHEEL TRACTOR The speed signal can come from a sensor fitted in the gear box or on a drive shaft or from a sensor fitted on a wheel depending on the make and model of the tractor used for slurry spreading RADAR If the tractor is fitted with
243. lication rate can also be encoded in the SPRAYER OPERATION screen STEP Encode the size of the steps for the STEP function This value is the same for both and The maximum step size is 99 LITRE LEFT To see how much is left in the tank the amount filled must be encoded here If there is some liquid left in the tank before filling then this amount must be added to the amount filled thus Amount left in tank filled amount Litre left NOTE LITRE LEFT is calculated automatically if a filling flowmeter is fitted Teefet 3 9 SPRAYER TEEJET 5000 OPERATORS MANUAL HA LEFT Encode the size of the field to be sprayed here END TIME REST DOS REST METRE and FILL VOLUME are calculated from this encodement FLOW FIGURE This figure is the calibration figure for the flowmeter For normal flowmeters 20 200 l min encode a value of 2000 See the recommend flow figure for other flowmeters CALIBRATION Use a start value of 2000 as the flow figure Method 1 automatic 1 Fill the sprayer with min 600 litre the more the better 2 Encode the filled amount in LITRE LEFT 3 Spray a minimum of 500 litre spray with all boom sections open in the normal pressure range Read the amount left in the tank using the sight gauge on the sprayer Encode the above amount left in the tank in LIT Press the flashing FLOW key The new flow figure has now been calculate
244. m the sensor during spreader calibration When the calibration is finished the amount released is weighed and encoded the computer can now calculate the amount released per pulse Procedure Prepare the spreader for calibration 1 The picture to the left is displayed when CALIB PROCED has been selected 2 NO OF PULSES must be 0 before the calibration procedure is continued If the number is higher then press the RETURN key and select CALIB PROCED again 3 Pressing the RPM 2 key allows you to adjust the speed of the motor that drives the regulating device pressing the key increases the chain speed pressing reduces the chain speed The speed of the floor chain is displayed 4 Set chain speed to 0 using the key when suitable amount has been released and press OK Move the cursor to WEIGHT and encoded the amount released using the numerical keys NOTE The pulse counter must have counted a number of pulses 5 Press the flashing Key and the calibration procedure is finished The CAL FIG which is displayed at the top of the screen can be noted Manual calibration The CAL FIG Can be calculated manually as follows Volume per revolution x volume weight CALIBRATION FIGURE Pulses per revolution 4 18 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR OTHER TYPE WITH REG NOTE If after s
245. me TANK EMPTY is pressed the tank size is transferred to TON M3 REST and the slurry spreader is ready to fill and spread again This function is also used in conjunction with flowmeter calibration see page number 7 48 TON M3 MIN The amount of slurry per minute going through the flowmeter Pressing NEXT PAGE displays the next possible functions XX Step dosage increase XX Step dosage decrease NORMAL Return to the required normal application rate DOSE RATE Encoding the required application rate XX Percentile increase of the encoded application rate The size of the steps is altered in encode XX Percentile reduction of the encoded application rate The size of the steps is altered in encode NORMAL Only displayed if the step feature has been used Normal application rate Regardless of how many steps the application rate has been increased decreased by pressing this key will return the application rate to normal DOSE RATE Pressing this key allows the application rate to be altered directly from the operation screen see also DOSE RATE in encode Pressing the NEXT PAGE key displays the next functions RPM 1 Revolutions per minute RPM 1 The shaft speed of an axle is displayed here Normally the RPM of the distributor macerator Pressing the NEXT PAGE key displays the first set of functions
246. mount Ton left HA LEFT Encode the size of the field to be spread here END TIME is calculated from this encodement leefet 4 83 FERTILISER DISTRIBUTOR BREDAL RAMP TEEJET 5000 OPERATORS MANUAL P VALVE CALIBRATION The proportional valves and the computer must be set up to work together the valves need to be calibrated This calibration procedure must be carried out the first time the spreader is used and a few times thereafter i e at the start of each season Before calibration The hydraulic oil must be at its normal operating temperature before the calibration procedure is carried out Ensure that the spreader belts can run without hindrance The auger should be full before calibration to avoid vibration IMPORTANT The tractor hydraulic system must not supply more than 70 Litres per minute Calibration 1 Press CALIB BELT with an empty spreader the hydraulic motor runs to full speed and falls slowly thereafter The speed of the hydraulic motor is shown on the display during calibration A warning will be given if the belt does not reach the required speed within the required time 2 Press OK when it appears on the display the calibration procedure is finished 3 Press CALIB BELT with an empty spreader the hydraulic motor runs to full speed and falls slowly thereafter
247. mputer must be set up to work together the valve needs to be calibrated This calibration procedure must be carried out the first time the spreader is used and a few times thereafter i e at the start of each season Before calibration The hydraulic oil must be at its normal operating temperature before the calibration procedure is carried out Ensure that the spreader belts can run without hindrance IMPORTANT The tractor hydraulic system must not supply more than 70 Litres per minute Calibration 1 Press START with an empty spreader the hydraulic motor runs to full speed and falls slowly thereafter The actual belt speed is shown as RPM whilst the calibration procedure is carried out 2 Press OK when it appears on the display the calibration procedure is finished If the belt does reach the required speed in the defined time a warning will be given 4 69 FERTILISER DISTRIBUTOR BREDAL HYDR K TEEJET 5000 OPERATORS MANUAL AUTO MAN Select if the spreader is to be emptied at a standstill at very low speeds For normal operation select AUTO AUTO is selected as the norm as this is applicable for most purposes Manual operation The rate in kg min must be encoded when MAN has been selected Encode the required kg min using the numerical keypad Pressing CALC CALIB Calculates the correct setti
248. must be encoded when MAN has been selected Encode the required kg min using the numerical keypad Pressing CALC CALIB Calculates the correct settings for the spreader DISTRIBUTOR WIDTH The effective spreading width of the spreader Method 1 Press the DISTRIB WIDTH key and the picture to the left is displayed 2 Encode the effective spreading width in centimetres using the numerical keypad 4 56 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL HYDR B WEIGHING If the spreader is equipped with weigh cells then set weighing to ON otherwise set this to OFF WEIGHING ON If this function is required then the weighing system must be calibrated this is done as follows 1 Press the CALIB CALC key and the picture to the left is displayed 2 With an empty spreader press the TARRING key to zero set the weigh cells 3 Fill the spreader with an exact known amount The weight should be as large as possible but must be minimum 50 of the spreaders capacity Using the arrow keys move the cursor to CALIB WEIGHT and encode the amount filled with the numerical keypad 4 Press the flashing CALC LOAD FIG key The system has now been calibrated The calculated figure is displayed at the top of the screen note th
249. n must be used if the distance driven per pulse is greater than 100 cm fitting more magnets to the wheel may solve this problem and allow the automatic calibration procedure to be used WHEEL IMPLEMENT Certain implements are fitted with a speed sensor that give a correct number of pulses for automatic application with the TeeJet 5000 This sensor should be used if mentioned in the chapter concerning the implement in question Calibrating the wheel implement sensor is almost the same as described for wheel tractor RADAR If the tractor is fitted with radar then select and forward speed will be measured from the radar Radar and the number of pulses per metre will be displayed at the top of the screen The number of pulses per metre will vary from radar to radar typical figures are 100 or 130 The angle at which the radar is fitted in relation to the ground will affect the number of pulses per metre we recommend using the automatic calibration procedure which is described in the following for wheel tractor IMPORTANT Working in crops that are blowing in the wind or working in areas with surface water can affect the accuracy of the radar we recommend using a speed sensor fitted to the tractor under these circumstances GENERAL FUNCTIONS TEEJET 5000 OPERATORS MANUAL MANUAL CALIBRATION 1 Mark the wheel and the ground 2 Drive exactly 10 rotations of the wheel remember to count rotations on the wheel fitt
250. nd MAX MIN limits for speed SLIP Warning ON OFF MAX MIN limits for wheel slip in TON LEFT Warning ON OFF and amount of kg min at which warning is wanted NB The encoded limits must exceed the limits encoded If a warning is required when an axle stops 0 RPM then set the minimum limit to 1 DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY OFFSET 1 Press and hold this key for approx 5 seconds before the selected spreader is accepted 2 Encode the required offset value using the numeric keypad leefet 4 87 FERTILISER DISTRIBUTOR BREDAL RAMP TEEJET 5000 OPERATORS MANUAL 4 88 Fertiliser distributor Rauch Aero RAUCH AERO FERTILISER DISTRIBUT OR crece rnnt sniper pne 4 90 FERTILISER DISTRIBUTOR OPERATION essen enne 4 91 FERTILISER SPREADER FUNG TIONS te 4 91 1 AUTOMATIC APPLICATION 22 4 92 2 MANUAL APPLICATION CONT ROE lt cee cen 4 94 FERTILISER DISTRIBUTOR ENCODE 4 95 WORKING WID LR eU 4 96 PORVWARD SPEED SEIN GOR e Eran eee 4 96 WHEEL TRACTOR QD 4 96 WHEEL SPREADER de 4 96 bis lle ii 4 96 FERTILISER
251. ng ON OFF and MAX MIN limits for wheel slip in MIS DOSE Warning ON OFF and MAX deviation in LITRE LEFT Warning ON OFF and amount of litres min at which warning is wanted WORK PRESS Warning ON OFF and MAX MIN limits for the working pressure of the sprayer NB It is recommended to turn all warnings which are not wanted OFF DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY Teglet 3 13 SPRAYER TEEJET 5000 OPERATORS MANUAL 3 14 Fertiliser distributor FERTILISER DISTRIBUTOR OTHER TYPE acini eene cnc 4 1 FERTILISER DISTRIBUTOR OTHER WITH 4 13 FERTILISER DISTRIBUTOR BOGBALLE D DZ amp 4 23 FERTILISER DISTRIBUTOR BREDAL B2 B4 amp 4 35 FERTILISER DISTRIBUTOR BREDAL HYDR 4 47 FERTILISER DISTRIBUTOR BREDAL HYDR 4 61 FERTILISER DISTRIBUTOR BREDAL K 4 75 FERTILISER DISTRIBUTOR RAUCH 4 89 FERTILISER DISTRIBUTOR RAUCH 4 101 FERTILISER DISTRIBUTOR RAUCH 4 113 FERTILISER DISTRIBUTOR REIP 4 125 Fertiliser distributor Other Type FERTILISE
252. ngs for the spreader DISTRIBUTOR WIDTH The effective spreading width of the spreader Method 1 Press the DISTRIB WIDTH key and the picture to the left is displayed 2 Encode the effective spreading width in centimetres using the numerical keypad 4 70 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL HYDR WEIGHING If the spreader is equipped with weigh cells then set weighing to ON otherwise set this to OFF WEIGHING ON If this function is required then the weighing system must be calibrated this is done as follows 1 Press the CALIB CALC key and the picture to the left is displayed 2 With an empty spreader press the TARRING key to zero set the weigh cells 3 Fill the spreader with an exact known amount The weight should be as large as possible but must be minimum 50 of the spreaders capacity Using the arrow keys move the cursor to CALIB WEIGHT and encode the amount filled with the numerical keypad 4 Press the flashing CALC LOAD FIG key The system has now been calibrated The calculated figure is displayed at the top of the screen note this figure if the system is to be used with other weigh cells in the future NOTE The weigh cell calibration should be checked at regular intervals STE
253. nsors Teglet 7 25 SLURRY SPREADER OTHER TYPE HYDR TEEJET 5000 OPERATORS MANUAL WARNING ENCODE The following warnings can be set in this menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warning ON OFF and MAX MIN limits for wheel slip in MIS DOSERATE Warning ON OFF and max difference in 96 RPM DISTRIBUTOR Warning ON OFF and MAX MIN limits for shaft speed Encode in RPM RPM PUMP Warning ON OFF and MAX MIN limits for shaft speed Encode in RPM NB The encoded limits must exceed the limits encoded If a warning is required when an axle stops 0 RPM then set the minimum limit to 1 DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY 7 26 Teglet Slurry spreader Horsch SLURRY SPREADER 7 28 SLURRY SPREADER OPERATION HORSQOCH 7 29 SLURRY SPREADER FUNCTIONS WITH FLOW 7 29 SLURRY SPREADER WITHOUT 7 31 SLURRY SPREADER ENCODE ERR 7 33 Being i
254. nts Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements DOSE RATE The required application rate is encoded in KG HA KG LEFT The amount filled into the hopper must be encoded here to be able to see how much fertiliser is left in the hopper NOTE If there is some fertiliser left in the hopper before refilling then this amount must be added to the amount filled thus Amount left in hopper filled amount Kg Left HA LEFT Encode the size of the field to be spread here END TIME is calculated from this encodement leefet 4 17 FERTILISER DISTRIBUTOR OTHER WITH REG TEEJET 5000 OPERATORS MANUAL CALIBRATION Particular attention must be paid to the calibration procedure as this is the basis for correct operation The amount is measured via a pulse generator mounted on the sow axle The system must be calibrated to ensure correct operation There are 2 methods available to find the calibration figure an automatic method and a manual method Automatic calibration This calibration procedure is carried out at the same time as the normal spreader calibration The principle works by counting the number of pulses given fro
255. o the left is displayed 2 Encode the effective spreading width in centimetres using the numerical keypad STEP Encode the size of the steps for the STEP function This 96 value is the same for both and The maximum step size is 9996 FORWARD SPEED SENSOR A speed sensor is fitted to the spreader this sensor gives the correct number of pulses for controlling the application rate and this sensor should be selected WHEEL TRACTOR AND RADAR If forward speed measurement is not required from the sensor mounted on the spreader WHEEL TRACTOR or RADAR can be selected Please refer to chapter 2 for speed sensor calibration METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor SENSOR 4 86 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL RAMP WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor REVS SENSOR Encode the number of pulses per revolution the PTO sensor sends per revolution If the TeeJet PTO sensor kit is used 932 983 encode 1 WARNING ENCODE The following warnings can be set in this menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF a
256. ome time it is found that the total amount spread is not the same as the computer has calculated check the machine s settings that the calibration and encodements are correct If all the encodements are correct the following can be done If the fertiliser being used has been stored for a long time or is damper or drier than normal then these conditions can vary from the time of calibration to the present This can be changed by altering the encoded calculated CAL FIG by the amount in percent that the present application varies from the required application Lower CAL FIG higher application DISTRIBUTOR WIDTH The working width for the spreader used Each spreader section is encoded individually in centimetres section 1 is the left hand side of the machine NOTE All unused sections must be encoded as 0 The total working width can be seen at the bottom of the display whilst encoding STEP Encode the size of the steps for the STEP function This value is the same for both and The maximum step size is 99 DRIVE FACTOR The speed at which the regulating system adjusts to the correct position Min 1 and Max 500 Normal 100 If the regulation system adjusts to the correct application rate too slowly then the drive factor should be increased If the system is constantly searching up amp down for the correct application rate then reduce the drive factor UNIFORM PRESSURE Only used if the spread
257. ontact your local dealer if further support is needed Regarding responsibility for use of the product we refer to our sales and delivery terms especially paragraph 7 which follows ds Product usage 7 1 Any use of the product is at the sole risk of the buyer buyer is therefore not entitled to any form for compensation caused by for example any of the following Disturbance to from any electronic services or products that not confirm to the standards for CE marking x Missing or poor signal coverage or a succession hereof from external transmitters receivers used by the buyer Functional faults which apply to or from a PC program or PC equipment not delivered by the seller Faults that may arise from the buyers negligence to react to warnings and fault messages from the product or which can be traced to negligence and or absent constant control of the work carried out in comparison to the planned job 7 2 When implementing new equipment the buyer must take great care pay attention Any doubts as to correct operation use should result in contacting the sellers service department This manual may not be altered copied or manipulated in any way Unoriginal manuals can lead to operational faults damaging machines or crops as a consequence thereof TeeJet Technologies can therefore not be held responsible for damages incurred which can be traced to the use of unoriginal or mani
258. or type 7 Accept type It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one 4 126 Teefet 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR REIfI FERTILISER DISTRIBUTOR OPERATION REIBL FORWARD SPEED The primary function under fertiliser distributor is forward speed Forward speed is displayed in KPH with 1 decimal Forward speed is calculated from the signal from the speed sensor selected in encode wheel tractor wheel spreader or radar APPLICATION RATE IN TON HA The present application rate in Ton ha Calculated from the number of pulses from the floor chain and area measurement speed and working width It is therefore necessary to drive and spread at the same time to get a reading for this function NOTE Correct calibration of forward speed and weight per pulse plus correctly entered working width are essential for accurate operation FERTILISER DISTRIBUTOR FUNCTIONS XX Step dosage Increase Step dosage Reduction DOSE RATE NORMAL Encoding the required application rate or return to normal after using the step key
259. orward speed Forward speed is displayed in KPH with 1 decimal Forward speed is calculated from the signal from the speed sensor selected in encode wheel tractor wheel sprayer or radar SPREADER SECTION INDICATION The picture to the left shows a 2 section spreader with 1 section closed and 1 section open The number of sections can be changed in ENCODE The figure to the right indicates which calibration is being used REQUIRED APPLICATION RATE The second function is the required application rate If there is a difference between the right and the left hand side this will also be displayed An arrow is displayed on the left of the screen indicating which way the regulating device is moving NOTE Different application rates for the two sides can only be achieved via the keys When the area override sensor is activated not I counting area I is displayed and all sections will disappear FERTILISER SPREADER FUNCTIONS There are 2 different function sets in this menu The o displayed set depends on whether automatic or manual application control has been selected The following describes each function set individually 4 103 FERTILISER DISTRIBUTOR RAUCH BETA DELTA TEEJET 5000 OPERATORS MANUAL 1 AUTOMATIC APPLICATION CONTROL KG HA1 KG HA2 These 3 application rates are set in ENCODE can
260. ositions Select which position to save the calibration in using the arrow keys press thereafter the SELECT key If the CALCULATE key is pressed the calibration will be used until another calibration procedure takes place or another calibration previously saved is selected If however through experience you know that the calculated amount released per pulse is incorrect then press CANCEL and a new calibration test must be carried out The calibration procedure relates closely to the encoded working width The computer will give a warning if the working width is changed without re calibrating the spreader If there are previously saved calibration results the procedure is as follows 4 98 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH AERO 1 Press the CALIB PROCED key and the TeeJet5000 displays the picture to the left It is possible to page through the saved calibration results using the NEXT PAGE key 2 Pressing the ACCEPT key uses the selected calibration STEP Encode the size of the steps for the STEP function This value is the same for both and The maximum step size is 9996 KG LEFT The amount filled into the spreader must be encoded here to be able to see how much fertiliser is left in the hopper NOTE If there is some fertiliser left in the hopper before refilling
261. ous screen PRINTING TASKS VIA A PC To transfer and print tasks to a PC the follow items are required TeeJet 5000 PC interface incl Power supply TeeJet stock number 905 168 PC with Windows 3 xx or Windows 95 98 operating software Office printer Windows has 2 programs that you can use for transfer and printing tasks Write or Word pad are word processing programs that come with Windows 3 xx or Windows 95 98 Terminal or Hyper Terminal are communication programs that can amongst other things be used to import text files via the PC s serial port Other similar Windows programs can of course be used if this is desirable CONNECTION OF THE TEEJET 5000 TO THE PC The TeeJet 5000 PC interface consists of a special serial cable a 9 to 25 pin adapter and a transformer to connect to the mains power supply The adapter that changes the 9 pin plug to a 25 pin plug is used when the PC has a 25 pin serial port Connect one end of the PC Interface to the flying lead on the TeeJet 5000 and the other end to the serial port being used on the PC Connect the transformer to the mains power supply 2 10 Teglet 5000 OPERATORS MANUAL GENERAL FUNCTIONS SETTING TERMINAL UP Double click on the Terminal icon You can find the program icons in various places depending on the way that Windows has been set up Refer to the Windows operator manu
262. portional Signal to open the proportional valve completely When the key valve completely When the key is released the valve shuts is released the valve shuts OUT 2 Not used Not used OUT 3 Not used Not used OUT 4 Not used Not used POT1 2 9 used Not used Teglet 2 31 GENERAL FUNCTIONS TEEJET 5000 OPERATORS MANUAL TEST INPUT OUTPUT OTHER IMPLEMENT TEST INPUT OTHER IMPLEMENT TRAIL 1 Not used TRAIL 2 Not used TRAIL 4 Signal from a wheel sensor fitted to an implement TRAIL 7 Signal from an implement sensor fitted to the implement TRAIL 8 Not used TRAIL 15 Not used TRAIL 16 Not used BOM 1 12 Not used TEST OUTPUT OUT 1 Not used OUT 2 Not used OUT 3 Not used OUT 4 Not used POT 1 2 Not used 2 32 5000 OPERATORS MANUAL GENERAL FUNCTIONS DIESEL FLOW FIGURE The calibration figure can be found as follows Diesel Flow figure 0 001 Millilitre per pulse Example 1 The flowmeter specifications say that 1 pulse is generated for each millilitre fuel Diesel flow figure 1 ml 0 001 Diesel flow figure 1000 Example 2 The flowmeter specifications say that 1 pulse is generated for every 5 millilitre fuel Diesel flow figure 5 0 001 Diesel flow figure 5000 SPEED SIMULATION It is possible to simulate a speed for i e flow tests etc By pressing the
263. prayer 2 8 5000 OPERATORS MANUAL GENERAL FUNCTIONS DELETE TASK Move the cursor to the task to be deleted and press the Delete Task function key The entire contents for the selected task will now be deleted NOTE All tasks that contain data can be deleted regardless of the implement selected for operation so it is possible to delete tasks for e g slurry spreader even if the implement chosen for operation is a sprayer PRINT TASK Pressing the Print Task function key displays the following PRINT ONE Move the cursor to the task to be printed and press the Print Task function key The contents of the selected task will be printed NOTE All tasks that contain data can be printed regardless of the implement selected for operation so it is possible to print tasks for e g slurry spreader even if the implement chosen for operation is a sprayer Teglet 2 9 GENERAL FUNCTIONS TEEJET 5000 OPERATORS MANUAL PRINT ALL Pressing the Print All functions key prints all the tasks that contain data Once the computer has finished printing pressing the return key displays the following Pressing the Delete function key will delete all tasks If this is not desired pressing the cancel function key will return the computer to the previ
264. prayer 1000 Lt In this example 8 Press the flashing CALC FLOW and the flow figure is automatically calculated FILL MODE You can select whether a valve stops filling or whether a horn is blown when the correct amount has been filled into the sprayer Pressing the RETURN key brings the sprayer menu back 3 8 5000 OPERATORS MANUAL SPRAYER SPRAYER ENCODE This menu allows the operator to encode the various settings that are necessary for spraying Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements DOSERATE Encode the required application rate here if automatic rate control equipment is fitted to the sprayer or if you want an alarm to sound with incorrect application rates The application rate is encoded in whole litres per hectare The maximum application rate that can be encoded is 9999 I ha NOTE The required app
265. preading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements QU Oz gt QU WORKING WIDTH The working width for the spreader being used Each spreader section is encoded individually in centimetres section 1 is on the left hand side of the machine NB All unused sections must be encoded as O The total working width can be seen at the bottom of the display under encode 4 108 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR RAUCH BETA DELTA SPEED SENSOR 5000 V 4 fertiliser distributor program gives the option of choosing between 3 different speed sensors Wheel tractor Wheel spreader Radar WHEEL TRACTOR Speed sensor fitted on the tractor The sensor can be built into the tractor s gearbox or rear axle as standard factory fitted or be retrofit on a wheel or drive shaft NOTE Wheelslip will give inaccurate speed readings WHEEL SPREADER Speed sensor fitted to trailed spreaders This type of sensor will as a rule give a very accurate speed reading RADAR Signal from a radar fitted on the tractor
266. pulated manuals Original manuals can be requisitioned at any time from TeeJet Technologies With regards Maolhavevej 2 9440 Aabybro Denmark Tel 45 9696 2500 Fax 45 9696 2501 www teejet com General use aed ce RC Rata te ttt 1 2 CONSTANT rcli dates ed utente pe iem etae 1 9 RETURN KEY rw RE 1 3 TRACTOR INFO eee oen paciens Vet endete pene eon tients 1 3 SEP cut 1 3 niaenedi2fm 1 4 1 4 DELETE KEV eee rl rear aera Emus 1 4 BACKGROUND LIGHT te eco net oit tens 1 4 N MERICAL KEY S c nt 1 4 GENERAL USE TEEJET 5000 OPERATORS MANUAL GENERAL USE The TeeJet 5000 has been specifically developed to serve all commonly used implements within agriculture thus all tasks and implements can be operated and controlled by the same monitor via sensors The TeeJet 5000 menu system has in principal been built up as a book in which you can page through the different menus The computer functions are divided into programs Each program has been tailored for the implement in question The 6 function programs are Sprayer Fertiliser distributor Drill Baler Slurry spreader Other implements The functions available for each individual implement are described in each individual chapter The
267. r by the selected implement sensor REVS SENSOR Encode the number of pulses the sensors fitted to the drill shaft give per revolution It is also possible to select between clutch monitoring and RPM monitoring monitoring fan speed on pneumatic machines PTO SENSOR Encode 1 if the TeeJet PTO sensor kit 932 983 is used DRILL SHAFT SENSOR Encode the number of pulses the sensor fitted to the drill shaft gives per revolution sensors that generate fewer than 4 pulses per revolution cannot be used FAN SENSOR Encode the number of impulses the sensor gives per revolution 5 73 SEED DRILL SIMBA TEEJET 5000 OPERATORS MANUAL WARNING ENCODE The following warnings can be set in this menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warning ON OFF and MAX MIN limits for wheel slip in KG LEFT Warning ON OFF and amount of kg min at which the warning is wanted D SHAFT Warning ON OFF if the drill shaft stops turning HOPPER Warning ON OFF for empty seed hopper FAN Warning ON OFF and MAX MIN limits for revolutions DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY 5 74 leefet ENDE 9 BALER c p 6 2 BALER OPE
268. r is the same as the encoded rhythm LN track number Note where in the first 4 bouts around the whole field the bouts should be counted A and where bouts should not be counted all other corners 4 counting can be T controlled by using either the dd N w IN us 6 EN IN HOLD key by using the TRACK keys 5 38 leefet 5000 OPERATORS MANUAL TS R Eee Ho L du 3 7 1302 SEED DRILL LEMKEN Example of method B Uneven The encoded rhythm in the shown example is 3 2x2 solenoid shutters are fitted on pneumatic drills or 2 clutches are fitted on the middle of traditional machines Tramlines are made when the bout number is the same as the encoded rhythm track number Note where the bouts should be counted A and where bouts should not be counted all other corners in the first 3 bouts around the whole field Bout counting can be controlled by using either the HOLD key or by using the TRACK keys leefet 5 39 SEED DRILL LEMKEN TEEJET 5000 OPERATORS
269. r selected in encode wheel tractor wheel sprayer or radar AREA MEASUREMENT The worked area is displayed in Ha Area is displayed with 2 decimals from 0 to 99 99 ha And thereafter with 1 decimal from 100 to 999 0 ha NOTE a total counter for area can also be found in DATA DELETE FERTILISER DISTRIBUTOR FUNCTIONS KG HA Application rate in KG HA KG Fertiliser consumption in Kg KG LEFT Total KG remaining in the hopper the amount must be encoded before start Step dosage increase DOSE RATE Encoding required application rate or return to normal after using the step key 4 26 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BOGBALLE XX Percentile increase of the encoded application rate The size of the steps is altered in encode XX Percentile reduction of the encoded application rate The size of the steps is altered in encode NORMAL Only displayed if the step feature has been used Normal application rate Regardless of how many steps the application rate has been increased decreased by pressing this key will return the application rate to normal DOSE RATE Pressing this key allows the application rate to be altered directly from the operation screen see also DOSE RATE in encode Pressing the
270. r used Each spreader section is encoded individually in centimetres section 1 is on the left hand side of the machine NB All unused sections must be encoded as 0 The total working width can be seen at the bottom of the display under encode leefet 4 119 FERTILISER DISTRIBUTOR RAUCH AXERA TEEJET 5000 OPERATORS MANUAL SPEED SENSOR The TeeJet 5000 V 4 fertiliser distributor program gives the option of choosing between 3 different speed sensors Wheel tractor Wheel spreader Radar WHEEL TRACTOR Speed sensor fitted on the tractor The sensor be built into the tractor s gearbox or rear axle as standard factory fitted or be retrofit on a wheel or drive shaft NOTE Wheelslip will give inaccurate speed readings WHEEL SPREADER Speed sensor fitted to trailed spreaders This type of sensor will as a rule give a very accurate speed reading RADAR Signal from a radar fitted on the tractor This type of sensor gives a very accurate speed reading on hard surfaces but a high crop and reflecting surfaces water gives an inaccurate reading Please refer to chapter 2 for speed sensor calibration FERTILISER CALIBRATION PROCEDURE Three fixed application rates can be encoded and the calibration procedure can be done when this key is pressed A new calibration must be carried out each time 1 The first time the spreader is used 2 When the working width is changed 3 Change of fertiliser type A new cal
271. radar then select RADAR and forward speed will be measured from the radar Radar and the number of pulses per metre will be displayed at the top of the screen IMPORTANT Working in crops that are blowing in the wind or working in areas with surface water can affect the accuracy of the radar we recommend using a speed sensor fitted to the tractor under these circumstances WHEEL SLURRY SPREADER If the slurry spreader is fitted with a speed sensor then press the WHEEL SLURRY key The TeeJet 5000 will now use this sensor for forward speed measurement Please refer to chapter 2 for forward speed calibration IMPLEMENT SENSOR This sensor starts and stops the area counter A pressure sensor should be fitted on slurry spreaders between the pump and the distributor macerator so that the sensor generates a signal when the pressure drops If this is the case then SLURRY SPREADER should be selected If a sensor for PTO speed is fitted then this can be used as an area override sensor select PTO METRE SWITCH Select whether the metre counter is started stopped manually MANUAL or by the selected implement sensor IMPLEM SENSOR WORK HOUR ON OFF Select whether the timer function is started stopped manually via the function key in the operation menu or by the selected implement sensor 7 36 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER HORSCH REVS SENSOR
272. re full of seed Remember to empty the calibration tray bucket again before proceeding This screen is now displayed LOAD FIG The previous load figure NO OF PULSES The pulses are counted during calibration NO OF CALIB Shows the number of calibrations The drill shaft will rotate for 10 seconds when the CALIB Key is pressed The number of calibrations can be increased for each press of the key This gives the possibility of varying the amount and therefore the weight of the released seed so weighing in relation to the type of scales being used is as good as possible leefet 5 25 SEED DRILL NORDSTEN TEEJET 5000 OPERATORS MANUAL The screen changes once the drill shaft has rotated for the number of seconds encoded The weight of the released grain is encoded in grams under WEIGHT CALC flashes Pressing CALC Will calculate a new load figure which is displayed at the top of the screen The calibration procedure is now finished pressing the return key brings the ENCODE menu back STEP The size of the steps this percentile value is the same for both and KG LEFT To see how much seed is left in the hopper the amount filled into the seed drill must be encoded here NOTE If the
273. re is some seed left in the hopper before refilling then this amount must be added to the amount filled thus Amount left in hopper filled amount Kg left HA LEFT Encode the size of the field to be sown before work commences This encodement is also used to calculate end time SOW WIDTH The total working width of the seed drill is encoded here in centimetres 5 26 5000 OPERATORS MANUAL SEED DRILL NORSTEN TRACK NUMBER Encode the tramline rhythm here Example The working width of the seed drill is 3 m The working width of the fertiliser spreader sprayer is 15 m Track number 15 3 5 The tramlining method to be used is also selected here A amp B The methods are described in the seed drill operation section ROW NO Encode the total number of rows that the seed drill has ROWS IN TRACK Encode the number of rows that are shut when tramlines are being made This encodement is necessary for correct KG metering If the sown amount is not reduced when making tramlines encode 0 NB Pneumatic seed drills do not reduce the amount when tramlines are being made FORWARD SPEED SENSOR There is a speed sensor fitted to the seed drill that gives a suitable number of pulses for the TeeJet 5000 With the future in mind the computer is also able to receive signals from a sensor fitted onto a tractor or a radar sensor Please refer to chapter 2 for forward speed calibration IMPLEMEN
274. rect operation FORWARD SPEED Forward speed is shown in kilometres per hour with 1 decimal Forward speed is calculated from pulses from the sensor selected under encode wheel tractor wheel slurry spreader or radar NB Remember to reset the counters in DATA DELETE before starting SLURRY SPREADER FUNCTIONS The amounts metered be displayed in TON or cubic metre This can be selected in encode under DOSE RATE TON M3 Consumption in ton m slurry LEFT the amount remaining in the tank TON M3 MIN Consumption per minute TON M3 The amount of slurry spread since starting This function also works as a trip counter and is deleted in DATA DELETE where a total counter can also found see chapter 2 TON M3 LEFT The amount remaining in the tank Presupposes correct encodement of the tank size under TANK VOLUME in encode Each time FULL TANK is pressed the amount encoded in TANK VOLUME is transferred to TON M3 LEFT and the slurry spreader is ready for a new load This function is also used for calibration of the flowmeter see page 7 22 TON M3 MIN amount per minute through the flowmeter 7 18 Teglet TEEJET 5000 OPERATORS MANUAL SLURRY SPREADER OTHER TYPE HYDR Pressing the NEXT PAGE key displays the next functions Step dosag
275. rive motor motor depending on drill model TRAIL 4 Speed signal from sensor fitted Speed signal from sensor fitted to the seed drill to the seed drill TRAIL 7 Signal from the implement Signal from the implement sensor fitted on the drill sensor fitted on the drill TRAIL 8 Signal from the RPM sensor Signal from the RPM sensor fitted on the fan fitted on fan 1 TRAIL 15 Signal from the hopper level Signal from the hopper level sensor fitted in the seed hopper sensor fitted the seed hopper empty tank empty tank TRAIL 16 Not used Signal from the RPM sensor fitted on fan 2 BOM 1 12 Not used BOOM 2 Signal from the RPM sensor fitted to drill shaft 2 BOOM 8 Signal from the RPM sensor fitted on fan 2 BOOM 1 3 7 9 12 Not used TEST OUTPUT OUT 1 Signal that controls the Signal that controls the tramlining for the left side of the tramlining tramlines are made drill tramlines are made on the when OUT 1 is pressed left side when OUT 1 is pressed OUT 2 Signal that controls the speed of Signal that activates 1 2 and 1 1 the drill shaft drive motor the working width drill shaft turns when OUT 2 is pressed OUT 3 Signal that controls the Not used tramlining for the right side of the drill tramlines are made on the right side when OUT 2 is pressed OUT 4 Not used Not used POT 1 2 Not used Not used 2 28 Teejet 5000 OPERATORS MANUAL GENERAL FUNCTIONS TEST I
276. rks as a total counter and can be reset deleted DATA DELETE D HA The present diesel consumption in litres per hectare Use the function to optimise work present diesel consumption per hour Use this function to optimise work Teefet 8 3 OTHER IMPLEMENT TEEJET 5000 OPERATORS MANUAL OTHER IMPLEMENT ENCODE This menu allows the operator to encode the various settings that are necessary for operation Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements zZ 1 0 f W W I A S W Encode the size of the field to be spread here END TIME is calculated from this encodement WORKING WIDTH The effective working width of the implement encoded in centimetres 8 4 Teejet 5000 OPERATORS MANUAL OTHER IMPLEMENT FORWARD SPEED SENSOR The TeeJet 5000 V 4 other implement program gives the option of choosing between 3 different speed sensors Wheel tractor Wheel spreader Radar WHEEL TRACTOR The speed signal can come from a sensor fitted in the gear box or on a drive s
277. rocedure is carried out at the same time as the normal spreader calibration The principle works by counting the number of pulses given from the sensor during spreader calibration When the calibration is finished the amount released is weighed and encoded the computer can now calculate the amount released per pulse Procedure Prepare the spreader for calibration 1 The picture to the left is displayed when CALIB PROCED has been selected 2 NO OF PULSES must be 0 before the calibration procedure is continued If the number is higher then press the RETURN key and select CALIB PROCED again 3 Pressing the 2 key allows you to adjust the speed of the motor that drives the floor chain pressing the key increases the chain speed and pressing reduces the chain speed The speed of the floor chain is displayed 4 Set the chain speed to 0 using the key when a suitable amount has been released and press OK Move the cursor to WEIGHT and encoded the amount released using the numerical keys NOTE The pulse counter must have counted a number of pulses 5 Press the flashing CALC Key and the calibration procedure is finished The CAL FIG which is displayed at the top of the screen can be noted 4 130 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR REI MANUAL CALIBRATION The CAL FIG Can be calculated m
278. s FILL MENU Before the slurry spreader is used a PWM calibration of the proportional valve MUST be carried out This PWM calibration is normally carried out by the engineer when fitting the system to the slurry spreader The procedure for this calibration is described in the PWM section under ENCODE It is possible to use a fixed displacement pump for filling the slurry spreader When the fill signal and the implement signals are active the pump will run at a pre encoded speed 1 Set the spreader to fill 2 Press the and keys to adjust the required pump speed 3 The pump speed will change and the actual RPM is displayed 4 When the required pump speed has been reached press the RETURN key Teejet 7 51 SLURRY SPREADER ZUNHAMMER TEEJET 5000 OPERATORS MANUAL PWM Calibrating the proportional valve is necessary to protect the proportional valve against too much power This calibration is normally carried out by the engineer during fitting the equipment on the slurry spreader The procedure is however described below It is not recommended to carry out this calibration procedure without competent knowledge of power measuring The procedure is thus 1 Connect a meter in series between TeeJet 5000 OUT output Max 100mA Out1 12V 2 Pressing the and keys alters the PWM
279. s follows Sections 1 and 5 50 centimetres Sections 2 and 4 150 centimetres Section 3 1200 centimetres It is now possible to reduce the spreading width from 16M to 15M by closing sections 1 and 5 closing sections 2 and 4 thereafter reduces the working width to 12M Which sections are open closed is displayed on the screen BOOM SECTIONS ON OFF Pressing this key starts or stops slurry spreading Can only be used if SLURRY SPREADER has been selected as the implement sensor under IMPLEM SENSOR in encode Also works as the area override sensor The picture to the left shows a slurry spreader with 2 boom sections encoded One section is open and one section is closed To open the other section press the number 2 on the numerical keypad for approx 3 seconds To close the first section press number 1 on the numerical keypad for approx 3 seconds When the area override sensor is activated not I counting area I is displayed and all sections will disappear 7 20 Teglet TEEJET 5000 OPERATORS MANUAL SLURRY SPREADER OTHER TYPE HYDR SLURRY SPREADER ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements
280. shaft drive motor the shaft is rotated slowly the status changes between HI and LO and the number of impulses is registered The status changes to LO if the shaft is turned quickly TRAIL 4 Signal from the hopper level Speed signal from sensor fitted sensor empty hopper to the seed drill TRAIL 7 Area override on off signal from Area override signal from sensor sensor fitted to seed drill i e fitted to seed drill marking system or when the drill is raised TRAIL 8 Not used Signal from RPM sensor fitted to the fan or to the left clutch depending on drill model TRAIL 15 Not used Signal from the hopper level sensor empty hopper TRAIL 16 Not used Signal from RPM sensor fitted to the right clutch BOM 1 12 Not used Not used TEST OUTPUT OUT 1 Motor signal for when tramlines Signal to control tramlining are to be made Pressing OUT 1 makes tramlines OUT 2 Not used Signal to control the speed of the drill shaft motor Pressing OUT 2 rotates the drill shaft OUT 3 Not used Not used OUT 4 Not used Not used POT1 2 Not used Not used Telet 2 27 GENERAL FUNCTIONS TEEJET 5000 OPERATORS MANUAL TEST INPUT LEMKEN SIMBA TRAIL 1 Signal from the RPM sensor Signal from RPM sensor fitted fitted on the drill shaft on drill shaft 1 TRAIL 2 Signal from the RPM sensor Signal from the RPM sensor fitted on the drill shaft drive fitted on the drill shaft d
281. sing this key calculates the application rate since the last calculation It is possible to continue weighing spreading once this key has been pressed DRIVE END Press this key when you have stopped spreading or when the spreader is to be filled The application rate since the last calculation is calculated when this key is pressed The amount is also registered in the KG counter If the task function is being used then the consumed amount will be stored in the task that was opened before spreading commenced PAUSE Pressing the PAUSE key allows a pause in spreading and stops the beeps from the computer It is possible to start spreading again at anytime leefet 4 5 FERTILISER DISTRIBUTOR OTHER TEEJET 5000 OPERATORS MANUAL 2 PULSE WEIGHING Metering the amount spread using pulses from a spreader fitted with feed roller KG The amount spread in KG KG LEFT The amount left in the spreader RPM 1 Shaft speed for axle no 1 KG The amount spread metered from a pulse generator fitted to the feed roller Presupposes system calibration amount per pulse KG LEFT The amount left in the spreader Presupposes encodement of the amount filled into the spreader before spreading starts encode RPM 1 Shaft speed for axle no 1 3
282. st dosage using the amount in the sprayer REST METRE Remaining distance with the amount REST DOSAGE REST METRE in the sprayer Displays the application rate needed to finish the field with the chemical remaining in the tank Calculated from the amount left in the tank and the remaining area Displays the distance that can be travelled using the chemical remaining in the tank with the present application rate Pressing the NEXT PAGE key displays the next set of functions AUTO MAN Automatic or manual application i Increase the application rate only displayed if MAN is selected Decrease the application rate only displayed if MAN is selected Teglet 3 5 SPRAYER TEEJET 5000 OPERATORS MANUAL AUTO MAN Pressing this key selects automatic or manual application If manual operation is selected flashes in the lower part of the screen and and appear as function keys Increased application The application rate is increased as long as this key is pressed The speed at which the application rate increases depends on the speed of the regulating system s operating speed only displayed if MAN is selected Decreased application The application rate is reduced long as this key is pressed The speed at which the application rate decreases depends on the speed of the regula
283. st used Q DOR method Tramlines are made when the bout number is the same as the track number 2523 Example of method Uneven The encoded rhythm in the shown example is 3 2x2 solenoid shutters are fitted on pneumatic drills or 2 clutches are fitted on the middle of traditional HH machines Tramlines are made when the bout number is the same as the encoded rhythm track number Note where the bouts should be counted A and where bouts should not be counted all other corners in the first 3 bouts around the whole field i Bout counting be controlled VJ by using either the HOLD key lt keys 5 20 leefet 5000 OPERATORS MANUAL MM V Li p E L SEED DRILL NORSTEN Example of method B Even The tramline cannot be split over 2 bouts in this example with a rhythm of 4 encoded The first bout can only be sown with one half of the drill open Once this is done the tramlines can be made with either 2x2 solenoid shutters or 2 clutches fi
284. step forward in the tramline rhythm TRACK 1 Moves one step backward in the tramline rhythm Pressing the NEXT PAGE key displays the first available functions 5 35 SEED DRILL LEMKEN TEEJET 5000 OPERATORS MANUAL SELECTING THE TRACK RHYTHM To meet the different needs of different markets the Lemken program has four methods A B C and D of controlling the how the tramlines are made The method to be used is selected under encode METHOD A Q Ea ees A _______ MN 9 TO ou Example of Method A Even A rhythm of 4 is encoded in this example A single clutch or 1x2 solenoid shutters is fitted on the left hand side of the seed drill Tramlines are made in bout numbers 2 and 3 split when a rhythm of 4 is encoded Note where in the first 4 bouts around the whole field the bouts should be counted A and where bouts should not be counted all other corners After each trip around the field the machine is turned around and is driven in the opposite direction Bout counting can be controlled by using either the HOLD key or by using the TRACK keys 5 36 5000 OPERATORS MANUAL SEED DRILL LEMK
285. t has actually happened in the field Job computer TeeJet 5000 DGPS version can be used as a job computer in connection with another computer switch DGPS to OFF as described on the following page The TeeJet 5000 will control the implement when application set points are received from the other computer via the serial connection For further information regarding data transfer and mapping in general please consult the user manual for the PC software used Note The TeeJet 5000 must be connected to a TeeJet DGPS module and a TeeJet DataLink module plus be a DGPS version before the computer can work with the available DGPS functions 9 2 Teglet 5000 OPERATORS MANUAL DGPS SELECTING THE DGPS FUNCTIONS The DGPS menu is selected thus 1 Using the arrow keys move the cursor to SYSTEM When this is done press the SELECT key 2 Main menu Selecting system 3 System menu Selecting DGPS system 4 Pressing ON displays the available DGPS functions main DGPS menu 5 Returning to this screen at any time and pressing OFF will switch the DGPS functions off and the TeeJet 5000 will function as normal 6 Moving the cursor with the arrow keys to the required function and pressing the SELECT key will display the function
286. t only be used when the belt has stopped override sensor is active The gate will open automatically when spreading starts again SECTION ON OFF This picture is displayed during spreading When the area override sensor is activated not I counting area I is displayed and all sections will disappear FERTILISER DISTRIBUTOR ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements O lt 03 0 01 gt 4 40 TEEJET 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL DOSERATE The effective spreader width must be encoded under DISTRIB WIDTH before DOSE RATE is selected Some spreaders are fitted with a gt gear It is possible to change the calculated gear by pressing the key A new calculation must take place after changing the gear if the calculated scale is greater than 300 then GEAR must be changed
287. th are important to gain the correct application rate FORWARD SPEED The forward speed is displayed with 1 decimal Forward speed is calculated from the signal from the speed sensor selected in encode wheel tractor wheel sprayer or radar Teglet 3 3 SPRAYER TEEJET 5000 OPERATORS MANUAL SPRAYER FUNCTIONS LITRE LITRE LEFT LITRE MIN LITRE The amount of chemical consumed in litres LITRE LEFT Litres left in the tank the amount filled must be encoded before starting LITRE MIN Litres per minute Consumed litres since starting This function works as a trip counter The amount can be deleted in DATA DELETE where a total counter can also be found The amount of chemical left in the tank Presupposes that the amount filled in is encoded before starting If the optional filling flowmeter is used then this is automatic Litre left is also used for checking and calibrating the flowmeter see page 3 Error Unknown switch argument Litres per minute through the flowmeter Should not be confused with the pump capacity Pressing the NEXT PAGE key displays the next functions XX Step dosage increase XX Step dosage decrease DOSE RATE NORMAL DOSE Encoding required application rate or return to norm
288. the programs area time amp tractor functions all of the other functions will be described one by one 4 2 Teefet 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR OTHER TYPE FERTILISER DISTRIBUTOR OPERATION OTHER TYPE FORWARD SPEED The primary function under fertiliser distributor is forward speed Forward speed is displayed in KPH with 1 decimal Forward speed is calculated from the signal from the speed sensor selected in encode wheel tractor wheel spreader or radar APPLICATION RATE IN KG HA When WEIGHING or PULSE WEIGHING is selected area measurement is displayed AREA MEASUREMENT The worked area is displayed in Ha Area is displayed with 2 decimals from 0 to 99 99 ha And thereafter with 1 decimal from 100 to 999 0 ha NOTE A total counter for area can also be found in DATA DELETE FERTILISER DISTRIBUTOR FUNCTIONS Three different function sets can be displayed in this menu The following can be selected in ENCODE WEIGHING PULSE WEIGHING RPM 2 The function sets for each possibility are described in the following 1 WEIGHING DIRECT WEIGHING WITH WEIGH CELLS KG Fertiliser consumption in KG TARRING Tarring the weigh cell s DRIVE START Pressing this key stores the present weight the TeeJet 50005 memory RPM 1 Revolutions per minute 43 F
289. the colour code on the label DIESEL FLOWMETER Connect to connecting block 3 1 2 according to the colour code on the label RADAR Connect to connecting block 2 8 10 according to the colour code on the label POWER SUPPLY Connect to connecting block 3 11 12 according to the colour code on the label IMPLEMENT SENSOR Connect to connecting block 3 3 4 according to the colour code on the label PTO SENSOR RPM Connect to connecting block 3 5 7 according to the colour code on the label SPEED SENSOR Connect to connecting block 3 8 10 according to the colour code on the label Teefet 12 13 FITTING INSTRUCTIONS TEEJET 5000 OPERATORS MANUAL BREAK AWAY PLUG CONNECTIONS As there are only 7 pins in the breakaway plug and there many different possible sensor connections each pin in the plug has a different function depending on which implement is being used The following describes how each sensor should be connected for each individual implement If one of TeeJet Technologies complete implement kits is used then the correct connections are taken into consideration and the sensors need only be connected as shown in the fitting instructions for the implement Breakaway plug for the implement seen from the fitting side 8234 0832 SPRAYER SENSOR WIRECOLOUR PINNUMBER FLOWMETER BLACK 6 SPEED SENSOR BROWN BUE 6 PRESSURE SENSOR 12 14 Teglet 5
290. then GEAR must be altered again Please refer to the documentation supplied with the spreader for more information 4 67 FERTILISER DISTRIBUTOR BREDAL HYDR TEEJET 5000 OPERATORS MANUAL The required application rate and spreader setup is encoded thus Encode the required application rate with the numerical keypad under DOSE TON HA The SPECIFIC GRAVITY is found using the specific gravity tester supplied by BREDAL Pressing CALC CALIB Calculates the correct SCALE and GEAR This menu cannot be left until CALC CALIB has been pressed The required DOSE RATE along with the specific gravity and the distributor width gives The scale setting The correct gear on the spreader NOTE The settings must be re calculated under DOSE RATE each time the working width of the spreader has been altered TON LEFT The amount filled into the spreader must be encoded here to be able to see how much lime is left in the hopper NOTE If there is some lime left in the hopper before refilling then this amount must be added to the amount filled thus Amount left in hopper filled amount Ton left HA LEFT Encode the size of the field to be spread here END TIME is calculated from this encodement 4 68 5000 OPERATORS MANUAL FERTILISER DISTRIBUTOR BREDAL HYDR P VALVE CALIBRATION The proportional valve and the co
291. this menu It is recommended to turn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warning ON OFF and MAX MIN limits for wheel slip in KG LEFT Warning ON OFF and amount of kg min at which the warning is wanted D SHAFT Warning ON OFF if the drill shaft stops turning HOPPER Warning ON OFF for empty seed hopper CLUTCH Warning ON OFF for if the clutches used for tramlining stop working DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY 5 14 Seed drill Nordsten NORDSTEN ELECTRONIC SEED DRILL ened 5 16 6556 dO 5 17 EC 5 17 TRAMLINE sna ue 5 17 KOMA Dc 5 17 HOLD KEY eum 5 18 SELECTABLE SEED DRILL FUNCTIONS aude 5 18 STEP FUNG ON ener creer 5 18 MANUAL START STOP e 5 19 MANUAL 5 19 RPM 5 19 SELECTI
292. time the computer is connected to another spreader 4 76 5000 OPERATORS MANUAL BREDAL S LIME SPREADER FERTILISER DISTRIBUTOR BREDAL K RAMP 1 Select fertiliser distributor from the main menu as follows 2 Move the cursor using the arrow keys to FERTIL DISTRIB Press the SELECT key 3 Main menu select fertiliser distributor 4 ACCEPT or SELECT TYPE 5 Select type 6 It is now possible to choose between the displayed types 7 Select fertiliser distributor type 8 Accept type It is now possible to select between the following functions OPERATION ENCODE DATA DELETE TASK OPERATION TASK OPERATION is described in General Functions section 2 together with the functions that are available in all of the programs area time amp tractor functions all of the other functions will be described one by one leefet 4 77 FERTILISER DISTRIBUTOR BREDAL K RAMP TEEJET 5000 OPERATORS MANUAL LIME SPREADER O
293. ting system s operating speed only displayed if is selected Pressing the NEXT PAGE key displays the first set of functions EXTRA TRACTOR FUNCTIONS IN THE SPRAYER PROGRAM METRE IN TRACK Distance driven in the present tramline METRE Distance driven METRE START METRE STOP Manual start and stop of the distance counter METRE IN TRACK Distance driven in the current tramline This function is used to after refilling find the precise position in the tramline at which the sprayer ran empty This function works in conjunction with REDUCE TRACK which appears when the sprayer is switched off This function works in the following way Each time the sprayer is switched on again when starting a new tramline the METRE IN TRACK counter starts from 0 The computer remembers how far in the tramline has been driven if the sprayer is shut somewhere the middle of the track The function REDUCE TRACK is now displayed NOTE Once the sprayer has been shut in the tramline do not open the sprayer again before the sprayer is full and the computer is ready as follows Fill the sprayer again and drive to the start of the last tramline that was partially sprayed Press REDUCE TRACK and drive down the tramline An alarm will sound and SPRAYER SOON TO BE OPENED will be displayed 5 metres before the sprayer should be opened When the tractor reaches the position at which the sprayer sho
294. tion HOPPER Amount remaining in tank POS HOPPER Pressing this key displays the gate position changes between the left and right hand side The calculated fertiliser amount remaining in the tank Presupposes encodement of the amount filled into the hopper before work commences 4 117 FERTILISER DISTRIBUTOR RAUCH AXERA TEEJET 5000 OPERATORS MANUAL 2 MANUAL APPLICATION CONTROL HA KG KG REST HA Area KG Consumption in KG KG LEFT How many KG are left in the hopper at present Area counter Worked area since the last reset NOTE Total area counter is found in DATA DELETE Total KG used calculated from forward speed and gate position This function presupposes correct calibration NOTE Total KG counter is found in DATA DELETE Total KG remaining in the hopper the amount must be encoded before start Pressing the NEXT PAGE key displays the next functions EMPTY HOPPER AUTO MAN EMPTY HOPPER Pressing this key opens the gate completely to enable the hopper to be emptied AUTO MAN Changing between automatic or manual operation To ease emptying the hopper The gate can be opened completely by pressing this key Pressing this key changes between automatic and manual application control During manual op
295. tted to the middle of the drill NB Tramlines are made when the present bout number is the same as the encoded rhythm track number Note where in the first 4 bouts around the whole field the bouts should be counted A and where bouts should not be counted all other corners Bout counting can be controlled by using either the HOLD key or by using the keys 5 21 SEED DRILL NORDSTEN TEEJET 5000 OPERATORS MANUAL METHOD A The difference between method A and B uneven rhythm is minimal The only difference is when tramlines are made Method A makes tramlines in the middle of the rhythm see the following example Oz 4 At Example of Method A Uneven In this example the encoded rhythm is 3 Two clutches or 2x2 solenoid shutters f fitted in the middle of the drill Tramlines are made in bout number 2 when a rhythm i track number of 3 is Note where first 3 bouts around the field the present bout should A be counted and the bout should not be counted After each trip Wf direction Bout counting vt 2 3 gt controlled by using either the HOLD key or by using the TRACK keys
296. tuni en Cus 2 15 B sypsiplEIIp IC 2 16 FORWARD SPEED SENSOR ee 2 17 Vini CIR MT 2 17 WHEELIMPLEMEN P esses epe 2 17 RADAR 2 17 MANUAL CALPIBISATIOBL 2 18 AUTOMATIC SPEED SENSOR 2 19 a 2 20 TEST INPUT OUTPUT S 2 21 TEST INPUT OUTPUT SPIRAY EIR 2 22 TEST INPUT OUTPUT FERTILISER SPREADER ptr ett 2 23 TEST INPUT OUTPUT SEED DRILL teeter Rn ve 2 27 TESTINPOTOBTPUT BALER Ee EE a 2 29 TEST INPUT OUTPUT SLURRY SPREADER 2 30 TEST INPUT OUTPUT OTHER IMPLEMENT rrr ttn acne 2 32 DIESEL FLOW ddgtci i 2 33 op Be EN M 2 33 GPS SYSTEM He cU 2 33 SYSTEM DATA e ET 2 33 msi sic RE s mer nee rererr terre 2 33 GENERAL WARNINGS 2 34 GENERAL FUNCTIONS TEEJET 5000 OPERATORS MANUAL GENERA
297. u It is recommended to turn all warnings which not wanted OFF PTO Warning ON OFF MAX MIN limits for revolutions KM H Warning ON OFF MAX MIN limits for speed SLIP Warning ON OFF MAX MIN limits for wheel slip in RPM 1 Warning ON OFF MAX MIN limits for revolutions Encode as RPM TON LEFT Warning ON OFF and amount in tons minimum at which warning is wanted NB The encoded limits must exceed the limits encoded If a warning is required when an axle stops 0 RPM then set the minimum limit to 1 DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY 4 73 FERTILISER DISTRIBUTOR BREDAL HYDR K TEEJET 5000 OPERATORS MANUAL 4 74 Fertiliser distributor Bredal K Ramp INTRODUC THON 4 76 BREDAL S LIME SPIREADELR FEE FERE ER eH ERO 4 77 LIME SPREADER OPERATION pes poste tee 4 78 LIME SPREADER FUNG TONGS onssc3snnsomcamnactzarntennaprsetbimsteietensntntmniessscacioeeaatetas 4 78 SPREADER ON OFF AP 4 81 LIME SPREADER ENCOBE 4 82 EFE ER rT 4 82 4 83 HACER 4 83 P VALVE CAEIBRATIOBL
298. uld be opened again the computer will give another audible warning and START SPRAYING NOW will appear on the display The alarm will continue until the sprayer is opened METRE The distance driven in metres Measured from the selected speed sensor and can be started stopped manually or with the override sensor Select how in encode under METRE SWITCH Or 3 6 5000 OPERATORS MANUAL SPRAYER METRE START METRE STOP Manual start or stop of the metre counter These function keys appear instead of METRE when manual control of the metre counter is selected BOOM SECTION ON OFF The picture to the left shows a sprayer with 2 sections where one is open and one is closed The total number of boom sections is set under encode When the area override sensor is activated not counting area is displayed and all boom sections will disappear p FILLING FUNCTION Pressing the Hold key selects the filling function The amount to be filled in the sprayer can be seen FILL VOLUME The amount to filled to the sprayer calculated from LITRE LEFT HA LEFT TANK VOLUME and the required application rate FILLED VOLUME The amount metered by the flowmeter LITRE LEFT Calculated LITRE LEFT in the sprayer If the calculated LITRE LEFT is
299. unction for slurry spreaders is application rate The application rate is displayed in TON M3 per hectare This rate is calculated from the flow through the flowmeter and area measurement forward speed and working width It is therefore necessary to both drive and spread to see this function NOTE To ensure correct operation the flowmeter must be calibrated the correct wheel circumference and the correct working width must be encoded FORWARD SPEED Forward speed is displayed in kilometres per hour with 1 decimal Forward speed is calculated using the sensor selected under encode wheel tractor wheel spreader or radar NOTE Remember to reset all counters in DATA DELETE before starting SLURRY SPREADER FUNCTIONS wiTH FLOW METERING The metered amount can be displayed in either TON or M3 cubic metres These options are selected in encode under DOSERATE TON M3 Slurry consumption in ton or M3 TON M3 REST The amount left in the tank TON M3 MIN Consumption per minute TON M3 The amount of slurry spread since starting This function works as a trip counter and can be deleted in DATA DELETE The total counter is also found here Teejet 7 43 SLURRY SPREADER ZUNHAMMER TEEJET 5000 OPERATORS MANUAL TON M3 REST The amount remaining in the tank This function presupposes encodement of the tank size TANK VOLUME in encode Every ti
300. urn all warnings which are not wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions Warning ON OFF MAX MIN limits for speed SLIP Warning ON OFF MAX MIN limits for wheel slip in KG LEFT Warning ON OFF and amount of kg min at which warning is wanted RPM 1 Warning ON OFF and MAX MIN limits for shaft speed Encode in RPM NB The encoded limits must exceed the limits encoded If a warning is required when an axle stops 0 RPM then set the minimum limit to 1 NOTE ALARM DOSE RATE When the spreader handle goes bellow 1 5 or when the application rate forward speed are such that the handle goes above the max On the scale an alarm will sound This alarm cannot be switched off DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY leefet 4 33 FERTILISER DISTRIBUTOR BOGBALLE TEEJET 5000 OPERATORS MANUAL 4 34 Fertiliser distributor Bredal B2 B3 B4 amp B6 T rene er ere ee ee 4 36 BREDAL FERTILISER DISTRIBU POTIS 4 37 FERTILISER DISTRIBUTOR OPERATION 4 38 FERTILISER DISTRIBUTOR FUNGCT ION GS rure irr et ttr tnnc 4 38 CLOSING THE a aces et ana get 5 50 000040005 as asd 4 40 SEC TON DRUGS 4 4
301. uts around the whole I field the bouts should be counted A and where bouts should not j be counted all other corners After each trip around field the machine is turned around and is driven in the opposite direction Bout counting can be DX PG 7 controlled by using either C the HOLD key or by using the TRACK N 7 keys C N OR 9209 02 5 67 SEED DRILL SIMBA METHOD B UNEVEN A rhythm of 3 is encoded in this example and there are 2 clutches fitted in the middle of the seed drill NB Tramlines are made when the present bout is the same as the encoded rhythm track number Note where in the first 3 bouts around the whole field the bouts should be counted A and where bouts should not be counted all other corners Bout counting can be controlled by using either the HOLD key or by using the TRACK keys TEEJET 5000 OPERATORS MANUAL 1 9 42 1 5 68 5000 OPERATORS MANUAL SEED DRILL SIMBA METHOD B EVEN
302. vals Some PC programs clear the card up each time a task is transferred to the card However not all PC programs have this function There are two types of files generated by the PC program or the TeeJet 5000 DataLink module File type Description inp Input file X Files with this suffix are created by the TeeJet 5000 DataLink module with field boundary measurement soil sampling data logging and the automatic data logging that takes place whenever a task from the data card is carried out out Output file Files with this suffix are created by the PC program and contain task information These files are placed in the DATEN directory on the PCMCIA data card and can be copied deleted etc in a file management program such as Windows Explorer Please refer to the original documentation for the file management program There are other files and directories on the PCMCIA data card that are essential for correct operation of the DataLink module These must not be altered or removed from the data card 9 10 Teglet Fitting instructions FITTING INSTRUCTIONS TEEJET 5000 VER 4 12 3 GENERAL OVERVIEW cete tcm dexter mies tdi edet tad ea erae 12 4 SPARE PARTS atic ed ah ns et ld 12 5 FITTING THE GOMPUTER E 12 6
303. wanted OFF PTO Warning ON OFF and MAX MIN limits for revolutions KM H Warning ON OFF and MAX MIN limits for speed SLIP Warning ON OFF and MAX MIN limits for wheel slip in KG LEFT Warning ON OFF and amount of kg min at which warning is wanted RPM 1 Warning ON OFF and MAX MIN limits for shaft speed Encode in RPM NB The encoded limits must exceed the limits encoded If a warning is required when an axle stops 0 RPM then set the minimum limit to 1 DATE CLOCK Set the date and time in this menu HOURS MINUTES YEAR MONTH DAY 4 46 Fertiliser distributor Bredal HYDR B INTRODUC TION 4 48 BREDALS FERTILISER SP READER 4 49 FERTILISER SPREADER OPERATION 5 arent e teten incer e oportet 4 50 FERTILISER SPREADER FUNC TIONS aaron tr tre ioo rotto srt ttr teens 4 50 SPREADER ON OFF M E 4 52 FERTILISER SPREADER 2 2 iubens s 4 53 oo 4 53 4 54 HATER 4 54 P 4 55 AUTOMAN 4 56 DISTRIBUTOR 4 56 WEIGHING
304. will happen automatically TANK VOLUME is transferred to TON M3 counter TANK VOLUME is added to the total counter for consumed amount which can be found in DATA DELETE 7 6 Teglet 5000 OPERATORS MANUAL SLURRY SPREADER OTHER CALCULATING M3 HA OR TON HA Each time EMPTY TANK is pressed the TeeJet 5000 calculates the amount spread with this tank full This makes it possible to find the correct forward speed PTO RPM and therefore the application rate for the last 1 2 loads An accurate calculation demands a constant forward speed and PTO speed and correct encodements SLURRY SPREADER ENCODE This menu allows the operator to encode the various settings that are necessary for spreading Each implement has it s own set of encodements Encodements such as speed sensor and its calibration have their own values under each implement Always check these encodements in the status screen each time you change implements Qo OI DOSERATE Encode the required appli
305. wn on the bottom left hand side of the screen Press SELECT when the correct task has been chosen The TeeJet 5000 will notify the operator if the task has been worked on before it is possible to continue with the task by pressing the CONTINUE key or cancel by pressing the RETURN key When a task has been selected the TeeJet 5000 will change to the normal operating screen for the correct implement NOTE Two new function keys will appear in the operation screen for the implement One of the keys allows the operator to switch between DGPS and manual application rate The other key displays the required application rate according to the present task application map If there is any doubt about whether the DGPS application is correct or not we recommend using MANUAL APPLICATION TEEJET 5000 DATALOG When this function is selected the TeeJet 5000 changes to the normal TeeJet5000 implement selection screen Operation of the computer is now as for standard TeeJet 5000 as described in each individual implement s section in this manual In TeeJet 5000 DATALOG MODE all alterations to the application rate will be recorded together with the position onto the PCMCIA card thus enabling the user to create a map of what has actually happened in the field 9 8 Teglet
306. xt functions 4 105 FERTILISER DISTRIBUTOR RAUCH BETA DELTA TEEJET 5000 OPERATORS MANUAL POS Actuator position Reference figure for the gate position only displayed on this page in the DELTA program HOPPER POS HOPPER Amount remaining in tank Pressing this key displays the gate position changes between the left and right hand side The calculated fertiliser amount remaining in the tank Presupposes encodement of the amount filled into the hopper before work commences MANUAL APPLICATION CONTROL HA KG KG REST HA Area KG Consumption in KG KG LEFT How many KG are left in the hopper at present Area counter Worked area since the last reset NOTE Total area counter is found in DATA DELETE Total KG used calculated from forward speed and gate position This function presupposes correct calibration NOTE Total KG counter is found in DATA DELETE Total KG remaining in the hopper the amount must be encoded before start Pressing the NEXT PAGE key displays the next functions EMPTY HOPPER Pressing this key opens the gate completely to enable the hopper to be emptied only found in the BETA program RPM Disc speed AUTO MAN Changing between automatic or manual operation
307. y using the numerical keypad ROW NO Encode the total number of rows that the seed drill has ROWS IN TRACK Encode the number of rows that are shut when tramlines are being made This encodement is necessary for correct KG metering If the sown amount is not reduced when making tramlines encode 0 SOW WIDTH The seed drill s effective working width in Cm leefet 5 11 SEED DRILL OTHER TEEJET 5000 OPERATORS MANUAL FORWARD SPEED SENSOR The TeeJet 5000 V 4 seed drill program Other type gives the option of choosing between 2 different speed sensors Wheel tractor Radar WHEEL TRACTOR The speed signal can come from a sensor fitted in the gear box or on a drive shaft or from a sensor fitted on a wheel depending on the make and model of the tractor used for sowing RADAR If the tractor is fitted with radar then select and forward speed will be measured from the radar Radar and the number of pulses per metre will be displayed at the top of the screen IMPORTANT Working in areas with surface water can affect the accuracy of the radar we recommend using a speed sensor fitted to the tractor under these circumstances Please refer to chapter 2 for forward speed calibration IMPLEMENT SENSOR The implement override sensor starts and stops area counting and counts bouts Pressing this key gives the following options LIFT DRILL The selected sensor is shown at the top of the display
308. y found in the DATA DELETE function and cannot be selected in OPERATION 2 16 5000 OPERATORS MANUAL GENERAL FUNCTIONS FORWARD SPEED SENSOR There are 3 possible speed sensors available in each of the TeeJet 5000 version 4 xx implement programs WHEEL TRACTOR WHEEL IMPLEMENT Wheel sprayer Wheel spreader etc RADAR The best speed sensor for the implement in question is described in each of the implement s chapters but the calibration procedure for each sensor type is almost the same WHEEL TRACTOR The speed signal can come from a sensor fitted in the gear box or on a drive shaft or from a sensor fitted on a wheel depending on the make and model of the tractor used for fertiliser spreading As the distance driven per pulse can be low for i e a sensor fitted in the gearbox the distance per pulse is encoded in centimetres with 3 decimals Pressing the WHEEL TRACTOR key allows the operator to select which sensor the TeeJet 5000 gets it s speed signal from The selected sensor is always shown at the top of the display along with the distance per pulse The TeeJet 5000 has an automatic speed calibration program that should be used for sensors that generate more than 1 pulse per metre The automatic calibration procedure can also be used for normal speed sensors if the distance per pulse is not greater than 100 cm Wheel circumference divided by number of magnets Manual speed calibratio

fertiliser distributor functions

Contents

Download Pdf Manuals

Related Search

Related Contents